Splendide 6200 User Manual

0 (0)

Splendide

Washer-Dryer

Installation Instructions and Use & Care Guide

Lave-linge séchant

Mode d’installation et d’emploi

Lavasecadora

Instrucciones para la instalación y el uso

Quick Reference Guide

WDC6200CEE

Comb-o-matic 6200 Energymizer

™

Technical Data . . . . . . . . . . . . . . . . . . . . . .

Installation Instructions

Installation Requirements . . . . . . . . . . . . . . . . . Installation/Removal . . . . . . . . . . . . . . . . . . . .

Introduction . . . . . . . . . . . . . . . . . . . . . . . .

Getting Started

About Your Washer-Dryer . . . . . . . . . . . . . . . . . Understanding the Control Panel . . . . . . . . . . . . . . Guide to the Wash Programs . . . . . . . . . . . . . . . . Preparing Laundry / About Laundry Aids . . . . . . . . . . . . Fabric Care Labels / Stain Removal Chart . . . . . . . . . . .

Operation Instructions

Choosing a Load . . . . . . . . . . . . . . . . . . . . . About the Dispenser Drawer . . . . . . . . . . . . . . . . How to Wash . . . . . . . . . . . . . . . . . . . . . . . How to Dry . . . . . . . . . . . . . . . . . . . . . . . .

Easy Care and Maintenance

Regular Maintenance. . . . . . . . . . . . . . . . . . . . Monthly/Yearly Maintenance . . . . . . . . . . . . . . . . .

Troubleshooting

Avoid Service Checklist . . . . . . . . . . . . . . . . . . If You Need Service. . . . . . . . . . . . . . . . . . . . .

3 4

7 8 9 10 11

12 13 14 15

16 17

18 19

Read All Instructions Before Using

DO NOT DISCARD!

HIS INFORMATION

SUPERSEDES THE

INFORMATION FOUND IN

YOUR OWNERS MANUAL

KEEP THIS PAGE WITH YOUR

OWNERS MANUAL FOR

FUTURE REFERENCE

DOOR LOCK SUPPLEMENT

Follow these steps if you need to open the door to your washer-dryer after a cycle has already begun

To Open the Door During a Wash Cycle:

1. Advance the Program Selector to ‘Reset’ and wait 5

seconds.

2. Advance the Program Selector to ‘Drain’ (8 o’clock) and allow the machine to drain completely.

3. Advance the Program Selector to ‘Reset’ (The ‘Status/ Door Lock’ LED will blink quickly to indicate that the cycle has stopped, but the door is STILL LOCKED)

4. When the ‘Status/Door Lock’ LED blinks SLOWLY (takes

1-2 minutes), you can open the door

! !

IMPORT

Once a wash or dry cycle is underway, the washer-dryer door will LOCK for the duration of the cycle and will STAY LOCKED for up to 2 minutes after the cycle ends. DO NOT attempt to open the door unless

the ‘STATUS/DOOR LOCK’ LED is BLINKING SLOWLY!

To Open the Door During a Dry Cycle:

1. Advance the Program Selector to ‘Reset’ (The ‘Status/

Door Lock’ LED will blink quickly to indicate the cycle has stopped, but the door is STILL LOCKED)

2. When the ‘Status/Door Lock’ LED blinks SLOWLY (takes 1-2 minutes), you can open the door

Splendide®

WASHERDRYER

Front-Loading Washer-Dryer

Addendum to Owners Manual

MODELS

WD2000S (Splendide 2000S) WD2100 (Splendide 2100) WDC6200 CEE (Comb-o-matic 6200) WDC5200 (Comb-o-matic 5200)

QUESTIONS?

Splendide Service HQ:

Westland Sales 15650 SE 102nd Ave. (PO BOX 427) Clackamas, OR 97015

Telephone: Toll Free: 800-356-0766 (Local: 503-655-2563)

Service Fax: (503) 722-9202 E-mail: service@splendide.com Website: www.splendide.com

WINTERIZATION SUPPLEMENT

Follow theses steps if you need to winterized your washer-dryer that’s installed in a boat or RV

To winterize your washer-dryer:

1. With the machine power OFF, pour ½ quart of RV-

type antifreeze into the washer drum

2. Close the door. Advance the Program Selector knob to a SPIN position

3. Press ON/OFF Button (IN). Wait 1-2 minutes

4. Press ON/OFF Button (OUT). Unplug the washer-dryer

from the electrical outlet (or disconnect power)

5. Turn the water supply faucets OFF. Disconnect the inlet hoses from the faucets. Drain any remaining water from the hoses. Finished!

Optional RV Winterization - If you’re currently

pumping antifreeze through the fresh water

system, follow these steps to winterize:

1. With the machine power OFF, turn the WASH TEMP

knob to HOT

2. Advance the Program Selector knob to REGULAR in

Cotton Heavy Duty

3. Press the ON/OFF button (IN) and let the machine

ﬁ ll until antifreeze is in the drum

4. Advance Program Selector to a RESET. Wait 5

seconds (Status/Door Lock LED will blink)

5. Advance Program Selector to a SPIN position. Let

the antifreeze drain from the drum

6. Advance Program Selector to RESET. Wait 5 seconds

(Status/Door Lock LED will blink)

7. Turn the WASH TEMP knob to COLD

8. Advance the Program Selector knob to REGULAR in

Cotton Heavy Duty

9. Let the machine ﬁ ll until you see antifreeze in the drum

10. Advance the Program Selector knob to RESET. Wait 5 seconds (Status/Door Lock LED will blink)

11. Advance the Program Selector knob to SPIN. Let the antifreeze drain from the drum

12. Press the ON/OFF button (OUT). Finished!

To use again, ﬂ ush the water pipes, then:

1. Reconnect the water inlet hoses to the correspond-

ing HOT/COLD faucets. Turn the faucets ON. (NOTE: Check the water inlet hoses and pump periodically. Refer to the “Use & Care Guide” that came with the machine)

2. Plug the washer-dryer into an appropriate electrical outlet (or reconnect power supply)

3. With the ON/OFF button in the oﬀ (OUT) position, pour 1/2 TBSP. of powder detergent (or liquid equiv.) into the ‘Detergent’ compartment inside the Dispenser Drawer

4. Advance the Program Selector knob to an EXPRESS cycle

5. Press the ON/OFF button (IN) and allow the machine to run through the complete cycle to clean out any remaining antifreeze. Finished!

Technical Data

Models

Dimensions

Capacity

Electrical Conn.

Water Conn.

Spin Speed

NOTE: The manufacturer reserves the right to make any improvements to its appliances without giving prior notice.

Comb-o-matic 6200 by Splendide (WDC6200CEE)

Width: 23.4" (59.5 cm) Height: 33.25"-33.75" (84.5-85.7 cm)

Depth: 22.9" (58.1 cm)

Drum Size: 1.92 CF Washing: 2-12 lbs. Drying: 2- 8 lbs.

Voltage: 120 Volts, 13 Amp, 60 Hz Max. Absorbed Power: 1300 Watts

Max. Pressure: .69 MPa (6.9 bar), 100 PSI Min. Pressure: 0.05 MPa (0.5 bar), 7.5 PSI

Up to 1200 RPM

nMinimum Installation Spacing

This appliance may be installed in a recessed area, closet or alcove. The installation spacing is in inches and is the minimum acceptable. Additional

spacing should be considered for easy installation, servicing and compliance with local codes and ordinances. Installations must conform with the minimum dimensions indicated.

Recessed Front View

0" *

* Additional clearances for wall, door/floor moldings may be required.

As an Energy Star Partner, Splendide Division Westland Sales has determined that Energy Star labeled models meet the Energy Star guidelines for energy efficiency.

0" *

US LISTED

Side View

1" **

This appliance was tested by UL and conforms with both Canadian and U.S. UL safety requirements and displays their mark.

Installation Instructions

Installation Requirements

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction, or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DO NOT modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING: Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.

Attention!

For your own protection and to prevent accidents, injury, and fire, please read the following carefully before installing the washerdryer.

nElectrical

• Machine Voltage/Amperage - 120V, 60 Hz, 1300 W, 13 Amp.

• Connection - 3-prong plug with 6' cord is provided with the machine.

• Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC, on a

separate 15 Amp circuit.

nLocation

This machine may be installed free standing as well as in a recessed

area, closet, or alcove.

• Minimum Installation Spacing - 0" on sides and 1" in front and back.

NOTE: Additional installation spacing needs to be considered for easy installation, servicing, and compliance with state and federal codes.

• Floor - Must support at least 280 lbs. and be a solid, level surface. DO

NOT install on carpet.

• RV/Marine Applications - When locating the appliance in a towable

trailer or watercraft, position the machine over the axles or mid-ship where movement is at a minimum. Block the machine to prevent extreme movement.

• No Dryer Vent Requirements For This Machine - This machine uses

an internal condenser for drying. All humidity stays within the unit and is drained as water. No heated or conditioned air is exhausted outside; no exhaust vent is needed.

• Installation and grounding must be done in accordance with local

codes and by a qualified installer. Installation Instructions provided in this booklet are for the installers’ reference.

• Washer-dryer MUST be installed on a strong, level floor and in a

protected dry and well-ventilated area close to a power supply and drain outlet of sufficient capacity. DO NOT install on carpet.

IMPORTANT: Installation on carpet floors will cause the machine to vibrate and may result in excessive machine

vibration during the spin cycles and loss of performance.

• The washer-dryer should be plugged into a properly grounded (3)

prong electrical outlet capable of 120 Volt, 60 Hz, 1300 W, and 13 Amp. It shouldn’t be controlled by a wall switch or pull cord which could be turned off accidentally. For your safety, the third or round grounding prong must never be removed. DO NOT USE AN EXTENSION CORD.

• DO NOT install or store this appliance where it will be exposed to

weather or in an area where gasoline or other flammables are stored.

WARNING: Splendide denies all liability if these instructions are not followed correctly.

nDrainage

• Standpipe Diameter/Capacity - Needs a 1 ¼” minimum diameter

standpipe with a minimum carry-away capacity of 7 gallons per minute.

• Top of Standpipe - Must be between 25" - 34" high from the bottom of

the machine.

• Outlet End of Drain Hose (provided with the unit) - Must be at

least 20" above the bottom of the washer-dryer. An air break must be available at the standpipe to avoid siphoning. No more than 6" of the drain hose should be inserted into the drain pipe to prevent siphoning.

nSplendide Accessories (Available Separately)

• Faucet Adapter Kit allows for a direct faucet connection.

• Optional Drain-A-Way Pans designed to be drain plumbed.

Installation Instructions

Installation / Removal

n1. Unpacking Your Washer-Dryer

• Carefully remove the packing materials with care not to damage the drain

hose and power cord that are shipped installed on the machine. Check that the machine is intact. Report any damage immediately.

• Position the washer-dryer near the desired installation position.

WARNING: Plastic bags, Styrofoam, nails and other packaging parts are not children’s toys and can be potentially dangerous.

Destroy the carton and plastic bags after the washer-dryer has been unpacked.

n2. Remove the Transit Screws/Spacers

• For transportation, the inside of the machine is supported by screws,

rubber grommets and spacers on the back panel. Before using the washer-dryer, these items MUST be removed.

IMPORTANT: Transit screws and spacers must be removed before operating the machine to allow proper operation of the

machine and to prevent damage to the appliance.

• After positioning the washer-dryer

near the installation location, remove the four screws (Fig.1), with the rubber grommets and plastic spacers that are attached to them.

• Use the plastic plugs (provided in

the accessories bag) to fill in the holes.

Fig. 1

IMPORTANT: Retain the transit screws, spacers and rubber tubes. These items should be reinstalled to prevent damage if

or when you transport the machine in the future.

• Included in the accessories supplied with your machine are 2 inlet hoses

with 4 rubber washers preinstalled. Check that the rubber washers are installed in the ends of the inlet hoses to make a water tight seal at each connection point.

• Connect the straight ends of the

water inlet hoses to the supply taps that have ¾” BSP thread (standard hose bib).

• Connect the 90º angled ends (20

mm thread) of these hoses to the inlet valves on the back of the machine (Fig. 2). NOTE: Water

Inlet valves are color coded: Red (Hot) & White (Cold).

IMPORTANT: Do not use excessive force. Damage to the couplings can result. The couplings should be tightened by

hand; a tool should only be used if a leak occurs.

Optional Single Faucet Hook-Up

It is possible to run the machine on cold water only, but a water supply must be connected to each inlet valve. To do this, we suggest you use a “Y” connector (contact Splendide). Connect the “Y” connector to a tap. After checking that the 4 rubber washers (provided) are installed in the

Fig. 3

90º angled ends of these hoses to the inlet valves on the back of the machine (Fig. 2). NOTE: When the machine is connected to a single

faucet, the water temp. for the wash/rinse settings is regulated by the temperature YOU set at the faucet. If hot or warm water is used for washing, it is important to turn the faucet to COLD after the wash cycle. Cold water is essential to your machines

ends of the inlet hoses, connect the straight ends of the hoses to the “Y” connector (Fig. 3). Then connect the

’

condensation drying process.

Fig. 2

n4. Water Drainage

• It is possible for the water to be discharged into a sink, standpipe or

n3. Connecting Water Inlet

• If the water pipes you will be connecting to are new or unused, run the

water until clear to remove any debris that could clog the water valve screens or valves before connecting the machine. NOTE: Supply

shut-off valves should be easily accessible.

IMPORTANT: Water pressure MUST range within the values indicated on the “Technical Data” chart (p. 1).

WARNING: Splendide denies all liability if these instructions are not followed correctly.

drainpipe, but an air break must be available at a min. 20" height to prevent the machine from siphoning (Fig. 6).

Standpipe Drain System - Installations require a minimum 1 ¼” (3.2 cm)

diameter standpipe with a minimum carry away capacity of 7 gallons (26 liters) per minute.

Wall or Floor Standpipe Drain System - The top of the standpipe

must be between 25" (62 cm) - 34" (86 cm) from the bottom of the washer (Fig. 4).

Continued on next page

Installation Instructions

Floor Standpipe Wall Standpipe

A & B = 25" (62 cm) min. / 34" (86 cm) max.

Fig. 4

Sink Drainpipe System - Entry into the sink drain system must be above

the trap (Fig. 5). When routing the drain hose through cabinets or walls, use a protective material such as electrical or duct tape to cover sharp edges that could damage the drain hose. Use a suitable clamp to secure the drain hose to the “Y” branch or the disposer. With a sink drainpipe system, you may connect directly: 1) to a disposer by following the manufacturers attachment method. 2) directly to a “Y” branch tail piece (available at most hardware stores). 3) Through the floor to a separate trap. The trap must be vented to prevent siphoning. To provide proper venting, install an Air Gap Kit (available at most hardware stores). 4) To the to the faucet using a Faucet Adapter Kit (available separately). It will supply water from your faucet and discharge water directly into your sink drain.

Sink Drain W/ "Y" Branch Tailpiece

25" (62 cm) min. with an air break

Laundry Sink Drain

Floor Standpipe

U-Clamp

20" (50 cm) min. with an air break

Standpipe

Floor Standpipe w/ "Y" Branch Tail Piece

Cable tie

"Y" Tail Piece

This connection MUST be before drain trap and at least 20" (50.8 cm) above the floor where washer will be installed.

n5. Leveling

• To access the front leveling legs, tilt the

machine backwards, leaning it against a wall or other stable structure.

• Adjust the legs up or down (Fig. 8) to

ensure the washer is resting solid and does not rock side-to-side or front-to-back when the machine is upright.

• Check that the angle of inclination,

measured according to the worktop, does not exceed 2°.

6" max.

20" (62 cm) min. 34" (86 cm) max.

Standpipe

25" (62 cm) min. 34" (86 cm) max.

Fig. 6

Fig. 7

Fig. 8

Fig. 5

IMPORTANT: Make sure that the drain hose is not kinked and that water flow is not restricted.

• Use a U-Clamp (provided in your accessories packet) or suitable item to

secure the outlet end of the drain hose (pre-installed on the back of your machine).

• Insert the outlet end of the drain hose into the standpipe, wall or floor

drain (Fig. 6). NOTE: The outlet end of the drain hose MUST be at least 20" (50 cm) above the base of the machine. No more than 6" of the drain hose should be inserted into the drain pipe to prevent siphoning.

• Use a strap, cable tie, or similar item to hold the hose or the U-Clamp in

place.

WARNING: Splendide denies all liability if these instructions are not followed correctly.

n6. Electrical Connection

• Plug the power cord into a grounded outlet. See “Grounding

Instructions” (p. 2) for complete details. NOTE: Check to ensure the

power is OFF at a circuit breaker/fuse box before plugging the power cord into the outlet. Turn power on at the circuit breaker/fuse box.

n7. Before Using Your Washer-Dryer

• Read manual thoroughly. Keep these instructions for future reference.

• Run the empty washer-dryer through a complete wash cycle to check for

water leaks and proper operation.

• Wipe the inside and outside of the appliance with a damp cloth to remove

any dust that has accumulated during transit.

IMPORTANT: The machine must rest solid on a sturdy floor for optimum performance and minimum vibration.

Introduction

Congratulations!

Thank you for choosing Splendide - North America’s #1 selling combination laundry center since 1984. Your new Splendide washerdryer is designed to give you maximum washing and drying performance while using less energy/resources and taking up less space. The performance levels, safety features, sturdiness and all its functions are the result of ongoing technological innovation. The ultimate purpose? To offer you the best performance with the utmost simplicity.

nRead This Manual

Inside this book you will find many helpful hints on how to install, use

and maintain your new washer-dryer properly. Please read this manual carefully. Just a little preventative care on your part can save you a great deal of time and money over the life of your washer-dryer. If you need further assistance, please contact Splendide Laundry Centers at 1-800-356-0766.

nFor Your Records

Write model and serial numbers here. You can find them on the front

of the machine and inside of the door opening.

Model #:

Serial #:

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock, DO NOT remove cover (or back)/No user servicable parts inside. Refer servicing to qualified services personnel.

The lightning flash with arrowhead symbol, with-in an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Save these instructions

For Your Safety

Your washer-dryer has been built in compliance with the strictest international safety regulations. However, for your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

• Read all instructions before using any appliance.

• Do not wash or dry articles that have been previously cleaned in,

washed in, or spotted in gasoline, dry cleaning solvents, other flammable/explosive substances as they emit vapors that could ignite or explode.

• Before the appliance is removed from service or discarded, remove

the door to the washing/drying compartment.

• Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

• Do not allow children to play on or in the appliance.

• Do not add gasoline, dry cleaning solvents, items contaminated with

cooking oil or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

• Do not place flammable substances around your washer-dryer during

operation.

• Under certain conditions, Hydrogen gas may be produced in a hot

water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the appliance, turn on all hot water faucets and let the water flow from each for several min. This will release any accumulated hydrogen.

• Do not use heat to dry articles containing foam rubber or similar

textured rubber-like materials.

• Turn off water faucets to relieve pressure on hoses and valves and to

minimize leakage if a break or rupture occurs.

• Do not reach into the appliance if the drum is moving.

• Do not tamper with controls.

• Repair or replacement of a part should be made only by a qualified

service technician to prevent personal injury or damage to the machine. Contact Splendide to locate an authorized repair service company near you.

• Qualified service personnel should clean the interior of the machine

periodically.

• Disconnect power to the washer at the circuit breaker or fuse box, or

unplug the machine in an emergency or when servicing is required. Have the installer show you and label the proper switch or fuse at the electrical disconnect box.

• Good, safe practices and caution MUST be applied when installing,

operating, and maintaining any appliance. Follow basic precaution.

• Save these instructions.

• Before loading - Before loading the washer, make sure the drum is empty.

+ 14 hidden pages