Sony XM-GTX1302 Marketing Specifications

XM-GTX1302

2/1 channel GTX amp

130 Watts x 2 RMS (20Hz-20kHz, <1%THD+N, at 4 Ohm, 14.4V)

Maximum power output of 280 Watts per channel at 4 Ohm.

170 Watts x 2 RMS (20Hz-20kHz, <1%THD+N, at 2 Ohm, 14.4V)

Maximum power output of 400 Watts per channel at 2 Ohm.

340 Watts x 1 RMS (20Hz-20kHz, <1%THD+N, at 4 Ohm mono, 14.4V)

This unit can be used as a bridging amplifier with a maximum output of 800 Watts at 4 Ohms.

Direct connection (High Level Input) can be made with the speaker output of your car audio unit if it is not equipped with RCA line output.

Hi-

Level Sensing power On feature allows the unit to be activated

without need for remote connection.

Built in 80Hz 18 dB/Oct LPF (Low Pass Filter) enables users to concentrate the power on lower frequencies.

Built in 80Hz 12 dB/Oct HPF (Hi-Pass Filter) enables users to block low frequencies to improve the audio systems efficiency.

Variable 0-10 dB 40Hz bass boost provides additional bass response at lower frequencies.

Sony Electronics Inc. • 16530 Via Esprillo • San Diego, CA 92127 • 1.800.222.7669 • www.sony.com

Last Updated: 04/13/2011

XM-GTX1302

2/1 channel GTX amp

Please visit the Dealer Source for current information at

www.sony.com/dealersource

Features

130 Watts x 2 RMS at 4 Ohms

280 Watts x 2 max power at 4 Ohms

170 Watts x 2 RMS at 2 Ohms

400 Watts x 2 max power at 2 Ohms

340 Watts x 1 RMS at 4 Ohms

800 Watts x 1 max power at 4 Ohms This unit can be used as

a bridging amplifier with a maximum output of 800 Watts at 4 Ohms.

High Level input with Sensing Power On Direct connection (High Level Input) can be made with the speaker output of your car audio unit if it is not equipped with RCA line output. Hi

Level Sensing power On feature allows the unit to be activated without need for remote connection.

80 Hz Low-pass filter, 18 dB/oct Built in 80Hz 18 dB/Oct LPF (Low Pass Filter) enables users to concentrate the power on lower frequencies.

80 Hz High-pass filter, 12 dB/oct Built in 80Hz 12 dB/Oct HPF (Hi-Pass Filter) enables users to block low frequencies to improve the audio systems efficiency.

0-10 dB Variable 40Hz Low boost Variable 0-10 dB 40Hz bass boost provides additional bass response at lower frequencies.

Specifications

Audio

Frequency Response: 5 - 50 kHz (+0/-3 dB) Input Level: 0.3 - 6.0V (RCA input) or 1.2 - 12.0V (High Level Input) Impedance: 2-8 Ohms Stereo or 4-8 Ohms Mono Operation: 2/1 channel configuration Tone Control(s): Low Pass Filter: 80Hz, 18dB/Oct

High Pass Filter: 80Hz, 12dB/Oct

Harmonic Distortion: 0.05% (at 1kHz) Low Boost: 0-10dB Variable (at 40Hz) Signal-to-Noise Ratio (dB): 93 dBA

Power

Output Power: Maximum Output: 280 Watts x2 or 800 Watts x1

(at 4 Ohms)

Current Drain: At rated output: 30A (at 4 Ohms)

Remote Input: 1 mA

Rated Output: (20Hz-20kHz, 1% THD+N, 14.4V) 130 Watts x 2

RMS (4 Ohms) 170 Watts x 2 RMS (2 Ohms) 340 Watts x 1 RMS Mono (4 Ohms)

Power Requirements: 12V DC Car Battery (Negative Ground) Internal Power Supply: OTL Output Transformerless Circuit

Pulse Power Supply

Input Voltage: 10.5-16V Power Supply Voltage

Inputs and Outputs

RCA Audio Input(s): Pin Jacks: 0.3 - 6V Audio In: RCA Pin Jacks, High Level Input Connector

Audio Out: Speaker terminals with screws

Dimensions

Weight: 6 lbs. 10 oz. Measurements: 15 1/8" x 2 1/4" x 10" (384 x 55 x 252 mm)

Supplied Accessories

Mounting Screws (4) High Level Input Cord (1) Protection cap (1)

Color:

Gray and Silver

UPC Code:

027242773059

1. CEA-2006 Compliant —

Standardized “Voluntary”

Testing & Measurement Methods for Mobile Audio

Amplifiers. This standard advocates a uniform method for determining an amplifier’s RMS power and signal

to-noise ratio. Using 14.4 volts, RMS watts are measured into a 4-ohm impedance load at 1 percent Total Harmonic Distortion (THD) plus noise, at a frequency range (for general purpose amplifiers) of 20 Hz to 20,000 Hz.

d, ZAPPIN, and the Sony and Xplōd logos are trademarks of Sony. iPod is a trademark of Apple Inc. All other trademarks are trademarks of their respective owners. Features and specifications are subject to change without notice. Non-metric weights and measures are approximate and may vary.