Automatic Clothes Washer and Ventless Dryer
Instructions for use
Contents
General information, 1-2-3-4-5
Technical Information, 2-3
For your safety, 4
Introduction, 5
Installation requirements, 6-7
Attention / Grounding instructions, 6
Electrical, location and draining, 7
Installing the washer-dryer, 8-9-10-11
Unpacking the washer-dryer, 8
Removing the transit screws, 8
Connecting the water inlets, 9
Connecting the drain hose, 9
Installing the exhaust ducting, 10
Leveling the washer-dryer, 10
Completing the installation, 11
About your appliance, 12-13-14-15
Washer-dryer special features, 12
Control panel, 13
Option buttons, 14
Program key, 14
Detergent and laundry aids, 15
Dispenser drawer, 15
Washing and drying, 16-17-18-19
Cycle Description Chart, 16 Before starting a cycle, 17 Determining load sizes, 17
Setting a ‘wash’, ‘dry’ or ‘wash-to-dry’ cycle, 17 Splendide laundry tips, 18
For best results, 18
Combo laundry FAQ’s / Sample loads, 19
Care and maintenance, 20-21
Turning off the water or electricity supply, 20
Cleaning the dispenser drawer, 20
Checking the water inlet hoses, 20
Cleaning the interior, 20
Cleaning the pump pre-chamber, 21
No lint filter to clean, 21
Troubleshooting, 22-23
Read All Instructions Before Using
Troubleshooting Chart, 22 If you need assistance, 23
General Information
As an Energy Star Partner, Splendide Division of Westland Sales has determined that Energy Star labeled models meet the Energy Star guidelines for energy efficiency.
This appliance was tested by UL and conforms with both Canadian and U.S. UL safety requirements and displays their mark.
2 General Information
Technical information
Model WDC7100XC |
Splendide 7100XC |
||
Weight |
148 lbs. |
|
|
|
Width: |
23.4” (59.5 cm) |
|
Dimensions |
Height: |
33.25”-33.75” (84.5-85.7 cm) |
|
|
Depth: |
22” (55.9 cm) |
|
Minimum Installation |
Sides: 0” |
||
Clearances |
Front / Back: 1” |
||
|
|
||
Capacity |
Washing: 2 to 15 lbs. (1 to 7 kg) |
||
Drying: |
2 to 11 lbs. (1 to 5 kg) |
||
|
|||
|
|
||
Electrical Connection |
Voltage: 120 Volts, 10.5 Amp, 60 Hz |
||
Max. Absorbed Power: 1300 Watts |
|||
|
|||
|
|
||
Water Connection |
Max. Pressure: .69 MPa (6.9 bar), 100 PSI |
||
Min. Pressure: 0.05 MPa (0.5 bar), 7.5 PSI |
|||
|
|||
|
|
||
Max. Spin Speed |
Up to 1200 RPM |
||
Min. Installation Spacing
This appliance may be installed in a recessed area, closet or alcove. The installation spacing is in inches and is the minimum acceptable. *Additional spacing should be considered for easy installation, servicing and compliance with local codes and ordinances. Installations must conform with the minimum dimensions indicated.
NOTE: The manufacturer reserves the right to make any improvements to its appliances without giving prior notice.
General Information 3
For Your Safety
Save These Instructions
Your washer-dryer has been built in compliance with the strictest international safety regulations. However, for your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Read all instructions before using any appliance.
•Do not wash or dry articles that have been previously cleaned in, washed in, or spotted in gasoline, dry cleaning solvents, other flammable/explosive substances as they emit vapors that could ignite or explode.
•Before the appliance is removed from service or discarded, remove the door to the washing/drying compartment.
•Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to perform.
•Do not allow children to play on or in the appliance.
•Do not add gasoline, dry cleaning solvents, items contaminated with cooking oil or other flammable or explosive substances to the wash water. Do not install or store this appliance where it will be exposed to weather or in an area where gasoline or other flammables are stored.
•Under certain conditions, Hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the appliance, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen.
•Do not use heat to dry articles containing foam rubber or similar textured rubber-like materials.
•Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture occurs.
•Do not reach into the appliance if the drum is moving.
•Do not tamper with controls.
•Repair or replacement of a part should be made only by a qualified service technician to prevent personal injury or damage to the machine. Contact Splendide to locate an authorized repair service company near you.
•Disconnect power to the washer at the circuit breaker or fuse box, or unplug the machine in an emergency or when servicing is required. Have the installer show you and label the proper switch or fuse at the electrical disconnect box.
•Good, safe practices and caution MUST be applied when installing, operating, and maintaining any appliance. Follow basic precaution.
•Before loading the washer, make sure the drum is empty.
4 General information
Congratulations
Introduction
Congratulations on your purchase of a Splendide. Your Spendide washer-dryer takes the drudgery out of doing laundry - simply toss dirty laundry in and get clean, dry laundry out!
Whether it’s installed in a luxury RV, yacht, or apartment closet, your new Splendide is designed to fit where others won’t and deliver outstanding washing and drying performance (all while conserving more energy and water than other brands). Enjoy your new Splendide!
Read this manual
Please read this manual carefully. If you need further assistance, please contact Splendide
Laundry Centers (Mon-Fri 7am-5pm PST)
1-800-356-0766
For your records
Write model and serial numbers here. You can find them on the front of the machine and inside of the door opening.
Model:
WDC700XC
Serial No:
S/N
General information 5
Installation Requirements
ATTENTION!
For your own protection and to prevent accidents, injury, and fire, please read the following carefully before installing the washer-dryer.
•Installation and grounding must be done in accordance with local codes and by a qualified installer. Installation Instructions provided in this booklet are for the installers’ reference.
•Washer-dryer MUST be installed on a strong, level floor and in a protected dry and wellventilated area close to a power supply and drain outlet of sufficient capacity. DO NOT install on carpet.
IMPORTANT: Installation on carpet floors will cause the machine to vibrate and may result in excessive machine vibration during the spin cycles and loss of performance.
•The washer-dryer should be plugged into a properly grounded (3) prong electrical outlet capable of 120 Volt, 60 Hz, 1300 W, and 10.5 Amp. It shouldn’t be controlled by a wall switch or pull cord which could be turned off accidentally. For your safety, the third or round grounding prong must never be removed. DO NOT USE AN EXTENSION CORD.
•DO NOT install or store this appliance where it will be exposed to weather or in an area where gasoline or other flammables are stored.
! WARNING
ELECTRICAL SHOCK HAZARD
Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or electrical shock.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction, or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DO NOT modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
WARNING! Improper connection of the equipment -grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.
6 Installation requirements
Electrical
•Machine Voltage/Amperage - 120V, 60 Hz, 1300 W, 10.5 Amp.
•Connection - 3-prong plug with 6’ cord is provided with the machine.
•Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC, on a separate 15 Amp circuit.
If you have...
no access to Hot/Cold water hookups
concerns about the appliance shifting in your RV or boat
water damage concerns
You’ll need...
Splendide Faucet Adapter Kit, or equivalent.
Splendide SecureFit bracket kit, or equivalent.
Splendide Drain-A-Way Pan, or equivalent.
Location
•This machine may be installed free standing as well as in a recessed area, closet, or alcove
•Minimum Installation Spacing - 0” on sides and 1” in front and back. NOTE: Additional installation spacing needs to be considered for easy installation, servicing, and compliance with state and federal codes.
•Floor - Must support at least 280 lbs. and be a solid, level surface. DO NOT install on carpet.
•RV/Marine Installations - When locating the appliance in a towable trailer or watercraft, position the machine over the axles or mid-ship where movement is at a minimum. Block the machine to prevent extreme movement.
•NO DRYER VENT - This appliance uses an internal water condenser to dry laundry. All humidity stays within the unit and is drained as water. NO heated or conditioned air is exhausted outside; NO exhaust vent is needed.
Drainage
Standpipe Diameter/Capacity - Needs a 1 ¼” minimum diameter standpipe with a minimum carry-away capacity of 7 gallons per minute.
Top of Standpipe - Must be between 25” and 34” high from the bottom of the machine.
Outlet End of Drain Hose (provided with the unit) - Must be at least 20” above the bottom of the washer-dryer. An air break must be available at the standpipe to avoid siphoning. No more than 6” of the drain hose should be inserted into the drain pipe to prevent siphoning.
Installation requirements 7
Installing the washer-dryer
Unpacking the washer-dryer
•Carefully remove the packing materials with care not to damage the drain hose and power cord that are shipped installed on the machine. Check that the machine is intact. Report any damage immediately.
•Position the washer-dryer near the desired installation position.
IMPORTANT: Retain the transit screws, spacers and rubber tubes. These items should be reinstalled to prevent damage if or when you transport the machine in the future.
WARNING! Plastic bags, styrofoam, nails and other packaging parts are not children’s toys and can be potentially dangerous. Destroy the carton and plastic bags after the washer-dryer has been unpacked.
Removing the transit screws
For transportation, the inside of the machine is supported by screws, rubber grommets and spacers on the back panel. Before using the washer-dryer, these items MUST be removed.
IMPORTANT: Transit screws and spacers must be removed before operating the machine to allow proper operation of the machine and to prevent damage to the appliance.
•After positioning
the washer-dryer near the installation location, remove the four screws (Fig.1), with the rubber grommets and plastic spacers that are attached to them.
•Use the plastic plugs (provided in the accessories bag) to fill in the holes.
Connecting the water inlets
If the water pipes you will be connecting to are new or unused, run the water until clear to remove any debris that could clog the water valve screens or valves before connecting the machine. NOTE: Supply shut-off valves should be easily accessible.
IMPORTANT: Water pressure MUST range within the values indicated on the “Technical Data” chart
•Included in the accessories supplied with your machine are 2 inlet hoses with 4 rubber washers pre installed. Check that the rubber washers are installed in the ends of the inlet hoses to make a water tight seal at each connection point.
•Connect the straight ends of the water inlet hoses to the supply taps that have ¾” BSP thread (standard hose bib).
•Connect the 90º angled ends (20 mm thread) of these hoses to
the inlet valves
on the back of |
|
|
|
the machine (Fig. |
|
|
|
2). NOTE: Water |
H |
C |
|
Inlet valves are |
|||
|
|||
color coded: |
|
|
|
Red (Hot) & |
|
|
|
White (Cold). |
|
Fig 2 |
|
|
|
IMPORTANT: Do not use excessive force. Damage to the couplings can result. The couplings should be tightened by hand; a tool should only be used if a leak occurs.
8 Installing the washer-dryer
Loading...