Stamina Products 20-1200 User Manual

Owner's
Manual

W A RNING

Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

CAUTION:
Weight on this product should not exceed 250 lbs.

This Product is Produced Exclusively by

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

2008, 03

www.stamin aproducts.com

When calling for parts or
service, please specify the
following number.

20-1200

Patent(s) pending

MADE IN CHINA

Product May Vary Slightly

From Pictured.

2008 Stamina Products, Inc.

TABLE OF CONTENTS

Page Page

Safety Instructions 2
Before Y ou Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly In struction s 7
Maintenance 10

Operational Instructions 10
Storage 14
Warranty 15
Product Parts Drawing 16
Parts List 17
Fax/Mail Ordering Form 19

SAFETY INSTRUCTIONS

WARNING:

Read all warnings posted on the Studio Tower

1.
Read this Owner's Manual before using the Studio Tower

2.
We recommend that two people be available for assembly of this product.

3.
Make sure that the Studio Tower

4.

5.

Set up and operate the Studio T ower on a solid level surface. Do not position the Studio T ower
on loose rugs or uneven surfaces.

6.

Make sure that adequate space is available for access to and around the Studio Tower .

7.

Inspect the Wooden Barre(13) for cracks before each use. Do not use the Studio Tower
Wooden Barre(13) is damaged.

8.

Make sure that the Main Frame(1) is secured properly on the Base Frame(3) with the Locking
Knobs(19) before using the Studio Tower

9.

Always make sure that the Sliders(8,10) are adjusted to the same height with Spring Pins(12) in
parallel holes in Uprights(7,9).

10.

Inspect the Studio Tower

11.

Tighten/replace any loose or worn components prior to using the Studio T ower .

12.

Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.

13.

Follow your physicia n's recommendations in developing your own personal fitness program.

14.

Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sense when exercising.

15.

Do not wear loose or dangling clothing while using the Studio Tower

16.

Be careful to maintain your balance while using, mounting, dismounting, or assembling the Studio

Tower

17.

The Studio T ower

18.

The Studio T ower should be used by only one person at a time.

To reduce the risk of serious injury, read the following Safety Instructions before
using the Studio Tower

for worn or loose components prior to use.

, loss of balance may result in a fall and serious bodily injury.

should not be used by persons weighing over 250 pounds.

.

.

.

is properly assembled and tightened before use.

.

.

if the

WARNING:

Before starting a ny exercise or conditioning progra m you should consult with your person al
physicia n to see if you require a complete physical exam. This is especially important if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJUR Y.

2

CALL US FIRST

THANK YOU FOR PURCHASING THE

Studio Tower

To help you get started, we have pre-assembled most of your

Studio Tower at the factory with the exception

of those few parts left unassembled for shipping purpose s.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into shape

and on your way to achieving a happier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M. Central Time.

Friday, 8:00 A.M. - 3:00 P.M. Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

3

STAMINA PRODUCTS, INC.

MAIL

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

BEFORE YOU BEGIN

Thank you for choosing the Studio Tower . We
take great pride in producing this quality product a nd
hope it will provide many hours of quality exercise to
make you feel better, look better and enjoy life to its
fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The Studio Tower
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier life style.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this ma nual carefully before using the Studio

Tower

.

Top Beam

Securing Strap
Securing Knob

Right Slider

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Studio T ower

, plea se
do not return the product. Contact us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T ime) on Friday.
If you would like to contact us online, go to our
website at www.sta min aproducts.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you conta ct us.

Push-Thru Spring

Eyebolt
Wooden Barre

Spring Pin

Left Upright

Arm Springs

Leg Springs

Right Upright

Locking Pin

Warning Label

Wheel Cap

Base Cushion

Outer Cover

Hand Strap

Base Frame

Main Frame

Push-Thru
Bar

Round Stand

Locking Pin

Locking Pin

Locking Knob

Main Cushion

Handle Strap

Extension Frame

Safety Strap

Roll-Down Bar

Hand Strap

Extension Cushion

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Allen Wrench (6mm)

Combination Wrench

4

4

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the Studio Tower . Please take a
moment to familiarize yourself with all of the warning & notice labels.

Label is larger than actual size

W1

WAR NING LABEL(63)

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
ends of the bolts, or screws on the circles to check for the correct di a meter . Use the small scale to check the
length of the bolts and screws.

3/16" 5/16" 1/2"3/8"1/4"

INCHES

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

45 Screw, Round He ad (M4 x 20mm) 4

47 Bolt, Button Head (M8 x 1.25 x 50mm) 2
48 Bolt, Button Head (M8 x 1.25 x 55mm) 2
49 Bolt, Button Head (M8 x 1.25 x 60mm) 4
50 Bolt, Button Head (M8 x 1.25 x 70mm) 4

55 Acorn Nut (M8 x 1.25) 4

56 Nylock Nut (M8 x 1.25) 8

59 Washer (M8) 12

61 Arc Washer (M8) 4

62 Lock Washer (M8) 4

6

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at: [e-mail]

Loop

Loop

STEP 1: Note the correct position of the holes a nd loops on the LEFT UPRIGHT(7) and RIGHT UPRIGHT(9)

in the illustration above. The holes fa ce away from the BASE CUSHION(4) a nd the loops fa ce to the outside.
Attach the LEFT UPRIGHT(7) a nd the RIGHT UPRIGHT(9) to the BASE FRAME(3) by inserting the BUTTON

HEAD BOL TS(M8x1.25x70mm)(50) and ARC WASHERS(M8)(61) from top, a nd secure with W ASHERS(M8)
(59) and NYLOCK NUTS(M8x1.25)(56) from bottom. Do not tighten the bolts until STEP 5.

STEP 2: Note the correct position of the loops on the LEFT SLIDER(8) and RIGHT SLIDER(10) in the

illustration above. The loops face to the outside.

Pull the SPRING PIN(12) then slide the RIGHT SLIDER(10) onto the RIGHT UPRIGHT(9). Release the
SPRING PIN(12) so it catches in one of the adjustment holes and locks the RIGHT SLIDER(10) in place.
Repeat with the LEFT SLIDER(8) a nd LEFT UPRIGHT(7). Position the LEFT and RIGHT SLIDERS(8,10)
so they are the sa me distance from the top of the LEFT and RIGHT UPRIGHTS(7,9).

7

ASSEMBLY INSTRUCTIONS

STEP 3

Attach the WOODEN BARRE(13) to the LEFT and RIGHT SLIDERS(8, 10) with BUTTON HEAD BOLTS
(M8x1.25x55mm)(49), LOCK WASHERS(M8)(62), and ACORN NUTS(M8x1.25)(55). Do not tighten the
bolts until STEP 5.

STEP 4

Note the correct position of the holes a nd EYEBOLTS(23) on the TOP BEAM(22) in the illustration above.
Insert the TOP BEAM(22) into the LEFT and RIGHT UPRIGHTS(7, 9) and secure with the SECURING

KNOBS(25).

STEP 5

Tighten the BUTTON HEAD BOLTS(M8x1.25x60mm)(49) to secure the WOODEN BARRE(13).
Tighten the BUTTON HEAD BOLTS(M8x1.25x70mm)(50) to secure the LEFT and RIGHT UPRIGHT(7,9).

STEP 6

Attach the OUTER COVER(15) and INNER COVER(14) to the RIGHT UPRIGHT(9) with ROUND HEAD
SCREWS(M4x20mm)(45). Repeat on other side.

8

ASSEMBLY INSTRUCTIONS

STEP 7

STEP 8

STEP 7

Refer to illustration step 7. Place the MAIN FRAME(1) with the cushion side face down. Attach the
EXTENSION FRAME(5) to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M8x1.25x55mm)(48),
WASHERS(M8)(59), and NYLOCK NUTS(M8x1.25)(56).

STEP 8

Refer to illustration step 8. Unfold the EXTENSION FRAME(5) from the MAIN FRAME(1) and turn the
cushion side face up. Attach the MAIN FRAME(1) to the BASE FRAME(3) with BUTTON HEAD BOLTS
(M8x1.25x50mm)(47), WASHERS(M8)(59), and NYLOCK NUTS(M8x1.25)(56).
Lock the MAIN FRAME(1) and the BASE FRAME(3) together with the LOCKING KNOBS(19).

9

MAINTENANCE

The safety and integrity designed into the Studio T ower can only be maintained when the Studio T ower
is regularly examined for damage and wear. Special attention should be given to the following:

1.

It is the sole responsibility of the user/owner to ensure that regular mainten ance is performed.

2.

Worn or damaged components should be replaced immediately or the Studio Tower
service until repair is made.

3.

Verify that the WARNING LABEL(63) is present and legible. Replace the WARNING LABEL(63) if it is
missing or da maged.

4.

Inspect the WOODEN BARRE(13) for cra cks or other da mage. Repla ce the WOODEN BARRE(13) if it
is da maged.

5.

Check the condition of the SAFETY STRAP(37). Replace the strap if damaged or worn.

6.

Check the condition of the SPRINGS(34, 35, 36). Replace the springs that are damaged.

7.

Check the HAND STRAPS(21) for damage. Replace damaged parts.

8.

Check the FOAM SLEEVE(29), and SPRING SLEEVE(33) and replace if damaged or worn.

9.

Check the CUSHIONS(2, 4, 6) and re place if it is damaged or worn.

10.

Only Sta mina Products supplied components shall be used to maintain/repair the Studio Tower

11.

Keep your Studio Tower

clean by wiping with an absorbent cloth after use.

removed from

.

OPERATIONAL INSTRUCTIONS

WOODEN BARRE ADJUSTMENT

To adjust the height of the WOODEN BARRE(13). Turn
the SPRING PINS(12) on the LEFT and RIGHT SLIDERS
(8, 10) counter clockwise until the knob portion can be
pulled. Pull both SPRING PINS(12) at the sa me time and
slide the SLIDERS(8, 10) up or down to adjust. Release
the SPRING PINS(12) to lock the SLIDERS(8, 10) in the
desired adjustment holes. Rotate the SPRING PINS(12)
clockwise to lock the SLIDERS(8, 10) securely .

NOTE:

Always make sure that the SLIDERS(8,10) are adjusted
so the barre is parallel with the mat.

10

OPERATIONAL INSTRUCTIONS
SET-UP FOR THE PUSH-THRU BAR

NOTE: a.

Attach the PUSH-THRU BAR(26) to one of the adjustment holes in the UPRIGHTS(7, 9) with two

1.
LOCKING PINS(30).
Attach the SECURING STRAP(32) to the EYEBOLT(23) on the top of the TOP BEAM(22). For some

2.
exercises, the PUSH-THRU BAR(26) should be up and secured in position with the SECURING STRAP
(32).
The PUSH-THRU BAR(26) can be used a s a footbar for some

3.
to the lowest adjustment holes in the UPRIGHTS(7, 9) with two LOCKING PINS(30). Lock the PUSH­THRU BAR(26) and UPRIGHTS(7, 9) together with two LOCKING PINS(30).

There are three adjustment holes in the LEFT and RIGHT UPRIGHTS(7, 9) that allow you to
attach the PUSH-THRU BAR(26) at one of three dif ferent he ights.

b.

Refer to the inset drawing. Push down the button on the "T" end of the LOCKING PIN(30) to
relea se the steel ball on the other end of the pin. Then you ca n insert the LOCKING PIN(30) into
the adjustment hole. Push the button to remove the pin.

c.

Always make sure SAFETY STRAP(37) is connected when the PUSH-THRU BAR(26) is in use.

d.

Always use SECURING STRAP(32) to keep the PUSH-THRU BAR(26) in a secure position
when not in use.

exercises. Attach the PUSH-THRU BAR(26)

Button

This bar can be used
as a footbar.

11

OPERATIONAL INSTRUCTIONS
TO USE THE ACCESSORIES:

PUSH-THRU BAR(26)

When doing exercises that require the spring resistance to come from above the bar, attach the PUSH-

THRU SPRING(34) to the loop on the upper side of the PUSH-THRU BAR(26) with the DOUBLE ENDED
CLIP(38). Atta ch the other end of the PUSH-THRU SPRING(34) to one of the loops on the T OP BEAM(22)
with the LINK(31). Refer to illustration A.

A.

When doing exercises that require the spring resistance to
come from below the bar , attach the PUSH-THRU SPRING(34)

to the loop on the underside of the PUSH-THRU BAR(26) with
the DOUBLE ENDED CLIP(38). Attach the other end of the

PUSH-THRU SPRING(34) to one of the loops on the
UPRIGHTS(7, 9) with the LINK(31). Be sure that the SAFETY
STRAP(37) is always connected to the PUSH-THRU BAR(26)

when in use. Refer to illustration B.

CAUTION !

When using the PUSH-THRU SPRING(34) from below, you
must hook the spring to the loops on the UPRIGHTS(7, 9) with

the LINK(31) and make sure the SAFETY STRAP(37) is
connected. Ensure that the SPRING SLEEVE(33) which covers

the PUSH-THRU SPRING(34) is moved over the lower part of
the spring to avoid pulling the user's hair or clothing.

12

B.

OPERATIONAL INSTRUCTIONS
TO USE THE ACCESSORIES: (continued)

SAFETY STRAP(37)

Refer to the illustration. The SAFETY STRAP(37) must be used
as follows:
When using the PUSH-THRU BAR(26) with the PUSH-THRU
SPRING(34) attached from below for bottom load exercises,
attach the SAFETY STRAP(37) to another side of the tower
from the spring. Connect one end of the strap to one of the
EYEBOLTS(23) on the TOP BEAM(22) with the LINK(31).
Connect the other end of the strap to the loop on the PUSH-

THRU BAR(26) with the LINK(31).
NOTE:

There are three D rings on each end of the SAFETY
STRAP(37). Connect the SAFETY STRAP(37) with different D
rings to set the PUSH-THRU BAR(26) in different position.

Loop

ROLL-DOWN BAR(39)

The ROLL-DOWN BAR(39) attaches via the ARM SPRINGS
(35) to the EYEBOLTS(23) on the TOP BEAM(22) between
the two UPRIGHTS(7,9) with the LINKS(31). Atta ch the ARM
SPRINGS(35) to the ROLL-DOW N BAR(39) with the DOUBLE
ENDED CLIPS(38). Be sure the links and cli ps are completely

closed and secure.

ARM SPRINGS(35)

Attach ARM SPRINGS(35) to eyebolts at desired height with the LINKS(31). Attach the other ends of the

springs to the HAND STRAPS(21) with the DOUBLE ENDED CLIPS(38). Ensure the links and clips are

completely closed and secured.

LEG SPRINGS(36)

Attach LEG SPRINGS(36) to eyebolts at desired height with the LINKS(31). Attach the other ends of the

springs to the HAND STRAPS(21) with the DOUBLE ENDED CLIPS(38). Ensure the links and clips are

completely closed and secured.

13

STORAGE

1.

Store the Studio Tower

in a clea n, dry place.

WARNING:

2.

Follow these steps and refer to the illustration to fold the Studio Tower
a.

Move any attached accessories to the back side of the tower so the mats can fold up against the

WOODEN BARRE(13).

b.

Remove the LOCKING KNOBS(19) to unlock the MAIN FRAME(1).

c.

With one hand on one of the HANDLE STRAPS(20) on the MAIN CUSHION(2), and one ha nd on the

EXTENSION FRAME(5), slowly lift the MAIN FRAME(1) and EXTENSION FRAME(5). The
EXTENSION FRAME(5) will fold down against the MAIN FRAME(1) as you lift.

d.

When both frames are in the most vertical position possible, parallel to the LEFT and RIGHT

UPRIGHTS(7,9), secure the MAIN FRAME(1) to the LEFT and RIGHT UPRIGHTS(7,9) with the
LOCKING KNOBS(19).

3.

To move the Studio Tower
folded Studio Tower

CUSHION(4), and hold the LEFT or RIGHT UPRIGHT(7,9) with your other hand. Pull the top of the
Studio T ower
with the floor. Then roll the Studio Tower
UPRIGHT(7,9) to steady and guide the Studio Tower

When folding or unfolding the Studio T ower
and ma ke sure your hands are clear of any folding or pinch point.

, it must be folded. While standing on the BASE CUSHION(4) side of the

, grasp the TOP BEAM(22) with one hand, place your foot against the BASE

toward you while holding the ba se steady with your f oot until the wheels come in contact

while holding the TOP BEAM(22) and LEFT or RIGHT

, keep all children away from the Studio T ower

for easy storage.

UNFOLD THE Studio Tower

Remove the LOCKING KNOBS(19) from the UPRIGHTS(7, 9).

a.

With one hand on one of the HANDLE STRAPS(20) on the MAIN CUSHION(2), and one hand on the

b.

EXTENSION FRAME(5), slowly unfold and lower the MAIN FRAME(1) and EXTENSION FRAME(5).
Lock the MAIN FRAME(1) to the BASE FRAME(3) with the LOCKING KNOBS(19).

c.

14

LIMITED WARRANTY

MODEL 20-1200

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation f or a period of 90 days on parts and upholstery a nd 5 ye ars
on the fra me from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL

NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO ABUSE, MISUSE, ALTERA TION OF
ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR, REPLACEMENT,
SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA PRODUCTS,
INC.

T o i mplement this li mited warranty, send a written notice stating your na me, date, and pla ce of purchase and
a brief description of the defect along with your rece ipt to Sta mina Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 [phone]. If the defect is covered under this limited
warranty , you will be reque sted to return the product or part to us for free repair or repla cement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AV AILABLE T O YOU. In the event that the purchaser makes any claim under this

limited warra nty or any implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date a nd place of purchase.

Sta mina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL OR INCIDENTAL
DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED WARRANTY.

This limited warra nty is the only written or express warranty given by Stamina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY .

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers a nd limitations of a nd on implied warrantie s and
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal re striction.

15

PRODUCT PARTS DRAWING

BACK

16

FRONT

PARTS LIST

DIAGRAM# PART NAME QTY

1 Main Frame 1
2 Main Cushion 1
3 Base Frame 1
4 Base Cushion 1
5 Extension Frame 1
6 Extension Cushion 1
7 Left Upright 1
8 Left Slider 1
9 Right Upright 1
10 Right Slider 1
11 Slider Bushing 4
12 Spring Pin 2
13 Wooden Barre 1
14 Inner Cover 2
15 Outer Cover 2
16 Wheel Cap 2
17 Base Stand 2
18 Round Stand 11
19 Locking Knob 2
20 Handle Strap 2
21 Hand Strap 4
22 Top Beam 1
23 Eyebolt 7
24 Plastic Spacer 7
25 Securing Knob 2
26 Push-Thru Bar 1
27 Push-Thru Bar Bushing 8
28 Crossing Bar 1
29 Foa m Sleeve 1
30 Locking Pin 4
31 Link 8
32 Securing Strap 1
33 Spring Sleeve 1
34 Push-Thru Spring 1
35 Arm Spring 2
36 Leg Spring 2
37 Safety Strap 1
38 Double Ended Clip 5
39 Roll-down Bar 1
40 Short Eyehook 2
41 Endcap (31.8mm) 2
42 Endcap (50mm) 2
43 Round Plug (60mm) 2

44 Recta ngular Plug (20mm x 40mm) 6

45 Screw , Round He ad (M4 x 20mm) 19
46 Screw , Flat Head (M5 x 0.8 x 8mm) 4
47 Bolt, Button Head (M8 x 1.25 x 50mm) 2

17

PARTS LIST

DIAGRAM# PART NAME QTY

48 Bolt, Button Head (M8 x 1.25 x 55mm) 2
49 Bolt, Button Head (M8 x 1.25 x 60mm) 4
50 Bolt, Button Head (M8 x 1.25 x 70mm) 4
51 Bolt, Hex Head (M6 x 1 x 20mm) 11
52 Bolt, Hex Head (M6 x 1 x 55mm) 4
53 Bolt, Flat Head (M6 x 1 x 15mm) 4
54 Acorn Nut (M6 x 1) 9
55 Acorn Nut (M8 x 1.25) 4
56 Nylock Nut (M8 x 1.25) 8
57 Washer (M4) 4
58 Washer (M6) 15
59 Washer (M8) 12
60 Arc Washer (M6) 7
61 Arc Washer (M8) 4
62 Lock Washer (M8) 4
63 Warning Label 1
64 Allen Wrench (6mm) 1
65 Combination Wrench 1
66 Manual 1
67 Video Disc (DVD) 1

18

FAX/MAIL ORDERING FORM

Plea se do not return the product. For your convenience, Sta mina has a Customer Service De partment with
a toll-free number. Should a part be missing or a defective part found, please call 1 [phone]
(in the U.S.) from 7:30 A.M. to 5:00 P.M. Central Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M.
on Friday or fill out the fax sheet ordering form below and fax it to [phone]. Our Customer Service
Department will be able to assist you with your problem and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

IMPORTANT : We must have your phone number in order to process the order!

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

IMPORTANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

MAIL

P.O. Box 1071

EXAMPLE:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1