Sony Ericsson W760 Equipment List

Equipment List, Electrical

Applicable for W760

Contents

General................................................................................................................................................................ 2

1

2 Column Definitions............................................................................................................................................. 2

Description Columns ............................................................................................................................................ 2

Process Columns ................................................................................................................................................. 2

3 Repair Equipment............................................................................................................................................... 3

3.1 Repair Equipment orderable from Sony Ericsson...................................................................................3

3.2 Repair Equipment that should be obtained from local Suppliers............................................................ 7

3.3 Lead-free Solder Equipment................................................................................................................. 23

4 Revision History............................................................................................................................................... 25

1211-1566_4 Company Internal

Equipment List, Electrical

1 General

This document describes the equipment needed, in addition to the equipment listed in the Mechanical Equipment List, to upgrade the applicable product’s software, functional test and to repair the product at an Electrical Repair Level. The first section is equipment that can be purchased from a Sony Ericsson Parts and Tools warehouse. The second section is equipment that must be purchased from other vendors.

2 Column Definitions

Description Columns

• Description = The name of the equipment.

• Part Number = The Sony Ericsson part number to use when ordering from a Sony Ericsson Parts and Tools warehouse.

• Comments = Additional information that helps to specify or clarify the equipment.

• Picture

Process Columns

These columns show which processes use the equipment. An “X” in a column indicates that the equipment must be used, and a “Z” in a column indicates that the use of that equipment is optional.

Customization: Equipment necessary to perform a Customization/Activation.

Go/No Go test: Equipment necessary for Go/No Go testing. Calibration with SERP: Equipment necessary to perform a calibration with SERP. NOTE: Calibration can only be done by authorized repair centers. Repair: Equipment necessary for replacing soldered components.

1211-1566_4 Company Internal

2(25)

Equipment List, Electrical

3 Repair Equipment

Some of the required equipment will be orderable from Sony Ericsson and some equipment has to be sourced locally. The following sections are structured based on whether equipment is obtained from Sony Ericsson or from a local supplier.

3.1 Repair Equipment orderable from Sony Ericsson

Go/No Go Test

Description Part Number Comments Picture

Sony Ericsson Programming Interface (SEPI)

LTN 214 1484 The Sony Ericsson

Programming Interface (SEPI) is used in conjunction with the SEPI interface cable, the USB computer cable and battery charger to perform calibration on this product.

Customization

X

SERP

Calibration in

Repair

Sony Ericsson Programming Interface (SEPI) cable

1211-1566_4 Company Internal

KRY 101 1119/1 A battery charger needs to

be connected to this cable during calibration. (GSM Calibration only)

X

3(25)

Equipment List, Electrical

Go/No Go Test

Customization

SERP

Calibration in

Repair

Description Part Number Comments Picture

Service Tool Test Interface

Applicable for W760 only

RF Cable RPM 119 855

1206-9888 W760 only

Necessary for WCDMA Calibration. To be used with the 4921 Shield box Enclosure or any other Shield box that meets the minimum requirements stated in the Electrical Installation Instructions. The Service Tool Test Interface has two parts, one for the inside and one for the outside of the Shield box.

X

RF Cable Short

Applicable for W760 only

1211-1566_4 Company Internal

RPM 119 891 W760 only

The Short RF Cable is used to connect from the Shield box plate to the Phone.

X X

Z X

4(25)

Equipment List, Electrical

Go/No Go Test

Customization

SERP

Calibration in

Repair

Description Part Number Comments Picture

Dummy Battery

Rework Fixture for PCB LTD 260 273 Used to hold the PCB during

1208-5627 If using the Dummy Battery

to power the handset during the GNG Test or Calibration routine, you must use a high quality DC source.

repair.

Z Z Z

X

RF Probe

1211-1566_4 Company Internal

RPM 119 0201 Used together with the RF

Holder and RF Cable.

Z X

5(25)

Equipment List, Electrical

Go/No Go Test

Customization

SERP

Calibration in

Repair

Description Part Number Comments Picture

RF Holder 1207-9048 Used together with the RF

Probe and RF Cable

Z X

USB Activation Dongle NTZ 112 1071 Used for Activation in Emma

NOTE: cannot be ordered via the standard ordering process, To order contact your Regional Represenitive

X

DCU-65/USB Cable RPM 131 12 This cable is needed for

1211-1566_4 Company Internal

loading ITP software and customization/activation.

X

6(25)

Equipment List, Electrical

3.2 Repair Equipment that should be obtained from local Suppliers

Description Comments

RF Shield Package

Rohde&Schwarz RF Shield Package

• CMU-Z10 – Antenna Coupler (Partnr: 1150.0801.10)

• CMU-Z11 – RF Shield Cover (Partnr. 1150.1008.02)

Using an RF shield package is one of the options for testing the applicable product(s). Testing of the applicable product(s) can also be performed by using the combination of an RF Probe and an RF cable.

Spare parts for mobile phone fixation for R&S CMUZ10 are available for purchase from Rohde&Schwarz:

• Grid Positioning Plate – 1158.9789.00

• L-shaped bracket – 1158.9808.00

• Stabilizing pieces – 1158.9820.00

NOTE: The Rohde & Schwarz package will require the use of a precision N-type male to SMA female RF adapter to mate with the SEMC RF cable.

NOTE: If you are using a different RF Shield Package than Rohde & Schwartz, special attenuation factors for Go/No-Go test are required.

Customization

Go/No Go Test

Z

SERP

Calibration in

Repair

1211-1566_4 Company Internal

7(25)

Equipment List, Electrical

Customization

Go/No Go Test

Calibration in

SERP

Description Comments

RF adapter for RF shield box

• The adapter for a Rohde & Schwarz Shield box must be a precision Ntype male to SMA female adapter.

Willtek 4921 Shield Enclosure

With modified rear panel and N terminator

• 248718 (Wiltek Part number) Applicable for W760 only

Modified rear panel and N terminator Willtek

• 300872 (Wiltek Part number)

Applicable for W760 only Battery Charger (Standard SEMC charger applicable for W760)

This adapter is used to connect the RF shield box to the RF cable and is only required if a shield package is going to be used for testing.

Recommended source:

• Pasternack Enterprises – (949) 261-1920 or

www.pasternack.com

Part number: PE9430

W760 only

Used for WCDMA or GSM Calibration. A Service Tool Test Interface (1206-9888) is also required.

W760 only

Used with existing Willtek Shield boxes Replace rear panel with modified rear panel and place N terminator on RF connection. Remove RF coupler. A Service Tool Test Interface (1206-9888) is also required.

The battery charger needs to be connected to the Sony Ericsson Programming Interface Cable during calibration. Also used for Charger Test.

Z

X

Repair

1211-1566_4 Company Internal

8(25)