Sony S2 Sports Walkman SRF-M85W User Manual

2-585-437-31(1)
WEATHER/FM Stereo/AM PLL Synthesized Radio
Operating Instructions
“WALKMAN” is a registered trademark of Sony Corporation to represent Headphone Stereo products. is a registered trademark of Sony Corporation.
WEATHER/FM/AM WALKMAN
SRF-M85W
©2008 Sony Corporation Printed in China
For customers who purchased this product in the USA Please register this product on line at http://www.sony.com/productregistration. Proper registration will enable us to send you periodic mailings about new products, services, and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you.
WARNING
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
This device complies with the Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
If you have any questions about this product, you may call; Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/
Trade Name: SONY Model: SRF-M85W Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 USA Telephone Number: 858-942-2230
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Features
• WEATHER/FM/AM 3 band PLL (phase locked loop) synthesized armband radio.
•A total of 25 stations can be preset, 5 WEATHER stations, 15 FM stations and 5 AM stations.
• Stopwatch, split and pitch timer functions.
• Wearable round design for armband and belt-holder use.
• Water-resistant for all –weather use.
• MEGA BASS for dynamic bass sound.
Precautions
• Operate the unit only on 1.5 V DC with one size AAA (R03) battery.
• Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or mechanical shock. Never leave the unit in a car parked under the sun.
• Should anything fall into the unit, remove the battery and have the unit checked by qualified personnel before operating it any further.
• To clean the casing, use a soft cloth dampened with a mild detergent solution.
• In vehicles or buildings, radio reception may be difficult or noisy. Try listening near a window.
Notes on Headphones
Road safety
Do not use headphones while driving, cycling, or operating any motorized vehicle. It may create a traffic hazard and is illegal in many areas. It can also be potentially dangerous to play your headphones at high volume while walking, especially at pedestrian crossings. You should exercise extreme caution or discontinue use in potentially hazardous situations.
Preventing hearing damage
Avoid using headphones at high volume. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, reduce volume or discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you to hear outside sounds and to be considerate to people around you.
Declaration of Conformity
Warning
If there is lightning when you are using the unit, take off the headphones immediately.
Cautions on Water-resistance
This unit is designed so that it can be used with slight exposure to rain, snow and other forms of moisture, but there are several points on which caution should be observed.
• Do not allow it to come in contact with large amounts of water.
• Do not immerse it in water.
• If water should get on it or if it should fall into water, take it out immediately
and wipe it off with a dry cloth. The interior of the battery compartment has no water-resistance. The battery may corrode, so wipe out the interior of the battery compartment as follows. – Open or close the battery compartment with dry hands in a place without
exposure to any water.
– Wipe off the battery and the inside of the battery compartment. Give special
attention to the contacts so that no water remains on them.
If you have any questions or problems concerning your unit, please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made the following checks, consult your nearest Sony dealer.
All buttons do not operate at all.
•“-” is displayed. Slide down the HOLD lever so that “-” disappears.
Very weak or interrupted sound, or unsatisfactory reception
• Weak battery
• In a vehicle or in a building, move closer to a window.
There is hum or noise.
• If WB/FM SENS is set to LOCAL, set to DX.
Noise occurs.
• Ensure that the unit is not near a mobile phone or any other device that emits radio waves.
Display is dim, or no indication is displayed.
• Weak battery.
• The unit is being used in extremely high or low temperatures or in a place with excessive moisture.
The station cannot be received when the preset was tuned.
• You chose the wrong preset number.
• The memory of the station has been initialized. Preset the station again.
The power cannot be turned on, and “ display.
• The battery has been completely exhausted.
The preset stations may be initialized, if a maintenance service is performed. Please note down your settings in case you want to preset them again.
” is flashing in the
Specifications
Time display
12-hour system
Frequency range
Band Range Channel step
WEATHER 1 - 7 ch 1 channel
FM 87.5 – 108 MHz 0.1 MHz
AM 530 – 1 710 kHz 10 kHz
Output
ii
i (headphones) jack (ø 3.5 mm stereo mini jack) 16
ii
Power output
5 mW + 5 mW (at 10 % harmonic distortion)
Power requirements
1.5 V DC, one size AAA (R03) battery
Dimensions
Approx. 95.5 × 69.3 × 37.5 mm (w/h/d)
7
/8 × 2 3/
(3
Mass
Approx. 88.3 g (3.1 oz.) incl. battery
Supplied accessories
Design and specifications are subject to change without notice.
× 1 1/2 inches) incl. projecting parts and controls
4
Stereo headphones (vertical in the ear type) (1), Arm band (1)
Installing the Battery
(See Fig. A– )
Open the battery compartment lid and install one size AAA (R03)
1
battery (not supplied) with correct polarity.
When a battery is first installed, “AM 12:00” flashes in the display. Once the current time is set, the flashing stops.
2 Close the lid.
When using WEATHER FM AM
Sony alkaline 27 27 36 size AAA (LR03)
Sony size AAA (R03) 10 10 16
* Measured by JEITA (Japan Electronics and Information Technology Industries
Association) standards. The actual battery life may vary depending on the circumstance of the unit.
When to replace the battery
You can check the remaining battery power that appears in the display. The indicators are as follows:
Indicator
Full strength*
x
Weakening*
x
When the battery becomes exhausted, the unit will turn off. Replace with new battery. When you press POWER after installing the new battery, the indicator changes to “
* Displayed only when the radio is turned on.
Note
Do not take more than 30 seconds to replace the battery, otherwise, your clock, pitch timer and countdown timer settings and preset stations will be initialized. Should that happen, reset the functions again.
”.
Notes on battery
• Do not charge the dry battery.
• Do not carry the dry battery together with coins or other metallic objects. It can generate heat if the positive and negative terminals of the battery are accidentally come into contact with metallic objects.
• When you are not going to use the unit for a long time, remove the battery to avoid damage from battery leakage and corrosion.
To attach the battery compartment lid if it is accidentally detached (See Fig. A– )
The battery compartment lid is designed to come off when opened with excessive force. To put it back on, see the illustration.
1 Insert one side of the lid as illustrated. 2 Push the other side to attach.
A
Insert the E side of the battery first.
Size AAA (R03) × 1
i (headphones) jack
POWER
START/STOP
SPLIT/RESET
MEGA BASS
VOL*
1
2
Connector
Rubber belt
Rubber belt
TUNE/TIME SET +/–*
*1The TUNE/TIME SET
+ has a tactile dot.
WB/FM SENS DX/LOCAL
*2There is a tactile dot beside VOL to show the direction to turn up
the volume.
B
HOLD lever
ENTER MODE
BAND
DISPLAY
Belt clip
Wraparound arm band
C
D
Using the Arm Band
(See Fig. B– )
Slide the connector onto the unit until you hear a click.
1 2 Unwind and straighten the wraparound arm band.
To more easily straighten the band, slightly bend the tip of the band in the opposite direction.
3 Hold the body of the unit and attach the straightened band to your
arm.
The band will wind by itself.
4 Tighten the band with the rubber belt.
To remove the arm band from the unit (See Fig. B– )
While holding down “PUSH RELEASE” (1), slide the connector to remove the arm band (2).
The arm band can be attached either on left or right arm by changing up side down. The unit can also be removed with the arm band attached on your arm, as instructed above.
To vary the length of the rubber belt to fit your arm (See Fig. B–
Move the velcro fastener to the proper position.
If the rubber belt and wraparound band becomes dirty
Remove the rubber belt from the unit and clean them.
Caution (See Fig. B–
• Avoid bending the wraparound band forcibly in the opposite direction. It may break.
• The straightened band will wind easily when you touch or wiggle it. Be sure to treat it carefully.
)
Preventing Accidental Change
— HOLD Function
When you slide HOLD in the direction of the arrow, “-” appears in the display. All the other buttons on the radio will become inoperative. This function prevents the radio from being unintentionally turned on, or the radio frequency from being accidentally changed.
To cancel HOLD, slide HOLD in the opposite direction of the arrow so that “ -” disappears.
Setting the Clock
The display will flash “AM 12:00” when the battery is first inserted.
1 Press DISPLAY repeatedly to select the clock mode when the
clock mode is not on.
2 Hold down ENTER for more than 2 seconds.
The beep sounds and the hour flashes in the display.
3 Press TUNE/TIME SET + or – until the correct hour appears in
the display.
Each press changes the digit(s) by one. When you keep the button pressed, the digit(s) change rapidly.
4 Press ENTER.
The beep sounds and the minute starts to flash. Repeat step 3 to set the minute. After setting the minute, press ENTER again. The two beeps sound and the clock starts from 0 seconds.
Notes
• One you start setting the clock, you must perform each step within 65 seconds, or the clock setting mode will be cancelled.
• 12-hour system: “AM 12:00” = midnight, “PM 12:00” = noon.
Changing AM Channel Step
The AM channel step differs depending on areas. The channel step of this unit is factory-set to 10 kHz. Change the settings as shown below to be able to listen to the radio.
Area Channel step
North and South American countries/regions 10 kHz
Other countries/regions 9 kHz
Note
When the AM channel step is changed, the preset stations for AM will be initialized.
1 Press POWER to turn off the power. 2 Press DISPLAY repeatedly to select the clock mode when the
clock mode is not on.
3 While holding down TUNE/TIME SET + or –, keep pressing
MODE for more than 5 seconds.
Two short beeps sound, and the AM channel step will be changed. “AM 9” (or “AM 10”) is displayed for about 2 seconds. If you proceed to step 3 again, the channel step changes again.
3 Press TUNE/TIME SET + or – to select the number you wish to
Selecting the Mode
You can use this unit as a radio, clock, stopwatch, pitch timer or countdown timer. The functions of clock, stopwatch, pitch timer, countdown timer are available even if the power is off.
Press DISPLAY to select a function mode. Each function mode can be selected as follows:
Radio frequency* Clock
Countdown timer
* Selected only when the power is on.
)
Playing the Radio
Stopwatch
Pitch timer
— Manual Tuning 1 Connect the headphones to the i (headphones) jack. 2 Press POWER to turn on the radio.
RADIO ON” appears in the display.
3 If “P” is displayed, press MODE so that “P” disappears.
Pressing MODE will switch over between manual tuning mode and preset tuning mode.
4 Press BAND to select the band.
Each press changes the band as follows:
5 Press TUNE/TIME SET + or – to select the desired frequency.
If you hold down TUNE/TIME SET + or –, the frequency or channel changes rapidly. When the frequency matches the broadcast frequency, the broadcast will be received.
6 Adjust the volume using VOL.
To turn off the radio, press POWER.
Improving the Reception
WEATHER/FM: Extend the headphones cord which
Set WB/FM SENS to LOCAL if interference is prevalent and reception is too strong. Under normal conditions, set it to DX.
Note
If WB/FM SENS is set to LOCAL under normal conditions, reception sensitivity will decrease.
functions as the WEATHER/FM antenna (See Fig. C-
AM: Rotate the unit horizontally for optimum
reception. A ferrite bar antenna is built­in the unit (See Fig.C-
).
).
Obtain Powerful Bass Sound
Press MEGA BASS.
MB” indication appears in the display when the MEGA BASS function is on. The MEGA BASS function intensifies the bass sound for richer quality audio reproduction.
Presetting Your Favorite Station
— Preset Tuning
You can preset up to 5 stations each for WEATHER and AM, and 15 stations for FM. Also, you can delete the preset station whether it is factory-set or preset by yourself.
Presetting a Station
1 Follow steps 1 to 5 in “Playing the Radio” and manually tune in to
the station you wish to preset.
2 Hold down ENTER until the preset number flashes.
If there is a preset number that has no preset station, that preset number flashes. When all the preset numbers are set to certain stations, the following occurs:
• Initialized (factory-set): “1” flashes and “P” appears.
• After tuning in a preset station: The next preset number after the one last
preset flashes and “P” appears.
preset, then press ENTER.
When you select the preset number using TUNE/TIME SET + or –, “P” appears if that number has a preset station. If it has no preset station, only the number flashes and “P” does not appear. When you press ENTER, the selected preset number lights up in the display.
Example: Display window when you preset FM 90.0 MHz in preset
To preset another station, repeat these steps. To change the preset station, preset a new station. The previous station will be canceled.
To cancel the presetting mode, press MODE.
Note
If you do not press TUNE/TIME SET + or –, or ENTER within 65 seconds, the preset tuning mode will be canceled.
number 2.
Tuning in to a Preset Station
1 Press POWER to turn on the radio. 2 Press MODE so that “P” and preset number appear. 3 Select the band with BAND. 4 Press TUNE/TIME SET + or – to select the desired preset
number.
5 Adjust the volume using VOL.
To turn off the radio, press POWER.
Note
If you hold down MODE for more than 2 seconds, the unit enters the preset station deleting mode. Press MODE again to return to the previous mode.
Deleting a Preset Station
1 Follow steps 1 and 2 in “Tuning in to a Preset Station”. 2 Select the band with BAND. 3 Press TUNE/TIME SET + or – to select the preset number to be
deleted.
4 Hold down MODE for more than 2 seconds until “P”, “ ” and
the preset number flash.
preset number to be deleted
5 While the letters and the preset number are flashing, press
ENTER.
The station set to the preset number just before the deleted station will be displayed. To delete other stations, repeat steps 2 to 5. If all the preset stations are deleted, “P -” appears in the display.
To cancel deleting, press MODE while “P”, “ are flashing.
” and the preset number
Using the Stopwatch
The stopwatch can time up to 99 hours 59 minutes and 59.99 seconds, in 1/100­second increments.
1 Press DISPLAY to select the stopwatch.
STPW” flashes in the display.
2 Press START/STOP to start.
The display shows the elapsed time.
3 Press START/STOP to stop.
To reset to zero, press SPLIT/RESET when the stopwatch is in the stop status.
The stopwatch comes with two display modes. To switch to the hour-minute­second display, press ENTER. To switch to the minute-second-split second display, press ENTER again.
When the count time exceeds “59:59 99” during the minute-second-split second display, the display switches to the hour-minute-second display.
To switch to the other modes during counting, press DISPLAY.
STPW” stops flashing if changed to other mode while the stopwatch counts down.
To listen to the radio while the stopwatch is running, press POWER. The display will switch to the radio frequency for a few seconds.
Displaying the Split Time
To display the current split time, press SPLIT/RESET while the stopwatch is running. “SPLIT” flashes in the display. The stopwatch keeps counting during the display.
To return to the count display, press SPLIT/RESET again while the split time is being displayed.
Using the Pitch Timer
The pitch timer allows setting the timer with an identical length of time repeatedly. The functions of the radio, the stopwatch, and the countdown timer are available even while the pitch timer is being used.
1 Press DISPLAY to select the pitch timer.
PITCH” flashes in the display.
2 Hold down ENTER for more than 2 seconds.
The beep sounds and the countdown duration flashes in the display.
3 Press TUNE/TIME SET + or – to set the desired countdown
duration for the pitch timer.
The countdown duration can be set from 1 second to 59 minutes 59 seconds, in 1-second increments.
4 Press ENTER.
The beep sounds and the number of times flashes in the display.
5 Press TUNE/TIME SET + or – to set the desired number of
times.
The number of times can be set up to 99.
6 Press ENTER.
The two beeps sound and the number of times stops flashing.
7 Press START/STOP.
Countdown starts. After the preset countdown duration, the two beeps sound three times.
When the last pitch timer setting is finished, the display switches to the pitch timer display even in another display mode and a long beep sounds, and then returns to the previous display. To stop the long beep, press any button.
To pause the countdown on the pitch timer, press START/STOP while counting down. At this time, the countdown is reset by pressing SPLIT/RESET. The display will show the set-up countdown duration and number of times.
To switch to the other modes, press DISPLAY.PITCH” stops flashing if changed to other mode while the pitch timer counts down.
Using the Countdown Timer
You can use the built-in countdown timer to turn off the radio automatically after a preset duration.
1 Press DISPLAY to select the countdown timer.
TIMER” flashes in the display.
2 Hold down ENTER for more than 2 seconds.
The beep sounds, and the countdown duration starts flashing.
3 Press TUNE/TIME SET + or – to set the desired countdown
duration for the timer.
The countdown duration can be set from 1 minute to 2 hours, in 1-minute increments.
4 Press ENTER.
The two beeps sound and the countdown duration stops flashing.
5 Press START/STOP.
Countdown starts. The radio is automatically turned on when the radio is off. After the preset countdown duration, the four beeps sound five times and the radio is turned off. To stop the beeps, press any button.
To turn off the radio before the preset time, press POWER.
To pause the countdown on the countdown timer, press START/STOP while counting down. At this time, the countdown is reset by pressing SPLIT/RESET. The display will show the set-up countdown duration.
To switch to the other modes, press DISPLAY.TIMER” stops flashing if changed to other mode while the countdown timer counts down.
Using the Belt Clip
(See Fig. D)
Use the belt clip when attaching the unit to your belt.
Loading...