To prevent fire or shock
hazard, do not expose
the unit to rain or moist
ure.
For the customers in the
U.S.A.
This symbol is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the
appliance.
Owner’s Record
The model number and serial numbers
are located at the rear. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you
call upon your Sony dealer regarding
this product.
Model No. SA-W10
Serial No.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority
to operate this equipment.
CAUTION
Use of this appliance with some systems
may present a shock or fire hazard. Do
not use with any units which have the
following marking located near output.
WARNING: HAZARDOUS ENERGY!
Note to CATV system installer:
This reminder is provided to call CATV
system installer’s attention to Article
820-40 of the NEC that provides
guidelines for proper grounding and, in
particular, specifies that the cable
ground shall be connected to the
grounding system of the building, as
close to the point of cable entry as
practical.
For detailed safety precautions, see the
leaflet “IMPORTANT SAFEGUARDS”
included with this manual in the vinly
bag.
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, DO
NOT USE THIS POLARIZED AC PLUG
WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLAD
EXPOSURE.
NOTICE FOR THE CUSTOMERS
IN THE UNITED KINGDOM
A moulded plug complying with BS
1363 is fitted to this equipment for your
safety and convenience.
Should the fuse in the plug supplied
need to be replaced a 5 AMP fuse
approved by ASTA or BSI to BS 1362,
(i.e. marked with 2 or @ mark) must be
used.
If the plug supplied with this equipment
has a detachable fuse cover, be sure to
attach the fuse cover after you change
the fuse. Never use the plug without the
fuse cover. If you should lose the fuse
cover, please contact your nearest Sony
service station.
IMPORTANT
If the plug supplied is not suitable for
the socket outlets in your home, it
should be cut off and an appropriate
plug fitted in accordance with the
following instructions.
The wires in this mains lead are
coloured in accordance with the
following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the
mains lead of this apparatus may
not correspond with the coloured
markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured blue
must be connected to the terminal
which is marked with the letter N or
coloured black. The wire which is
coloured brown must be connected
to the terminal which is marked
with the letter L or coloured red. Do
not connect either wire to the earth
terminal in the plug which is
marked by the letter E or by the
safety earth symbol Y or coloured
green or green-and-yellow.
WARNING
To prevent shock hazard, do no insert
the plug cut off from the mains lead into
a socket outlet. This plug cannot be used
and should be destroyed.
EN
2
1/02-03_SAW10.EN 3-810-424-12 (1)
Welcome!
Thank you for purchasing the Sony
Active Super Woofer. Before operating
this woofer, please read this manual
thoroughly and retain it for future
reference.
TABLE OF CONTENTS
Getting Started
Unpacking 4
Installation 4
Hooking Up the System 5
Install the woofer wherever you like because with the
bass sound range reproduced from the woofer (below
150 Hz), human hearing cannot detect the direction
and position in which the sound is being produced.
Also, since the feeling of stereo is lost with bass
frequencies, a single woofer is enough for reproducing
the bass of stereo channels.
To obtain a better bass reproduction, we recommend
that you install the woofer on a solid floor where
resonance is unlikely to occur.
Notes
• Always install the woofer vertically, keeping a few
centimeters from away the wall.
• Do not place an object on the woofer or sit on it.
• If the woofer is installed in the center of a room, the bass
could be extreamely weakened. This is due to the
influence of the standing wave of the room. If this
happened, move the woofer away from the center of a
room or eliminate the cause of the standing wave, by
installing a bookshelf on the wall, etc.
EN
4
1/04–05_WSA10.11EN 3-810-424-12 (1)
Hooking Up the System
Overview
Use either the INPUT 1 jack or the INPUT 2 terminals
of the woofer when you connect the amplifier.
• If your amplifier has one of the following types of
output jacks, connect the INPUT 1 jack and the
amplifier's jack using the supplied audio connecting
cord.
— MONO OUT jack
— MIX OUT jack
— SUB WOOFER output jack(s)
— SUPER WOOFER output jack(s)
• If your amplifier does not have the above mentioned
output jacks, connect the speaker terminals of the
amplifier to the INPUT 2 terminals instead.
Getting Started
Note
Use either INPUT 1 or INPUT 2 for the connection. Using
both may result in a malfunction.
SPEAKERINPUT1
SPEAKER
L
+–R+–
INPUT 1
+–R+–
L
INPUT 2
INPUT2
Before you get started
• Turn off the power of the amplifier and the woofer
before making any connection.
• Use the audio connecting cords that are supplied to
the respective equipment. If there are not enough
audio connecting cords to make the necessary
connections, you need to purchase some optional
audio connecting cords.
• Be sure to make connections firmly to avoid noise.
• Connect the AC power cord from the woofer to a
wall outlet.
• You cannot connect the CENTER output jack for use
with Dolby Pro Logic function to the woofer. Bass
sound is not output with some Dolby Pro Logic
modes.
(continued)
1/04–05_WSA10.11EN 3-810-424-12 (1)
EN
5
Getting Started
INPUT 2
+–
R+–L
SPEAKER B
R+–L+–
Connecting to an amplifier with a single set
of speaker terminals
If your amplifier is equipped with a single set of
speaker terminals, connect the woofer to the amplifier,
and then connect the front speakers to the woofer.
What cords will I need?
Speaker cord (supplied) (1 for each speaker)
Twist the stripped ends of the cord about 2/3 inch (15 mm).
Be sure to match the speaker cord to the appropriate
terminal on the componentes: + to + and – to –. If the cords
are reversed, the sound will be distorted and will lack bass.
It is useful to decide that the speaker cord marked with a
line is always the positive (+) and should be connected to the
positive (+) terminal to avoid any improper connections.
Hookups
1 Connect the woofer to the amplifier.
Connect the INPUT 2 terminals of the woofer to
the amplifier’s speaker terminals with the speaker
cords. Be sure to connect both L and R channels.
ç: signal flow
Amplifier
SPEAKER
R+–L+–
Connecting to an amplifier with
double(A+B) sets of speaker terminals
If your amplifier has double(A+B) sets of speaker
terminals, connect both the woofer and the front
speakers to the amplifier.
What cords will I need?
Speaker cord (supplied) (1 for each speaker)
Twist the stripped ends of the cord about 2/3 inch (15 mm).
Hookups
1 Connect the front speakers to the amplifier.
Connect the speakers to your amplifier’s speaker
terminals (A).
Amplifier
SPEAKER A
R+–L+–
Front
Speaker (R)
}]
Front
Speaker (L)
}]
2 Connect the front speakers to the woofer.
Connect the speakers to the speaker terminals of
the woofer.
Front
Speaker (R)
EN
6
}]
This woofer
+–
R+–L
INPUT 2
This woofer
SPEAKER
+–R+–
L
Front
Speaker (L)
}]
2 Connect the woofer to the amplifier.
Connect the INPUT 2 terminals of the woofer to
the amplifier’s speaker terminals (B) using
speaker cords (supplied).
Amplifier
This woofer
When using the double (A +B) sets of speakers, make
sure that you select the “A +B” position with your
amplifier.
Note
When you are using speaker terminal (A) only (front speaker
only) or when the power of the amplifier is turned off, turn
down the volume or turn off the power of the woofer
otherwise, hum noise may be heard.
1/06-07_WSA10.11EN 3-810-424-12 (1)
Getting Started
Connecting to an amplifier with a special
jack for a super woofer
If your amplifier has a special jack for a super woofer
(like a MONO OUT jack, MIX OUT jack, SUB
WOOFER jack or SUPER WOOFER jack), connect the
INPUT 1 jack of the woofer to one of those jacks.
What cords will I need?
Audio connecting cord (supplied) (1)
Hookups
Connect the INPUT 1 jack of the woofer to one of
special jack of the amplifier with the supplied audio
connecting cord.
AmplifierThis woofer
MONO OUT
INPUT 1
Note
If the output level of your amplifier is not large enough, the
sound may not be loud enough. In this case, connect the
speaker terminals of the amplifier directly to the INPUT2
terminals of the woofer.
Setting the VOLTAGE SELECTOR
(Not provided on European, North
American and Malaysian models)
Check that the VOLTAGE SELECTOR on the rear
panel of the deck is set to the local power line voltage.
If not, set the selector to the correct position using a
screwdriver before connecting the AC power cord to a
wall outlet.
220 - 240 V110 - 120 V
Connecting the AC power cord
Connect the AC power cord from the woofer and from
your amplifier to a wall outlet.
1/06-07_WSA10.11EN 3-810-424-12 (1)
EN
7
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.