Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
SPECIFICATIONS
US Model
Canadian Model
STR-DE595
AEP Model
UK Model
E Model
Australian Model
Korean Model
STR-DE495/DE595
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
40 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.09 % total harmonic distortion from 250
milliwatts to rated output (STR-DE595 area
code US only).
Amplifier section
POWER OUTPUT
Models of area code US, CND
Rated Power Output at Stereo Mode
(8 ohms 40 Hz – 20 kHz, THD 0.09 %)
STR-DE595:90 W + 90 W
STR-DE495:70 W + 70 W
Models of other area code
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %)
STR-DE595:100 W + 100 W
STR-DE495:80 W + 80 W
Reference Power Output
(8 ohms 1 kHz, THD 10 %)
STR-DE595:FRONT
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down PRESET TUNING + and
press ?/1 . All preset stations will be erased when
you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs
Video:1 Vp-p, 75 ohms
Component Video (STR-DE595 only, except for
models of area code AEP, UK):
Y:1 Vp-p, 75 ohms
PB/B-Y:0.7 Vp-p, 75 ohms
PR/R-Y:0.7 Vp-p, 75 ohms
Outputs
Video:1 Vp-p, 75 ohms
Component Video (STR-DE595 only, except for
models of area code AEP, UK):
Y:1 Vp-p, 75 ohms
PB/B-Y:0.7 Vp-p, 75 ohms
PR/R-Y:0.7 Vp-p, 75 ohms
General
Power requirements
Area codePower requirements
US, CND, MX120 V AC, 60 Hz
AEP, UK230 V AC, 50/60 Hz
SP, MY, KR, AR220 – 230 V AC, 50/60 Hz
E2120/220/240 V AC, 50/60 Hz
TW110 V AC, 50/60 Hz
AUS240 V AC, 50Hz
Power consumption
Area codePower consumption
US, MXSTR-DE595: 210 W
CNDSTR-DE595: 310 VA
AEP, UK, TW, KRSTR-DE595: 210 W
STR-DE495: 180 W
SP, MYSTR-DE595: 180 W
AUS, E2, ARSTR-DE595: 210 W
Power consumption (during standby mode)
0.3 W
Dimensions430 × 145 × 298 mm
(16 7/8× 5 6/8× 11 6/8 in.)
including projecting parts
and controls
Mass (Approx.)STR-DE595: 7.5 kg (16 lb 9 oz)
STR-DE495: 7.2 kg (15 lb 14 oz)
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-U306A (1)
R6 (size-AA) batteries (2)
Design and specifications are subject to change
without notice.
•Abbreviation
CND : Canadian model
AUS: Australian model
MX : Mexican model
SP: Singapore model
E2: AC 120 V area in E model
AR: Argentine model
KR: Korean model
TW : Taiwan model
2
Page 3
STR-DE495/DE595
Ver 1.1
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakag e from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
Page 4
STR-DE495/DE595
TABLE OF CONTENTS
1. GENERAL
Main unit ................................................................................. 5
6. ELECTRICAL PARTS LIST ........................................ 40
4
Page 5
SECTION 1
GENERAL
STR-DE495/DE595
This section is extracted
from instruction manual.
5
Page 6
STR-DE495/DE595
6
Page 7
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1.CASE
(Page 7)
STR-DE495/DE595
2-2.FRONT PANEL SECTION
(Page 8)
2-5.STANDBY BOARD
(Page 9)
2-3.BACK PANEL
(Page 8)
2-4.DIGITAL BOARD
(Page 9)
2-6.MAIN BOARD
(Page 10)
Note : Follow the disassembly procedure in the numerical order given.
2-1. CASE
1
two screws
(case 3 TP2)
2
three screws
(case 3 TP2)
3
two screws
(case 3 TP2)
4
case
7
Page 8
STR-DE495/DE595
)
2-2. FRONT P ANEL SECTION
2
CNP791
3
two screws
(BVTP3 x 8)
5
front panel section
2-3. BACK P ANEL
4
CNP901
5
CN908
6
CN906
4
0
screw
(BVTP3 x 8)
1
five screws
(BVTP3 x 8)
CNS4
9
six screws
(BVTP3 x 8)
9
three screws
(BVTP3 x 8)
2
CNS8
7
three screws
(BVTP3 x 8)
8
five screws
(BVTP3 x 8)
qa
screw
(BVTP3 x 8
1
CNS7
qs
back panel
3
CNP156
8
Page 9
2-4. DIGITAL BOARD
)
8
screw (BVTP3 x 8)
3
CNP5
2
STR-DE495/DE595
7
DIGITAL board
CNP6
6
CNS2
5
CNS1
9
bracket (digital)
Ver 1.1
2-5. STANDBY BOARD
3
CNP903
4
three screws
(BVTP3 x 6)
2
CNP902
5
STANDBY board
1
CNP905
1
CNS4
4
screw (BVTP3 x 8
9
Page 10
STR-DE495/DE595
Ver 1.1
2-6. MAIN BOARD
5
screw
(BVTP3 x 6)
3
two screws
(BVTP3 x 6)
1
CNP801
2
CNP802
4
two screws
(BVTP3 x 6)
6
two screws
(BVTP3 x 6)
7
MAIN board
10
Page 11
SECTION 3
TEST MODE
STR-DE495/DE595
FACTORY PRESET MODE
* All preset contents are reset to the default setting.
* Procedure:
While depressing the [FM MODE] and the [PRESET TUNING --]
buttons simultaneously, press the
?/1 button to turn on the
main power.
The message “FA CT OR Y” appears for a moment and the present
contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE (US, Canadian, E model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Press the [TUNER FM/AM] button to set AM and press the ?/1
button to turn off the main power.
While depressing the [TUNING +] button or the
[PRESET TUNING +] button, press the ?/1 button to turn on the
main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
SPEAKER SIZE SELECTION MODE
* Either the normal speaker or micro satellite speaker can be se-
lected.
* Procedure:
While depressing the [MAIN MENU] button, press the ?/1 button to turn on the main power.
Either the message “NORM. SP .” or “MICRO SP.” appears for a
moment and select the desired speaker size.
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
* Procedure:
While depressing the [FM MODE] and the [MD/TAPE] buttons
simultaneously, press the ?/1 button to turn on the main power .
1. ALL segments light on.
4. Press the [VIDEO 1] button, all segments and all LEDs light on.
5. Every pressing the [VIDEO 1] button turns on each segment and
LED one after another in the same order.
(Not only the [VIDEO 1] button, b ut also the other b uttons such
as [VIDEO 2], [DVD], [MD/TAPE], [CD] and [TUNER FM/AM] can
be used.)
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activa ted.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn
on the main power.
The message “SF. CLR.” appears for a moment and initialization is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
While depressing the [FM MODE] and the [DVD] buttons simultaneously, press the ?/1 button to turn on the main power.
The model name, destination and the software version are displayed for a moment.
KEY CHECK MODE
* Button check
* Procedure:
While depressing the [MUSIC] and the [TUNING --] buttons simultaneously, press the ?/1 button to turn on the main power.
Either the message “REST 26” (STR-DE495) or “REST 27”
(STR-DE595) appears.
Every pressing of any button other than the
the buttons. The buttons which are already counted once are not
counted again. When all buttons are pr essed “REST 00” appears.
When [MASTER VOLUME] control is rotated in clockwise direction, “VOL MIN”, “VOL 1” to “VOL 73”, “VOL MAX” appears for a moment.
?/1 counts down
D
D
EXPROLOGICII DTS-ES NEO:6 MPEG-2 AAC
D
D
DIGITALMEMORY
L F E
SP B
OPT
COAX
MULTI CH IN 12 D.RANGE EQSTEREOMONORDS
SPSP A
LSLCR
SW
SSB SR
[2CH], [SURROUND], [MOVIE] and [MUSIC] LED light on.
2. Press the [VIDEO 1] button, confirm display.
COAX
EX
SP B
SP A
L
R
SL
SR
-ES NEO:6-2
II
1 D.RANGE EQMONO
[2CH] and [MOVIE] LED light on.
3. Press the [VIDEO 1] button, confirm display.
D
D
PROLOGIC DTSMPEG AAC
MULTI CH IN2STEREORDS
SW
SP
SSB
C
L F E
OPT
D
D
DIGITAL
[SURROUND] and [MUSIC] LED light on.
dB
kHz
mft.
MHz
dB
k
m
MHz
SLEEP
MEMORY
* When this mode is used, the receiver scans the broadcasts that
can be received by the tuner, and sets up the broadcasts.
Be sure to start scanning after connecting the antenna.
* Procedure:
Check that the antenna is connected.
While depressing the [MEMORY] button, press the ?/1 button
to turn on the main power.
The message “AUTO-BETICAL SELECT” appears for a moment and the receiver starts scanning.
COMMAND MODE SELECTION MODE
AUTOBETICAL MODE (AEP, UK model only)
Hz
ft.
SLEEP
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [ENTER] button, press the ?/1 button to
turn on the main power.
Either the message “C.MODE.AV 1” or “C.MODE.AV 2” appears for a moment and select the desired mode.
11
Page 12
STR-DE495/DE595
SECTION 4
DIAGRAMS
4-1. IC PIN DESCRIPTIONS
• IC1201 CXD9617R (DSP) (DIGITAL Board (1/2))
Pin No.Pin NameI/OPin Description
1VSS—Ground
2XRSTIReset signal input from SYSTEM CONTROL IC
3EXTININot used (Connect to ground)
4FS2INot used (Connect to ground)
5VDDIIPower supply pin (+2.6 V)
6FS1INot used (Connect to ground)
7PLOCKONot used (Open)
8VSS—Ground
9MCLK1IClock signal input (13.59 MHz)
10VDDIIPower supply pin (+2.6 V)
11VSS—Ground
12MCLK2OClock signal output (13.59 MHz)
13MSINot used (Connect to ground)
14SCKOUTOInternal system clock signal output for CODEC IC
15LRCKI1INot used (Open)
16VDDEIPower supply pin (+3.3 V)
17BCKI1INot used (Open)
18SDI1IAudio IF data input from CODEC IC
19LRCKOOSampling clock signal output for CODEC IC
20BCKOOBit clock signal output for CODEC IC
21VSS—Ground
22KFSIOI/OAudio clock signal (384fs/256fs) input/output for DIR IC
23 to 25SDO1 to SDO3ODigital audio serial data output for CODEC IC
26SDO4ONot used (Open)
27SPDIFONot used (Open)
28LRCKI2ISampling clock signal input from DIR IC
29BCKI2IBit clock signal input from DIR IC
30SDI2IDigital audio serial data input from DIR IC
31VSS—Ground
32HACNOAcknowledge signal output for SYSTEM CONTROL IC
33HDINISerial data input from SYSTEM CONTROL IC
34HCLKIClock signal input from SYSTEM CONTROL IC
35HDOUTOSerial data output for SYSTEM CONTROL IC
36HCSIChip select signal input from SYSTEM CONTROL IC
37SDCLKONot used (Open)
38CLKENONot used (Open)
39RASONot used (Open)
40VDDIIPower supply pin (+2.6 V)
41VSS—Ground
42CASONot used (Open)
43DQM/OE0ONot used (Open)
44CS0OExternal memory chip select signal output for D/A converter IC (SRAM)
45WE0OSRAM write enable signal output for D/A converter IC
46VDDEIPower supply pin (+3.3 V)
47WMD1INot used (Fixed at H)
48VSS—Ground
49WMD0INot used (Fixed at H)
50PAGE2ONot used (Open)
51VSS—Ground
52, 53PAGE1, PAGE0ONot used (Open)
54BOOTINot used (Connect to ground)
12
Page 13
STR-DE495/DE595
Pin No.Pin NameI/OPin Description
55BTACTONot used (Open)
56BSTIBoot stop signal input from SYSTEM CONTROL IC
57MOD1IOperation mode signal input (L: 386fs, H: 256fs) (Fixed at H)
58MOD0IOperation mode signal input (L: single chip mode, H: use prohibited) (Fixed at L)
59EXLOCKIError detection signal input from DIR IC
60VDDIIPower supply pin (+2.6 V)
61VSS—Ground
62, 63A17, A16ONot used (Open)
64 to 66A15 to A13OExternal memory address signal output for D/A converter IC (SRAM)
67GP10OConnect to LRCKO
68GP9ODecode signal output for SYSTEM CONTROL IC
69GP8IAudio signal input from DIR IC
70VDDIIPower supply pin (+2.6 V)
71VSS—Ground
72 to 75D15/GP7 to D12/GP4I/OExternal memory data input/output for D/A converter IC (general port)
76VDDEIPower supply pin (+3.3 V)
77 to 80D11/GP3 to D8/GP0I/OExternal memory data input/output for D/A converter IC (general port)
81VSS—Ground
82A9OExternal memory address signal output for D/A converter IC (SRAM)
83 to 85A12 to A10OExternal memory address signal output for D/A converter IC (SRAM)
86TDOONot used (Open)
87TMSINot used (Open)
88XTRSTINot used (Open)
89TCKINot used (Open)
90TDIINot used (Open)
91VSS—Ground
92 to 97A8 to A3OExternal memory address signal output for D/A converter IC (SRAM)
98, 99D7, D6I/OExternal memory data input/output for D/A converter IC (SRAM)
100VDDIIPower supply pin (+2.6 V)
101VSS—Ground
102 to 105D5 to D2I/OExternal memory data input/output for D/A converter IC (SRAM)
106VDDEIPower supply pin (+3.3 V)
107, 108D1, D0I/OExternal memory data input/output for D/A converter IC (SRAM)
109, 110A2, A1OExternal memory address signal output for D/A converter IC (SRAM)
111VSS—Ground
112A0OExternal memory address signal output for D/A converter IC (SRAM)
113PMIPLL initialization signal input from SYSTEM CONTROL IC
114, 115SDI3, SDI4INot used (Open)
116SYNCISync/async select signal input (L: sync, H: async) (Fixed at H)
1DATAOISerial data line signal input from DIR IC
2GP9IGP9 signal input from DSP IC
3BSTOBoot stop control signal output for DSP IC
4HCSOChip select signal output for DSP IC
5HACNIAcknowledge signal input from DSP IC
6XRSTOReset signal output for DSP IC
7PMOPLL control signal output for DSP IC
8PDOPower down signal output for CODEC IC
9SMUTEOSoft mute signal output for CODEC IC
10CDT1OControl data output for CODEC IC
11VSS—Ground
12SCLOSerial data clock signal output for CODEC IC
13CSOLatch signal output for CODEC IC
14DATAOSerial data output for VOL/TUNER IC
15CLKOClock signal output for VOL/TUNER IC
16LATCH– VOL ICOLatch signal output for VOL/TUNER IC
17SPK B RELAYOSpeaker B relay driver control signal output (STR-DE595 only)
18HDOUTISerial data input from DSP IC
19HDINOSerial data output for DSP IC
20HCLKOSerial data clock signal output for DSP IC
21F.MUTEOFunction mute control signal output
22AC MUTEOPower amplifier mute control signal output
23VCC5—Power supply pin (+3.3 V)
24ANA/DIGOMuting and error port signal output
25HP DETECTIHeadphone detection signal input
26NC—Not used (Fixed at L)
27FLASH2—Flash programming signal output 2
28FLASH1—Flash programming signal output 1
29 to 32NC—Not used (Fixed at L)
33SCLOClock signal output for EEPROM IC
34SDAI/OSerial data input/output for EEPROM IC
35AVCC—Power supply pin (+3.3 V)
36AVRH—Power supply pin (+3.3 V)
37AVSS—Ground
38 to 41A/D0 to A/D3IKey signal input (A/D port)
42VSS—Ground
43RDS SIGNALIRDS signal level input (AEP, UK model only)
47NC—Not used (Fixed at L)
48STOPIAC off detection signal input
49MOD0—Selection of micon operation mode
50MOD1—Not used (Connect to AVCC)
51MOD2—Selection of micon operation mode
52RDS CLOCKIRDS data clock signal input (AEP, UK model only)
53RDS DATAIRDS data input (AEP, UK model only)
54SIRCSISIRCS signal input
55FUSE DETECTIFuse open detection signal input
56POWER KEYIPower key detection signal input
Model detection signal input (Fixed at L: US, Canadian model, H: Except for US,
Canadian model)
Destination detection signal input (Fixed at L: US, Canadian model, H: Except for US,
Canadian model)
14
Page 15
STR-DE495/DE595
d
Pin No.Pin NameI/OPin Description
57, 58NCINot used (Fixed at L)
59VOL (B)IVolume encoder signal input
60VOL (A)IVolume encoder signal input
61DINOSerial data output for FL driver IC
62CLKOClock signal output for FL driver IC
63FL_STBOLatch signal output for FL driver IC
64NC—Not used (Fixed at L)
65POWER RELAYOPower relay driver control signal output
66PROTECTOROProtector detection signal output
67HEADPHONE RELAYOHeadphone relay driver control signal output
68WOOFER RELAYOSub woofer relay driver control signal output
69REAR RELAYOSurround speaker relay driver control signal output
70CENTER RELAYOCenter speaker relay driver control signal output
71PREOUT/FRONT RELAYOSpeaker A relay driver control signal output
72R1 RELAYOBridgeable relay driver control output (STR-DE595 only)
73TUNEDITuned signal detection input
74STEREOIStereo signal detection input
75MUTEOTuner mute signal output
76DOITuner serial data input
77RSTXIReset signal input
78SLATCHOTuner latch signal output
79X0A—Not used (Open)
80X1A—Not used (Connect to VSS)
81VSS—Ground
82X0—Clock signal input (16 MHz)
83X1—Clock signal output (16 MHz)
84VCC3—Power supply pin (+3.3 V)
85, 86NC—Not used (Fixed at L)
87 to 90SW4 to SW1OVideo select signal output
91, 92NC—Not used (Fixed at L)
93XMODEOXmode signal output for DIR IC
94CKSEL1OClock select signal output for DIR IC
95CLKOData clock signal output for DIR IC
96CEOLatch signal output for DIR IC
97DIOData output for DIR IC
98DOIData input from DIR IC
99ERRORIError detection signal input from DIR IC
100XSTATEIXstate signal input from DIR IC
4-2. CIRCUIT BOARDS LOCA TION
STANDBY board
POWER board
HEADPHONE board
DISPLAY board
BRIDGEABLE board
(STR-DE595 only)
VIDEO board
DIGITAL boar
MAIN board
VOL board
1515
Page 16
STR-DE495/DE595
4-3. BLOCK DIAGRAM — TUNER/AUDIO SECTION —
FM 75Ω
COAXIAL
ANTENNA
AM
TM301
FM/AM TUNER UNIT
ST-DO/MC-DI
ST-DI/MC-DO
FM SIGNAL OUT
RDS DATA
AEP,UK MODEL
SYSTEM
CONTROL
IC1601 (1/4)
RDS SIGNAL
RDS DATA
RDS CLOCK
+10V
L CH
R CH
STEREO
TUNED
MUTE
CLK
RDS INT
DIR
FUNCTION
SELECT
TU+10V
INL1
4
INL2
80
78
76
74
72
70
68
65
11
10
2
8
7
INL3
INL4
INL5
INL6
INL7
INL8
INL9
INL10
LIN1
SLIN1
SW IN1
C IN1
R-CH
DE595
(DE495)
CD/SACD
(DE595)
MD/TAPE
DVD
VIDEO 2
VIDEO 1
MULTI
CH IN
CD
IN
AUDIO
IN
AUDIO
AUDIO
FRONT
SURROUND
WOOFER
CENTER
STEREO
TUNED
MUTE
CE
FM OUT
RDS DATA
RDS INT
TU+3.3V
43
53
52
FM OUT
RDS DATA
RDS INT
DO/DI
DATA
CLK
CE
IN
IN
IN
-6
SUB
-5
J402 (1/2)
-1
L
-2
R
-1
L
-2
R
-3
L
-4
R
J404 (1/2)
-1
L
-2
R
-5
L
-6
R
-1
L
-2
R
-3
L
-4
R
R-CH
J403
R-CH
R-CH
R-CH
R-CH
J401
R-CH
R-CH
IC201
ATT
0/-6/-12/-18dB
R-CH
REC L2
REC L1
BAL L+
BAL R+
(0/6/12/18dB)
(0/6/12/18dB)
(0/6/12/18dB)
(0/6/12/18dB)
60
58
14
17
(0 – -99dB)
R-CH
R-CH
LOUT
ROUT
SLOUT
SROUT
COUT
SWOUT
55
40
39
38
33
(0 – -99dB)
(0 – -99dB)
37
(0 – -99dB)
34
J402 (2/2)
-4
J404 (2/2)
MUTE
Q361,362
R
OUT MD/TAPE
-3
L
-3
L
AUDIO
-4
OUT
R
MUTE
Q365,366
MUTE
Q364
VIDEO 1
MUTE
Q363
WOOFER
AMP
IC401
R-CH
R-CH
5456
47
41
42
36
3557
L-IN
R-IN
FL-CH
FR-CH
SL-CH
SR-CH
C-CH
DIGITAL
A
SECTION
(Page 17)
D
SECTION
(Page 19)
POWER
J405
SUB
WOOFER
AUDIO
OUT
TUNER
VOL IC/
TUNER
LATCH-VOL IC
WOOFER RELAY
STEREO
TUNED
MUTE
SLATCH
DATA
CLK
74
73
75
78
76
DO
14
15
16
STEREO
TUNED
MUTE
DO/DI
CE CLK
DATA
DIGITAL
SECTION
(Page 17)
L OUT
C OUT
C
SW OUT
SL OUT
LIN2
20
CIN2
24
SWIN2
25
SLIN2
23
DATA
28
CLK
27
LATCH
29
MCU
I/F
AVEE
SAVCC
DVDD
-7V
67
+7V
31
30
+3.3V
REG
Q471
Q379
INV.
+7V
RELAY
DRIVER
Q560
RY560
FC MUTE
• Signal path
: TUNER (FM/AM)
: CD (ANALOG)
DIGITAL
B
SECTION
(Page 17)
: VIDEO (AUDIO)
68
• R-ch is omitted due to
same as L-ch.
1616
Page 17
4-4. BLOCK DIAGRAM — DIGIT AL SECTION —
DIGITAL
TUNER/
AUDIO
SECTION
(Page 16)
DVD
IN
(COAXIAL)
VIDEO 2
IN
(OPTICAL)
CD/SACD
IN
(OPTICAL)
A
J1101
IC1105
IC1106
OUT
OUT
L-IN
R-IN
1
DE595
1
6721
23
X1101
12.288MHz
AMP
IC1502
R-CH
IC1102
WAVE
SHAPER
STR-DE495/DE595
CODEC
IC1501
DSP
DSI1
SCKOUTMCLKI
GP8
KFSI0
BCKI2
LRCKI2
DSI2
EXLOCK
GP9
68 56
BST
HCS
IC1201
HACN
2 1133635 33 3432
XRST
PM
SD01
236
SD02
247
SD03
258
GP10
67
LRCKO
195
BCKO
204
MCLK1
9
MCLK2
12
CSO
44
WEO
45
D0-15A0-15
108,107,105 -102,99,
112,110,109,97 - 92,
HDIN
HDOUT
HCLK
X1201
13.59MHz
98,80 - 77,75 - 72
85-82,66 - 64
+2.5V
VDDI
+3.3V
VDDE
SDTI1
SDTI2
SDTI3
LRCK
BCK
ROM
IC1202
CS
6
17
WE
D0-15A0-15
16-13,10 - 7
29 - 32,35 - 38,
1 - 5,18 - 21
24 - 27,42 - 44,
AUDIO
I/F
(2/2)
PD
S.MUTE
17
3 43 42 41
DAC
DAC
DAC
DAC
CDT1
CCLK
CS
LOUT1
LOUT 3
ROUT 3
LOUT 2
27
23
24
25
+5V-2
D.5V
L OUT
C OUT
SW OUT
SL OUT
• Signal path
: TUNER (FM/AM)
: CD (DIGITAL)
: VIDEO (AUDIO)
• R-ch is omitted due to
same as L-ch.
C
(Page 16)
TUNER/
AUDIO
SECTION
L IN-
29
L IN+
30
+5V-2
A.5V
DIR
IC1101
DIN2
5
INPUT
DIN1
4
DIN0
3
21
XOUT
22
XIN
VDD
+3.3V
DATA
DEMODULATOR
Pa,Pb DETECTIONLOCK
C bit DETECTION
MICROPROCESSOR
I/F
CLKCEDIDOBPSYNC
38 37 36 35 33 47 17
ADC
LPF
DETECTION
CKSEL1
NC
XSTATE
48
AUDIO
I/F
(1/2)
SDTO
918
3914
AUDIO
2469
CKOUT
1322
BCK
1429
LRCK
1528
DATAO
1630
ERROR
D1101
3459
TUNER/
AUDIO
SECTION
(Page 16)
Q1601
INV.
21
99
24
F.MUTE
ERROR
ANA/DIG
FC MUTE
B
Q1602
D1601
95 96 97 9894 100
CLK
DI
CE
DO
CKSEL1
93
XSTATE
DIR
XMODEXMODE
DATAO
3216 7418 19 205
GP9
BST
HCS
HACN
DSP
XRST
PM
HDIN
HDOUT
HCLK
SYSTEM
CONTROL
IC1601 (2/4)
8 9 10 12 13
PD
SMUTE
CODEC
CDT1
SCL
CS
1717
Page 18
STR-DE495/DE595
4-5. BLOCK DIAGRAM — VIDEO/DISPLAY SECTION —
COMPONENNT VIDEO SELECTOR
0X
12
1X
13
0Z
5
1Z
3
0Y
2
1Y
1
INH
6
SW3
SW2
SW4
461014
88
878990
SW3
SW2
SW4
VIDEO SW
VIDEO SELECTOR
SW1
SW1
COMPONENT
VIDEO
VIDEO 1
VIDEO 2
DVD/LD
FLASH
PROGRAMMING
VIDEO 2
IN
DVD IN
P
P
P
P
-1
VIDEO
IN
-2
VIDEO
IN
-1
VIDEO
IN
CNS3
1
2
7
6
5
+3.3V
(STBY)
B/B-Y
R/R-Y
B/B-Y
R/R-Y
J301 (1/2)
-4
Y
-5
-6
-1
Y
-2
-3
J201 (1/2)
J200 (1/2)
EEPROM
IC1604
SDA
SCL
S152
I
/
I
FLASH1
FLASH2
MD2
MD0
RESET
5
6
RESET
IC1602
X1601
20MHz
Q301
V1
13
V2
5
DVD
3
83
X1
X0
82
SDA
34
EEPROM
SCL
33
56
POWER KEY
28
FLASH1
27
FLASH2
MD2
51
MD0
49
77
12
RSTX
IC301
IC203
OR
SYSTEM
CONTROL
IC1601 (3/4)
SW5
2
D203,
D204
XCOM
ZOUT
YOUT
A
C
B
14
11
4
9
15
10
FL DRV/
LED DRV
M.OUT
V1.OUT
VCC
DIN
CLK
FL_STB
BLUE LED
SIRCS
VOL(A)
VOL(B)
A/D0
A/D1
A/D2
A/D3
VEE
EXCEPT AEP,UK MODEL
VIDEO AMP
IC302
VIN2
3
VIN3
5
VIN1
1
1
15
13
23
BUFFER
+5V
5
4
1
2
10
9
D101
DECODER
+V
-V
IC101
6
3
8
+5V
DE595
1
3
IC807
LED DRIVER
Q100
+5V
REG
-5V
REG
IC804
MULTI CHANNEL
16
8
61
62
63
46
54
60
59
38
39
40
41
VOUT2
11
VOUT3
9
VOUT1
1513
SEG1-16 GRID1-16
DIN
7
8
CLK
9
STB
RV102
MASTER
VOLUME
SW NETWORK S100-106
SW NETWORK S110-115
SW NETWORK S120-125
SW NETWORK S130-135,
FL101
FLUORESCENT
INDICATOR
TUBE
14 - 29 42 - 31
FL DISPLAY
DRIVER
IC100
J301 (2/2)
-7
-8
-9
J201 (2/2)
J200 (2/2)
1
SW1
SW2
2
SW3
3
4
SW4
S116
MULTI CH IN
S151
SPEAKERS
(OFF/A/B/A+B)
Y
P
P
B/B-Y
R/R-Y
VIDEO
OUT
VIDEO
OUT
-2
-1
F1
F2
DE595
MONITOR
OUT
MONITOR
VIDEO 1
SIRCS
D102 MUSIC
D103 MOVIE
D104 A.F.D.
D105 2CH
OUT
1
REMOTE
CONTROL
RECEIVER
IC102
• Signal path
: VIDEO
1818
Page 19
4-6. BLOCK DIAGRAM — POWER SECTION —
PRE DRIVER
IC701
IN 2
PRE
FL-CH
FR-CH
R-CH
8
1
MUTE
DRIVE
DRIVE
+VOUT2
-VOUT2
-BB +B
STR-DE495/DE595
J791
PHONES
R-CH
12
11
POWER AMP
Q701-704
R-CH
CURRENT
DETECT
Q705,706
R-CH
OVERLOAD
DETECT
D740,Q740
R-CH
RELAY
DRIVER
Q790
RELAY
DRIVER
Q710
RY791
RY701
R-CH
TM602
TM603
L
FRONT (DE495)
FRONT A
R
(DE595)
DE595
TUNER/
AUDIO
SECTION
(Page 16)
D
SL-CH
SR-CHR-CH
C-CH
MUTE
BUFFER
Q747,748
8
1
1
22
IN 2
MUTE
IN+
AC MUTE
PRE
DRIVE
PRE
DRIVE
PROTECTOR
HEADPHONE
RELAY
PREOUT/FRONT
RELAY
REAR RELAY
CENTER RELAY
HP DETECT
SPK B RELAY
R1 RELAY
SYSTEM
CONTROL
IC1601 (4/4)
POWER RELAY
PRE DRIVER
IC702
DRIVE
PRE DRIVER
IC501
DRIVE
66
D734
D733
67
71
69
70
25
17
72
DE595
65
+VOUT2
-VOUT2
-BB +B
+VOUT
-VOUT
-BB +B
D731
12
11
6
5
PROTECTOR
D721,722
Q722,723,725
HP-RY
FRONT-RY
REAR-RY
CENTER-RY
HP DETECT
SPK B-RY
POWER AMP
Q651-654
POWER AMP
Q501-504
IC601
OVERLOAD
DETECT AMP
-BB
TM601
RELAY
Q809
L
FRONT B
R
L
SURROUND
R
CENTER
RY802 RY803
IC1904
+3.3V
REG
SPEAKERS
IMPEDANCE
USE 8-16Ω
RELAY
DRIVER
Q901
13
D902-905
F1
F2
-30V
D910-913
RELAY
DRIVER
Q851
IC1902
+10V
REG
IC801
+7V
REG
-7V
REG
IC802
IC1903
+5V
REG
RY601
RY501
13
13
23
13
RECT
D802
+V
-V
RELAY
REAR-RY
CENTER-RY
4
DRIVER
Q610
RELAY
DRIVER
Q510
HP DETECT
CURRENT
DETECT
Q655,656
R-CHR-CH
R-CH
CURRENT
DETECT
Q505,506
+B
-B
Q691
+3.3V
(STBY)
TU+3.3V
TU+10V
+5V-2
+5V-1
+2.5V
+3.3V
Q692
72
-30V
+7V
-7V
OVERLOAD
DETECT
D640,Q640
OVERLOAD
DETECT
D540,Q540
-30V REG
Q801
AEP,UK M0DEL
5
2
HP-RY
FRONT-RY
IC1905
+3.3V
REG
IC1503
+5V
REG
IC1901
BACK-UP
SWITCH
SPK B-RY
13
13
RY851
R-CH
R-CH
DE595
EXCEPT
DE595:CND MODEL
DE595:CND MODEL
DRIVER
• Signal path
: TUNER (FM/AM)
• R-ch is omitted due to
same as L-ch.
DE495
RY801
RECT
D820-823
RECT
RY901
RECT
R810
R812
R910
D804
T901
POWER
TRANSFORMER
EXCEPT
E2
M0DEL
E2 M0DEL
T902
POWER
TRANSFORMER
JW907
F901
JW906
JW910
JW905
E2 M0DEL
S901
VOLTAGE
SELECTOR
240V
220V
120V
-1
-2
JW909
JW904
EXCEPT
E2
MODEL
JW908
EXCEPT
E2
MODEL
~ AC IN
STOP
Q921
48
D914
D915
1919
Page 20
STR-DE495/DE595
Ver 1.1
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
f
•
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
• A : B+ Line.
• B : B– Line.
•Voltage and waveforms are dc with respect to ground
•Voltages are taken with a VOM (Input impedance 10 MΩ).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
• Abbreviation
: internal component.
Note:
The components identified by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
under no-signal (detuned) conditions.
no mark : FM
Voltage var iations may be noted due to normal production tolerances.
Voltage var iations may be noted due to normal production tolerances.
F: TUNER (FM/AM)
L : VIDEO (AUDIO)
I : VIDEO
J: CD (ANALOG)
c : CD (DIGITAL)
CND : Canadian model.
AUS : Australian model.
MX: Mexican model.
SP: Singapore model.
E2: AC 120 V area in E model.
AR: Argentine model.
KR: Korean model.
TW: Taiwan model.
4
W or less unless otherwise
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
for printed wiring boards:
• X : parts extracted from the component side.
f
•
•: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)parts face are indicated.
•Abbreviation
: internal component.
CND : Canadian model.
AUS: Australian model.
MX: Mexican model.
SP: Singapore model.
E2: AC 120 V area in E model.
AR: Argentine model.
KR: Korean model.
TW: Taiwan model.
C
Q
B
E
Q
BCE
Q
B
C
These are omitted.
These are omitted.
E
• Waveforms (DIGITAL Board)
1V/DIV 50nsec/DIV
1
3.4Vp-p
12.288MHz
IC1101
1V/DIV 0.2µsec/DIV
2
IC1101
1V/DIV 50nsec/DIV
3
IC1101
1V/DIV 50nsec/DIV
4
IC1501
1V/DIV 50nsec/DIV
5
IC1201
1V/DIV 50nsec/DIV
6
IC1201
1V/DIV 50nsec/DIV
7
IC1601
(CKOUT)
qd
3.07MHz
(BCK)
qf
12.288MHz
(XOUT)
wa
12.288MHz
(MCLKI)
el
13.59MHz
(MCLK2)
qs
12.288MHz
(SCKOUT)
qf
16MHz
id
3.4Vp-p
3.2Vp-p
4.4Vp-p
3.4Vp-p
3.4Vp-p
2.5Vp-p
(X1)
2020
Page 21
4-7. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 15 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards.
4-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 20 for Common Note on Schematic Diagram and page 34 for IC Block Diagrams.
J404
C500
J403
C900
J402
J401
C700
CC07
CC57
CC06
CC56
CC08
CC58
CC05
CC55
CC04
CC54
CC09
CC59
CC02
CC52
CC61
CC62
CC32
CC42
R407
R457
R406
R456
R408
R458
R405
R455
R409
R402
KR, TW
R461
R462
R432
R412
R404
R454
R459
R452
C461
C462
C432
C412
C407
C457
C406
C456
C408
C458
C405
C455
C404
C454
C409
C459
C402
C452
KR, TW
C413C433
C464
C465
IC B/D
C491
IC201
R410
C481 C483
R430
C414
C415
C417
C416
C418
C492
C482
C484
C494
C419
R476
R477
C493
C485
R478
C497
C490
C489
R475
R471
R472
C487C495C496
C488
C466
C467
Q471
C486
R377
R378
R373
R363
R360
R374
R375
R367
R376
R371
R372
R368
Q361
Q362
Q363
Q364
Q365
Q366
R361
C371
C372
R362
R379
C373
C374
R366
R369
C375
C376
R370
R380
Q379
(Page 23)
R381
(Page 26)
(Page 27)
J405
CNP501
CNP502
C800
R469
C400
R802
CC31
CC41
R479
RY560
D560
R431
C431
R411 C411
Q560
R470
R533
R532
R560
IC401
R499
C471
R473
R474
C498
C472
2222
Page 23
4-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 20 for Common Note on Schematic Diagram and page 34 for IC Block Diagrams.
STR-DE495/DE595
Ver 1.1
(Page
22)
C501
C751
C601
Q747
C701
C651
R743
Q748
R751
R601
IC B/D
R501
C507
R701
R651
IC601
R742
C741
IC B/D
IC702
C757
C607
R696
R694
R502
C707
C657
IC B/D
R752
R602
C508
C503
IC701
R702
R652
R503
504
R
R744
C505
R505
C605
C606
R603
IC501
C506
C504
R695
C655
R604
C691
C656
C653
C756
C604
C603
R690
R693
C706
C654
C704
R654R704
R653
R703
C703
C755
C754
R754
R753
C616
C753
R733
D691
R691
R692
C705
Q692
D690
Q691
R698
R699
C617
C733
C732
R732
C710
C660
C610
C760
C510
Q701
Q651
Q601
751
Q
Q501
R710R711
Q702
Q652
R660R661
Q602
Q752
R760
R510R511
Q502
R713
R663
R611R610
R613
R763
R761
R513
C717
R714
R715
R665
R664
R614
R615
R765
R764
R514
R515
C666
C621
C517
C716
C669
C620
C767
C766
C516
R716
R666
R616
R766
R516
C720
703
Q
R719
R721R722
Q704
R725
R638
Q654
R671
653
Q
C670
669
R
C619
603
Q
620
R
R621
Q604
R625
R775
Q754
R771
R772
753
Q
C770
R769
C519
503
Q
R520
R521
Q504
R622
R522
C805
C806
CNP801
CNP914
CNP791
C792
C790
J791
(Page 33)
(Page 33)
CN792
Q710
C721
Q851
R852
R791
Q610
Q550
R804
R731
R735
D801
R792
R794
Q790
R631
R531
R803
D731
734
D
Q740
R745
R740
C742
R748
R680
R681
R750
R758
R540
R546
R747
R748
3.3k
6.8k
C642
R648
R681
3.3k
6.8k
C752
R757
R758
3.3k
6.8k
R557
R648
3.3k
6.8k
C681
C541
D740
C740
(DE495)
(DE595)
D640
R677
(DE495)
(DE595)
D680
R657
(DE495)
(DE595)
D750
C750
(DE495)
(DE595)
D540
C540
R546
3.3k
6.8k
Q680
Q750
Q540
(DE495)
(DE595)
Q640
C640
C680
L701
L651
R668
L601
R618
L751
R768
R718
R675
R676
R655
R656
R755
R555
R556
R746
R756
R734
D710
Q725
D721
R736
RY851
R851D851
R634
L521
R528
R534
C822
804
D
C801
R806
RY701
R780
D722
R737
R770
Q723
Q722
C722
RY601
D610
RY501
D510
Q801
C802
Q705
R724
D705
C711
R723
R717
Q706
R667
R673
655
Q
C661
R640
D665
672
R674
R
Q656
Q605
R624
D605
C611
R623
Q606
R617
Q755
R778
D765
R773
C761
R767
Q756
R517
R573
C511
Q505
R524
D505
Q506
R525
D732
3
73
D
RY791
D791
R793
CC12RR11
AEP, UK, AUS, KR, TW MODEL
AEP, UK, AUS, KR, TW MODEL
CC14
AEP, UK, AUS, KR, TW MODEL
RR16
RR17 CC34
AEP, UK, AUS, KR, TW MODEL
RR14 CC18
RR13 CC16
AEP, UK, AUS, KR, TW MODEL
AEP, UK, AUS, KR, TW MODEL
RR15
D802
C803
C804
TM602
RR12
CC33
TM603
TM601
CC20
(Page 33)
(Page 27)
CNP911
IC801
C807
C808
D896
IC802
2323
C811
C810
C820
C903
C821
D905
D904
D902
D903
C901
C830
R910
Note:
The components identified by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
CN505
CNP915
CNP802
(Page 29)
(Page 33)
(Page 33)
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
Page 24
STR-DE495/DE595
4-10. PRINTED WIRING BOARD — DIGIT AL SECTION (1/2) — • Refer to page 15 for Circuit Boards Location and page 20 for Common Not e on Printed Wiring Boards.
4-11. PRINTED WIRING BOARD — DIGITAL SECTION (2/2) — • Refer to page 15 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards.
4-12. SCHEMATIC DIAGRAM — DIGITAL SECTION (1/2) — • Refer to page 20 for Common Note on Schematic Diagram and Waveforms and page 34 for IC Block Diagrams.
R1504
J1101
IC1105
IC1106
R1100
C1109
C1110
C1129
X1101
IC B/D
R1124
R1101
R1110
R1113
C1113
C1131
FB1102
FB1202FB1201
C1230
C1211
C1212
C1231
IC1202
TP1220
TP1219
TP1218
TP1217
TP1216
R1230
R1231
R1232
R1233
R1234
R1235
C1214
C1213
R1236
R1237
R1238
C1204C1205
R1239
R1240
R1241
R1242
R1243
R1244
TP1215
(Page 27)
R1204
C1203
C1218
TP1214
R1108
R1111
IC1101
C1108
C1111
C1105
C1112
R1112
R1115
FB1105FB1104
R1102
D1101
R1103
R1114
R1121
JR1116
C1121
R1123
C1119
C1124
FB1101
C1115
C1107
R1106
C1101
D1001
IC1102
R1109
C1123
R1116
C1118
C1130
C1502R1506R1505
C1116
JR1122
C1106
C1117
C1103
C1102
JR1115
R1107
R1105
R1104
C1104
R1117
R1118
R1119
C1114
C1501
C1551
(Page 22)
R1501
R1554
R1503
R1553
R1502
R1555 R1556
R1552R1551
C1552
C1504
CNS1
IC1502
R1557
IC1552
C1503
R1507
C1513
C1515
C1514
R1508
FB1501
C1506
IC1503
C1505
R1509
R1520
R1521
R1518
R1519
IC1501
R1516
R1517
IC B/D
FB1502
R1229
R1228
C1216
R1227
R1226
R1225
R1224
R1222
R1221
R1220
R1219
R1218
R1217
R1216
R1215
R1214
R1213
R1212
R1203
C1208
TP1221
TP1222
C1219
R1210
C1210
TP1201
X1201
FB1204
R1202
IC1201
C1209
TP1202
R1209
FB1203
R1206
R1207
R1208
TP1203
TP1204
TP1213
TP1212
TP1211
TP1210
TP1209
TP1208
TP1207
TP1206
TP1205
C1220
C1202
C1201
C1511
C1512
D1502D1501
C1508
C1507
C1509
C1510
C1523
C1206
C1207
(Page 27)
C1516
C1517
C1518
C1519
C1520
C1521
R1205
JR1121
2626
Page 27
4-13. SCHEMATIC DIAGRAM — DIGITAL SECTION (2/2) — • Refer to page 20 for Common Note on Schematic Diagram and Waveforms.
STR-DE495/DE595
Ver 1.1
CNP5
(Page 29)
TM301
(Page 26)
CNS8
CNS7
C1914
C1915
C1221
IC1902
IC1905
C1309
C1310
C1913
C1916
C1311
C1227
R1314
R1364
R1710
R1711
R1705
R1642
C1612
C1627
IC1602
C1626
R1709
C1229
R1659
R1637
R1676
R1677
R1678
R1679
R1643
R1694
R1644
R1645
R1646
R1647
R1648
R1706
C1617
R1649
R1601
R1655
X1601
IC1903
C1619
R1305
R1304
R1690
C1909
R1674
R1603
R1604
R1668
R1673
R1605
R1308
R1606
R1664
R1607
R1665
R1608
R1609
R1623
R1699
R1610
R1698
R1638
R1611
R1631
R1612
R1602
R1613
R1667
IC1601
R1614
C1908C1910
R1600
R1615
R1669
R1641
R1617
C1906
R1640
R1618
R1639
R1619
C1611
C1610
R1621
R1707
R1708
C1601
D1601
Q1601
R1689
IC1901
C1625
R1658
C1905
R1704
R1703
JR1112
JR1113
R1624
R1625
L1901
C1911
Q1602
C1607
C1671
R1630
R1629
R1628
R1627
R1663
R1635
R1687
R1633
R1672
C1632
C1602
R1662
R1626
IC1904
R1660
R1686
R1685
R1684
R1683
R1670
R1650
C1624
FB1602
R1656
FB1601
R1651
C1634
R1657
R1654
C1912
C1606
C1616
C1615
C1614
C1613
C1618
R1636
C1605
C1604
C1620
C1603
R1632
R1671
JR1114
C1633
R1682
C1635
C1312
R1688
IC1604
R1681
R1666
FB1603
R1622
CNP6
CNS4
CNS3
CNS2
AR
(Page 33)
(Page 23)
(Page 31)
KR, TW
AR
KR, TW
(Page 26)
2727
R1616
(Page 22)
Page 28
STR-DE495/DE595
Ver 1.1
4-14. PRINTED WIRING BOARD — VIDEO SECTION — • Refer to page 15 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards.
A
B
C
D
E
1
• Semiconductor
Location
Ref. No. Location
D203G-4
D204F-4
IC203F-7
(IC301)G-8
(IC302)H-12
IC804H-3
IC807H-3
(Q301)H-5
( ):Except for AEP,
UK model
234567891011121314
DE495, DE595:
J301
J200J201
R221
C207
C206
C248
R218
JW214
C200
JW212
R200
JW207
C208
R220
C201
R201
R309
C311
R307
R308
C309
JW300
F
G
H
R312
C329
R301
JW454
R302
R311
IC302
T20
R305
JW323
R306
JW324
JW350
R304
C332
C313
R303
C302
R310
JW328
IC301
JW331
C214
JW320
JW326
C312
C310
JW319
JW322
C308
JW321
C331
JW325
JW327
T21
IC203
R325
JW315
JW317
C330
JW203
Q301
C215
R347
JW211
JW223
C338
C210
JW220
JW316
C317
(Page 25)
JW206
IC807
JW224
CNS250
JW225
IC804
JW213
D204
D203
C827
C824
JW216
C213
C809
CNP156
JW221
JW222
I
C825
C301
C303
R313
J
(Page 21)
2828
Page 29
4-15. SCHEMATIC DIAGRAM — VIDEO SECTION — • Refer to page 20 for Common Note on Schematic Diagram and page 34 for IC Block Diagrams.
IC807
STR-DE495/DE595
Ver 1.1
CNP156
J201
J200
C248
R220
C201
C200
R218
R221
C208
R201
R200
C206
C207
IC B/D
IC203
C214
C827
C809
C210
IC804
C824
C825
C329
R313
C332
C330
C317
C331
C338
IC302
IC301
C303R301
C301
C302
R312R311
R310
IC B/D
JW300
C313
C308
C309
R306R305R304
IC B/D
(Page 23)
DE495, DE595:
J301
R302
R303
(Page 27)
CNS250
D203
D204
C215
C213
R347
R325
Q301
C310
C311
C312
R309R308R307
2929
Page 30
STR-DE495/DE595
4-16. PRINTED WIRING BOARDS — DISPLAY SECTION — • Refer to page 15 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards.
A
B
C
D
1
S151
S152
234567891011121314
JW122
S104
CNS100
(Page 25)
CNP104
RV102
JW129
CNP102
CN101
S135
R136
S134
R135
JW101
JW100
S133
S122
R153
IC102
R133
R134
R155
S132
S121
C114
R123
R122
C105
S125
R154
S123
R132
S131
R198
R131
R124
C108
S130
R125
S124
D105
R161
R121
FL101
S113
S120
D104
R114
D101
R113
C104
R162
JW104
S114
D103
R115
C100
C144
S112
JW103
JW102
Q100
C132
C133
C134
S115
D102
IC100
C135
R116
C136
R112
S111
C137
JW105
C101
C138
JW106
C139
JW112
JW108
JW107
R150
C140
C141
R160
R111
C110
S116
C142
C111
C143
C112
R141
C109
S110
JW109
JW111
JW110
R199
C115
L103
JW115
JW114
JW113
R174
S100
R173
R172
S105
R175
R105
IC101
R106
R101
JW116
C157
S106
S101
JW124
L102
JW117
R102
JW125
L101
JW126
C151
C150
JW118
JW119
C152
JW120
JW130
C154
C153
JW127
JW128
S103
R103
S102
JW123
R104
JW121
C156
C155
CN103
E
• Semiconductor
Location
Ref. No.Location
(D101)B-8
D102A-8
D103A-8
D104A-7
D105A-7
IC100C-8
IC101C-10
IC102C-4
(Q100)C-8
( ): STR-DE595 only
3030
Page 31
4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 20 for Common Note on Schematic Diagram.
STR-DE495/DE595
C108
R198
C151
C150
C152
R101
C109
C133
C134
C135
C136
IC100
C137
C138
C139
C132
FL101
R161
D103D104D105
D102
R172
R173
R174
R150
C101
C140
C141
C142
C143
R199
R175
C144
D101
R141
R160
R162
C104
Q100
S100S101S102S103S104S105S106
S110S111S112S113S114S115
S120S121S122S123S124S125
S130S131S132S133S134S135
R111
R121
R102
R131
R112
R122
CN101
R103
R132
R113
R123
R104
R133
CNP102
R114
R124
R105
R134
R115
R125
R135
R106
R116
S116
R136
IC101
S151
C111
C100
C112
C154C153
C110
C115
IC102
C105
C114
R155
R154
R153
L102
C156
C155
L103
C157
L101
CN103
CNS100
CNP104
S152
RV102
(Page 27)
3131
Page 32
STR-DE495/DE595
Ver 1.1
4-18. PRINTED WIRING BOARDS — POWER SECTION — • Refer to page 15 for Circuit Boards Location and page 20 for Common Note on Printed Wiring Boards.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
•Abbreviation
CND : Canadian model
AUS: Australian model
MX : Mexican model
SP : Singapore model
E2 : AC 120 V area in E model
AR : Argentine model
KR : Korean model
TW : T aiwan model
5-1. CASE SECTION
SECTION 5
EXPLODED VIEWS
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
Parts Color Cabinet’s Color
• Accessories are given in the last of this parts list.
3
R
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
1
3
2
3
#1
#1
Ref. No.Part No.DescriptionRemark
14-245-939-01 CASE (BLACK)...(BLACK)
14-245-939-21 CASE (SILVER)...(SILVER)
14-245-939-41 CASE (GOLD)...(GOLD)
2X-4953-448-1 FOOT ASSY
101A-4732-412-A DIGITAL BOARD, COMPLETE (DE595:US,CND)
101A-4732-431-A DIGITAL BOARD, COMPLETE (DE495:AEP,UK)
101A-4732-594-A DIGITAL BOARD, COMPLETE (DE595:AUS)
101A-4732-607-A DIGITAL BOARD, COMPLETE (DE595:SP,MY,KR)
101A-4732-612-A DIGITAL BOARD, COMPLETE (DE595:E2)
101A-4732-615-A DIGITAL BOARD, COMPLETE (DE595:MX,AR)
101A-4732-625-A DIGITAL BOARD, COMPLETE (DE595:AEP,UK)
101A-4732-631-A DIGITAL BOARD, COMPLETE (DE495:KR,SP,MY)
101A-4734-333-A DIGITAL BOARD, COMPLETE (DE595:TW)
101A-4734-359-A DIGITAL BOARD, COMPLETE (DE495:TW)
101A-4734-763-A DIGITAL BOARD, COMPLETE (DE495:AUS)
* 1023-703-044-26 LABEL, CAUTION (US,CND)
01031-696-847-11 CORD, POWER (AUS)
01031-769-079-22 CORD, POWER (KR)
01031-777-071-23 CORD, POWER (AEP,UK,E2,SP,MY)
0 T9011-437-999-11 TRANSFORMER, POWER (DE495:AUS)
0 T9011-439-549-11 TRANSFORMER, POWER (DE595:US,MX)
0 T9011-439-550-11 TRANSFORMER, POWER
0 T9011-439-551-11 TRANSFORMER, POWER (DE595:SP,MY)
0 T9011-439-552-11 TRANSFORMER, POWER (DE595:TW)
0 T9011-439-553-11 TRANSFORMER, POWER (DE595:E2)
0 T9011-439-609-11 TRANSFORMER, POWER (DE595:CND)
0 T9011-439-640-11 TRANSFORMER, POWER (DE495:TW)
#27-685-880-09 SCREW +BVTT 4X6 (S)
#37-685-645-79 SCREW +BVTP 3X6 TYPE2 IT-3
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
(DE495:AEP,UK,KR,SP,MY)
(DE595:AEP,UK,AUS,AR,KR)
39
Page 40
STR-DE495/DE595
Ver 1.1
BRIDGEABLE
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
A-4732-412-A DIGITAL BOARD, COMPLETE (DE595:US,CND)
A-4732-431-A DIGITAL BOARD, COMPLETE (DE495:AEP,UK)
A-4732-594-A DIGITAL BOARD, COMPLETE (DE595:AUS)
A-4732-607-A DIGITAL BOARD, COMPLETE (DE595:MY,SP,KR)
A-4732-612-A DIGITAL BOARD, COMPLETE (DE595:E2)
A-4732-615-A DIGITAL BOARD, COMPLETE (DE595:MX,AR)
A-4732-625-A DIGITAL BOARD, COMPLETE (DE595:AEP,UK)
A-4732-631-A DIGITAL BOARD, COMPLETE (DE495:KR,SP,MY)
A-4734-333-A DIGITAL BOARD, COMPLETE (DE595:TW)
A-4734-359-A DIGITAL BOARD, COMPLETE (DE495:TW)
A-4734-763-A DIGITAL BOARD, COMPLETE (DE495:AUS)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
DIGITAL
BRIDGEABLE BOARD (DE595)
*****************
< CONNECTOR >
< DIODE >
< TRANSISTOR >
< RESISTOR >
< RELAY >
***********************
ELECTRICAL PARTS LIST
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
•Abbreviation
CND : Canadian model
AUS: Australian model
MX : Mexican model
SP : Singapore model
E2 : AC 120 V area in E model
AR : Argentine model
KR : Korean model
TW : Taiw an model
SECTION 6
(DE595)
(CND)
(EXCEPT CND)
(CND)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
IC1202 8-759-538-16 IC IS61LV6416-10TT(ISSI)
IC1501 6-703-705-01 IC AK4527B
IC1502 8-759-710-97 IC NJM4565M-D
IC1503 8-759-231-53 IC TA7805S
IC1552 8-759-710-97 IC NJM4565M-D
IC1601 6-802-541-01 IC MB9047BPF-G-138-BND
IC1602 6-702-913-01 IC S-80929CNMC-G8Z-T2
IC1604 8-759-641-86 IC BR24C16F-E2
IC1901 6-701-887-02 IC SI-3004KWF
IC1902 8-759-656-35 IC NJM7810FA
IC1903 8-759-450-47 IC BA05T
IC1904 8-759-445-59 IC BA033T
IC1905 8-759-647-10 IC uPC2933HF (AEP,UK)
< JACK >
J11011-794-972-11 JACK, PIN 1P (DIGITAL DVD IN (COAXIAL))
< JUMPER RESISTOR >
JR1112 1-216-864-11 METAL CHIP05%1/10W
(EXCEPT AEP,UK)
JR1113 1-216-864-11 METAL CHIP05%1/10W
(EXCEPT AEP,UK)
JR1114 1-216-864-11 METAL CHIP05%1/10W
(EXCEPT AEP,UK)
JR1115 1-216-864-11 METAL CHIP05%1/10W
(DE495)
JR1116 1-216-864-11 METAL CHIP05%1/10W
JR1121 1-216-864-11 METAL CHIP05%1/10W
JR1122 1-216-864-11 METAL CHIP05%1/10W
L19011-216-864-11 METAL CHIP05%1/10W
(DE595)
R1124 1-216-809-11 METAL CHIP1005%1/10W
R1202 1-216-809-11 METAL CHIP1005%1/10W
R1203 1-216-833-11 METAL CHIP10K5%1/10W
R1204 1-216-821-11 METAL CHIP1K5%1/10W
R1205 1-216-809-11 METAL CHIP1005%1/10W
R1206 1-216-809-11 METAL CHIP1005%1/10W
R1207 1-216-809-11 METAL CHIP1005%1/10W
R1208 1-216-809-11 METAL CHIP1005%1/10W
R1209 1-216-809-11 METAL CHIP1005%1/10W
R1210 1-216-833-11 METAL CHIP10K5%1/10W
R1212 1-216-813-11 METAL CHIP2205%1/10W
R1213 1-216-813-11 METAL CHIP2205%1/10W
R1214 1-216-813-11 METAL CHIP2205%1/10W
R1215 1-216-813-11 METAL CHIP2205%1/10W
R1216 1-216-813-11 METAL CHIP2205%1/10W
R1217 1-216-813-11 METAL CHIP2205%1/10W
R1218 1-216-813-11 METAL CHIP2205%1/10W
R1219 1-216-813-11 METAL CHIP2205%1/10W
R1220 1-216-813-11 METAL CHIP2205%1/10W
R1221 1-216-813-11 METAL CHIP2205%1/10W
R1222 1-216-813-11 METAL CHIP2205%1/10W
R1224 1-216-813-11 METAL CHIP2205%1/10W
R1225 1-216-813-11 METAL CHIP2205%1/10W
R1226 1-216-813-11 METAL CHIP2205%1/10W
R1227 1-216-813-11 METAL CHIP2205%1/10W
R1228 1-216-813-11 METAL CHIP2205%1/10W
R1229 1-216-813-11 METAL CHIP2205%1/10W
R1230 1-216-813-11 METAL CHIP2205%1/10W
R1231 1-216-813-11 METAL CHIP2205%1/10W
R1232 1-216-813-11 METAL CHIP2205%1/10W
R1233 1-216-813-11 METAL CHIP2205%1/10W
R1234 1-216-813-11 METAL CHIP2205%1/10W
R1235 1-216-813-11 METAL CHIP2205%1/10W
R1236 1-216-813-11 METAL CHIP2205%1/10W
R1100 1-216-857-11 METAL CHIP1M5%1/10W
R1101 1-216-833-11 METAL CHIP10K5%1/10W
R1102 1-216-833-11 METAL CHIP10K5%1/10W
R1103 1-216-809-11 METAL CHIP1005%1/10W
R1104 1-216-809-11 METAL CHIP1005%1/10W
R1105 1-216-829-11 METAL CHIP4.7K5%1/10W
R1106 1-216-839-11 METAL CHIP33K5%1/10W
R1107 1-216-830-11 METAL CHIP5.6K5%1/10W
R1108 1-216-809-11 METAL CHIP1005%1/10W
R1109 1-216-809-11 METAL CHIP1005%1/10W
R1110 1-216-821-11 METAL CHIP1K5%1/10W
R1111 1-216-821-11 METAL CHIP1K5%1/10W
R1112 1-216-809-11 METAL CHIP1005%1/10W
R1113 1-216-821-11 METAL CHIP1K5%1/10W
R1114 1-216-809-11 METAL CHIP1005%1/10W
R1115 1-216-833-11 METAL CHIP10K5%1/10W
R1116 1-218-285-11 METAL CHIP755%1/10W
R1117 1-216-821-11 METAL CHIP1K5%1/10W
R1118 1-216-854-11 METAL CHIP560K5%1/10W
R1119 1-216-837-11 METAL CHIP22K5%1/10W
R1121 1-216-809-11 METAL CHIP1005%1/10W
R1237 1-216-813-11 METAL CHIP2205%1/10W
R1238 1-216-813-11 METAL CHIP2205%1/10W
R1239 1-216-813-11 METAL CHIP2205%1/10W
R1240 1-216-813-11 METAL CHIP2205%1/10W
R1241 1-216-813-11 METAL CHIP2205%1/10W
R1242 1-216-813-11 METAL CHIP2205%1/10W
R1243 1-216-813-11 METAL CHIP2205%1/10W
R1244 1-216-813-11 METAL CHIP2205%1/10W
R1304 1-216-841-11 METAL CHIP47K5%1/10W
R1305 1-216-841-11 METAL CHIP47K5%1/10W
R1308 1-216-809-11 METAL CHIP1005%1/10W
R1314 1-216-864-11 METAL CHIP05%1/10W
R1364 1-216-864-11 METAL CHIP05%1/10W
R1501 1-216-815-11 METAL CHIP3305%1/10W
R1502 1-216-833-11 METAL CHIP10K5%1/10W
R1503 1-216-833-11 METAL CHIP10K5%1/10W
R1504 1-216-815-11 METAL CHIP3305%1/10W
R1505 1-216-830-11 METAL CHIP5.6K5%1/10W
R1506 1-216-837-11 METAL CHIP22K5%1/10W
R1507 1-216-829-11 METAL CHIP4.7K5%1/10W
R1508 1-216-845-11 METAL CHIP100K5%1/10W
R1509 1-216-821-11 METAL CHIP1K5%1/10W
R1516 1-216-813-11 METAL CHIP2205%1/10W
R1517 1-216-813-11 METAL CHIP2205%1/10W
R1518 1-216-813-11 METAL CHIP2205%1/10W
R1519 1-216-813-11 METAL CHIP2205%1/10W
R1520 1-216-813-11 METAL CHIP2205%1/10W
R1521 1-216-813-11 METAL CHIP2205%1/10W
R1551 1-216-815-11 METAL CHIP3305%1/10W
R1552 1-216-833-11 METAL CHIP10K5%1/10W
R1553 1-216-833-11 METAL CHIP10K5%1/10W
R1554 1-216-815-11 METAL CHIP3305%1/10W
R1555 1-216-830-11 METAL CHIP5.6K5%1/10W
R1556 1-216-837-11 METAL CHIP22K5%1/10W
R1557 1-216-829-11 METAL CHIP4.7K5%1/10W
R1600 1-216-829-11 METAL CHIP4.7K5%1/10W
R1601 1-216-821-11 METAL CHIP1K5%1/10W
R1602 1-216-829-11 METAL CHIP4.7K5%1/10W
R1603 1-216-821-11 METAL CHIP1K5%1/10W
R1604 1-216-809-11 METAL CHIP1005%1/10W
R1605 1-216-809-11 METAL CHIP1005%1/10W
R1606 1-216-821-11 METAL CHIP1K5%1/10W
R1607 1-216-821-11 METAL CHIP1K5%1/10W
R1608 1-216-821-11 METAL CHIP1K5%1/10W
R1609 1-216-821-11 METAL CHIP1K5%1/10W
R1610 1-216-821-11 METAL CHIP1K5%1/10W
R1611 1-216-821-11 METAL CHIP1K5%1/10W
R1612 1-216-821-11 METAL CHIP1K5%1/10W
R1613 1-216-821-11 METAL CHIP1K5%1/10W
R1614 1-216-821-11 METAL CHIP1K5%1/10W
R1615 1-216-821-11 METAL CHIP1K5%1/10W
R1616 1-216-821-11 METAL CHIP1K5%1/10W
(DE595)
R1617 1-216-809-11 METAL CHIP1005%1/10W
R1618 1-216-809-11 METAL CHIP1005%1/10W
R1619 1-216-809-11 METAL CHIP1005%1/10W
R1621 1-216-821-11 METAL CHIP1K5%1/10W
R1622 1-216-833-11 METAL CHIP10K5%1/10W
(DE495)
R1623 1-216-829-11 METAL CHIP4.7K5%1/10W
(DE595)
R1624 1-216-833-11 METAL CHIP10K5%1/10W
R1625 1-216-833-11 METAL CHIP10K5%1/10W
R1626 1-216-833-11 METAL CHIP10K5%1/10W
R1627 1-216-833-11 METAL CHIP10K5%1/10W
R1628 1-216-833-11 METAL CHIP10K5%1/10W
R1629 1-216-833-11 METAL CHIP10K5%1/10W
R1630 1-216-833-11 METAL CHIP10K5%1/10W
R1631 1-216-829-11 METAL CHIP4.7K5%1/10W
R1632 1-216-825-11 METAL CHIP2.2K5%1/10W
(AEP,UK)
R1632 1-216-829-11 METAL CHIP4.7K5%1/10W
(SP,MY,KR,TW)
R1632 1-216-833-11 METAL CHIP10K5%1/10W
(E2)
R1632 1-216-841-11 METAL CHIP47K5%1/10W
(AUS,MX,AR)
R1632 1-216-864-11 METAL CHIP05%1/10W
(US,CND)
R1633 1-216-833-11 METAL CHIP10K5%1/10W
(AUS)
R1633 1-216-837-11 METAL CHIP22K5%1/10W
(MX,AR)
R1633 1-216-841-11 METAL CHIP47K5%1/10W
(AEP,UK,E2,SP,MY,KR,TW)
R1635 1-216-833-11 METAL CHIP10K5%1/10W
R1636 1-216-833-11 METAL CHIP10K5%1/10W
R1637 1-216-833-11 METAL CHIP10K5%1/10W
R1638 1-216-829-11 METAL CHIP4.7K5%1/10W
R1639 1-216-809-11 METAL CHIP1005%1/10W
R1640 1-216-809-11 METAL CHIP1005%1/10W
R1641 1-216-809-11 METAL CHIP1005%1/10W
R1642 1-216-833-11 METAL CHIP10K5%1/10W
R1643 1-216-821-11 METAL CHIP1K5%1/10W
R1644 1-216-821-11 METAL CHIP1K5%1/10W
R1645 1-216-821-11 METAL CHIP1K5%1/10W
R1646 1-216-821-11 METAL CHIP1K5%1/10W
R1647 1-216-821-11 METAL CHIP1K5%1/10W
R1648 1-216-821-11 METAL CHIP1K5%1/10W
R1649 1-216-821-11 METAL CHIP1K5%1/10W
R1650 1-216-833-11 METAL CHIP10K5%1/10W
R1651 1-216-833-11 METAL CHIP10K5%1/10W
R1654 1-216-833-11 METAL CHIP10K5%1/10W
R1655 1-216-833-11 METAL CHIP10K5%1/10W
R1656 1-216-841-11 METAL CHIP47K5%1/10W
R1657 1-216-833-11 METAL CHIP10K5%1/10W
R1658 1-216-809-11 METAL CHIP1005%1/10W
R1659 1-216-833-11 METAL CHIP10K5%1/10W
R1660 1-216-833-11 METAL CHIP10K5%1/10W
R1662 1-216-827-11 METAL CHIP3.3K5%1/10W
R1663 1-216-827-11 METAL CHIP3.3K5%1/10W
R1664 1-216-809-11 METAL CHIP1005%1/10W
R1665 1-216-809-11 METAL CHIP1005%1/10W
R1666 1-216-821-11 METAL CHIP1K5%1/10W
(DE595)
R1666 1-216-864-11 METAL CHIP05%1/10W
(DE495)
R1667 1-216-821-11 METAL CHIP1K5%1/10W
R1668 1-216-833-11 METAL CHIP10K5%1/10W
(DE495)
R1669 1-216-833-11 METAL CHIP10K5%1/10W
R1670 1-216-833-11 METAL CHIP10K5%1/10W
R1671 1-216-825-11 METAL CHIP2.2K5%1/10W
(DE495)
R1671 1-216-864-11 METAL CHIP05%1/10W
(DE595)
R1672 1-216-841-11 METAL CHIP47K5%1/10W
(DE495)
R1673 1-216-809-11 METAL CHIP1005%1/10W
R1674 1-216-809-11 METAL CHIP1005%1/10W
R1676 1-216-821-11 METAL CHIP1K5%1/10W
R1677 1-216-821-11 METAL CHIP1K5%1/10W
R1678 1-216-821-11 METAL CHIP1K5%1/10W
R1679 1-216-821-11 METAL CHIP1K5%1/10W
R1681 1-216-833-11 METAL CHIP10K5%1/10W
(DE495)
R1682 1-216-845-11 METAL CHIP100K5%1/10W
R1683 1-216-833-11 METAL CHIP10K5%1/10W
R1684 1-216-833-11 METAL CHIP10K5%1/10W
R1685 1-216-833-11 METAL CHIP10K5%1/10W
R1686 1-216-833-11 METAL CHIP10K5%1/10W
R1687 1-216-833-11 METAL CHIP10K5%1/10W
R1688 1-216-864-11 METAL CHIP05%1/10W
R1689 1-216-833-11 METAL CHIP10K5%1/10W
R1690 1-216-833-11 METAL CHIP10K5%1/10W
R1694 1-216-821-11 METAL CHIP1K5%1/10W
R1698 1-216-829-11 METAL CHIP4.7K5%1/10W
R1699 1-216-829-11 METAL CHIP4.7K5%1/10W
R1703 1-216-833-11 METAL CHIP10K5%1/10W
R1704 1-216-833-11 METAL CHIP10K5%1/10W
R1705 1-216-809-11 METAL CHIP1005%1/10W
(AEP,UK)
R1706 1-216-833-11 METAL CHIP10K5%1/10W
R1707 1-216-833-11 METAL CHIP10K5%1/10W
R1708 1-216-833-11 METAL CHIP10K5%1/10W
R1709 1-216-833-11 METAL CHIP10K5%1/10W
(MULTI CHANNEL DECODING) (DE595)
D1028-719-046-39 LED SEL5821A-TP15 (MUSIC)
D1038-719-046-39 LED SEL5821A-TP15 (MOVIE)
D1048-719-046-39 LED SEL5821A-TP15 (A.F.D.)
D1058-719-046-39 LED SEL5821A-TP15 (2CH)
< FLUORESCENT INDICATOR >
FL1011-518-831-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC1008-759-643-83 IC uPD16315GB-3BS
IC1018-759-036-90 IC MC74ACT08N
IC1026-600-055-01 IC GP1UD27SXK (R)
IC2016-703-501-01 IC M61527FP
IC4018-759-636-74 IC M5218AP-22
IC5018-749-011-16 IC STK350-230
IC6018-759-636-74 IC M5218AP-22
IC7016-700-943-01 IC uPC2581V-S
IC7026-700-943-01 IC uPC2581V-S
IC8018-759-649-68 IC uPC78M07AHF
IC8028-759-604-95 IC M5F79M07L
0 1031-696-847-11 CORD, POWER (AUS)
0 1031-769-079-22 CORD, POWER (KR)
0 1031-777-071-23 CORD, POWER (AEP,UK,E2,SP,MY)
0 1031-783-532-11 CORD, POWER (US,CND,MX,TW)
0 T9011-437-999-11 TRANSFORMER, POWER (DE495:AUS)
0 T9011-439-549-11 TRANSFORMER, POWER (DE595:US,MX)
0 T9011-439-550-11 TRANSFORMER, POWER
0 T9011-439-551-11 TRANSFORMER, POWER (DE595:SP,MY)
0 T9011-439-552-11 TRANSFORMER, POWER (DE595:TW)
0 T9011-439-553-11 TRANSFORMER, POWER (DE595:E2)
0 T9011-439-609-11 TRANSFORMER, POWER (DE595:CND)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
53
Page 54
STR-DE495/DE595
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.DateDescription of Revision
1.02003. 02New
1.12003. 04Argentine, Korean and Taiwan model addition.
54
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.