To reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
To avoid electrical shock, do not
open the cabinet. Refer servic ing to
qualified personnel only.
The mains lead must be changed
only at a qualified service shop.
Batteries or batteries installed
apparatus shall not be exposed to
excessive heat such as sunshine,
fire or the like.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
of the unit.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this DVD recorder is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
Notice for customers in the
United Kingdom and
Republic of Ireland
A molded plug complying with
BS1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug
supplied need to be replaced, a 5
AMP fuse approved by ASTA or
BSI to BS1362, (i.e., marked with
or mark) must be used.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
Precautions
• This unit operates on 220 –
240 V AC, 50/60 Hz. Check that
the unit’s operating voltage is
identical with your local power
supply.
• To prevent fire or shock hazard,
do not place objects filled with
liquids, such as vases, on the
apparatus.
• Install this system so that the
mains lead can be unplugged
from the wall socket
immediately in the event of
trouble.
GUIDE Plus+ and G-LINK are (1)
registered trademarks or
trademarks of, (2) manufactured
under license from and (3) subject
of various international patents and
patent applications owned by, or
licensed to, Gemstar-TV Guide
International, Inc. and/or its related
affiliates.
GEMSTAR-TV GUIDE
INTERNATIONAL, INC. AND/
OR ITS RELATED AFFILIATES
ARE NOT IN ANY WAY
LIABLE FOR THE ACCURACY
OF THE PROGRAM
SCHEDULE INFORMATION
PROVIDED BY THE GUIDE
PLUS+ SYSTEM. IN NO EVENT
SHALL GEMSTAR-TV GUIDE
INTERNATIONAL, INC. AND /
OR ITS RELATED AFFILIATES
BE LIABLE FOR ANY
AMOUNTS REPRESENTING
LOSS OF PROFITS, LOSS OF
BUSINESS, OR INDIRECT,
SPECIAL, OR
CONSEQUENTIAL DAMAGES
IN CONNECTION WITH THE
PROVISION OR USE OF ANY
INFORMATION, EQUIPMENT,
OR SERVICES RELATING TO
THE GUIDE PLUS+ SYSTEM.
This label is located on the laser
protective housing inside the
enclosure.
2
Disposal of Old Electrical
& Electronic Equipment
(Applicable in the
European Union and
other European countries
with separate collection
systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic
equipment. By ensuring this
product is disposed of correctly,
you will help prevent potential
negative consequences for the
environment and human health,
which could otherwise be caused
by inappropriate waste handling of
this product. The recycling of
materials will help to conserve
natural resources. For more
detailed information about
recycling of this product, please
contact your local Civic Office,
your household waste disposal
service or the shop where you
purchased the product.
Disposal of waste
batteries (applicable in
the European Union and
other European countries
with separate collection
systems)
This symbol on the battery or on
the packaging indicates that the
battery provided with this product
shall not be treated as household
waste.
By ensuring these batteries are
disposed of correctly, you will help
prevent potentially negative
consequences for the environment
and human health which could
otherwise be caused by
inappropriate waste handling of the
battery. The recycling of the
materials will help to conserve
natural resources.
In case of products that for safety,
performance or data integrity
reasons require a permanent
connection with an incorporated
battery, this battery should be
replaced by qualified service staff
only.
To ensure that the battery will be
treated properly, hand over the
product at end-of-life to the
applicable collection point for the
recycling of electrical and
electronic equipment.
For all other batteries, please view
the section on how to remove the
battery from the product safely.
Hand the battery over to the
applicable collection point for the
recycling of waste batteries.
For more detailed information
about recycling of this product or
battery, please contact your local
Civic Office, your household
waste disposal service or the shop
where you purchased the product.
The manufacturer of this
product is Sony Corporation,
1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. The
Authorized Representative
for EMC and product safety
is Sony Deutschland GmbH,
Hedelfinger Strasse 61,
70327 Stuttgart, Germany.
For any service or guarantee
matters please refer to the
addresses given in separate
service or guarantee
documents.
Precautions
This equipment has been tested
and found to comply with the
limits set out in the EMC
Directive using a connection
cable shorter than 3 metres.
On safety
Should any solid object or liquid
fall into the cabinet, unplug the
recorder and have it checked by
qualified personnel before
operating it any further.
About the hard disk drive
The hard disk has a high storage
density, which enables long
recording durations and quick
access to the written data.
However, it can easily be
damaged by shock, vibration or
dust, and should be kept away
from magnets. To avoid losing
important data, observe the
following precautions.
• Do not apply a strong shock to
the recorder.
• Do not place the recorder in a
location subject to mechanical
vibrations or in an unstable
location.
• Do not place the recorder on
top of a hot surface, such as a
VCR or amplifier (receiver).
• Do not use the recorder in a
place subject to extreme
changes in temperature
(temperature gradient less than
10 °C/hour).
• Do not move the recorder with
its mains lead connected.
• Do not disconnect the mains
lead while the power is on.
• When disconnecting the mains
lead, turn off the power and
make sure that the hard disk
drive is not operating (the
clock is displayed in the front
panel display for at least 30
seconds and all recording or
dubbing has stopped).
• Do not move the recorder for
one minute after you have
unplugged the mains lead.
• Do not attempt to replace or
upgrade the hard disk by
yourself, as this may result in
malfunction.
If the hard disk drive should
malfunction, you cannot recover
lost data. The hard disk drive is
only a temporary storage space.
,continued
3
About repairing the hard
disk drive
• The contents of the hard disk
drive may be checked in case
of repair or inspecti on during a
malfunction or modification.
However, the con tents will not
be backed up or saved by
Sony.
• If the hard disk needs to be
formatted or replaced, it will
be done at the discretion of
Sony. All contents of the hard
disk drive will be erased,
including contents that violate
copyright laws.
On power sources
• The recorder is not
disconnected from the AC
power source (mains) as long
as it is connected to the wall
outlet, even if the recorder
itself has been turned off.
• If you are not going to use the
recorder for a long time, be
sure to disconnect the recorder
from the wall outlet. To
disconnect the AC power cord
(mains lead), grasp the plug
itself; never pull the cord.
On placement
• Place the recorder in a location
with adequate ventilation to
prevent heat build-up in the
recorder.
• Do not place the recorder on a
soft surface such as a rug that
might block the ventilation
holes.
• Do not place the recorder in a
confined space such as a
bookshelf or similar unit.
• Do not place the recorder in a
location near heat sources, or
in a place subject to direct
sunlight, excessive dust, or
mechanical shock.
• Do not place the recorder in an
inclined position. It is
designed to be operated in a
horizontal position only.
• Keep the recorder and discs
away from equipment with
strong magnets, such as
microwave ovens, or large
loudspeakers.
• Do not place heavy objects on
the recorder.
4
On recording
Make trial recordings before
making the actual recording.
On compensation for lost
recordings
Sony is not liable and will not
compensate for any lost
recordings or relevant losses,
including when recordings are
not made due to reasons
including recorder failure, or
when the contents of a recording
are lost or damaged as a result of
recorder failure or repair
undertaken to the recorder. Sony
will not restore, recover, or
replicate the recorded contents
under any circumstances.
Copyrights
• Television programmes, films,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of
such material may be contrary
to the provisions of the
copyright laws. Also, use of
this recorder with cable
television transmission may
require authorization from the
cable television transmitter
and/or programme owner.
• This product incorporates
copyright protection
technology that is protect ed by
U.S. patents and other
intellectual property rights.
Use of this copyright
protection technology must be
authorized by Macrovision,
and is intended for home and
other limited viewing uses
only unless otherwise
authorized by Macrovision.
Reverse engineering or
disassembly is prohibited.
• This Product includes
FontAvenue
by NEC corporation.
FontAvenue is a registered
trademark of NEC
corporation.
®
fonts licenced
Copy guard function
Since the recorder has a copy
guard function, programmes
received through an external
tuner (not supplied) may contain
copy protection signals (copy
guard function) and as such may
not be recordable, depending on
the type of signal.
IMPORTANT NOTICE
Caution: This recorder is
capable of holding a still
video image or on-screen
display image on your
television screen
indefinitely. If you leave the
still video image or onscreen display image
displayed on your TV for an
extended period of time you
risk permanent damage to
your television screen.
Plasma display panels and
projection televisions are
especially susceptible to this.
If you have any questions or
problems concerning your
recorder, please consult your
nearest Sony dealer.
About this manual
• In this manual, the internal
hard disk drive is written as
“HDD,” and “disc” is used as a
general reference for the HDD,
DVDs, or CDs unless
otherwise specified by the text
or illustrations.
• Icons, such as , listed
at the top of each explanation
indicate what kind of media
can be used with the function
being explained.
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar
names as those on the remote.
• The on-screen display
illustrations used in this
manual may not match the
graphics displayed on your TV
screen.
• The explanations regarding
DVDs in this manual refer to
DVDs created on this recorder.
The explanations do not apply
to DVDs that are created on
other recorders and played
back on this recorder.
Automatically
formatted in +VR
mode (DVD+RW
VIDEO)
Format in VR mode
(page 31)
Format in Video
mode
(page 31)
Compatibility with other
DVD players (finalising)
Dub HDD contents to a
DVD (VR mode) to play
on other DVD players
Dub HDD contents to a
DVD (Video mode) to play
on other DVD players
Playable on DVD+RW
compatible players
(automatically finalised)
Playable o nly on VR mode
compatible players
(finalisation unnecessary)
Playable on most DVD
players (finalisation
necessary) (page 40)
DVD+R
DVD+R DL
DVD-R
VR
mode
DVD-R DLVideo
mode
-
-
+
RVR
R
R
Video
Automatically
formatted in +VR
mode (DVD+R
VIDEO)
Format in VR mode
(page 31)
*1
Formatting is
performed in the
“Format” setup
(page 42).
Automatically
formatted in Video
mode
Playable on most DVD
players (finalisation
necessary) (page 40)
Playable only on DVD-R
in VR mode compatible
players (finalisation
necessary) (page 40)
Playable on most DVD
players (finalisation
necessary) (page 40)
,continued
9
Usable disc versions (as of April 2007)
• 8x-speed or slower DVD+RWs
• 6x-speed or slower DVD-RWs (Ver.1.1,
Ver.1.2 with CPRM
*2
)
• 16x-speed or slower DVD+Rs
• 16x-speed or slower DVD-Rs (Ver.2.0,
Ver.2.1 with CPRM
*2
)
• 8x-speed or slower DVD+R DL (Double
Layer) discs
• 8x-speed or slower DVD-R DL (Dual
Layer) discs (Ver.3.0 with CPRM
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R
DL,” “DVD-R,” and “DVD-R DL” are trademarks.
*1
When an unformatted DVD-R is inserted into
this recorder, it is automatically formatted in
Video mode. To format a new DVD-R in VR
mode, format in the “Format” setup (page 42).
*2
CPRM (Content Protection for Recordable
Media) is a coding technology that protects
copyrights for images.
*2
)
Discs that cannot be recorded on
• DVD-RAMs
10
Playable discs
TypeDisc Logo
DVD VIDEO
VIDEO CD
CD
DATA DVD—
DATA CD—
“DVD VIDEO” and “CD” are trademarks.
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
®
is a video file compression technology,
DivX
developed by DivX, Inc.
* If the DVD-RAM has a removable cartridge,
remove the cartridge before playback.
Icon used in
this manual
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are
recorded in a format different from the
formats mentioned in the table above.
• Data part of CD-Extras
•BDs
• HD DVDs
• Discs recorded with an AVCHDcompatible DVD video camera
Characteristics
Discs such as movies that can be
purchased or rented
DVD
VCD
CD
DATA DVD
DATA CD
This recorder also recognises DVDRAMs* as DVD Video compatible
discs.
VIDEO CDs or CD-Rs/CD-RWs in
VIDEO CD/Super VIDEO CD format
Music CDs or CD-Rs/CD-RWs in
music CD format
DVD+RWs/DVD+Rs/DVD-RAMs*
containing MP3 audio tracks or DivX
video files
DVD-RWs/DVD-Rs/DVD-ROMs
containing MP3 audio tracks, JPEG
image files or DivX video files
CD-ROMs/CD-Rs/CD-RWs
containing either MP3 audio tracks,
JPEG image files or DivX video files
• DVD-ROMs/DVD+RWs/DVD-RWs/
DVD+Rs/DVD-Rs that do not contain
DVD Video, DivX video, JPEG image
files, or MP3 audio tracks.
• DVD Audio discs
• Cartridge-only type DVD-RAMs.
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
(page 12).
• DVDs that were recorded on a different
recorder and not correctly finalised.
Maximum recordable number of titles
DiscNumber of titles
HDD*999
DVD-RW/DVD-R99
DVD+RW/DVD+R49
DVD+R DL49
DVD-R DL99
* The maximum length for one title is 12 hours.
,continued
11
Note on playback operations of DVD
VIDEOs/VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by
software producers. Since this recorder plays
DVD VIDEOs/VIDEO CDs according to the
disc contents the software producers
designed, some playback features may not be
available. See the instructions supplied with
the DVD VIDEOs/VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on
the rear of the unit and will only play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
DVD VIDEOs labelled will also play
ALL
on this recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region
code.” will appear on the TV screen.
Depending on the DVD VIDEO, no region
code indication may be labelled even though
playing the DVD VIDEO is prohibited by
area restrictions.
Region code
Music discs encoded with copyright
protection technologies
This product is designed to play back discs
that conform to the Compact Disc (CD)
standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please
be aware that among those discs, there are
some that do not conform to the CD standard
and may not be playable by this product.
b Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-
Rs, DVD-RAMs, or CD-RWs/CD-Rs cannot be
played on this recorder due to the recording
quality or physical condition of the disc, or the
characteristics of the recording device and
authoring software. The disc will not play if it has
not been correctly finalised. For more
information, see the operating instructions for the
recording device.
• You cannot mix VR mode an d Video mode on the
same DVD-RW. To change the disc’s format,
reformat the disc (page 42). Note that the disc’s
contents will be erased after reformatting.
• You cannot shorten the time required for
recording even with high-speed discs.
• It is recommended that you use discs with “For
Video” printed on their packaging.
• You cannot add new recordings to DVD+Rs,
DVD-Rs, or DVD-RWs (Video mode) that
contain recordings made on other DVD
equipment.
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings
made on other DVD equipment. If you do add a
new recording, note that this recorder will rewrite
the DVD menu.
• You cannot edit recordings on DVD+RWs,
DVD-RWs (Video mode), DVD+Rs, or DVD-Rs
that are made on other DVD equipment.
• If the disc contains PC data unrecognizable by
this recorder, the data may be erased.
• You may not be able to record, edit, or dub on
some recordable discs, depending on the disc.
• Do not insert any discs that cannot be recorded or
played on this recorder. This may cause the
recorder to malfunction.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does
not conform to the Compact Disc (CD)
standard, playback on this product is not
guaranteed.
12
Hookups and Settings
Using the set top box receiver
control function
Hooking Up the Recorder
Follow steps 1 through 6 to hook up and
adjust the settings of the recorder. Do not
connect the mains lead until you reach
“Step 4: Connecting the Mains Lead” on
page 20.
b Notes
• See “Specifications” (page 136) for a list of
supplied accessories.
• Plug in cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the
components to be connected.
• You cannot connect this recorder to a TV that
does not have a SCART or video input jack.
• Be sure to disconnect the mains lead of each
component before connecting.
Step 1: Connecting the
Aerial Cable and Set Top
Box Controller
Select one of the following aerial hookups.
Do NOT set “LINE 1 In” to “Decoder” in the
“Video In/Out” setup (page 114) when
making connection A.
If you haveHookup
Set top box receiverA (page 14)
No set top box receiverB (page 15)
The set top box receiver control function can
be used with hookup A. It allows the recorder
to control a set top box receiver via the
supplied set top box controller. The recorder
controls programme positions on the set top
box receiver for timer recording. You can
also use the recorder’s remote control to
change programme positions on the set top
box receiver whenever the set top box
receiver and recorder are turned on.
To use the set top box receiver control
function, you need to connect the set top box
controller (page 14). After setting up the set
top box receiver control, check that the
recorder can correctly control the set top box
receiver (page 24).
b Notes
• If your aerial is a flat cable (300-ohm twin lead
cable), use an external aerial connector (not
supplied) to connect the aerial to the recorder.
• If you have separate cables for AERIAL
antennas, use an AERIAL UHF/VHF band mixer
(not supplied) to connect the aerial to the
recorder.
• If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected set top box receiver.
Hookups and Settings
If the set top box receiver can output RGB
signals
This recorder accepts RGB signals. If the set
top box receiver can output RGB signals,
connect the TV SCART connector on the set
top box receiver to the LINE 1/DECODER
jack, and set “LINE 1 In” to “RGB” in the
“Video In/Out” setup (page 114). See the
instructions supplied with the set top box
receiver.
,continued
13
A: Connecting a set top box receiver
With this hookup, you can record any programme position on the set top box receiver.
To watch cable programmes, you need to match the programme position on the recorder to the
aerial output programme position on the set top box receiver.
Place the set top box controller
near the remote sensor on the
set top box receiver.
Wall
Set top box
controller
(page 13)
SCART cord*
(not supplied)
to G-LINK
2
Aerial cable*
(not supplied)
to AERIAL IN
Set top box
receiver
ANT IN
TO TV
1
to AERIAL OUT
Aerial cable
(supplied)
to aerial input
: Signal flow
*1
If your set top box receiver does not have an aerial output jack, connect the aerial cable to the recorder’s
AERIAL IN jack.
*2
Connect only if your set top box receiver has a SCART connector.
TV
14
DVD recorder
B: Connecting the aerial cable only (no set top box receiver)
Use this hookup if you watch cable programme position without a set top box receiver. Also
use this hookup if you are connecting only an aerial antenna.
With this hookup, you can record any programme position by selecting the programme position
on the recorder.
Wall
to AERIAL IN
DVD recorder
to AERIAL OUT
to aerial input
TV
Hookups and Settings
Aerial cable (supplied)
: Signal flow
15
Step 2: Connecting the Video Cords/HDMI Cord
Select one of the following patterns, A through E, according to the input jack on your TV
monitor, projector, or audio component such as an AV amplifier (receiver). This will enable
you to view pictures.
B
TV, projector, or audio
component
(green)
to COMPONENT
VIDEO OUT
to LINE 2 OUT
(VIDEO)
(yellow)
(red)(blue)
Component video
cord (not supplied)
Audio/video
cord (not
supplied)
SCART cord (not supplied)
to T LINE 3 – TV
to LINE 2 OUT
(S VIDEO)
to HDMI OUT
S-video cord
(not supplied)
A
TV
DVD recorder
HDMI cord
(not supplied)
16
(green)
D
TV, projector, or audio
component
: Signal flow
(red)(blue)
C
TV, projector, or audi o
component
TV, projector, or audio
component
E
A SCART input jack
When setting “LINE 3 Out” to “S-Video” or
“RGB” in the “Video In/Out” setup
(page 114), use a SCART cord that conforms
to the selected signal.
B Video input jack
You will enjoy standard quality images.
C S VIDEO input jack
You will enjoy high quality images.
D Component video input jacks (Y, PB/CB,
R/CR)
P
You will enjoy accurate colour reproduction
and high quality images.
If your TV accepts progressive 525p/625p
format signals, use this connection and set
“Progressive” to “Compatible” in the “Easy
Setup” setup (page 23). Then set
“Component Video Out” to “Progressive” in
the “Video In/Out” setup to send progressive
video signals. For details, see “Component
Video Out” on page 114.
E HDMI input jack
Use a certified HDMI cord (not supplied) to
enjoy high quality digital picture and sound
through the HDMI OUT jack.
When connecting a Sony TV that is
compatible with the HDMI control function,
see page 18.
To see the signals from the connected set top
box receiver when the set top box receiver is
connected to the recorder using a SCART
cord only, turn the recorder on.
When connecting to the HDMI jack
Follow the steps below. Improper handling
may damage the HDMI jack and the
connector.
1 Carefully align the HDMI jack on the
rear of the recorder and the HDMI
connector by checking their shapes.
Make sure the connector is not upside
down or tilted.
2 Insert the HDMI connector straight into
the HDMI jack.
Do not bend or apply pressure to the
HDMI connector.
Hookups and Settings
b Notes
• Be sure to disconnect the HDMI cord when
moving the recorder.
• Do not apply too much pressure to the cabinet
wall, if you place the recorder on the cabinet with
the HDMI cord connected. It may damage the
HDMI jack or the HDMI cord.
• Do not twist the HDMI connector while
connecting to or disconnecting from the HDMI
jack to avoid damaging the HDMI jack and
connector.
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the picture size, see
page 121.
If you are connecting to a VCR
Connect your VCR to the LINE 1/
DECODER jack on the recorder (page 26).
b Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same
time.
• Do not make connections A and E at the same
time.
• When you connect the recorder to your TV via the
SCART jacks, the TV’s input source is set to the
recorder automatically when you start playback.
If necessary, press the TV t button on the
remote to return the input to the TV.
• If you connect the recorder to a TV with
SMARTLINK, set “LINE 3 Out” to “Video” in
the “Video In/Out” setup.
• You cannot connect the HDMI OUT jack
(connection E) to DVI jacks that are not HDCP
compliant (e.g., DVI jacks on PC displays).
• Component video and RGB signals are not output
when using the HDMI connection.
* This DVD recorder incorporates High-Definition
Multimedia Interface (HDMI™) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
Not straightConnector is upside down
trademarks of HDMI Licensing LLC.
,continued
17
About the SMARTLINK
features (for SCART
connections only)
If the connected TV (or other connected
equipment such as a set top box) complies
with SMARTLINK, NexTView Link
MEGALOGIC
CINEMALINK
*1
, EASYLINK*2,
*2
, Q-Link*3, EURO VIEW
LINK*4, or T-V LINK*5, you can enjoy the
following SMARTLINK features.
• TV Direct Rec. (page 32)
• One-Touch Play (page 61)
• Preset Download
You can download the tuner preset data
from your TV to this recorder, and tune the
recorder according to that data in “Easy
Setup.”
• NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
To prepare for the SMARTLINK features
Set “LINE 3 Out” to “Video” in the “Video
In/Out” setup (page 114) and
“SMARTLINK” to “This Recorder Only” in
the “Options” setup (page 126).
b Notes
• For correct SMARTLINK connection, you will
need a SCART cord that has the full 21 pins.
Refer to your TV’s instruction manual as well for
this connection.
• Not all TVs respond to the functions above.
*1
“MEGALOGIC” is a registered trademark of
Grundig Corporation.
*2
“EASYLINK” and “CINEMALINK” are
trademarks of Philips Corporation.
*3
“Q-Link” and “NexTView Link” are trademarks
of Panasonic Corporation.
*4
“EURO VIEW LINK” is a trademark of Toshiba
Corporation.
*5
“T-V LINK” is a trademark of JVC Corporation.
*3
,
About the HDMI Control
functions for ‘BRAVIA’ Theatre
Sync (for HDMI connections
only)
By connecting Sony components that are
compatible with the HDMI Control function
with an HDMI cord (not supplied), operation
is simplified as below:
• One-Touch Play (page 61)
• System Power-Off
When you turn the TV off by using the
power button on the TV’s remote, the
components compatible with the HDMI
Control function turn off automatically.
To prepare for the ‘BRAVIA’ Theatre Sync
features
Set “HDMI Control” to “On” in the “HDMI
Output” setup (page 125). For details on TV
settings, refer to the operating instructions
supplied with the TV.
b Notes
• Depending on the connected component, the
HDMI Control function may not work. Refer to
the operating instructions supplied with the
component.
• The recorder supports only the playback option of
HDMI Control. “Player” appears on the TV
screen when using the HDMI Control functions.
18
Step 3: Connecting the Audio Cords/HDMI Cord
Select one of the following patterns, A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver). This will enable you to listen
to sound.
[Speakers]
Rear (L)
Front (L)
Audio component with
a decoder
[Speakers]
Rear (R)
Front (R)
A
Hookups and Settings
Centre
HDMI cord
(not supplied)
to HDMI OUT
to LINE 2 OUT (R-AUDIO-L)
(white)
(red)
Audio/video cord
(yellow)*
: Signal flow
* The yellow plug is used for video signals (page 16).
(not supplied)
Subwoofer
or
to coaxial/HDMI digital input
Coaxial digital cord
(not supplied)
to DIGITAL OUT (COAXIAL)
DVD recorder
INPUT
VIDEO
(yellow)
(white)
(red)
L
AUDIO
R
TV, projector, or
audio component
B
A Digital audio input jack
If your audio component has a Dolby*1
Digital, DTS*2, or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effects.
If you connect a Sony audio component that
is compatible with the HDMI control
function, refer to the operating instructions
supplied with the audio component.
,continued
19
B Audio L/R (left/right) input jacks
This connection will use your TV’s or audio
component’s two speakers for sound.
z Hint
For correct speaker location, see the operating
instructions supplied with the connected
components.
b Notes
• Do not connect your TV’s audio output jacks to
the LINE IN (R-AUDIO-L) jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
• With connection B, do not connect the LINE IN
(R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L)
jacks to your TV’s audio output jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
• With connection A, after you have comple ted the
connection, make the appropriate settings in the
“Audio Out” setup (page 116). Otherwise, no
sound or a loud noise will come from your
speakers.
• When you connect the recorder to an audio
component using an HDMI cord, you will need to
do one of the following:
– Connect the audio component to the TV with
the HDMI cord, or
– Connect the recorder to the TV with a video
cord other than HDMI cord (component video
cord, S-video cord, or audio/video cord).
*1
Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are registered
trademarks of DTS, Inc.
Step 4: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the
recorder and TV mains leads (AC power
cords) into the mains. After you connect the
mains lead, you must wait for a short while before operating the recorder.
You can operate the recorder once the front
panel display lights up and the recorder enters
standby mode.
If you connect additional equipment to this
recorder (page 26), be sure to connect the
mains lead after all connections are complete.
1
to AC IN
2
to mains
20
Step 5: Preparing the
Remote
You can control the recorder using the
supplied remote. Insert two R6 (size AA)
batteries by matching the 3 and # ends on
the batteries to the markings inside the
battery compartment. When using the
remote, point it at the remote sensor on the
recorder.
Controlling TVs with the
remote
You can adjust the remote’s signal to control
your TV.
b Notes
• Depending on the connected unit, you may not be
able to control your TV with some or all of the
buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
Number
buttons
TV/DVD
Hookups and Settings
b Notes
• If the supplied remote interferes with your other
Sony DVD recorder or player, change the
command mode number for this recorder
(page 22).
• Use the batteries correctly to avoid possible
leakage and corrosion. Should leakage occur, do
not touch the liquid with bare hands. Observe the
following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an
extended period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid
inside the battery compartment, and insert new
batteries.
• Do not expose the remote sensor (marked on
the front panel) to strong light, such as direct
sunlight or a lighting apparatus . The recorder may
not respond to the remote.
• When you replace the batteries of the remote, the
code number and Command Mode may be reset
to the default setting. Set the appropriate code
number and Command Mode again.
DISPLAY
x
TV 2 +/–
TV PROG
+/–
TV [/1
TV t
1 Hold down TV [/1 located at the
bottom of the remote.
Do not press the [/1 button at the top of
the remote.
2 With TV [/1 pressed down, enter the
TV’s manufacturer code using the
number buttons.
For instance, to enter “09,” press “0” then
“9.” After you enter the last number,
release the TV [/1 button.
,continued
21
Code numbers of controllable TVs
If more than one code number is listed,
try entering them one at a time until you
find the one that works with your TV.
ManufacturerCode number
Sony01 (default)
Hitachi24
JVC33
Panasonic17, 49
Philips06, 08
Samsung71
Sanyo25
Thomson43
Toshiba38
The remote performs the following:
ButtonsOperations
TV [/1Turns your TV on or
TV 2 (volume)
+/–
TV PROG +/–Selects the
TV t (input
select)
off.
Adjusts the volume
of your TV.
programme position
on your TV.
Switches your TV’s
input source.
If you have a Sony DVD player
or more than one Sony DVD
recorder
If the supplied remote interferes with your
other Sony DVD recorder or player, set the
command mode number for this recorder and
the supplied remote to one that differs from
the other Sony DVD recorder or player after
you have completed “Step 6: Easy Setup.”
The default command mode setting for this
recorder and the supplied remote is DVD3.
You can check the current Command Mode
in the front panel display. For details, see
page 126.
The default command mode setting for this
recorder and the supplied remote is DVD3.
The remote does not function if different
command modes are set for the recorder and
remote. Set the same command mode.
Changing programme positions
of the recorder using the
remote
You can change programme positions of the
recorder using the number buttons.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between TV
mode and DVD mode. Press the TV/DVD
button when in stop mode or no menu appears
on the TV screen. Point your remote at the
recorder when using this button.
TV mode: switch to this when you use the
TV’s tuner mainly. When you start playback,
the input source for the TV is set to the
recorder automatically.
DVD mode: switch to this when you use the
recorder’s tuner mainly.
To check the current mode, press DISPLAY
(page 35).
22
Number
buttons
ENTER
Example: for channel 50
Press “5,” “0,” then press ENTER.
Step 6: Easy Setup
Make the basic adjustments by following the
on-screen instructions in “Easy Setup.”
Be careful not to disconnect the cables or exit
the “Easy Setup” function during this
procedure.
[/1
GUIDE
Auto Channel Setting
If you connect a TV to this recorder not
using SMARTLINK, select “Auto
Scan.” Then select your country/region
using </,, and press ENTER. The
programme position order will be set
according to the country/region you
select.
If you connect a TV to this recorder with
SMARTLINK, select “Download from
TV.” Then select your country/region
using </,, and press ENTER. The
tuner preset data will be downloaded
from your TV to this recorder. (For
details, refer to the operating instructions
supplied with your TV.)
Hookups and Settings
</M/m/,,
O
RETURN
ENTER
TV [/1
1 Turn on the recorder and your TV.
Then switch the input selector on your
TV so that the signal from the recorder
appears on your TV screen.
The “Language” display appears.
• If the “Language” display does not
appear, select “Easy Setup” in the
“Basic” setup from “Initial Setup” in
the System Menu (page 110).
2 Select a language for the on-screen
displays using M/m, and press
ENTER.
The initial settings message appears.
3 Select “Start” using M/m, and press
ENTER.
Follow the on-screen instructions to
make the following settings.
To skip this setting, select “Do not set.”
To set the programme positions
manually, see page 111.
Clock Setting
Select “Auto” when a programme
position in your local area broadcasts a
time signal. The “Auto Clock Setting”
display appears.
1 Select the programme position of the
station that carries a time signal
using </,.
2 Select “Start” using m, and press
ENTER.
If a clock signal cannot be found,
press O RETURN, and set the
clock manually.
Select “Manual” to set the clock
manually. The “Manual Clock Setting”
display appears.
1 Select the time zone for your area
using </,, and press m.
2 Select “On” if you are now on
summer time, and press ENTER.
3 Set the day, month, year, hour, and
minutes using </M/m/,, and
press ENTER to start the clock.
TV Screen Size (page 121)
If you have a wide-screen TV, select
“Wide (16:9).” If you have a standard
TV, select “Standard (4:3).” This will
determine how “wide-screen” images are
displayed on your TV.
,continued
23
Progressive
When you connect a progressive format
TV to this recorder using the
COMPONENT VIDEO OUT jacks,
select “Compatible.”
HDD caution messages
Read the HDD caution messages, and
press ENTER.
4 Select “Finish Setup” using M/m, and
press ENTER.
“Easy Setup” is completed.
To return to the previous step
Press O RETURN.
z Hint
If you want to run “Easy Setup” again, select “Easy
Setup” in the “Basic” setup from “Initial Setup” in
the System Menu (page 110).
Setting up the GUIDE Plus+®
system/set top box controller
Follow the steps below to set up the GUIDE
Plus+ system and set top box controller. The
GUIDE Plus+ system is available in the UK
only.
1 Press GUIDE.
The GUIDE Plus+ system “Basic Setup”
appears.
For users other than in the UK, go to
step 4.
2 Select “Postal Code,” and press
ENTER.
3 Enter your postal code using </M/m/
,, and press ENTER.
If “Country” is set to “Others,” you
cannot enter a postal code and the
GUIDE Plus+ system will not search for
a host channel.
4 Select “External Receiver 1,” and
press ENTER.
You can also select “External Receiver
2” or “External Receiver 3” if you have
connected additional set top box
receivers.
5 Press ENTER to select “Continue.”
6 Select the set top box receiver type
using M/m, and press ENTER.
7 Select the provider using M/m, and
press ENTER.
8 Select the receiver brand using M/m,
and press ENTER.
If you select “Other providers,” you can
select a receiver brand from a list of all
available brands.
If your receiver brand is not on the list,
select “???.”
The receiver brand list is automatically
updated, so your receiver may be
available at a later date. Select your brand
when it becomes available. Until then,
use “???.”
9 Select the connection you used for
your set top box receiver using M/m,
and press ENTER.
When the set top box receiver is
connected to the recorder using hookup
A with both an aerial cable and a SCART
cord, select either “Line1” or “Antenna.”
The display asks for confirmation.
10
Press ENTER to select “Continue.”
The Video Window switches to the
specified programme position.
24
11
Select “YES” using M/m, and press
ENTER.
The display asks for confirmation.
If the Video Window does not switch to
the specified programme position, select
“NO” and press ENTER until the Video
Window switches to the specified
programme position.
(In the UK only)
To receive GUIDE Plus+ system data
your recorder must be turned off
when not in use. If your recorder is
connected to a set top box receiver, be
sure to leave the set top box receiver
turned on. After initial setup, it may
take up to 24 hours to begin receiving
TV programme listings.
b Note
You cannot set tuner system or “OSD
Language” to a country/region or language
that is not supported by the GUIDE Plus+
system.
If you cannot get the recorder to control
your set top box receiver
Check the connection and position of the set
top box controller (page 14).
If your set top box receiver still does not
operate with this recorder, refer to the
instructions supplied with your set top box
receiver and contact your cable or satellite
company to see if they can provide you with
a compatible set top box receiver.
b Notes
• The list of external receivers controllable by the
GUIDE Plus+ system is upda ted constantly and is
distributed through GUIDE Plus+ system data
signals. Since the time your recorder has been
produced and the time you installed your recorder
for the first time, new external receiver codes
might have been added.
• If the external receiver is still not on the list or is
not controlled properly by the recorder, please
call Customer Support to report the brand and
model of your external receiver.
To fix the set top box controller to your set
top box receiver
Once you have confirmed that the set top box
controller controls your set top box receiver,
fix it in place.
1 Remove the backing on the double-sided
tape.
2 Attach it so that the set top box controller
is directly above the remote control
sensor on your set top box receiver.
To change the basic GUIDE Plus+ settings
1 Press GUIDE.
The GUIDE Plus+ system “Home
Screen” appears.
2 Select “Setup” in the Menu Bar using M/
,, and press ENTER.
The GUIDE Plus+ setup menu appears.
3 Select “Basic Setup” using M/m, and
press ENTER.
4 Repeat from step 2 of “Setting up the
GUIDE Plus+
controller” on page 24.
®
system/set top box
Hookups and Settings
25
Connecting a VCR or Similar Device
After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar
recording device to the LINE IN jacks of this recorder.
Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack)
(page 84).
For details, refer to the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording from Connected Equipment” on page 59.
Connecting to the LINE 1/DECODER jack
Connect a VCR or similar recording device to the LINE 1/DECODER jack of this recorder.
VCR
TV
to i LINE 1/DECODER
SCART cord (not supplied)
to T LINE 3 – TV
to SCART input
DVD recorder
b Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals through a VCR, you may not receive a clear image on your TV screen.
VCRDVD recorderTV
Be sure to connect your VCR to the DVD recorder and to your TV in the order shown below. To watch
video tapes, watch the tapes through a second line input on your TV.
Line input 1
VCRTV
• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 1/
DECODER jack.
• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the
TV/DVD button on the remote.
• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected
VCR.
DVD recorder
Line input 2
26
Connecting to the LINE 2 IN jacks on the front panel
Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the
equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
S VIDEO
OUTPUT
VIDEO
AUDI O
LR
Hookups and Settings
S-video cord
(not supplied)
to LINE 2 IN
: Signal flow
Audio/video cord
(not supplied)
DVD recorder
z Hint
When the connected equipment outputs only monaural sound, connect to only the L(MONO) and VIDEO
input jacks on the front of the recorder. Do not connect the R input jack.
b Notes
• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
• Do not connect the output jack of this recorder to another equipment’s input jack with the other
equipment’s output jack connected to the input jack of this recorder. This may cause noise (feedback).
• Do not connect more than one type of video cord between the recorder and your TV at the same time.
27
Connecting an External Decoder
You can watch or record external decoder (PAY-TV/Canal Plus analogue decoder)
programmes if you connect a decoder (not supplied) to the recorder. Disconnect the recorder’s
mains lead from the mains when connecting the decoder. Note that when you set “LINE 1 In”
to “Decoder” in step 7 of “Setting external decoder (PAY-TV/Canal Plus analogue decoder)
programme positions” (page 29), you will not be able to select “L1” because Line 1 will
become a dedicated line for the decoder.
Connecting a decoder
TV
to AERIAL IN
Aerial cable
(supplied)
to T LINE 3 – TV
to AERIAL OUTto i LINE 1/DECODER
to SCART input
SCART cord
(not supplied)
External decoder (PAY-TV/
Canal Plus analogue decoder)
SCART cord
(not supplied)
DVD recorder
28
Setting external decoder (PAYTV/Canal Plus analogue
decoder) programme positions
4 Select “LINE 3 Out,” and press
ENTER.
To watch or record PAY-TV/Canal Plus
analogue programmes, set your recorder to
receive the programme positions using the
on-screen display.
In order to set the programme positions
correctly, be sure to follow all of the steps
below.
Number
buttons
SYSTEM
MENU
</M/m/,,
O
RETURN
.>
ENTER
1 Press SYSTEM MENU.
The System Menu appears.
2 Select “Initial Setup,” and press
ENTER.
Hookups and Settings
5 Press M/m to select “Video” or
“RGB,” and press ENTER.
6 Select “LINE 1 In,” and press ENTER.
7 Press M/m to select “Decoder,” and
press ENTER.
8 Press O RETURN to return the cursor
to the left column.
9 Select “Tuner,” and press ENTER.
3 Select “Video In/Out,” and press
ENTER.
10
Select “Manual CH Setting,” and
press ENTER.
11
Select “Next Screen,” and press
ENTER.
,continued
29
12
Select your country/region, and press
ENTER.
Programme position
13
Select the desired programme
position using ./> or number
buttons.
14
Select “Channel” using M/m.
15
Select the external decoder
programme position using </,.
16
Select “Sound System” using M/m.
17
Press </, to select an available TV
system, B/G, D/K, I, or L.
To receive broadcasts in France, select
“L.”
18
Select “Decoder” using M/m.
19
Select “On” using </,, and press
ENTER.
To return to the previous step
Press O RETURN.
b Note
If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected decoder.
30
Loading...
+ 118 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.