Stamina Products 55-1537C User Manual

Owner's Manual

! WARNING !

Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

CAUTION:

2006, 11

Weight on this product should not exceed 300 lbs.

1.
Class H equipment: This equipment is for home

2.
use only. It is not for commercial use.

This Product is Produced Exclusively by

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

www.stamin aproducts.com

When calling for parts or
service, please specify the
following number.

55-1537C

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

2006 Stamina Products, Inc.

TABLE OF CONTENTS

Page Page

Safety Instructions 2
Before Y ou Begin 4
Hardware Identification Chart 5
Assembly Instructions 6
Operational Instructions 11
Storage 15

SAFETY INSTRUCTIONS

Maintenance Instructions 15
Product Parts Drawing 16
Parts List 17
Warranty 19
Notes 20
Fax/Mail Ordering Form 22

WARNING:

To reduce the risk of serious injury, read the following safety instructions before using the
Elite Inversion System.

1.

Read all warnings posted on the Elite Inversion Syste m .

2.

The Elite Inversion System should only be used after a thorough review of the Owner's Manual.

3.

We recommend that two people be available for assembly of this product.

4.

Do not use the Elite Inversion System alone. Always have a helper availa ble in case a ssistance is needed in recovering
from the decline position.

5.

Make sure that the Pivot Arms are assembled using the sa me hole on both Pivot Arms. Pay close attention to Steps 3 and
4 on page 7.

6.

Make sure that the Pivot Arms are always secured to the pegs on the Main Frame with the Quick Releases.

7.

Make sure that the Pad T ubes are a ssembled with the ends pointed down as directed in STEP 9 on page 9. The ends must
be pointed downward to properly secure the users feet in place during inversion. Improper assembly will allow the users
feet to come loose allowing the user to fall from the inversion table.
Do not use the Elite Inversion System until you have verified your height setting. Failure to use the proper height setting

8.
can result in difficulty recovering from the decline position. See HEIGHT ADJUSTMENT instructions on page 11.
Always make sure that your feet are properly secured in the heel Holder mechanism when using the Elite Inversion

9.

System.

Insert the Ball Pins in the lowest adjustment hole s in the Angle Adjustment Tube s to restrict the movement of the inversion

10.
bed to the lea st amount of inversion angle. Use this setting until you have verified your he ight setting a nd be come familiar
with the Elite Inversion System.
Both Pivot Arms must always be adjusted to the same hole.

11.
You must understand how to recover from the fully inverted position before using the fully inverted position. Read the

12.
RECOVERY FROM LOCKED POSITION section at the bottom of page 14

13.

Always insert the Ball Pins into the same adjustment hole on both sides of the Elite Inversion System.

14.

Do not allow children to use or play on the Elite Inversion System.

15.

Keep small children and pets away from the Elite Inversion Syste m at all times.

16.

The Elite Inversion System should not be used by persons weighing more than 300 lbs.

17.

The Elite Inversion System should not be used by persons over 6 feet 6 inches tall.

18.

It is recommended that you place this exercise equipment on an equipment mat.

19.

Use the Elite Inversion System only on a level surface.

20.

Wear appropriate clothing when exercising; do not wear loose clothing that could become caught in the Elite Inversion

System.

21.

Be sure that there is enough room for the bed to rotate completely.

22.

Use the Elite Inversion System only as described in the manual.

23.

The safety level of the Elite Inversion System can be maintained only if it is examined regularly f or damage and wear.

24.

This equipment is for home use only. It is not for commercial use.

BEFORE using the fully inverted position.

WARNING: Before using this equipment you should consult with your personal physician to see if inversion

equipment is appropriate for you. Do not use this equipment without your physici an's approval. Do not use
this equipment if you have any of the following conditions or ailments:

Extreme obesity
Glaucoma, retinal detachment or conjunctivitis
Pregnancy
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Middle ear infection
High blood pressure, Hypertension, Recent stroke or Transient ischemic attack
Heart or circulatory disorders for which you are being treated
Hiatus hernia or Ventral hernia
Bone weaknesses including Osteoporosis, Unhealed fractures, Medullary pins, or Surgically
implanted orthopedic supports.
Use of anti-coagulants including Aspirin in high doses.

2

CALL US FIRST

THANK YOU FOR PURCHASING THE

Elite Inversion System

To help you get started, we have pre-assembled most of your

Elite Inversion System at the factory with the exception

of those parts left unassembled f or shi pping purposes.

Simply follow the few assembly instructions set forth in this manual.

Within a few minutes you will be getting your body into shape and on your

way to achieving a happier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Friday, 8:00 A.M. - 5:00 P.M., Central Time.

3

BEFORE YOU BEGIN

Thank you for choosing the Elite Inversion

System. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better , look better
and enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The

Elite Inversion

System provides a convenient and simple method

to begin your assault on getting your body in shape
and achieving a happier and healthier life style.
Before reading further, please review the drawing
below and familiarize yoursel f with the parts that are
labeled.
Read this manual carefully before using the

Elite

Inversion System.

Pivot Arm

Although Stamina tries to manufacture its products
with the finest materials and uses the highest
standards of ma nufacturing, occasionally a part that
does not fit, is the incorrect size, or is otherwise
inappropriate is found. Even with the highest
inspection a nd quality controls in place these things
will happen occasionally. Please do not return the
product. For your convenience, Stamina has a
Customer Service Department with a toll-free
number. If a part is missing, does not fit, is the
incorrect size, or is otherwise inappropriate, please
call 1 [phone] (in the U.S.) between 8:00 A.M.
and 5:00 P.M. Central Ti me, Monday through Friday .
Our operators will be able to assist you with your
problem and the parts will be mailed dire ctly to your
house.

Right Shaft Clip

Handrail

Main Frame

Lever

Foam Pad

Footrest

Stand B

Front Frame

Stand A

Height
Adjustment Beam

Heel Holder

Nylon Bed

Handrail

Angle Adjustment Bar
Left Rear Frame
Base Frame

Stand B

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Combination Wrench

Allen Wrench (4mm)

Allen Wrench (6mm)

4

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
end of the bolts, or screws on the circles to check for the corre ct di ameter . Use the small scale to check the
length of the bolts and screws.

3/16" 5/16" 1/2"3/8"1/4"

INCHES

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

59 Bolt, Button Head (M6 x 1 x 35mm) 1
60 Bolt, Button Head (M6 x 1 x 47mm) 1

62 Bolt, Button Head (M8 x 1.25 x 15mm) 4

63 Bolt, Button Head (M8 x 1.25 x 50mm) 2
64 Bolt, Button Head (M8 x 1.25 x 55mm) 2
79 Bolt, Button Head (M10 x 1.5 x 60mm) 2

66 Nylock Nut (M6 x 1) 1
67 Nylock Nut (M8 x 1.25) 2
80 Nylock Nut (M10 x 1.5) 2

68 Washer (M6 x ø16 x 1.5mm Thick) 2
69 Washer (M8) 8
81 Washer (M10) 4

70 Arc Washer (M8) 2
71 Arc Washer (M6) 1

5

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at :

[e-mail]

STEP 1

Insert the LEFT and RIGHT REAR FRAMES(2, 3) into the BASE FRAME(4) and secure with

BOLTS(M8 x 55mm)(64), ARC WASHERS(M8)(70), WASHERS(M8)(69), and NYLOCK
NUTS(M8)(67).

STEP 2

Slide the upper ends of the FRONT FRAME(1) into the Brackets on the LEFT and RIGHT REAR

FRAMES(2, 3) and secure with BOLTS(M10 x 60mm)(79), WASHERS(M10)(81), and NYLOCK
NUTS(M10)(80). Lock the FRONT FRAME(1) in the unfolded position with the LONG BALL PINS(46).

6

ASSEMBLY INSTRUCTIONS

A

B

C

STEP 3

Slide the bottom of the two PIVOT ARMS(91) into the brackets located at e ach side of the MAIN FRAME

(92). Align the de sired hole on the arm with the peg on the bra cket, then insert the peg into the hole to lock

PIVOT ARMS(91) in position. Secure the PIVOT ARMS(91) with the SECURING KNOBS

the

(3/8"-16 x 1/2")(93) on the inner side of the brackets.

PIVOT ARM ADJUSTMENT:

There are three adjustment holes on the PIVOT ARMS(91) allowing you to position the MAIN FRAME(92)
at three different heights. The lowest hole will allow the least amount of inversion angle. The top hole will
allow the greatest amount of inversion angle.

1.

CAUTION:

Use the lowest holes in the PIVOT ARMS(91) until you become familiar with the Elite

Inversion System

2.

Both PIVOT ARMS(91) must be adjusted to the same hole. Trying to adjust the PIVOT

ARMS(91) to different positions could cause da mage to the ma chine, and in jury to the user.

STEP 4

Attach the MAIN FRAME(92) onto the REAR FRAMES(2, 3) by sliding the slots in the ends of the two

PIVOT ARMS(91) into the slots on the REAR FRAMES(2, 3) and secure with the SHAFT CLIPS
(43, 44).

7

ASSEMBLY INSTRUCTIONS

STEP 5

Attach the ANGLE ADJUSTMENT BARS(85) onto the shafts on both sides of the MAIN FRAME(92)
with BOLTS(M8 x 15mm)(62) and WASHERS(M8)(69). Do not tighten the bolts until STEP 6.

STEP 6

Slide one of the SUPPORT SLEEVES(84) onto the left ANGLE ADJUSTMENT BARS(85). Install

SUPPORT SLEEVES(84) onto the shaft on the LEFT FRAME(2) with the SUPPORT SLEEVE(84)

the
above the shaft a s shown in the illustration, and secure with a BOL T(M8 x 15mm)(62) a nd W ASHER(M8)

(69). Insert the PULL PIN(86) into one of the Adjustment Holes in ANGLE ADJUSTMENT BAR(85).

Repeat on the other side. Tighten all the bolts.

8

ASSEMBLY INSTRUCTIONS

STEP 7: Atta ch the FOOTREST(11) onto the HEIGHT ADJUSTMENT BEAM(10) with the adjustment

holes fa cing down. Secure the

NOTE:

The four adjustment holes in the FOOTREST(11) allow the FOOTREST(11) to be attached in
four different positions. Start with one of the center position s and adjust if ne cessary. Use the outer
position if users are taller than average. Use the inner position if users are shorter than average.

FOOTREST(11) in place with the ADJUSTMENT KNOB(12).

STEP 8

Insert the HEEL HOLDER TUBE(13) through the hole on the HEIGHT ADJUSTMENT BEAM(10)
and secure with BOLT(M6 x 47mm)(60), WASHERS(M6 x ø16 x 1.5mm Thick)(68), and NYLOCK

NUT(M6)(66). Place a HEEL HOLDER BRACKET(14) onto a HEEL HOLDER(15), then slide them

onto the

HEEL HOLDER TUBE(13) together. Repeat on other side.

STEP 9

Insert the OUTER P AD TUBE(17) through the hole on the HEIGHT ADJUSTMENT BEAM(10). Insert

INNER PAD TUBE(16) into the OUTER PAD TUBE(17). Align the holes on the INNER PAD

the

TUBE(16), OUTER P AD TUBE(17), and HEIGHT ADJUSTMENT BEAM(10), then bolt them together

BOLT(M6 x 35mm)(59) and ARC W ASHER(M6)(71).

with

WARNING:

The PAD TUBES(16, 17) must be assembled with the ends pointed downward as shown.
The ends must be pointed downward to properly secure the users feet in pla ce during inversion.
Improper a ssembly will allow the user's feet to come loose a nd the user will fall from the

Elite

Inversion System.

9

ASSEMBLY INSTRUCTIONS

STEP 10

Install the HEIGHT ADJUSTMENT BEAM(10) into MAIN FRAME(92) by pulling the SPRING PIN(35)
on the MAIN FRAME(92) and inserting the HEIGHT ADJUSTMENT BEAM(10) a s shown. For added
safety, thread the

WARNING:

LOCKING KNOB(3/8"-16 x 3/4")(36) into back side of the MAIN FRAME(92).

Do not use the Elite Inversion System until you have verified your height setting. Failure
to use the proper height setting can result in difficulty recovering from the decline position.

HEIGHT ADJUSTMENT instructions on page 11.

See

STEP 11

Insert the front ends of the HANDRAILS(5) onto the short tubes on REAR FRAMES(2, 3). Then atta ch
the back ends of the

HANDRAILS(5) with BOLTS(M8 x 50mm)(63) and WASHERS(M8)(69).

10

OPERATIONAL INSTRUCTIONS
GENERAL PRECAUTIONS

Use the lowest holes in the PIVOT ARMS(91) until you become familiar with the Elite Inversion

1.

System.

Do not use the

2.
needed in recovering from the decline position.
Make sure that the

3.
Make sure that the

4.
Make sure that the

5.
and the LOCKING KNOB(36).
Make sure that there is enough room for the bed to rotate completely.

6.

Elite Inversion System alone. Always have a helper available in case assistance is

FOAM PADS(18) and HEEL HOLDERS(15) are holding your feet securely.
HEIGHT ADJUSTMENT BEAM(10) is properly set for your height.

HEIGHT ADJUSTMENT BEAM(10) is held securely by both the SPRING PIN(35)

HEIGHT ADJUSTMENT

The Elite Inversion System is a very sensitive balance device. It responds to very slight changes in
weight distribution. It is very important to make sure that the height adjustment is adjusted properly. Use
the following procedure to set the height adjustment and balance the

Insert the PULL PINS(86) into the second

1.
adjustment holes from the top in the

ANGLE

ADJUSTMENT BARS(85) to restrict the

movement of the
a mount of inversion a ngle. The
should not be inserted into the lowest adjustment
holes in the

NYLON BED(37) to the least

PULL PINS(86)

ANGLE ADJUSTMENT

BARS(85), or the Elite Inversion System may

go into the full inversion position while you are
setting the height adjustment.

2.

Loosen the

LOCKING KNOB(36) under the

MAIN FRAME(92).

3.

Pull the SPRING PIN(35) and use the SCALE

INDICA TION to set the HEIGHT ADJUSTMENT
BEAM(10).

4.

Tighten the LOCKING K NOB(36).

5.

Mount the machine.

6.

Lock your ankle s into the

FOAM P ADS(18) and

HEEL HOLDERS(15).

7.

Lie back with your hands at your sides.

8.

Slowly raise your hands to your che st.

9.

If your feet are higher than your head, dismount
and try a taller setting. If you do not rotate to a
position close to level, dismount and try a shorter
setting.

Elite Inversion System.

NOTE:

The Elite Inversion System should return to the upright position when your hands are below
your waist. If it does not, use a taller setting.

11

OPERATIONAL INSTRUCTIONS
INVERSION ANGLE ADJUSTMENT

There are 11 adjustment holes in the ANGLE

ADJUSTMENT BARS(85) allowing you restrict the

movement of the
by inserting the
adjustment holes.
The top holes will allow the least amount of inversion
angle. The lowe st hole will allow the gre ate st amount of
inversion angle and the
go into the full inversion position.

CAUTION:

1.2.Use the holes near the top in the ANGLE

ADJUSTMENT BARS(85) until you become

familiar with the
Both PULL PINS(86) must be inserted into the sa me
hole in the
Trying to insert the PULL PINS(86) into different
positions could cause damage to the machine, and
injury to the user.

NYLON BED(37) to different angles

PULL PINS(86) into different

Elite Inversion System will

Elite Inversion System.

ANGLE ADJUSTMENT BARS(85).

HEEL HOLDER USE AND ADJUSTMENT

Place your feet on the FOOTREST(11) with your ankle s between the

1.

Button

HEEL HOLDERS(15) a nd FOAM PADS(18).

The HEIGHT ADJUSTMENT BEAM(10) includes a LEVER(23) to

2.
grip and release your feet. Pull the
ankles are securely held between the

LEVER(23) toward you until your

HEEL HOLDERS(15) and

FOAM PADS(18).

To release your feet or relax the grip, pull the LEVER(23) toward you

3.
slightly and press the button on the end of the lever.

THE HANDRAILS

For added convenience, a nd safety , a set of HANDRAILS ha s been added to the Elite Inversion System.
These HANDRAILS are located at both sides of the frame. The HANDRAILS are to help you return to
the upright position from any degree of inversion. If you wish to return to the upright position, and the bed
is moving too slowly , or not moving at all, simply grab the
the upright position.

HANDRAILS a nd pull on them until you return to

12

OPERATIONAL INSTRUCTIONS
USING THE PRO INVERSION SYSTEM

Start by lying fully back on the bed with your hands at your side, or resting on your thighs.

1.
Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate

2.
backward. Stop, or lower your arms to control the downward rotation of the table.

3.

Raise your arms until they are over your head. At this point, the inversion table will be as far back as it
can go.

4.

As you get more comfortable with the use, rock the bed slowly by moving your arms up and down
slowly.

5.

A gentle swinging motion will altern ately put your spine in tra ction a nd compre ssion. This rhythmic type
of traction is used by many hospitals and doctors to treat certain back problems.

6.

It is recommended that the inversion table be used f or five or ten minutes ea ch morning, a nd again ea ch
evening.

7.

Return to the upright position by slowly moving your hands back down to your thighs.

1. 3.

13

4.2.

OPERATIONAL INSTRUCTIONS
SUGGESTIONS FOR USE

Begin slowly: invert with the lea st a mount of inversion a ngle to begin with. Stay inverted only as long as

1.
you are comfortable. Return upright slowly.

2.

Make gra dual change s: increase the a ngle only if it is comfortable. Incre ase the a ngle only one adjustment
hole at a time. Increa se the ti me of use 1-2 minutes up to ten over a period of weeks. Add stretching and
light exercise only after you are comfortable with inversion.

3.

Watch your body: come up slowly, dizziness after a session means you came up to fast. Wait a while
after eating before using table. If you get nauseous, do not f ight it, come up a s soon as you feel queasy .

4.

Keep moving: movement while inverted encourages blood, lymph, a nd spin al fluid circulation and aids
in alignment of bones and organs. Move ment may be accomplished by either rhythmic traction or light
exercise. Do not exercise strenuously while inverted. Limit partial inversion without movement to one or
two minutes. Limit full inversion with no movement to only a few se conds.

5.

Invert regularly: we recommend two or three times a day de pending upon your current condition. T ry to
schedule it for the same times each day.

A.

B. C.

LOCKING THE BED

When the inversion table rotates past the vertical inverted position the bed becomes locked, and will not
return to the upright position in the usual way . The locked position allows you to ha ng straight upside-down
completely free of the bed. This position allows you to enjoy all of the benefits of a ha ndsta nd, with none of
the discomforts, as shown in illustration A. It also allows you to do exercises such as the waistband, as
shown in illustration B.
To get into the locked position, use the top hole in the
If necessary, adjust the HEIGHT ADJUSTMENT BEAM(10) shorter, and then mount and use normally.
When your arms are completely extended above your head, the bed will rotate all the way to the locked
position.

CAUTION: You must understand how to recover from the fully inverted position before using the fully

inverted position. Read the

RECOVERY FROM LOCKED POSITION section below

BEFORE using the fully inverted position.

PIVOT ARMS(6) as described in STEP 3.

RECOVERY FROM LOCKED POSITION

To recover from the locked position, si mply grab the HANDRAILS and pull on them while pushing ba ck on

HEEL HOLDERS(15) with your legs. If you can not reach the HANDRAILS, then you can still

the
recover by grabbing the ba ck of the bed with one hand, the
hands together, as shown in illustration C.

14

REAR FRAME with the other, a nd pulling your

STORAGE

The Elite Inversion System is designed to fold for easy storage. You ca n store

Elite Inversion System as illustrated. Please follow the following process:

your

STEP 1: Loosen LOCKING KNOB(36) and pull out the
SPRING PIN(35). Now, slide the HEIGHT ADJUSTMENT
BEAM(10) into the MAIN FRAME(92) and lock in the lowest

adjustment hole. Refer to illustration 1.

STEP 2: Remove the PULL PINS(86) from the ANGLE
ADJUSTMENT BARS(85). Swing the NYLON BED(37)

down to about the same place as the Rear Frame and lock in
position by inserting the
adjustment holes in the
above the SUPPORT SLEEVE(84). Refer to illustration 2.

PULL PINS(86) into the second

ANGEL ADJUSTMENT BARS(85)

STEP 3: Remove the LONG BALL PINS(46) from the
REAR FRAMES(2, 3). Fold the Front Frame close to the

Rear Frame as Illustration 3 shows. Insert the

LONG BALL
PINS(46) back into the REAR FRAMES(2, 3) to lock the
Elite Inversion System in the folded position.

WARNING:

When folding and unfolding the Elite Inversion System, keep all children away from the

Elite Inversion System a nd make sure your hands are cle ar of any folding or pinch point.

1.

Lowest
Adjustment Hole

3.2.

Insert the PULL PINS(86)
into the second
adjustment holes.

MAINTENANCE

The safety level of the Elite Inversion System can be maintained only if it is examined regularly for
damage and wear.

Check the angle adjustment tube, traction bars, ball pins, pivot arms, cushion bed, heel holders, foam

1.

pads, spring pin, and warning label for
Repla ce da maged a nd worn components immedi ately a nd/or keep the equi pment out of use until repairs

2.

are complete.

da mage and wear.

15

PRODUCT PARTS DRAWING

BACK

FRONT

16

PARTS LIST

DIAGRAM# PART NAME QTY

1 Front Fra me 1
2 Left Rear Frame 1
3 Right Rear Frame 1
4 Ba se Frame 1
5 Handrail 2
10 Height Adjustment Beam 1
11 Footrest 1
12 Adjustment Knob 1
13 Heel Holder Tube 1
14 Heel Holder Bracket 2
15 Heel Holder 2
16 Inner Pad Tube 1
17 Outer Pad Tube 1
18 Foam Pad 2
19 Left Lever Cover 1
20 Right Lever Cover 1
21 Rear Lever Cover 1
22 Corner cap 1
23 Lever 1
26 Claw Spacer 2
31 Spring 1
32 Button 1
33 Hand Grip 1
34 Bushing 2
35 Spring Pin 1
36 Locking Knob (3/8"-16 x 3/4") 1
37 Nylon Bed 1
38 Foam Grip 2
42 Selection Tube Bushing 4
43 Left Shaft Clip 1
44 Right Shaft Clip 1
45 Tension Spring 2
46 Long Ball Pin (
47 Bumper 1
48 Stand A (front left) 2
49 Stand B (front right) 2
50 Hollow Cap 1
51 Oval Plug (20mm x 60mm) 2
52 Dome Plug (22mm) 2
53 Round Plug (22mm) 2
54 Round Plug (25mm) 4
55 Square Plug (38mm x 38mm) 1
56 Support Washer 1
57 Screw, Round Head (M4 x 20mm) 4
58 Bolt, Button Head (M6 x 1 x 15mm) 2
59 Bolt, Button Head (M6 x 1 x 35mm) 1

ø8 x 55mm) 2

17

PARTS LIST

DIAGRAM# PART NAME QTY

60 Bolt, Button Head (M6 x 1 x 47mm) 1
61 Bolt, Button Head (M6 x 1 x 55mm) 2
62 Bolt, Button Head (M8 x 1.25 x 15mm) 5
63 Bolt, Button Head (M8 x 1.25 x 50mm) 5
64 Bolt, Button Head (M8 x 1.25 x 55mm) 2
66 Nylock Nut (M6 x 1) 4
67 Nylock Nut (M8 x 1.25) 5
68 Washer (M6 x
69 Washer (M8) 15
70 Arc Washer (M8) 2
71 Arc Washer (M6) 1
72 Warning Label 1
73 Combination Wrench 1
74 Allen Wrench (4mm) 1
75 Allen Wrench (6mm) 1
76 Manual 1
77 Claw
78 Bolt, Button Head (M6 x 1 x 42mm) 1
79 Bolt, Button Head (M10 x 1.5 x 60mm) 2
80 Nylock Nut (M10 x 1.5) 2
81 Washer (M10) 4
82 Nut (M8 x 1.25) 1
83 Pressing Bar Spacer 1
84 Support Sleeve 2
85 Angle Adjustment Bar 2
86 Pull Pin (
87
91 Pivot Arm 2
92 Main Frame 1
93 Securing Knob (3/8"-16 x 1/2") 2

ø16 x 1.5mm Thick) 10

/ Pressing Bar Assembly 1

ø6 x 40mm) 2

Instruction Video (DVD) 1

18

LIMITED WARRANTY

MODEL 55-1537C

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and 5 years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH PARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilitie s, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not f or personal, family, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd place of purchase and
a brief description of the defect along with your rece ipt to Sta mina Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 [phone]. If the defect is covered under this limited
warranty , you will be reque sted to return the product or part to us for free repair or repla cement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE TO YOU. In the event that the purchaser ma ke s any claim under this

limited warra nty or any implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date a nd place of purchase.

Sta mina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or express warranty given by Sta mina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers a nd limitations of a nd on implied warrantie s and
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal re striction.

19

NOTES

20

NOTES

21

FAX/MAIL ORDERING FORM

Plea se do not return the product. For your convenience, Sta mina has a Customer Service Department with
a toll-free number. Should a part be missing or a defective part found, please call 1 [phone]
(in the U.S.) from 7:30 A.M. to 5:00 P.M. Central T ime, Monday through Thursday a nd 8:00 A.M. to 3:00 P.M.
on Friday or fill out the fax sheet ordering form below and fax it to [phone]. Our Customer Service
Department will be able to assist you with your problem and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

IMPORTANT : We must have your phone number in order to process the order!

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

IMPORTANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

MAIL

P.O. Box 1071

EXAMPLE:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1