Page 1
Owner's
Manual
WARNING
Exercise can present a health
risk. Con sult a physici an
before beginning any exercise
program with this equi pment.
If you feel faint or dizzy ,
immediately discontinue use
of this equi pment. Serious
bodily injury can occur if this
equipment is not a ssembled
and used corre ctly. Serious
bodily injury can also occur if
all in structions are not
followed. Kee p others a nd
pets away from equi pment
when in use. Always make
sure all bolts a nd nuts are
tightened prior to e ach use.
Follow all safety instructions in
this manual.
CAUTION:
Weight on this product should not exceed 250 lbs.
This Product is Produced Exclusively by
2040 N. Alliance, Springfield, MO 65803
Customer Service Number
1 (800) 375-7520
www.staminaproducts.com
2010, 06
When calling f or parts or
service, ple ase spe cify the
following number.
45-1002B
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
2009 Stamina Products, Inc.
Page 2
TABLE OF CONTENTS
Page Page
Safety Instructions 2
Before You Begin 4
Hardware Illustrations 5
Assembly Instructions 6
Using The Electronics Meter 8
Treadmill Adjustments 9
Maintenance 10
Storage 11
Product Parts Drawing 12
Parts List 13
Warranty 14
Fax/Mail Ordering Form 15
SAFETY INSTRUCTIONS
WARNING:
1.
Read all warnings posted on the InMotion
Read this Owner's M anual and follow it carefully before using the InMotionTM II Treadmill. Make
2.
sure that it is properly assembled and tightened before use.
We recommend that two people be available for assembly of this product.
3.
Keep children away from the InMotionTM II Treadmill. Do not allow children to use or play on the
4.
InMotionTM II Treadmill. Keep children and pets away from the InMotionTM II Treadmill when it is
in use.
It is recommended that you place this exercise equipment on an equipment mat.
5.
Set up and operate the InMotionTM II Treadmill on a solid level surface. Do not position the InMotion
6.
II Treadmill on loose rugs or uneven surfaces.
Inspect the InMotionTM II Treadmill for worn or loose components prior to use. Tighten/replace any
7.
loose or worn components prior to using the InMotionTM II Treadmill.
Keep fingers clear of all pinch points when folding and unfolding the InMotionTM II Treadmill.
8.
When f olding the InMotionTM II T readmill f or storage, ma ke sure that Ba se Frame Assembly is
9.
locked securely in the folded position by the Spring Pin.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
10.
feel faint, dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
11.
Always choose the workout which be st fits your physical strength a nd flexibility level. Know your
12.
limits and train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the InMotionTM II Treadmill.
13.
Never exercise in bare feet or sock s; always wear correct footwear, such as running, walking, or
14.
crosstraining shoes. Be sure that they fit well, provide foot support and feature non-skid rubber soles.
Be careful to maintain your balance while using, mounting, dismounting, or assembling the InMotion
15.
II Treadmill, loss of balance may result in a fall and serious bodily injury.
The InMotionTM II Treadmill should not be used by persons weighing over 250 pounds.
16.
The InMotionTM II Treadmill should be used by only one person at a time.
17.
The InMotionTM II T readmill is f or con sumer use only . It is not f or use in public or semi public
18.
facilities.
To reduce the ris k of serious in jury, re ad the following Safety In structions before
using the
InMotionTM II Treadmill.
TM
II Treadmill.
TM
TM
WARNING:
Before starting any exercise or conditioning program you should consult with your personal
physician to see if you require a complete physical exam. This is especially important if you
are over the age of 35, have never exercised bef ore, are pregn ant, or suf fer from a ny
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.
2
Page 3
CALL US FIRST
THANK YOU FOR PURCHASING THE
InMotionTM II Treadmill
To help you get started, we have pre-assembled most of your
InMotionTM II Treadmill at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
Within a few minutes you will be getting your body into shape and on your
way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 (800) 375-7520
Monday - Friday, 8:00 A.M. - 5:00 P.M., Central Time.
3
Page 4
BEFORE YOU BEGIN
Thank you f or choosing the InMotion
TM
II
Treadmill. We take gre at pride in producing this
quality product and hope it will provide many hours
of quality exercise to make you feel better, look better
and enjoy life to its fullest.
Yes, it's a proven fa ct that a regular exercise
program ca n i mprove your physical a nd mental
health. Too often, our busy life styles limit our ti me
and opportunity to exercise. The
InMotionTM II
Treadmill provides a convenient and simple method
to begin your assault on getting your body in shape
and achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Re ad this ma nual carefully bef ore using the
InMotionTM II Treadmill.
Meter
Although Stamina tries to manufacture its products
with the f inest materi als and use s the highe st
standards of manufacturing, occasionally a part that
does not f it, is the incorre ct size, or is otherwise
inappropriate is f ound. Even with the highe st
inspection and quality controls in place these things
will happen occasionally. Please do not return the
product. For your convenience, Sta mina has a
Customer Service Department with a toll-free
number. If a part is missing, doe s not f it, is the
incorrect size, or is otherwise in appropriate, please
call 1 (800) 375-7520 (in the U.S.) between 8:00 A.M.
and 5:00 P.M. Central Time, Monday through Friday.
Our operators will be a ble to a ssist you with your
problem and the parts will be mailed directly to your
house.
U-Shaped Handrail
Left Upright
Flywheel
Upright Support
Moving Wheel
Spring Pin
Base Frame
Right Upright
Walking Belt
Side Molding
Adjustment
Bracket
Bumper Stand
THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Wrench
Allen Wrench (4mm)
4
Page 5
HARDWARE IDENTIFICATION CHAT
This chart is provided to help identify the hardware used in the assembly process.
After unpacking the unit, open the hardware bag and make sure that you have the following items:
3/16" 5/16" 1/2"3/8"1/4"
INCHES
11/2021/2 31/2 41/2 51/2 61/2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
MILLIMETERS
6 8 10 12
Place washers, the end of bolts or screws on the circle s to che ck for the
correct size. Use the small scale to check the sizes of bolts and screws.
NOTICE: The length of all kinds of screws a nd bolts are not included
themselves head, except the flat head screws and bolts.
Part No. and Description Qty
38 Bolt, Hex Head (M10 x 1.5 x 20mm) 4
in.
mm.
length
length
NOTE:
39 Bolt, Hex Head (M12 x 1.75 x 70mm) 2
40 Bolt, Button Head (M6 x 1 x 15mm) 2
44 Arc Washer (M6) 2
47 Washer (M10) 4
48 Washer (M12) 2
1. Some of the hardware items listed may be attached to other parts.
2. Bolt length is measured from the bottom of the bolt head to the end of the bolt.
5
Page 6
ASSEMBLY INSTRUCTIONS
Place all parts from the box in a cle ared area and position them on the floor in front of you. Re move all
packing materials from your area and place them back into the box. Do not dispose of the packing materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part ple ase
call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at:
parts@staminaproducts.com
Sensor Wire
STEP 1
NOTE: The LEFT UPRIGHT(2) is the one with the Sensor Wire.
Attach the
LEFT a nd RIGHT UPRIGHTS(2, 3) to the UPRIGHT SUPPORT(4) with HEX BOLTS
(M10 x 20mm)(38) and WASHERS(M10)(47).
STEP 2
Slide the SPRING(7) onto the SPRING PIN(6). Insert the threaded end of the SPRING PIN(6) through
the collar on the
RIGHT UPRIGHT(3) and screw the BALL KNOB(8) onto the thread end of the SPRING
PIN(6). Tighten the BALL KNOB(8) as tight as you can by hand.
6
Page 7
ASSEMBLY INSTRUCTIONS
STEP 3: Place the BASE FRAME(1) between the LEFT and RIGHT UPRIGHTS(2, 3) and secure
with
HEX BOLTS(M12 x 70mm)(39) and WASHERS(M12)(48). DO NOT TIGHTEN COMPLETELY.
STEP 4: Secure the U-SHAPED HANDRAIL(5) onto the LEFT and RIGHT UPRIGHTS(2, 3) with
BUTTON HEAD BOLTS(6mm x 15mm)(40) and ARC WASHERS(M6)(44). Connect the UPPER
EXTENSION WIRE(28) to the LOWER EXTENSION WIRE(29).
STEP 5: Go back and tighten HEX BOLTS(M12 x 70mm)(39) in STEP 2. Conne ct the LOWER
EXTENSION WIRE(29) located on the LEFT UPRIGHT(2) to the SENSOR WIRE(30). In sert the
PULL PIN(9) through the RIGHT UPRIGHT(3) and BASE FRAME(1) to lock the BASE FRAME(1) in
position.
STEP 6: Install two "AA" batteries into the METER(26), two batteries included. See page 8 for detailed
battery installation instructions. Slide the
Connect the UPPER EXTENSION WIRE(28) to the METER(26).
METER(26) onto the plate on the U-SHAPED HANDRAIL(5).
STEP 7: Attach the BUMPER STANDS(22) to the bottom of the BASE FRAME(1).
NOTE: The BUMPER STANDS(22) may be stored on the end of the BASE FRAME(1) to increase the
angle of the treadmill and reduce the walking resistance. See page 10 for details on adjusting the walking
resistance.
7
Page 8
USING THE ELECTRONIC METER
POWER ON :
POWER OFF :
MODE / CLEAR BUTTON:
Walking Belt movement or push the button.
Automatic shut off after 4 minutes of inactivity.
Press and release to select functions.
Press and hold for three seconds to reset all
functions to zero.
FUNCTIONS:
SCAN:
TIME:
SPEED:
Automatically scans TIME, SPEED, DISTANCE, and CALORIES in sequence with a change
every four seconds. Press and release the button until "
to SCAN.
Displays the time, from 1 sec. up to 99:59 minutes.
Displays the current speed, from zero to 999.9 Mile/Hr.
" appears on the display and points
DISTANCE:
CALORIES:
Displays the distance, from zero to 99.99 miles.
Displays the calorie consumption, from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a comparison
between workouts on this unit.
HOW TO INSTALL AND REPLACE BATTERY:
Open the Battery Door on the back of the meter.
1.
The meter operates with two AA batteries, two batterie s included.
2.
Refer to the illustration to install or replace the batteries.
NOTE:
Do not mix a new battery with an old battery.
1.
Use the same type of battery. Do not mix a n alkaline battery with
2.
another type of battery.
Rechargeable batteries are not recommended.
3.
AA Batteries
8
Page 9
TREADMILL ADJUSTMENTS
The basic idea behind the manual treadmill is to have the belt running on a treadmill board and between two
rollers so that the belt will move without much effort. In order for the belt to run smoothly, there are a few
points that need to be noted.
BELT ALIGNMENT
The belt must be in the center of the tre admill to prevent it from rubbing against the flywheels. If the belt
rubs a flywheel, it will be difficult to keep the belt moving and eventually damage the edge of the belt.
The treadmill has belt guide s welded to the bottom of the tre admill frame that move the belt toward the
center of the treadmill. However, the rear roller must be properly aligned with the treadmill frame and front
roller if the belt is to remain centered on the treadmill.
The bolts in the rear of the treadmill (one on the left and the other on the right) adjust the alignment of the
rear roller as well as the tension of the belt.
The belt will run to the side of the loose rear bolt.
Hint:
Eyeball the re ar roller to ma ke sure both the right side a nd the left side of the roller are the sa me
distance from the ba ck edge of the tre admill. Use the
adjustments. Turn the bolts Clockwise to tighten and Counter-Clockwise to loosen.
4mm ALLEN WRENCH to ma ke the se
BELT DRIFTING LEFT
Turn the left screw 1/4 turn CLOCKWISE and the right screw 1/4 turn
COUNTER-CLOCKWISE, then walk on the treadmill. Repeat if needed.
BELT DRIFTING RIGHT
Turn the left screw 1/4 turn COUNTER-CLOCKWISE and the right screw
1/4 turn CLOCKWISE, then walk on the treadmill. Repeat if needed.
LEFT
ADJUSTMENT
RIGHT
ADJUSTMENT
NOTE:
When you believe the WALKING BELT is centered, use the tre admill for three (3) minute s to verify the
WALKING BELT won't drift to one side. If the WALKING BELT continues to drift, the floor may not be level.
Rotate the treadmill 90 degrees or move the treadmill to another location.
BELT TENSION
The belt should be tight and not lying on the treadmill board. If the belt is too loose, the belt will slip on the
front roller and you will notice a jerky movement when you walk on the treadmill. If the belt is too tight, the
edges of the belt will begin to curl and more effort will be required to move the belt. Excessive belt tension
can also damage the bearings in the rollers. The bolts in the rear of the treadmill (one on the left and the
other on the right) adjust the tension of the belt as well as the alignment of the rear roller.
BELT TOO LOOSE: Use the 4mm ALLEN WRENCH to tighten the bolts in the re ar of the treadmill.
Tighten both rollers 1/4 turn at a time until the belt stops slipping on the front roller.
BELT TOO TIGHT: Use the 4mm ALLEN WRENCH to loosen the bolts in the re ar of the tre admill.
Loosen both rollers 1/2 turn at a time until the belt begins to slip on the front roller. Then use the procedure
above to tighten the belt.
9
Page 10
TREADMILL ADJUSTMENTS
WALKING RESISTANCE
The walking resistance or effort needed to push the treadmill belt can be adjusted by changing the incline
angle. This treadmill has two adjustment positions.
Highest Resistance
The BUMPER STANDS(22) are attached to
the bottom of the treadmill.
Remove (unscrew) the BUMPER STANDS(22)
from the bottom of the treadmill and store them
Lowest Resistance
in the end of the treadmill.
NOTE:
Since this is a new ma chine, you may need some ti me to get used to wal king on the treadmill and to
1.
break it in.
If the walking resistance is still too high, check the
2.
The belt resistance can be reduced by adding silicone lubricant between the belt and the board. Wipe
3.
the board under the belt with a cloth and spray or spread silicone lubricant on the board under the belt.
BELT TENSION.
MAINTENANCE
The safety a nd integrity de signed into the InMotion
InMotionTM II Treadmill is regularly examined for damage and wear. Special attention should be given to
the following:
Clean the exposed surfaces of the walking belt and the board with an absorbent cloth.
1.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
2.
Verify that the Spring Pin is pre sent a nd functioning properly . Verify that the Ball Knob is se curely
3.
attached to the Spring pin. Repair or replace parts as necessary.
Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts. Tighten
4.
loose nuts and bolts.
Verify that the Warning La bel is in pla ce and e asy to re ad. Call Sta mina Products i mmediately
5.
(1-800-375-7520) for a replacement Warning Label if the Warning Label is missing or damaged.
Worn or damaged components shall be replaced immediately or the
6.
from service until repair is made.
7.
Only Stamina Products supplied components shall be used to maintain/re pair the
Treadmill.
8.
Keep your InMotion
9.
If the
WALKING BELT(17) does not move e asily, lubricate the BOARD(18) under the WALKING
TM
II Treadmill clean by wiping with an absorbent cloth after use.
BELT(17) with Silicone Lubricant.
TM
II T readmill can only be maintained when the
InMotionTM II Treadmill removed
InMotionTM II
10
Page 11
STORAGE
To store the
1.
To avoid damage to the electronics meter, remove the batteries before storing the
2.
for one year or more.
Follow the following process to fold The
3.
a.
Remove the PULL PIN(9) to unlock the BASE FRAME ASSEMBLY(1).
b.
Fold up the BASE FRAME ASSEMBLY(1). Pull out the BALL KNOB(8) on the spring pin and
release to lock the
CAUTION: Make sure the Base Frame Assembly is locked securely in folded position by the spring pin.
c.
Store the
4.
Move the
the
U-SHAPED HANDRAIL(6) to move the InMotionTM II Treadmill.
InMotionTM II Treadmill simply keep it in a clean dry place.
InMotionTM II Treadmill
InMotionTM II Treadmill as illustrated for easy storage.
BASE FRAME ASSEMBLY(1) in upright position.
PULL PIN(9) by inserting the PULL PIN(9) back into the hole in the RIGHT UPRIGHT(3).
InMotionTM II Treadmill with the moving wheels on the UPRIGHT SUPPORT(4). Grasp
UNFOLD THE InMotionTM II Treadmill
Remove the PULL PIN(11) from the RIGHT UPRIGHT FRAME(3).
a.
b.
Pull out the BALL KNOB(10) on the spring pin and unfold the BASE FRAME ASSEMBLY(1).
c.
Lock the BASE FRAME ASSEMBLY(1) in position by inserting the PULL PIN(11) through the RIGHT
UPRIGHT FRAME(3) and BASE FRAME(1).
11
Page 12
PRODUCT PARTS DRAWING
FRONT
Belt Guides
12
BACK
Page 13
PARTS LIST
DIAGRAM# PART NAME QTY
1 Base Frame 1
2 Left Upright 1
3 Right Upright 1
4 Upright Support 1
5 U-Shaped Handrail 1
6 Spring Pin 1
7 Spring 1
8 Ball Knob 1
9 Pull Pin 1
10 Front Roller /w Flywheels 1
11 Front Shaft 1
12 Bearing (6000zz) 4
13 Plastic Washer (M10) 4
14 Rear Roller 1
15 Rear Shaft 1
16 Adjustment Bracket 2
17 Walking Belt 1
18 Board 1
19 Left Side Molding 1
20 Right Side Molding 1
21 Round Cap (38mm) 2
22 Bumper Stand 2
23 Moving Wheel 2
24 Foam Grip 2
25 Long Foam Grip 2
26 Meter 1
27 Grommet Plug 4
28 Upper Extension Wire 1
29 Lower Extension Wire 1
30 Sensor Wire 1
31 Magnet 1
32 Screw Sleeve 6
33 Round Plug (25mm) 2
34 Rectangular Plug (25mm x 50mm) 2
35 Screw, Flat Head (M3.5 x 15mm) 2
36 Screw, Flat Head (M5 x 25mm) 6
37 Bolt, Hex Head (M6 x 1 x 55mm) 2
38 Bolt, Hex Head (M10 x 1.5 x 20mm) 4
39 Bolt, Hex Head (M12 x 1.75 x 70mm) 2
40 Bolt, Button Head (M6 x 1 x 15mm) 2
41 Bolt, Button Head (M6 x 1 x 70mm) 2
42 Bolt, Button Head (M8 x 1.25 x 15mm) 2
43 Nylock Nut (M6 x 1) 2
44 Arc Washer (M6) 2
45 Washer (M6) 6
46 Washer (M8) 2
47 Washer (M10) 4
48 Washer (M12) 2
49 Warning Label 1
50 Wrench 1
51 Allen Wrench (4mm) 1
52 Owner's Manual 1
13
Page 14
LIMITED WARRANTY
MODEL 45-1002B
WARRANTY
Stamina Products, Inc. warra nts that this product will be free from defe cts in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts a nd one year on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT
APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR T O ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA
PRODUCTS, INC. Commerci al use include s use of the product in athletic clubs, he alth clubs, spa s,
gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and
a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springfield
Missouri, USA, 65801-1071 or call us at 1 (800) 375-7520. If the defe ct is covered under this li mited
warranty, you will be requested to return the product or part to us for free repair or replacement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT T O THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE TO YOU. In the event that the purchaser makes any claim under this
limited warranty or any implied warranty, the Warrantor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warra nty registration card is not required f or warra nty coverage, but is merely a way of
establishing the date and place of purchase.
Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT , CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warranty
gives you spe cific legal rights, a nd you may also have other legal rights which vary from state to state.
ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY.
The laws in some jurisdiction s restrict the rights of ma nufacturers and distributors of con sumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be applicable, the foregoing disclaimers and limitations of and on implied warranties and
consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.
14
Page 15
FAX/MAIL ORDERING FORM
Please do not return the product. For your convenience, Stamina has a Customer Service Department with
a toll-free number . Should a part be missing or a defe ctive part f ound, ple ase call 1 (800) 375-7520
(in the U.S.) between 8:00 A.M. and 5:00 P.M. Central Time, Monday through Friday or fill out the fax sheet
ordering form below and fax it to (417) 889-8064. Our Customer Service Department will be able to assist
you with your problem and the part will be mailed directly to your house.
TELEPHONE
CUSTOMER SERVICE
Tel: 1 (800) 375-7520
FAX
CUSTOMER SERVICE
Fax: (417) 889-8064
ONLINE
CUSTOMER SERVICE
parts@staminaproducts.com
www.staminaproducts.com
STAMINA PRODUCTS, INC.
ATTN: Customer Service
Springfield, MO. 65801-1071
Detach and Mail or Fax the Form Below
Stamina Products, Inc.
P.O. Box 1071
Springfield, MO 65801-1071
Mr./Ms:
Address: Apt. #:
City: State: Zip Code:
IMPORTANT : We must have your phone number in order to process the order!
Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:
IMPORTANT : Before filling out the form below make sure you have the right information.
Refer to the parts list to make sure you're ordering the right parts!
MAIL
P.O. Box 1071
EXAMPLE:
PART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1
Loading...