Page 1
Network Camera
SNC-RZ30N/2
SNC-RZ30P/2
Page 2
The High-Performance Network Camera With
Pan/Tilt/Zoom (PTZ) Delivering Outstanding Image
Quality – The Improved SNC-RZ30
*
1
Is the One!
Combining network functionality with a Pan/Tilt/Zoom (PTZ) capability, the SNC-RZ30 takes
applications such as remote monitoring, webcasting, etc. to the next step by offering the
flexibility to see almost anything within the camera's range and field-of-view over a TCP/IP
network. Images from the SNC-RZ30 can be viewed and the PTZ movement can be
controlled using a PC running a standard browser without the need for additional software.
Moreover, setup is very easy because the setup menu is also browser-based.
The SNC-RZ30 features a 25x optical zoom capability that allows a user to zoom in on small
or distant objects with exceptional clarity. Image quality is extremely high because the
SNC-RZ30 uses a newly improved high-resolution CCD imager and a high-quality image
processor. The SNC-RZ30 employs motion-JPEG compression and can be set up to transfer
these JPEG images to an FTP server or to a specified e-mail address. Also, the frame rate for
this camera can be set as high as 30 fps,
*
2
which makes for very smooth moving images.
The SNC-RZ30 features two built-in PC card slots to further expand the unit's memory with
removable media,
*
3
allowing you to store tens of thousands of images. In addition, the card
slot can accept IEEE 802.11b compliant wireless cards,
*
4
enabling the unit to be wirelessly
connected to a network.
Finally, unlike most network cameras, the SNC-RZ30 has an analog composite video output that
can be fed to a local video monitor or a video recorder, for viewing and redundant recording.
All of this functionality is packaged into one sleek, compact, and lightweight body that can
be either ceiling mounted or placed on a flat surface. Make the feature rich SNC-RZ30 the
camera for your network applications.
*1
Unless otherwise noted, "SNC-RZ30" in the following text refers to both the SNC-RZ30N/2 and SNC-RZ30P/2.
*2
The SNC-RZ30 offers a maximum frame rate of 30 fps while the SNC-RZ30P offers a maximum frame rate of 25 fps.
In order to achieve the maximum frame rate, a client PC with adequate processor speed and a network environment with
adequate bandwidth are required.
*3
Removable media can be a Flash ATA card, ATA HDD card, Memory Stick media card and Memory Stick/PC Card Adaptor,
all of which are not included.
*4
Please contact your local Sony sales office for a list of compatible wireless cards for use with the SNC-RZ30.
Page 3
High Frame Rate/Selectable
Parameters
The SNC-RZ30 also has a number of selectable
parameters that make it easy to match the
quality of the image with your bandwidth
requirements. For example, the SNC-RZ30,
which uses the industry-standard motion-JPEG
compression format, has a compression ratio
selectable between 1/5 and 1/60. Also, with a
maximum setting of 30 fps,
*2
the frame rate
can either be set manually at a fixed frame
rate, or at a variable frame rate based on the
amount of bandwidth available. Furthermore,
the resolution can be selected from a choice of
736 x 480,
*5
640 x 480, 320 x 240, and 160 x
120. With a high-speed network connection,
you can obtain high-quality video images, and
with a limited bandwidth connection, you can
set the parameters so that images are still very
clear with no image break-up.
*5
Resolution for the SNC-RZ30N is 736 x 480 while
resolution for the SNC-RZ30P is 736 x 544.
FEATURES
High-Quality Image
Employing a new Super HAD CCD, the
SNC-RZ30 delivers outstanding picture quality
even in low-light conditions for your remote
monitoring applications. The minimum
illumination level has been improved, providing
higher sensitivity as compared to the original
SNC-RZ30.
Desktop or Ceiling Mountable in a
Single Unit
A unique image flip function enables the
SNC-RZ30 to be either placed on a flat surface
or ceiling mounted – images are output rightside-up regardless of the orientation of the
unit. Unlike other products that require
separate models for ceiling and desktop
applications, this single model is all that is
necessary when installing your network camera
system saving you the hassle of ordering
multiple models.
New & Improved
New & Improved
Original CCD
Simulated images
New CCD
Page 4
High-Speed, Quiet Pan/Tilt/Zoom
(PTZ)
It's easy to locate almost any position in the
viewable area surrounding the SNC-RZ30 using
its high-speed PTZ capability. Of all PTZ-capable
network cameras, the SNC-RZ30 has one of the
widest ranges in its class: a pan range of 340°,
a tilt range of 115°, plus a 25x optical / 12x
digital zoom for a total zoom capability of
300x. The full 340° pan range can be covered
in 2 seconds, and the -90° to +25° tilt range
can be covered in 1.5 seconds. In addition to
the wide range of motion and high-speed
movements, the SNC-RZ30 incorporates
gearless direct-drive motors that ensure
exceptionally smooth and quiet operation.
Pan/Tilt Range
SNC-RZ30 Setting Menu
SNC-RZ30 Viewer
25x Optical Zoom (simulated images)
Remote Monitoring/Control Over
Networks Using a Standard Web
Browser
The SNC-RZ30 is equipped with a 100Base-TX
interface and has a built-in web server. This
allows the user to control the unit and view live
images over a network. All that is required is a
PC running a standard web browser;
*6
no
additional software is required.
*6
Requires Microsoft®Windows®98 or higher operating
system and Microsoft Internet Explorer 5.5 or higher web
browser.
Page 5
"Day/Night" Function
The SNC-RZ30 offers a "Day/Night" function to
provide optimized sensitivity in both day and
night environments. As the scene darkens, the
infrared cut-filter is automatically replaced with
a clear filter and the camera switches to B/W
mode, requiring a much lower minimum
illumination level. Three modes can be set:
automatic, manual, or timer mode.
Image Transfer Using FTP/SMTP
Because the SNC-RZ30 supports both FTP and
SMTP protocols, JPEG still image data can be
transferred, as required, either to an FTP server or
to a specified e-mail address as a JPEG attachment.
Activity Detection/Alarm Trigger
The SNC-RZ30 has a built-in activity detection
function that can be set to trigger its two
output relays. When there is movement in the
field-of-view of the camera, the camera can
trigger either or both of its relays to, for
example, set off an audible alarm, turn on a
lamp, or send a signal to an electric door strike
to lock or unlock a door. In addition to using
the built-in activity detection function, the
SNC-RZ30 can be configured with up to three
external sensors for expanded functionality.
These sensors can also be set to trigger the
camera's output relays, or to move the camera
to a preset position.
Moreover, other actions can be performed at
the time of an alarm event triggered by either
the activity detection function or an external
sensor. For example, sending the image that
was captured when the alarm was activated, to
an e-mail address or to an FTP server is possible.
Also, because the SNC-RZ30 has 8 MB of RAM
designated as a buffer and a high-speed datatransfer capability of up to 30 fps,
*7
hundreds of
images from before and after the alarm was
triggered can be buffered in the RAM and if
required transferred to an FTP server.
*7
The SNC-RZ30N transfers data at speeds up to 30 fps
while the SNC-RZ30P transfers data at speeds up to 25 fps.
Two Type II PC Card Slots
Two Type II PC card slots are integrated into the
SNC-RZ30, and can accept the following types
of PC cards:
*8
Memory Card
You can increase the SNC-RZ30 storage
capacity by adding either a flash memory card
or an ATA Hard Disk Drive (HDD) card. IC
recording media such as a Memory Stick™
media card with a Memory Stick/PC card
adaptor can also be used.
Wireless Card
Wireless networks are becoming more prevalent
allowing you to install your SNC-RZ30 without
unsightly wires. The SNC-RZ30 is compatible
with IEEE 802.11b compliant wireless PC cards.
*8
Please contact your local Sony sales office for a list of
compatible PC cards for use with the SNC-RZ30.
Analog Composite Video Output
The SNC-RZ30 can output an analog composite
video signal via the BNC connector on the
unit's rear panel.
*9
This is an ideal feature for
sending signals to a local recording device or
monitor.
*9
The SNC-RZ30N output is in NTSC format (525/60), and
the SNC-RZ30P output is in PAL format (625/50).
PCMCIA Type II x 2
Rear Panel
Page 6
Password Protection
User names and passwords can be assigned to
allow four levels of access. Generally,
the administrator has complete access/control of
the camera, while the other three levels can be
set to limit user privileges to functions such as
PTZ control, viewing, trigger control, etc.
Other Features
Viewing from a PDA
Images from the SNC-RZ30 can be viewed from
a PDA running Microsoft Pocket PC
®
2002.
*10
*10
The Jeode™ plug-in Ver. 1.9.1 is required for viewing
images from a PDA.
Direct Pointing or Vectoring
There is an alternative method of controlling the
pan and tilt of the SNC-RZ30. When this
alternate method is selected, an on-screen
simulated pad appears on the GUI (Graphical
User Interface) allowing "direct pointing" or
"vectoring" to control the camera.
"Tour" Feature
The "tour" feature allows the user to preset up
to five scanning patterns with up to 16 positions
in each scan. This is useful when you wish to
monitor designated areas in a room.
Cropping Feature
The administrator can designate an area in the
image to be cropped. This feature is particularly
useful when you wish to monitor a specific
location. In addition, it reduces the size of the
image file, making the storage and transfer of
images more efficient.
RS-232C/485 Interface (Transparency
Function or VISCA Protocol)
Transparency Function
The SNC-RZ30 has a transparency function
available via the RS-232C/485 interface. External
equipment can be connected and controlled by a
PC connected to the network on which the
SNC-RZ30 resides.
VISCA Protocol
The SNC-RZ30 can be interfaced with external
control equipment using the VISCA protocol.
This configuration allows for local control of
P/T/Z and camera settings.
Simultaneous Access
Up to 50 users can simultaneously access a
single SNC-RZ30 to monitor images and control
the camera. One of two control modes for the
camera can be set by the administrator,
allowing control of the unit to be shared by a
number of users. One mode gives priority to
the user who last attempted to control the
camera, while the other mode is time-based.
When the time-based mode is set, priority is
given to a user for a specified amount of time
and when time expires, the next person who
takes control is given priority for that same
amount of time.
Network Security Features
IP Filtering
User access to the SNC-RZ30 can be limited by IP
filtering. Up to ten different groups can be
established by defining an IP address range for
each group. This allows users with IP addresses
in a defined range to access the camera, while
denying access to all other addresses.
Page 7
SUPPLIED ACCESSORIES
Ceiling Mount Kit
OPTIONAL ACCESSORIES
MSH-32/64/128
Memory Stick
(32 MB/64 MB/128MB)
MSAC-PC3
Memory Stick/PC Card Adaptor
AC Power Adaptor
CD-ROM (setup program and user's guide)
I/O Receptacle
Installation Manual
Ferrite Core
SAMPLE SYSTEM CONFIGURATION
Page 8
© 2004 Sony Corporation. All rights reserved.
Reproduction in whole or in part without written permission is prohibited.
Features and specifications are subject to change without notice.
All non-metric weights and measurements are approximate.
Some images in this catalog are simulated.
Sony is a registered trademark of Sony Corporation.
Memory Stick is a trademark of Sony Corporation.
All other trademarks are the property of their respective owners.
MSD2004-346(10166V1)WEL00018
Distributed by
SPECIFICATIONS
SNC-RZ30N/2 SNC-RZ30P/2
Camera
Image device
1
/6 type Interline Transfer Super HAD CCD
Number of total pixels 680,000 pixels 800,000 pixels
Electronic shutter
1
/4 to 1/10,000 sec.
1
/3 to 1/10,000 sec.
Gain control Auto/Manual (-3 dB to 28 dB)
Exposure control Auto (Full auto, Shutter-priority, Iris-priority),
Manual, EV compensation, Back light compensation
White balance mode Auto, Indoor, Outdoor, One-push auto, Manual
Lens type Auto-focus zoom lens
Zoom ratio 25x optical zoom (300x with digital zoom)
Horizontal view angle 2.0 degrees to 45 degrees
Focal length f = 2.4 mm to 60 mm
F-number F1.6 (wide), F2.7 (tele)
Minimum object distance 300 mm (wide), 800 mm (tele)
Pan angle -170 degrees to +170 degrees
Pan speed 2 sec./340 degrees
Tilt angle -90 degrees to +25 degrees
Tilt speed 1.5 sec./115 degrees
Other functions Day/Night, Activity detection, Image stabilizer,
Position preset
Image
Image size 736 x 480, 640 x 480, 736 x 544, 640 x 480,
320 x 240, 160 x 120 320 x 240, 160 x 120
Compression format JPEG
Compression ratio approx.1/5 to 1/60 (10 steps)
Maximum frame rate 30 fps (640 x 480) 25 fps (640 x 480)
SNC-RZ30N/2 SNC-RZ30P/2
Network
Protocols TCP/IP, HTTP, ARP, ICMP, FTP, SMTP, DHCP,
SNMP (MIB2)
Number of clients 50
Interface
Ethernet 10Base-T/100Base-TX (RJ-45)
Serial interface RS-485/232C
(Transparency function or VISCA protocol)
I/O port Sensor in x 3, Alarm out x 2
Card slot PC Card Type II x 2
Analog video output BNC x1, 1.0 Vp-p, 75Ω
Analog Video Output
Signal system NTSC (Composite) PAL (Composite)
Horizontal resolution 480 TV lines
S/N ratio 48 dB
Minimum illumination Color: 2.5 lx.
(50IRE, F1.6: AE mode, slow shutter off)
General
Mass 1.2 kg (2 lb 10 oz)
Dimensions (W x H x D) 140 x 175 x 144 mm (5 5/8 x 7 x 53/4 inches)
Power requirements 12 V DC via supplied AC adaptor (AC 100 to 240 V)
Power consumption 21.6 W max.
Operating temperature 0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature -20 °C to + 60 °C (-4 °F to 140 °F)
Operating humidity 20% to 80% Non-condensing
Storage humidity 20% to 95% Non-condensing
Printed in Hong Kong
Loading...