Sony VPL-FX200U, VPL-FX200E, VPL-FX200M Operating Instruction

VPL-FX200U/FX200E/FX200M

3-867-467-11(1)

LCD Data Projector

Operating Instructions

Mode d’emploi

Manual de instrucciones

VPL-FX200U VPL-FX200E VPL-FX200M

 1999 Sony Corporation

English

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For the customers in the United Kingdom

WARNING THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Voor de klanten in Nederland

Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

The socket-outlet should be installed near the equipment and be easily accessible.

For the customers in the USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-

003.

2 (GB)

Table of Contents

Overview

Setting up and projecting

Adjustments and settings using the menu

Precautions ............................................................... 4 (GB)

Features..................................................................... 6 (GB)

Location and Function of Controls ......................... 8 (GB)

Front .............................................................................. 8 (GB)

Rear ............................................................................. 12 (GB)

Remote Commander ................................................... 14 (GB)

Precautions on Installation.................................... 18 (GB)

Installing the Projector on the Floor ..................... 19 (GB)

Connecting with a Computer or a VCR ................ 20 (GB)

Projecting ................................................................ 21 (GB)

Using the Menu ....................................................... 24 (GB)

The PICTURE CTRL Menu ..................................... 25 (GB)

The INPUT SETTING Menu .................................... 27 (GB)

The SET SETTING Menu ........................................ 30 (GB)

The SIGNAL SELECT Menu ................................... 32 (GB)

English

Connection examples/ Index number setting

Maintenance

Others

Connection Examples ............................................ 33 (GB)

Connecting 15k RGB/Component Equipment............ 33 (GB)

Connecting the Switcher ............................................. 34 (GB)

Confirming the System Construction.......................... 35 (GB)

Setting the Index Numbers .................................... 36 (GB)

Maintenance ............................................................ 39 (GB)

Replacing the Lamp .................................................... 39 (GB)

Cleaning the Air Filter................................................. 40 (GB)

Troubleshooting...................................................... 41 (GB)

Specifications ......................................................... 43 (GB)

Index ........................................................................ 46 (GB)

3 (GB)

Precautions

On safety

• Check that the operating voltage of your unit is identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel.

• Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified Sony personnel before operating it further.

• Unplug the unit from the wall outlet if it is not to be used for several days.

• To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The wall outlet should be near the unit and easily accessible.

• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Do not look into the lens while the lamp is on.

• Do not place your hand or objects near the ventilation holes — the air coming out is hot.

On installation

On illumination

• When the projector is mounted on the ceiling, the Sony PSS-2000 Projector Suspension Support must be used for installation.

• Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. Leave space of more than 30 cm (11 room heat rises to the ceiling; check that the temperature near the installation location is not excessive.

• Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity, mechanical vibration or shock.

• To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight.

• Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio.

• Cover any windows that face the screen with opaque draperies.

• It is desirable to install the projector in a room where floor and walls are not of light-reflecting material. If the floor and walls are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color.

/8 inches) between the wall and the projector. Be aware that

4 (GB)

On preventing internal heat build-up

After turning off the power, the cooling fan runs for about six minutes while the ON indicator flashes in green. The indicator flashes quickly for one minute. During that time, you will not be able to turn the power back on with the ON key.

Caution

The projector is equipped with ventilation holes (intake) at the bottom/ front side and ventilation holes (exhaust) at the left/right side. Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

On cleaning

• To keep the cabinet looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents, such as thinner, benzene, or abrasive cleansers, since these will damage the cabinet.

• Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

• Clean the air filter in every 100 hours.

Overview

On repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory.

5 (GB)

Features

High brightness, high picture quality

• High brightness

Adopting four 120 W UHP lamps and newly developed optical system povides high brightness (light output 3,100 of ANSI lumen) and excellent uniformity on the picture.

• High resolution

Thanks to use of three 1.8-inch XGA pixels, the projector can project the sharp picture with the resolution of 1024 × 768 pixels.

• DRC (Digital Reality Creation)

The DRC technology allows you to obtain a finer, more detailed picture with four-times higher density than the conventional video picture.

Accepts various input signals

This projector has a built-in high performance scan converter which converts the input signals to display the 15 k RGB, HDTV, VGA1), SVGA1), XGA1), SXGA1) and UXGA1) (fV = 60 Hz) signals as well as the video signals of the composite, S video and component.

System expandability and versatility

The projector has RS-232C/422A/PJ COM interface connectors for communication. By combining the interface boards and signal interface switcher (not supplied), VPL-FX200U/FX200E/FX200M projection systems can be greatly expanded. This projector also has the group and device index functions for using multiple projectors in one system.

panels with approximately 790,000

Easy and flexible setup

• Sony’s original APA (Auto Pixel Alignment) function

You can obtain the clearest picture automatically by simply pressing the APA key when the signal is input from a computer.

• Easy setup with external equipment

This projector has 39 preset data for input signals in the memory. You can get a picture properly on the screen by connecting equipment and pressing the APA key.

..........................................................................................................................................................................................................

1) VGA, SVGA, XGA, SXGA and UXGA are the registered trademarks of the International Business Machines Corporation, U.S.A.

6 (GB)

• Flexible setup

The lens shift function allows you to install the projector in a wide range of locations, without worrying about keystone distortion (the picture going out of square). The power focus and power zoom functions also let you change the size of the projection screen without having to move the projector.

• Stack installation

Thanks to the lens shift function, up to three projectors can be stacked, which improves the brightness of the image.

• Fail safe function

The projector uses four lamps for light source. Even if one of them has burnt out, you can still use the projector. If two lamps have burnt out, the projector will automatically enter into standby mode.

7 (GB)

Location and Function of Controls

Front

!º

379

1 Lens mount part

When attaching the optional lens, consult with the Sony service personnel.

2 Speaker

3 Front remote control (SIRCS) detector

4 Bottom ventilation holes (intake)

Do not block the holes.

5 Adjusters

Use the adjusters to keep the projector level if it is installed on an uneven surface.

6 Front ventilation holes (intake)

Do not block the holes.

7 Adjuster button and lever

Press the button to raise the lever for adjusting the height of the adjuster.

8546

8 Handle lever (left and right sides)

Use the lever for putting away the carrying handle.

9 Carrying handle (left and right sides)

Pull out the handle for carrying the projector.

!º Left and right side ventilation holes (exhaust)

Do not place anything within the 30 cm (11 range from these holes or block them.

Notes

• Do not block the ventilation holes, or internal heat build-up may occur, causing fire or damage to the projector.

• Do not place anything near the ventilation holes or touch these holes as the temperature will be very high.

/8 inches)

8 (GB)

Using the carrying handles

Pull out to use for carrying the projector. To put away the handle, slide the handle lever forward.

Using the adjusters

To lower the projector

To raise the projector

Adjuster button

1 Press the adjuster button.

The adjuster lever comes out.

2 Turn the lever to adjust the height so that the

projector becomes level.

3 Replace the adjuster lever after use.

9 (GB)

Location and Function of Controls

Control panel

123

LIGHT

5 6

VIDEO

INPUT A INPUT B INPUT C

POWER SAVING

COVER FAIL

HIGH TEMP

RESET

MUTING

PIC AUDIO

INPUT SELECT

SELECT

FAN FAIL

SYS SET

APA

VOLUME

LAMP FAIL

1 ON key and indicator

Press to turn on the power of the projector. The indicator lights when the key is pressed. The indicator flashes for about six minutes after the power is turned off by pressing the STANDBY key, as the fan runs for six minutes to cool down the inside of the projector. The indicator flashes quickly for one minute, during which you will not be able to turn the power back on with the ON key.

2 STANDBY key and indicator

Press to make the projector enter standby mode. The indicator lights to indicate that the projector is in standby mode.

3 LIGHT key

Illuminates the key indicators in orange when the projector is turned on. Illuminates the indicators for the relative keys in green when this key is pressed during operation. Press again to turn off the indicators.



STANDBY

!•

!¶ !§

!∞

ENTERRESET

!¢

–

PATTERN

ZOOM SHIFT FOCUS

!£ !™ !¡

!º

4 APA (Auto Pixel Alignment) key

Adjusts the position of the picture on the screen automatically so that the picture is clearly visible when the signals are input from a computer.

5 MUTING keys

Cut off the picture or sound temporarily.

PIC: Press to cut off the picture. Press again to

restore the picture.

AUDIO: Press to cut off the sound output from the

speakers or the AUDIO OUT jacks. Press again or press the VOLUME + key to restore the sound.

6 VOLUME +/– keys

Adjust the volume of the built-in speakers and output level of the AUDIO OUT jacks.

+ : Increases the volume. – : Decreases the volume.

Pressing this key and the RESET key simultaneously has the same function as the SYS SET key on the Remote Commander. Use when the PC-3000 signal interface switcher is used in the system or the system connections are changed.

10 (GB)

7 INPUT SELECT keys

Select the input signal.

VIDEO: Selects the video signal input from the

VIDEO or S VIDEO connectors and the audio signal input from the AUDIO IN L/R jacks. To switch the S VIDEO and VIDEO connectors, use the SELECT key.

SELECT: Each time you press this key, the input

video signal is switched between the VIDEO and S VIDEO connectors.

INPUT A: Selects the audio and video signals input

from the INPUT A connectors.

INPUT B: Selects the signal input from the

connectors on the optional interface board which is installed in the INPUT B section. When the IFB-12A interface board is installed and the output mode is selected on the IFB-12A, the key does not function.

INPUT C: Selects the signal input from the

connectors on the optional interface board which is installed in the INPUT C section.

Note on the VPL-FX200E model

The optional IFB-X2000E interface board is required to select VIDEO.

8 Indicators

POWER SAVING: Lights when the projector is in

power saving mode. When POWER SAVING in the SET SETTING menu is set to ON, the projector goes into the power saving mode if no signal is input for 10 minutes. Although the lamp goes out, the cooling fan keeps running. In the power saving mode, only the STANDBY key functions for the first 30 seconds. The power saving mode is canceled when a signal is input or any key is pressed.

COVER FAIL: Lights when the lamp cover or air

filter cover is not secured firmly.

FAN FAIL: Lights when the fan is broken. HIGH TEMP: Lights when temperature inside the

projector becomes unusually high.

LAMP FAIL: When the lamp life has reached the

end, the indicator of that lamp lights.

9 Rear remote control (SIRCS) detector

!º Message display window

Displays the signal status, timer and error messages about the input signals.

!¡ PATTERN key

Displays a HATCH pattern on the screen for focus, zoom, and shift adjustments. Press again to turn off the HATCH pattern.

!™ ZOOM key

Enters the zoom adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the zoom using the arrow keys.

V: Enlarges the picture size. v: Reduces the picture size.

Note

If the VPLL-2075, VPLL-2014 or VPLL-2009 optional lens is installed, you cannot adjust the zoom.

!£ FOCUS key

Enters the focus adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the focus using the arrow keys.

V: Focuses on a forward picture. v: Focuses on a picture further back.

!¢ SHIFT (lens shift) key

Enters the shift adjustment mode. When the key is pressed, the relative keys light in green. Next adjust the vertical position of the picture using the arrow keys.

V: Moves the picture upward. v: Moves the picture downward.

!∞ ENTER key

Stores the settings in the menu.

!§ Arrow keys (V/v/B/b)

Used to adjust the picture after pressing the ZOOM, FOCUS or SHIFT key. Also used to move the cursor or adjust the value in the menu.

!¶ MENU key

Displays the menu on the screen. When the key is pressed, the relative keys light in green. Press again to turn off the menu.

!• RESET key

Resets the adjusted value of an item to its factory preset value. This key functions when the menu or a setting item is displayed on the screen.

11 (GB)

Location and Function of Controls

Rear

6 5 4 3 12

INPUT C INPUT B

INPUT A VIDEO

R/R-Y Y

G/Y

B/B-Y

SYNC

/HD

AUDIO

RS-

RS-232C/422A RS-485IN OUT IN OUT

232C

422A

VIDEO8VIDEO

VIDEO

LRL

(MONO)

AUDIO

(MONO)

REMOTE CONTROL S TRIG

VIDEO

AUDIO OUT

OUT

PLUG IN POWER

LIGHT

MUTING

PCI AUDIO

INPUT SELECT

VIDEO

SELECT

INPUT A INPUT B INPUT C

POWER SAVING

COVER FAIL

FAN FAIL

HIGHT TEMP

789!º !¡ !™

1 Control panel

For details, see pages 10 (GB) and 11 (GB).

2 AUDIO OUT L/R jacks (phono type)

Connect to external active speakers. The volume of the speakers can be controlled by the VOLUME keys on the Remote Commander or the control panel.

3 VIDEO connectors

Connect to external video equipment, such as a VCR.

Y IN/C IN (BNC type): Connect to the Y and C

video outputs of the video equipment.

S VIDEO IN (mini DIN 4-pin): Connects to the Y/C

video output of the video equipment.

S VIDEO OUT (mini DIN 4-pin): Used as loop-

through output via the Y/C IN connectors or the S VIDEO IN connector.

VIDEO IN (BNC type): Connects to the composite

video output connector of the video equipment.

VIDEO OUT (BNC type): Used as loop-through

output of the VIDEO IN connector.

AUDIO IN L (MONO)/R jacks (phono type):

Connect to the audio output jacks of equipment, such as a VCR. For stereo equipment, use both the L and R jacks; for monaural equipment, use the L (MONO) jack only.

12 (GB)

VIDEO/ S VIDEO

LAMP FAIL

12 34

DEVICE INDEX

0 0

ENTER

FOCUSSHIFTZOOM

VOLUME

APA

RESET

PATTERN

–

Note

If you have video equipment connected to both the Y/ C IN and S VIDEO IN connectors, the signal from the Y/C IN connectors are selected prior to the S VIDEO IN connector. When projecting video connected to the S VIDEO IN connector, be sure not to connect any cable to the Y/C IN connectors.

Note on the VPL-FX200E model

The optional IFB-X2000E interface board is required for using the VIDEO connectors.

4 INPUT A connectors

RGB input connectors (R/R-Y/P

R, G/Y, B/B-Y/PB,

SYNC/HD, VD) (BNC type): Connect to the

video outputs of equipment such as a computer or a video camera. According to the connected equipment, the RGB, component (R-Y, Y, B-Y) or HDTV (YP

BPR)

signal is selected.

AUDIO IN L (MONO)/R jacks (phono type):

Connect to the audio output jacks of equipment such as a computer or a video camera. For stereo equipment, use both the L and R jacks; for monaural equipment, use the L (MONO) jack only.

Note

The INPUT A connectors do not function when the PC-3000 signal interface switcher is connected.

5 Signal interface board attachment part (INPUT B)

Optional signal interface board can be attached according to your requirements. If you install the IFB12A interface board to this section and select the output mode, you can output the signal input through the INPUT A connectors.

For details on installing the interface boards, consult with qualified Sony personnel.

6 Signal interface board attachment part (INPUT C)

Optional signal interface board can be attached according to your requirements.

9 TRIG (trigger output) jack (monaural minijack)

The signal is transmitted from this jack to the connected equipment whether the projector is on or off. (This is not a power source for external equipment.) Approximately 12 V DC signal is output when the projector power is on. The signal is 0 volt level output when the projector power is off.

!º DEVICE INDEX switch

Set the device index number of the projector when using multiple projectors. You can set the numbers between “01” and “99”. It is set to “01” at the factory. You can also set the group index number in the menu for system setup.

Note

You cannot select the output mode when attaching the IFB-12A interface board.

7 REMOTE connectors

Used to expand system capability.

RS-232C/RS-422A select switch: Selects according

to the interface connected to the RS-232C/RS422A connector.

RS-232C/RS-422A connector (D-sub 9-pin,

female): Connect to a computer to operate the

projector from the computer.

PJ COM IN/OUT connectors (D-sub 9-pin,

female): The connectors conform to the RS-485

standards and are used to expand system capability for Sony projectors.

For details on connections, see the PJ COM protocol manual for Sony projectors.

8 CONTROL S IN/OUT jacks (stereo minijack)

Connect to the control S jacks of other Sony equipment.

CONTROL S IN/PLUG IN POWER (DC 5 V

output) jack: Connects to the CONTROL S OUT

jack of the supplied Remote Commander when using as a wired Remote Commander. In this case, you do not need to install the batteries in the Remote Commander, since the power is supplied from this jack.

CONTROL S OUT jack: Outputs the control S

signal.

Note

Do not set the device index number to “00”. If you do, the projector will be operated only with the keys on the control panel.

!¡ AC IN socket

Connect the supplied AC Power cord.

!™ Lamp cover

Note

When connecting the remote commander cable to the CONTROL S IN jack, the remote control detectors will not function.

13 (GB)

Location and Function of Controls

Remote Commander

The Remote Commander can be used as a wireless or wired Remote Commander. The keys on the Remote Commander with the same names function the same as those on the control panel of the projector.

For details on control panel keys on the projector, see pages 10 (GB) and 11 (GB).

CENT

MEMORY

!º !¡

LIGHT

MUTING

PIC ONAUDIO OFF

NORMAL

APA

LCD LENS CONTROL

ZOOM

PATTERN

STATUS

RGB

DOT PHASE

SHIFT

56784

COMMAND

OFF

SIZE

SHIFT

FOCUS

!™ !£

!¢

INPUT SELECT

VIDEO

SELECT

VIDEO/S VIDEO

ADBC

SWITCHER/VIDEO MEMORY/INDEX

1423

5867

SW NO/

10/0(ALL)

OFF/GROUP

SWITCHER INDEX

SYS SET

VIDEO MEMORY

BLKG

SHARP

RESET

FUNCTION

PICTURE CONTROL

BRIGHT

HUE

!∞

!§

!¶

!•

!ª

1 ON/STANDBY keys

2 MEMORY key

The key does not function with this projector.

3 CENT R/B keys

The keys do not function with this projector.

4 COMMAND ON/OFF key

No keys except for the LIGHT button on the Remote Commander function when this switch is set to OFF. This saves battery power.

5 RGB keys

Adjust the picture.

APA: The key functions the same as the APA key on

the control panel.

CONTR

COLOR

ONSTANDBY

@∞

@¢

ENTER

POSITION

@£ @™

@¡

VOL

@º

@§

DOT PHASE: Press to adjust the phase of the LCD

panels and the input signals (except for 15k RGB/ video/HDTV signals). After pressing this key, adjust the position of the picture using the four arrow keys so that the clearest picture is obtained.

SIZE: Enters the size adjustment mode for the input

signal. Next adjust the horizontal size of the picture using the arrow keys.

B: to reduce horizontal size b: to expand horizontal size

SHIFT: Enters the shift adjustment mode for the

input signal. Next adjust the position of the picture using the four arrow keys. The picture shifts in the direction of the arrow on the pressed key.

14 (GB)

6 STATUS ON/OFF keys

Press OFF to eliminate the on-screen display. Press ON to restore the on-screen display.

Note

The menus and warning messages appear even if the OFF key is pressed.

7 Transmission indicator

The light goes on each time a key is pressed. If the indicator does not light, replace the batteries.

8 LIGHT button

Illuminates the key indicators when the COMMAND switch is set to ON. If the switch is set to OFF, only the COMMAND switch is illuminated. If you do not press any key on the Commander for more than 30 seconds, the key indicators turn off automatically. The indicators also turn off if you press the LIGHT button again.

9 MUTING keys

!º NORMAL key

The key does not function with this projector.

!¡ LCD LENS CONTROL keys

Press one of the ZOOM, SHIFT and FOCUS keys and then the arrow keys (V or v).

!™ PATTERN key

!£ SYS SET (system set) key

When the PC-3000 signal interface switcher is used in the system or the system connections are changed, press this key.

Note

After connecting the PC-3000 switcher and pressing the SYS SET key, the input channel is set to SW1-1 when connecting a single switcher, or to SW1-2 when connecting two or more switchers.

!¢ INPUT SELECT keys

The D key does not function with this projector.

!∞ SWITCHER/VIDEO MEMORY/INDEX select switch

Selects the function of the SWITCHER/VIDEO MEMORY/INDEX keys.

SWITCHER: selects the input from the PC-3000 switcher. VIDEO MEMORY: The position does not function with this projector. INDEX: selects a projector by its index number when multiple projectors are used.

!§ SWITCHER/VIDEO MEMORY/INDEX keys

When the SWITCHER/VIDEO MEMORY/ INDEX select switch is set to SWITCHER

When the PC-3000 switcher is connected to the projector, press a number key (1 to 8) to select the input from the switcher. Number key 9 does not function. To select an input when multiple switchers are connected, press the SW NO/OFF/GROUP key. Next press the switcher number (1 to 8) and the input number (1 to 8) in sequence. Be sure to press the keys one after another within 2 seconds. e.g. To select input 4 of switcher 2, press the keys as follows:

SW NO n 2 n 4.

When the SWITCHER/VIDEO MEMORY/ INDEX select switch is set to INDEX

Used to specify the device or group index number.

!¶ BLKG (blanking) adjustment key

Enters the blanking adjustment mode. Next, press V/v key to select the position to be adjusted on the screen, and then adjust the position using the B/b keys.

!• RESET key

!ª PICTURE CONTROL +/– keys

Adjust the picture conditions: CONTR (contrast), BRIGHT (brightness), COLOR, HUE and SHARP (sharpness).

@º VOL (volume) +/– keys

@¡ POSITION +/– keys

These keys do not function with this projector.

(continued)

15 (GB)

Location and Function of Controls

@™ FUNCTION key

The key does not function with this projector.

@£ ENTER key

@¢ Arrow keys

@∞ MENU key

@§ CONTROL S OUT jack

Connect the supplied remote control cable to this jack and to the CONTROL S IN jack of the projector for wired remote control operation. When the Commander is connected to the CONTROL S IN/PLUG IN POWER jack of the projector via the remote control cable (stereo), the power for the Remote Commander is supplied from the projector.

16 (GB)

Battery installation

1 Push to open the lid.

2 Install three R6 (size AA) batteries (supplied) with

the polarities correctly aligned.

Be sure to install the battery from the ’ side.

To connect the Remote Commander to the projector

Rear

INPUT C INPUT B

INPUT A VIDEO

AUDIO OUT

REMOTE CONTROL S TRIG

to CONTROL S IN

Remote commander cable (supplied)

–

DEVICE INDEX

0 0

Remote Commander

to CONTROL S OUT

3 Replace the lid.

Notes on batteries

• Make sure that the battery orientation is correct when inserting batteries.

• Do not mix old battery with new one, or different types of batteries.

• If you will not use the Remote Commander for a long time, remove the batteries to avoid damage from battery leakage. If batteries have leaked, remove them, wipe the battery compartment dry and replace the batteries with new ones.

Notes on wireless Remote Commander operation

• Be sure that there is nothing to obstruct the infrared beam between the Remote Commander and the projector.

• The operation range is limited. The shorter the distance between the Remote Commander and the projector, the wider the angle within which the commander can control the projector.

• The remote control detectors on the projector do not operate when connecting the remote commander cable to the CONTROL S IN jack. If you wish to use the Remote Commander as a wireless Remote Commander, be sure to remove the remote commander cable from both the Remote Commander and the projector.

Note on wired Remote Commander operation using the supplied remote commander cable (stereo)

You do not need to install the batteries since the power is supplied from the CONTROL S IN jack on the projector. In this case, the batteries are not consumed.

17 (GB)

Precautions on Installation

Do not install the projector in the following situations. These installations may cause malfunction or damage to the projector.

Do not install the projector in an illventilated place

The projector is equipped with ventilation holes for intake on the bottom and front and ventilation holes for exhaust on the left and right sides to prevent internal heat build-up. Do not block these ventilation holes and allow adequate air circulation at an installation location.

Do not place any object beside the projector

If you put something beside the ventilation holes on the sides, the exhaust may be inhaled into the projector through the ventilation holes (intake) at the bottom, causing the internal temperature to rise and thereby activating the protection circuit. Install the projector so that the exhaust is not blocked.

Do not install the projector in a location where temperature or humidity is very high

Avoid installing the projector in a location subject to excessive dust

Do not use the projector while laying it on its side

Do not tilt the projector when in use

20°

Avoid tilting the projector more than 20 degrees or installing it other than on the floor and ceiling. Such installations may cause malfunctions such as color irregularity or shortening of lamp life.

Do not cover the ventilation holes (exhaust)

Avoid installing the projector in a location where temperature may rise or fall rapidly

Be careful of air-conditioning and heating in a room where the projector is installed, as sudden changes in temperature may lead to moisture condensation and cause damage to the projector.

18 (GB)

Do not cover the front ventilation holes; otherwise, internal heat may build up.

Do not install the projector on a deep-pile carpet

If you install the projector on a deep-pile carpet, the ventilation holes (intake) at the bottom may be blocked, causing an internal heat build-up.

Installing the Projector on the Floor

This section describes the installation arrangements for installing the projector on the floor. For ceiling installation, consult with qualified Sony personnel.

For details on installation examples with projection distances, see the supplied “Projection Distance Charts”.

Setting up and projecting

Horizontal center of the screen

Vertical center

of the screen

Installation area

Projection distance

Install the projector so that the tip of the lens is within this area.

Adjust the vertical and horizontal positioning of the projector.

Vertical positioning (side view)

Screen

Adjustable range

U EN M

R TE N E

S CU O

T IF

SH E S

LIGHT

ING IO

MUT AUD

PATTERN

VOLUM

ECT EO

–

EO SEL VID S VID INPUT CT

T C SELE

OUT

INPU

INPUT A VIDEO

VIDEO

T B INPU

AIL A

LAMP

INPUT

-Y EO ID

R/R

G VIN

ER SA IL

POW

INPUT C INPUT B

IDE

COVER

FAN FAIL

AUDIO OUT

EMP

-Y

VID

B/B

HIGHT T

E IN IC EV D

SYNC D /H

ONO) (M

UDIO

A IN

ONO)

INO

UDIO A IN

R E

OW G IN P PLU

5 RS-48

REMOTE CONTROL STRIG

IN O

2A 2C/42

-23 S R

422A RS 232C

You can adjust the angle of projection by performing the shift adjustment (page 23 (GB)).

U EN M

R NTE E

S CU O

T IF

SE E

LIGH

M O O Z

UTING

UDIO M A

PATTERN

VOLU

–

EO VIDEO/ T SELECT S VID T INPU SELEC

OUT

INPUT C

INPUT A VIDEO

VIDEO

INPUT

AIL A

LAMP

INPUT

-Y IDEO

R/R

SAVIN

AIL

POWER

INPUT C INPUT B

EO ID

VID

G/Y

COVER

FAN FAIL

AUDIO OUT

EMP

-Y

VID

B/B

HIGHT T

E IN IC EV D

SYNC D /H

(MONO)

UDIO

A IN

(MONO)

INOU

UDIO A IN

R E

IN PO G PLU

-485 S R

REMOTE CONTROL STRIG

IN O

-232C/42 RS

S 422A R 232C

• Install the projector so that the center of the lens is between just above the bottom edge of the screen and the center of the screen.

• When using the VPLL-2009, make sure that the center of the lens is aligned with the vertical center of the screen.

Horizontal positioning (top view)

Screen

Center of the projector

The distance between the lens and the screen varies depending on the size of the screen and the attached lens. Use the charts for installation examples in the supplied “Projection Distance Charts.”

38 mm (1 1/2 inches)

Center of the lens

Adjust the horizontal positioning of the projector so that the center of the lens is aligned with the horizontal center of the screen.

19 (GB)

Connecting with a Computer or a VCR

This section describes how to connect the projector with a computer, VCR, and external active speakers.

For details on how to connect other equipment, see pages 33 (GB) to 35 (GB).

Also refer to the instruction manuals of the equipment to be connected.

When making connections, be sure to:

• turn off all equipment before making any connections.

• use the proper cables for each connection.

• insert the plugs of the cables properly; plugs that are not fully inserted often generate noise. When pulling out a cable, be sure to pull it out by the plug, not the cable itself.

Note on the VPL-FX200E model

The optional IFB-X2000E interface board is required for using the VIDEO connectors.

VCR

SMF-400 Monitor cable (5BNC˜HD D-sub 15-pin) (not supplied) Use the optional ADP-20 Signal adapter (not supplied) when connecting with a Macintosh computer.

to S VIDEO OUT

S video cable (not supplied)

Rear

INPUT C INPUT B

INPUT A VIDEO

REMOTE CONTROL S TRIG

Audio cable

(not supplied)

to VIDEO OUT

AUDIO OUT

to AUDIO OUT

Audio cable (not supplied)

–

DEVICE INDEX

Audio cable (not supplied)

Video cable (not supplied)

to AC IN

to a wall outlet

AC power cord (supplied)

20 (GB)

Active speakers

Computer

Note

Set INPUT-A in the SIGNAL SELECT menu to RGB.

For details, see page 32 (GB).

Signal flow

Projecting

STANDBY indicator

INPUT C INPUT B

INPUT A VIDEO

AUDIO OUT

REMOTE CONTROL S TRIG

DEVICE INDEX

Rear remote control detector

LIGHT

RESET

SYS SET+

–

0 0

MUTING

PIC AUDIO

INPUT SELECT

VIDEO

SELECT

INPUT A INPUT B INPUT C

LAMP FAIL

POWER SAVING

COVER FAIL

FAN FAIL

HIGHT TEMP

APA

VOLUME

PATTERN

–

ON indicator



STANDBY

ENTERRESET

ZOOM SHIFT FOCUS

1 4,5,6,7

7 4,6

5 3,8

7 5

3,8

LIGHT

MUTING

STATUS

PIC ONAUDIO OFF

RGB

NORMAL

DOT PHASE

APA

LCD LENS CONTROL

ZOOM

PATTERN

VIDEO

SWITCHER/VIDEO MEMORY /INDEX NO

SHIFT

INPUT SELECT

SELECT

VIDEO/S VIDEO

ADBC

1423

5867

SW NO/

10/0(ALL)

OFF/GBOUP

FOCUS

SYS SET

VIDEO MEMORY SWITCHERINDEX

COMMAND

OFF

CENT

SHIFT

BLKG

RESET

SHARP

MEMORY

PUNCTION

PICTURE CONTROL

BRIGHT

HUE

SIZE

CONTR

COLOR

ONSTANDBY

ENTER

POSITION

VOLUME

4,6 1

4,5,6,7

2 2

1 Press the ON key on the Remote Commander or the control panel.

The ON indicator lights in green.

2 Turn on the power of equipment connected to the projector. Press the

INPUT SELECT keys on the Remote Commander or the control panel to select the input source.

VIDEO: Selects the video signal input from the VIDEO or S VIDEO

connectors and the audio signal input from the AUDIO IN L/R jacks. To switch the VIDEO or S VIDEO connectors, use the SELECT key.

SELECT: Each time you press this key, the input signal is switched

between VIDEO and S VIDEO.

INPUT A: Selects the audio and video signals input from the INPUT

A connectors.

INPUT B: Selects the signal input from the connectors on the optional

interface board which is installed in the INPUT B section.

INPUT C: Selects the signal input from the connectors on the optional

interface board which is installed in the INPUT C section.

(continued)

21 (GB)

Projecting

When you input the signal from equipment connected to the PC-3000 signal interface switcher (not supplied), set the SWITCHER/VIDEO MEMORY/INDEX select switch on the Remote Commander to the SWITCHER position and press the number keys to select the input. When multiple switchers are connected, press the SW NO/OFF/ GROUP key, then press the number keys to select the input.

Note

Press the SYS SET key when you make the system connections using the PC-3000 switcher.

Note on the VPL-FX200E model

The optional IFB-X2000E is required for selecting VIDEO.

3 Press the PATTERN key on the Remote Commander or the control

panel to display the HATCH pattern.

4 Press the FOCUS key then the V or v key on the Remote Commander

or the control panel to adjust the focus.

“FOCUS” appears on the screen during adjustment.

5 Press the ZOOM key then the V or v key on the Remote Commander

or the control panel to adjust the picture size.

“ZOOM” appears on the screen during adjustment.

Note

If the optional VPLL-2075, VPLL-2014 or VPLL-2009 lens is installed, you cannot adjust the zoom.

6 Press the FOCUS and arrow keys on the Remote Commander or the

control panel to adjust the focus again.

“FOCUS” appears on the screen during adjustment.

22 (GB)

7 Press the SHIFT key then the arrow keys on the Remote Commander

or the control panel to adjust the vertical position of the picture.

“PICTURE SHIFT” appears on the screen during adjustment.

8 Press the PATTERN key again to clear the HATCH pattern.

To turn off the power

Adjust the volume Cut off the sound

Cut off the picture

Note

Press

the VOLUME +/– keys. the AUDIO MUTING key (also cuts off the signal output

from the AUDIO OUT jacks.) To restore the sound, press the AUDIO MUTING key again or press the VOLUME + key.

the PIC MUTING key. To restore the picture, press the PIC MUTING key again.

Do not look into the lens when the projector lamp is on.

1 Press the STANDBY key on the Remote Commander or the control

panel.

The ON indicator flashes in green and the cooling fan keeps running for about six minutes to reduce the internal heat. The ON indicator flashes quickly for one minute. During this time, you will not be able to turn the power back on. After about one minute, you can turn on the power with the ON key.

When the fan stops running, the STANDBY indicator lights in red.

Note

To extend the lamp life, do not turn off the power for at least 10 minutes after turning on the power.

23 (GB)

Using the Menu

The projector is equipped with an on-screen menu for making various adjustments and settings. Unadjustable items are not displayed in the menu.

To change the language used in the menu, see page 30 (GB).

1 Press the MENU key.

The menu display appears. The menu presently selected is highlighted in yellow.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP: COLOR SYS: AUTO DRC:

80 50 50 50 50 OFF LOW

HIGH

VIDEO

2 Use the V or v key to select a menu, then press the

b or the ENTER key.

The setting items of the selected menu are displayed.

Menus

Setting items

To erase the menu display

Press the MENU key. The menu display also disappears automatically if no key is pressed for one minute.

To reset settings that have been adjusted

Press the RESET key. “Reset complete!” appears on the screen and the settings appearing on the screen will be reset to their factory preset values.

Items that can be reset are as follows:

CONTRAST, BRIGHT, COLOR, HUE, SHARP, DOT PHASE, SIZE, SHIFT and BLANKING.

About the memory of the settings

The settings are automatically stored in the projector memory.

SET SETTING

STATUS: SPEAKER: LANGUAGE: INSTALLATION: POWER SAVING SIRCS RECEIVER GROUP INDEX: DEVICE INDEX:0101

ON ON ENGLISH FLOOR-FRONT OFF

FRONT&REAR

INPUT-A

3 Make setting or adjustment on an item.

For details on setting individual items, see the relevant menu pages.

24 (GB)

The PICTURE CTRL Menu

Adjustments and settings using the menu

The PICTURE CTRL menu is used for adjusting the picture. Unadjustable items are not displayed in the menu.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP: COLOR SYS: AUTO DRC:

80 50 50 50 50 OFF LOW

HIGH

VIDEO

Operation

1. Select an item

Use the V or v key to select the item, then press the b or the ENTER key.

2. Adjust an item

• When changing the adjustment level:

To increase the number, press the V or b key. To decrease the number, press the v or B key. Press the ENTER key to restore the original screen.

COLOR

Adjusts color intensity.

COLOR: 50

The higher the setting, the greater the intensity. The lower the setting, the lower the intensity.

HUE

Adjusts skin tones.

HUE: 50

At high settings, the picture becomes greenish. At low settings, the picture becomes purplish.

• When changing the setting:

Press the V or v key to change the setting, then press the B or the ENTER key. The original screen is restored.

CONTRAST

Adjusts the picture contrast.

CONTRAST: 80

The higher the setting, the greater the contrast. The lower the setting, the lower the contrast.

BRIGHT (Brightness)

Adjusts the picture brightness.

SHARP (Sharpness)

Adjusts the picture sharpness.

SHARP: 80

The higher the setting, the sharper the picture. The lower the setting, the softer the picture.

D. (Dynamic) PICTURE

Emphasizes the black color.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP:

D.PICTURE:

COLOR TEMP: COLOR SYS: AUTO DRC:

80 50 50 50 50 OFF

OFF ON

HIGH

VIDEO

BRIGHT: 80

The higher the setting, the brighter the picture. The lower the setting, the darker the picture.

ON: Emphasizes the black color to produce a bolder

“dynamic” picture.

OFF: Reproduces the dark portions of the picture

accurately, in accordance with the source signal.

25 (GB)

The PICTURE CTRL Menu

COLOR TEMP (temperature)

Adjusts the color temperature.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE:

COLOR TEMP:

COLOR SYS: AUTO DRC:

80 50 50 50 50 OFF HIGH

HIGH LOW HIGH

VIDEO

HIGH: Makes the white color bluish. LOW: Makes the white color reddish.

COLOR SYS (system)

Selects the color system of the input signal.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP:

COLOR SYS:

DRC:

80 50 50 50

AUTO NTSC3.58

50 PAL

OFF SECAM

HIGH AUTO

NTSC4.43 HIGH

PAL-M

VIDEO

Normally, set to AUTO. If the picture is distorted or colorless, select the color system (NTSC3.58/PAL/SECAM/NTSC4.43/PAL-M) according to the input signal.

GAMMA MODE

Select either position to obtain an optimum picture.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR TEMP:

GAMMA MODE:GRAPHICS

80 50 HIGH GRAPHICS TEXT

INPUT-A

DRC (Digital Reality Creation)

Selects the level of DRC effects.

PICTURE CTRL

CONTRAST: BRIGHT: COLOR: HUE: SHARP: D.PICTURE: COLOR TEMP: COLOR SYS: AUTO

DRC:

80 50 50 50 50 OFF LOW

HIGH LOW

HIGH

VIDEO

HIGH: Increases the DRC effects. LOW: Decreases the DRC effects.

Input signals and adjustable/setting items

Input signal

Item

CONTRAST BRIGHT COLOR HUE

Video

S video

Y Y Y Y

15k

RGB

Y Y N N

Compo-

nent

(NTSC

3.58/

4.43 only)

SHARP D. PICTURE COLOR

Y Y Y

N N Y

TEMP COLOR

SYS GAMMA

MODE DRC

Y: Adjustable/can be set N: Not adjustable/cannot be set

RGB

(preset)

Y Y Y N

Y Y Y

RGB (preset) (HDTV-

Y Y N N

N N Y

BPR)

Y Y Y Y

Y N Y

RGB

(not

preset)

Y Y N N

N N Y

GRAPHICS: Improves the reproduction of half

tones. Photos can be reproduced in natural tones.

TEXT: Contrasts black and white. Suitable for

images with lots of text.

1) NTSC4.43 is the color system used when playing back a video recorded in NTSC color system on a NTSC4.43 system VCR.

26 (GB)

The INPUT SETTING Menu

The INPUT SETTING menu is used to change the settings of the input signal. Unadjustable items, which vary according to the input signal, are not displayed in the menu.

INPUT SETTING

DOT PHASE: SIZE SHIFT

8 H:1344 H:123 V:123

INPUT-A

1024x768 NO . 2 3 n

Operation

1. Select an item

Use the V or v key to select the item, then press the b or the ENTER key.

2. Adjust an item

• When changing the adjustment level:

To increase the number, press the V or b key. To decrease the number, press the v or B key. Press the ENTER key to restore the original screen.

• When changing the setting:

Press the V or v key to change the setting, then press the B or the ENTER key. The original screen is restored.

DOT PHASE

Adjusts the phase of the LCD panel and the input signal when H FILTER is set to OFF. Adjust the value to obtain the clearest picture.

As the setting for H increases, the horizontal size of the picture becomes larger, and as the setting decreases, the size becomes smaller. Adjust the setting according to the input signal. Use the B or b key to adjust the horizontal size.

SHIFT

Adjusts the position of the picture.

H:123 V:123

SHIFT

H adjusts the horizontal position of the picture, and V adjusts the vertical position. As the setting for H increases, the picture moves to the right, and as the setting decreases, it moves to the left. As the setting for V increases, the picture moves up, and as the setting decreases, it moves down. Use the B or b key to adjust the horizontal position and the V or v key for the vertical position.

SCAN CONV (converter)

Converts the signal to display the picture so that it fits the screen size.

INPUT SETTING

DOT PHASE: SIZE SHIFT

SCAN CONV: ON

8 H:1056 H:123 V:123 ON OFF

INPUT-A

800x600 NO . 1 7 n

DOT PHASE: 8

SIZE

Adjusts the horizontal size of the picture.

SIZE

H:1344

ON: Displays the picture according to the screen

size. The picture will lose some clarity.

OFF: Displays the picture while matching one pixel

of input picture element to that of the LCD. The picture will be clear but the picture size will be smaller.

27 (GB)

The INPUT SETTING Menu

ASPECT

Sets the aspect ratio of the picture. When inputting 16:9 (squeezed) signal from equipment such as a DVD player, set to 16:9.

INPUT SETTING

SHIFT

ASPECT: 4:3

BLANKING TOP

H:123 V:123

4:3 16:9

VIDEO

VIDEO/60 NO . 1 n

4:3: When the picture with ratio 4:3 is input. 16:9: When the picture with ratio 16:9 (squeezed) is

input.

H FILTER

Corrects the vertical bands that appear on the picture.

INPUT SETTING

DOT PHASE: SIZE SHIFT SCAN CONV:

H FILTER: OFF

8 H:1266 H:123 V:123 ON OFF ON

INPUT-A

1280x1024

NO . 3 7 n

The vertical bands may occur when an RGB signal with horizontal resolution of more than 1024 × 768 pixels is input. In such cases, set to ON. The picture will loose some clarity, but the vertical bands will be reduced. Set to OFF to associate a dot of the input signal with a pixel of the LCD.

BLANKING

Adjusts if excess signals are seen with the picture, or the whole picture is not seen clearly.

INPUT SETTING

DOT PHASE: SIZE SHIFT SCAN CONV:

BLANKING

8 H:1056 H:123 V:123 ON

INPUT-A

800×600

NO . n

Select BLANKING, then press the ENTER key to display the blanking adjustment screen.

BLANKING

TOP: BOTTOM: 2 3 4 RIGHT: LEFT:

126

57 34

Use the V or v key to select the part to be adjusted, and the B or b key to adjust.

Input signals and adjustable/setting items

Item

Video or

S video

DOT PHASE

SIZE SHIFT SCAN CONV

ASPECT H FILTER

BLANKING

N Y N

Y N

Y (TOP and BOTTOM

BOTTOM

only)

Y: Adjustable/can be set N: Not adjustable/cannot be set

15k

RGB

N Y N

Y N

(TOP

and

only)

Input signal

Compo-

nent

N Y N

Y N

(TOP and

BOTTOM

only)

RGB

(preset)

(except

for

HDTV)

Y Y Y

(Only for

lower

resolution

than

SVGA)

N Y

(Higher

resolution

than

XGA)

(HDTV-

GBR,

HDTV-

BPR

only)

RGB

(not preset)

Y Y Y

N Y

(Higher

resolution

than XGA)

28 (GB)

INPUT MEMORY No.

The upper number indicates the memory number of the current input signal. The lower number indicates the user memory number.

INPUT SETTING

DOT PHASE: SIZE SHIFT

8 H:1048 H:123 V:123

About the memory function

The adjustment data for 39 types of input signals are preset at the factory (preset memory). When a signal is input to the projector, the signal type is automatimally detected and the data for the signal is called from the memory to display an optimum picture. The data can be adjusted in the INPUT SETTING menu and the adjusted data will be saved as user memory. When you save more than 200 user memories, the newest one always overwrites the oldest one. The saved user memory number is displayed in the INPUT SETTING menu as n NO. ππ. When an RGB signal other than the preset signals is input to the projector, the memory number is displayed as 0 and the closest option is automatically selected from the preset 39 types of signals.

Notes

• When an RGB signal is input with sync on Green including external sync, the picture tone may be greenish. In this case, disconnect the external sync signal.

• When an HDTV 1035/60i (BTA S-001B) signal is input, the picture will appear widened. Adjust SIZE, SHIFT and BLANKING referring to the following levels as a standard.

SIZE H: 1184 SHIFT H: 360

BLANKING TOP: 108

INPUT-A

1024x768 NO . 23 n

V: 34

BOTTOM: 108 RIGHT: 22 LEFT: 22

Type of input signal

Memory number

User memory number

Memory

Preset signal

No.

Video 60 Hz

Video 50 Hz

15k RGB (60 Hz) 15k RGB (50 Hz)

HDTV

640 × 350 VGA-1 (VGA350)

6 7

640 × 400 NEC PC98

8 9

640 × 480 VGA VESA60

11 12 13 14

800 × 600 SVGA VESA 56

17 18 19

20 21

832 × 624 Mac 16

1024 × 768 XGA VESA 43

23 24 25 26 27

1152 × 864 VESA 70

28 29 30

1152 × 900 SUN LO

31 32

1280 × 960 VESA 60

33 34

1280 × 1024

35 36 37 38

1600 × 1200

VESA* 85(VGA350)

VGA-2 (TEXT) /VESA70

VESA 85 (VGA400)

Mac 13 VGA VESA 72 VGA VESA 75

(IBM M3) VGA VESA 85

(IBM M4)

SVGA VESA 60 SVGA VESA 72 SVGA VESA 75

(IBM M5) SVGA VESA 85

(8514) XGA VESA 60 XGA VESA 70 XGA VESA 75 XGA VESA 85

VESA 75 VESA 85

SUN HI

VESA 75 SXGA VESA 43 SGI-5 SXGA VESA 60 SXGA VESA 75 SXGA VESA 85 UXGA VESA 60

fH (kHz)

15.73

15.63

15.73

15.63

33.75

31.47

37.86

24.82

31.47

37.86

31.47

35.00

37.86

37.50

43.27

35.16

37.88

48.08

46.88

53.67

49.72

35.52

48.36

56.48

60.02

68.68

64.00

67.50

77.49

61.80

71.71

60.00

75.00

46.43

53.32

63.97

79.98

91.15

75.00

fV (Hz)

59.94

50.00

59.94

50.00

60.00

70.09

85.08

54.42

70.09

85.08

59.94

66.67

72.81

75.00

85.01

56.25

60.32

72.19

75.00

85.06

74.55

86.96

60.00

69.96

75.03

85.00

70.02

75.00

85.06

65.96

76.05

60.00

75.00

86.87

50.06

60.01

75.03

85.02

60.00

Sync

S on G S on G S on Y/G H-pos V-neg H-pos V-neg H-neg V-neg H-neg V-pos

H-neg V-pos H-neg V-neg S on G H-neg V-neg H-neg V-neg

H-neg V-neg

H-pos V-pos H-pos V-pos H-pos V-pos H-pos V-pos

H-pos V-pos H-neg V-neg

H-pos V-pos

H-neg V-neg H-neg V-neg H-pos V-pos H-pos V-pos H-pos V-pos H-pos V-pos H-pos V-pos H-neg V-neg C-neg H-pos V-pos H-pos V-pos H-pos V-pos S on G H-pos V-pos H-pos V-pos H-pos V-pos H-pos V-pos

Horizontal size

— —

— — — —

1235

800 832 848 800

832 800

— 832 840

832

1024 1056 1040 1056

1048 1152 1264

1344 1328 1312 1376

1308 1422 1394 1283 1256 1440 1382 1272 1260 1272 1266 1296 1352

* VESA is a registered trademark of Video Electronics

Standard Association.

29 (GB)

The SET SETTING Menu

The SET SETTING menu is used for changing the initial settings of the projector. Unadjustable items are not displayed in the menu.

SET SETTING

STATUS:AT SPEAKER: LANGUAGE: INSTALLATION: POWER SAVING SIRCS RECEIVER GROUP INDEX: DEVICE INDEX:

ON ON ENGLISH FLOOR-FRONT OFF

: :

FRONT&REAR 01 01

INPUT-A

Operation

1. Select an item

Use the V or v key to select the item, then press the b key or the ENTER key.

2. Adjust an item

• When changing the adjustment level:

To increase the number, press the V or b key. To decrease the number, press the v or B key. Press the ENTER key to restore the original screen.

• When changing the setting:

Press the V or v key to change the setting, then press the B or the ENTER key. The original screen is restored.

STATUS

SPEAKER

Set to OFF to cut off the sound of the internal speaker when external speakers are connected. When set to OFF, “SPEAKER OFF” appears on the screen when you turn on the power.

SET SETTING

STATUS:

SPEAKER:

LANGUAGE: INSTALLATION: POWER SAVING SIRCS RECEIVER GROUP INDEX: DEVICE INDEX:

ON ON

ON ENGLISH

OFF FLOOR-FRONT OFF

FRONT&REAR

01 01

INPUT-A

LANGUAGE

Selects the language used in the menu and on-screen displays.

SET SETTING

STATUS: SPEAKER:

LANGUAGE:

INSTALLATION POWER SAVING SIRCS RECEIVER: GROUP INDEX: DEVICE INDEX:

ON ON

ENGLISH

FLOOR-FRONT

FRANCAIS CEILING-FRONT

DEUTSCH

: OFF

ITALIANO

FRONT&REAR

ESPANOL

01 01

Available languages are: English, French, German, Italian, Spanish, Japanese and Chinese.

INPUT-A

Sets up the on-screen display.

SET SETTING

STATUS:

SPEAKER: LANGUAGE: INSTALLATION: POWER SAVING SIRCS RECEIVER GROUP INDEX: DEVICE INDEX:0101

ON OFF

ON ENGLISH FLOOR-FRONT OFF

FRONT&REAR

INPUT-A

ON: Shows all of the on-screen displays. OFF: Turns off the on-screen displays except for the

menus and warning messages.

30 (GB)

INSTALLATION

Reverses the picture horizontally or vertically.

SET SETTING

STATUS: SPEAKER: LANGUAGE:

INSTALLATION:

POWER SAVING: SIRCS RECEIVER GROUP INDEX: DEVICE INDEX:

ON ON ENGLISH

FLOOR-FRONT

CEILING-FRONT

FRONT&REAR

FLOOR-REAR CEILING-REAR

FLOOR-FRONT: The picture is not reversed. CEILING-FRONT: The picture is reversed

horizontally and vertically.

FLOOR-REAR:

The picture is reversed horizontally.

CEILING-REAR: The picture is reversed

vertically.

Note

In case of using a mirror, be careful of installation since the picture may be reversed.

INPUT-A

OFF

+ 110 hidden pages