Sony VPL-VW995ES User Manual
4-745-124-11 (1)
Video Projector
Operating Instructions
Before operating the unit, please read this manual, supplied Quick Reference Manual
and Safety Regulations thoroughly, and retain them for future reference.
VPL-VW870ES
VPL-VW995ES
© 2018 Sony Corporation
Table of Contents
Location of Controls
Front/Right Side .......................................................... 3
Rear/Left Side/Bottom ................................................ 4
Remote Control ........................................................... 5
Connections and Preparations
Installing the Unit ....................................................... 6
Adjusting the Picture Position .................................... 6
Connecting to Video Equipment or a Computer ....... 10
Projecting
Projecting the Picture ................................................ 11
Turning Off the Power ......................................... 11
Watching 3D Video Images ...................................... 11
Using the 3D Glasses ........................................... 12
Using the Picture Position ......................................... 12
Selecting the Aspect Ratio According to the Video
Signal ..................................................................... 13
Selecting the Picture Viewing Mode ......................... 15
Using the Menus
Error Handling
Troubleshooting ........................................................ 34
About Indicators ........................................................ 36
Message Lists ............................................................ 37
Others
Updating the Software .............................................. 38
About HDR (high dynamic range) ............................ 38
About the Simulated 3D Feature ............................... 38
NOTICES AND LICENSES FOR SOFTWARE USED
IN THIS PRODUCT .............................................. 38
Specifications ............................................................ 39
Preset Signals ....................................................... 40
Input Signals and Adjustment/Setting Items ....... 41
Compatible 3D Signals ........................................ 42
3D Signals and Adjustable/Setting Items ............ 42
Aspect Mode ........................................................ 43
Motionflow .......................................................... 44
Storage Conditions of Adjustment/Setting
Items ................................................................. 45
Projection Distance and Lens Shift Range ................ 47
Dimensions ............................................................... 51
Operation through the Menus ................................... 16
Picture Menu ............................................................. 18
Advanced Picture Menu ............................................ 22
Screen Menu ............................................................. 23
Setup Menu ............................................................... 25
Function Menu .......................................................... 26
Items Locked by Settings Lock ........................... 28
Installation Menu ...................................................... 29
Information Menu ..................................................... 31
About the Preset Memory .................................... 31
Using Network Features
Displaying the Control Window of the Unit with a
Web Browser .......................................................... 32
Operating the Control Window ................................. 33
Switching the Page ............................................... 33
Setting the Access Limitation .............................. 33
Confirming the Information Regarding the
Unit ................................................................... 33
2
Location of Controls
Front/Right Side
Connectors
Indicators
a ON/STANDBY indicator (page 36)
b WARNING indicator (page 36)
Connectors
c LAN connector (page 32)
d HDMI 1/HDMI 2 connector (page 10)
e TRIGGER 1/TRIGGER 2 connector (page 29)
f IR IN connector
Inputs the signals to control the projector.
g REMOTE connector
Connects to a computer, etc. for remote control.
h USB connector (page 38)
Others
i Ventilation holes (intake)
j Remote control detector (page 6)
3
Rear/Left Side/Bottom
The buttons on the control panel function the same as those on the remote control.
Control panel
Control panel
a [/1 (On/Standby) button (page 7)
b INPUT button (page 11)
c MENU button (page 16)
d M/m/</, (arrow)/ENTER button (page 16)
e LENS button (page 6)
Others
f Remote control detector (page 6)
g Ventilation holes (exhaust)
h AC IN socket (page 7)
i Projector suspension support attaching hole
(page 52)
j Front feet (adjustable) (page 8)
k Ventilation holes (intake)
4
Remote Control
a LIGHT button
Illuminates the buttons on the remote control.
b Infrared transmitter
c ?/1 (On/Standby) button (page 7)
d INPUT button (page 11)
e CALIBRATED PRESET buttons (page 15)
f LENS ADJUSTMENT buttons (page 7)
g POSITION button (page 12)
h RESET button (page 17)
i M/m/</, (arrow)/ (enter) button
(page 16)
j MENU button (page 16)
k MOTIONFLOW button (page 19)
l ASPECT button (page 13)
m COLOR SPACE button (page 21)
n COLOR TEMP button (page 19)
o GAMMA CORRECTION button (page 20)
p 3D button (page 11)
q REALITY CREATION button (page 18)
r ADVANCED IRIS button (page 19)
s CONTRAST ENHANCER button (page 19)
t SHARPNESS +/– button (page 20)
u CONTRAST +/– button (page 19)
v BRIGHTNESS +/– button (page 19)
5
Connections and Preparations
Installing the Unit
The installation distance between the unit and a screen
varies depending on the size of the screen or whether or not
you use the lens shift features. Install this unit so that it fits
the size of your screen. For details on the distance between
the unit and the screen (the projection distance) and the
size of projected video, see “Projection Distance and Lens
Shift Range” (page 47).
1 Position the unit so that the lens is parallel to the
screen.
Top view
Screen
Adjusting the Picture Position
Project an image on the screen and then adjust the picture
position.
Remote control detector
2 Project an image on the screen and adjust the picture
so that it fits the screen (page 6).
Note
When using a screen with an uneven surface, stripes pattern may
rarely appear on the screen depending on the distance between the
screen and the unit or the zooming magnifications. This is not a
malfunction of the unit.
Tips
•The ?/1 (On/Standby), INPUT, and MENU buttons on the side
panel of the unit have the same functions as those on the remote
control. The M/m/</, (arrow)/ENTER button of the unit has
the same function as the M/m/</, (arrow)/ (enter) button
on the remote control. The LENS button functions the same way
as the LENS ADJUSTMENT (FOCUS, ZOOM, SHIFT) buttons
on the remote control.
• When adjusting the lens, each time you press the LENS button on
the unit, the lens adjustment function switches between “Lens
Focus,” “Lens Zoom” and “Lens Shift.”
Note
Depending on the installation location of the unit, you may not be
able to control it with the remote control. In this case, point the
remote control at the remote control detector of the unit or the screen.
6
1 After connecting the AC power cord to the unit, plug
the AC power cord into a wall outlet.
The ON/STANDBY indicator lights in red and the
unit goes into standby mode.
Lights in red.
2 Press the ?/1 (On/Standby) button to turn on the unit.
The ON/STANDBY indicator flashes in green, and
then lights in green.
Flashes in green for
tens of seconds and
then lights in green.
3 Adjust the focus.
Press the LENS ADJUSTMENT (FOCUS) button to
display the Lens Focus adjustment window (test
pattern). Then adjust the focus of the picture by
pressing the M/m/</, button.
4 Adjust the picture size.
Press the LENS ADJUSTMENT (ZOOM) button to
display the Lens Zoom adjustment window (test
pattern). Then adjust the size of the picture by
pressing the M/m/</, button.
To make the picture larger, press M/,.
To make the picture smaller, press m/<.
5 Adjust the picture position.
Press the LENS ADJUSTMENT (SHIFT) button to
display the Lens Shift adjustment window (test
pattern). Then adjust to the proper position of the
picture by pressing the M/m/</, button.
Tips
• When “Lens Control” is set to “Off” on the Installation menu,
you cannot adjust the focus, the picture size or the proper position
by pressing the FOCUS, ZOOM or SHIFT button (page 29).
• When “Test Pattern” is set to “Off” on the Function menu, the
test pattern is not displayed (page 27).
Note
Adjust the lens by using buttons on the remote control or the control
panel of the unit. Never make adjustments by directly turning the
lens with your hands, which may cause damage or malfunction to the
unit.
Tip
Whenever you press the button, the test pattern disappears.
Note
When adjusting the picture position, do not touch the lens unit,
otherwise your fingers may be pinched by the moving parts.
7
To adjust the horizontal position
Press </,.
The picture projected on the screen moves right or left by
a maximum of 31% of the screen width from the center of
the lens.
Note
The range to move the picture projected on the screen can be
adjusted only within the octagon area illustrated below. For details,
see “Projection Distance and Lens Shift Range” (page 47).
Range of movement of the projected picture
Top view
31% 31%1 screen width
: Picture position when moving the
picture to the left at maximum
: Picture position when moving the
picture to the right at maximum
Press the RESET button on the remote control while the Lens Shift
adjustment window is displayed, the horizontal position returns to
the center of the lens (factory default position). The zoom and focus
are not changed.
0.8V
0.31H
Projected Picture
0.8V
H: Width of the projected picture
V: Height of the projected picture
0.31H
To adjust the tilt of the installation surface
If the unit is installed on an uneven surface, use the front
feet (adjustable) to keep the unit level.
To adjust the vertical position
Press M/m.
The picture projected on the screen moves up by a
maximum of 80% or moves down by a maximum of 80%
of the screen height from the center of the lens.
Side view
80%
1 screen
height
80%
: Picture position when moving the
picture upward at maximum
: Picture position when moving the
picture downward at maximum
Turn to adjust.
Front feet (adjustable)
Notes
• If the unit is tilted up or down, the projected image may be
trapezoidal.
• Be careful not to catch your finger when turning the front feet
(adjustable).
8
Lens adjustment window (test pattern)
1.78:1 (16:9)
1.33:1 (4:3)
2.35:1
1.85:1
The dashed lines show the screen sizes of each
aspect ratio.
9
Connecting to Video Equipment or a Computer
You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/recorder, or PlayStation®
equipped with HDMI output to the HDMI input of the unit.
When making connections, be sure to do the following:
• Turn off all equipment before making any connections.
• Use the proper cables for each connection.
• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When
pulling out a cable, be sure to pull it out from the plug, not the cable itself.
• Refer to the operating instructions of the connected equipment.
Computer
Right side of the unit Equipment with HDMI output connectors
to HDMI input
HDMI cable (not supplied)
: Video signal flow
Notes
• Use a Premium High Speed HDMI cable. If using a cable other than a Premium High Speed cable, 4K video images may not be properly
displayed.
• When connecting an HDMI cable to the unit, make sure the V mark on the upper part of the HDMI input of the unit and the v mark on the
connector of the cable are faced at each other.
• If the picture from equipment connected to the unit with an HDMI cable is not correct, check the settings of the connected equipment.
• If you set your computer, such as a notebook type, to output the signal to both computer’s display and this equipment, the picture of the
equipment may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer’s
operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer.
Use a Premium High Speed HDMI cable on which
the cable type logo is specified.
AV amplifier
to HDMI output
Speakers
10
.
Projecting
Projecting the Picture
1 Turn on both the unit and the equipment connected to
the unit.
2 Press INPUT to display the input palette on the
screen.
3 Select the equipment from which you want to display
images.
Press INPUT repeatedly or press M/m/ (enter) to
select the equipment from which to project.
Tips
• When “Status” is set to “Off” on the Setup menu, the input
palette does not appear. Press the INPUT button to switch between
input terminals sequentially.
• You can change the language for the menu and on-screen displays
in “Language” on the Setup menu (page 25).
Turning Off the Power
1 Press the ?/1 (On/Standby) button.
The message “POWER OFF?” appears.
2 Press the ?/1 (On/Standby) button again before the
message disappears.
The ON/STANDBY indicator flashes in green and the
fan continues to run to reduce the internal heat.
The fan stops and the ON/STANDBY indicator
changes from flashing green to remaining red.
The power is turned off completely, and you can
disconnect the AC power cord.
Watching 3D Video Images
You can enjoy powerful 3D video images, such as from 3D
games and 3D Blu-ray Discs, using the optional Active 3D
Glasses (TDG-BT500A).
1 Turn on the HDMI equipment for 3D compatibility
connected to the unit, then play the 3D content.
For details on how to play 3D content, refer to the
operating instructions for the connected equipment.
2 Turn on the unit and project the 3D video image.
For details on how to project the image, see
“Projecting the Picture” (page 11).
3 Turn on the 3D glasses, and then put them on so that
they fit comfortably.
For details on how to use the 3D glasses, see “Using
the 3D Glasses” (page 12).
Tip
The factory default setting for “2D-3D Display Sel.” is “Auto” to
allow projecting 3D video images automatically when the unit
detects 3D signals.
Notes
• It may not be possible to display 3D video image, depending on
the type of signal. Set the “2D-3D Display Sel.” to “3D,” and “3D
Format” to “Side-by-Side” or “Over-Under” to suit the format of
the 3D content you want to watch (page 26).
• Use the 3D glasses within the communication range (page 12).
• There are differences in perception of 3D video images among
individuals.
• When the temperature of the usage environment is low, the 3D
effect may be diminished.
Note
Never disconnect the AC power cord while the indicator is flashing.
Tip
You can turn off the unit by holding the ?/1 (On/Standby) button for
about 1 second, instead of performing the above steps.
Adjusting/Setting the 3D functions
You can adjust/set the 3D functions by pressing the 3D
button on the remote control or with the “3D Settings” of
the Function menu. For details, see “3D Settings”
(page 26).
11
Using the 3D Glasses
Using the Picture
1 Turn on the 3D glasses, and register them on the unit.
For details on how to register the 3D glasses, refer to
the operating instructions supplied with the 3D
glasses.
2 Put on the 3D glasses.
3 Turn toward the screen.
Precautions for use
Misoperation may occur if:
• The viewing position is too far from the projector
• There are other communication devices, such as a
wireless LAN (IEEE802.11 b/g/n) or a microwave with
a bandwidth of 2.4 GHz, near the unit
3D glasses communication range
The following figure indicates the communication range of
the 3D glasses. If you try to watch 3D video images from
a distance greater than the communication range or install
the unit outside the communication range, the 3D glasses
may not be able to display the images properly. Also, the
distance varies depending on the environment of the room
and installation environment of the unit.
Top or side view
Projector
10 m
Position
You can store up to five combinations of lens settings
(focus, picture size, picture position), aspect ratio, and
blanking. These settings can be recalled.
In the factory preset setting, the Picture Position is not
stored.
1 Press POSITION.
The Picture Position selecting palette is displayed.
2 Press POSITION repeatedly, or press M/m/ to
select the position.
The settings of the position selected is recalled.
Store or delete lens settings, aspect ratio, and blanking
in the “Picture Position” of the Screen menu
(page 23).
The position where the lens settings, aspect ratio, and
blanking are not stored is displayed as “---.”
10 m
10 m 10 m
12
Image of the lens moving
In the example below, the images with aspect ratio of
1.78:1 (16:9) and 2.35:1 are projected on a 2.35:1 screen.
Selecting the Aspect Ratio According to the Video Signal
When a 1.78:1 (16:9) image is input
When a 2.35:1 image is input
Press the POSITION button.
The 2.35:1 image expands to fill the screen.
Notes
• After you have selected and confirmed the lens position, the lens
starts to move. Do not touch, or place anything near, the lens,
otherwise it may cause injury or a malfunction.
• If you press any button on the remote control or the unit while the
lens is moving, the lens stops. In this case, select the lens position
again or adjust the lens manually.
• The Picture Position function is not guaranteed to reproduce the
lens settings precisely.
• When you use the subtended screen angle of two or more aspects
using lens zoom, install the unit within the specified parameters
referring to “Projection distance” (page 48). With some setting
positions, the range of lens shift may be restricted, even though the
unit is installed within the specified parameters.
You can select an aspect ratio best suited for the video
signal received.
Press ASPECT.
Each time you press the button, you can select the “Aspect”
setting.You can also select it using the menu (page 23).
ASPECT
button
Original image
1.85:1
Recommended setting and
resultant images
1.85:1 Zoom
13
Squeezed 1.85:1
2.35:1 Zoom
2.35:1
Squeezed 2.35:1
Original image
1.78:1 (16:9)
1.33:1 (4:3)
1.33:1 (4:3) with side panels
Recommended setting and
resultant images
Normal
V Stretch
Notes on switching the “Aspect” setting
• Select the aspect mode taking into account that changing
the aspect ratio of the original picture will provide a
different look from that of the original image.
• Note that if the unit is used for profit or for public
viewing, modifying the original picture by switching the
aspect may constitute an infringement of the rights of
authors or producers, which are legally protected.
2.35:1
16:9
Squeezed
When using an anamorphic lens
Squeeze
When using an anamorphic lens
Stretch
Note
Selectable aspect modes vary depending on the input signal
(page 43).
14
Selecting the Picture Viewing Mode
You can select the picture viewing mode that best suits the
type of video source or room conditions.
You can save and use different preset modes for 2D/3D
respectively.
Press one of the CALIBRATED PRESET buttons.
CALIBRATED PRESET buttons
Setting items Description
CINEMA FILM 1 Picture quality suited to reproducing the
CINEMA FILM 2 Picture quality suited to reproducing the rich
REF A picture quality setup suitable for when you
TV Picture quality suited for watching TV
PHOTO Ideal for projecting still images taken with a
GAME Picture quality suited to gaming, with well-
BRT CINE Picture quality suited for watching movies in
BRT TV Picture quality suited for watching TV
USER Adjusts the picture quality to suit your taste
highly dynamic and clear images typical of
master positive film.
tone and color typical of a movie theater,
based on the “CINEMA FILM 1.”
want to reproduce faithfully the original
image quality, or for enjoying image quality,
without any adjustment.
programs, sports, concerts, and other video
images.
digital camera.
modulated colors and fast response.
a bright environment, such as a living room.
programs, sports, concerts, and other video
images in a bright environment, such as a
living room.
then saves the setting. The factory default
setting is the same as “REF.”
15
Using the Menus
Note
The menu displays used for the explanation may be different from the actual menu display.
Pop-up menu
Operation through the Menus
The unit is equipped with an on-screen menu for making
various adjustments and settings. If you select an item
name followed by an arrow (B), the next menu window
with setting items appears.
1 Press MENU.
The menu window appears.
2 Press M/m to select a menu item, and press , or .
The items that can be set or adjusted with the selected
menu appear. The item presently selected is shown in
white.
Setting items
Setting menu
Adjustment menu
3 Press M/m to select an item you want to set or adjust
and press , or .
The setting items are displayed in a pop-up menu, in
a setting menu, in an adjustment menu or in the next
menu window.
Next menu window
Setting items
16
4 Make the setting or adjustment of an item.
When changing the adjustment level
Press M/, to increase the value, and press m/< to
decrease the value.
Press to store the setting and restore the original
menu screen.
When changing the setting
Press M/m to change the setting.
Press to restore the original screen.
You can restore the original screen using <
depending on the selected item.
To clear the menu
Press MENU.
To reset the picture that has been adjusted
Select “Reset” from the Picture menu.
When the screen display appears, select “Yes” using <
and press .
All of the following settings are reset to its factory preset
value:
“Reality Creation,” “Cinema Black Pro,” “Motionflow,”
“Contrast,” “Brightness,” “Color,” “Hue,” “Color Temp.,”
“Sharpness,” and “Expert Setting” on the Picture menu
To reset the items that have been adjusted
Select an item in the menu screen, and display the pop-up
menu, the setting menu, or the adjustment menu.
Press RESET on the remote control to reset only the
selected settings to its factory preset value.
Note
The RESET button on the remote control is available only when the
adjustment menu or the setting menu is selected.
17
Loading...