SPEEDZONE SPORT CYCLOCOMPUTER
Congratulations on your purchase and welcome to the growing number of cyclists who are discovering a powerful new generation of bicycle computers. Your Specialized SpeedZone® Sport has been designed to provide the best combination of performance, features, durability, ease of use and installation.
Your SpeedZone Sport bicycle computer is equipped with the following functions:
•SPD - Current Speed
•AV – Average Speed
•MAX – Maximum Speed
• DST - Trip Distance
• OD - Odometer (total distance)
• TM – Ride Timer
• 12/24 Hour Digital Clock
• Easy Calibration Mode
1
This computer also features:
•Heavy-duty abrasion resistant pick-up wire
•Water resistant housing
•Dual Display LCD
•2 Year Warranty
What is included in your SpeedZone Sport package:
1.SpeedZone Sport computer (1)
2.Mounting bracket (1)
3.Magnet with screw (1)
4.Cable tie wraps (4)
5.Mounting bracket sizing straps (3)
1
2
3 5 
4
2
FIGURE 1: |
FIGURE 2: |
SENSOR |
MAGNET |
PLACEMENT |
ATTACHMENT |
MOUNTING
THE SPEEDZONE SPORT
The SpeedZone Sport sensor can mount on the right or left side of the fork blade. Use the cable tie-wraps provided to position the sensor. Do not tighten until the final placement of the sensor magnet is correct. (See figure 1)
FIGURE 3: MOUNTING BRACKET
Attach the magnet to a spoke across from the sensor with the magnet screw. The clearance between the magnet and the sensor should be approximately 1/32"-1/16" (1-2mm). Tighten the magnet and transmitter. Do not overtighten the magnet screw. (See figure 2)
Attach the mount to the handlebar using the bracket screw provided. Tighten so that the bracket cannot rotate on the handlebar. There are several
3
sizing straps provided to fit different diameter bars. (See figure 3) Slide the computer forward onto the mounting until it ‘snaps’ into place with an audible click. To remove the computer, push it backward until it releases from the mount. To test for proper installation of the magnet, sensor and computer, activate the computer by picking up the front of the bicycle and spinning the wheel. The "wheel" (1) indicator will flash. If it does not flash check the sensor and magnet alignment. Realign as necessary until the "wheel" indicator flashes while spinning the wheel.
PROGRAMMING
Programming the functions of your SpeedZone Sport requires it to be placed in various "modes" (i.e. odometer mode, stopwatch mode).
The computer can be cycled through these modes by pressing the "MODE" button located on the right-hand side of the housing. Once a specific mode has been entered, its values can be reset or adjusted by pressing the "FUNCTION" button located on the left-hand side of the housing.
1. Miles or Kilometers selection
Your SpeedZone Sport will record speed and distance in either miles (M) or kilometers (KM). To select miles or kilometers, push the "MODE" button until ODO (odometer) appears in the lower left side of the display (This is called the odometer mode). Hold down the "FUNCTION" (left side) button and ‘tap’ the "MODE" button once. The KM, M indicator will begin blinking. You may now alternate between miles
4
and kilometers by pressing the "MODE" button. When the correct choice is flashing, select it by pressing the "FUNCTION" button. You will now enter the "Programmable Odometer" mode. If the odometer setting is correct push the "FUNCTION" button 4 times to exit to odometer mode. (Otherwise, see "Setting the programmable odometer" below)
2.Setting the Programmable Odometer
To access the programmable odometer mode, first advance the "MODE" button until (OD) appears on the bottom of the screen. Then hold down the "FUNCTION" button and ‘tap’ the "MODE" button once. (See figure 4) The Km/h indicator will flash. If the Km/h setting is correct press the
FIGURE 4: PROGRAMMABLE
ODOMETER SCREEN
"FUNCTION" button once and a fourdigit number will appear. You are now in the programmable odometer mode. This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. To enter a mileage into the odometer, press the "MODE" button until the flashing digit is correct. (Note: The "MODE" button may be held to
5
Loading...