Exercise can present a
h e a l th r i sk . Co n su l t a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
dis c o n t i nue use of this
equipment. Serious bodily
in j u ry c a n occ u r if th is
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all in str uct ion s a re not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.
Product May Vary Slightly From Pictured.
CAUTION:
Weight on this product should not exceed 250 lbs.
1. Read all warnings and cautions posted on the STAMINA
2. The STAMINA
Manual.
3. We recommend that two people be available for assembly of this product.
4. Keep children away from the STAMINA
on the STAMINABench when it is in use.
5. It is recommended that you place this exercise equipment on an equipment mat.
6. Set up and operate the STAMINA
STAMINA
7. Make sure that adequate space is available for access to and around the STAMINA
Bench.
8. Before using, inspect the STAMINA
tighten or replace any worn or loose components prior to use.
9. C onsult a p h y s i c i a n prior to co m m encing an ex e r cise progr a m a n d follow his / h e r
recommendations in developing your tness program. If at any time during exercise you feel faint,
dizzy, or experience pain, stop and consult your physician.
10. Always choose the workout which best ts your physical strength and exibility level. Know your
limits and train within them. Always use common sense when exercising.
11. Do not wear loose or dangling clothing while using the STAMINA
12. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or
cross training shoes that t well, provide foot support, and feature non-skid rubber soles.
13. Be careful to maintain your balance while using, mounting, dismounting, or assembling the
STAMINA
14. The STAMINA
15. The STAMINA
16. The STAMINA
facilities.
This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is
especially important if you are over the age of 35, have never exercised before,
are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in bodily injury and property damage.
To reduce the risk of serious injury, read the following Safety Instructions
│X -
before using the STAMINA
│X -
Hyper Bench should only be used after a thorough review of the Owner’s
│X -
Hyper Bench. Keep children and pets away from the STAMINA│X - Hyper
│X -
Hyper Bench on a solid level surface. Do not position the
│X -
Hyper Bench on loose rugs or uneven surfaces.
Hyper Bench.
│X -
Hyper Bench.
│X -
Hyper Bench. Do not allow children to use or play
│X -
│X -
Hyper Bench for worn or loose components, and securely
│X -
Hyper Bench.
│X -
Hyper Bench, loss of balance may result in a fall and serious bodily injury.
│X -
Hyper Bench should not be used by persons weighing over 250 pounds.
│X -
Hyper Bench should be used by only one person at a time.
│X -
Hyper Bench is for consumer use only. It is not for use in public or semipublic
2
Hyper
Page 3
Call Us First
www.staminaproducts.com
1(800) 375-7520
Customer Service
THANK YOU FOR PURCHASING THE
STAMINA│X - Hyper Bench
To enact your warranty, please register your product
by going to register.staminaproducts.com
Your STAMINA│X - Hyper Bench does require assembly.
Please follow the assembly steps set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
1 (800) 375-7520
ONLINE
CUSTOMER SERVICE
customerservice@staminaproducts.com
www.staminaproducts.com
TELEPHONE
CUSTOMER SERVICE
Tel: 1 (800) 375-7520
3
FAX
CUSTOMER SERVICE
Fax: (417) 889-8064
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springeld, MO. 65801-1071
Page 4
BEFORE YOU BEGIN
│X -
Thank you for choosing the STAMINA
Be nch. We take g reat pride in producing this
quality product and hope it will provide many hours
of quality exercise to make you feel better, look
better, and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The STAMINA│X - Hyper
Bench provides a convenient and simple method
to begin your journey of getting your body in shape
and achieving a happier and healthier lifestyle.
Before r e ading fu r t h er, p lease rev i e w the
drawing below and familiarize yourself with the
parts that are labeled.
Read this manual carefully before using the
STAMINA│X - Hyper Bench.
Hyper
Although Stamina constructs its products with
the nest materials and uses the highest standards
of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your STAMINA│X - Hyper
Bench, please do not return the product. Contact
us FIRST!
If a part is missing or defective, please go to
staminaproducts.com under the Service section
and order the part needed, or call us toll free
at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to assist you from 7:30
A.M. to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00 A.M. to 3:00 P.M. (Central
Time) on Friday.
Be sure to have the name and model number of
the product available when you contact us.
Cushion Post
Main Support
Foam Roll
Rear Stabilizer
Oval Endcap
Cushion
Securing
Knob
Foam Grip
Right Handrail
Adjustment Knob
Caution Label
Front Stabilizer
Oval Endcap
Front Support
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench (2 pieces)
4
Page 5
EQUIPMENT WARNING, CAUTION & NOTICE LABELS
This chart is provided to help identify the warning, caution, and notice labels on the STAMINA
- Hyper Bench. Please take a moment to familiarize yourself with all of the warning, caution, and
notice labels.
│X
Label is larger than actual size
CAUTION LABEL(33)C1
5
Page 6
HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
length
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.
Part Number and Description Qty
18 Bolt, Hex Head (M10 x 1.5 x 70mm) 3
19 Bolt, Hex Head (M10 x 1.5 x 60mm) 2
20 Bolt, Hex Head (M10 x 1.5 x 20mm) 6
21 Bolt, Hex Head (M6 x 1 x 15mm) 4
23 Washer (M10) 16
24 Washer (M6) 4
25 Nylock Nut (M10 x 1.5) 5
6
Page 7
ASSEMBLY INSTRUCTIONS
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Service section and order the part needed,
e-mail us at customerservice@staminaproducts.com, or call us toll free at 1-800-375-7520 (in the
U.S.). Our Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central
Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
STEP 1
Insert the REAR STABILIZER(1) into the MAIN SUPPORT(3) and secure with HEX BOLTS(M10x1.5x20mm)
(20), and WASHERS(M10)(23). Press a NUT CAP(M10)(26) onto each bolt head of HEX BOLTS
(M10x1.5x20mm)(20).
STEP 2
Insert the FRONT STABILIZER(2) into the FRONT SUPPORT(4) and secure with HEX BOLTS(M10x1.5x20mm)
(20), and WASHERS(M10)(23). Press a NUT CAP(M10)(26) onto each bolt head of HEX BOLTS
(M10x1.5x20mm)(20).
STEP 3
Attach the FRONT SUPPORT(4) to the MAIN SUPPORT(3) with HEX BOLT(M10x1.5x70mm)(18),
WASHERS(M10)(23), and NYLOCK NUT(M10x1.5)(25). Press the NUT CAPS(M10)(26) onto the bolt head
of HEX BOLT(M10x1.5x70mm)(18) and NYLOCK NUT(M10x1.5)(25). Lock the FRONT SUPPORT(4) in
position by inserting the LOCKING PIN(15) through the bracket on the MAIN SUPPORT(3) and the FRONT
SUPPORT(4).
FRONT
REAR
7
Page 8
ASSEMBLY INSTRUCTIONS
STEP 4
NOTE: There are two sets of holes in the MAIN SUPPORT(3) which allows you to attach the FOAM ROLL
POST(8) to two different positions. Try the upper position rst.
Attach the FOAM ROLL POST(8) to the MAIN SUPPORT(3) with the SUPPORT PLATE(11), HEX
BOLTS (M10x1.5x70mm)(18), WASHERS(M10)(23), and NYLOCK NUTS(M10x1.5)(25). Press the NUT
CAPS(M10)(26) onto the bolt heads of HEX BOLTS(M10x1.5x70mm)(18) and NYLOCK NUTS(M10x1.5)
(25).
STEP 5
NOTE: There are two adjustment holes in the FOAM ROLL POST(8). These adjustment holes allow
users to adjust the position of the FOAM ROLLS(16). Try the upper hole rst.
Slide a FOAM ROLL(16) onto the SUPPORT TUBE(9). Insert the other end of the SUPPORT TUBE(9)
through the upper hole in the FOAM ROLL POST(8). Slide another FOAM ROLL(16) over the protruding
end of the SUPPORT TUBE(9).
8
Page 9
ASSEMBLY INSTRUCTIONS
STEP 6
Insert the CUSHION POST(5) into MAIN SUPPORT(3) and lock in position with the ADJUSTMENT
KNOB(13). For added safety, thread the SECURING KNOB(14) into the right side of the MAIN SUPPORT(3).NOTE: The pin of the ADJUSTMENT KNOB(13) must be inserted into one of the adjustment holes in the
CUSHION POST(5). The ADJUSTMENT KNOB(13) and SECURING KNOB(14) must be screwed in tightly to ensure that the CUSHION POST(5) will t securely in the MAIN SUPPORT(3).
STEP 7
Attach the LEFT and RIGHT HANDRAILS(6, 7) to both sides of the CUSHION POST(5) with HEX
BOLTS(M10x1.5x60mm)(19), WASHERS(M10)(23), and NYLOCK NUTS(M10x1.5)(25). Press the NUT
CAPS(M10)(26) onto the bolt heads of HEX BOLTS(M10x1.5x60mm)(19) and NYLOCK NUTS(M10x1.5)
(25).
STEP 8
Attach the CUSHION(12) to the CUSHION POST(5) with HEX BOLTS(M6x1x15mm)(21) and WASHERS
(M6)(24).
9
Page 10
OPERATIONAL INSTRUCTIONS
CUSHION HEIGHT ADJUSTMENT
To adjust the height of the CUSHION(12), loosen but do
not remove the SECURING KNOB(14). Loosen and pull
the ADJUSTMENT KNOB(13), slide the CUSHION(12) to
the desired position, and secure with the ADJUSTMENT
KNOB(13). Tighten the ADJUSTMENT KNOB(13) and
SECURING KNOB(14).
NOTE: The pin of the ADJUSTMENT KNOB(13) must be
inserted into one of the adjustment holes in the
CUSHION POST(5). The ADJUSTMENT KNOB(13)
and SECURING KNOB(14) must be screwed in tightly
to ensure that the CUSHION POST(5) will t securely
in the MAIN SUPPORT(3).
10
Page 11
STORAGE
│X -
1. To store the STAMINA
2. Use two people to lift from the LEFT and RIGHT HANDRAILS(6, 7) and REAR STABILIZER(1) to
move the STAMINA│X - Hyper Bench.
3. Follow the process below to fold the STAMINA│X - Hyper Bench as illustrated for easy storage.
a. Loosen but do not remove the SECURING KNOB(14). Loosen and pull the ADJUSTMENT KNOB(13),
slide the CUSHION(12) to the lowest position. Then lock in position by tightening the ADJUSTMENT KNOB(13) and SECURING KNOB(14).
b. Remove the LOCKING PIN(15) from the MAIN SUPPORT(3) to fold the FRONT SUPPORT(4). Store
the LOCKING PIN(15) in the hole in the FRONT SUPPORT(4).
c. The STAMINA
│X -
Hyper Bench, simply keep it in a clean dry place.
Hyper Bench should appear as shown in illustration B after folded.
A.
B.
MAINTENANCE
The safety and integrity designed into the STAMINA
STAMINA│X - Hyper Bench is regularly examined for damage and wear. Special attention should be
given to the following:
1. Verify that the CAUTION LABEL(33) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement CAUTION LABEL(33) if it is missing or damaged.
2. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Securely tighten loose nuts and bolts.
4. Worn or damaged components shall be replaced immediately or the STAMINA
removed from service until repair is made.
5. Only Stamina Products supplied components shall be used to maintain/repair the STAMINA│X - Hyper
Bench.
6. Keep your STAMINA│X - Hyper Bench clean by wiping it off with an absorbent cloth after use.
│X -
Hyper Bench can only be maintained when the
│X -
Hyper Bench
11
Page 12
CONDITIONING GUIDELINES
How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Remember to follow these essentials:
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically t.
If you feel dizzy or lightheaded you should slow down or stop exercising.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or
three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second
heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.
Target Heart Rate Zone Estimated by Age*
Age
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate)
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
Average Maximum
Heart Rate 100%
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute
wrist pulse
* For cardiorespiratory training benefits, the American College of Sports Medicine recommends
working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the
maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate
12
Page 13
WARM-UP and COOL-DOWN
Warm-Up
Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that
raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place.
Stretching
strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.
The purpose of warming up is to prepare your body for exercise and to minimize injuries.
Stretching while your muscles are warm after a proper warm-up and again after your
Suggested Stretching Exercises
Lower Body Stretch
Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
While sitting on the oor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Torso Pulls
While sitting on the oor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.
Bent Over Leg Stretch
Stand with feet shoulder-
width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.
Remember to always check with your physician before starting any exercise program.
Cool-Down
state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be
completed after each strength training session.
The purpose of cooling down is to return the body to its normal, or near normal, resting
13
Page 14
PRODUCT PARTS DRAWING
FRONT
BACK
14
Page 15
PARTS LIST
1 Rear Stabilizer 1
2 Front Stabilizer 1
3 Main Support 1
4 Front Support 1
5 Cushion Post 1
6 Left Handrail 1
7 Right Handrail 1
8 Foam Roll Post 1
9 Support Tube 1
10 Foot Plate 2
11 Support Plate 1
12 Cushion 1
13 Adjustment Knob 1
14 Securing Knob 1
15 Locking Pin 1
16 Foam Roll 2
17 Foam Grip 2
18 Bolt, Hex Head (M10 x 1.5 x 70mm) 3
19 Bolt, Hex Head (M10 x 1.5 x 60mm) 2
20 Bolt, Hex Head (M10 x 1.5 x 20mm) 6
21 Bolt, Hex Head (M6 x 1 x 15mm) 4
22 Screw, Flat Head (M4 x 15mm) 4
23 Washer (M10) 16
24 Washer (M6) 4
25 Nylock Nut (M10 x 1.5) 5
26 Nut Cap (M10) 16
27 Oval Endcap (30mm x 70mm) 4
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on
the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL
NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health
clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the
product's use is in furtherance of a prot making enterprise, and all other use which is not for personal,
family, or household purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springeld Missouri, USA, 65801-1071, or email us at customerservice@staminaproducts.com, or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH
OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any
implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,
at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed
warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.
Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS
OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This
warranty gives you specic legal rights, and you may also have other legal rights which vary from state to
state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.
16
Page 17
NOTES
17
Page 18
TO CONTACT CUSTOMER SERVICE
TO CONTACT CUSTOMER SERVICE
For your convenience, Stamina’s customer service r epresentatives can be reached by email at customerservice@
staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday
through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.
ONLINE
CUSTOMER SERVICE
customerservice@staminaproducts.com
www.staminaproducts.com
TELEPHONE
CUSTOMER SERVICE
Tel: 1 (800) 375-7520
FAX
CUSTOMER SERVICE
Fax: (417) 889-8064
STAMINA PRODUCTS, INC.
P.O. Box 1071 Springeld, MO. 65801-1071
MAIL
ATTN: Customer Service
Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com
TO REGISTER YOUR PRODUCT
TO REGISTER YOUR PRODUCT
To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model
number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your
product) ready.
If you don’t have internet access, you can call customer service at 1-800-375-7520, or ll out and mail the product registration
form below to Stamina Products, Inc.; P.O. Box 1071; Springeld, MO 65801-1071.
PRODUCT REGISTRATION FORM
Model Number: ...................................................................................... Serial Number: .............................................................................................
Place Purchased: ..............................................................................................................................................................................................................................
Date of Purchase: .................................................................................. Purchase Price: ............................................................................................
First Name: ............................................................................................ Last Name: ...................................................................................................
City: .................................................................. State: ................................................................ Zip Code: .................................................
Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No
Stamina Products, Inc.
P.O. Box 1071
Springeld, MO 65801-1071
*If yes, be sure your email address is included above.
Detach and Mail or Fax the Form Above
TO ORDER PARTS
TO ORDER PARTS
If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions,
please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to
417-889-8064. The part will be mailed to your address.
Date of Purchase: ..................................................................................
Model #: ............................................................................................................................................................................................................................................