Sony VPL-SX125, VPL-SW125EBPAC User Manual

Data
Projector

4-283-582-11 (2)

Operating Instructions

Before operating the unit, please read this manual and supplied Quick Reference Manual
thoroughly and retain it for future reference.

VPL-SX125
VPL-SW125

Not all models are available in all countries and area. Please check
with your local Sony Authorized Dealer.

© 2011 Sony Corporation

Table of Contents

Overview

Location and Function of Controls .... 3

Main unit ...................................... 3

Connector Panel ...........................4

Remote Commander and Control

Panel ..........................................5

Preparation

Connecting the Projector ................... 7

Connecting a Computer ................7

Connecting a Video equipment .... 8

Connecting an External Monitor and

Audio Equipment .................... 10

Projecting/Adjusting an
Image

Projecting an Image ......................... 11

Adjusting the Projected

image ....................................... 12

Turning Off the Power ................14

Adjustments and Settings
Using a Menu

Network

Using Network Features ...................27

Displaying the Control Window of

the Projector with a Web

Browser ...................................27

Confirming the Information

regarding the Projector ............28

Operating the Projector from a

Computer .................................28

Making the Network Settings .....28

Using the e-mail report

Function ...................................28

Others

Indicators ..........................................30

Messages List ...................................31

Troubleshooting ................................32

Replacing the Lamp ..........................34

Cleaning the Air Filter ......................36

Specifications ...................................37

Projection Distance ...........................42

Dimensions .......................................46

Index .................................................48

Using a MENU ................................15

The PICTURE SETTING Menu ...... 16

The INPUT SETTING Menu .......... 17

The SET SETTING Menu ............... 21

The MENU SETTING Menu .......... 23

The INSTALL SETTING Menu ...... 24

The INFORMATION Menu ............26

2

Table of Contents

B Overview

q

43

q

Location and Function of Controls

Main unit

1

0
6

qa

a

a Projection lens

b Focus ring (page 12)

c Lamp cover (page 34)

d Air filter cover (page 36)/

Ventilation holes (intake)

e Ventilation holes (intake)

f Ventilation holes (exhaust)

2

7

5
qa

g LAMP/COVER indicator

(page 30)

h Control panel (page 5)

i Connector panel (page 4)

j Remote control detector

k Adjuster (page 12)

l Speaker

m Security lock

Connects to an optional security cable
manufactured by Kensington.
For details, visit Kensington’s web site.
http://www.kensington.com/

n Security bar

Connects to a commercially available
security chain or wire.
If it is difficult to pull out, pull out the
Security bar using a screwdriver.

Overview

8
9
qs
qd

f

Caution

Do not place anything near the ventilation
holes as this may cause internal heat
buildup. Do not place your hand near the
ventilation holes and the circumference as
this may cause injury.

Security bar

Location and Function of Controls

3

Connector Panel

VPL-SX125

4

1

5

9

VPL-SW125

4

1

5

9

Input (pages 7, 8)

a INPUT A

Video: RGB/YPBPR input connector

(RGB/YPBPR)

Audio: Audio input connector (AUDIO)

b INPUT B (VPL-SX125 only)

Video: RGB input connector (RGB)
Audio: Audio input connector (AUDIO)

c INPUT B (VPL-SW125 only)

Video: HDMI input connector (HDMI)
Audio: HDMI input connector (HDMI)

d S VIDEO (S VIDEO IN)

Video: S video input connector
Audio: Audio input connector (L

[MONO] AUDIO/R)

e VIDEO (VIDEO IN)

Video: Video input connector
Audio: Audio input connector (L

[MONO] AUDIO/R)

Note

The audio inputs of S VIDEO and VIDEO are
shared.

2 6 8

6 3 8

7

7

Output (page 10)

f OUTPUT

Video: Monitor output connector

(MONITOR)

Audio: Audio output connector

(AUDIO)

Note

This connector outputs the projected image or
audio. The image is output as a computer signal
input from the RGB input connector (INPUT
A/INPUT B (INPUT B is available only for
VPL-SX125)) or a video signal input from the
YP

BPR input connector (INPUT A).

Others

g RS-232C connector

RS-232C compatible control connector.
Connects the computer’s RS-232C
connector and the RS-232C cross cables.

h LAN connector (page 27)

i AC IN (∼) socket

Connects the supplied AC power cord.

4

Location and Function of Controls

Remote Commander and Control Panel

7

Remote Commander

4

INPUT

APA ECO MODE

2

3

4

Control Panel

123 3 6

MENU

RETURN

ASPECT

D ZOOM

KEYSTONE

VOLUME

ENTER

PATTERN

FREEZE

RESET

PIC MUTING

AUDIO MUTING

1
6

5

a Turning on the power/Going to

standby mode

?/1 (On/Standby) key

b Selecting an input signal

(page 11)

INPUT key

c Operating a menu (page 15)

MENU key
RESET key
ENTER /V/v/B/b (arrow) keys
RETURN key

This function is not provided in this
projector.

d Adjusting the image (page 12)

ASPECT key
KEYSTONE key
PATTERN key

This function is not provided in this
projector.

APA (Auto Pixel Alignment) key

Note

* Use this key when inputting a computer

signal via the RGB input connector
(INPUT A/INPUT B (INPUT B is
available only for VPL-SX125)).

Overview

*

e Using various functions during

projecting

D ZOOM (Digital Zoom) +/– key

*1

Enlarges a portion of the image while
projecting.

1 Press the D ZOOM + key to display

the digital zoom icon on the projected
image.

2 Press the V/v/B/b keys to move the

digital zoom icon to the point on the
image you wish to enlarge.

3 Press the D ZOOM + key or the D

ZOOM – key repeatedly to change the
enlargement ratio. The image can be

enlarged up to 4 times.
Press the RESET key to restore the
previous image.

Location and Function of Controls

5

PIC MUTING key

Cuts off the image. Press again to restore
the image.

AUDIO MUTING key

Mutes the audio output. Press again to
restore the previous volume.

VOLUME +/– key

For adjusting the volume output.

FREEZE key

*2

Pauses a projected image. Press again to
restore the image.

Notes

*1: Use this key when inputting a

computer signal. But it may not be
used depending on the resolution of
the input signal.

*2: Use this key when inputting a

computer signal.

f Setting the energy–saving mode

easily

ECO MODE key

Energy-saving mode can be set easily.
Energy-saving mode consists of “Lamp
Mode,” “Power Saving Mode” and
“Standby Mode.”

1 Press the ECO MODE key to display

the ECO Mode menu.

ECO Mode Menu

ECO Mode

ECO

User

Sel: Exit:

2 Press the V/v key or ECO MODE key

to select ECO or User mode.
ECO: Sets each mode to the optimum

energy-saving value.
Lamp Mode: Low
Power Saving Mode: Standby
Standby Mode: Low
(go to step 6)

User: Sets each item of the energy-

saving mode menu as you desire
(go to step 3).

3 Select “User” then press the b key.

The setting items appear.

User

Lamp Mode Standard

Power Saving Mode Off

Standby Mode Low

Sel: Set: Exit:

4 Press the V/v key to select the item

then press the ENTER key.

5 Press the V/v key to select the setting

value.

6 Press the ENTER key to restore the

User screen.
For details on ECO Mode settings, see
“Lamp Mode” (page 24) and “Standby

*4

” (page 24) on the INSTALL

Mode
SETTING menu and “Power Saving
Mode” (page 21) on the SET SETTING
menu.

Others

g Infrared transmitter

About Remote Commander operation

• Direct the Remote Commander toward the
remote control detector.

• The shorter the distance between the
Remote Commander and the projector is,
the wider the angle within which the
Remote Commander can control the
projector becomes.

• Make sure that nothing obstructs the
infrared beam between the Remote
Commander and the remote control
detector on the projector.

6

Location and Function of Controls

B Preparation

Connecting the Projector

Notes

• Make sure all the equipment is powered off when connecting the projector.

• Use the proper cables for each connection.

• Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or
cause a malfunction. When pulling out a cable, be sure to grip it by the plug, not the cable itself.

• For more information, refer also to the instruction manuals of the equipment you are connecting.

• Use a no-resistance audio cable.

Connecting a Computer

Connection with a computer is explained for each input signal.

INPUT A/INPUT B (INPUT B is available only for VPL-SX125)

For connecting a computer with an RGB output connector.

Mini D-sub 15-pin cable (supplied)

RGB output

Computer

connector

Audio output
connector

Preparation

Audio cable (Stereo mini plug) (not supplied)

Note

It is recommended that you set the resolution of your computer to 1024 × 768 pixels (VPL-SX125)
or 1280 × 800 pixels (VPL-SW125) for the external monitor.

Connecting the Projector

7

Connecting a Video equipment

Connections with a VHS video deck, DVD player, or BD player are explained for each input
signal.

S VIDEO IN

For connecting video equipment with an S-video output connector.

S video cable
(not supplied)

S video output

connector

Video equipment

VIDEO IN

For connecting video equipment with a video output connector.

Video equipment

Audio output

connector

Audio cable (Phono plug × 2) (not supplied)

Video cable (not supplied)

Video output

connector

Audio output

connector

Audio cable (Phono plug × 2) (not supplied)

INPUT A

For connecting video equipment with a YPBPR output connector.

Component – Mini D-sub 15-pin cable (not supplied)

YP

BPR output

connector

Audio output

Video equipment

8

Connecting the Projector

connector

Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)

INPUT B (VPL-SW125 only)

For connecting video equipment with an HDMI output connector.

Computer

Video equipment

Notes

DVI-D output

connector

HDMI output

connector

HDMI-DVI-D cable
(not supplied)

HDMI cable
(not supplied)

• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.

• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal
or CEC (Consumer Electronics Control) Signal.

Preparation

Connecting the Projector

9

Connecting an External Monitor and Audio Equipment

OUTPUT

Projected images and input audio can be output to display equipment such as a monitor and
audio equipment such as speakers with a built-in amplifier. When an audio cable is connected
to the audio output connector, no sound will be heard from the built-in speaker.

Display equipment

Audio equipment

Note

RGB input

connector

Audio input

connector

Mini D-sub 15-pin
cable (supplied)

Audio cable
(stereo mini plug)
(not supplied)

Projected images and audio can be output. The image is output only as a computer signal input from
the RGB input connector (INPUT A/INPUT B (INPUT B is available only for VPL-SX125)) or a
video signal input from the YP

BPR input connector (INPUT A).

10

Connecting the Projector

B Projecting/Adjusting an Image

Projecting an Image

The size of a projected image depends on the distance between the projector and screen. Install
the projector so that the projected image fits the screen size. For details on projection distances
and projected image sizes, see

“Projection Distance” (page 42).

5

35

4

Computer

6

Video equipment

1 Plug the AC power cord into the wall

outlet.

2 Connect all equipment to the projector

(page 7).

3 Press ?/1 to turn on the unit.

4 Turn on the connected equipment.

5 Select the input source.

Each time you press the INPUT key on
the projector, the input signal switches.
Press the INPUT key repeatedly to select
an image to be projected.

2

Projector

1

Wall outlet

6 Switch your computer to output to

external display by changing your
computer’s setting.

How to switch the computer to output to
the projector varies, depending on the
type of computer.

(Example)

+

7 Adjust the focus and position of the

projected image (page 12).

Projecting/Adjusting an Image

Projecting an Image

11

Adjusting the Projected image

Focus Position

Adjuster adjustment button

Adjusting the tilt of the projector with the adjusters

You can adjust the height of the projector
using the adjusters.
By changing the slope of the projector with
adjusters, you can adjust the position of the
projected image.

Notes

• Be careful not to let the projector down on your fingers.

• Do not push hard on the top of the projector with the adjuster extended. It may cause malfunction.

12

Projecting an Image

Changing the aspect ratio of the projected image

Press ASPECT on the remote commander to change the aspect ratio of the projected image.
You can also change the setting in Aspect of the INPUT SETTING menu (page 17, page 19).

Correcting trapezoidal distortion of the projected image (Keystone feature)

Keystone feature may not work automatically when the screen is tilted. In this case, set
keystone manually.

1 Press KEYSTONE on the remote

commander or select V Keystone in the
INSTALL SETTING menu.

2 Use V/v/B/b to set the value. The higher

the setting, narrower the top of the
projected image. The lower the setting, the
narrower the bottom.

Note

Since the Keystone adjustment is an electronic
correction, the image may be deteriorated.

Increase the number
towards plus

Increase the number
towards minus

Projecting/Adjusting an Image

Automatically adjusts Phase, Pitch and Shift of projected image while a
signal is input from a computer (APA (Auto Pixel Alignment))

Press APA on the remote commander. Press again to cancel during the setting.
If Smart APA is set to On, executes APA automatically when a signal is input (page 21).

Projecting an Image

13

Turning Off the Power

1 Press the ?/1 key on the main unit or the Remote Commander.

The message appears. Press it again according to the message.

2 Unplug the AC power cord from the wall outlet.

After step 1, the fan continues to run for a while to reduce internal heat, however, you may
also unplug the AC power cord before the fan stops.

To clear the confirmation message

The message disappears if you press any key other than the ?/1 key on the main unit or the
Remote Commander, or if you do not press any key for a while.

To turn off without displaying confirmation message

Hold the ?/1 key on the main unit pressed for a few seconds.

14

Projecting an Image

B Adjustments and Settings Using a Menu

Using a MENU

Note

The menu displays used for the explanation below may be different depending on the model you are
using.

1 Press the MENU key to display the

menu.

2 Select the setting menu.

Use the V or v key to select the setting
menu then press b or ENTER

Setting menu

PICTURE SETTING Input-A

Picture Mode Presentation
Adjust Picture...

Volume 30

Sel: Set: Back: Eixt:

key.

3 Select the setting item.

Use the V or v key to select the setting
menu then press b or ENTER key.
To return to the selection screen of the
setting menu, press the B key.

Setting items

PICTURE SETTING Input-A

Picture Mode Presentation

Adjust Picture...

Volume 30

factory preset value, press the RESET
key during setting or adjusting.

Selecting items

PICTURE SETTING Input-A

Picture Mode Standard

Adjust Picture...

Volume 30

Sel: Set: Back: Eixt:

Dynamic
Standard
Game
Living
Cinema

Presentation

Using the setting menu

Press the V or v key to select the item.
Press the ENTER key to restore the
previous screen.

Using the adjustment menu

To increase the number, press the V or b
key and to decrease the number, press
the v or B key. Press the ENTER key to
register the setting. The previous screen
is restored.

90

5 Press the MENU key to clear the

menu.

The menu disappears automatically if no
key is pressed for a while.

Adjustments and Settings Using a Menu

Sel: Set: Back: Eixt:

4 Make the setting or adjustment for the

selected item.

Menu operation differs depending on the
setting item. If the next menu window is
displayed, select the item according to
the operations in step 3.
To return to the selection screen of the
setting items, press the B key. Also, to
reset the setting value of an item to its

Using a MENU

15

The PICTURE SETTING Menu

For adjusting the picture for each input signal.

Items Item descriptions

Picture Mode Dynamic: Emphasizes the contrast to produce a “dynamic and vivid” picture.

Adjust Picture... The unit can store the setting values of the following sub menu items for each

Contrast The higher the setting, the greater the contrast. The lower the setting, the lower

Brightness The higher the setting, the brighter the picture. The lower the setting, the darker

Color

*2 *4 *5

Hue

Sharpness*2The higher the setting, the sharper the picture. The lower the setting, the softer

Color
Temp .

DDE
(Dynamic
Detail
Enhancer)

*6

Standard: Makes the picture be natural and well balanced.
Game: Select for viewing game picture.
Living: Select for viewing sports, music, and digital video camera picture.
Cinema: Select for viewing film-like picture.
Presentation

picture mode separately.

the contrast.

the picture.

*2 *4

The higher the setting, the greater the intensity. The lower the setting, the lower
the intensity.

The higher the setting, the more greenish the picture becomes. The lower the
setting, the more reddish the picture becomes.

the picture.

High/Middle/Low: The higher the temperature, the more bluish the picture.

*3

The lower the temperature, the more reddish the picture.

Off: Plays back the interlace format without conversion.
Progressive: Plays back the video signal of the interlace format converting to

progressive.
Film: Precisely reproduces the image from a film source to suit the original
film source.

*1

: Makes the picture bright to suit for a presentation.

Gamma
Mode

Volume The higher the setting, the higher an audio volume and the lower the setting, the

Notes

*1: When a computer signal is input, this option is available.
*2: When a video signal is input, this option is available.
*3: When “Picture Mode” is set to the item other than “Presentation,” this option is available.
*4: When a B & W signal is input, this option is not available.
*5: When an analog TV signal is input, this option may not available, depending on the color system.
*6: When a progressive signal or a 1080i signal is input, this option is not available.

16

The PICTURE SETTING Menu

Graphics: Improves the reproduction of halftones. Photos can be reproduced

*1

in natural tones.
Text: Contrasts black and white. Suitable for images that contain lots of text.

lower the audio volume. The audio output level will work simultaneously.

The INPUT SETTING Menu

For adjusting the size, position, and aspect ratio of the projected image for each input signal.

Items Item descriptions

Adjust Signal Adjusts the image of computer signal. Use this item if the edge of the image

Dot Phase

H Size

*2

Shift

*3

Aspect

When the
computer
signal is
input

When the
video signal
is input
(VPL­SX125)

When the
video signal
is input
(VPL­SW125)

Over Scan

*4 *5

is cut and reception is bad.

*1

Adjusts the dot phase of the display pixel and the input signal. Set to the
value where looks clearest.

*1

The higher the setting, the wider the horizontal image elements (pitch). The
lower the setting, the narrower the horizontal image elements (pitch).

H: The higher the setting, the farther right the image is projected on the
screen. The lower the setting, the image farther left.
V: The higher the setting, the farther up the image is projected on the screen.
The lower the setting, the image farther down.

Changes the aspect ratio of the projected image (page 19).

Normal: Displays the image on the center point of the projected image
without changing the resolution of the input signal or enlarging the image.

Full1: Displays the image to fit the maximum projected image size without
changing the aspect ratio of the input signal.

Full2: Displays the image to fit the maximum projected image size.

*4

Full3

: Displays a 1280 × 760 dot picture on the screen without changing

the aspect ratio of the original image.

4:3: Displays the image to fit the maximum projected image size with an
aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size with an
aspect ratio fixed to 16:9.

Zoom: Display the center point of the projected image to zoom.

Normal: Displays the image with an aspect ratio fixed to 4:3.
Full: Displays the image with an aspect ratio fixed to 16:9.
Zoom: Displays the image to enlarge without changing the aspect

ratio of the original image.

Wide Zoom: Displays the image to enlarge with minimum distortion.

On/Off: When set to “On”, the outer edges of the picture will be hidden.

Select this setting when noise appears along the edge of the picture.

Adjustments and Settings Using a Menu

Notes

*1: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B

(INPUT B is available only for VPL-SX125)).

*2: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B

(INPUT B is available only for VPL-SX125)) or a video signal is input from the YP

BPR input

connector (INPUT A).

*3: • Note that if the projector is used for profit or for public viewing, modifying the original picture

by switching to the aspect mode may constitute an infringement of the rights of authors or
producers, which are legally protected.

• Depending on the input signal, setting items for aspect ratio or some other setting items cannot
be set in some cases, or changing the aspect ratio setting may have no effect.

The INPUT SETTING Menu

17

• A part of the image may be displayed in black, depending on the setting item.
*4: VPL-SW125 only.
*5: Available when a video signal is input from the YP

input connector (INPUT B). (Available for VPL-SW125 only.)

BPR input connector (INPUT A) or the HDMI

18

The INPUT SETTING Menu

Aspect

VPL-SX125

Input signal Recommended

Computer signal

setting value and

projected image

(4:3) (Full1)

(16:9) (Full1)

(16:10) (Full1)

(4:3) (4:3)*3

*1

*1 *2

*1 *2

*1: If you select “Normal,” the image is

projected in the same resolution as the
input signal without changing the aspect
ratio of the original image.

*2: If you select “Full2,” the image is projected

to fit the projected image size, regardless
of the aspect ratio of the image.

*3: Depending on the input signal, the

projected image may be projected as
illustrated below. In this a case, select
“16:9.”

*4: Depending on the input signal, the image

may be projected as illustrated below. In
this a case, select “Zoom.”

Adjustments and Settings Using a Menu

(16:9) (16:9)

*4

Video signal

The INPUT SETTING Menu

19

VPL-SW125

Input signal Recommended

setting value and

projected image

(4:3) (Full1)

(16:9) (Full1)

*1 *2 *3

*1 *2 *3

*1: If you select “Normal,” the image is

projected in the same resolution as the
input signal without changing the aspect
ratio of the original image.

*2: If you select “Full2,” the image is projected

to fit the projected image size, regardless
of the aspect ratio of the image.

Computer signal

(16:10) (Full1)

*3

*3: If you adjust the projected image position

using an image with 16:9 aspect ratio and
then switch the input source to 4:3 image,
the top and bottom edge of the image may
be hidden. In this a case, select “Full3.”

(4:3) (Normal)

*4 *5

*4: Depending on the input signal, the

projected image may be projected as
illustrated below. In this a case, select
“Full.”

(16:9) (Full)

Video signal

*5: Depending on the input signal, the image

may be projected as illustrated below. In
this a case, select “Zoom.”

20

The INPUT SETTING Menu

The SET SETTING Menu

The SET SETTING menu is used for setting various functions of the projector.

Items Item descriptions

Smart APA On/Off: When set to “On,” executes APA automatically when a signal

Auto Input Search On/Off: When set to “On,” the projector detects input signals in the

Input-A Signal Sel. Auto/Computer/Component/Video GBR: When set to “Auto,”

Color System Auto/NTSC3.58/PAL/PAL-60/SECAM/NTSC4.43/PAL-M/PAL-N:

Power Saving Mode Lamp Cutoff: The lamp turns off automatically and power

Panel Key Lock On/Off: When set to “On,” locks all the control panel keys of the

CC Display CC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed

Network Setting

IP Address Setup Auto (DHCP): The IP address is assigned automatically from the

IP Address/Subnet
Mask/Default
Gateway/DNS
Server/Apply

Lamp Timer Reset When replacing the lamp, resets the lamp timer (page 34).

*4

*1 *2

is input.

following order: Input-A/Input-B/Video/S Video. It indicates the input
channel when the power is turned on or the INPUT key is pressed.

selects the type of video signal input automatically when “Input-A” is
selected with the INPUT key.

When set to “Auto,” selects the color system automatically when “S
Video” or “Video” is selected with the INPUT key.

consumption is reduced if no signal is input for 10 minutes. The lamp
lights again when a signal is input or any key is pressed. In Lamp
Cutoff, the ?/1 key lights in orange (page 30).
Standby: The power will be turned off automatically and the projector
goes to Standby mode if no signal is input for 10 minutes.
Off: The Power Saving Mode is canceled.

projector. However, you can operate the following when set to “On”:

• Press and hold the ?/1 key for approximately 10 seconds during

Standby mode.
c The projector turns on.

• Press and hold the ?/1 key for approximately 10 seconds during

power on.
c The projector goes to Standby mode.

• Press and hold the MENU key for approximately 10 seconds during
power on.
c “Panel Key Lock” is set to “Off” and enables operation of all keys

on the projector.

caption service (Captions or Text).
Off: Closed caption does not appear.

DHCP server such as a router.
Manual: To specify the IP Address manually.

When “Manual” is selected for “IP Address Setup,” select the item
with the B or b key and input the value with V or v key. When all
items are entered, select “Apply” then press the ENTER key. The
entered settings will be registered.

*3

*3

Adjustments and Settings Using a Menu

The SET SETTING Menu

21

Notes

*1: Executes APA when a computer signal is input via the RGB input connector (INPUT A/INPUT

B (INPUT B is available only for VPL-SX125)).

*2: If the projected image includes large amount of black portion around it, the APA function will

not work properly and a part of the image may not be displayed on the screen and also optimum
image cannot be obtained, depending on the type of input signal. In this case, adjust the “Dot
Phase,” “H size,” and “Shift” items manually.

*3: The image may not be adjusted properly depending on the type of input signal. In such a case,

adjust it manually to suit to the connected equipment.

*4: “Network Setting” is not displayed while “REMOTE” is selected from “External Control” in the

INSTALL SETTING menu.

22

The SET SETTING Menu

The MENU SETTING Menu

The MENU SETTING menu is used for setting for the operations by using the menu or the
Remote Commander.

Items Item descriptions

Status On: All on-screen statuses are enabled.

Off: Turn off the on-screen displays except for the menus, message when

turning off the power, and warning messages.

Language Selects the language used in the menu and on-screen displays.

Menu Position Top Left/Bottom Left/Center/Top Right/Bottom Right: Selects the display

position of the menu.

Start Up Image On/Off: When set to “On,” the Start Up Image is displayed on the screen upon

startup of the projector.

Adjustments and Settings Using a Menu

The MENU SETTING Menu

23

The INSTALL SETTING Menu

The INSTALL SETTING menu is used for installing the projector.

Items Item descriptions

V Keystone

Image Flip HV/H/V/Off: Flips the projected image horizontally and/or vertically

Background Black/Blue: Selects the background color of the projected image when no

Lamp Mode High/Standard/Low: When set to “High,” the image becomes brighter,

High Altitude
Mode

Security Lock

Direct Power On On/Off: When set to “On,” you can turn the power on without going to

External Control REMOTE: Select to control the projector using RS-232C.

Standby Mode

*1

*2

Auto: Set keystone adjustment automatically. When the projector is
installed on an uneven surface, the feature may not work properly. In this
case, select “Manual” to set keystone adjustment manually.
Manual: The higher the setting, narrower the top of the projected image.
The lower the setting, narrower the bottom of the projected image.

according to the installation method.

signal is input.

and power consumption becomes higher.

On/Off: Set to “On” when using the projector at an altitude of 1,500 m or
higher. Continuing to use the wrong setting may affect component
reliability.

*3

On/Off: This function enables restriction of the projector to authorized
users by password. The setting procedures for security locking are as
follows:

1 Select “On” and press ENTER to display the setting menu.
2 Input the password with the MENU, V/v/B/b, and ENTER keys. (The

default password setting is “ENTER, ENTER, ENTER, ENTER.”)

3 Input a new password with the MENU, V/v/B/b, and ENTER keys.
4 Enter the password again to confirm.

Enter the password when you turn on the projector after disconnecting and
reconnecting the AC power cord.
When it is set to “Off,” you can cancel the security lock. You are required to
input the password again.
If you fail to enter the correct password after three consecutive times, the
projector cannot be used. In this case, press the ?/1 key to go Standby
mode then turn on the power again.

Standby mode when the AC power cord is connected to a wall outlet.
Regardless of the Direct Power On setting, you can disconnect the AC
power cord to turn off the power without going to the Standby mode.

NETWORK: Select to control the projector via network.

*4

Standard/Low: When set to “Low,” lowers power consumption in Standby
mode.

Notes

*1: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.
*2: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise

becomes slightly louder.

*3: You will not be able to use the projector if you forget your password. If you call qualified Sony

personnel because you have forgotten the password, you will be asked to verify the projector’s

24

The INSTALL SETTING Menu

serial number and your identity. (This process may differ in other countries/regions.) Once your
identity has been confirmed, we will provide you with the password.

*4: When “Standby Mode” is set to “Low,” the network and network control function cannot be

operated while the projector is in standby mode.

Adjustments and Settings Using a Menu

The INSTALL SETTING Menu

25

The INFORMATION Menu

The INFORMATION menu enables you to confirm various information on the projector, such
as the total usage hours of a lamp.

Items Item descriptions

Model Name Displays the model name.

Serial No. Displays the serial number.

*1

fH

*1

fV

Signal type Displays the type of the current input signal.

Lamp Timer Indicates the total usage time of a lamp.

Note

*1: These items may not be displayed depending on the input signal.

Displays the horizontal frequency of the current input signal.

Displays the vertical frequency of the current input signal.

26

The INFORMATION Menu

B Network

Using Network Features

Connection to the network allows you to operate the following features:

• Checking the current status of the projector via a Web browser.

• Remotely controlling the projector via a Web browser.

• Receiving the e-mail report for the projector.

• Making the network settings for the projector.

• Supports network monitoring, control protocol (Advertisement, PJ Talk, PJ Link, AMX
DDDP [Dynamic Device Discovery Protocol]).

Notes

• The menu displays used for the explanation below may be different depending on the model you
are using.

• Supported Web browsers are Internet Explorer 6/7/8.

• The menu displays only English.

• If the browser of your computer is set to [Use a proxy server] when you have access to the projector
from your computer, click the check mark to set accessing without using a proxy server.

Displaying the Control Window of the Projector with a Web Browser

1 Connect the LAN cable.

LAN cable
(straight type)
(not supplied)

Hub, router, etc

LAN Connector

2 Set the network settings for the

projector using “Network Setting” on
the SET SETTING menu (page 21).

3 Start a web browser on the computer,

enter the following in the address field,
then press the Enter key on your
computer.

http://xxx.xxx.xxx.xxx
(xxx.xxx.xxx.xxx: IP address for the
projector)

You can confirm the IP address of the
projector under “Network Setting” on
the SET SETTING menu.

The following window appears in the
Web browser:

Once you make the network settings, you
can open the Control window only by
performing step 3 of this procedure.

How to operate the Control window

Switching the page

Click one of the Page Switching buttons to
display the desired setting page.

Page Switching buttons

Network

Using Network Features

27

Confirming the Information regarding the Projector

You can confirm the current settings for the
projector on the Information page.

Information area

Operating the Projector from a Computer

You can control the projector from the
computer on the Control page.

No password is set by default. The user
name is preset to “root.” Input required
information after logging in.

Changing the password

Enable: Select to set a new password.
Disable: Select not to change the

password.

Note

If you forget your password, consult with
qualified Sony personnel.

Operation area

The functions of the keys shown in the
operation area are the same as those of the
keys on the supplied Remote Commander.

Making the Network Settings

Setting the network password

The log-in screen appears after the Network
page is selected.

28

Using Network Features

Setting the location

Location: Input information on where

the projector is installed.

Using the e-mail report Function

Set the e-mail report function on the Mail
Report page. Entered values will not be
applied unless you click on [Apply].

1 Set the e-mail report function.

Enable: Select to activate the e-mail

report function.

Disable: Select to deactivate the e-mail

report function.

1

2
3

4

5

2 Enter the outgoing e-mail address in

the Send To box then check the Report
Timing check box of the e-mail report
to be sent.

A massage will be sent simultaneously
to secondary recipients by entering their
e-mail addresses in the CC box.

3 Set the timing to send e-mail report.

Over Lamp Usage Time: Tick the box

to send a report that indicates the time
for lamp replacement.

Error: Tick the box to send a report that

indicates an error occurring.

4 Set the mail account for sending e-

mail reports.

User Name: Enter the allocated user

name. Up to 64 characters can be
input.

Password: Enter the e-mail password.
SMTP Server: Enter the address of

outgoing mail server (SMTP). Up to
64 characters can be input.

Network

5 Send the test mail.

Check on the Send test mail check box
then click on [Apply] to send your test
mail to the e-mail address you set.

Notes

• The e-mail report function is not available
because the network which Outbound Port25
Blocking is used cannot be connected to the
SMTP server.

• You cannot use the following characters to
enter the characters in the text box: “ ' ”, “ “
”, “ & ”, “ < ”, “ > ”

Using Network Features

29

B Others

Indicators

The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table
below.

?/1 key

Status Meaning/Remedies

Lights in red The projector is in Standby mode.

Flashes in green • The projector is ready to operate after having been turned on.

Lights in green The projector’s power is on.

Lights in orange The projector is in Power Saving Mode (lamp cut off). (page 21)

Flashes in red The projector is in abnormal status. Symptoms are indicated by

Flashes twice The internal temperature is unusually high. Check the items below.

Flashes six times Unplug the AC power cord from a wall outlet. After checking that the

Other number of
flashes

• The lamp cools after the projector is turned off.

number of flashes. Address the problem in accordance with the
following. If the symptom is shown again, consult with qualified Sony
personnel.

• Check to see if nothing is blocking the ventilation holes.

• Check to see if the air filter is not clogged. (page 3, page 36)

?/1 key goes out, plug the power cord to a wall outlet again then turn
on the projector.

Consult with qualified Sony personnel.

LAMP/COVER indicator

Status Meaning/Remedies

Flashes in red Symptoms are indicated by number of flashes. Address the problem in

Flashes twice The lamp cover or the air filter cover is not attached securely.

Flashes three times The temperature of lamp is unusually high. Turn off the power and

30

Indicators

accordance with the following.

(page 36)

wait for lamp to cool then turn on the power again. If the symptom is
shown again, the lamp may be burnt out. In such a case, replace the
lamp with a new one (page 34).

Messages List

When any of the messages listed below appears on the projected image, address the problem in
accordance with the table below.

Message Meaning/Remedy Page

High temp.! Lamp off in
1 min.

Frequency is out of
range!

Please check Input-A
Signal Sel.

Please replace the Lamp
and clean the Filter.

Not applicable! Invalid key pressed. –

The panel keys are
locked!

Check the items below.

• Check to see if nothing is blocking the ventilation holes.

• Check to see if the air filter is not clogged.

Change the output setting of the connected equipment to one
for signals supported by the projector.

Set “Input-A Signal Sel.” to “Auto” or select the input signal
type to suit to the input signal.

Replace the lamp with a new one and clean the air filter. The
message appears whenever you turn on the power until you
replace the lamp and reset the lamp timer.

“Panel Key Lock” is set to “On.” 21

3, 36

41

21

34, 36

Messages List

Others

31

Troubleshooting

Before asking to have the projector repaired, try to diagnose the problem, following the
instructions below.

Symptom Remedy Page

The power is not turned
on.

No image. Check if the connecting cable is connected to external

On-screen display does
not appear.

The aspect ratio of the
display is not right/the
image is displayed
smaller /a portion of
image does not appear.

The image is a
trapezoid.

The image is dark/too
bright.

Check if the AC power cord is firmly connected. –

When the “Panel Key Lock” is set to “On,” you cannot turn on
the projector using the ?/1 key on the projector.

If the lamp or lamp cover is not attached securely, the projector
cannot be turned on.

If the air filter or air filter cover is not attached securely, the
projector cannot be turned on.

equipment firmly.

Check if the computer signal is set for output to an external
monitor. If you set your computer, such as a notebook
computer, to output the signal to both your computer’s display
and an external monitor, the picture of the external monitor
may not appear properly. Set your computer to output the
signal to only an external monitor.

Check if the input source is correctly selected. 11

Check if the picture is muted. 6

The on-screen display does not appear when “Status” in the
MENU SETTING menu is set to “Off.”

Set “Aspect” manually. 5, 17,

The images become trapezoidal because of the projection
angle. In such a case, you can correct the trapezoidal
distortion, using a Keystone feature.

When the “V Keystone” is set to “Manual,” the keystone
feature does not work automatically. Set “V Keystone” to
“Auto” or “Manual” to set manually.

When the projector is installed on an uneven surface, the
feature may not work properly. In this case, select “Manual” to
set “V Keystone” manually.

The settings for “Brightness,” “Contrast,” and “Lamp Mode”
affect brightness of the image. Check if the value is
appropriate.

The image will be dark when the lamp is burnt out. Check
“Lamp Timer,” and replace the lamp with a new one if
necessary.

19

5, 13,
24

5, 13,
24

5, 13,
24

16, 24

21

34

36

–

11

23

26

32

Troubleshooting

Symptom Remedy Page

The image is not clear. Check if the projector is in focus. 12

The picture will not be clear if condensation has accumulated
on the lens. In such a case, let the projector sit for about two
hours with the power on.

The image is noisy. Check if the connecting cable is connected to external

No sound. Check that the connecting cables between the projector and

The Remote
Commander does not
work.

The fan is noisy. The sound from the fan is often greater than normal to cool the

equipment properly.

external video or audio equipment are securely connected.

Check if the output setting of connected external audio
equipment is set to output the audio signal from the projector.

Check if the connecting cable is connected to external
equipment firmly.

Audio is not output if audio muting is activated. 6

Check if “Volume” is not set to minimum. 6, 16

Check that the batteries are installed correctly. –

Check that the batteries are not exhausted. –

lamp, etc. in the following cases.

• “Lamp Mode” is set to “High.”

• “High Altitude Mode” is set to “On.”

• The unit is used in the location where the temperature is high.

If the ventilation holes are blocked, the internal temperature of
the projector rises and the fan noise becomes larger.

–

7

7

–

–

24

3

Troubleshooting

Others

33

Replacing the Lamp

Replace the lamp with a new one if a message displayed on the projected image or the LAMP/
COVER indicator notifies you to replace the lamp (pages 30, 31).
Use an LMP-E211 projector lamp (not supplied) for replacement.

Caution

• The lamp remains hot after the projector is

turned off. If you touch the lamp, you may

burn your finger. When you replace the
lamp, wait for at least an hour after
turning off the projector for the lamp to
cool sufficiently.

• Do not allow any metallic or inflammable
objects into the lamp replacement slot after
removing the lamp, otherwise it may cause
electrical shock or fire. Do not put your
hands into the slot.

• If the lamp breaks, contact qualified

Sony personnel. Do not replace the lamp
yourself.

• When removing the lamp, be sure to pull it
out straight, by holding the designated
location. If you touch a part of the lamp other
than the designated location, you may be
burned or injured. If you pull out the lamp
while the projector is tilted, the pieces may
scatter if the lamp breaks any may cause
injury.

1 Turn off the projector, and disconnect

the AC power cord from a wall outlet.

2 When the lamp has cooled

sufficiently, open the lamp cover by
loosening 1 screw.

3 Loosen the 2 screws on the lamp then

pull out the lamp by its grab.

Grab

34

Replacing the Lamp

4 Insert the new lamp all the way in until

it is securely in place. Tighten the
2 screws.

5 Close the lamp cover and tighten the

1 screw.

Note

Be sure to install the lamp and Lamp cover
securely as it was. If not, the projector
cannot be turned on.

Caution

Disposal of the used lamp

For the customers in the USA

Lamp in this product contains mercury.
Disposal of these materials may be
regulated due to environmental
considerations. For disposal or
recycling information, please contact
your local authorities or the
Telecommunications Industry
Association (www.eiae.org).

6 Connect the AC power cord to a wall

outlet and turn on the projector.

7 Reset the lamp timer for notification of

the next replacement time.
Select “Lamp Timer Reset” on the SET

SETTING menu then press the ENTER
key. When a message appears, select
“Yes” to reset the lamp timer (page 21).

Replacing the Lamp

Others

35

Cleaning the Air Filter

When a message appears on the projected image, clean the air filter (page 31).
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with
a new one.
For details on a new air filter, consult with qualified Sony personnel.

Caution

If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the
temperature may rise inside the unit, leading to a possible malfunction or fire.

1 Turn off the projector, and disconnect

the AC power cord from the AC outlet.

2 Draw out the air filter cover.

Air filter

3 Clean the air filter with a vacuum

cleaner.

Remove the air filter as illustrated below
then clean with the vacuum cleaner.

Claws

4 Attach the air filter cover to the unit.

Note

Be sure to attach the air filter cover firmly. If
not, the projector cannot be turned on.

36

Cleaning the Air Filter

Specifications

Item Description

Model VPL-SX125/VPL-SW125

Projection system 3 LCD system

Display device Effective display

Projection lens Focus Manual

Light source High-pressure mercury lamp, 210 W type

Projected image
size

Luminous flux
(Brightness)

Speaker 1 W × 1 (monaural)

Applicable
scanning
frequency

Resolution When a computer

Color system NTSC

*1

size

Effective picture
elements

signal is input

When a video
signal is input

VPL-SX125: 0.63 inch (16.0 mm), 3 plate, Aspect ratio
4:3
VPL-SW125: 0.59-inch (15.0 mm), 3 plate, Aspect ratio
16:10

VPL-SX125: 2,359,296 pixels (1024 × 768 pixels, 3
plate panels)
VPL-SW125: 3,072,000 pixels (1280 × 800 pixels, 3
plate panels)

VPL-SX125: 50 inches to 110 inches (1.27 m to 2.79 m)
VPL-SW125: 50 inches to 100 inches (1.27 m to 2.54 m)

VPL-SX125: 2500 lm
VPL-SW125: 2600 lm
(when “Lamp Mode” is set to “High”)

Horizontal: 19 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz

Maximum display resolution: 1400 × 1050 pixels (resize)
Panel display resolution:
VPL-SX125: 1024 × 768 pixels
VPL-SW125: 1280 × 800 pixels

NTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p,
576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i

3.58, PAL, SECAM, NTSC4.43, PA L - M , PAL-N,

PA L6 0

Others

Specifications

37

Item Description

Model VPL-SX125/VPL-SW125

INPUT OUTPUT
(Computer/video)

INPUT A RGB/YPBPR input connector: Mini D-sub 15 pin

female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75
ohms terminated, RGB/P

BPR: 0.7 Vp-p ± 2 dB, 75 ohms

terminated, Sync signal: TTL level high impedance,
positive/negative
Audio input connector: Stereo mini jack, rated input
500 mVrms, input impedance more than 47 kohms

INPUT B
(VPL-SX125
only)

RGB input connector: Mini D-sub 15-pin female,
RGB: 0.7 Vp-p ± 2 dB, 75 ohms terminated, Sync signal:
TTL level high impedance, positive/negative
Audio input connector: Stereo mini jack, rated input
500 mVrms, input impedance more than 47 kohms

INPUT B
(VPL-SW125

HDMI input connector: HDMI 19-pin, HDCP support,
HDMI audio support

only)

S VIDEO (S
VIDEO IN)

S video input connector: Mini DIN 4-pin, Y: 1 Vp-p ± 2
dB, sync negative, 75 ohmes terminated, C: (burst signal)

0.286 (NTSC)/0.3 (PAL/SECAM) Vp-p ± 2 dB, 75 ohms
terminated
Audio input connector: Phono jack × 2, rated input
500 mVrms, Input impedance more than 47 kohms

VIDEO (VIDEO
IN)

Video input connector: Phono jack, 1 Vp-p ± 2 dB,
sync negative, 75 ohmes terminated
Audio input connector: Shared with S VIDEO IN

OUTPUT MONITOR output connector: Mini D-sub 15-pin

female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75
ohms terminated, RGB/P

BPR: 0.7 Vp-p ± 2 dB, 75 ohms

terminated, Sync signal: HD, VD 4 V (open), 1 Vp-p (75
ohms), positive/negative
Audio output connector: Stereo mini jack, stereo, 1
Vrms (maximum volume, when inputting 500 mVrms),
output impedance 5 kohms

Others connector RS-232C connector: D-Sub 9 pin female

LAN connector: RJ45, 10BASE-T/100BASE-TX

Operating
temperature/

0 °C to 40 °C (32 °F to 104 °F)/20% to 80% (no

condensation)
Operating
humidity

Storage
temperature/

–10 °C to +60 °C (14 °F to 140 °F)/ 20% to 80% (no

condensation)
Storage humidity

Power

100 V to 240 V AC, 3.0 A-1.3 A, 50/60 Hz
requirements

Power
consumption

100 V AC: 290 W

240 V AC: 275 W

Standby power 100 V AC: 3 W (when “Standby Mode” is set to

“Standard”)/1 W (when “Standby Mode” is set to “Low”)

240 V AC: 3 W (when “Standby Mode” is set to

“Standard”)/1 W (when “Standby Mode” is set to “Low”)

38

Specifications

Item Description

Model VPL-SX125/VPL-SW125

Heat dissipation 100 V AC: 990 BTU

240 V AC: 940 BTU

Standard
dimensions
(W/H/D)

Approx. 313.4 × 160.3 × 349.3 mm (12

3

13

/4)

Approx. 313.4 × 144.9 × 349.3 mm (1211/32 × 523/32 ×

3

13

/4 inches) (without projecting parts)

11

/32 × 65/16 ×

Mass Approx. 3.7 kg (8 lb 3 oz)

Supplied
accessories

Optional
accessories

Notes

*2 *3

See “Checking the Supplied Accessories” in the supplied
Quick Reference Manual.

Projector Lamp LMP-E211 (for replacement)

*1: For details, refer to “Acceptable Input Signals” on page 41.
*2: Information on accessories in this manual is current as of April 2011.
*3: Not all optional accessories are available in all countries and area. Please check with your local

Sony Authorized Dealer.

Design and specifications of the unit, including the optional accessories, are subject to change
without notice.

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE
FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING
THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.

Specifications

Others

39

Pin assignment

RGB input connector (Mini D-sub
15-pin, female)

1 Video input

(red) R

2 Video input

9Power supply

input for DDC

10 GND

(green) G

3 Video input

11 GND

(blue) B

4 GND 12 DDC/SDA

5 RESERVE 13 Horizontal sync

signal

6 GND (R) 14 Vertical sync

signal

7 GND (G) 15 DDC/SCL

8 GND (B)

RS-232C connector (D-Sub 9-pin,
female)

51

9

6

1NC 6NC

2RXDA 7RTS

3TXDA 8CTS

4DTR 9NC

5GND

40

Specifications

Acceptable Input Signals

Computer signal

Resolution

fH [kHz]/

fV [Hz]

Input connector

RGB HDMI

640 × 350 31.5/70

37.9/85

640 × 400 24.8/56

31.5/70

37.9/85

640 × 480 31.5/60

35.0/67

37.9/73

37.5/75

43.3/85

800 × 600 35.2/56

37.9/60

48.1/72

46.9/75

53.7/85

832 × 624 49.7/75

1024 × 768 48.4/60

56.5/70

60.0/75

68.7/85

1152 × 864 64.0/70

67.5/75

77.5/85

1152 × 900 61.8/66

1280 × 960 60.0/60

75.0/75

1280 × 1024 64.0/60

80.0/75

91.1/85

1400 × 1050 65.3/60

1280 × 768 47.8/60

1280 × 720 45.0/60

1360 × 768 47.7/60

*1

z

z

z

z

z

zz

z

z

z

z

z

zz

z

z

z

z

zz

z

z

z

z

z

z

z

zz

z

zz

z

z

zz

zz

zz

zz

Resolution

fH [kHz]/

fV [Hz]

1440 × 900 55.9/60

1280 × 800 49.7/60

Input connector

RGB HDMI

zz

zz

*1

Digital TV signal

Input connector

Signal fV [Hz]

480i 60

576i 50

480p 60

576p 50

1080i 60

1080i 50

720p 60

720p 50

RGB/

YP

BPR

zz

zz

zz

zz

zz

zz

zz

zz

HDMI

*1

Analog TV signal

Input

Signal fV [Hz]

connector

VIDEO /

S VIDEO

NTSC 60

PA L/ S EC A M 5 0

z

z

Notes

*1: Available for VPL-SW125 only.

• When a signal other than the signals listed in
table is input, the picture may not be
displayed properly.

• An input signal meant for screen resolution
different from that of the panel will not be
displayed in its original resolution. Text and
lines may be uneven.

Others

Specifications

41

Projection Distance

The following describes the projection distance and height from lens center to bottom of screen
by each projected screen size.
The projection distance is the distance between the front of the lens and the surface of the
projected image.
Height H is the height from the bottom of the projected image (top for ceiling mount) to A
(determined by drawing a perpendicular line from lens center to projected image surface).

Floor Installation (Adjuster (rear) fully extended)

Projection distance L

Height H from lens
center to bottom
of screen

Projected
image

A

Front of the lens

VPL-SX125

Projection distance

Unit: m (inches)

Projected image size

Diagonal D Width × Height

50 inch (1.27 m) 1.02 × 0.76 (40 × 30) 0.61 (24) 0.08 (3.00)

80 inch (2.03 m) 1.63 × 1.22 (64 × 48) 1.00 (39) 0.12 (4.80)

90 inch (2.29 m) 1.83 × 1.37 (72 × 54) 1.13 (44) 0.14 (5.40)

100 inch (2.54 m) 2.03 × 1.52 (80 × 60) 1.26 (50) 0.15 (6.00)

110 inch (2.79 m) 2.24 × 1.68 (88 × 66) 1.39 (55) 0.17 (6.60)

Projection

Distance L

Height H from lens
center to bottom of

Projection distance formula

D: Projected image size (Diagonal)
H: Distance between the bottom edge of the image and the center of the lens

screen

42

Projection Distance

Expression#1 Unit: m (inches)

Projection Distance L

L=0.013009 × D – 0.0384 (L=0.512178 × D – 1.5125)

Expression#2

Height H from lens center to bottom of screen

H=0.00152 × D (H=0.06000 × D)

VPL-SW125

Projection distance

Unit: m (inches)

Projected image size

Diagonal D Width × Height

50 inch (1.27 m) 1.08 × 0.67 (42 × 26) 0.65 (26) 0.15 (5.83)

60 inch (1.52 m) 1.29 × 0.81 (51 × 32) 0.79 (31) 0.18 (7.00)

70 inch (1.78 m) 1.51 × 0.94 (59 × 37) 0.93 (36) 0.21 (8.16)

80 inch (2.03 m) 1.72 × 1.08 (68 × 42) 1.06 (42) 0.24 (9.33)

100 inch (2.54 m) 2.15 × 1.35 (85 × 53) 1.34 (53) 0.30 (11.66)

Projection
Distance L

Height H from lens
center to bottom of

screen

Projection distance formula

D: Projected image size (Diagonal)
H: Distance between the bottom edge of the image and the center of the lens

Expression#1 Unit: m (inches)

Projection Distance L

L=0.013794 × D – 0.0394 (L=0.543087 × D – 1.5503)

Expression#2

Height H from lens center to bottom of screen

H=0.00296 × D (H=0.11660 × D)

Projection Distance

Others

43

Ceiling Installation (Top side parallel to ceiling)

Caution

Never mount the projector on the ceiling or move it by yourself. Be sure to consult with
qualified Sony personnel (charged).

Height H from
lens center to
top of screen

Front of the lens

A

Projected
image

Projection distance L

Top side

VPL-SX125

Projection distance

Unit: m (inches)

Projected image size

Diagonal D Width × Height

50 inch (1.27 m) 1.02 × 0.76 (40 × 30) 0.61 (24) 0.08 (3.00)

80 inch (2.03 m) 1.63 × 1.22 (64 × 48) 1.00 (39) 0.12 (4.80)

90 inch (2.29 m) 1.83 × 1.37 (72 × 54) 1.13 (44) 0.14 (5.40)

100 inch (2.54 m) 2.03 × 1.52 (80 × 60) 1.26 (50) 0.15 (6.00)

110 inch (2.79 m) 2.24 × 1.68 (88 × 66) 1.39 (55) 0.17 (6.60)

Projection

Distance L

Height H from lens

center to top of screen

Projection distance formula

D: Projected image size (Diagonal)
H: Distance between the top edge of the image and the center of the lens

Expression#1 Unit: m (inches)

Projection Distance L

L=0.013009 × D – 0.0384 (L=0.512178 × D – 1.5125)

44

Projection Distance

Expression#2

Height H from lens center to top of screen

H=0.00152 × D (H=0.06000 × D)

In the case of ceiling mounting, check with your dealer regarding the use of a mount kit that is
warranted for use with this product.

VPL-SW125

Projection distance

Unit: m (inches)

Projected image size

Diagonal D Width × Height

50 inch (1.27 m) 1.08 × 0.67 (42 × 26) 0.65 (26) 0.15 (5.83)

60 inch (1.52 m) 1.29 × 0.81 (51 × 32) 0.79 (31) 0.18 (7.00)

70 inch (1.78 m) 1.51 × 0.94 (59 × 37) 0.93 (36) 0.21 (8.16)

80 inch (2.03 m) 1.72 × 1.08 (68 × 42) 1.06 (42) 0.24 (9.33)

100 inch (2.54 m) 2.15 × 1.35 (85 × 53) 1.34 (53) 0.30 (11.66)

Projection
Distance L

Height H from lens

center to top of screen

Projection distance formula

D: Projected image size (Diagonal)
H: Distance between the top edge of the image and the center of the lens

Expression#1 Unit: m (inches)

Projection Distance L

L=0.013794 × D – 0.0394 (L=0.543087 × D – 1.5503)

Expression#2

Height H from lens center to top of screen

H=0.00296 × D (H=0.11660 × D)

In the case of ceiling mounting, check with your dealer regarding the use of a mount kit that is
warranted for use with this product.

Others

Projection Distance

45

Dimensions

Front

Side

144.9

23

(5

/32)

114.1
(4 1/2)

313.4 (12

349.3 (13 3/4)

11

/32)

269 (10

79.7 (3 1/8)

19

/32)

Unit: mm (inches)

46

Unit: mm (inches)

Dimensions

Side (Top side parallel to ceiling)

69.4

23

(2

/32)

Center of
the lens

5

/32)

79.9 (3

Bottom

27.3 (1

34

11

/32)

(1

Center of
the lens

188

13

/32)

(7

131.8

3

/16)

(5

Unit: mm (inches)

24.4 (

31

/32)

1

/16)

40.2
(1 19/32)

1

77 (3

/32)

40.2

19

/32)

(1

5

/16)

8.2 (

Others

31

24.4 (

/32)

18.1 (23/32)

29

22.7 (

/32)

249 (9

1

/8)

79.3 (3

15

125.4 (4

13

/16)

/16)

Unit: mm (inches)

Dimensions

47

Index

A

AC IN ........................................................4

Acceptable input signal ...........................41

Adjust Signal ........................................... 17

Adjuster ...............................................3, 12

Air filter ................................................... 36

Air filter cover/Ventilation holes

(intake) ...............................................3

APA ........................................................... 5

Aspect ...........................................5, 17, 19

Audio muting ............................................ 6

Auto Input Search ................................... 21

B

Background .............................................24

Brightness ...............................................16

C

CC Display .............................................. 21

Color .......................................................16

Color System ...........................................21

Color Temp. ............................................ 16

Connecting a computer ............................. 7

Connecting a Video equipment .................8

Connecting an external monitor and audio

equipment ........................................10

Connector panel .................................... 3, 4

Contrast ...................................................16

Control panel ............................................. 5

D

DDE ........................................................16

Default Gateway ...................................... 21

Digital Zoom ............................................. 5

Direct Power On ......................................24

DNS Server .............................................21

Dot Phase ................................................ 17

E

ECO MODE (Energy-saving mode) .........6

e-mail report ............................................ 28

External Control ...................................... 24

F

fH ............................................................26

Focus .......................................................12

Focus ring ..................................................3

Freeze ........................................................6

fV .............................................................26

G

Gamma Mode ..........................................16

H

H Size ......................................................17

High Altitude Mode .................................24

Hue ..........................................................16

I

Image Flip ................................................24

Information menu ....................................26

Input ...........................................................4

INPUT SETTING menu ..........................17

Input-A Signal Sel. ..................................21

INSTALL SETTING menu .....................24

IP Address ...............................................21

IP Address Setup .....................................21

K

Keystone ....................................................5

L

Lamp cover ................................................3

Lamp Mode .............................................24

Lamp Timer .............................................26

Lamp Timer Reset ...................................21

LAMP/COVER indicator ....................3, 30

LAN connector ..........................................4

Language .................................................23

Location and function of controls ..............3

M

Main unit ...................................................3

MENU SETTING menu ..........................23

Messages list ............................................31

Model Name ............................................26

N

Network Features .....................................27

Network Setting .......................................21

O

Output ........................................................4

Over Scan ................................................17

48

Index

P

Panel Key Lock ....................................... 21

Picture mode ............................................16

Picture muting ........................................... 6

PICTURE SETTING menu .....................16

Pin assignment .........................................40

Power Saving Mode ................................21

Projecting an image .................................11

Projection distance ..................................42

R

Remote commander ...................................5

Remote control detector ............................3

Replacing the lamp ..................................34

RS-232C ....................................................4

S

Security bar ...............................................3

Security Lock ...................................... 3, 24

Selecting an input signal ...........................5

Serial No. .................................................26

SET SETTING menu ..............................21

Sharpness .................................................16

Shift .........................................................17

Smart APA ...............................................21

Specifications ..........................................37

Standby Mode .........................................24

Start Up Image ........................................23

Status .......................................................23

Subnet Mask ............................................21

About Trademarks

• Adobe and Adobe Acrobat are trademarks
or registered trademarks of Adobe
Systems Incorporated in the United States
and/or other countries.

• Kensington is a registered trademark of
Kensington Technology Group.

• HDMI, HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC.

• Internet Explore is registered trademarks
of Microsoft Corporation in the United
States and/or other countries.

• PJLink is a registered trademark of Japan
Business Machine and Information
System Industries Association.

• AMX is a trademark of AMX Corporation.

• All other trademarks and registered
trademarks are trademarks or registered
trademarks of their respective holders. In
this manual,
specified.

™

and ® marks are not

T

Troubleshooting .......................................32

Turn off ................................................5, 14

Turn on ................................................5, 11

U

Using a menu ...........................................15

V

V Keystone ....................................5, 13, 24

Ventilation holes ........................................ 3

Volume ......................................................6

Z

Zoom .......................................................12

Index

Others

49

Sony Corporation