Southern Folger 8010L User Manual

FOR GROUPS OF
SLIDING CELL DOORS

Maximum security.

8010L PNEUMATIC
LOCKING SYSTEM

For use where remote electric
unlocking
required, but door movement can be
by hand at the door. This system also
provides emergency pneumatic
unlocking from a remote location.
Doors are locked at top and bottom in
both the open and closed positions by
means of a concealed vertical lock bar
at the rear jamb of each door. The
vertical lock bar is deadlocked at a
third locking point inside the horizontal
cover box above the door. Standard
clear door opening widths available
are 2'4" to 3'2".

of groups of sliding doors is

L O C K I N G S Y S T E M S

8010L

PNEUMATIC

LOCKING SYSTEM

FUNCTION:

ELECTRIC - Individual switches
located
actuate a pneumatic cylinder housed
in the horizontal cover box over each
door, raising the vertical lock bar and
unlocking the door. Upon unlocking,
the door springs open a few inches.
All door movement is by hand at the
door, which automatically
snap/deadlocks when moved to the
fully closed or fully open position.
Individual lamp indicators on the
control panel show locked/unlocked
condition. A single switch can provide
group unlocking.

MECHANICAL - In the absence of
pneumatic or electrical power, doors
may be individually unlocked with a
manual release tool. Door movement
is by hand and door will relock in either
fully open or closed position.

EMERGENCY GANG RELEASE
In an emergency, all doors in a cell line
may be simultaneously unlocked from
a remote location using a pneumatic
release system. While in emergency
release mode, doors will not relock in
any position.

on a remote control panel

-

TECHNICAL DATA:

• COVER BOX:
1' 0-3/4" H x 7-1/2" D

• COVER BOX MATERIAL:
7 gauge steel plate

• HINGED PANEL:
10 gauge steel

• DOOR ROLLERS:
3" diameter, machined
steel with sealed bearings.

• VERTICAL LOCK BAR
DIMENSIONS:
5/8" SQ
of door.

•

FINISH: Prime paint

•

DOOR HANGER:
7 gauge steel plate

by full height

•

ELECTRICAL: 24 VDC
Minimum five 24 volt conductors
are required between the
control point and the door,
except for those models
having the letter “K”
(keyswitch) in the suffix.
Keyswitch models require
minimum

•

AIR REQUIREMENTS:
Air consumption 1.9 cubic
inches per unlock operation at
80 PSIG.

six conductors.

Revised 3/09

FOR MORE INFORMATION, PLEASE CALL 210-533-1231

C7

FOR GROUPS OF
SLIDING CELL DOORS

Maximum

STANDARD FEATURES:

• Bottom door guide

• Door hanger

• Pneumatic emergency release

• Sloped-front cover box

• Hinged cover panel for maintenance access

• Vertical lock bar assembly

• ASTM F1643 Certified
Horizontal and Vertical Impact Test-Grade 1

• Prime paint finish

security.

L O C K I N G S Y S T E M S

8010L PNEUMATIC

LOCKING SYSTEM

8010L PNEUMATIC SLIDING DOOR SYSTEM

OPTIONAL FEATURES:

PILASTER RELEASE - (In lieu of pneumatic
release system.) Hip-high paracentric keyed
mechanical release mounted in a full-height
pilaster adjacent to the receiving jamb.
Specify “8010LP-1” keyed one side.

ELECTRIC KEYSWITCH- Paracentric or mogul
keyed local electric control switch
mounted below mechanical release mechanism in
pilaster.
Specify “8010LPK-1” for paracentric keyed
one side.

Specify “8010LPKM-1” for mogul keyed one side.

HOT DIP GALVANIZED FINISH - Available for
external applications with lift-off cover panel only.
Not available with standard hinged cover panel.
Specify [G] when ordering. Example: 8010LP-1G

NO LOCK OPEN - Specify “NLO.”
Door does not lock in open position.

FACTORY- WIRED CONTROL CABLE ­Specify “8010LWC.”

DETAIL A – SLOPED BOX

COVER BOX SECTION

7-1/ 2” de ep x 1’-0-3/ 4” ta ll cov er box
fiel d wel ded 1” on 6 ” top and b ottom

DETAIL C – RECEIVER

RECEIVER JAMB SECTIO N

Flus h rec eiver jamb a llows frame
open ing a nd cle ar ope ning to
be the sa me.

DETAIL B – VERTICAL LOCK JAMB BAR

DETAIL D – BOTTOM DOOR GUIDE SECTION

NOTE: Cover box minimum length =

overtravel) + (2 x clear opening) + 9".

(7"

*For doors exceeding 300 lbs. and/or greater
than 3’-2” clear opening, contact factory.

C8

Revised 7/12

8010L Shown

Note: Other system configurations and details are available.

Call Customer Service for more information.

P.O. BOX 2021 • SAN ANTONIO, TX • 78297 • 210-533-1231 • FAX: [phone]