Sony STRDA-5300-ES Service manual

STR-DA5300ES

SERVICE MANUAL

Ver. 1.1 2007.10

This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.

** Manufactured under license from DTS, Inc.

“DTS”, “DTS-ES” and “Neo:6” are registered trademarks of DTS, Inc. and “DTS-HD Master Audio”, “DTS-HD High Resolution Audio” and “DTS 96/24” are trademarks of DTS, Inc.

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS (US model)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION:

With 8 ohm loads, both channels driven, from 20 − 20,000 Hz; rated 120 watts per channel minimum RMS power, with no more than

0.09% total harmon ic distortion from 250 milliwatts to rated output.

Amplifier section

POWER OUTPUT (US and Canadian models)

Rated Power Output at Stereo Mode

(8 ohms 20 Hz − 20 kHz, THD 0.09%): 120 W + 120 W

Reference Power Output a t St er eo Mode

(4 ohms 20 Hz − 20 kHz, THD 0.15%): 120 W + 120 W

Reference Power Outpu t

(8 ohms 1 kHz, THD 0.7%) FRONT 130 W + 130 W CENTER SURROUND 130 W + 130 W SURROUND BACK 130 W + 130 W

1) 2)

: 130 W

Reference Power Outpu t

Depending on the sound field settings and the source, there may be no sound output.

Measured under the following condit io ns: Power requirements: 120 V AC, 60 Hz

(AEP, Russian, Ukrainian and UK models) Rated Power Output at Stereo Mode

Reference Power Output at St ereo Mode

(4 ohms 1 kHz, THD 0.7%)

FRONT 120 W + 120 W CENTER SURROUND 120 W + 120 W SURROUND BACK 120 W + 120 W

(8 ohms 1 kHz, THD

0.7%): 125 W + 125 W

(4 ohms 1 kHz, THD

0.7%): 125 W + 125 W

: 120 W

1) 2)

US Model

Canadian Model

AEP Model

UK Model

Reference Power Outpu t

Reference Power Output at St er eo Mode

(8 ohms 20 Hz − 20 kHz, THD 0.09%)

FRONT 120 W + 120 W CENTER SURROUND 120 W + 120 W SURROUND BACK 120 W + 120 W

(4 ohms 20 Hz − 20 kHz, THD 0.15%) FRONT 120 W + 120 W CENTER SURROUND 120 W + 120 W SURROUND BACK 120 W + 120 W

(8 ohms 1 kHz, THD 10%): 150 W + 150 W

– Continued on next page –

: 120 W

9-887-741-02

MULTI CHANNEL AV RECEIVER

Sony Corporation

Home Audio Division Published by Sony Techno Create Corporation

STR-DA5300ES

Ver. 1.1

Reference Power Output at St er eo Mode

(4 ohms 1 kHz, THD 10%): 150 W + 150 W

Reference Power Outpu t

(8 ohms 1 kHz, THD 10%)

FRONT 150 W + 150 W CENTER 150 W SURROUND 150 W + 150 W SURROUND BACK

150 W + 150 W

Reference Power Outpu t

(4 ohms 1 kHz, THD 10%)

FRONT 150 W + 150 W CENTER 150 W SURROUND 150 W + 150 W SURROUND BACK

150 W + 150 W

Depending on the sound field settings and the source, there may be no sound output.

Measured under the followin g co nditions: Power requirements: 230 V AC, 50/60 Hz

(in countries/area in Europe other than t he U.K.) 240 V AC, 50/60 Hz (in the U.K. and general area)

Frequency response

PHONO RIAA equalization curve

MULTI CHANNEL INPUT, SA-CD/CD, MD/DAT, DVD/BD, T

V, SAT/ CATV, TAPE/CD-R, VIDEO 1/2/3

± 0.5 dB 10 Hz − 100 kHz

± 3 dB

Inputs (Analog)

PHONO Sensitivity: 2.5mV

MULTI CHANNEL INPUT, SA-CD/CD, MD/DA T, DVD/BD, TV, SAT/CATV, TAPE/CD-R, VIDEO 1/2/3

Impedance: 50kohms S/N: 90dB (A, 20 kHz LPF)

Sensitivity: 150mV Impedance: 50kohms S/N: 100dB (A, 20 kHz LPF)

Inputs (Digital)

DVD/BD, VIDEO 2, SA-CD/CD (Coaxial)

VIDEO 1, TV, SAT/CATV, TAPE/CDR, MD/DAT (Optical)

Impedance: 75ohms S/N: 96dB (A, 20 kHz LPF)

S/N: 96 dB (A, 20 kHz LPF)

Outputs

MD/DAT (REC OUT), VIDEO 1, ZONE 2, ZONE 3 (AUDIO OUT)

FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, SUB WOOFER

Voltage:150mV Impedance: 1kohm

Voltage: 2V Impedance: 1kohm

EQUALIZER

Gain levels ±10 dB, 1 dB step

FM tuner section

Tuning range 87.5 − 108.0 MHz Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals

75 ohms, unbalanced

AM tuner section

uning range

(US and Canadian models)

With 10-kHz tu ni ng scale

530 − 1,710 kHz

With 9-kHz tuning scale

531 − 1,710 kHz

(AEP, Russian, Ukrainian and UK models)

With 9-kHz tuning scale

531 − 1,602 kHz

Antenna (aerial) Loop antenna (aer ia l)

You can ch ange the AM tuning scale to either 9 kHz or 10 kHz. After tuning in any AM station, turn off the rece iver. While holding down TUNING MODE, press POWER on the recei ver. All preset stations will be erased when you change the tuning scale. To reset the scal e to 10 kHz (or 9 kHz), repeat the procedure.

Dimensions 430 × 175 × 430 mm

(width/height/depth) including projecting parts and controls

Mass (Approx.) 16.0 kg

Supplied accessories

Operating Instructions Quick Setup Guide (1) HDMI CONTROL Guide (1) GUI Menu List (1) Optimizer microphone ECM-AC1 (1) FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) AC power cord (main s l ead) (1) Remote commander RM-AAL008 (1) (US and

Canadian models) Remote commander RM-AAL009 (1) (AEP, Russian, Ukrainian and UK models) Remote commander RM-AAU016 (1)

R6 (size-AA) batteries (4)

Design and specifications are subject to change without notice.

Video section

Inputs/Outputs

Video: 1 Vp-p, 75 ohms COMPONENT VIDEO:

Y: 1 Vp-p, 75 ohms P

: 0.7 Vp-p, 75 ohms

B/CB

: 0.7 Vp-p, 75 ohms

R/CR

80 MHz HD Pass Through

HDMI Video

Input/Output (HDMI Repeater block)

640 × 480p@60Hz 720 × 480p@59.94/60Hz 1440 × 480p@59.94/60Hz (pixel sent 2times) 1280 × 720p@59.94/60Hz 1920 × 1080i@59.94/60Hz 1920 × 1080p@59.94/60Hz 720 × 576p@50Hz 1440 × 576p@50Hz (pixel sent 2times) 1280 × 720p@50Hz 1920 × 1080i@50Hz 1920 × 1080p@50Hz 1920 × 1080p@24Hz

General

Power requirements 120 V AC, 60 Hz (US and

Canadian models) 230 V AC, 50/60Hz (in countries/area in Europe other than the U.K.) 230 − 240V AC, 50/60Hz (in the U.K. and general area)

Power output (DIGITAL MEDIA PORT)

DC OUT:5 V, 700 mA

Power consumption 480 W/580 VA (US/

Canada) 480 W (AEP, Russian,

Ukrainian and UK models)

Power consumption (during standby mode)

0.7 W (when “HDM I Control” and “RS-232C Control” is set to “OFF”)

STR-DA5300ES

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA WT -540A. Follow the manuf acturers’ instructions to use these instruments.

2. A battery-operated A C milliammeter . The Data Precision 245 digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter . The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V A C range are suitable. (See Fig. A)

To Exposed Metal Parts on Set

0.15 µF

1.5 k

Ω

Earth Ground

voltmete (0.75 V)

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

LES COMPOSANTS IDENTIFIÉS P AR UNE MARQ UE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

À LA SÉCURITÉ!

1. SERVICING NOTES .............................................. 5

2. GENERAL .................................................................. 11

3. DISASSEMBLY

3-1. Disassembly Flow .......................................................... 19

3-2. Case ................................................................................ 20

3-3. SP-TM Board, Tuner (FM/AM) ..................................... 20

3-4. D-CONNECT Board, DSP Board, DIGITAL Board,

CIS Board and CONTROL Board.................................. 21

3-5. D-VIDEO Board............................................................. 21

3-6. Front Panel Section ........................................................ 22

3-7. S-VIDEO Board and A-VIDEO Board .......................... 22

3-8. FLI-1.8REG Board and ANALOG Board...................... 23

3-9. Power Transformer (T001), E-VOL Board and

MAIN Board................................................................... 24

3-10. Heat Sink Section ........................................................... 25

4. TEST MODE............................................................. 26

5. ELECTRICAL ADJUSTMENTS ........................ 30

6. DIAGRAMS

6-1. Block Diagram – CONTROL Section – .......................... 33

6-2. Block Diagram – DSP Section – ..................................... 34

6-3. Block Diagram – DIGITAL AUDIO Section – ............... 35

6-4. Block Diagram – HDMI Section (1/2) – ......................... 36

6-5. Block Diagram – HDMI Section (2/2) – ......................... 37

6-6. Block Diagram – VIDEO PROCESS Section – .............. 38

6-7. Block Diagram – ANALOG AUDIO Section – .............. 39

6-8. Block Diagram – POWER AMP Section – ..................... 40

6-9. Block Diagram – VIDEO Section (1/2) – ....................... 41

6-10. Block Diagram – VIDEO Section (2/2) – ....................... 42

6-11. Block Diagram – PANEL, CIS, XM/

SIRIUS RECEIVER, DMPORT Section – ..................... 43

6-12. Block Diagram – POWER SUPPLY Section –............... 44

6-13. Printed Wiring Board

– MAIN Board (Component Side) – ............................... 46

6-14. Printed Wiring Board

– MAIN Board (Conductor Side) – ................................. 47

6-15. Schematic Diagram – MAIN Board (1/4) – .................... 48

6-16. Schematic Diagram – MAIN Board (2/4) – .................... 49

6-17. Schematic Diagram – MAIN Board (3/4) – .................... 50

6-18. Schematic Diagram – MAIN Board (4/4) – .................... 51

6-19. Printed Wiring Board

– DIGITAL Board (Component Side) – .......................... 52

6-20. Printed Wiring Board

– DIGITAL Board (Conductor Side) –............................ 53

6-21. Schematic Diagram – DIGITAL Board (1/4) –............... 54

6-22. Schematic Diagram – DIGITAL Board (2/4) –............... 55

6-23. Schematic Diagram – DIGITAL Board (3/4) –............... 56

6-24. Schematic Diagram – DIGITAL Board (4/4) –............... 57

6-25. Printed Wiring Board – DSP Board (Side A) – ............... 58

6-26. Printed Wiring Board – DSP Board (Side B) – ............... 59

6-27. Schematic Diagram – DSP Board (1/4) – ....................... 60

6-28. Schematic Diagram – DSP Board (2/4) – ....................... 61

6-29. Schematic Diagram – DSP Board (3/4) – ....................... 62

6-30. Schematic Diagram – DSP Board (4/4) – ....................... 63

6-31. Printed Wiring Board

– ANALOG Board (Component Side) – ......................... 64

6-32. Printed Wiring Board

– ANALOG Board (Conductor Side) – ........................... 65

6-33. Schematic Diagram – ANALOG Board (1/3) – .............. 66

6-34. Schematic Diagram – ANALOG Board (2/3) – .............. 67

6-35. Schematic Diagram – ANALOG Board (3/3) – .............. 68

STR-DA5300ES

Ver. 1.1

6-36. Printed Wiring Board – E-VOL Board –......................... 69

6-37. Schematic Diagram – E-VOL Board (1/2) – ................... 70

6-38. Schematic Diagram – E-VOL Board (2/2) – ................... 71

6-39. Printed Wiring Boards – CONNECTOR Section –......... 72

6-40. Schematic Diagram – CONNECTOR Section – ............. 73

6-41. Printed Wiring Board

– TEMPERATURE DETECTION Board – .................... 74

6-42. Schematic Diagram

– TEMPERATURE DETECTION Board – .................... 74

6-43. Printed Wiring Board – A-CLASS AMP Board – ........... 75

6-44. Schematic Diagram – A-CLASS AMP Board (1/2) –..... 76

6-45. Schematic Diagram – A-CLASS AMP Board (2/2) –..... 77

6-46. Printed Wiring Board

– POWER AMPLIFIER Board – .................................... 78

6-47. Schematic Diagram – POWER AMPLIFIER Board –.... 79

6-48. Printed Wiring Board – PROTECTOR (F-C) Board – .... 80

6-49. Schematic Diagram – PROTECTOR (F-C) Board –....... 81

6-50. Printed Wiring Boards

– PROTECTOR (SB/SURR) Section – ........................... 82

6-51. Schematic Diagram

– PROTECTOR (SB/SURR) Section – ........................... 83

6-52. Printed Wiring Board – BIAS Board –............................ 84

6-53. Schematic Diagram – BIAS Board – .............................. 85

6-54. Printed Wiring Board – SP-TM Board – ......................... 86

6-55. Schematic Diagram – SP-TM Board – ............................ 87

6-56. Printed Wiring Board

– D-VIDEO Board (Component Side) – ......................... 88

6-57. Printed Wiring Board

– D-VIDEO Board (Conductor Side) – ........................... 89

6-58. Schematic Diagram – D-VIDEO Board (1/12) – ............ 90

6-59. Schematic Diagram – D-VIDEO Board (2/12) – ............ 91

6-60. Schematic Diagram – D-VIDEO Board (3/12) – ............ 92

6-61. Schematic Diagram – D-VIDEO Board (4/12) – ............ 93

6-62. Schematic Diagram – D-VIDEO Board (5/12) – ............ 94

6-63. Schematic Diagram – D-VIDEO Board (6/12) – ............ 95

6-64. Schematic Diagram – D-VIDEO Board (7/12) – ............ 96

6-65. Schematic Diagram – D-VIDEO Board (8/12) – ............ 97

6-66. Schematic Diagram – D-VIDEO Board (9/12) – ............ 98

6-67. Schematic Diagram – D-VIDEO Board (10/12) – .......... 99

6-68. Schematic Diagram – D-VIDEO Board (11/12) – ......... 100

6-69. Schematic Diagram – D-VIDEO Board (12/12) – ......... 101

6-70. Printed Wiring Board

– A-VIDEO Board (Component Side) – ........................ 102

6-71. Printed Wiring Board

– A-VIDEO Board (Conductor Side) – .......................... 103

6-72. Schematic Diagram – A-VIDEO Board (1/4) – ............. 104

6-73. Schematic Diagram – A-VIDEO Board (2/4) – ............. 105

6-74. Schematic Diagram – A-VIDEO Board (3/4) – ............. 106

6-75. Schematic Diagram – A-VIDEO Board (4/4) – ............. 107

6-76. Printed Wiring Board – S-VIDEO Board –.................... 108

6-77. Schematic Diagram – S-VIDEO Board – ....................... 109

6-78. Printed Wiring Board – VIDEO3 Board –...................... 110

6-79. Schematic Diagram – VIDEO3 Board – ........................ 111

6-80. Printed Wiring Board

– CONTROL Board (Component Side) – ...................... 112

6-81. Printed Wiring Board

– CONTROL Board (Conductor Side) –........................ 113

6-82. Schematic Diagram – CONTROL Board (1/2) – ........... 114

6-83. Schematic Diagram – CONTROL Board (2/2) – ........... 115

6-84. Printed Wiring Board – CIS Board –.............................. 116

6-85. Schematic Diagram – CIS Board – ................................ 117

6-86. Printed Wiring Board – DISPLAY Board – ................... 118

6-87. Schematic Diagram – DISPLAY Board – ...................... 119

6-88. Printed Wiring Boards – PANEL Section –.................... 120

6-89. Schematic Diagram – PANEL Section –........................121

6-90. Printed Wiring Board – DC-DC Board – ....................... 122

6-91. Schematic Diagram – DC-DC Board – .......................... 123

6-92. Printed Wiring Board – AC Board (TYPE A) – ............. 124

6-93. Printed Wiring Board – AC Board (TYPE B) – ............. 124

6-94. Schematic Diagram – AC Board – ................................. 125

7. EXPLODED VIEWS

7-1. Case Section ................................................................... 173

7-2. DIGITAL Board Section ................................................ 174

7-3. D-VIDEO Board Section................................................ 175

7-4. DISPLAY Board Section ................................................ 176

7-5. Front Panel Section ........................................................ 177

7-6. A-VIDEO Board Section................................................ 178

7-7. ANALOG Board Section ............................................... 179

7-8. Heat Sink Section ........................................................... 180

7-9. MAIN Board Section...................................................... 181

8. ELECTRICAL PARTS LIST............................... 182

Note 1:Refer “NOTE WHEN THE AC BOARD IS REPAIRED”

(page 5) in servicing notes for how to distinguish TYPE A/B.

Note 2:Refer to SUPPLEMENT -1 for the CONTROL, DIGITAL and

DSP boards of printed wiring boards, schematic diagrams and electrical parts list of Russian and Ukrainian models. When repairing the set of US, Canadian, AEP and UK models, refer to either of original service manual/SUPPLEMENT-1 according to the set.

SECTION 1

PART No.

– Back Panel –

SERVICING NOTES

STR-DA5300ES

Ver. 1.1

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

NOTE OF REPLACING THE IC3601 ON THE D-VIDEO BOARD

Replacement of IC3601 on the D-VIDEO board used in this set requires a special tool.

NOTE WHEN THE AC BOARD IS REPAIRED (US and Canadian models only)

Note: AEP, Russian, Ukrainian and UK models uses only TYPE B.

Two types exist in the AC board for US and Canadian models. Repair after distinguishing which type it is referring to the figure below.

– AC Board (Component Side) –

• MODEL IDENTIFICA TION

Model PART No.

US and Canadian models 3-113-954-1[] AEP model 3-113-954-2[] UK model 3-113-954-3[] Russian and Ukrainian models 3-113-954-4[]

NOTE OF REPLACING THE IC3511 AND IC3513 ON THE D-VIDEO BOARD

IC3511 and IC3513 on the D-VIDEO board cannot exchange with single. When IC3511 and IC3513 on the D-VIDEO board are damaged, exchange the entire mounted board.

NOTE OF REPLACING THE IC5002 AND IC5202 ON THE DSP BOARD

IC5002 and IC5202 on the DSP board cannot exchange with single. When IC5002 and IC5202 on the DSP board are damaged, exchange the entire mounted board.

JW003

TYPE A : JW003 is not mounted. TYPE B : JW003 is mounted.

STR-DA5300ES

UPDATE OF SOFTWARE OF IC2003 ON THE CONTROL BOARD, IC3610 ON THE D-VIDEO BOARD AND IC5208 ON THE DSP BOARD

Perform operation of the following when the update of software of the IC2003 on the CONTR OL board, IC3610 on the D-VIDEO board and IC5208 on the DSP board is necessary.

Connect:

J1499

for PC

Procedure:

1. Connect J1499 on the MAIN board and PC by using the RS-232C cable.

2. Turn on the main power.

3. The update is executed by using PC.

4. When the update ends, turn off the main power.

5. Remove the RS-232C cable from the J1499 on the MAIN board and PC.

ERROR MESSAGES

If there is a malfunction, the display shows a code of two numbers and a message. You can check the condition of the system by the message. Refer to the following table to solve the problem.

messages cause and response

PROTECTOR Irregular current is output to the speakers, or the upper panel of the receiver is covered with something.

The receiver will automatically turn off after a few seconds. Cheack the speakers connection and turn on the power again.

STR-DA5300ES

POWER AMP BLOCK SERVICE POSITION

In checking the Power AMP block, prepare jig (e xtension cable J-2501-291-A: 2 mm Pitch, 12 cores, Length 300 mm/J-2501-311-A: 2 mm Pitch, 15 cores, Length 300 mm).

A-CLASS AMP board

power AMP Block

insulating sheet

A-CLASS AMP board (CN1504)

(CN1505)

Connect the extension jig (J-2501-311-A) to the A-CLASS AMP board (CN1505) and CONNECTOR 1 board (CN1206).

CONNECTOR 2 board (CN1206)

Connect the extension jig (J-2501-291-A) to the A-CLASS AMP board (CN1504) and CONNECTOR 2 board (CN1207).

CONNECTOR 1 board (CN1207)

CONTROL BOARD SERVICE POSITION

In checking the CONTROL board, prepare jig (extension cable J-2501-255-A: 1.25 mm Pitc h, 10 cores, Length 300 mm/J-2501-258-A: 1.25 mm Pitch, 16 cores, Length 300 mm/J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-260-A: 1.25 mm Pitch, 20 cores, Length 300 mm).

connect jig (extension cable J-2501-260-A) to the CONTROL board (CN2006)

and MAIN board (CN1005). connect jig (extension cable J-2501-255-A) to the CONTROL board (CN2008) and MAIN board (CN1006).

CONTROL board (CN2008)

CONTROL board (CN2005)

CONTROL board (CN2006)

CONTROL board (CN2004)

insulating sheet

connect jig (extension cable J-2501-258-A) to the CONTROL board (CN2004) and D-CONNECT board (CN2403).

D-CONNECT board (CN2405)

connect jig (extension cable J-2501-259-A) to the CONTROL board (CN2005) and D-CONNECT board (CN2405).

D-CONNECT board (CN2403)

MAIN board (CN1005)

MAIN board (CN1006)

STR-DA5300ES

DIGITAL BOARD SERVICE POSITION

In checking the DIGITAL board, prepare jig (extension cable J-2501-312-A: 1.25 mm Pitch, 11 cores, Length 300 mm).

CONTROL board (CN2002)

connect jig (extension cable J-2501-312-A) to the DIGITAL board (CN2203) and CONTROL board (CN2002).

DIGITAL board (CN2203)

D-VIDEO/S-VIDEO BOARDS SERVICE POSITION

In checking the D-VIDEO board, prepare jig (extension cable J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-313-A: 1.25 mm Pitch, 17 cores, Length 300 mm).

Connect jig (extension cable J-2501-313-A) to the D-VIDEO board (CN3508) and CONTOL board (CN2009).

D-VIDEO board (CN3508)

D-VIDEO board (CN3507)

S-VIDEO board

Connect jig (extension cable J-2501-259-A) to the D-VIDEO board (CN3507) and CONTOL board (CN2001).

CONTROL board (CN2001)

CONTROL board (CN2009)

STR-DA5300ES

A-VIDEO BOARD SERVICE POSITION

In checking the A-VIDEO board, prepare jig (extension cable J-2501-257-A: 1.25 mm Pitch, 14 cores, Length 300 mm).

connect jig (extension cable J-2501-257-A) to the CONTROL board (CN2010) and A-VIDEO board (CN6507).

A-VIDEO board (CN6507)

CONTROL board (CN2010)

insulating sheet

ANALOG BOARD SERVICE POSITION

In checking the ANALOG board, prepare jig (extension cable J-2501-258-A: 1.25 mm Pitch, 16 cores, Length 300 mm).

connect jig (extension cable J-2501-258-A)

ANALOG board (CN602)

to the CONTROL board (CN2011) and ANALOG board (CN602).

CONTROL board (CN2011)

insulating sheet

STR-DA5300ES

MAIN BOARD SERVICE POSITION

CAUTION

C2490

C2491

In checking the board, make two capacitors discharge for electric shock prevention. (R: 800

Ω

C2491

C2490

MAIN board

/2W)

insulating sheet

LEAD WIRE SETTING

The lead wire must not come in contact with the transformer and the heat sink.

Please band together so that a primary side cable cannot touch a power transformer and heat sink.

transformer

heat sink

SECTION 2

GENERAL

Getting Started

Description and location of parts (US and Canadian models)

Front panel

STR-DA5300ES

This section is extracted from instruction manual.

Status of the POWER button

Off The receiver is turned off (in itial setting). Press POWER to turn the receiver on. You cannot turn the receiver on using the remote.

Name Function

A POWER Press to turn the

receiver on or off.

B AUTO CAL MIC

jack

C TONE MODE Adjusts FRONT/

TONE

D MEMORY/

ENTER TUNING MODE TUNING

E Remote sensor Receives signals from

F DIMMER Press repeatedly to

G DISPLAY Press repeatedly to

Connects to the supplied optimizer microphone for the Digital Cinema Auto Calibration function.

CENTER/ SURROUND/ SURROUND BACK BASS and TREBLE. Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level.

Press to operate a tuner (FM/AM) and satellite radio (XM/SIRIUS).

remote commander.

adjust brightness of the display.

select information displayed on the display.

To remove the cover

Press PUSH. When you remove the cover, keep it out of reach from children.

On/Standby Press the receiver on or set it to the standby mode. When you press POWER on the receiver, the receiver will be turned off.

Name Function

H SUR BACK

DECODING

I Display

window

J 2CH/A.DIRECT Press to select sound

A.F.D. MOVIE MUSIC

K ZONE/

POWER, SELECT

L DMPORT Press to select the

M HDMI Press to select input

Press to activate SB DECODING.

The current status of the selected component or a list of selectable items appears here.

field.

Press SELECT repeatedly to select zone 2, zone 3 or main zone. Each time you press POWER, the output signals for the selected zone will be turned on or off.

audio/video input signal from the component connected to the DIGITAL MEDIA PORT adapter.

source from the component connected to the HDMI IN jack.

?/1 on the remote to turn

Name Function

N PHONES jack Connects to

O SPEAKERS

(OFF/A/B/A+B)

P VIDEO 3 IN/

PORT ABLE AV IN jacks

Q MULTI

CHANNEL DECODING lamp

R INPUT

SELECTOR

S MASTER

VOLUME

headphones. Switch to OFF, A, B,

A+B of the front speakers.

Connect to a portable audio/video component such as a camcorder or video game.

Lights up when multichannel audio signals are decoded.

Turn to select the input source to play back. To select the input source for zone 2 or zone 3, press ZONE/ SELECT ( zone 2 or zone 3 first (“ZONE 2 INPUT” or “ZONE 3 INPUT” appears on the display), then turn INPUT SELECTOR to select the input source.

Turn to adjust the volume level of all speakers at the same time.

qa) to select

STR-DA5300ES

Rear panel

A DIGITAL INPUT/OUTPUT section

OPTICAL IN/ OUT jacks

COAXIAL IN jacks

HDMI IN/ OUT* jacks

Connect to a DVD player, Super Audio CD player, etc. The COAXIAL jack provides a better quality sound.

Connect to a DVD player, Blu-ray Disc Player, or a satellite tuner. An image and the sound are output to TV or a projector.

B Control jack for Sony equipment

and other external components

IR REMOTE IN/OUT jacks

TRIGGER OUT jacks

CTRL S IN/ OUT jacks

Connect an IR repeater.

Connect to interloc k on/off of the power supply of other 12V TRIGGER compliant components, or the amplifier/receiver of zone 2 or zone 3.

Connect to Sony TV , DVD player or VCR with CONTROL S jack.

D ANTENNA section

FM ANTENNA jack

AM ANTENNA jack

XM jack Connects to the XM

SIRIUS jack Connects to a

Connects to the FM wire antenna (aeria l) supplied with this receiver.

Connects to the AM loop antenna (aerial) supplied with this receiver.

Mini Tuner and Home Dock (not supplied).

SiriusConnect Home tuner (not supplied).

E COMPONENT VIDEO INPUT/

OUTPUT section

Y, PB/CB, PR/ C

IN/OUT*

jacks

Connect to a DVD player, TV, or a satellite tuner.

F RS-232C port

Used for maintenance and service.

H VIDEO/AUDIO INPUT/OUTPUT

section

AUDIO IN/ OUT jacks

VIDEO IN/ OUT* jacks

S VIDEO IN/ OUT* jacks

AUDIO OUT jacks VIDEO OUT jack

EXT VIDEO IN jack

Connect to a VCR or a DVD player etc..

Connect to the component in zone 2 or zone 3.

Connects to the component when you want to watch in PIP (Picture in Picture) window.

I SPEAKERS section

Connects to speakers.

C DMPORT

Connects to a Sony DIGITAL MEDIA PORT adapter.

G AUDIO INPUT/OUTPUT section

AUDIO IN/ OUT jacks

MULTI CHANNEL INPUT jacks

PRE OUT jacks Connect to an

Connect to a tape deck or MD deck, etc.

Connect to a Super Audio CD player or DVD player with an analog audio jack for

7.1 channel or 5.1 channel sound.

external power amplifier.

*You can watch the selected input image when you

connect the MONITOR VIDEO OUT jack to a TV. You can operate this receiver using a GUI (Graphical User Interface).

STR-DA5300ES

Remote commander

You can use the supplied remote RM-AAL008 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate.

RM-AAL008

Name Function

A AV ?/1 (on/

standby)

B ?/1 (on/

standby)

C Input

buttons

D ZONE 2

ZONE 3

E AMP Press to enable the receiver operation. F MUSIC Press to select sound field.

G MOVIE Press to select sound field.

Press to turn on or off the audio/video components that the remote is assigned to operate. If you press the ?/1 (B) at the same time, it will turn off the receiver and other Sony components (SYSTEM STANDBY).

Note

The function of the AV?/1 switch changes automatically each time you press the input button (C).

Press to turn the receiver on or off. If ZONE 2 or ZONE 3 is selected, only the main receiver is turned on or off with this button. To turn off all components including an amplifier in zone 2 or zone 3, press ?/1 and AV?/1 (A) at the same time (SYSTEM STANDBY).

Press one of the buttons to select the component you want to use. Press a pink-labeled button after pressing SHIFT

(wj). When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components. You can program the remote to control nonSony components following the steps in “Programming the remote”.

Press to enable the zone 2 or zone 3 operation.

Name Function

H Numeric

buttons

I ENTER Press to enter the value after selecting a

MEMORY Press to store a station during tuner

J AMP MENU Press to display the menu to operate the

V/v/B/b

L OPTIONS Press to display and select items from

TOOLS Press to display and select items from the

M MENU Press to display the menu to operate the

SCREEN/ DSPL CONTROL

N CATEGORY

+/–

O m/M

a) b)

H ./>

CATEGORY MODE

TUNING +/– Press to select station.

P PRESET

/–

+ TV CH +/– Press TV (wk), then press TV CH+/− to

Q F1/F2 Press TV (wk), then press F1 or F2 to

MACRO1, MACRO2

TV/INPUT Press TV/INPUT and TV (wk) at the

WIDE Press repeatedly to select the wide picture

PIP Press SHIFT (wj), then press PIP to

RESOLUTION

Press to

− preset/tune to preset stations.

− select track numbers of the CD player,

DVD player, Blu-ray Disc Player or MD deck. Press 0/10 to select track number 10.

− select channel numbers of the VCR or satellite tuner.

− After pressing TV (wk), press the numeric buttons to select the TV channels.

channel, disc or track using the numeric buttons.

operation.

receiver. Press V/v/B/b to select the menu items.

Then press

option menus for receiver and DVD player, Blu-ray Disc Player.

option menus for DVD player or Blu-ray Disc Player, etc.

audio/video components. Press SHIFT (wj), then press MENU to

switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window).

Press to select the category for satellite tuner.

Press to operate the DVD player, Blu-ray Disc Player, CD player, MD deck, tape deck, or component connected to the DIGITAL MEDIA PORT adapter etc.

Press to select the category mode for satellite tuner.

Press to register FM/AM/satellite tuner stations or to select preset stations.

operate the TV, satellite tuner, VCR, etc.

select a component to operate.

• HDD recorder

F1: HDD F2: DVD player, Blu-ray Disc Player

• DVD/VHS combo player

F1: DVD player, Blu-ray Disc Player F2: VHS

Press AMP (5), then press MACRO 1 or MACRO 2 to set up the macro function.

same time to select the input signal (TV input or video input).

mode.

switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (qa). You can also move the window position using V/v/B/b (qa).

Note

The HDMI video signals are not output while the PIP window is displayed.

Press SHIFT (wj), then press RESOLUTION repeatedly to change the resolution of signals output from the HDMI OUT or COMPONENT VIDEO MONITOR OUT jack.

to enter the selection.

Name Function

R DVD/

TOP MENU, MENU

NIGHT MODE

INPUT MODE

SLEEP Press SHIFT (wj), then press SLEEP to

TEST TONE Press SHIFT (wj), then press TEST

S MUTING Press to turn off the sound temporarily.

T MASTER

VOL +/– TV VOL +/– Press TV (wk), then press TV VOL +/−

U DISC SKIP Press to skip a disc when using a

V RETURN/

EXIT O

W DISPLAY Press to select information displayed in

X CLEAR Press to

>10 Press to select

D.TUNING Press to enter direct tuning mode.

Y 2CH/

A.DIRECT

Z A.F.D. Press to select sound field.

wj SHIFT Press to light up the button. It changes the

wk TV Press to enable the TV operation. wl RM SET UP Press to set up the remote.

See the table for information on the buttons that you can use to control each component.

The tactile dot is attached to these buttons (H, PRESET+). Use as a mark of operation.

Press to display the menus of the DVD player on the TV screen. Then use V/v/B/b and operations.

Press AMP (5), then press NIGHT MODE to activate the NIGHT MODE function.

Press AMP (5), then press INPUT MODE to select the input mode when the same components are connected to both digital and analog jacks.

activate the sleep timer function and the duration which the receiver turns off automatically.

TONE to output the test tone from each speaker.

Press the button again to restore the sound. Press to adjust the volume level of all

speakers at the same time.

to adjust the volume level of the TV.

multi-disc changer. Press to return to the previous menu or

exit the menu while the menu or on-screen guide of the VCR, DVD player, or satellite tuner is displayed on the TV screen.

the display window, TV screen of the VCR, satellite tuner, CD player, DVD player, Blu-ray Disc Player, or MD deck.

Note

In the SCREEN mode, press the button to display the menu on the TV screen.

− clear a mistake when you press the incorrect numeric button.

− return to continuous playback, etc. of the satellite tuner or DVD player.

− track numbers over 10 of the VCR, satellite tuner, CD player or MD deck.

− channel numbers of the Digital CATV terminal.

Press to select sound field or to switch the audio of the selected input to analog signal without any adjustment.

remote button function to activate the buttons with pink printing.

to perform a menu

Notes

•Some functions explained in this section may not work depending on the model.

•The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

STR-DA5300ES

RM-AAU016

This remote can only be used to operate the receiver. You can control the main functions of the receiver with simple operations usin g this remote.

Name Function

A ?/1 (on/

standby)

B 2CH/

A.DIRECT A.F.D. MOVIE MUSIC

C SCREEN/

DSPL CONTROL

V/v/B/b

Press to turn a receiver on or off.

Press to select sound field.

Press to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window).

After pressing SCREEN/DSPL CONTROL (3), press V/v/B/ b to select the menu item. Then press to enter the selection.

Name Function

E OPTIONS Press to display and select items

F MENU Press to display the menu to

G DMPORT Press to operate the component

N Starts play. x Stops play. ./> Skips tracks.

H INPUT

SELECTOR

I MASTER

VOLUME +/–

J MUTING Press to turn off the sound

K RETURN/

EXIT

L DISPLAY Press to select information

M PIP Press PIP to switch the ima ge of

from option menus.

operate the receiver.

connected to the DIGITAL MEDIA PORT adapter.

Press to select the input source to play back.

Press to adjust the volume level.

temporarily. Press the button again to restore the sound.

Press to return to the previous menu or exit the menu.

displayed in the display window.

Note

In the SCREEN mode , press the button to display the menu on the TV screen.

the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (4). You can also move the window position using V/v/B/b (4).

Note

The HDMI video signals are not output while the PIP window is displayed.

STR-DA5300ES

Getting Started

Description and location of parts (AEP, Russian, Ukrainian and UK models)

Front panel

Ver. 1.1

Status of the POWER button

Off The receiver is turned off (in itial setting). Press POWER to turn the receiver on. You cannot turn the receiver on using the remote.

Name Function

A POWER Press to turn the

receiver on or off.

B AUTO CAL MIC

jack

C TONE MODE Adjusts FRONT/

TONE

D MEMORY/

ENTER TUNING MODE TUNING

E Remote sensor Receives signals from

F DIMMER Press repeatedly to

G DISPLAY Press repeatedly to

Connects to the supplied optimizer microphone for the Digital Cinema Auto Calibration function.

CENTER/ SURROUND/ SURROUND BACK BAS S and TREBLE. Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level.

Press to operate a tuner (FM/AM).

remote commander.

adjust brightness of the display.

select information displayed on the display.

To remove the cover

Press PUSH. When you remove the cov er, keep it out of reach from children.

On/Standby

/1 on the remote to turn

Press the receiver on or set it to the standby mode. When you press POWER on the receiver, the receiver will be turned off.

Name Function

H SUR BACK

DECODING

I Display

window

J 2CH/A.DIRECT Press to select sound

A.F.D. MOVIE MUSIC

K ZONE/

POWER, SELECT

L DMPORT Press to select the

M HDMI Press to select input

Press to activate SB DECODING.

The current status of the selected component or a list of selectable items appears here.

field.

Press SELECT repeatedly to select zone 2, zone 3 or main zone. Each time you press POWER, the output signals for the selected zone will be turned on or off.

audio/video input signal from the component connect ed to the DIGITAL MEDIA POR T adapter.

source from the component connect ed to the HDMI IN jack.

Name Function

N PHONES jack Connects to

headphones.

O SPEAKERS

(OFF/A/B/A+B)

P VIDEO 3 IN/

PORT ABLE AV IN jacks

Q MULTI

CHANNEL DECODING lamp

R INPUT

SELECTOR

S MASTER

VOLUME

Switch to OFF, A, B, A+B of the front speakers.

Connect to a portable audio/video component such as a camcorder or video game.

Lights up when multichannel audio signal s are decoded.

Turn to adjust the volume level of all speakers at the same time.

) to select

STR-DA5300ES

Rear panel

A DIGITAL INPUT/OUTPUT section

OPTICAL IN/ OUT jacks

COAXIAL IN jacks

HDMI IN/ OUT* jacks

Connect to a DVD player, Super Audio CD player, etc. The COAXIAL jack provides a better quality sound.

Connect to a DVD player, Blu-ray Disc Player, or a satellite tuner. An image and the sound are output to TV or a projector.

B Control jack for Sony equipment

and other external components

IR REMOTE IN/OUT jacks

TRIGGER OUT jacks

CTRL S IN/ OUT jacks

Connect an IR repeater.

Connect to interloc k on/off of the power supply of other 12V TRIGGER compliant components, or the amplifier/receiver of zone 2 or zone 3.

Connect to Sony TV , DVD player or VCR with CONTROL S jack.

C DMPORT

Connects to a Sony DIGITAL MEDIA PORT adapter.

D COMPONENT VIDEO INPUT/

OUTPUT section

Y, PB/CB, PR/ C

IN/OUT*

jacks

Connect to a DVD player, TV, or a satellite tuner.

E ANTENNA section

FM ANTENNA jack

AM ANTENNA jack

Connects to the FM wire antenna (aeria l) supplied with this receiver.

Connects to the AM loop antenna (aerial) supplied with this receiver.

F RS-232C port

Used for maintenance and service.

G AUDIO INPUT/OUTPUT section

AUDIO IN/ OUT jacks

MULTI CHANNEL INPUT jacks

PRE OUT jacks Connect to an

Connect to a tape deck or MD deck, etc.

Connect to a Super Audio CD player or DVD player with an analog audio jack for

7.1 channel or 5.1 channel sound.

externa l power amplifier.

H VIDEO/AUDIO INPUT/OUTPUT

section

AUDIO IN/ OUT jacks

VIDEO IN/ OUT* jacks

S VIDEO IN/ OUT* jacks

AUDIO OUT jacks VIDEO OUT jack

EXT VIDEO IN jack

Connect to a VCR or a DVD player etc..

Connect to the component in zone 2 or zone 3.

Connects to the component when you want to watch in PIP (Picture in Picture) window.

I SPEAKERS section

Connects to speakers.

*You can watch the selected input image when you

connect the MONITOR VIDEO OUT jack to a TV. You can operate this receiver using a GUI (Graphical User Interface).

STR-DA5300ES

Remote commander

You can use the supplied remote RM-AAL009 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate.

RM-AAL009

Name Function

A AV ?/1 (on/

standby)

B ?/1 (on/

standby)

C Input

buttons

D ZONE 2

ZONE 3

E AMP Press to enable the receiver operation. F MUSIC Press to select sound field.

Press to turn on or off the audio/video components that the remote is assigned to operate.

If you press the ?/1 (B) at the same time, it will turn off the receiver and other Sony components (SYSTEM STANDBY).

Note

The function of the AV?/1 switch changes automatically each time you press the input button (C).

press ?/1 and AV?/1 (A) at the same time (SYSTEM STANDBY).

Saving the power in standby mode.

When “HDMI Control” and “RS-232C Control” are set to “OFF.”

Press one of the buttons to select the component you want to use. Press a pink-labeled button after pressing SHIFT

(wj). When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony

components. You can program the remote to control non-Sony components following the steps in “Programming the remote”.

Press to enable the zone 2 or zone 3 operation.

Name Function Name Function

G MOVIE Press to select sound field. H Numeric

buttons

I ENTER Press to enter the value after selecting a

MEMORY Press to store a station during tuner

J AMP MENU Press to display the menu to operate the

V/v/B/b

L OPTIONS Press to display and select items from

TOOLS Press to display and select items from the

M MENU Press to display the menu to operate the

SCREEN/ DSPL CONTROL

N B·/·b Press to select the album.

O m/M

a) b)

H ./>

TUNING +/– Press to select station.

P PRESET

/–

+ TV CH +/– Press TV (wk), then press TV CH+/− to

Q F1/F2 Press TV (wk), then press F1 or F2 to

MACRO1, MACRO2

TV/INPUT Press TV/INPUT and TV (wk) at the

WIDE Press repeatedly to select the wide picture

PIP Press SHIFT (wj), then press PIP to

RESOLUTION

Press to

− preset/tune to preset stations.

− select track numbers of the CD player,

DVD player, Blu-ray Disc Player or MD deck. Press 0/10 to select track number 10.

− select channel numbers of the VCR or satellite tuner.

− After pressing TV (wk), press the numeric buttons to select the TV channels.

channel, disc or track using the numeric buttons.

operation.

receiver. Press V/v/B/b to select the menu items.

Then press to enter the selection.

option menus for receiver and DVD player, Blu-ray Disc Player.

option menus for DVD player or Blu-ray Disc Player, etc.

audio/video components. Press SHIFT (wj), then press MENU to

switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window).

Press to operate the DVD player, Blu-ray Disc Player, CD player, MD deck, tape deck, or component connected to the

DIGITAL MEDIA PORT adapter etc.

Press to register FM/AM Radio station or to select preset stations.

operate the TV, satellite tuner, VCR, etc.

select a component to operate.

• HDD recorder

F1: HDD F2: DVD player, Blu-ray Disc Player

• DVD/VHS combo player

F1: DVD player, Blu-ray Disc Player F2: VHS

Press AMP (5), then press MACRO 1 or MACRO 2 to set up the macro function.

same time to select the input signal (TV input or video input).

mode.

switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t

ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the

(qa). You can expand or shrink the window using V/v (qa). You can also change the window’s position using B/b

(qa).

Note

The HDMI video signals are not output while the PIP window is displayed.

Press SHIFT (wj), then press RESOLUTION repeatedly to change the resolution of signals output from the HDMI OUT or COMPONENT VIDEO MONITOR OUT jack.

R DVD/

TOP MENU, MENU

NIGHT MODE

INPUT MODE

SLEEP Press SHIFT (wj), then press SLEEP to

TEST TONE Press SHIFT (wj), then press TEST

S MUTING Press to turn off the sound temporarily.

T MASTER

VOL +/– TV VOL +/– Press TV (wk), then press TV VOL +/−

U DISC SKIP Press to skip a disc when using a

V RETURN/

EXIT O

W DISPLAY Press to select information displayed in

X CLEAR Press to

>10 Press to select

D.TUNING Press to enter direct tuning mode.

Y 2CH/

A.DIRECT

Z A.F.D. Press to select sound field.

wj SHIFT Press to light up the button. It changes

wk TV Press to enable the TV operation. wl RM SET UP Press to set up the remote.

See the table for information on the buttons that you can use to control each component.

The tactile dot is attached to these buttons (H, PRESET+). Use as a mark of operation.

Notes

•Some functions explained in this section may not work depending on the model.

•The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

Press to display the menus of the DVD player on the TV screen. Then use V/v/B/b and

operations. Press AMP (5), then press NIGHT

MODE to activate the NIGHT MODE function.

Press AMP (5), then press INPUT MODE to select the input mode when the same components are connected to both digital and analog jacks.

activate the sleep timer function and the duration which the receiver turns off.

TONE to output the test tone from each speaker.

Press the button again to restore the sound.

Press to adjust the volume level of all speakers at the same time.

to adjust the volume level of the TV.

multi-disc changer. Press to return to the previous menu or

exit the menu while the menu or on-screen menu or on-screen guide of the VCR, DVD player, or satellite tuner is displayed displayed on the TV screen.

the display window, TV screen of the VCR, satellite tuner, CD player, DVD player, Blu-ray Disc Player, or MD deck.

Note

In the SCREEN mode, press the button to display the menu on the TV screen.

− clear a mistake when you press the incorrect numeric button.

− return to continuous playback, etc. of the satellite tuner or DVD player.

− track numbers over 10 of the VCR, satellite tuner, CD player or MD deck.

− channel numbers of the Digital CATV terminal.

Press to select sound field or to switch the audio of the selected input to analog signal without any adjustment.

the remote button function to activate the buttons with pink printing.

to perform a menu

STR-DA5300ES

RM-AAU016

This remote can only be used to operate the receiver . You can control the main functions of the receiver with simple operations usin g this remote.

Name Function

A ?/1 (on/

standby)

B 2CH/

A.DIRECT A.F.D. MOVIE MUSIC

C SCREEN/

DSPL CONTROL

V/v/B/b

Press to turn a receiver on or off.

Press to select sound field.

Press to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window).

After pressing SCREEN/DSPL CONTROL (3), press V/v/B/ b to select the menu item. Then press to enter the selection.

Name Function

E OPTIONS Press to display and select items

F MENU Press to display the men u to

G DMPORT Press to operate the component

N Starts play. x Stops play. ./> Skips tracks.

H INPUT

SELECTOR

I MASTER

VOLUME +/–

J MUTING Press to turn off the sound

K RETURN/

EXIT

L DISPLAY Press to select information

M PIP Press PIP to switch the image of

from option menus.

operate the receiver.

connected to the DIGITAL MEDIA PORT adapter.

Press to select the input source to play back.

Press to adjust the volume level.

temporarily. Press the button again to restore the sound.

Press to return to the previous menu or exit the menu.

displayed in the display window.

Note

In the SCREEN mod e, press the button to display the menu on the TV screen.

Note

The HDMI video signals are not output while the PIP window is displayed.

SECTION 3

DISASSEMBLY

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.

SET

3-2. CASE

(Page 20)

STR-DA5300ES

3-3. SP-TM BOARD,

TUNER (FM/AM) (Page 20)

3-9. POWER TRANSFORMER (T001),

3-4. D-CONNECT BOARD,

3-5. D-VIDEO BOARD

3-7. S-VIDEO BOARD AND

3-8. FLI-1.8REG BOARD

E-VOL BOARD AND MAIN BOARD (Page 24)

DSP BOARD, DIGITAL BOARD, CIS BOARD AND CONTROL BOARD (Page 21)

(Page 21)

A-VIDEO BOARD (Page 22)

AND ANALOG BOARD (Page 23)

3-6. FRONT PANEL SECTION

(Page 22)

3-10. HEART SINK SECTION

(Page 25)

STR-DA5300ES

Ver. 1.1

Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE

flat head screw

two screws (BVST4 BVTT4

8 (for black),

8 (for silver))

(TP)

two flat head screws (TP)

case

two screws (BVST4 BVTT4

8 (for black),

8 (for silver))

3-3. SP-TM BOARD, TUNER (FM/AM)

tuner (FM/AM)

clamp

SP-TM board

clamp

four connectors (CX4101, CX4102 CX4103, CX4104)

clamp

two screws (BVTT2.6

two screws (BV/ring)

wire (flat type) (9 core) (US and Canadian models), wire (flat type) (11 core) (AEP, Russian, Ukrainian and UK models) (tuner (FM/AM))

STR-DA5300ES

DIGITAL board

bracket (AC)

connector (CN2203)

connector (CN5001)

D-CONNECT board

DSP board

two screws (BVTP3

eight screws (BVTP3

two screws (BVTP3

screw (BVTP3 × 8)

two screws (BVTP3

four screws (BVTP3

two connectors (CN2204, CN2207)

CIS board

CONTROL board

three connectors (CN2012, CN2013, CN2014)

connector (CN2002)

six connectors

(CN2401, CN2402, CN2403,

CN2404, CN2405, CN2406)

)

Ver. 1.1

3-4. D-CONNECT BOARD, DSP BOARD, DIGITAL BOARD, CIS BOARD AND CONTROL BOARD

3-5. D-VIDEO BOARD

(AEP, Russian, Ukrainian UK models)

two clamps

(US and Canadian models)

clamp

screw (BVTP3

bracket (HDMI

D-VIDEO board

screw (BVTP3

five connectors (CN3509, CN3523, CN3605, CN3611, CN3902)

two screws (BV3)

seven screws (B3

STR-DA5300ES

3-6. FRONT PANEL SECTION

two clamps

connector (CNP53)

connector (CN606)

connector (CN6904)

five screws (BVTP3

3-7. S-VIDEO BOARD AND A-VIDEO BOARD

S-VIDEO board

two connectors (CN6518, CN6519)

four screws (BVTP3

two screws (BVTP3

front panel section

clamp

connector (CN6904)

seven screws (BVTP3

wire (flat type) (21 core) (S-VIDEO board (CN6903), A-VIDEO board (CN6509))

A-VIDEO board

3-8. FLI-1.8REG BOARD AND ANALOG BOARD

screw (BVTP3

bracket (side)

FLI-1.8REG board

bracket (WB)

connector (CN608)

two screws (BVTP3

STR-DA5300ES

Ver. 1.1

wire (flat type) (9 core) (US and Canadian models) (CN609), wire (flat type) (11 core)

(AEP, Russian, Ukrainian and UK models) (CN603)

ANALOG board

two connectors (CN601, CN1003)

screws (BVTP3

six screws

(BVTP3

connector (CN606)

screw (B3

(US and Canadian models)

connector (CN727)

STR-DA5300ES

3-9. POWER TRANS FORMER (T001), E-VOL BOARD AND MAIN BOARD

CONNECTOR 1 board

connector (CN1402)

four screws (BVTT4

CONNECTOR 2 board

two connectors (CN1205, CN1206)

E-VOL board

two screws (BVTP3

two connectors (CN1203, CN1204)

connector (CNP02)

bracket (SS)

wire (E-VOL board (CN1208), MAIN board (CN1206))

five screws (BVTP3

two connectors (CN1207, CN1209)

two screws

(BVTP3

bracket (SS)

wire (E-VOL board (CN1209), MAIN board (CN1205))

two wires (CN1001, CN1004)

MAIN board

power transformer (T001)

two connectors (CN1403, CN1408)

three screws (BV/ring)

four screws (BVTP3

feeder fixed screw

two screws (supllied with J1499)

3-10. HEAT SINK SECTION

three screws (BVTP3

four screws (BVTP3

heart sink section

STR-DA5300ES

CONNECTOR 2 board

two connectors (CN1205, CN1206)

CONNECTOR 1 board

two connectors (CN1207, CN1209)

connector (CN1405)

STR-DA5300ES

SECTION 4

TEST MODE

MEMORY CLEARING MODE

All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair.

Procedure:

1. While pressing the [TONE MODE] and [DMPORT] buttons, press the [POWER] button to turn on the main power.

2. The message “MEMORY CLEARING***” appears and the memories are reset to the default values.

3. When done, the message “MEMOR Y CLEARED*” appears.

FLUORESCENT INDICATOR TUBE PATTERN CHECK MODE

All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another.

Procedure:

1. While pressing the [MOVIE] and [DMPORT] buttons, press the [POWER] button to turn on the main power.

2. All segments and all LEDs turn on.

SOUND FIELD CLEAR MODE

The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair.

Procedure:

1. While pressing the [MUSIC] button, press the [POWER] button to turn on the main power.

2. The message “S. F. Initialize” appears and initialization is performed.

TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE (US and Canadian models only)

Either the 9 kHz step or 10 kHz step can be selected for the AM channel step.

Procedure:

1. Press the [POWER] button to turn on the main power.

2. Turn the [INPUT SELECTOR] dial to select the “AM”.

3. Press the [POWER] button to turn off the main power.

4. While pressing the [TUNING MODE] button, press the [POWER] button to turn on the main power.

5. Either the message “AM 9kHz Step” or “AM 10kHz Step” appears, select the desired step.

COMMAND MODE CHANGE MODE

The command mode of the remote-commander which this set receives can be changed.

Procedure:

1. While pressing the [2CH/A. DIRECT] button, press the [POWER] button to turn on the main power.

2. Either the message “COMMAND MODE [AV1]” or “COMMAND MODE [AV2]” appears. Select the desired mode.

SF LOCK ON/OFF CHANGE MODE

Procedure:

1. While pressing the [MUSIC] and [DMPORT] buttons, press the [POWER] button to turn on the main power.

2. Either the message “SF LOCK [OFF]” or “SF LOCK [ON]” appears.

XM FACTORY TEST MODE (US and Canadian models only)

Mode to confirm operation of XM. Doing display of ID of XM antenna and output of audio signal that XM antenna generates, it is confirmed that there are no problems in the communication of the XM antenna and the tranmission of the audio signal.

Procedure:

1. The XM antenna was connected, while pressing the [TUNING MODE] and [MOVIE] buttons, press the [POWER] button to

turn on the main power.

2. Whenever the [DISPLAY] button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1kHz R are switched.

SIRIUS FACTORY TEST MODE (US and Canadian models only)

Mode to confirm operation of SIRIUS. Doing display of ID of SIRIUS antenna and output of audio signal that SIRIUS antenna generates, it is confirmed that there are no problems in the communication of the SIRIUS antenna and the tranmission of the audio signal.

Procedure:

1. The SIRIUS antenna was connected, while pressing the [TUNING MODE] and [A.F.D.] buttons, press the [POWER] button to turn on the main power.

2. Whenever the [DISPLAY] button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1 kHz R are switched.

DIGITAL MEIDA PORT TEST

Procedure:

1. Connect the DMPORT check jig (P/N: J-2501-309-A) with the DMPORT jack (CN6505) on the A-VIDEO board.

2. While pressing the [A.F.D.] and [DMPORT] buttons, press the [POWER] button to turn on the main power.

3. The message “DMPORT OK.” appears on the fluorescent indicator tube and enter the digital media port test mode. (Confirmation of communication line) When “NO DETECT”, “UART NG” and “UART TO” are displayed on the fluorescent indicator tube, confirm the connection of the DMPORT check jig, and enter the mode again. Each time the > button on the remote commander is pressed, the connect check and adaptor version check are switched. Press the . button on the remote commander, connected confirmation of the DMPORT check jig is done again.

4. To a pinjack of the DMPORT check jig input information relevant to audio signal (sine-wave 1.0V rms) and composite video signal (white 100% 1.0Vp-p, color bar, etc.).

5. Confirm the output of speakers and monitor TV. (Confirmation of analog signal)

6. To exit from this mode, press the x button on the remote

color

pattern

generator

oscillator

J001

A-VIDEO board

CN6505

DMPORT

check jig

(Part No.:

J-2501-309-A)

A-VIDEO board

J6203

monitor

set

FL/FR

speaker

MAIN board

TM4002

HISTORY MODE

The state that the set is used is memorized.

Procedure:

1. While pressing the [MUSIC] and [MEMORY/ENTER] buttons, press the [POWER] button to turn on the power and “HIS- TORY MODE” is displayed.

2. Each time the M m key of remote commander is pressed, the item is switched in order as follows.

Items Display

Number of protector is generated PRCT COUNT: XXX Total use time TTL_TIME: XXXXH XXM Sound field setting XXXXXXXXXXXXXXXX Input when protect is detected INPUT: XXXXXXXXXX Input mode setting INMODE: XXXXXXXXXXXX Input mode under lick state DSEL: XXXXXXXXXXXXXXX Stream under input STREAM: XXXXXXX Channel information CONFIG:XXXXXXX State of headphone HEAD PHONES: XXX Volume VOL: XXXdB

EQ setting value

Level collection value Lv SL/SR XXXX/XXXX each channel Lv CT/SW XXXX/XXXX

Total time of power on TTL_P_ON: XXXXH XXM

BASS: XXXdB TREB: XXXdB Lv FL/FR XXXX/XXXX

Lv BL/BR XXXX/XXXX

STR-DA5300ES

SPECIAL MENU MODE

Procedure:

1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order, the message “MENU SPECIALIZED!” appears.

2. Press the M m button of the remote commander, the message “<<< SPECIAL >>>” appears.

3. Press the , button of the remote commander, the item is appears.

4. Each time the M m button of the remote commander is pressed, the item is switched in order as follows. Some items can change the content. Display the cursor by pressing the , button of the remote commander, and changing the content by pressing the M m button of the remote commander, and fix the content by pressing the < button of the remote commander when you want to change the content of the item.

5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order again, the message “MENU SPECIALIZED OFF” appears.

Items Display Remark

Video factory menu <VIDEO FACTORY MENU> Menu mode to enter video calibration menu and DDR access check menu

If the [ENTER] button of the remote commander is pressed, entering the

menu, and operating two the following menu become possible Video calibration V.CALIBRATION START? Procedure: (Video factory menu) 1. “DVD” is selected by using [INPUT SELECTOR] dial.

2. Connect a color pattern generator to the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) on the AVIDEO board, DVD/BD VIDEO IN jack (J6201) on the A-VIDEO board, DVD/BD S VIDEO IN jack (J6901) on the S-VIDEO board and EXT VIDEO IN jack (J6904).

3. Input 100% color bars signal from the color pattern generator.

4. Menu that measures individual difference of hardness by automatic operation in pressing the [ENTER] button of the remote commander, and corrects reference value. In a measurement once, only one of NTSC/PAL/HD can be measured

“Check XXXX V-IN” at display: Video signal necessary for the measurement while measuring it last time was not detected and it became an error

Confirm the input of the video of the terminal connection etc. , and measure the [ENTER] button of the remote commander again pressing

DDR access check DDR CHECK [XX] sec XX: Time to do access check on DDR (for design evaluation) (Video factory menu) Auto cal mic test SPEAKER OUT [XXXXX] XXXXX: Selection of speaker output audio

[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from

speaker FL display fonts test FL FONT [0x ** = X] **: 20 to FE, X: character FL display test ALL ON Each time DISPLAY button to change as follows

all on t test pattern 1 t test pattern 2 t all off t all on HDCP key read HDCP KEY READ [XXX] XXX: ON or OFF DSP SRAM check <DSP SRAM CHECK> XX: OK or NG

[ENTER] button of the remote OK: success access SRAM, NG: fail access to SRAM

commander

SRAM1 [XX] SRAM2 [XX] FAROUDJA update FAROUDJA UPDATE [XXX] XXX: ON or OFF Model version display ##### *** vX. XX @@@@ #####: Model

***: Destination X.XX: System controller software version

@@@@: Sum value of flash memory in the system controller Video Ucom version display Video Ucom Ver X. XX X.XX: Video system controller software version FAROUDJA version display FAROUDJA Ver X. XX X.XX: Video Processor software version GUI CG-ROM version display GUI CGROM Ver X. XX X.XX: CG-ROM software version DSP Ucom version display DSP Ucom Ver X. XX X.XX: DSP controller version DSP serial flash version display DSP SFLASH Ver X. XX X.XX: Serial flash software version DSP parallel flash version display DSP PFLASH Ver X. XX X.XX: DSP parallel flash version DSP halt DSP HALT [XXX] XXX: ON or OFF DSP RAM [*****]=XXXXXXXX Mode that refers to internal RAM of DSP (for design evaluation)

STR-DA5300ES

Items Display Remark

Super reset SUPER RESET [XXX] Not used for the servicing

If super reset is performed, “up convert signal level adjustment” will also be initialized When EEPROM initialization is required, perform the “memory clearing

mode” RAM watch menu XXX XXX: For monitor of various internal RAM (for design evaluation) EERROM debug EEPROM [****] [XX] ****: EEPROM address, XX: EEPROM data Protector on/off PROTECTOR ON/OFF [XXX] XXX: ON or OFF Model/destination change MODEL [##### * * * *] X X #####: Model, ****: Destination, XX: At or fx Audio swap SWAP [XXXXXXXXXXX] Switching with M m button of the remote commander Decoder select DECODER SEL [XXXX] XXXX: AUTO, LEGACY, DDPLUS, TRUEHD, DTSEXP, MP3SUR (for

debug) Volume value display (FL/FR) FL**** FR XXXX ****: Front L-ch volume value, XXXX: Front R-ch volume value Volume value display (SL/SR) SL**** SR XXXX ****: Surround L-ch volume value, XXXX: Surround R-ch volume value Volume value display (CT/SW) CT**** SW XXXX ****: Center volume value, XXXX: Sub woofer volume value Volume value display (SBL/SBR) SBL**** SBR XXXX ****: Surround back L-ch volume value, XXXX: Surround back R-ch

volume value DAC mute information disclosure 1 DAC MUTE U XXXXXXXX Display of module information to demand muting in system controller (for

design evaluation) DAC mute information disclosure 2 DAC MUTE L XXXXXXXX Display of module information to demand muting in system controller (for

design evaluation) 2nd volume value display 2nd VOLUME XXX XXX: 2nd room volume value (00 to ∞) FL display duty change DARK OUT DUTY [XXX%] XXX: Duty value of FL display (0% to 100%) DMPORT debug DMP KEY DEBUG [XXX] XXX: ON or OFF (for debug) Bus overflow debug HA link OVERFLOW HAL R [XX] XX: Counter of overflow receive buffer (receive) Bus overflow debug HA link OVERFLOW HAL S [XX] XX: Counter of overflow transmit buffer (transmit) Bus overflow debug DMPORT OVERFLOW CLA [XX] XX: Counter of overflow CLA transmit buffer

STR-DA5300ES

SECTION 5

ELECTRICAL ADJUSTMENTS

BIAS ALIGNMENT ADJUSTMENT

Note: Afer 10 minutes or more have passed since the power supply was

turned on, this adjustment is done.

Connection:

digital voltmeter

CN1561 (CN1611, CN1761, CN1861) pin CN1561 (CN1611, CN1761, CN1861) pin 2, CN1561 (CN1761, CN1861) pin

Note: Pin 3, 4 of CN1611 are open.

, CN1561 (CN1761, CN1861) pin

Procedure:

1. Connect a digital voltmeter to the CN1561 (CN1611, CN1761, CN1861).

2. Press the [POWER] button to turn on the main power.

3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751, RV1801, RV1851) so that the digital voltmeter reading is 5 mV to 20 mV.

Adjustment and Connection Location:

– BIAS Board (Conductor Side) –

Adjustment hole

for RV1801

(SBL)

Adjustment hole

for RV1851

(SBR)

Adjustment hole

for RV1601

(CENTER)

Adjustment hole

for RV1501

(F-L)

Adjustment hole

for RV1551

3 4

(F-R)

+ –

Adjustment hole

for RV1701

(SUR-L)

Adjustment hole

for RV1751

(SUR-R)

– PROTECTOR (SB) Board (Component Side) –

CN1861

– PROTECTOR (F-C) Board (Component Side) –

CN1611

CN1561

– PROTECTOR (SURR) Board (Component Side) –

CN1761

+ 230 hidden pages

Sony STRDA-5300-ES Service manual

TABLE OF CONTENTS

SERVICING NOTES

GENERAL

DISASSEMBLY

3-1. DISASSEMBLY FLOW

3-2. CASE

3-3. SP-TM BOARD, TUNER (FM/AM)

3-4. D-CONNECT BOARD, DSP BOARD, DIGITAL BOARD, CIS BOARD AND CONTROL BOARD

3-5. D-VIDEO BOARD

3-6. FRONT PANEL SECTION

3-7. S-VIDEO BOARD AND A-VIDEO BOARD

3-8. FLI-1.8REG BOARD AND ANALOG BOARD

3-9. POWER TRANS FORMER (T001), E-VOL BOARD AND MAIN BOARD

3-10. HEAT SINK SECTION

TEST MODE

ELECTRICAL ADJUSTMENTS