Sony VPL-PS10 User Manual [en, es, fr]

VPL-PX15/PX10/PS10

4-083-534-15(1)

LCD Data Pr ojector

Operating Instructions Mode d’emploi Manual de instrucciones

GB FR ES

VPL-PX15 VPL-PX10 VPL-PS10

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For the customers of the VPL-PX15/PX10

LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT

RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU APPAREIL A LASER DE CLASSE 2 LASER–STRAHLING, NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 MAX OUTPUT : 1mW EN60825-1 WAVE LENGTH : 645nm /A11:1996

This label is located on the rear of the Remote Commander.

CAUTION

LASER RADIATION DO NOT STARE INTO BEAM

WAVE LENGTH:645nm MAX OUTPUT:1mW

CLASS II LASER PRODUCT

COMPLIES WITH DHHS 21 CFR SUBCHAPTER J

SONY CORPORATION 6-7-35 KITASHINAGAWA SHINAGAW A-KU, TOKY O, JAP AN

MANUFACTURED

AVOID EXPOSURELASER RADIATION IS EMITTED FROM THIS APERTURE.

Laser light shines out of this window.

This label is located on the rear of the Remote Commander.

For the customers in the USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Caution

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Notes

• Do not aim the laser at people and do not look into the laser transmitter.

• If the Remote Commander malfunctions or causes a malfunction, consult with qualified Sony personnel. We will exchange the Remote Commander for a new one based on the terms of the guarantee.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

2 (GB)

For the customers in the United Kingdom

Voor de klanten in Nederland

WARNING THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green-and-Yellow: Earth Blue: Neutral

Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

• Dit apparaat bevat een vast ingebouwde batterij die niet vervangen hoeft te worden tijdens de levensduur van het apparaat.

• Raadpleeg uw leverancier indien de batterij toch vervangen moet worden. De batterij mag alleen vervangen worden door vakbekwaam servicepersoneel.

• Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).

• Lever het apparaat aan het einde van de levensduur in voor recycling, de batterij zal dan op correcte wijze verwerkt worden.

The socket-outlet should be installed near the equipment and be easily accessible.

Apparaten ma kun tilkoples jordet stikkontakt. Apparatet må kun tilkoples jordet stikkontakt.

English

Warning on power connection

Use a proper power cord for your local power supply.

The United States, Continental UK, Ireland, Japan Canada Europe Australia, New Zealand

Plug type VM0233 290B YP-12A COX-07 — Female end VM0089 386A YC-13B COX-02 VM0310B YC-13 Cord type SJT SJT H05VV-F H05VV-F N13237/CO-228 VCTF Rated Voltage & Current 10A/125V 10A/125V 10A/250V 10A/250V 10A/250V 7A/125V Safety approval UL/CSA UL/CSA VDE VDE VDE DENAN

YP332

.........................................................................................................................................................................................................

1) Use the correct plug for your country.

3 (GB)

4 (GB)

Table of Contents

Overview

Setting Up and Projecting

Precautions ............................................................... 7 (GB)

Features..................................................................... 8 (GB)

Location and Function of Controls......................... 9 (GB)

Front / Left Side ....................................................... 9 (GB)

Rear / Right Side / Bottom....................................... 9 (GB)

Control Panel ......................................................... 11 (GB)

Connector Panel ..................................................... 13 (GB)

Remote Commander (supplied with the

VPL-PX15/PX10)............................................. 14 (GB)

Remote Commander (supplied with the

VPL-PS10)........................................................ 16 (GB)

Installing the Projector........................................... 18 (GB)

Connecting the Projector....................................... 18 (GB)

Connecting to a Computer ..................................... 18 (GB)

Connecting to a VCR or 15k RGB/Component

Equipment......................................................... 20 (GB)

Connecting to a LAN (VPL-PX15 only) ............... 21 (GB)

Selecting the Menu Language............................... 23 (GB)

Projecting ................................................................ 24 (GB)

Adjustments and Settings Using the Menu

Using the Menu....................................................... 27 (GB)

The PICTURE CTRL Menu ..................................... 28 (GB)

The INPUT SETTING Menu .................................... 29 (GB)

The SET SETTING Menu ........................................ 31 (GB)

The INSTALL SETTING Menu ................................ 32 (GB)

Installation

Installation Example............................................... 34 (GB)

Notes for Installation.............................................. 35 (GB)

Unsuitable Installation ........................................... 35 (GB)

Unsuitable Conditions for Use............................... 35 (GB)

5 (GB)

Maintenance

Other

Maintenance............................................................ 37 (GB)

Replacing the Lamp ............................................... 37 (GB)

Cleaning the Air Filter ........................................... 38 (GB)

Troubleshooting ..................................................... 39 (GB)

Specifications ......................................................... 41 (GB)

Index ........................................................................ 44 (GB)

6 (GB)

Precautions

On safety

•Check that the operating voltage of your unit is identical with the voltage of your local power supply.

•Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further.

•Unplug the unit from the wall outlet if it is not to be used for several days.

•To disconnect the cord, pull it out by the plug. Never pull the cord itself.

•The wall outlet should be near the unit and easily accessible.

•The unit is not disconnected to the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

•Do not look into the lens while the lamp is on.

•Do not aim the laser at people and do not look into the laser transmitter.

•Do not place your hand or objects near the ventilation holes — the air coming out is hot.

•Be careful not to catch your fingers with the adjusters when you lift up the projector. Do not push hard on the top of the projector with the adjusters out.

•Be sure to grasp both sides when carrying the projector.

On illumination

On preventing internal heat build-up

After you turn off the power with the I / 1 key on the Remote Commander or on the control panel, do not disconnect the unit from the wall outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation holes (intake) on the bottom and ventilation holes (exhaust) on the front. Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

On cleaning

•To keep the cabinet looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents, such as thinner, benzene, or abrasive cleansers, since these will damage the cabinet.

•Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

•Clean the filter at regular intervals, every 300 hours.

On repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory.

Overview

•To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight.

•Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio.

•Cover any windows that face the screen with opaque draperies.

•It is desirable to install the projector in a room where floor and walls are not of light-reflecting material. If the floor and walls are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color.

About the LCD projector

The LCD projector is manufactured using highprecision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the LCD projector. This is a normal result of the manufacturing process and does not indicate a malfunction.

7 (GB)

Features

High brightness, high picture quality

•High brightness

Adopting a newly developed optical system and a 200 W UHP lamp allows high brightness (VPL-PX15/ PX10: light output 2000 ANSI lumen, VPL-PS10: light output 1500 ANSI lumen) and excellent uniformity on the picture.

•High resolution

VPL-PX15/PX10

Three 0.9-inch, approximately 790,000 pixel, XGA panels provide a resolution of 1024 × 768 dots for RGB input and 750 horizontal TV lines for video input.

VPL-PS10

Three 0.9-inch, approximately 480,000 pixel, SVGA panels provide a resolution of 800 × 600 dots for RGB input and 600 horizontal TV lines for video input.

Simple setup

•Simple setup with external equipment

The projector has 37 preset data items for input signals in memory, which allows you to project a clear picture on the screen simply by connecting equipment and pressing the APA (Auto Pixel Alignment) key.

Easy presentation

•Multi functional Remote Commander with mouse control functions

You can operate a computer connected to this projector with the Remote Commander since the unit has a built-in mouse receiver.

•Digital zoom / freeze functions

This projector has a digital zoom function that enables you to enlarge the image at a desired location on the screen. The freeze function allows you to freeze the picture projected. The frozen picture continues to be projected even if the equipment is disconnected from the video source.

Accepts various input signals

•Scan converter loaded

This projector has a built-in scan converter that converts the input signal to 1024 × 768 dots (VPLPX15/PX10) or 800 × 600 dots (VPL-PS10).

•Compatible input signals

This projector accepts composite, S video, and component video signals as well as 15k RGB, VGA

SVGA

, XGA2), and SXGA2) signals, which can all be

displayed.

•Compatible with six color systems

Any of the NTSC

3.58, PAL, SECAM, NTSC4.43

M, or PAL-N color systems can be selected automatically or manually.

, PAL-

•Compatible with USB (Universal Serial Bus) hub

Other functions

functions

You can connect USB equipment (e.g., a USB mouse) to the projector, and also control the projector by using the “Projector Station” application software (CD-ROM) supplied with the projector from a

computer operated with Microsoft

Windows1) 98,

•Networking compatibility (Wireless compatible, VPL-PX15 only)

The projector is equipped with a PC CARD slot and ETHER connector, which allows you to connect the unit to a wired or wireless LAN.

Windows 98 SE or Windows 2000. Using this application software, you can open a file you want to use for your presentation with the supplied Remote Commander.

1) Microsoft and Windows are registered trademarks of Microsoft Corporation (U.S.A. and other countries).

2) VGA, SVGA, XGA and SXGA are registered trademarks of the International Business Machines Corporation, U.S.A.

3) NTSC4.43 is the color system used when playing back a video recorded on NTSC on an NTSC4.43 system VCR.

For information on the networking function of this projector, refer to the Operating Instructions for Networking supplied with the unit.

8 (GB)

Location and Function of

Location and Function of Controls

1 Zoom ring

Adjusts the size of the picture.

Controls

Front / Left Side

1 2 3

(This illustration shows the VPL-PX15.)

q;qa

H S U P

PUSH

2 Focus ring

Adjusts the picture focus.

3 Front remote control detector

4 Ventilation holes (exhaust)

5 Lens

Remove the lens cap before projection.

6 Adjuster buttons

7 Handle release Push to make the carrying handle 0 pop up.

8 Connector panel

For details, see “Connector Panel” on page 13 (GB).

9 Connector panel cover

If necessary, open this cover to use the connectors on the connector panel. You can remove the cover by releasing the connector panel cover lock qf.

Left side

Rear / Right Side / Bottom

qd qs ws ql wa w; ql qk qj

qgqf qh

PUSH

Connector panel cover

q; Carrying handle

Use the handle release 7 to make the handle pop up from the projector for carrying.

qa Control panel

For details, see “Control Panel” on page 11 (GB).

qs Rear remote control detector

qd Left speaker

9 (GB)

Location and Function of Controls

qf Connector panel cover lock Used to remove/install the connector panel cover 9.

Bottom

While pressing both sides of the lock, slide the connector cover outward to release it.

qg Rear adjusters qh Adjusters

When a picture is projected on an exterior of the screen, adjust the picture using these adjusters.

For details on how to use the adjusters, see “How to use the adjusters” on page 11 (GB).

wa Air filter cover lock

Used to remove the air filter cover.

For details, see “Cleaning the Air Filter” on page 38 (GB).

Note

Clean the air filter every 300 hours to ensure optimal performance.

ws Ventilation holes (intake) / air filter cover

Notes

•Do not place anything near the ventilation holes as it may cause internal heat build-up.

•Do not place your hand or objects near the ventilation holes — the air coming out is hot.

qj Security lock

Connects to an optional security cable (made by

Kensington)

The security lock corresponds to Kensington’s

®1)

MicroSaver

Security System.

If you require further information, contact

Kensington 2855 Campus Drive, San Mateo, CA 94403

In North America Phone: 800-235-6708 Fax: 800-247-1317

Outside North America Phone: 847-541-9500

Home page address: http://www.kensington.com/

qk Lamp cover ql Ventilation holes (intake) w; Right speaker

1) Kensington and MicroSaver are registered trademarks of Kensington Technology Group.

10 (GB)

Location and Function of Controls

How to use the adjusters

To adjust the height

Adjust the height of the projector as follows:

1 Lift the projector and press the adjuster buttons.

The adjusters will extend from the projector.

Adjuster buttons

2 While pressing the buttons, adjust the height.

Then, release the buttons. The adjusters will lock, then the height of the projector will be fixed. For fine adjustment, turn the adjusters to the right or left.

Control Panel

LAMP/

TEMP/

POWER

COVER

FAN

HELP

VOLUME

APA

RESET

12345678

1 HELP key

If you need help information during an operation, press this key to display help messages. The Help menu lists error recovery techniques depending on problem type.

2 VOLUME +/– keys

Adjust the volume of the built-in speakers.

+ : Increases the volume. – : Decreases the volume.

SAVING

ENTER

ON/

STANDBY

INPUT

Note

If the adjusters have been extended to the limit and you keep turning the adjusters counterclockwise, the adjusters will stop turning and the adjuster buttons cannot be pressed. In this case, turn the adjusters clockwise, and then press the adjuster buttons again.

3 If necessary, turn the rear adjusters to the right or

left to adjust the height of the projector.

3 APA (Auto Pixel Alignment) key

Adjusts the picture to be projected automatically to give the clearest picture possible while a signal from the computer is input. Adjusts the shift (up/down and left/right) at the same time automatically.

Note

Press the APA key when the full image is displayed on the screen. If there are black edges around the image, the APA function will not function properly and the image may extend beyond the screen.

4 RESET key

Resets the value of an item to its factory preset value. This key functions when the menu or a setting item is displayed on the screen.

5 Arrow (M/m/</,) keys

Used to select a menu or to make various adjustments.

6 ENTER key

Enters the settings of items in the menu system.

Notes

•Be careful not to let the projector down on your fingers.

•Do not push hard on the top of the projector with the adjusters out.

11 (GB)

Location and Function of Controls

7 INPUT key

Selects the input signal. Each time you press the key, the input signal switches as follows:

INPUT-A

INPUT -B (VPL-PX15 only)

S-VIDEO VIDEO

Notes

•You can select INPUT-B only if INPUT-B FUNC. in the INSTALL SETTING menu has been set to ON. INPUT-B is only available for the VPL-PX15.

•The audio signals are the same for the VIDEO and S-VIDEO.

•The audio signals are the same for the INPUT-A and INPUT-B.

8 I / 1 (on / standby) key

Turns the projector on and off when the projector is in the standby mode. The ON/STANDBY indicator lights in green when the power is turned on.

When turning off the power, press the I / 1 key twice following the message on the screen, or press and hold the key for about one second.

For details on steps for turning off the power, see “To turn off the power” on page 25 (GB).

9 MENU key

Displays the on-screen menu. Press again to clear the menu.

POWER SAVING: Lights up when the projector is

in the power saving mode. When POWER SAVING in the SET SETTING menu is set to ON, the projector goes into the power saving mode if no signal is input for 10 minutes. Although the lamp goes out, the cooling fan keeps running. The power saving mode is canceled when a signal is input or any key is pressed. However, in the power saving mode, none of the keys function for the first 60 seconds.

ON/STANDBY: Lights up or flashes under the

following conditions:

• Lights up in red when the AC power cord is plugged into the wall outlet. Once in the standby mode, you can turn on the projector

I / 1

with the

key.

• Lights up in green when the power is turned on.

• Flashes in green while the cooling fan runs after

I / 1

the power is turned off with the

key. The fan runs for about 90 seconds after turning off the power. The ON/STANDBY indicator flashes quickly for the first 60 seconds of that time. During this first 60 seconds, you cannot turn the

I / 1

power back on with the

For details on the LAMP/COVER and the TEMP/FAN indicators, see page 40 (GB).

key.

0 Indicators

LAMP/COVER: Lights up or flashes under the

following conditions:

• Lights up when the lamp has reached the end of its life or has reached a high temperature.

• Flashes when the lamp cover or air filter cover is not secured firmly.

TEMP (Temperature)/FAN: Lights up or flashes

under the following conditions:

• Lights up when temperature inside the projector becomes unusually high.

• Flashes when the fan is broken.

12 (GB)

Location and Function of Controls

Connector Panel

Left side

PUSH

INPUT B PC CARD

4321

(This illustration shows the VPL-PX15.)

1 AC IN socket

Connects the supplied AC power cord.

AUDIO

MOUSE

PLUG IN POWER

CTRL S

AUDIO

VIDEO

INPUT A ~AC IN

56 7 8

MOUSE

PLUG IN POWER

CTRL S

AUDIO

INPUT A ~AC IN

4 INPUT B connectors (VPL-PX15 only)

INPUT B PC CARD slot (Type II): A wireless

LAN PC card or PC memory card can be installed according to your requirements.

For details, see “Installing a PC card” on page 21 (GB).

INPUT B ETHER connector (10BASE-T/

100BASE-TX): Connects to a computer on a

LAN with a LAN cable when you use the

S VIDEO

networking function of this projector.

5 MOUSE connector (6-pin)

Connects to the PS/2 mouse port on a computer via the supplied mouse cable, to control the mouse function of the connected computer.

AUDIO

VIDEO

S VIDEO

6 USB connector (USB B-plug for upstream, 4pin)

Connects to a computer. When you connect the projector to the computer via this connector, the projector recognizes that a USB mouse is connected and you can control the mouse function of the computer connected to the INPUT A connector using the supplied Remote Commander. The supplied application software can be used on the computer connected to this connector.

2 INPUT A connectors

Connect to external equipment such as a computer.

INPUT A connector (HD D-sub 15-pin, female):

Connects to the monitor output on a computer using the supplied cable. When inputting a component or 15k RGB signal, use the appropriate cable.

For details, see “To connect 15k RGB/Component equipment” on page 21 (GB).

AUDIO jack (stereo minijack): Connects to the

audio output of the computer.

3 CTRL S /PLUG IN POWER (DC 5V output) jack (stereo minijack)

Connects to the control S out jack of Sony equipment. Connects to the CONTROL S OUT jack on the supplied Remote Commander to use it as a wired remote control unit. In this case, you do not need to install batteries in the Remote Commander, since the power is supplied from this jack.

7 USB connector (USB A-plug for downstream, 4pin)

Connects to USB equipment such as a mouse, camera, etc.

8 Video input connectors

Connect to external video equipment such as a VCR.

S VIDEO connector (mini DIN 4-pin): Connects to

the S video output (Y/C video output) of video equipment.

VIDEO jack (phono type): Connects to the

composite video output of video equipment.

AUDIO jack (stereo minijack): Connects to the

audio output of the VCR.

13 (GB)

Location and Function of Controls

Remote Commander (supplied with the VPL-PX15/PX10)

Keys which have the same names as those on the control panel function identically.

MUTING

AUDIO

VOLUME

ENTER

RESET/

ESCAPE

FUNCTION

RM-PJM15

PROJECTOR

qs,qd

PIC

INPUT

D KEYSTONE

FREEZE

LASER

CLICK

1 2 3

4 5

6 7 8

9 q;

wd ws

COMMAND

OFF

PJ NETWORK

wa w; ql qk

HELP

APA

MENU/

TAB

qj qh

qg qf

D ZOOM

Notes on the laser beam

•Do not look into the laser transmitter.

•Do not aim the laser at people.

I / 1

1 2 MUTING keys

Cut off the picture and sound.

3 INPUT key 4 D KEYSTONE key

Corrects the trapezoidal distortion caused by the projection angle. Use the arrow keys (M/m/</,) to display the image as a rectangle.

5 FREEZE key

Used to freeze the picture projected. To cancel the frozen picture, press the key again.

(on / standby) key

PIC: Cuts off the picture. Press again to restore the

picture.

AUDIO: Cuts off the sound from the speakers. Press

again or press the VOLUME + key to restore the sound.

7 Mouse

When the PJ/NETWORK select switch is set to

PJ: Functions as the mouse of the computer

connected to this projector.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): Functions as the

mouse in the INPUT B window of this projector.

8 Arrow (M/m/</,) keys 9 R (right) CLICK key

When the PJ/NETWORK select switch is set to

PJ: Functions as the right button of the mouse of

the computer connected to this projector.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): Functions as the

right button of the mouse in the INPUT B window of this projector.

0 ENTER key qa FUNCTION 1, 2, 3 keys

When the PJ/NETWORK select switch is set to

PJ: Functions when the supplied application

software is used. When you connect the projector with a computer, you can open a file on the screen by just pressing a FUNCTION key. This will enhance your presentation. To use this function, allocate a file to the FUNCTION key by using the application software. (Only the FUNCTION 1 and 2 keys are available. You cannot allocate a file to the FUNCTION 3 key.)

For details, see the README file and HELP file supplied with the application software.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): When the

INPUT B window is displayed on the projector, you can start an application by just pressing a FUNCTION key. To use this function, allocate an application to a FUNCTION key. (The FUNCTION 3 key is allocated to the keyboard software display.)

qs Strap holder

Attaches the strap.

qd CONTROL S OUT jack (stereo minijack)

Connects to the CTRL S jack on the projector with the connecting cable (not supplied) to use the Remote Commander as a wired remote control unit. In this case, you do not need to install batteries in the Remote Commander since the power is supplied via the CTRL S jack on the projector.

6 LASER key

Emits a laser beam from the laser transmitter while you keep this key pressed.

14 (GB)

Location and Function of Controls

qf RESET/ESCAPE key

When the PJ/NETWORK select switch is set to

PJ: Functions as the RESET key.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): Functions as the

ESCAPE key of the keyboard when the INPUT B window is displayed.

qg D ZOOM +/– key

Enlarges the image at a desired location on the screen. This key works only when a signal from a computer is input.

+: Pressing the + key once displays the icon. This

icon indicates the point you want to enlarge. Use an arrow key (M/m/</,) to move the icon to the point to be enlarged. Press the + key repeatedly until the image is enlarged to meet your requirements.

–: Each press of the – key reduces an image that has

been enlarged with the D ZOOM + key.

qh L (left) CLICK key

When the PJ/NETWORK select switch is set to

PJ: Functions as the left button of the mouse of

the computer connected to this projector.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): Functions as the

left button of the mouse in the INPUT B window of this projector.

wd Transmission indicator

Lights up when you press a key on the Remote Commander. This indicator does not light up when you use the laser pointer.

wf Infrared transmitter wg Laser transmitter

qj MENU/TAB key

When the PJ/NETWORK select switch is set to

PJ: Functions as the MENU key.

When the PJ/NETWORK select switch is set to

NETWORK (VPL-PX15 only): Functions as the

TAB key of the keyboard when the INPUT B window is displayed.

qk APA (Auto Pixel Alignment) key ql VOLUME +/– keys w; HELP key

If you need help information during an operation, press this key to display help messages.

wa PJ/NETWORK select switch

To use the Remote Commander for network operations, set the switch to NETWORK. Set the switch to PJ to use the Remote Commander for normal operations other than networking. This switch is only available for the VPL-PX15.

For details on the operation of the Windows CE screen, see the supplied “Operating Instructions for Networking.”

ws COMMAND ON/OFF switch

When this switch is set to OFF, no keys on the Remote Commander will function. This saves battery power.

15 (GB)

Location and Function of Controls

Battery installation

1 Push and slide to open the lid, then install the two

R6 (size AA) batteries (supplied) with the correct polarity.

Slide while pressing down on the lid.

Be sure to install the battery from the # side.

2 Replace the lid.

Notes on batteries

•Make sure that the battery orientation is correct when inserting batteries.

•Do not mix an old battery with a new one, or different types of batteries.

•If you do not intend to use the Remote Commander for a long time, remove the batteries to avoid damage from battery leakage. If batteries have leaked, remove them, wipe the battery compartment dry and replace the batteries with new ones.

Remote Commander (supplied with the VPL-PS10)

Keys which have the same names as those on the control panel function identically.

qh qg qf qd qs qa

FREEZE

INPUT

MENU ENTER

+ –

D ZOOM

I / 1

MS SLIDE

D KEYSTONE

APA

RESET

CLICK

FUNCTION

1 2

3 4

Notes on Remote Commander operation

•Make sure that there is nothing to obstruct the infrared beam between the Remote Commander and the remote control detector on the projector.

•The operation range is limited. The shorter the distance between the Remote Commander and the projector is, the wider the angle within which the commander can control the projector.

I / 1

(on / standby) key

2 APA (Auto Pixel Alignment) key

3 ENTER key

4 Joystick

Functions as the mouse of the computer connected to this projector.

5 Arrow (M/m/</,) keys

6 R (right) CLICK key

Functions as the right button of a mouse.

7 FUNCTION 1, 2 keys

Functions when the supplied application software is used. When you connect the projector with a computer, you can open a file on the screen by just pressing a FUNCTION key. This will enhance your presentation. To use this function, allocate a file to the FUNCTION key by using the application software.

For details, see the README file and HELP file supplied with the application software.

16 (GB)

Location and Function of Controls

8 RESET key

Resets the value of an item to its factory preset value or returns the enlarged image back to its original size.

9 D ZOOM +/– key

Enlarges the image at a desired location on the screen. This key works only when a signal from a computer is input.

+: Pressing the + key once displays the icon. This

–: Each press of the – key reduces an image that has

been enlarged with the D ZOOM + key.

0 L (left) CLICK key

Functions as the left button of a mouse.

qa MENU key

qs D KEYSTONE key

Corrects the trapezoidal distortion caused by the projection angle. Use the arrow keys (M/m/</,) to display the image as a rectangle.

qd INPUT key

qf FREEZE key

Used to freeze the picture projected. To cancel the frozen picture, press the key again.

qg MS SLIDE key

This key does not operate with this unit.

Battery installation

1 Push and slide to open the lid, then install the two

R6 (size AA) batteries (supplied) with the correct polarity.

Slide while pressing down on the lid.

Be sure to install the battery from the # side.

2 Replace the lid.

Notes on batteries

•Make sure that the battery orientation is correct when inserting batteries.

•Do not mix an old battery with a new one, or different types of batteries.

Notes on Remote Commander operation

•Make sure that there is nothing to obstruct the infrared beam between the Remote Commander and the remote control detector on the projector. Direct the Remote Commander toward the front or rear remote control detector.

•The operation range is limited. The shorter the distance between the Remote Commander and the projector is, the wider the angle within which the commander can control the projector.

qh Infrared transmitter

17 (GB)

Installing the Projector / Connecting the Projector

Installing the Projector

This section describes how to install the projector. The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide.

PUSH

Distance between the screen and the center of the lens

Unit: m (feet)

Screen

size 40 60 80 100 120 150 180 200 250 300

(inches)

Minimum 1.5 2.2 3.0 3.7 4.5 5.6 6.8 7.5 9.4 11.3

Distance (4.8) (7.3) (9.8) (12.3) (14.8)(18.5)(22.3)(24.8)(31.0)(37.3)

Maximum 1.8 2.7 3.6 4.5 5.4 6.8 8.1 9.1 11.3 13.6

Distance (5.8) (8.8) (11.8) (14.8) (17.8) (22.2) (26.7) (29.7) (37.2) (44.7)

For details, see “Installation Example” on page 34 (GB). For details on ceiling installation, consult with qualified Sony personnel (fee charged).

Connecting the Projector

When making connections, be sure to do the following:

•Turn off all equipment before making any connections.

•Use the proper cables for each connection.

•Insert the cable plugs properly; plugs that are not fully inserted often generate noise or cause picture degradation. When pulling out a cable, be sure to pull it out grasping the plug, not the cable itself.

Connecting to a Computer

This section describes how to connect the projector to a computer. For more information, refer to the computer’s instruction manual.

Notes

•The projector accepts VGA, SVGA, XGA, and SXGA signals. However, we recommend that you set the output mode of your computer to SVGA (VPL-PS10) or XGA (VPL-PX15/PX10) mode for the external monitor.

•If you set your computer, such as a notebook type, to output the signal to both your computer’s display and an external monitor, the picture of the external monitor may not appear properly. Set your computer to output the signal to only the external monitor.

For details, refer to the operating instructions supplied with your computer.

•The supplied mouse cable may not work properly depending on your computer.

•This projector is compatible with DDC2B (Display Data Channel 2B). If your computer is compatible with DDC following procedures.

, turn the projector on according to the

1 Connect the projector to the computer using the

supplied HD D-sub 15-pin cable.

2 Turn the projector on. 3 Start the computer.

1) DDC™ is a registered trademark of the Video Electronics Standards Association.

18 (GB)

Connecting the Projector

To connect an IBM1) PC/AT1) compatible computer

When you use a USB mouse and USB equipment

Left side

to USB equipment

MOUSE

PLUG IN POWER

CTRL S

Stereo audio connecting cable (not supplied)

to audio output

AUDIO

INPUT A ~AC IN

USB cable A type – B type (supplied)

to USB connector

VIDEO

S VIDEO

HD D-sub 15-pin

cable (supplied)

to monitor output

On the USB function

When connecting the projector to a computer using the USB cable for the first time, the computer recognizes the following devices automatically.

1 USB hub (general use) 2 USB human interface device (wireless mouse

function)

3 USB human interface device (projector control

function) The computer also recognizes the device connected to the downstream connector on the projector.

Recommended operating environment

When you use the USB function, connect your computer as illustrated in the box on the left. This application software and the USB function can be used on a computer loaded with Windows 98, Windows 98 SE or Windows 2000.

Notes

• As the projector recognizes the USB mouse when

the computer is connected to the USB connector, do not connect anything to the MOUSE connector.

• Your computer may not start correctly when

connected to the projector via the USB cable. In this case, disconnect the USB cable, restart the computer, then connect the computer to the projector using the USB cable.

• This projector is not guaranteed for suspend or

standby mode. When you use the projector in suspend or standby mode, disconnect the projector from the USB port on the computer.

• Operations are not guaranteed for all the

recommended computer environments.

Setting Up and Projecting

Computer

1) IBM® and PC/AT are a trademark and a registered trademark of International Business Machines Corporation, U.S.A.

19 (GB)

Connecting the Projector

When you use a PS/2 mouse port

Left side

MOUSE

PLUG IN POWER

CTRL S

PS/2 Mouse cable (supplied)

to mouse port (PS/2)

AUDIO

INPUT A ~AC IN

Stereo audio connecting cable (not supplied)

to audio output

VIDEO

HD D-sub 15-pin

cable (supplied)

to monitor output

S VIDEO

Connecting to a VCR or 15k RGB/

Component Equipment

This section describes how to connect the projector to

a VCR or 15k RGB/component equipment.

For more information, refer to the instruction manuals

of the equipment you are connecting.

To connect a VCR

Left side

MOUSE

PLUG IN POWER

CTRL S

AUDIO

INPUT A ~AC IN

Stereo audio connecting cable (not supplied)

VIDEO

Video cable (not supplied)

S VIDEO

S-Video cable (not supplied)

Computer

To connect a Macintosh1) computer

Use an ADP-20 signal adapter (not supplied). In this case, however, you cannot control the mouse of the computer using the Remote Commander.

to audio output

to video output

VCR

to S video output

1) Macintosh is a registered trademark of Apple Computer, Inc.

20 (GB)

Connecting the Projector

To connect 15k RGB/Component equipment

Left side

MOUSE

PLUG IN POWER

CTRL S

Stereo audio connecting cable (not supplied)

to audio output

AUDIO

INPUT A ~AC IN

SMF-402 Signal Cable (not supplied) HD D-sub 15-pin (male) y 3 × phono jack

to RGB/ component output

VIDEO

S VIDEO

Connecting to a LAN (VPL-PX15 only)

This projector is networking compatible. Using a wireless LAN PC card or a 10BASE-T/100BASE-TX LAN cable, you can connect the projector to a wireless or wired LAN. You can also install a PC memory card. This section describes how to connect to a LAN and how to install a PC card. Whenever you connect the projector to a LAN or use a memory card, set INPUT-B FUNC. in the INSTALL SETTING menu to ON.

For details, see page 33 (GB).

Installing a PC card

When you use a wireless LAN PC card or memory card, insert the card into the INPUT B PC CARD slot.

15k RGB/Component equipment

Notes

• Set the aspect ratio using ASPECT in the INPUT SETTING menu according to the input signal.

For details, see page 30 (GB).

• When you connect the projector to 15k RGB/ component video equipment, select RGB, component or VCR GBR with the INPUT-A setting in the SET SETTING menu.

• Use the composite sync signal when you input the external sync signal from 15k RGB/component equipment.

The eject button pops out when the card is inserted.

PUSH

PC card

Insert the card with the arrow mark

facing toward the slot.

To remove the PC card from the slot, press the eject button.

21 (GB)

Connecting the Projector

Connection using a wireless LAN PC card

Wireless LAN PC card (IEEE802.11b compliant) (recommended)

Computer

Wireless LAN access point (IEEE802.11b compliant) (recommended)

Wireless LAN PC card (IEEE802.11b compliant) (specified)

PUSH

INPUT B PC CARD

INPUT A ~AC IN

Left side of the projector

Connection using a wireless LAN PC card (Peer to Peer mode)

Computer

Wireless LAN PC card (IEEE802.11b compliant) (recommended)

Left side of the projector

PUSH

INPUT B PC CARD

INPUT A ~AC IN

to Hub/router

Wireless LAN PC card (IEEE802.11b compliant) (recommended)

Computer

Wireless LAN PC card (IEEE802.11b compliant) (specified)

Notes

•For details on the recommended PC card or wireless LAN access point, see the supplied “Specified/ recommended PC Card/Wireless LAN Access Point.”

•When you use a LAN, you must set the IP address. For details on how to set the IP address, etc., see the supplied “Operating Instructions for Networking.”

22 (GB)

Connecting using the ETHER connector

LAN cable

Computer

Connecting the Projector / Selecting the Menu Language

Selecting the Menu Language

You can select the language to be used in the menu and other on screen displays from 9 languages. The factory setting is ENGLISH.

4,5,6 3 2

LAMP/

TEMP/

POWER

COVER

FAN

SAVING

ON/

STANDBY

to router

LAN cable

Hub

Left side of the projector

to INPUT B EHTER connector

Computer

PUSH

INPUT B PC CARD

Computer

INPUT A ~AC IN

VOLUME

APA

HELP

RESET

ENTER

INPUT

ENTER key

1 Plug the AC power cord into the wall outlet. 2 Press the I /

key to turn on the power.

3 Press the MENU key.

The menu display appears.

4 Press the M or m key to select the SET SETTING

Installing a memory card

If you store a file created with Microsoft PowerPoint in a memory card and insert it into the INPUT B PC CARD slot, you can run a presentation without connecting a computer.

For inserting and removing a memory card, see “Installing a PC card” on page 21 (GB). For details on the recommended memory card, see the supplied “Specified/recommended PC Card/Wireless LAN Access Point.”

1) PowerPoint is a registered trademark of Microsoft Corporation (U.S.A. and other countries).

menu, then press the , or ENTER key. The SET SETTING menu appears.

SET SETTING

STATUS: ON INPUT-A: COMPUTER AUTO INPUT SEL

LANGUAGE POWER SAVING IR RECEIVER

: OFF

: ENGLISH

: OFF

: FRONT&REAR

INPUT-A

23 (GB)

Selecting the Menu Language / Projecting

5 Press the M or m key to select LANGUAGE, then

press the , or ENTER key.

6 Press the M or m key to select a language, then

press the < or ENTER key. The menu changes to the selected language.

To clear the menu display

Press the MENU key. The menu display disappears automatically if no key is pressed for one minute.

Projecting

APA key

VOLUME

APA

ON/STANDBY indicator

LAMP/

TEMP/

COVER

HELP

RESET

FAN

POWER SAVING

STANDBY

ENTER

ON/

INPUT

1 After all equipment is connected completely, plug

the AC power cord into the wall outlet. The ON/STANDBY indicator lights in red and the projector goes into the standby mode.

2 Press the I /

key to turn on the projector.

The ON/STANDBY indicator lights in green.

3 Turn on all equipment connected to the projector.

Press the INPUT key to select the input source. INPUT-A: Selects the video signal input from the

INPUT A connector.

INPUT-B (VPL-PX15 only): Selects display of

the INPUT B (Windows CE) window.

VIDEO: Selects the video signal input from the

VIDEO jack on the video input connectors.

S-VIDEO: Selects the video signal input from the

S VIDEO connector on the video input connectors.

4 Turn the zoom ring to adjust the size of the

picture.

5 Turn the focus ring to adjust the focus.

Rear remote control detector

COMMAND

OFF

PJ NETWORK

HELP

APA

MENU/

TAB

PIC

MUTING

AUDIO

VOLUME

INPUT

D KEYSTONE

FREEZE

LASER

2 3

APA key

FREEZE

INPUT

MENU ENTER

+ –

ENTER

CLICK

RESET/ ESCAPE

D ZOOM

for VPL-PX15/PX10 for VPL-PS10

FUNCTION

RM-PJM15

PROJECTOR

D ZOOM

I / 1

MS SLIDE

D KEYSTONE

APA

RESET

CLICK

FUNCTION

Note

Looking into the lens when the projector is projecting an image may cause injury to your eyes.

To cut off the picture

Press the PIC MUTING key on the Remote Commander (VPL-PX15/PX10 only). To restore the picture, press the PIC MUTING key again.

To get the clearest picture

You can get the best picture automatically when a signal from the computer is input. Press the APA key. The picture is automatically adjusted to project the clearest picture possible.

24 (GB)

Projecting

Notes

•Adjust the signal when a still picture is displayed on the screen.

•Press the APA key when the full image is displayed on the screen. If there are black edges around the image, the APA function will not function properly and the image may extend beyond the screen.

•If you switch the input signal or re-connect a computer, press the APA key again to get the suitable picture.

•“ADJUSTING” appears on the screen. To restore the original screen, press the APA key again during the adjustment.

•“Complete!” appears on the screen when the picture is adjusted properly. However, depending on the kinds of input signal, the picture may not always be adjusted properly.

•Adjust the items in the INPUT SETTING menu when you adjust the picture manually.

For details on the INPUT SETTING menu, see page 29 (GB).

To correct trapezoidal distortion

When the projected image is a trapezoid, correct it by pressing the D KEYSTONE key on the Remote Commander or by adjusting DIGIT KEYSTONE in the INSTALL SETTING menu.

To turn off the power

1 Press the I /

“Power OFF?” appears on the screen.

Note

The message will disappear if you press any key except the I / key for five seconds.

2 Press the I /

The ON/STANDBY indicator flashes in green and the fan continues to run for about 90 seconds to reduce internal heat build-up. Also, the ON/ STANDBY indicator flashes quickly for the first 60 seconds. During this first 60 seconds, you will not be able to turn the power back on with the

key.

I /

key.

key, or if you do not press any

key again.

3 Unplug the AC power cord from the wall outlet

after the fan stops running and the ON/STANDBY indicator lights in red.

When you cannot confirm the on-screen message

When you cannot confirm the on-screen message at

anytime, you can turn off the power by holding the

key for about one second.

I /

When the base edge is longer than the upper edge as shown in the figure below:

Set the value to negative.

When the upper edge is longer than the base edge as shown in the figure below:

Set the value to positive.

For details on “DIGIT KEYSTONE,” see page 33 (GB).

Note

Do not unplug the AC power cord while the fan is still running; otherwise, the fan will stop even though the internal heat level is still high. This may lead to a breakdown of the projector.

Cleaning the air filter

Clean the air filter every 300 hours to ensure

optimal performance.

25 (GB)

Projecting

To enlarge the image (Digital Zoom function)

You can enlarge an area on the image you select. This function works only when a signal from a computer is input.

1 Project the original size picture and press the D

ZOOM + key on the Remote Commander. The Digital Zoom icon appears in the center of the image.

Digital Zoom icon

2 Move the icon to a point in the center of the

portion of the image you want to enlarge. Use the arrow keys (M/m/</,) to move the icon.

3 Press the D ZOOM + key again.

The portion of the image where the icon is located is enlarged. The magnification ratio is displayed on the screen for a few seconds. By pressing the + key repeatedly, the image size increases (maximum magnification: 4 times) .

To freeze the image projected (Freeze function)

Press the FREEZE key. “FREEZE” appears when the key is pressed. This function works only when a signal from a computer is input. To restore the original screen, press the FREEZE key again.

To use the Laser Pointer function (VPLPX15/PX10 only)

Press the LASER key on the Remote Commander. The laser pointer appears. The pointer is helpful in indicating a particular point on the screen.

Use the arrow keys (M/m/</,) to scroll the enlarged image.

To return the image to its original size

Press the D ZOOM – key. Pressing the RESET key returns the image to its original size in one operation.

26 (GB)

Using the Menu

The projector is equipped with an on-screen menu for making various adjustments and settings.

Note

(VPL-PX15/PX10 only)

Before operation, confirm that the PJ/NETWORK select switch on the Remote Commander is set to PJ. If it is set to NETWORK, the menu display will not appear even when you press the MENU key on the Remote Commander.

To select the language used in the menu, see page 23 (GB).

1 Press the MENU key.

The menu display appears. The menu presently selected is shown as a yellow button.

PICTURE CTRL

CONTRAST: 80 BRIGHT: 50 RGB ENHANCER: GAMMA MODE: COLOR TEMP: LOW VOLUME: 50

30 GRAPHICS

INPUT-A

To clear the menu

Press the MENU key. The menu display disappears automatically if no key is pressed for one minute.

To reset items that have been adjusted

Press the RESET key. “Complete!” appears on the screen and the settings appearing on the screen will be reset to their factory preset values. Items that can be reset are:

•“CONTRAST, ” “BRIGHT, ” “COLOR, ” “HUE,” “SHARP,” and “RGB ENHANCER” in the PICTURE CTRL menu.

•“DOT PHASE, ” “SIZE H,” and “SHIFT” in the INPUT SETTING menu.

•“DIGIT KEYSTONE” in the INSTALL SETTING menu.

About the retention of the settings

The settings are automatically stored in the projector memory.

Adjustments and Settings Using the Menu

2 Use the M or m key to select a menu, then press

the , or ENTER key. The selected menu appears.

Menus Setting items

SET SETTING

STATUS: ON INPUT-A: COMPUTER AUTO INPUT SEL:

POWER SAVING: IR RECEIVER:

LANGUAGE

OFF

: ENGLISH

OFF FRONT&REAR

INPUT-A

3 Select an item.

Use the M or m key to select the item, then press the , or ENTER key.

4 Make settings or adjustments on an item.

For details on setting individual items, see the relevant menu pages.

When no signal is input

When there is no input signal, “NO INPUT–Cannot adjust this item.” appears on the screen, and the items mentioned above cannot be adjusted.

About the menu display

You can set the display position of the menu, the intensity of the background picture, and the color of the menu items as you like.

For details, see page 33 (GB).

27 (GB)

The PICTURE CTRL Menu

The PICTURE CTRL (control) menu is used for adjusting the picture. Unadjustable items for a particular input signal are not displayed in the menu.

When the video signal is input

PICTURE CTRL

CONTRAST: 80 BRIGHT: 50 COLOR: 50 HUE: 50 SHARP: 50 D.PICTURE: ON COLOR TEMP: LOW COLOR SYS: AUTO VOLUME: 50

When the RGB signal is input

PICTURE CTRL

CONTRAST: 80 BRIGHT: 50 RGB ENHANCER: GAMMA MODE: COLOR TEMP: LOW VOLUME: 50

30 GRAPHICS

VIDEO

INPUT-A

BRIGHT

Adjusts the picture brightness. The higher the setting, the brighter the picture. The lower the setting, the darker the picture.

COLOR

Adjusts color intensity. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity.

HUE

Adjusts color tones. The higher the setting, the more the picture becomes greenish. The lower the setting, the more the picture becomes purplish.

SHARP

Adjusts the picture sharpness. The higher the setting, the sharper the picture. The lower the setting, the softer the picture.

RGB ENHANCER

Operation

1. Select an item

Use the M or m key to select the item, then press the , or ENTER key.

2. Adjust an item

•When changing the adjustment level: To increase the value, press the M or , key. To decrease the value, press the m or < key. Press the ENTER key to restore the original screen.

•When changing the setting: Press the M or m key to change the setting. Press the ENTER or < key to restore the original screen.

CONTRAST

Adjusts the picture sharpness when RGB signals are input. The higher the setting, the sharper the picture. The lower the setting, the softer the picture.

D. (Dynamic) PICTURE

Emphasizes the black color.

ON: Emphasizes the black color to produce a bolder

“dynamic” picture.

OFF: Reproduces the dark portions of the picture

accurately, in accordance with the source signal.

GAMMA MODE

Selects a gamma correction curve.

GRAPHICS: Improves the reproduction of half

tones. Photos can be reproduced in natural tones.

TEXT: Contrasts black and white. Suitable for

images that contain lots of text.

Adjusts the picture contrast. The higher the setting, the greater the contrast. The lower the setting, the lower the contrast.

28 (GB)

COLOR TEMP

Adjusts the color temperature.

HIGH: Makes the white color bluish. LOW: Makes the white color reddish.

COLOR SYS (System)

Selects the color system of the input signal.

AUTO: Automatically selects one of the following

signals: NTSC

PAL-M/N: Automatically selects one of the

following signals: PAL-M/PAL-N, NTSC Normally, set to AUTO. If the picture is distorted or colorless, select the color system appropriate to the input signal.

3.58, PAL, SECAM, NTSC4.43.

3.58.

The PICTURE CTRL Menu / The INPUT SETTING Menu

The INPUT SETTING Menu

The INPUT SETTING menu is used to adjust the input signal. Unadjustable items for a particular input signal are not displayed in the menu.

When the video signal is input

INPUT SETTING

SHIFT H: 200 V: 30 ASPECT: 16:9

VIDEO

VOLUME

Adjusts the volume. The volume can be adjusted for each of INPUT A, INPUT B (VPL-PX15 only), VIDEO and S VIDEO input.

Input signals and adjustable/setting items

Item Input signal

Video or S video (Y/C)

CONTRAST BRIGHT COLOR –

(

except for B & W

HUE –

SHARP – RGB

ENHANCER D. PICTURE GAMMA – – –

MODE COLOR

TEMP COLOR

SYS VOLUME

(NTSC3.58/

4.43 only)

–––

Component

)

–––

: Adjustable/can be set

– : Not adjustable/can not be set

1) The RGB signals of a computer

Video GBR

––

RGB

NO.01 VIDEO/60

When the RGB signal is input

INPUT SETTING

DOT PHASE: 0 SIZE H: 1056 SHIFT H: 200 V: 30 SCAN CONV: ON

NO.17 800x600

INPUT-A

Memory No.

Signal type

Memory No.

Signal type

Operation

1. Select an item

Use the M or m key to select the item, then press the , or ENTER key.

2. Adjust an item

•When changing the adjustment level: To increase the value, press the M or , key. To decrease the value, press the m or < key. Press the ENTER key to restore the original screen.

•When changing the setting: Press the M or m key to change the setting. Press the ENTER or < key to restore the original screen.

DOT PHASE

Adjusts the dot phase of the LCD panel and the signal input from the INPUT A/B connector. Adjust the picture further for a finer picture after the picture is adjusted by pressing the APA key. Adjust the picture to the point where it looks clearest.

29 (GB)

The INPUT SETTING Menu

SIZE H

Adjusts the horizontal size of the picture input from the INPUT A/B connector. The higher the setting, the larger the horizontal size of the picture. The lower the setting, the smaller the horizontal size of the picture. Adjust the setting according to the dots of the input signal.

For details on a suitable value for preset signals, see page 31 (GB).

SHIFT

Adjusts the position of the picture input from the INPUT A/B connectors or video input connectors. H adjusts the horizontal position of the picture. V adjusts the vertical position of the picture. As the setting for H increases, the picture moves to the right, and as the setting decreases, the picture moves to the left. As the setting for V increases, the picture moves up, and as the setting decreases, the picture moves down. Use the < or , key to adjust the horizontal position and the M or m key for the vertical position.

ASPECT

Sets the aspect ratio of the picture. When inputting a 16:9 (squeezed) signal from equipment such as a DVD player, set this to 16:9.

4:3 : When a picture with a ratio of 4:3 is input. 16:9 : When a picture with a ratio of 16:9 (squeezed)

is input.

SCAN CONV (Scan converter)

Input signals and adjustable/setting items

Item Input signal

Video or Video GBR RGB S video (Y/C)

DOT – – – PHASE

SIZE H – – – SHIFT ASPECT – SCAN – – –

CONV

: Adjustable/can be set

– : Not adjustable/can not be set

1) The RGB signals of a computer

2) VPL-PX15/PX10: lower than SVGA only; VPL-PS10:

lower than VGA only

Component

About the preset memory No.

This projector has 37 kinds of preset data for input signals (the preset memory). The memory number of the current input signal and the signal type are displayed when the preset signal is input. This projector automatically detects the signal type. When the signal has been registered in the preset memory, a suitable picture is displayed on the screen according to the signal type. You can adjust the picture through the INPUT SETTING menu. This projector also has 20 kinds of user memories for each INPUT A/B. When an unpreset signal is input for the first time, the memory number is displayed as

0. If the input signal is adjusted in the INPUT SETTING menu, the setting made via INPUT A/B is stored. When more than 20 user memory items are registered for each INPUT A/B, the newest memory item is automatically stored over the oldest one.

Converts the signal to display the picture according to the screen size.

ON: Displays the picture according to the screen

size. The picture will lose some clarity.

OFF: Displays the picture while matching one pixel

of the input picture element to that of the LCD. The picture will be clear but the picture size will be smaller.

Note

This item will not be displayed in the following cases. VPL-PX15/PX10: When an XGA or SXGA signal is input. VPL-PS10: When an SVGA, XGA or SXGA signal is input.

30 (GB)

+ 98 hidden pages