Southern Folger 50HBM User Manual
FA Rev. 02-10 A9
For more information, please call 210.533.1231.
Description______________
Series 50HBM Deadlatches are lever
tumbler, motor-operated locks for
sliding doors, utilizing hookbolts. Specify
keying as follows:
51 Keyed case side
52 Keyed cover side
56 Keyed both sides
Applications_____________
Jamb-mounted 50HBM locks should be
specified for maximum security cell,
corridor, sallyport, or entrance/egress
sliding doors. May be installed within a
lock pocket or full height column. They
are designed to be part of an electrical
locking/unlocking system to provide
institutional staff with maximum safety
and flexibility of operation.
Operations______________
All 50HBM locks are operated by electric
motor. The choice of two motor
operations provides a variety of
functions:
Full-Rotation Motor (50HBM)
with latchback (1):
Unlocks when the motor is energized by
a momentary contact switch. Once
unlocked, the hookbolt is held
mechanically in the raised position until
the door is opened. It then returns to
normal, lowered position.
Two-Position Motor (50HBMC)
without latchback (2):
Same as above, except that the
hookbolt is raised and lowered as the
motor runs. A door starter should be
installed in the track housing to push
the door open when the motor reaches
the unlocking point.
Testing__________________
50HBM locks have been tested for over
1,000,000 operations.
Standard Features_______
Motor voltage – 120VAC
External mounting – Locks install
without cover plate removal. External
slotted mounting holes simplify
installation and allow for variations in
door gap by permitting lateral
movement.
Two-piece plug connector –
Simplifies wiring at time of installation
and allows pre-wiring at the lock
pocket.
Superior durability – Working parts
are stainless steel and designed for
maximum strength and corrosion
resistance.
Hardened hookbolt and deadlock
actuator – Zinc plated for corrosion
resistance.
Motor operation – A choice of two
operations is available, as shown on
following page.
High security – Choice of five or six
lever tumbler models. Six tumbler
model offers greater pick resistance.
Mechanical unlocking by key –
Once unlocked by key, the hookbolt
remains in that position until relocked
by key (Models without latchback
feature). Key is removable in the
unlocked position.
Indication switch – The indication
switch monitors the deadlock lever to
indicate a deadlocked hookbolt.
Finish – Zinc plated.
FOLGER ADAM ELECTRIC LOCKS
Key: Prison Paracentric
Door: Sliding
Security
Level: Maximum
50HBM DEADLATCH
A10 Printed in USA FA Rev. 02-10
P.O. Box 2021, San Antonio, TX 78297 Ph: 210.533.1231 Fx: 210.533.2211
Web: www.SouthernFolger.com
Email: info@southernfolger.com
Optional Features________
Motor voltage – 24VDC
Lock bolt keepers – Select 50H-4DB
with dust box.
Dimensional Data________
Note: Dimensions are for information
and planning purposes only and should
not be used as templates.
Specifications_________
Case – 7 and 10 gauge steel.
Cover – 10 gauge HRS.
Hookbolt – .5 inch steel, case
hardened and zinc plated.
Deadlock actuator – .5 inch
square CRS, hardened and
zinc plated.
Deadlock and operator levers –
Stainless steel.
Springs – Stainless steel.
Motor – Synchronous-type
gearmotor with brake.
Electrical
Characteristics________
Motor (AC) – Synchronous-type
gearmotor with brake.
Ratings: 120VAC, 60HZ, 1.3 amps
at full load.
Motor (DC) – Permanent magnet
gearmotor.
Ratings: 24VDC, 2.2 amps at full
load.
Indication switch – SPDT,
UL Listed.
Deadlock Ratings: 15 amps at 125
or 250 VAC.
Auxiliary Ratings: 10 amps 125
or 250 VAC.
FOLGER ADAM ELECTRIC LOCKS
Key: Prison Paracentric
Door: Sliding
Security
Level: Maximum
50HBM DEADLATCH
MODEL NO.
OPERATION
DESCRIPTION
LATCHBACK
OPERATION
SWITCHES
INTERLOCK
INDICATION
SWITCH
DEADLOCK
WITH WITHOUT
50HBM-1-01 1 X X
50HBMC-1-04 2 X X
LEGEND
50HB Series Locks
LOCK COVER PLATE TRACK SIDE
56HB
KEYED
BOTH
SIDES
52HB
KEYED
TRACK
SIDE
31 HRHL 23
33 HRHL 34
Specify circled swing number when ordering.
This chart shows applicability of functions and features to specific 50HBM models.
For complete details, see How To Specify on the following page.
Loading...