Sony RDR-GXD500 User Manual

Download

Page 1

D:\DVD manual\Final\218839311_FM\01GB01COV.

01GB01.book Page 1 Mardi, 7. septembre 2004 9:41 09

master page=right

2-188-393-11(1)

DVD Recorder

Operating Instructions

RDR-GXD500

2-188-393-11(1)

Page 2

manual\Final\218839311_FM\01GB02WAR.fm

01GB01.book Page 2 Mardi, 7. septembre 2004 9:41 09

Important Information

Should you experience a problem with this recorder, please refer to the trouble shooting section on page 91. If you are unable to rectify the problem, contact the Sony Customer Information Centre on

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. The mains lead must only be changed at a qualified service shop.

08705 111 999

(Monday-Friday from 8:30am to 6:00pm)

Please ensure you have the following information available before calling the helpline:

Date of purchase: Serial number: Model number: Post code: Detailed fault

description: Signal strength

and signal

qualit

Note:

You can check the signal strength and signal quality using the menu system of this recorder. Page 29 explains how to display the main menu on screen,and page 81 explains how to obtain the signal strength display. The serial number and the model number are located on the rear of the recorder.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

CAUTION

The use of optical instruments w ith this product will increase eye hazard. As the laser beam used in this DVD recorder is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

CAUTION

ATTENTION

VORSICHT

ADVARSEL

VARNING

VARO!

This label is located on the laser protective housing inside the enclosure.

Notice for customers in the United Kingdom and Republic of Ireland

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS1362, (i.e., marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

D:\DVD

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO THE BEAM.

RADIATIONS LASER VISIBLES ET INVISIBLES DE CLASSE 3B EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU. KLASSE 3B SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN GEÖFFNET. DIREKTEN KONTAKT MIT DEM STRAHL VERMEIDEN.

SYNLIG OG USYNLIG LASERSTRÅLING AF KLASSE 3B VED ÅBNING. UNDGÅ DIREKTE UDSÆTTELSE FOR STRÅLING.

SYNLIG OG USYNLIG LASERSTRÅLING I KLASSE 3B NÅR DEKSEL ÅPNES. UNNGÅ DIREKTE EKSPONERING FOR STRÅLEN.

KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. UNDVIK ATT DIREKT EXPONERA DIG FÖR STRÅLNINGEN.

AVATTUNA LUOKAN 3B NÄKYVÄÄ JA NÄKYMÄTÖNTÄ LASERSÄTEILYÄ. VÄLTÄ SUORAA ALTISTUMISTA SÄTEELLE.

master page=left

Precautions

• This unit operates on 220 – 240 V AC, 50/60 Hz. Check that the unit’s operating voltage is identical with your local power supply.

• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.

RDR-GXD500

2-188-393-11(1)

Page 3

D:\DVD

manual\Final\218839311_FM\01GB02WAR.fm

01GB01.book Page 3 Mardi, 7. septembre 2004 9:41 09

master page=right

Precautions

This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 metres.

On safety

Should any solid object or liquid fall into the cabinet, unplug the recorder and have it checked by qualified personnel before operating it any further.

On power sources

• The recorder is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the recorder itself has been turned off.

• If you are not going to use the recorder for a long time, be sure to disconnect the recorder from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.

On placement

• Place the recorder in a location with adequate ventilation to prevent heat build-up in the recorder.

• Do not place the recorder on a soft surface such as a rug that might block the ventilation holes.

• Do not place the recorder in a confined space such as a bookshelf or similar unit.

• Do not place the recorder in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• Do not place the recorder in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the recorder and discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers.

• Do not place heavy objects on the recorder.

On recording

• Note that the contents of the recording cannot be compensated for under any and all conditions, including conditions that may arise due to a malfunction of this unit.

• Make trial recordings before making the actual recording.

Copyrights

• Television programmes, films, video tapes, discs, and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Copy guard function

Since the recorder has a copy guard function, programmes received through an external tuner (not supplied) may contain copy protection signals (copy guard function) and as such may not be recordable, depending on the type of signal.

IMPORTANT NOTICE

Caution: This recorder is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panels and projection televisions are especially susceptible to this.

If you have any questions or problems concerning your recorder, please consult your nearest Sony dealer.

About this manual

• Instructions in this manual describe the controls on the remote. You can also use the controls on the recorder if they have the same or similar names as those on the remote.

• The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen.

• The explanations regarding discs in this manual refer to discs created on this recorder. The explanations do not apply to discs that are created on other recorders and played back on this recorder.

RDR-GXD500

2-188-393-11(1)

Page 4

D:\DVD

manual\Final\218839311_FM\01GB01TOC.fm

01GB01.book Page 4 Mardi, 7. septembre 2004 9:41 09

master page=left

Table of Contents

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Ways to Use Your DVD Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Quick Guide to Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Hookups and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 2: Connecting the Aerial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Step 5: Connecting the Mains Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 6: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Step 7: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting a VCR or Similar Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Connecting to a Satellite or Digital Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Guide to Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Using the Title List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Using the “Disc Info” Screen (disc settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Checking the Play Information and Playing Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

How to Enter Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Guide to Digital Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

EPG (Electronic Programme Guide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Programme information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Viewing a digital text service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Favourites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Timer Recording (Standard/EPG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Checking/Changing/Cancelling Timer Settings (EPG) . . . . . . . . . . . . . . . . . . . . . . . .49

Checking/Changing/Cancelling Timer Settings (Timer List) . . . . . . . . . . . . . . . . . . . . 51

Recording Without the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Recording From Connected Equipment With a Timer (Synchro Rec) . . . . . . . . . . . . 55

Recording From Connected Equipment Without a Timer . . . . . . . . . . . . . . . . . . . . . . 57

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Chasing Playback/Simultaneous Rec and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Searching for a Title/Chapter/Track, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Playing MP3 Audio Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

RDR-GXD500

2-188-393-11(1)

Page 5

D:\DVD

manual\Final\218839311_FM\01GB01TOC.fm

01GB01.book Page 5 Mardi, 7. septembre 2004 9:41 09

master page=right

Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Before Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Editing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Creating and Editing a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Using the Setup Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Aerial Reception and Language Settings (Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Digital TV settings (DTV Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Recording and Parental Control Settings (Features) . . . . . . . . . . . . . . . . . . . . . . . . . 86

Parental Control (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Disc and Remote Control Settings/Factory Settings (Options) . . . . . . . . . . . . . . . . . . 89

Easy Setup (Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Self-diagnosis Function (When letters/numbers appear in the display) . . . . . . . . . . . 95

Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Digital TV Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

RDR-GXD500

2-188-393-11(1)

Page 6

D:\DVD

master page=left

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 6 Mardi, 7. septembre 2004 9:41 09

Ways to Use Your DVD Recorder

Quick access to recorded titles – Title List

, Display the Title List to see all of the titles

on the disc, including recording date, channel, recording mode and thumbnail image (page 30).

Play the beginning of a title while it is being recorded – Chasing Playback

, If you are using a DVD-RW (VR mode),

you can watch a programme from the beginning while it is being recorded (page 64).

Title List

Sort

Date Title Number

Recording

TITLE LIST

My Movies

ORIGINAL

1 AAB 13:00-14:00

Wed 5. 9 13:00 (1H00M) SP

2 DEF 20:00-21:00

Fri 17. 9 20:00 (1H00M) SLP

3 AAB 9:00-9:30

Sat 25. 9 9:00 (0H30M) EP

4 GHI 20:00-20:30

Sat 25. 9 20:00 (0H30M) SLP

1.5/4.7GB

AAB

DEF

AAB

GHI

Quick access to digital services

, An easy and convenient way to:

- View a complete list of all available channels.

- View descriptions of the programmes being broadcast now and next.

- Store your favourite channels.

- Set a programme to be recorded.

The match isn’t over yet, but I’ll start watching it from the beginning now.

RDR-GXD500

2-188-393-11(1)

Page 7

D:\DVD

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 7 Mardi, 7. septembre 2004 9:41 09

master page=right

Watching one title while recording another – Simultaneous Rec and Play

, If you are using a DVD-RW (VR mode),

you can watch a previously recorded programme while recording another programme on the same disc (page 64).

Recording

I think I’ll watch yesterday’s golf match now, even though I am recording a movie.

Creating your own programme – Playlist

, Record a programme on a DVD-RW (VR

mode), then delete, move and add scenes at will to create your own, original programme (page 72).

Original

Dynamic surround sound – TVS

, Enjoy virtual surround sound effects from

just your TV’s speakers with the TV Virtual Surround settings when playing a DVD VIDEO with multichannel audio tracks such as Dolby Digital (5.1ch) (page 61).

A list of recordable and playable discs is on page 8.

Playlist

RDR-GXD500

2-188-393-11(1)

Page 8

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 8 Mardi, 7. septembre 2004 9:41 09

Quick Guide to Disc Types

Recordable and playable discs

D:\DVD

master page=left

Type

DVD+RW

VR mode

DVDRW

Video mode

DVD+R

DVD-R

Disc Logo

Icon used in this manual

Video

Formatting (new discs)

Automatically formatted

Format in VR mode (page 33)

Format in Video mode (page 33)

Automatically formatted

Compatibility with other DVD players (finalizing)

Playable on DVD+RW compatible players (automatically finalized)

Playable only on VR mode compatible players (finalization unnecessary)

Playable on most DVD players (finalization necessary) (page 34)

Playable on DVD+R compatible players (finalization necessary) (page 34)

Playable on most DVD players (finalization necessary) (page 34)

Recordi

Rewrite (page 45)

Ye s

Usable disc versions (as of November 2004)

• 4x-speed or slower DVD+RWs

• 2x-speed or slower DVD-RWs (Ver.1.1, Ver.1.1 with CPRM*

)

• 8x-speed or slower DVD+Rs

• 8x-speed or slower DVD-Rs (Ver.2.0)

“DVD+RW,” “DVD-RW,” “DVD+R,” and “DVD-R,” are trademarks.

CPRM (Content Protection for Recordable Media) is a coding technology that protects copyrights for images.

Only if the recording mode is SP, HSP, or HQ, and “Line Rec Picture Size” is set to “16:9” (page 54).

Erasing titles does not free up disc space.

RDR-GXD500

2-188-393-11(1)

Page 9

D:\DVD

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 9 Mardi, 7. septembre 2004 9:41 09

Recording Features Editing Features

master page=right

zation

Rewrite (page 45)

Ye s

Auto Chapter (page 86)

Ye s

Manual Chapter (page 72)

Ye s

Record 16:9 sizes (page 54)

Ye s

Yes *

Change title name (page 69)

Ye s

Delete title (page 70)

Ye s

Yes *

A-B Erase (page 70)

Ye s

Playlist (page 72)

Ye s

Discs that cannot be recorded on

• 4x-speed compatible DVD-RWs (Ver. 1.2/4x)

• DVD-RWs (Ver. 1.0)

• DVD+RWs that are not 2.4x-speed compatible

• Dual layer discs

•8 cm discs

,continued

RDR-GXD500

2-188-393-11(1)

Page 10

D:\DVD

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 10 Mardi, 7. septembre 2004 9:41 09

Playable discs

master page=left

Type Characteristics

Disc Logo

DVD VIDEO

VIDEO CD

used in this manual

DVD

VCD

Discs such as movies that can be purchased or rented

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD/Super VIDEO CD format

Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased

CD-ROMs/CD-Rs/CD-RWs created on a PC or

Icon

DATA C D

DATA CD

similar device in music format containing MP3 audio tracks

Discs that cannot be played

• All CD-ROMs (including PHOTO CDs)

• CD-Rs/CD-RWs, other than those recorded in music CD format, MP3 format, or Video CD format

• Data part of CD-Extras

• DVD-ROMs

• DVD Audio discs

• DVD-RAMs

• HD layer on Super Audio CDs

• DVD VIDEOs with a different region code (page 11)

z Hint

This DVD recorder can play 8 cm CDs and 8 cm DVDs as well.

RDR-GXD500

2-188-393-11(1)

Page 11

D:\DVD

manual\Final\218839311_FM\01GB03GET.fm

01GB01.book Page 11 Mardi, 7. septembre 2004 9:41 09

master page=right

Note on playback operations of DVD VIDEOs/ VIDEO CDs

Some playback operations of DVD VIDEOs/ VIDEO CDs may be intentionally set by software producers. Since this recorder plays DVD VIDEOs/VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, see the instructions supplied with the DVD VIDEOs/ VIDEO CDs.

Region code (DVD VIDEO only)

Your recorder has a region code printed on the rear of the unit and will only play DVD VIDEOs (playback only) labelled with identical region codes. This system is used to protect copyrights. DVD VIDEOs labelled will also play on this

ALL

recorder. If you try to play any other DVD VIDEO, the message “Playback prohibited by region code.” will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be labelled even though playing the DVD VIDEO is prohibited by area restrictions.

RDR–XXXX

00V 00Hz

NO.

00W

Region code

0-000-000-00

Notes

• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-RWs/CD-Rs cannot be played on this recorder due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalized. For more information, see the operating instructions for the recording device.

• You cannot mix VR mode and Video mode on the same DVD-RW. To change the disc’s format, reformat the disc (page 33). Note that the disc’s contents will be erased after reformatting.

• You cannot shorten the time required for recording even with high-speed discs. Also, you cannot record on the disc if the disc is not 1x speed compatible.

• It is recommended that you use discs with “For Video” printed on their packaging.

• You cannot add new recordings to DVD-Rs or DVDRWs (Video mode) that contain recordings made on other DVD equipment.

• In some cases, you may not be able to add new recordings to DVD+RWs that contain recordings made on other DVD equipment. If you do add a new recording, note that this recorder will rewrite the DVD menu.

• If the disc contains PC data unrecognizable by this recorder, the data may be erased.

Music discs encoded with copyright protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

RDR-GXD500

2-188-393-11(1)

Page 12

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 12 Mardi, 7. septembre 2004 9:41 09

Hookups and Settings

Hooking Up the Recorder

Follow steps 1 to 7 to hook up and adjust the settings of the recorder.

Notes

• Plug cords securely to prevent unwanted noise.

• Refer to the instructions supplied with the components to be connected.

• You cannot connect this recorder to a TV that does not have a SCART or video input jack.

• Be sure to disconnect the mains lead of each component before connecting.

Step 1: Unpacking

Check that you have the following items:

• Audio/video cord (pinplug × 3 y pinplug × 3) (1)

• Mains lead (1)

• Aerial cable (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

master page=left

RDR-GXD500

2-188-393-11(1)

Page 13

D:\DVD

master page=right

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 13 Mardi, 7. septembre 2004 9:41 09

Step 2: Connecting the Aerial Cable

Connect the aerial cable by following the steps below. Do not connect the mains lead until you reach “Step 5: Connecting the Mains Lead” (page 19).

Hookups and Settings

to AERIAL IN

AERIAL

OUT

AERIAL

OUT

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

VIDEO

AUDIORL

S VIDEO

PCM/DTS/MPEG/ DOLBY DIGITAL

LINE 2 OUT

COAXIAL

VIDEO

AUDIORL

OPTICAL

S VIDEO

COMPONENT

VIDEO OUT

/ C

DVD recorder

~ AC IN

to AERIAL OUT

Aerial cable (supplied)

: Signal flow

1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the

recorder.

2 Connect AERIAL OUT of the recorder to the aerial input of your TV, using the supplied aerial

cable.

RDR-GXD500

2-188-393-11(1)

Page 14

D:\DVD

master page=left

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 14 Mardi, 7. septembre 2004 9:41 09

Step 3: Connecting the Video Cords

Select one of the following patterns A through D, according to the input jack on your TV monitor, projector, or AV amplifier (receiver). This will enable you to view pictures. Audio connections are explained in “Step 4: Connecting the Audio Cords” (page 17).

INPUT

VIDEO

AUDIO

TV, projector, or AV amplifier (receiver)

AERIAL

OUT

Audio/video cord (supplied)

to LINE 2 OUT (VIDEO)

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

COAXIAL

VIDEO

AUDIORL

S VIDEO

PCM/DTS/MPEG/ DOLBY DIGITAL

OPTICAL

To LINE 1 – TV

SCART cord (not supplied)

S-video cord (not supplied)

(yellow)

to LINE 2 OUT (S VIDEO)

LINE 2 OUT

VIDEO

AUDIORL

S VIDEO

(red) (blue)

Component video cord (not supplied)

COMPONENT

VIDEO OUT

/ C

(green)

S VIDEO

TV, projector, or AV amplifier (receiver)

DVD recorder

~ AC IN

to COMPONENT VIDEO OUT

COMPONENT

VIDEO IN

TV, projector, or AV amplifier (receiver)

INPUT

(green)

(blue)

(red)

: Signal flow

Note

Do not connect more than one type of video cord between the recorder and your TV at the same time.

RDR-GXD500

2-188-393-11(1)

Page 15

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 15 Mardi, 7. septembre 2004 9:41 09

master page=right

A Connecting to a SCART input jack

Connect using a SCART cord (not supplied) to the LINE 1-TV jack and your TV. Be sure to make the connections firmly to avoid hum and noise. See the operating instructions supplied with the TV to be connected. Also, when you set “Line1 Output” to “S Video” or “RGB” in step 9 of Easy Setup (page 24), use a SCART cord that conforms to the selected signal.

B Connecting to a video input jack

Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jack. You will enjoy standard quality images.

Yellow

White (L)

Red (R)

Yellow White (L)

Red (R)

C Connecting to an S VIDEO input

jack

Connect using an S-video cord (not supplied). You will enjoy high quality images.

D Connecting to component video

input jacks (Y, P

Connect the COMPONENT VIDEO OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate colour reproduction and high quality images.

Green

Blue

Red

When playing “wide screen” images

Some recorded images may not fit your TV screen. To change the aspect ratio, see page 82.

B/CB, PR/CR)

Green Blue Red

If you are connecting to a VCR

Connect your VCR to the LINE 3 jack on the recorder (page 26).

Notes

• When you connect the recorder to your TV via the SCART jacks, the TV’s input source is set to the recorder automatically when you start playback. If necessary, press TV/DVD on the remote to return the input to the TV.

• For correct SMARTLINK connection, you will need a SCART cord that has the full 21 pins. Refer to your TV’s instruction manual as well for this connection.

• If you connect this recorder to a TV with SMARTLINK, set “Line1 Output” to “Video” in step 9 of Easy Setup (page 24).

About the SMARTLINK features (for SCART connections only)

If the connected TV (or other connected equipment such as a set top box) complies with SMARTLINK, NexTView Link, MEGALOGIC* CINEMALINK*

LINK* automatically runs the SMARTLINK function after you complete the connection pattern A on page 14 (the SMARTLINK indicator lights up when you turn on your TV). You can enjoy the following SMARTLINK features.

• TV Direct Rec You can easily record what you are watching on your TV (page 53).

• One Touch Play You can turn on the recorder and TV, set the TV’s input to the recorder, and start playback with one touch of the H (play) button (page 59).

• One Touch Menu You can turn on the recorder and TV, set the TV to the recorder’s channel, and display the Title List menu with one touch of the TITLE LIST button (page 59).

• One Touch Timer You can turn on the recorder and TV, set the TV to the recorder’s channel, and display the timer programming menu with one touch of the TIMER button on the remote (page 47).

• Automatic Power Off The recorder will turn off automatically if the recorder is not used after you turn off the TV.

, EASYLINK*2,

, Q-Link*3, EURO VIEW

, or T-V LINK*5, this recorder

Hookups and Settings

,continued

RDR-GXD500

2-188-393-11(1)

Page 16

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 16 Mardi, 7. septembre 2004 9:41 09

• One Touch EPG You can turn on the recorder and TV, set the TV to the recorder’s channel, and display the Electronic Programme Guide screen with one touch of the (EPG) button on the remote.

• EPG Title Download The recorder will automatically download and set the title of the programme being recorded from LINE 1 according to the title name displayed in the EPG of the connected TV or STB.

“MEGALOGIC” is a registered trade mark of Grundig Corporation.

“EASYLINK” and “CINEMALINK” are trademarks of Philips Corporation.

“Q-Link” is a trademark of Panasonic Corporation.

“EURO VIEW LINK” is a trademark of Toshiba Corporation.

“T-V LINK” is a trademark of JVC Corporation.

z Hint

SMARTLINK also works with TVs or other equipment having EPG Timer Control, EPG Title Download, and Now Recording functions. For details, refer to the operating instructions supplied with your TV or other equipment.

master page=left

Notes

• The SMARTLINK features are available only when “Video” is selected in “Line1 Output.”

• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3 jack.

• Not all TVs respond to the functions above.

RDR-GXD500

2-188-393-11(1)

Page 17

D:\DVD

master page=right

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 17 Mardi, 7. septembre 2004 9:41 09

Step 4: Connecting the Audio Cords

Select one of the following patterns A or B, according to the input jack on your TV monitor, projector, or AV amplifier (receiver). This will enable you to listen to sound.

Hookups and Settings

(red)

(white)

(yellow)*

LINE 2 OUT

VIDEO

DIGITAL OUT

PCM/DTS/MPEG/ DOLBY DIGITAL

AUDIORL

AERIAL

OUT

COAXIAL

OPTICAL

S VIDEO

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

VIDEO

AUDIORL

to DIGITAL OUT (COAXIAL or OPTICAL)

Optical digital cord (not supplied)

[Speakers]

to optical digital input

Rear (L)

Audio/video cord (supplied)

to LINE 2 OUT (R-AUDIO-L)

LINE 2 OUT

COAXIAL

VIDEO

PCM/DTS/MPEG/ DOLBY DIGITAL

AUDIORL

OPTICAL

S VIDEO

(yellow)

(white)

(red)

COMPONENT

VIDEO OUT

/ C

DVD recorder

Coaxial digital cord (not supplied)

to coaxial digital input

INPUT

VIDEO

AUDIO

TV, projector, or AV amplifier (receiver)

~ AC IN

[Speakers]

Rear (R)

Front (L)

Front (R)

AV amplifier (receiver)

Centre

with a decoder

Subwoofer

: Signal flow

* The yellow plug is used for video signals (page 14).

z Hint

For correct speaker location, see the operating instructions supplied with the connected components.

Note

Do not connect your TV’s audio output jacks to the LINE IN (AUDIO L/R) jacks at the same time. This will cause unwanted noise to come from your TV’s speakers.

,continued

RDR-GXD500

2-188-393-11(1)

Page 18

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 18 Mardi, 7. septembre 2004 9:41 09

master page=left

A Connecting to audio L/R input

jacks

This connection will use your TV’s or stereo amplifier’s (receiver’s) two speakers for sound. Connect using the audio/video cord (supplied).

Yellow

White (L)

Red (R)

• Surround effect (page 60)

TV: Dynamic, Wide, Night

Stereo amplifier (receiver): Standard, Night

Note

Do not connect the LINE 4 IN (R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L) jacks to your TV’s audio output jacks at the same time. This will cause unwanted noise to come from your TV’s speakers.

Yellow White (L)

Red (R)

B Connecting to a digital audio

input jack

If your AV amplifier (receiver) has a Dolby*1 Digital, DTS* digital input jack, use this connection. Connect using a coaxial or optical digital cord (not supplied).

Coaxial cord

Optical cord

• Surround effect Dolby Digital (5.1ch), DTS (5.1ch), MPEG audio (5.1ch)

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Notes

• After you have completed connection B, make the appropriate settings under “Audio Connection” in Easy Setup (page 22). If your AV amplifier (receiver) has an MPEG audio decoder function, set “MPEG” to “MPEG” in Audio Setup (page 85). Otherwise, no sound or a loud noise will come from your speakers.

• The surround sound effects of this recorder cannot be used with connection B.

, or MPEG audio decoder and a

RDR-GXD500

2-188-393-11(1)

Page 19

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 19 Mardi, 7. septembre 2004 9:41 09

master page=right

Step 5: Connecting the Mains Lead

Connect the supplied mains lead to the AC IN terminal of the recorder. Then plug the recorder and TV mains leads (power cords) into the mains. After you connect the mains lead, you must wait for a short while before operating the recorder. You can operate the recorder once the front panel display lights up and the recorder enters standby mode. If you connect additional equipment to this recorder (page 26), be sure to connect the mains lead after all connections are complete.

~ AC IN

to AC IN

to mains

Step 6: Preparing the Remote

You can control the recorder using the supplied remote. Insert two R6 (size AA) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the recorder.

Notes

• If the supplied remote interferes your other Sony DVD recorder or player, change the command mode number for this recorder (page 21).

• Use the batteries correctly to avoid possible leakage and corrosion. Do not touch the liquid with bare hands should leakage occur. Observe the following: – Do not use a new battery with an old battery, or

batteries of different manufacturers. – Do not attempt to recharge the batteries. – If you do not intend to use the remote for an extended

period of time, remove the batteries. – If battery leakage occurs, wipe out any liquid inside

the battery compartment, and insert new batteries.

• Do not expose the remote sensor (marked on the front panel) to strong light, such as direct sunlight or lighting apparatus. The recorder may not respond to the remote.

Hookups and Settings

,continued

RDR-GXD500

2-188-393-11(1)

Page 20

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 20 Mardi, 7. septembre 2004 9:41 09

master page=left

Controlling TVs with the remote

You can adjust the remote’s signal to control your TV. If you connected the recorder to an AV amplifier (receiver), you can use the supplied remote to control the AV amplifier’s (receiver’s) volume.

Notes

• Depending on the connected unit, you may not be able to control your TV or AV amplifier (receiver) with some or all of the buttons below.

• If you enter a new code number, the code number previously entered will be erased.

• When you replace the batteries of the remote, the code number may be reset to the default setting. Set the appropriate code number again.

TV/DVD switch

"/1

Number buttons, SET/-/--

1 2 3

4 5 6

7 8 9

PROG +/–

2 +/–

t, TV/DVD

1 Slide the TV/DVD switch to TV. 2 Hold down [/1. 3 Enter your TV’s manufacturer code (see

“Code numbers of controllable TVs” below) using the number buttons.

4 Release [/1.

When the TV/DVD switch is set to TV, the remote performs the following:

[/1 Turns your TV on or off 2 (volume) +/– Adjusts the volume of your

PROG +/– Selects the programme

t (TV/video) Switches your TV’s input

Number buttons and SET, -/--*

position on your TV

source Selects the programme

position on your TV

* If you use the number buttons to select the TV’s

programme position, press -/-- followed by the number buttons for two-digit numbers.

To operate the TV/DVD button (for SCART connections only)

The TV/DVD button switches between the recorder and the last input source selected on the TV. Point your remote at the recorder when using this button. The button works even if the TV/DVD switch is set to DVD. When you connect the recorder to the TV via the SCART jacks, the input source for the TV is set to the recorder automatically when you start playback. To watch another source, press the TV/ DVD button to switch the TV’s input source.

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Manufacturer Code number

Sony 01 (default) Aiwa 01 (default) Grundig 11 Hitachi 23, 24, 72 Loewe 06, 45 Nokia 15, 16, 69, 73 Panasonic 17, 49 Philips 06, 07, 08, 23, 45, 72 Saba 12, 13, 36, 43, 74, 75 Samsung 06, 22, 23, 71, 72 Sanyo 25 Sharp 29 Telefunken 12, 13, 36, 43, 74, 75 Thomson 12, 13, 43, 74, 75 Toshiba 38 LG 06 JVC 33

RDR-GXD500

2-188-393-11(1)

Page 21

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 21 Mardi, 7. septembre 2004 9:41 09

master page=right

Controlling the volume of your AV amplifier (receiver) with the remote

TV/DVD switch

"/1

1 2 3

Number buttons

4 5 6

7 8 9

2 +/–

1 Slide the TV/DVD switch to DVD. 2 Hold down [/1, and enter the

manufacturer code (see the table below) for your AV amplifier (receiver) using the number buttons.

3 Release [/1.

The 2 (volume) +/– buttons control the AV amplifier’s volume. If you want to control the TV’s volume, slide the TV/DVD switch to TV.

If you have a Sony DVD player or more than one Sony DVD recorder

If the supplied remote interferes with your other Sony DVD recorder or player, set the command mode number for this recorder and the supplied remote to one that differs from the other Sony DVD recorder or player. The default command mode setting for this recorder and the supplied remote is DVD3.

1 2 3

4 5 6

7 8 9

SYSTEM MENU

O RETURN

M/m, ENTER

Hookups and Settings

z Hint

If you want to control the TV’s volume even when the TV/DVD switch is set to DVD, repeat the steps above and enter the code number 90 (default).

Code numbers of controllable AV amplifiers (receivers)

If more than one code number is listed, try entering them one at a time until you find the one that works with your AV amplifier (receiver).

Manufacturer Code number

Sony 78, 79, 80, 91 Denon 84, 85, 86 Kenwood 92, 93 Onkyo 81, 82, 83 Pioneer 99 Sansui 87 Technics 97, 98 Yamaha 94, 95, 96

COMMAND MODE

1 Press SYSTEM MENU.

The System Menu appears.

2 Select “SETUP,” and press ENTER.

SETUP

Settings

Clock

DTV Settings

Language

Video

Audio

Features

Password

Options

Easy Setup

,continued

RDR-GXD500

2-188-393-11(1)

Page 22

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 22 Mardi, 7. septembre 2004 9:41 09

3 Select “Options,” and press ENTER.

SETUP

Settings

DTV Settings

Video Audio

Features

Password

Options

Easy Setup

Format DVD : Dimmer : Auto Display : Command Mode : Factory Setup

VR Normal On DVD3

4 Select “Command Mode,” and press

ENTER.

master page=left

Step 7: Easy Setup

Follow the steps below to make the minimum number of basic adjustments for using the recorder. If you do not complete Easy Setup, it will appear each time you turn on your recorder. Settings are made in the following order.

z Hint

Information on coverage and aerial upgrades can be found on the following Freeview website, www.freeview.co.uk

SETUP

Settings

DTV Settings

Video

Audio

Features

Password

Options

Easy Setup

Format DVD : Dimmer : Auto Display : Command Mode : Factory Setup

DVD1 DVD2 DVD3

VR Normal On DVD3

5 Select the Command mode (DVD1, DVD2,

or DVD3), and press ENTER.

6 Slide the COMMAND MODE switch on the

remote so it matches the mode you selected above.

To return to the previous step

Press O RETURN.

Auto Tune Setup

Clock Setup

TV Type Setup

Video Connection Setup

Audio Connection Setup

Finished!

O RETURN

1 2 3

4 5 6

7 8 9

"/1

PROG +/–

</M/m/,, ENTER

1 Turn on the TV. 2 Press [/1.

The recorder turns on.

RDR-GXD500

2-188-393-11(1)

Page 23

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 23 Mardi, 7. septembre 2004 9:41 09

master page=right

3 Switch the input selector on your TV so that

the signal from the recorder appears on your TV screen.

“Initial settings necessary to operate the DVD recorder will be made. You can change them later using Setup. Before you start, check that you have made all necessary connections. If you have preset any timer recordings they will be erased.” appears.

• If this message does not appear, select “Easy

Setup” from “SETUP” in the System Menu to run Easy Setup. For details, see “Settings and Adjustments” (page 76).

4 Select “Start,” and press ENTER.

The Auto Tune display appears showing a tuning progress bar and the number of channels found.

EASY SETUP Auto Tune 1/5

Number of channels found

Searching ...

When Auto Tune has ended, a completion display appears indicating the number of TV and Radio channels that have been found and stored.

EASY SETUP Auto Tune 1/5

Number of channels found

Number of Radio Channels

Tuning has sucessfully completed

Number of TV Channels

5 In case the current time and date could not

be set automatically thanks to your local stations time signal broadcasts, the display for setting the clock manually appears.

EASY SETUP Clock

The clock was not set automatically. Set the time and date manually.

Tue 14 9 21 00:2004

Set the clock manually using </M/m/,.

6 Press ENTER.

The TV Type Setup Display appears.

EASY SETUP TV Type 2/5

Select your TV screen type.

16 : 9 4 : 3 Letter Box 4 : 3 Pan Scan

7 Select the setting that matches your TV

type.

“16:9”: For wide-screen TVs or standard TVs with a wide screen mode. “4:3 Letter Box”: For standard TVs. Displays “wide screen” pictures with bands on the upper and lower sections of the screen. “4:3 Pan Scan”: For standard TVs. Automatically displays “wide screen” pictures on the entire screen and cuts off the sections that do not fit.

Hookups and Settings

To set the channels manually, see page 80.

For details, see “TV Type” on page 82.

8 Press ENTER.

The Setup Display for the component out jacks appears.

9 Select an option.

Select “On” if you are using the COMPONENT VIDEO OUT jacks. Otherwise, select “Off.”

RDR-GXD500

2-188-393-11(1)

,continued

Page 24

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 24 Mardi, 7. septembre 2004 9:41 09

master page=left

10Press ENTER.

The Setup Display for selecting the type of video signal output from the LINE 1-TV jack appears.

EASY SETUP Line1 Output 4/5

Select the Line1 output signal.

Video S Video RGB

11Select the type of signal you want to output

from the LINE1-TV jack.

“Video”: Outputs video signals. “S Video”: Outputs S video signals. “RGB”: Outputs RGB signals. Note that if you select “On” in step 9, you cannot select “RGB.”

• If you select “S Video” or “RGB,” SMARTLINK will be deactivated.

12Press ENTER.

The Setup Display for selecting the type of jack used to connect to your amplifier (receiver) appears.

EASY SETUP Audio Connection 5/5

Is this recorder connected to an amplifier (receiver)? Select the type of jack you are using.

Yes :

LINE2 OUT(R-AUDIO-L)

Yes :

DIGITAL OUT

14Select the type of Dolby Digital signal you

wish to send to your amplifier (receiver).

EASY SETUP

Dolby Digital

D-PCM Dolby Digital

Audio Connection 5/5

If your AV amplifier (receiver) has a Dolby Digital decoder, select “Dolby Digital.” Otherwise, select “D-PCM.”

15Press ENTER.

The Setup Display for the DTS signal appears.

On Off

Audio Connection 5/5

EASY SETUP

DTS

16Select whether or not you wish to send a

DTS signal to your amplifier (receiver), and press ENTER.

If your AV amplifier (receiver) has a DTS decoder, select “On.” Otherwise, select “Off.”

17Press ENTER when “Finish” appears.

Easy Setup is finished. All connections and setup operations are complete.

13Select the type of jack (if any) you are

using to connect to an amplifier (receiver), and press ENTER.

If you did not connect an AV amplifier (receiver), select “No,” then go to step 16. If you connected an AV amplifier (receiver) using just an audio cord, select “Yes: LINE 2 OUT (R-AUDIO-L),” then go to step 17. If you connected an AV amplifier (receiver) using either a digital optical or coaxial cord, select “Yes: DIGITAL OUT.”

EASY SETUP

Easy Setup is finished.

Finish

To return to the previous step

Press O RETURN.

z Hints

• If your AV amplifier (receiver) has an MPEG audio decoder, set “MPEG” to “MPEG” (page 86).

• If you want to run Easy Setup again, select “Easy Setup” in the Setup Display (page 90).

RDR-GXD500

2-188-393-11(1)

Page 25

D:\DVD

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 25 Mardi, 7. septembre 2004 9:41 09

Note

To record TV programmes using the timer, you must set the clock accurately.

master page=right

Hookups and Settings

RDR-GXD500

2-188-393-11(1)

Page 26

D:\DVD

master page=left

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 26 Mardi, 7. septembre 2004 9:41 09

Connecting a VCR or Similar Device

After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar recording device to the LINE IN jacks of this recorder. See also the instruction manual supplied with the connected equipment. To record on this recorder, see “Recording From Connected Equipment Without a Timer” (page 57).

Connecting to the LINE 3 jack

Connect a VCR or similar recording device to the LINE 3 jack of this recorder.

VCR

SCART cord (not supplied)

to SCART input

PCM/DTS/MPEG/ DOLBY DIGITAL

to i LINE3

LINE 2 OUT

COAXIAL

VIDEO

AUDIORL

OPTICAL

S VIDEO

COMPONENT

VIDEO OUT

/ C

DVD recorder

~ AC IN

to i LINE1-TV

AERIAL

OUT

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

VIDEO

AUDIORL

S VIDEO

Notes

• Pictures containing copy protection signals that prohibit any copying cannot be recorded.

• If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen.

VCRDVD recorder TV

Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV.

Line input 1

VCR

DVD recorder

• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3 jack.

• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the TV/DVD button on the remote.

• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected VCR.

Line input 2

RDR-GXD500

2-188-393-11(1)

Page 27

D:\DVD

master page=right

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 27 Mardi, 7. septembre 2004 9:41 09

Connecting to the LINE 2 IN or LINE 4 IN jacks

Connect a VCR or similar recording device to the LINE 2 IN or LINE 4 IN jacks of this recorder. If the equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.

VCR, etc.

OUTPUT

S VIDEO

VIDEO

AUDIO

Hookups and Settings

Audio/video cord (not supplied)

DVD recorder (front)

to LINE 2 IN

S VIDEO cord (not supplied)

(rear)

AERIAL

OUT

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

VIDEO

AUDIORL

S VIDEO

PCM/DTS/MPEG/ DOLBY DIGITAL

LINE 2 OUT

COAXIAL

AUDIORL

OPTICAL

COMPONENT

VIDEO OUT

/ C

VIDEO

S VIDEO

/ C

~ AC IN

to LINE 4 IN

VCR, etc.

: Signal flow

z Hint

When the connected equipment outputs only monaural sound, use audio cables that distribute monaural sounds to left/ right channels (not supplied).

Notes

• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.

• Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output jack connected to the input jack of this recorder. Noise (feedback) may result.

• Do not connect more than one type of video cord between the recorder and your TV at the same time.

RDR-GXD500

2-188-393-11(1)

Page 28

D:\DVD

master page=left

manual\Final\218839311_FM\01GB04BAS.fm

01GB01.book Page 28 Mardi, 7. septembre 2004 9:41 09

Connecting to a Satellite or Digital Tuner

Connect a satellite or digital tuner to this recorder using the LINE 3 jack. Disconnect the recorder’s mains lead from the mains when connecting the tuner. To use the Synchro-Rec function, see below.

to SCART input

SCART cord (not supplied)

Satellite tuner, etc.

to i LINE1-TV

AERIAL

OUT

LINE 1 - TV LINE 3

LINE 4 IN DIGITAL OUT

VIDEO

AUDIORL

If the satellite tuner can output RGB signals

This recorder accepts RGB signals. If the satellite tuner can output RGB signals, connect the TV SCART connector on the satellite tuner to the LINE 3 jack, and set “Line3 Input” of “Scart Setting” to “Video/RGB” in Video Setup (page 83). Note that this connection and setup disable the SMARTLINK function. If you want to use the SMARTLINK function with a compatible set top box, see the instructions supplied with the set top box.

If you want to use the Synchro Rec function

This connection is necessary to use the Synchronized Recording function. See “Recording From Connected Equipment With a Timer (Synchro Rec)” (page 55).

to i LINE3

LINE 2 OUT

COAXIAL

VIDEO

PCM/DTS/MPEG/ DOLBY DIGITAL

AUDIORL

OPTICAL

S VIDEO

DVD recorder

COMPONENT

VIDEO OUT

/ C

~ AC IN

Set “Line3 Input” of “Scart Setting” in Video Setup (page 83) according to the specifications of your satellite tuner. See your satellite tuner’s instructions for more information. If you are using a B Sky B tuner, be sure to connect the tuner’s VCR SCART jack to the LINE 3 jack. Then set “Line3 Input” of “Scart Setting” according to the specifications of the VCR SCART jack on your satellite tuner.

Notes

• Synchronized Recording does not work with some tuners. For details, see the tuner’s operating instructions.

• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected tuner.

RDR-GXD500

2-188-393-11(1)

Page 29

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 29 Mardi, 7. septembre 2004 9:41 09

Guide to Displays

Using the On-Screen Menus

RWVR-RW

VCD

DATA CD

This section introduces the System Menu, TOOLS menu, and sub-menu. By using these displays, you can perform most of the recorder’s operations.

Number buttons, SET

SYSTEM MENU

O RETURN

System Menu

The System Menu appears when you press SYSTEM MENU, and provides entries to all of the recorder’s main functions, such as timer recording and setup. Select an option by pressing M/m and ENTER.

Video

1 2 3

4 5 6

7 8 9

DVD

TOOLS

</M/m/,, ENTER

master page=right

B EPG (page 38):

Turns on the Electronic Programme Guide display that allows you to view a complete list of all available channels and to set a programme to be recorded.

C TIMER LIST (page 51):

Turns on the Timer List menu, which allows you to check, change, or cancel timer settings.

D SETUP (page 76):

Turns on the Setup Display, which allows you to set up the recorder to suit your preferences.

Sub-menu

The sub-menu appears when you select an item from a list menu (e.g. a title from the Title List menu), and press ENTER. The sub-menu displays options applicable only to the selected item. The displayed options differ depending on the situation and disc type. Select an option by pressing M/m and ENTER.

Example: The Title List menu

My Movies

1.5/4.7GB

15. 9

Wed

Play

17. 9

Fri

Play Beginning

25. 9

Sat

Erase

Protect

25. 9

Sat

Title Name

Fri

15.10

Set Thumbnail

Tue

19.10

A-B Erase

Tue

26.10

Thu

28.10

Options for the selected item

Sort

Date Title Number

TITLE LIST

ORIGINAL

1 New Generation

2 American Soccer

3 Opera

4 Passion for... Writing

5 Wheater

6 To Be a Millionaire

7 Regional News

8 Passengers to Lisboa

Guide to Displays

SYSTEM MENU

TITLE LIST

EPG

TIMER LIST

SETUP

A TITLE LIST (page 30):

Turns on the Title List menu, which shows recorded titles on the disc.

,continued

RDR-GXD500

2-188-393-11(1)

Page 30

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 30 Mardi, 7. septembre 2004 9:41 09

master page=left

TOOLS

The TOOLS menu appears when you press TOOLS, and displays options applicable to the entire disc (e.g. disc protection), recorder (e.g. audio settings during recording), or multiple items on a list menu (e.g. erasing multiple titles). The displayed options differ depending on the situation and disc type. Select the option by pressing M/m and ENTER.

Example 1: When you press TOOLS while the Title List menu is turned on.

My Movies

TITLE LIST

ORIGINAL

1 New Generation

Sort

Date

2 American Soccer

Disc Info

Title

3 Opera

Erase Titles

Number

4 Passion for... Writing

Playlist

5 Wheater

Create Playlist

6 To Be a Millionaire

TOOLS

7 Regional News

8 Passengers to Lisboa

Options for the disc or menu

Example 2: When you press TOOLS while a DVD-RW (VR mode) is playing.

Stop

Disc Info

Erase

Protect

TOOLS

Wed

Fri

Sat

Fri

Tue

Thu

1.5/4.7GB

15. 9

17. 9

25. 9

15.10

19.10

26.10

28.10

Using the Title List

RWVR-RW

Video

The titles of programmes recorded on a disc are displayed in the Title List.

1 2 3

4 5 6

7 8 9

TITLE LIST

CURSOR MODE

TOOLS </M/m/,, ENTER ZOOM +/–

1 Press Z (open/close), and place a disc on

the disc tray.

With the recording side facing down

Options for the disc or picture

To return to the previous display

Press O RETURN.

2 Press Z (open/close) to close the disc

tray.

Wait until “LOAD” disappears from the front panel display.

3 Press TITLE LIST.

To show the list in greater detail (zoom), press ZOOM+.

RDR-GXD500

2-188-393-11(1)

Page 31

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 31 Mardi, 7. septembre 2004 9:41 09

master page=right

Standard Title List (Example: DVD-RW in VR mode)

My Movies

Sort

Date Title Number

TITLE LIST

ORIGINAL

1 New Generation

2 American Soccer

3 Opera

4 Passion for... Writing

5 Wheater

6 To Be a Millionaire

7 Regional News

8 Passengers to Lisboa

Wed

Fri

Sat

Fri

Tue

Thu

1.5/4.7GB

15. 9

17. 9

25. 9

15.10

19.10

26.10

28.10

“Zoomed” Title List

My Movies

TITLE LIST

ORIGINAL

Sort

Date Title Number

1 American Soccer

Wed 5. 9 13:00 (1H00M) SP

2 Passengers to Lisboa

Fri 17. 9 20:00 (1H00M) SLP

3 Wheater

Sat 25. 9 9:00 (0H30M) EP

4 Regional News

Sat 25. 9 20:00 (0H30M) SLP

A Title type (DVD-RW in VR mode only):

Displays the title type, Original or Playlist.

B Sort buttons:

Sorts the title order (see below).

C Zooming indicator:

Shows the current zoom status.

D Disc name (page 33) E Disc space (remainder/total) F Title information:

Displays the title number, title name, and recording date. z (red): Indicates that the title is currently being recorded.

: Indicates the protected title.

G Scroll bar:

Appears when all of the titles do not fit on the list. To view the hidden titles, press M/m.

H Title’s thumbnail picture

1.5/4.7GB

AAB

DEF

AAB

GHI

To scroll the list display by page (Page mode)

Press CURSOR MODE while the list display is turned on. The display enters Page mode. Each time you press M/m, the entire Title List changes to the next/previous page of titles. To return to the Cursor mode, press CURSOR MODE again.

About the Title List for DVD-RWs (VR mode)

You can switch the Title List to show Original or Playlist. While the Title List menu is turned on, press TOOLS and select either “Original” or “Playlist,” and press ENTER. “PLAYLIST” appears on the front panel display when “Playlist” is selected. For details, see “Edit options for DVD-RWs (VR mode)” (page 68).

To change the title order (Sort)

Press < while the Title List menu is turned on to move the cursor to the Sort column. Press M/m to select the item, and press ENTER.

Order Sorted

Date in order of when the titles were

recorded. The title that is recorded

most recently is listed at the top. Title in alphabetical order. Number in order of recorded title number.

To change a title thumbnail picture (Thumbnail) (DVD-RW in VR mode only)

You can select a favourite scene for the thumbnail picture shown in the Title List menu.

1 Press TITLE LIST while a disc is in the

recorder and press ZOOM+.

2 Select a title whose thumbnail picture you

want to change, and press ENTER.

3 Select “Set Thumbnail” from the sub-menu,

and press ENTER. The selected title starts to play in the background.

4 While watching the playback picture, press

H, X, or m/M to select the scene you want to set for a thumbnail picture, and press ENTER. The scene is set for the title’s thumbnail picture.

Guide to Displays

To turn off the Title List

Press TITLE LIST.

,continued

RDR-GXD500

2-188-393-11(1)

Page 32

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 32 Mardi, 7. septembre 2004 9:41 09

z Hint

After recording, the first scene of the recording (the title) is automatically set as the thumbnail picture.

Notes

• The Title List may not appear for discs created on other DVD recorders.

• Letters that cannot be displayed are replaced with an “*.”

• Title thumbnail pictures are displayed only on this recorder.

• It may take a few seconds for the thumbnail pictures to be displayed.

• After editing, the title thumbnail picture may change to the first scene of the recording (title).

master page=left

Using the “Disc Info” Screen (disc settings)

RWVR-RW

With the Disc Information display, you can check the disc type and remaining disc space. Also, you can perform operations such as formatting and finalizing (page 33).

Video

1 2 3

4 5 6

7 8 9

TOOLS

</M/m/,, ENTER

1 Press Z (open/close), and place a disc on

the disc tray.

With the recording side facing down

2 Press Z (open/close) to close the disc

tray.

Wait until “LOAD” disappears from the front panel display.

3 Press TOOLS.

The TOOLS menu appears.

4 Select “Disc Info,” and press ENTER.

Items in the display differ depending on the disc type or recording format.

RDR-GXD500

2-188-393-11(1)

Page 33

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 33 Mardi, 7. septembre 2004 9:41 09

master page=right

Example: DVD-RW (VR mode)

Disc Information

DiscName Movie

Media DVD-RW Format VR Title no. Original 3 / Playlist 2 Protected Not Protected Date 15.9.2003 ~ 28.10.2003

HQ : 0H30M

HSP : 0H45M

LP : 1H30M

Remainder

EP : 2H00M

SLP : 3H00M

SP : 1H00M

2. 3 / 4. 7GB

Disc Name

Protect Disc

Finalize

Erase All

Format

A “Disc Name” B “Media”: Disc type C “Format”: Recording format type (DVD-

RW only)

D “Title no.”: Total number of titles E “Protected”: Indicates whether protection is

set (DVD-RW in VR mode only)

F “Date”: Dates of when the oldest and the

most recent titles were recorded

G “Continuous Rem. Time”/“Remainder”

(approximate)

• The longest continuous recording time in

each of the recording modes

• Disc space bar

• Remaining disc space/total disc space

H Disc setting buttons (page 33)

“Disc Name” “Protect Disc” “Finalize”/“Unfinalize” “Erase All” “Format” Available settings differ depending on the disc type.

Labelling, protecting, or formatting a disc

RWVR-RW

Video

You can execute options effective for the entire disc using the Disc Information display.

1 Press TOOLS while the disc is in the

recorder.

The TOOLS menu appears.

2 Select “Disc Info,” and press ENTER.

Example: When the inserted disc is a DVDRW (VR mode).

Disc Information

DiscName

Media DVD-RW Format VR Title no. Original 3 / Playlist 2 Protected Not Protected Date 15. 9. 2003 ~ 28. 10. 2003

HQ : 0H30M

HSP : 0H45M

LP : 1H30M

Remainder

EP : 2H00M

SLP : 3H00M

SP : 1H00M

2. 3 / 4. 7GB

Disc Name

Protect Disc

Finalize

Erase All

Format

3 Select an option, and press ENTER.

“Disc Name”: Labels a disc. Enter the disc name in the “Input Disc Name” display (page 37). “Protect Disc” (DVD-RW in VR mode only): Protects all titles on the disc. To cancel the protection, select “Don’t Protect.” “Erase All” (DVD+RW/DVD-RW only): Erases all titles on the disc (except the protected titles). “Format” (DVD+RW/DVD-RW only): Erases all contents of the disc to make a blank disc. For DVD-RWs, select a recording format (VR or Video) according to your needs.

Guide to Displays

z Hint

For DVD+RWs and DVD-RWs (Video mode), you can check free space and title location on the disc using the Disc Map display (page 71).

Note

On this model, 1 GB (read “gigabyte”) is equivalent to 1 billion bytes. The larger the number, the larger the disc space.

z Hints

• You can set protection for individual titles (page 69).

• By reformatting, you can change the recording format on DVD-RWs, or record again on DVD-RWs (Video mode) that have been finalized.

Note

You can enter up to 64 characters for a disc name. The disc name may not appear when the disc is played on other DVD equipment.

,continued

RDR-GXD500

2-188-393-11(1)

Page 34

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 34 Mardi, 7. septembre 2004 9:41 09

master page=left

Finalizing a disc (preparing a disc for playback on other equipment)

RWVR-RW

Finalizing is necessary when you play discs recorded with this recorder on other DVD equipment. When you finalize a DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R, a DVD menu will be automatically created, which can be displayed on other DVD equipment. Before finalizing, check the differences between the disc types in the table below.

Differences between the disc types

RWVR

Discs are automatically finalized when

removed from the recorder. However, you may need to finalize the disc for certain DVD equipment, or if the recording time is short. You can edit or record on the disc even after finalizing.

Finalizing is unnecessary when playing a disc on VR format compatible equipment. Even if your other DVD equipment is VR format compatible, you may need to finalize the disc, especially if the recording time is short. You can edit or record on the disc even after finalizing.

Finalizing is necessary when playing on

Video

any equipment other than this recorder. After finalizing, you cannot edit or record on the disc. If you want to record on it again, reformat the disc (page 33). However, all recorded contents will be erased.

Finalizing is necessary when playing on

any equipment other than this recorder.

After finalizing, you cannot edit or record on the disc.

Video

1 Press TOOLS while the disc is in the

recorder.

The TOOLS menu appears.

2 Select “Disc Info,” and press ENTER.

The Disc Information display appears.

3 Select “Finalize,” and press ENTER.

The display shows the approximate time required for finalizing and asks for confirmation.

Finalize

About xx min is needed for finalizing this disc. Cannot cancel finalizing during transaction. Do you want to finalize?

OK Cancel

4 Select “OK,” and press ENTER.

The recorder starts finalizing the disc.

To unfinalize a DVD-RW (VR mode)

If you cannot record or edit on a DVD-RW (VR mode) that has been finalized with other DVD equipment (a message appears), unfinalize the disc by selecting “Unfinalize” in step 3 above.

z Hint

You can check whether the disc has been finalized or not. If you cannot select “Finalize” in step 3 above, the disc has already been finalized.

Notes

• Depending on the condition of the disc, recording, or the DVD equipment, discs may not play even if the discs are finalized.

• The recorder may not be able to finalize the disc if it was recorded on another recorder.

RDR-GXD500

2-188-393-11(1)

Page 35

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 35 Mardi, 7. septembre 2004 9:41 09

Checking the Play

master page=right

Information and Playing Time

RWVR

DATA CD

VCD

You can check the playing time and remaining time of the current title, chapter, or track. Also, you can check the disc name recorded on the disc.

DISPLAY

Video

1 2 3

4 5 6

7 8 9

DVD

TIME/TEXT

Title 1

1 : English DolbyDigital 2/0Angle3(5)

A Title number/name

(Track number for CDs/VIDEO CDs without PBC, scene number for VIDEO CDs with PBC, track number/name for DATA CDs)

B Available functions for DVD VIDEOs

( angle/ audio/ subtitle, etc.)

C The current selected function or audio

setting (appears only temporarily)

D The current selected angle

Example: Dolby Digital 5.1 ch

Rear (L/R)

1 : English DolbyDigital 3/2.1

Front (L/R) + Centre

LFE (Low Frequency Effect)

◆ Display 2

Example: When playing a DVD-RW (VR mode)

Guide to Displays

Press DISPLAY repeatedly.

Each time you press the button, the display changes as follows:

Title/track information (Display 1)

Play mode/time information (Display 2)

(Display off)

The displays differ depending on the disc type or playing status.

◆ Display 1

Example: When playing a DVD VIDEO

Original

DVD- RW

Movies 0:00:45

T1SP

A Disc type*2/format (page 8) B Title type (Original or Playlist) (page 68) C Play mode D Recording mode (page 45) E Playing status bar*

F Title number (chapter number*1) (page 65)

(Track number for CDs/VIDEO CDs without PBC, scene number for VIDEO CDs with PBC, track number (album number*

) for

DATA CDs)

G CD text (album name) (when text is

recorded on a CD)

,continued

RDR-GXD500

2-188-393-11(1)

Page 36

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 36 Mardi, 7. septembre 2004 9:41 09

master page=left

H Playing time (remaining time*1)

*1Displayed when you press TIME/TEXT repeatedly. *2Displays Super VCDs as “SVCD”, DATA CDs as

“CD.”

*3Does not appear with VCDs, or DATA CDs.

z Hints

• If “DTS” is set to “Off” in Audio Setup, the DTS track selection option will not appear on the screen even if the disc contains DTS tracks (page 85).

• When “Auto Display” is set to “On” (default) in Options Setup (page 90), playback information automatically appears when the recorder is turned on, etc.

Notes

• The recorder can only display the first level of a CD’s text, such as the disc name.

• The letters or symbols that cannot be displayed are replaced with “*.”

Checking the playing/remaining time

You can view the playing or time information displayed on the TV screen and the front panel display.

Press TIME/TEXT repeatedly.

The displays differ depending on the disc type or playing status.

Example: When playing a CD

Track playing time and the current track/index number

Remaining time of the current track

Playing time of the disc

Remaining time of the disc

CD text (when available)

Notes

• The recorder can only display the first level of a CD’s text, such as the disc name.

• The letters or symbols that cannot be displayed are replaced with “*.”

• Playing time of MP3 audio tracks may not be displayed correctly.

◆Front panel display

Example: When playing a DVD

Playing time and number of the current title

Remaining time of the current title

Playing time and number of the current chapter

Remaining time of the current chapter

RDR-GXD500

2-188-393-11(1)

Page 37

D:\DVD

manual\Final\218839311_FM\01GB05HOW.fm

01GB01.book Page 37 Mardi, 7. septembre 2004 9:41 09

How to Enter Characters

You can label a title, disc, or program by entering characters. You can enter up to 64 characters for a title or disc name, but the actual number of characters displayed in the menus such as the Title List will vary. When the display for entering characters appears, follow the steps below.

master page=right

3 Repeat steps 1 and 2 to enter the

remaining characters.

Input row

Input Title Name

Kids

,. - 1

BA C 2

ED F 3

HG I 4

KJ L 5

Back

Clear All

Space

QP R S

UT V 8

XW Y Z79

NM O 6

"A" "a" Symbol

Cancel

Finish

Guide to Displays

Number buttons, SET

1 2 3

4 5 6

7 8 9

TOOLS

</M/m/,, ENTER

1 Press </M/m/, to move the cursor to

the right of the screen and select “A” (upper-case), “a” (lower-case), or “Symbol,” and press ENTER.

The characters of the selected type are displayed.

2 Press </M/m/, to select the character

you want to enter, and press ENTER.

The selected character appears at the top of the display. Example: Input Title Name

Input Title Name

,. - 1

BA C 2

ED F 3

HG I 4

KJ L 5

Back

Clear All

Space

NM O 6

QP R S

UT V 8

XW Y Z79

"A" "a" Symbol

Cancel

Finish

To erase a character, move the cursor to the right of the character at the input row. Select “Back” and press ENTER. To insert a character, move the cursor to the right of the point where you want to insert the character. Select the character and press ENTER. To erase all of the characters, select “Clear All” and press ENTER.

4 Select “Finish,” and press ENTER.

To cancel the setting, select “Cancel.”

To use the number buttons

You can also use the number buttons to enter characters.

1 In step 2 above, press a number button

repeatedly to select a character. Example: Press the number 3 button once to enter “D.” Press the number 3 button three times to enter “F.”

2 Press SET and select the next character. 3 Select “Finish” and press ENTER.

RDR-GXD500

2-188-393-11(1)

Page 38

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 38 Mardi, 7. septembre 2004 9:41 09

master page=left

Guide to Digital Services

Note

Digital Services availability depends on the broadcaster. Digital Services are not instantly available when the recorder is first turned on. Digital Services data are obtained when the recorder is in standby mode. This may take up to 30 minutes during which the standby indicator flashes to indicate that data is being obtained. When the flashing stops, press the [/1 button to exit standby mode, then proceed as follows.

EPG (Electronic Programme Guide)

The EPG provides a quick and easy way to:

• View a complete list of all available channels.

• View a channel list related to a chosen category.

• Set a programme to be recorded (page 48).

Viewing a list of available channels

Number buttons, SET

CLEAR

CURSOR MODE

O RETURN

1 2 3

4 5 6

7 8 9

Coloured control buttons

</M/m/,, ENTER

1 Press the button to display the EPG.

This display consists of an information box and a ten channel programme list covering a two hour period.

Example of EPG Display:

All Programmes

040 DDE NEWS 15

Thu 27 Oct

DDE NEWS 15 NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

Page Up Page Down Category 30 min View

10:30 11:00 11:30 12:00

DDE News

Live from Prague No Event Information No Event Information

Foreign Markets - Mor...

Opening...

Hobbies and Interests

John's...

News

EFF

Weather

Family

No Event Information City

Houses

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous... EFF

News

Tennis

A Indicates the TV or Radio mode. The Radio

mode is indicated by a Radio icon

B Indicates the Local Channel Number and

the Channel name of the programme that is currently highlighted in the list

C Indicates the currently highlighted

programme and allows you to move arround the list

D Channel name E Indicates the programme currently on view

in the background

F Programme on view in the background G Indicates if a timer recording is associated

to the event (page 48)

H Coloured Control button I Truncated programme title in case the name

is too long to be displayed in the cell

J Event bar (e.g. Indicates a timer recording

has been set during this time)

K Time slot L Icon tray. Depending on the channel and

programme settings some icons may appear in the display:

: The channel on the programme is locked

(page 78)

: Timer event icons (page 48)

M Indicates the current time and date

RDR-GXD500

2-188-393-11(1)

Page 39

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 39 Mardi, 7. septembre 2004 9:41 09

master page=right

2 Press the </M/m/, buttons or enter a

channel number using the number buttons to move around the list.

If you press the , button after highlighting the last programme on the right, the schedule for the next two hours is displayed (depending on availability from the broadcaster).

All Programmes

040 DDE NEWS 15

Thu 27 Oct

DDE NEWS 15 NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

Page Up Page Down Category 30 min View

10:30 11:00 11:30 12:00

DDE News

Live from Prague No Event Information No Event Information Opening...

Foreign Markets - Mor...

John's...

Hobbies and Interests

EFF

News

Weather

Family

No Event Information City

Houses

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous...

News

EFF

Tennis

3 Press the BLUE button to toggle the display

between the 2 hours schedule viewing (half hour time slots) and the 30 minutes schedule viewing (15 minutes time slots).

4 Press the RED button to display the

previous ten channels or the GREEN button to display the next ten channels.

5 Select a current time broadcasted

programme you wish to view. Once highlighted, press the ENTER button to obtain a preview in the background.

6 Press ENTER once more to exit the EPG

and view the programme.

Viewing channels related to a specific category.

This feature allows you to search for channels related to a particular topic. For example, if you select ‘News’ from the category pop-up list, then only channels related to News will be shown in the EPG.

Note

The category of each programme is determined by the broadcaster.

1 2 3

4 5 6

7 8 9

Coloured control buttons

O RETURN

</M/m/,, ENTER

Guide to Digital Services

z Hints

• If you press the CURSOR MODE button on the remote control when the EPG is on display, you have the option to view the programme schedule 24 hours in advance (when available).

• Press the BLUE button to view the next 24 hour schedule.

• Press the YELLOW button when you wish to return to the previous days schedule.

• The time range can be moved up to 8 days from the current time.

1 Press the button to display the EPG. 2 Press the YELLOW button. The category

pop-up list appears.

Category Sports Films Entertainment Sports Favourite List 1

Back

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous...

News

EFF

Tennis

All Programmes

040 DDE NEWS 15

Thu 27 Oct

DDE NEWS 15 NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

10:30 11:00 11:30 12:00

DDE News

DDE News Live from Prague No Event Information No Event Information Opening...

Foreign Markets - Mor... John's...

Hobbies and Interests EFF

News

Weather

Family No Event Information City

Houses

3 Press the M/m buttons to highlight the

category you want, then press the ENTER button.

,continued

RDR-GXD500

2-188-393-11(1)

Page 40

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 40 Mardi, 7. septembre 2004 9:41 09

The chosen category is displayed in a title bar at the top of the EPG display and only programmes related to that category will be shown in the list.

◆ Some examples of category types are as follows:

All Programmes: This gives a complete channel list. Favourie List 1: Displays the favourite channels you have stored in the Favourite list 1 folder (page 42). Films: Displays movies available for viewing. News: Displays all news channels. Entertainment: Displays all entertainment channels. Sports: Displays all sports channels. Kids: Displays all children’s channels. Music: Displays all music channels.

4 Press the M/m buttons to highlight the

programme you wish to view, then press the ENTER button to exit the category menu and view the selected programme.

master page=left

Programme information

The programme information display provides a quick and easy way to:

• View descriptions of the programmes being broadcast now and next on the current channel.

• View descriptions of the programmes being broadcast now and next on the other channels.

• Switch between TV and RADIO channels.

• Preview another channel in the background or change to that channel.

Displaying the programme information

Number buttons, SET

CLEAR

1 2 3

4 5 6

7 8 9

TV/RADIO

O RETURN

</M/m/,, ENTER

1 Press the button to display the

programme information screen.

The display consists of an information box showing a description of the current programme and the name of the next programme on that channel.

2 Press the M/m buttons or enter a channel

number using the number buttons to display programme information on other channels.

Press the ENTER button if you wish to obtain a preview of the chosen channel.

RDR-GXD500

2-188-393-11(1)

Page 41

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 41 Mardi, 7. septembre 2004 9:41 09

master page=right

Viewing a digital text

040 DDE NEWS 15

DDE News

10:30-11:00

News with reports from Britain an arround the world.

ENTER RETURN

Thu 27 Oct 10:32

DDE News

11:00-12:00

3 Press the TV/RADIO button to switch

between the TV and Radio channels

4 Press the </, buttons to toggle the

display between a description of the current programme and the next programme on a channel.

5 When viewing information for the currently

displayed channel, press the ENTER button to exit the information display and view the programme.

service

Many digital TV channels broadcast information via their text service. This digital service includes high quality digital text and graphics along with advanced navigation options. Additionally, this recorder has access to dedicated text channels transmitted by the broadcasters.

Note

The appearance, content and navigation methods of all digital text services are decided by the broadcaster.

Selecting digital text from dedicated digital teletext channels

Number buttons, SET

CLEAR

1 2 3

4 5 6

7 8 9

PROG +/–

Coloured control buttons

</M/m/,, ENTER

Guide to Digital Services

1 Select a dedicated channel that is

broadcasting digital text.

If you do not know the number of a dedicated digital text channel, you can use the ‘Electronic Programme Guide’ by pressing the button to find one (page 38).

2 Once the text page is displayed (this may

take some time), follow the on-screen instructions to obtain your required selection.

On some pages the TV programme may also be displayed on the text screen. On-screen instructions will inform you how to change the displayed programme.

,continued

RDR-GXD500

2-188-393-11(1)

Page 42

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 42 Mardi, 7. septembre 2004 9:41 09

3 If you are instructed to press ‘OK’ or

‘Select’ when viewing the text pages, press the ENTER button.

4 When you have finished viewing the text

service, follow the on screen instructions, or press the PROG +/- button to exit.

Selecting digital text from other channels

Digital text services may also be available on other digital channels. This is sometimes indicated by a small symbol on your TV screen, superimposed on the programme you are watching.

1 Select a channel. 2 Press the button or RED button or the

button indicated on screen by the broadcaster.

Sport 10:37 27 Oct

Main headlines Football Cricket French Open Tennis Rugby Union Golf Motor Sport More

GO TO TV SHORTCUTS BACK MENU

Press BLUE to change section

master page=left

Favourites

The Favourite application gives you the option to:

• Store your favourite channels into one of four TV or four Radio lists.

• Add or delete channels to the Favourites List.

• Quickly display a favourite channel on screen.

Setting a favourite list

Number buttons, SET

CLEAR

SYSTEM MENU

O RETURN

1 2 3

4 5 6

7 8 9

TV/RADIO

Coloured control buttons

</M/m/,, ENTER

3 Once the text information is displayed, you

can access required information by using the </M/m/, buttons, the coloured buttons and/or the numbered buttons on the remote control.

If you are instructed to press ‘OK’ or ‘Select’ when viewing the text pages, press the ENTER button on your remote control.

4 When you have finished viewing the text

service displays, follow the on screen instructions, or press the PROG +/- button to exit.

1 Press SYSTEM MENU.

The System Menu Display appears.

2 Select “SETUP,” and press ENTER.

The Setup Display appears.

3 Select “DTV Settings,” and press ENTER.

SETUP

Settings

Favourites

DTV Settings

Parental Lock

Video

Tuning

Audio

Technical information

Features

Password

Options

Easy Setup

RDR-GXD500

2-188-393-11(1)

Page 43

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 43 Mardi, 7. septembre 2004 9:41 09

master page=right

4 Select “Favourites,” and press ENTER

The DTV Settings- Favourites List 1 display appears.

Favourites List 1

Programme 001 002 003 004 005

Page Up Page Down Next List Show Fav

Service DDE News AAC NCE 5 Channel J Digital Teletext

This display shows all the TV or Radio channels available to you.

5 Press the TV/RADIO button to display

either your favourite TV or favourite Radio channels at any time.

The Radio mode is indicated by the presence of a Radio icon in the Favourites List panel.

6 Press the M/m buttons or enter a channel

number to highlight a channel you want to add as a favourite, then press the ENTER button.

Favourites List 1

Service

Programme

DDE News

001

AAC

002

NCE 5

003

Channel J

004

Digital Teletext

005

Page Up Page Down Next List Show Fav

If you do not wish to choose from one of the five channels in the display, press the RED or GREEN button to view the previous or next five channels available.

Deleting a favourite channel

A channel selected as a favourite is identified by an icon In Step 6 above press the M/m buttons to highlight the channel you want to delete from your Favourites List, then press ENTER: the icon next to the programme number disappears.

next to the programme number.

Moving to a different favourite list

1 While a Favourites List is displayed, press

repeatedly the YELLOW button on the remote control until the favourite list you want to view is displayed.

Favourites List 3

Service

Programme

DDE News

001

AAC

002

NCE 5

003

Channel J

004

Digital Teletext

005

Page Up Page Down Next List Show Fav

2 To add a channel to this new list, press the

M/m button to highlight the channel you wish to add and press the ENTER button.

3 When you have stored all your favourite

channels, press the RETURN button repeatedly to come back to normal operation.

Watching or listening to a favourite channel

Number buttons, SET

CLEAR

O RETURN

1 2 3

4 5 6

7 8 9

TV/RADIO

Coloured control buttons

</M/m/,, ENTER

1 While in normal operation mode, press

the button on the remote control.

A Favourite list display appears.

Guide to Digital Services

z Hints

• Press the BLUE button to view the list showing only your favourite channels.

• Press the BLUE button once again when you wish to return to the previous favourite channel setting display.

Favourites List 1

DDE News

003

AAC

004

NCE 5

005

Channel J

007

Digital Teletext

008

List 2Add to List 1 List 3 List 4

,continued

RDR-GXD500

2-188-393-11(1)

Page 44

D:\DVD

manual\Final\218839311_FM\01GB05DIG.fm

01GB01.book Page 44 Mardi, 7. septembre 2004 9:41 09

Each favourite list is represented by a coloured button.

2 Press the TV/RADIO button to display

either your favourite TV or favourite Radio channels at any time.

The Radio mode is indicated by the presence of a Radio icon in the Favourites List panel.

3 Press the coloured button on the remote

control that represents the desired list to be displayed.

4 Press the M/m button to highlight the

channel you wish to view or listen to, then press the ENTER button.

z Hint

If you wish, the channel on view in the background can be added to the favourite list. Simply press the coloured button indicated in the display to add it to the list.

master page=left

Index

The Index application is an easy way to display a scrollable list of all the tuned channels, including your favourites channel lists, and allows one of these to be selected.

Number buttons, SET

CLEAR

O RETURN

1 2 3

4 5 6

7 8 9

TV/RADIO

Coloured control buttons

</M/m/,, ENTER

1 While in normal operation mode, press the

ENTER button on the remote control.

The Index display appears.

Channel List

DDE News

001

AAC

002

NCE 5

003

Channel J

004

Digital Teletext

005

List 2List 1 List 3 List 4

2 Press the TV/RADIO button to display

either the TV or the Radio channels at any time.

The Radio mode is indicated by the presence of a Radio icon in the Index panel.

3 Press the coloured button on the remote

control if you wish to display your Favourites Lists.

4 Press the M/m buttons to highlight the

desired channel, then press the ENTER button to exit the index menu and view the selected channel.

RDR-GXD500

2-188-393-11(1)

Page 45

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 45 Mardi, 7. septembre 2004 9:41 09

master page=right

Recording

Before Recording

Before you start recording…

• This recorder can record on various discs. Select the disc type according to your needs (page 8).

• Check that the disc has enough available space for the recording (page 32). For DVD+RWs and DVD-RWs, you can free up disc space by erasing titles (page 69).

• Adjust the recording picture quality and picture size if necessary (page 54).

z Hint

Timer recordings will be made regardless whether or not the recorder is turned on. You can turn off the recorder without affecting the recording even after recording starts.

Notes

• If any digital teletext is operated while recording, it’s contents will be recorded on the disc.

• If the subtitles are displayed while recording, they will be recorded on the disc.

Recording mode

Like the SP or LP recording mode of VCRs, this recorder has six different recording modes. Select a recording mode according to the time and picture quality you need. For example, if picture quality is your top priority, select the High Quality mode (HQ). If recording time is your priority, Super Long Play mode (SLP) can be a possible choice. Note that the recording time in the following table is an approximate guide. Press REC MODE repeatedly to switch the recording modes.

Recording mode Recording time

HQ (High quality) 60 HSP R 90 SP (Standard mode) 120 LP r 180 EP r 240 SLP (Long duration) 360

(minute)

Note

Situations below may cause slight inaccuracies with the recording time. – Recording a programme with poor reception, or a

programme or video source of low picture quality – Recording on a disc that has already been edited – Recording only a still picture or just sound

Unrecordable pictures

Pictures with copy protection cannot be recorded on this recorder. When the recorder receives a copy guard signal, the recorder continues to record but only a blank, grey coloured screen will be recorded.

Copy control signals

Copy-Free

Copy-Once

Copy-Never None (a blank screen is

* The recorded disc can be played only on CPRM

compatible equipment.

Recordable discs

RWVR-RW

RWVR

Ver.1.1 with CPRM*

recorded)

Video

Recording

I want to record with the best possible picture quality, so I’ll select HQ.

RDR-GXD500

2-188-393-11(1)

Page 46

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 46 Mardi, 7. septembre 2004 9:41 09

Timer Recording (Standard/ EPG)

master page=left

RWVR

Video

You can set the timer for a total of thirty programmes. There are two methods to set the timer: the standard method and the EPG method.

• Standard: Set the date, time, and programme position of the programme manually. This method allows you to set the timer up to one month in advance.

• EPG: Set a programme to be recorded based on the information provided by the EPG (Electronic Programme Guide) (page 48). This method allows you to set the timer up to 8 days from the current time (depending on programme availability from the broadcaster).

Setting the timer manually (Standard)

1 2 3

4 5 6

7 8 9

TOOLS

</M/m/,, ENTER

x REC STOP

[TIMER]

1 Press Z (open/close), and place a

recordable disc on the disc tray.

With the recording side facing down

2 Press Z (open/close) to close the disc

tray.

Wait until “LOAD” disappears from the front panel display. Unused DVDs are formatted automatically.

3 Press [TIMER].

”

Timer - Standard

Set the timer manually.

Date

Start Source Prog. ModeStop

Tod a y

Cancel

4 Select an item using </, and adjust

using M/m.

“Date”: Sets the date. The item changes as follows: Today y Tomorrow y …… y Thu

28.10 (1 month later) y Sun (every Sunday) y …… y Sat (every Saturday) y Mon-Fri (Monday to Friday) y Mon-Sat (Monday to Saturday) y Sun-Sat (Sunday to Saturday) y Today

“Start”: Sets the start time. “Stop”: Sets the stop time. “Source”: Selects the input source as follows: TV y Radio y Line (External input) y TV “Prog.”: Selects the TV/Radio programme position or input line. “Mode”: Selects the recording mode (page 45).

• If you make a mistake, select the item and change the setting.

5 Select “OK,” and press ENTER.

The Timer List menu (page 51) appears. The TIMER REC indicator lights up on the front panel and the recorder is ready to start recording. Unlike a VCR, there is no need to turn off the recorder before the timer recording starts.

RDR-GXD500

2-188-393-11(1)

Page 47

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 47 Mardi, 7. septembre 2004 9:41 09

master page=right

To stop recording during timer recording

Open the remote’s cover and press x REC STOP. Note that it may take a few seconds for the recorder to stop recording.

Rec Mode Adjust

If there is not enough available disc space for the recording, the recorder automatically adjusts the recording mode to enable the entire programme to be recorded. This function is normally set to “On.”

To cancel this function, press TOOLS while the Timer List is displayed. Select “Rec Mode Adjust” and press ENTER. Select “Off” and press ENTER.

If the timer settings overlap

Overlapped timer settings are shown as follows.

Timer

These timer settings overlap. Do you want to continue?

Fri 29.10 21:00-22:00 AAB SP

Fri 29.10 21:30-22:30 DEF SP

OK Cancel

To store the setting as shown, select “OK.” The programme that starts first has priority and the second programme starts recording only after the first programme has finished (page 52). To cancel the overlapped timer setting, select “Cancel.”

One Touch Timer

If you use the SMARTLINK connection, you can easily display the timer programming menu. When the TV is turned on or in standby mode, insert a disc and press [TIMER]. The recorder automatically turns on and the TV’s input is switched to the recorder. The Timer programming menu appears.

z Hint

You can play the recorded programme by selecting the programme title in the Title List menu.

Notes

• If “The disc is full or nearly full” appears on the screen, change the disc, or make available space for the recording (DVD+RW/DVD-RW only) (page 70).

• Check that the clock is correctly set before setting the timer recording. If not, the timer recording cannot be made.

• Even if the timer is set for the same daily or weekly programme, the timer recording cannot be made if it overlaps with a programme th at has priority. “ ” will appear next to the overlapped setting in the Timer List. Check the priority order of the settings (page 51).

• Even if the timer is set, timer recordings cannot be made while recording a programme that has priority.

Recording

To confirm, change, or cancel timer recording

See “Checking/Changing/Cancelling Timer Settings (Timer List)” (page 51).

To extend the recording duration time while recording

1 Press TOOLS during recording.

The TOOLS menu appears.

2 Select “Extend Rec” and press ENTER.

Extend Rec. Time

Set the timer extend function.

Tue 28.9 10:00-11:30 AAB SP

Extend Time

Off

Cancel

3 Press M/m to select the duration time.

You can set the duration in increments of 10 minutes, for a maximum of 60 minutes.

4 Select “OK” and press ENTER.

,continued

RDR-GXD500

2-188-393-11(1)

Page 48

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 48 Mardi, 7. septembre 2004 9:41 09

master page=left

Recording TV programmes using the EPG application

The EPG application is a feature that simplifies setting the timer. Just select the programme you wish to record in the EPG display. The date, time, and channel of that programme are set automatically.

Number buttons, SET

CLEAR

O RETURN

1 2 3

4 5 6

7 8 9

Coloured control buttons

</M/m/,, ENTER

x REC STOP

1 Insert a recordable disc. 2 Press the button to display the EPG. 3 Press the </M/m/, buttons or enter a

channel number using the number buttons to move around the list.

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous...

News

EFF

Tennis

All Programmes

040 DDE NEWS 15

Thu 27 Oct

10:30 11:00 11:30 12:00

DDE NEWS 15

DDE News

NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

Page Up Page Down Category 30 min View

DDE News

Live from Prague No Event Information No Event Information Opening...

Foreign Markets - Mor...

John's...

Hobbies and Interests

EFF

News

Weather

Family

No Event Information City

Houses

To know more about the navigation options in the EPG application, see page 38.

4 Select a future programme you wish to

record. Once highlighted, press the ENTER button.

The sub menu appears with the description of the programme displayed in the information box.

Event Action

Select an action for this event

Hobbies and Interests Thu 27.10 11:00-12:00 NCE 1 SP

Today's Hint: How to make finger puppets.

Timer

Modify

Erase

Check Overlap

Cancel

In case is displayed: Indicates that the programme is age limited (page 78).

5 Select “Timer,” and press ENTER.

The Timer setting confirmation display appears

Timer

Do you want to record this event?

Hobbies and Interests Thu 27.10 11:00-12:00 NCE 1 SP

OK Cancel Modify

6 Select “OK,” and press ENTER.

All Programmes

040 DDE NEWS 15

Thu 27 Oct

DDE NEWS 15 NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

Page Up Page Down Category 30 min View

10:30 11:00 11:30 12:00

DDE News

Live from Prague No Event Information No Event Information Opening...

Foreign Markets - Mor...

John's...

Hobbies and Interests

EFF

News

Weather

Family

No Event Information City

Houses

An event bar and a new icon appears in the EPG display indicating that a timer event is associated to that programme. Your recorder will automatically begin recording when the programme starts.

◆ Some examples of timer event icon types are as follows:

(red): Indicates the programme is set as

timer and whole programme can be recorded.

(grey): Indicates the programme is set as timer but only a part of the programme can be recorded. (e.g. because of timer setting overlap).

(red): Indicates the programme is now recording.

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous...

News

EFF

Tennis

RDR-GXD500

2-188-393-11(1)

Page 49

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 49 Mardi, 7. septembre 2004 9:41 09

master page=right

To stop recording during timer recording

Open the remote’s cover and press x REC STOP. Note that it may take a few seconds for the recorder to stop recording.

If the timer settings overlap

See page 47.

To confirm, change, or cancel timer recording

See “Checking/Changing/Cancelling Timer Settings (EPG)” (page 49).

z Hint

The Rec Mode Adjust function also works with this timer method (page 47).

Note

It is not possible to extend the recording duration time of the timer recording set using the EPG application timer setting.

Checking/Changing/ Cancelling Timer Settings (EPG)

RWVR-RW

Video

You can check, change, or cancel timer settings using the EPG menu.

Number buttons, SET

CLEAR

O RETURN

1 2 3

4 5 6

7 8 9

Coloured control buttons

</M/m/,, ENTER

Recording

1 Press the button to display the EPG.

A timer setting can be identified thanks to the event bar and the timer event icon displayed in the EPG screen. For details see page 48.

All Programmes

040 DDE NEWS 15

Thu 27 Oct

DDE NEWS 15 NCE J9 CMY AAC NCE 1 EFF News Channel J HGF NCE 5

Page Up Page Down Category 30 min View

10:30 11:00 11:30 12:00

DDE News

Live from Prague No Event Information No Event Information Opening...

Foreign Markets - Mor...

John's...

Hobbies and Interests

EFF

News

Weather

Family

No Event Information City

Houses

Thu 27 Oct 10:32

NCE News

Drive in ...

No Event...

DDE News

No Event... Fabulous...

News

EFF

Tennis

2 Press the </M/m/, buttons to select the

timer event you want to check/change/ cancel. Once highlighted, press the ENTER button.

,continued

RDR-GXD500

2-188-393-11(1)

Page 50

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 50 Mardi, 7. septembre 2004 9:41 09

master page=left

The Event Action menu appears.

Event Action

Select an action for this event.

Hobbies and Interests Thu 27.10 11:00-12:00 NCE 1 SP 1.1GB

Today's Hint: How to make finger puppets.

Timer

Modify

Erase

Check Overlap

Cancel

3 Press the M/m buttons to select the

options. Once highlighted, press the ENTER button.

The sub menu appears:

“Modify”: Changes the timer setting. Select an item using </, and adjust using M/m. Select “OK” and press ENTER.

Modify

Modify the timer setting.

Hobbies and Interests Thu 27.10 11:00-12:00 NCE 1

Record everyMode

SP Off

Note

If you set “Record every” to an other option than “Off”, then your EPG timer recording will be converted into a standard timer recording: the timer event icon disappears from the EPG display.

Cancel

Select “Close” to return to the EPG screen.

To change or cancel the setting, repeat steps 2 and 3 above.

“Erase”: Erases the timer setting. Select “OK” and press ENTER.

Erase

Are you sure you want to erase this timer setting?

Hobbies and Interests Thu 27.10 11:00-12:00 NCE 1 SP

OK Cancel

“Check Overlap”: Checks for overlapped settings.

Check Overlap

These timer settings overlap.

Thu 27.10 11:00-12:00 NCE 1

Thu 27.10 11:30-14:00 DDE

RDR-GXD500

2-188-393-11(1)

Page 51

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 51 Mardi, 7. septembre 2004 9:41 09

Checking/Changing/ Cancelling Timer Settings (Timer List)

RWVR-RW

Video

You can check, change, or cancel timer settings using the Timer List menu.

1 2 3

4 5 6

7 8 9

SYSTEM MENU

O RETURN

</M/m/,, ENTER

ZOOM +/–

master page=right

3 Select the timer setting you want to check/

change/cancel, and press ENTER.

The sub-menu appears.

4 Select one of the options, and press

ENTER.

“Modify”: Changes the timer setting. Select an item using </, and adjust using M/m. Select “OK” and press ENTER.

Modify

Modify the timer setting.

Date

Start Source Prog. ModeStop

::00 17 00 TV GHI SLP

Sat 30.10 16

“Erase”: Erases the timer setting. Select “OK” and press ENTER.

Erase

Are you sure you want to erase this timer setting?

DEF Sat 30.10 16:00-17:00 GHI SLP

OK Cancel

Cancel

Recording

1 Press SYSTEM MENU.

The System Menu appears.

2 Select “TIMER LIST,” and press ENTER.

To show the list in greater detail (zoom), press ZOOM+ :

TIMER LIST

Mon-Sat 22:00-22:15 DDE News

Tennis Fri 29.10 20:30-21:30 EEF

AAB Fri 29.10 21:00-22:00 DDE

DEF Sat 30.10 16:00-17:00 GHI

Timer information displays the recording date, time, recording mode, etc.

: Indicates that the setting is overlapped by

another setting.

(green): Indicates the setting can be

recorded

(red): Indicates the setting currently being

recorded.

(grey): Indicates that the setting cannot be

recorded in the selected recording mode.

10:30

SLP

“Check Overlap”: Checks for overlapped settings. Select “Close”and press ENTER to return to the Timer List.

Check Overlap

These timer settings overlap.

Fri 29.10 21:00-22:00 AAB

Fri 29.10 21:30-22:30 DEF

“Info”: Displays the timer setting information box along with the disc space required to record the whole programme (according to the selected recording mode).

Information

Fri 2 9.10 21:30-22:30 DEF LP 1.4GB

News with reports from Europe an arround the world.

Press O RETURN to come back to the Timer List.

To change or cancel the setting, repeat steps 3 and 4 above.

,continued

RDR-GXD500

2-188-393-11(1)

Page 52

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 52 Mardi, 7. septembre 2004 9:41 09

When the timer settings overlap

The programme that starts first has priority and the second programme starts recording only after the first programme has finished.

7:00 8:00 9:00 10:00

master page=left

Recording Without the Timer

RWVR

Video

will be cut off

◆When the recordings start at the same time

The programme that is set last has priority. In this example, timer setting B is set after A, so the first part of timer setting A will not be recorded.

7:00 8:00

9:00 10:00

◆When the end time of one recording and the start time of another are the same

After finishing the previous recording, the other recording may be delayed.

7:00 8:00 9:00 10:00

To turn off the Timer List

Press O RETURN.

z Hint

While recording, you cannot modify the timer setting for the current recording, but you can extend the recording duration of the recording time (page 47).

Notes

Even if the timer is set, timer recordings cannot be made while recording a programme that has priority.

• Even if the timer is set for the same daily or weekly programme, the timer recording cannot be made if it overlaps with a programme that has priority. “ ” will appear next to the overlapped setting in the Timer List. Check the priority order of the settings.

1 2 3

4 5 6

7 8 9

z REC

REC MODE

Insert a recordable disc.

PROG +/–

t (TV/video), TV/DVD

</M/m/,, ENTER

X REC PAUSE

x REC STOP

2 Press PROG +/– to select the programme

position or input source you want to record.

3 Press REC MODE repeatedly to select the

recording mode.

Each time you press the button, the display changes on the TV screen as follows:

HQ SP LP EPHSP SLP

For more details about the recording mode, see page 45.

4 Press z REC.

Recording starts. Recording continues until you stop the recording or the disc is full.

RDR-GXD500

2-188-393-11(1)

Page 53

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 53 Mardi, 7. septembre 2004 9:41 09

master page=right

To stop recording

Press x REC STOP located beneath the remote control cover. Note that it may take a few seconds for recording to stop.

To pause recording

Press X REC PAUSE located beneath the remote control cover. To restart recording, press the button again.

To watch another TV programme while recording

If your TV is connected to the LINE 1-TV jack, set your TV to the TV input using the TV/DVD button and select the programme you want to watch. If your TV is connected to the LINE 2 OUT or COMPONENT VIDEO OUT jacks, set the TV to TV input using the

t (TV/video) button

(page 20).

TV Direct Rec

If you use the SMARTLINK connection, you can easily record what you are watching on your TV. When the TV is turned on or in standby mode, insert a disc and press z REC. The recorder automatically turns on and starts recording what you are watching on the TV. “TV” appears in the front panel display. You cannot turn off the TV or change the programme position during TV Direct Rec. To turn off the function, set “TV Direct Rec” to “Off” in Features Setup (page 86).

Using the Quick Timer function

You can set the recorder to record in 30-minute increments.

Press z REC repeatedly to set the duration.

Each press advances the time in 30-minute increments. The maximum duration is six hours.

0:30 1:00 5:30 6:00

The time counter decreases minute by minute to 0:00, then the recorder stops recording (power does not turn off). Even if you turn off the recorder during recording, the recorder continues to record until the time counter runs out. Note that the Quick Timer function does not work if “TV Direct Rec” is set to “On” in Features Setup (page 86).

To cancel the Quick Timer

Press z REC repeatedly until the counter appears in the front panel display. The recorder returns to normal recording mode.

(normal recording)

Recording

z Hint

If you do not want to watch TV while recording, you can turn off the TV. When using a decoder, make sure to leave it on.

Notes

• After pressing z REC, it may take a short while to start

recording.

• You cannot change the recording mode while recording or during recording pause.

• If there is a power failure, the programme you are recording may be erased.

• To use the TV Direct Rec function, you must first set the recorder’s clock correctly.

,continued

RDR-GXD500

2-188-393-11(1)

Page 54

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 54 Mardi, 7. septembre 2004 9:41 09

master page=left

Adjusting the recording picture quality and size

You can adjust the recording picture quality and picture size.

1 2 3

4 5 6

7 8 9

TOOLS

</M/m/,, ENTER

DISPLAY

1 Before recording starts, press TOOLS and

select “Rec Settings.” Then press ENTER.

Rec. Settings

Select the item you want to change.

Rec Mode :

Line Rec. Picture Size :

Rec NR :

Rec Video Equalizer

4 : 3

Off

2 Select the item you want to adjust, and

press ENTER.

The adjustment display appears.

Example: Rec NR

Rec NR

Off 1 2 3

“Rec Mode”: Selects the recording mode for the desired recording time and picture quality. For more information, see “Recording mode” (page 45).

“Line Rec. Picture Size”: Sets the picture size of the Line input to be recorded.

• 4:3 (default): Sets the picture size to 4:3.

• 16:9: Sets the picture size to 16:9 (wide mode).

This function works with DVD-Rs and DVDRWs (Video mode) when the recording mode is set to HQ, HSP, or SP. For all other recording modes, the screen size is fixed at “4:3.” For DVD-RWs (VR mode), the actual picture size is recorded regardless of the setting. For example, if a 16:9 size picture is received, the disc records the picture as 16:9 even if “DVD Rec. Picture Size” is set to “4:3.” For DVD+RWs/DVD+Rs, the screen size is fixed at “4:3.”

“Rec NR” (noise reduction): Reduces noise contained in the video signal.

“Rec Video Equalizer”: Adjusts the picture in greater detail. Press M/m to select the item you want to adjust, then press ENTER.

• Contrast: Changes the contrast.

• Brightness: Changes the overall brightness.

• Colour: Makes the colours deeper or lighter.

3 Adjust the setting using </M/m/,,

and press ENTER.

The default setting is underlined. “Rec NR”: (weak) Off “Rec Video Equalizer”:

• Contrast: (weak) –3 ~ 0

• Brightness: (dark) –3 ~ 0

• Colour: (light) –3 ~ 0

Repeat steps 2 and 3 to adjust any other items.

Notes

• If one programme contains two picture sizes, the selected size is recorded. However, if the 16:9 signal cannot be recorded as 16:9, it is recorded as 4:3.

• When playing a 16:9 size picture recorded as 4:3, the image is fixed to 4:3 letter box regardless of the setting in “TV Type” of Video Setup (page 82).

• Remnants of images may appear on your screen when using “Rec NR.”

1 ~ 3 (strong)

~ 3 (strong)

~ 3 (bright)

~ 3 (deep)

RDR-GXD500

2-188-393-11(1)

Page 55

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 55 Mardi, 7. septembre 2004 9:41 09

master page=right

Checking the disc status while recording

You can check the recording information such as recording time or disc type.

Press DISPLAY twice during recording.

The recording information appears.

DVD-RW

VIDEO

1:23:45SP

A Disc type/format B Recording status C Recording mode D Recording time

Press DISPLAY to turn off the display.

Creating chapters in a title

The recorder will automatically divide a recording (a title) into chapters by inserting chapter marks at 6 or 15-minute intervals during recording. Select the interval, “6Min” (default) or “15Min” in “Auto Chapter” of Features Setup (page 86).

Recording From Connected Equipment With a Timer (Synchro Rec)

You can set the recorder to automatically record programmes from connected equipment that has a timer function (such as a satellite tuner). Connect the equipment to the LINE 3 jack of the recorder (page 28). When the connected equipment turns on, the recorder starts recording a programme from the LINE 3 jack.

RWVR

Video

1 2 3

4 5 6

7 8 9

TOOLS

</M/m/,, ENTER

Recording

z Hint

You can create chapters manually when playing DVDRWs (VR mode). For details, see page 72.

x REC STOP

REC MODE

SYNCHRO REC

1 Insert a recordable disc. 2 Press INPUT SELECT repeatedly to select

“L3.”

3 Select the line input audio when recording

a bilingual programme.

Press TOOLS to display the TOOLS menu. Select “Line Audio Input” and press ENTER. Select “Bilingual” and press ENTER.

4 Press REC MODE repeatedly to select the

recording mode, HQ, HSP, SP, LP, EP, or SLP.

,continued

RDR-GXD500

2-188-393-11(1)

Page 56

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 56 Mardi, 7. septembre 2004 9:41 09

master page=left

5 Set the timer on the connected equipment

to the time of the programme you want to record, and turn it off.

6 Press SYNCHRO REC.

The SYNCHRO REC indicator lights up on the front panel. The recorder is ready to start Synchro-Recording. The recorder automatically starts recording when it receives an input signal from the connected equipment. The recorder stops recording when the connected equipment turns off.

To stop recording

Press x REC STOP or SYNCHRO REC.

To cancel Synchro Rec

Press SYNCHRO REC. The SYNCHRO REC indicator on the recorder turns off.

Notes

• The recorder starts recording only after detecting the video signal from the connected equipment. The beginning of the programme may not be recorded regardless of whether or not the recorder’s power is on or off.

• During Synchro-Recording, other operations such as normal recording cannot be done.

• To use the connected equipment while the recorder is standing by for Synchro-Recording, cancel SynchroRecording by pressing SYNCHRO REC. Be sure to turn off the connected equipment and press SYNCHRO REC to reset Synchro-Recording before the timer recording starts.

• The Synchro Rec function does not work with some tuners. For details, see the tuner’s operating instructions.

• While the recorder is standing by for SynchroRecording, the Auto Clock Set function (page 77) does not work.

7:00 8:00 9:00 10:00

First programme

Second programme

will be cut off

If the timer settings of a Synchro-Recording and another timer recording overlap

Regardless of whether or not the programme is a Synchro Rec programme, the programme that starts first has priority and the second programme starts recording only after the first programme has finished.

RDR-GXD500

2-188-393-11(1)

Page 57

D:\DVD

manual\Final\218839311_FM\01GB06REC.fm

01GB01.book Page 57 Mardi, 7. septembre 2004 9:41 09

Recording From Connected Equipment Without a Timer

You can record from a connected VCR or similar device. To connect a VCR or similar device, see “Connecting a VCR or Similar Device” (page 26).

RWVR

Video

1 2 3

4 5 6

7 8 9

TOOLS

M/m, ENTER

master page=right

4 Press TOOLS and select “Line Audio

Input.” Then press ENTER.

“Bilingual”: Records the two different sound tracks on DVD-RWs (VR mode). You can select either sound track when playing back the disc. “Stereo” (default): Records stereo sound only. Select this for discs other than DVD-RWs (VR mode).

5 Press X REC PAUSE to set this recorder to

record pause.

6 Insert the source tape into the connected

equipment and set to playback pause.

7 At the same time, press X REC PAUSE on

this recorder and the pause or play button on the connected equipment.

Recording starts. To stop recording, press x REC STOP on this recorder.

Recording

X REC PAUSE

x REC

REC MODE

INPUT SELECT

STOP

1 Insert a recordable disc. 2 Press INPUT SELECT to select an input

source according to the connection you made.

The front panel display changes as follows:

programme position

L2L1 L4L3

3 Press REC MODE repeatedly to select the

recording mode.

The recording mode changes as follows:

HQ SP LP EPHSP SLP

z Hint

You can adjust the settings for the recording picture before recording. See “Adjusting the recording picture quality and size” (page 54).

Notes

• When recording a video game image, the screen may not be clear.

• Any programme that contains a Copy-Never copy guard signal cannot be recorded. The recorder continues to record, but a blank screen will be recorded.

RDR-GXD500

2-188-393-11(1)

Page 58

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 58 Mardi, 7. septembre 2004 9:41 09

Playback

master page=left

3 Press TITLE LIST.

For details about the Title List, see “Using the Title List” (page 30).

Playing

RWVR-RW

VCD

O RETURN

Number buttons, SET

TITLE LIST

TOP MENU

m/M

DATA CD

Video

1 2 3

4 5 6

7 8 9

DVD

"/1

TOOLS

</M/m/,, ENTER

x X

1 Press Z (open/close), and place a disc on

the disc tray.

With the playback side facing down

2 Press Z (open/close) to close the disc

tray.

If you inserted a DVD VIDEO, VIDEO CD, CD, or DATA CD, press H. Playback starts.

Example: DVD-RW (VR mode)

My Movies

Sort

Date Title Number

TITLE LIST

ORIGINAL

1 AAB 13:00-14:00

2 DEF 20:00-21:00

3 AAB 9:00- 9:30

4 GHI 20:00-20:30

5 DEF 20:00-20:30

6 L3 21:00-21:30

7 L3 21:00-21:30

8 GHI 10:00-10:30

Wed

Fri

Sat

Fri

Tue

Thu

1.5/4.7GB

15. 9

17. 9

25. 9

15.10

19.10

26.10

28.10

4 Select the title, and press ENTER.

The sub-menu appears.

5 Select “Play,” and press ENTER.

Playback starts from the selected title on the disc.

To use the DVD’s Menu

When you play a DVD VIDEO, or a finalized DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R, you can display the disc’s menu by pressing TOP MENU or MENU.

To play VIDEO CDs with PBC functions

PBC (Playback Control) allows you to play VIDEO CDs interactively using the menu on your TV screen. When you start playing a VIDEO CD with PBC functions, the menu appears. Select an item using the number buttons and press ENTER. Then, follow the instructions in the menu (press

H when “Press SELECT” appears).

The PBC function of Super VCDs does not work with this recorder. Super VCDs are played in continuous play mode only.

To stop playback

Press x.

To resume playback from the point where you stopped the disc (Resume Play)

When you press H again after you stop the disc, the recorder resumes playback from the point where you pressed

To start from the beginning, press TOOLS, select “Play Beginning” and press ENTER. Playback starts from the beginning of the title/track/scene.

RDR-GXD500

2-188-393-11(1)

Page 59

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 59 Mardi, 7. septembre 2004 9:41 09

master page=right

The point where you stopped playing is cleared when: – you open the disc tray. – you play another title. – you switch the Title List menu to Original or

Playlist (DVD-RW in VR mode only). – you edit the title after stopping playback. – you change the settings on the recorder. – you turn off the recorder (VIDEO CD/CD/

DATA CD only). – you make a recording (except for DVD-RWs in

VR mode).

To play restricted DVDs (Parental Control)

If you play a restricted DVD, the message “Do you want temporarily change parental control to *?” appears on your TV screen.

1 Select “OK” and press ENTER.

The display for entering your password appears.

2 Enter your four-digit password using the

number buttons.

3 Press ENTER to select “OK.”

The recorder starts playback.

To register or change the password, see “Parental Control (DVD VIDEO only)” (page 87).

One Touch Menu

If you use the SMARTLINK connection, you can easily display the Title List. When the TV is turned on or in standby mode, insert a disc and press TITLE LIST. The recorder automatically turns on and the TV’s input is switched to the recorder. The Title List menu appears.

z Hints

• You can also use the H button in step 4 (page 58) to

start playback.

• Even if a timer recording starts during playback, neither the recording nor playback will stop (page 64).

• Even if you select “Factory Setup” in Options Setup (page 90), the Child Lock remains set.

Playback

To lock the disc tray (Child Lock)

You can lock the disc tray to prevent children from ejecting the disc. When the recorder is in standby mode, press O RETURN, ENTER, and then {/1 on the remote. “LOCKED” appears in the front panel display. The Z (open/close) button does not work while the Child Lock is set.

To unlock the disc tray, press O RETURN, ENTER, and then {/1 on the remote again when the recorder is in standby mode.

One Touch Play

If you use the SMARTLINK connection, you can easily start playing. When the TV is turned on or in standby mode, insert a disc and press H. The recorder automatically turns on and the TV’s input is switched to the recorder. Playback starts automatically.

,continued

RDR-GXD500

2-188-393-11(1)

Page 60

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 60 Mardi, 7. septembre 2004 9:41 09

Playback options

./>

master page=left

1 2 3

4 5 6

7 8 9

m / M

SUR

Buttons Operations Discs

Z (open/close) Stops play and opens the disc tray. All discs

(audio) Selects one of the audio tracks recorded on the disc

when pressed repeatedly.

: Selects the language.

DVD

RWVR

: Selects the main or sub sound.

VCD

DATA CD

: Selects stereo or monaural

RWVR

audio tracks.

(subtitle) Selects a subtitle language when pressed repeatedly.

DVD

(angle) Selects an angle when pressed repeatedly.

If various angles (multi-angles) for a scene are recorded on the disc, “ ” appears in the front panel

DVD

display.

DVD

DATA CD

VCD

RDR-GXD500

2-188-393-11(1)

Page 61

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 61 Mardi, 7. septembre 2004 9:41 09

Buttons Operations Discs

master page=right

SUR (surround) Selects one of the TVS effects when pressed

repeatedly. TVS* (TV Virtual Surround) lets you enjoy virtual surround sound effects created from the front left and right speakers. The selected setting is displayed in the front panel display for a few seconds. “TVS OFF”: No surround effect “TVS DYNAMIC”: Creates one set of virtual rear speakers. “TVS WIDE”: Creates five sets of virtual rear speakers. “TVS NIGHT”: Creates five sets of virtual rear speakers. Effective at low volume. “TVS STANDARD”: Creates three sets of virtual rear speakers. Effective when you use two separate front speakers.

/ (instant

Replays the scene/briefly fast forwards the scene. replay/instant advance)

. (previous)/ > (next)

(fast reverse/fast forward)

Goes to the beginning of the previous/next title/

chapter/scene/track.

Fast reverses/fast forwards the disc when pressed

during playback.

Search speed changes as follows:

fast reverse fast forward

FR1 T t FF1

FR2 T T t t FF2

FR3* T T T t t t FF3*

DVD

* TVS was developed

by Sony to produce home surround sound with just a stereo TV. This works with multichannel Dolby Digital and MPEG soundtracks.

RWVR

DVD

All discs

* FR3 and FF3 are only

available for DVDs.

Playback

Video

When you press and hold the button, fast forward/fast

reverse continues at the selected speed until you

release the button.

(slow, freeze frame)

Plays in slow motion when pressed for more than one

second in pause mode.

Plays one frame at a time when pressed briefly in

pause mode.

VCD

* Playback direction

only

X (pause) Pauses playback. All discs

To resume normal playback, press H.

RWVR

Video

DVD

,continued

RDR-GXD500

2-188-393-11(1)

Page 62

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 62 Mardi, 7. septembre 2004 9:41 09

master page=left

Notes

• To enjoy the TVS function, set “Digital Output” to “On” and “Dolby Digital” to “D-PCM” in Audio Setup.

• When the playback signal does not contain a signal for the rear speakers, the surround effects will be difficult to hear.

• When you select one of the surround modes, turn off the surround settings of the connected TV or amplifier (receiver).

• Make sure that your listening position is between and at an equal distance from your speakers, and that the speakers are located in similar surroundings.

• The TVS function cannot be used with discs recorded on this recorder. Angles and subtitles also cannot be changed.

• When you use the DIGITAL OUT (COAXIAL) jack to listen to MPEG audio signals and set “MPEG” to “MPEG” in Audio Setup, no sound will come from your speakers if you select one of the TVS modes.

Notes on playing DTS sound tracks on a CD

• When playing DTS-encoded CDs, excessive noise will be heard from the analogue stereo jacks. To avoid possible damage to the audio system, the consumer should take proper precautions when the analogue stereo jacks of the recorder are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1-channel decoder system must be connected to the digital jack of the recorder.

• Set the sound to “Stereo” using the (audio) button when you play DTS sound tracks on a CD (page 60).

Notes on playing DVDs with a DTS sound track

DTS audio signals are output only through the DIGITAL OUT (COAXIAL or OPTICAL) jack. When you play a DVD with DTS sound tracks, set “DTS” to “On” in Audio Setup (page 85).

Adjusting the picture quality

VCD

RWVR-RW

Video

1 Press TOOLS during playback.

The TOOLS menu appears.

2 Select “Video Settings,” and press

ENTER.

Video Settings

Select the item you want to change.

Y NR :

C NR :

BNR :

DVE :

PB Video Equalizer

Off

3 Select an item, and press ENTER.

The adjustment display appears. “Y NR” (luminance noise reduction): Reduces noise contained in the luminance element of the video signal. “C NR” (chroma noise reduction): Reduces noise contained in the colour element of the video signal. “BNR” (block noise reduction): Reduces “block noise” or mosaic like patterns in the picture. “DVE” (digital video enhancer): Sharpens the outlines of the images. “PB Video Equalizer” (Playback video equalizer): Adjusts the picture in greater detail. Select an item and press ENTER.

• Contrast: changes the contrast.

• Brightness: changes the overall brightness.

• Colour: makes the colours deeper or lighter.

• Hue: changes the colour balance.

DVD

RDR-GXD500

2-188-393-11(1)

Page 63

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 63 Mardi, 7. septembre 2004 9:41 09

master page=right

4 Press </, to adjust the setting, and

press ENTER.

The default settings are underlined.

“Y NR”: (weak) Off 1 2 3 (strong) “C NR”: (weak) Off 1 2 3 (strong) “BNR”: (weak) Off 1 2 3 (strong) “DVE”*: (weak) Off 1 2 3 (strong) “PB Video Equalizer”:

• Contrast: (weak) –3 ~ 0 ~ 3 (strong)

• Brightness: (dark) –3 ~ 0

• Colour: (light) –3 ~ 0

• Hue: (red) –3 ~ 0 Repeat steps 3 and 4 to adjust any other items.

* “1” softens the outlines of the images. “2”

enhances the outlines and “ 3” enhances them more than “2.”

Notes

• If the outlines of the images on your screen become blurred, set “BNR” to “Off.”

• Depending on the disc or the scene being played, the above BNR, Y NR, or C NR effects may be hard to discern. And, these functions may not work with some screen sizes.

• When playing a disc recorded in SLP recording mode, the BNR setting may have little effect.

• When using the DVE function, noise found in the disc may become more apparent. In this case, it is recommended that you use the BNR function with the DVE function. If the condition still does not improve, set the DVE level to “1” or “Off.”

~ 3 (bright)

~ 3 (deep)

~ 3 (green)

Adjusting the sound quality

VCD

RWVR-RW

Video

DVD

1 Press TOOLS during playback.

The TOOLS menu appears.

2 Select “Audio Settings,” and press

ENTER.

3 Select an item, and press ENTER.

“Surround (TVS)” (DVD VIDEO only): Selects one of the surround modes. For more information, see “Playback options” (page 60).

“Audio Filter” (all discs): Selects the digital filter to reduce noise above 22.05 kHz (Fs* is

44.1 kHz), 24 kHz (Fs is 48 kHz), or 48 kHz (Fs is above 96 kHz).

• Sharp (default): Provides a wide frequency range and spatial feeling.

• Slow: Provides smooth and warm sound.

* Sampling frequency of audio source. This

function only adjusts the output signals from the LINE 1 - TV, LINE 3, or LINE 2 OUT (AUDIO L/R).

4 Press </M/m/, to select the option,

and press ENTER.

Playback

Note

There may be little effect by changing the Audio Filter depending on the disc or playback environment.

RDR-GXD500

2-188-393-11(1)

Page 64

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 64 Mardi, 7. septembre 2004 9:41 09

Chasing Playback/ Simultaneous Rec and Play

RWVR

“Chasing playback” allows you to view the beginning of a programme while it is being recorded. “Simultaneous Rec and Play” allows you to view a previously recorded programme while recording another on the same disc.

1 2 3

4 5 6

7 8 9

TITLE LIST

TOOLS

M/m, ENTER

Playing from the beginning of the programme you are recording

You can view the recorded part of a programme while the recording is being made. You do not need to wait until the recording finishes.

1 Press TOOLS while recording.

The TOOLS menu appears.

2 Select “Chasing Playback,” and press

ENTER.

Playback starts from the beginning of the programme you are recording. When you fast forward to the point that you are recording, Chasing Playback returns to normal playback.

master page=left

• The picture on your TV screen freezes for a few seconds when you fast forward/fast reverse or instant replay/advance the recording.

Playing a previous recording while making another

You can play a previously recorded programme while recording another on the same disc. Playback continues even if the recording is a timer recording.

1 While recording, press TITLE LIST.

The Title List menu appears.

2 Select the title you want to play, and press

ENTER.

The sub-menu appears.

3 Select “Play,” and press ENTER.

Playback starts from the selected title.

Notes

• This function does not work when recording: – on a 1x-speed DVD-RW. – in the HQ or HSP recording mode.

• The picture on your TV screen freezes for a few seconds when you fast-forward/fast-reverse or instant replay/advance the recording.

• When playing a title recorded in the HQ or HSP recording mode, picture noise may appear depending upon the condition of the recording.

Notes

• This function does not work when recording: – on a 1x-speed DVD-RW. – in the HQ or HSP recording mode.

RDR-GXD500

2-188-393-11(1)

Page 65

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 65 Mardi, 7. septembre 2004 9:41 09

Searching for a Title/ Chapter/Track, etc.

VCD

RWVR-RW

Video

DATA CD

You can search a DVD by title or chapter, and VIDEO CD/CD/DATA-CD by track or scene. As titles and tracks are assigned individual numbers on the disc, select the title or track by entering its number. You can also search for a scene using the time code.

DVD

master page=right

3 Press the number buttons to select the

number of the title, chapter, track, time code, etc., you want.

For example: Time Search To find a scene at 2 hours, 10 minutes, and 20 seconds, enter “21020.” If you make a mistake, press CLEAR to cancel the number, then select another number.

4 Press SET.

The recorder starts playback from the selected number.

Number buttons, SET

1 2 3

4 5 6

7 8 9

TOOLS

M/m, ENTER

1 Press TOOLS during playback.

The TOOLS menu appears.

2 Select a search method, and press ENTER.

“Title Search” (for DVDs) “Chapter Search” (for DVDs) “Track Search” (for CDs/DATA CDs) “Search” (for VIDEO CDs) “Album Search” (for DATA CDs) “Time Search” (for DVDs): Searches for a starting point by entering the time code.

The display for entering the number appears. Example: Title Search

Title : -- (21)

Playback

The number in parentheses indicates the total number of titles, tracks, etc.

RDR-GXD500

2-188-393-11(1)

Page 66

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 66 Mardi, 7. septembre 2004 9:41 09

Playing MP3 Audio Tracks

DATA CD

You can play MP3 audio tracks on DATA CDs (CD-ROMs/CD-Rs/CD-RWs).

1 2 3

4 5 6

7 8 9

master page=left

or Joliet format for the recorder to recognize the tracks. You can also play discs recorded in Multi Session. See the instructions supplied with the CD-R/CDRW drives and the recording software (not supplied) for details on the recording format.

Note on Multi Session discs

If MP3 audio tracks are recorded in the first session, the recorder will also play MP3 audio tracks in other sessions. If audio tracks in Music CD format are recorded in the first session, only the first session will be played back.

Playback order of MP3 audio tracks

Albums containing MP3 audio tracks play in the following order. A t B t C t D t F t G. Albums that do not contain tracks (such as album E) are skipped.

Tree 1 Tree 2 Tree 3 Tree 4 Tree 5

ROOT

1 Press Z (open/close), and place a disc on

the disc tray.

With the playback side facing down

2 Press Z (open/close) to close the disc

tray.

3 Press H.

Playback starts from the first MP3 audio tracks on the disc. Note that the playback order may be different from the edited order. See “Playback order of MP3 audio tracks” below.

About MP3 audio tracks

MP3 is audio compression technology that satisfies certain ISO/MPEG regulations. You can play back DATA CDs (CD-ROMs/CDRs/CD-RWs) recorded in MP3 (MPEG1 Audio Layer 3) format. However, the discs must be recorded according to ISO9660 Level 1, Level 2

Album

When you insert a DATA CD and press H, the numbered tracks are played sequentially, from 1 through 7. Any sub-albums/tracks contained within a currently selected album take priority over the next album in the same tree. (Example: C contains D so 4 is played before

5.)

MP3 audio track

RDR-GXD500

2-188-393-11(1)

Page 67

D:\DVD

manual\Final\218839311_FM\01GB07PLA.fm

01GB01.book Page 67 Mardi, 7. septembre 2004 9:41 09

z Hints

• You can view the disc information while playing MP3 audio tracks (page 36).

• If you add numbers (01, 02, 03, etc.) to the front of the track names when you store the tracks in a disc, the tracks will be played in that order.

• Since a disc with many trees takes longer to start playback, it is recommended that you create albums with no more than two trees.

Notes

• Depending on the software you use to create the DATA CD, the playback order may differ from the above illustration.

• Proceeding to the next or ano ther album may take some time.

• The recorder may not be able to play some DATA CDs created in the Packet Write format.

• The recorder will play any data with the extension “.MP3,” even if they are not in MP3 format. Playing this data may generate a loud noise which could damage your speaker system.

• The recorder does not conform to audio tracks in MP3PRO format.

• The playback order above may not be applicable if there are more than a total of 999 albums and tracks in the DATA CD.

• The recorder can recognize up to 499 albums (the recorder will count just albums, including albums that do not contain MP3 audio trac ks). The recorder will not play any albums beyond the first 499 albums. Of the first 499 albums, the recorder will play no more than a combined total of 999 albums and tracks.

• The recorder can play MP3 audio t racks recorded in the following sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz.

• Only the letters in the alphabet and numbers can be used for album or track names. Anything else is displayed as “*.”

• ID3 tags cannot be displayed.

master page=right

Playback

RDR-GXD500

2-188-393-11(1)

Page 68

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 68 Mardi, 7. septembre 2004 9:41 09

Editing

Before Editing

This recorder offers various edit options for various disc types. Before you edit, check the disc type in the front panel display, and select the option available for your disc (page 8).

Note

You may lose the edited contents if you remove the disc or a timer recording starts while editing.

Edit options for DVD+RWs/DVD-RWs (Video mode)/DVD+Rs/DVD-Rs

Video

You can perform simple edits. Since Video mode titles are actual recordings on the disc, you cannot undo any edits you make. The edit functions available for Video mode titles are: – Setting protection against erasure (page 69). – Labelling a title (page 69). – Erasing a title (page 69). – Erasing multiple titles (page 70). – Erasing a section of a title (A-B Erase)

(DVD+RWs only) (page 70).

– Erasing titles to open up disc space (Disc Map)

(DVD+RWs and DVD-RWs (Video mode) only) (page 71).

Notes

• Once the disc is finalized, you cannot edit or record on the disc (except for DVD+RWs and DVD-RWs (VR mode)).

• You cannot create a Playlist (see below).

• If a message appears and indicates that the disc’s control information is full, erase unnecessary titles.

Edit options for DVD-RWs (VR mode)

RWVR

You can enjoy advanced edit functions. First you have two options for a DVD-RW (VR mode): editing either the original recording (called the “original”), or the playback information created from the original (called a “Playlist”). Since each is different in nature and offers different merits, read the following and select the one that better suits your needs.

master page=left

To edit original titles

Edits made to the original titles are final. If you plan to retain an unaltered original recording, create and edit a Playlist (see below). The edit functions available for original titles are: – Labelling a title (page 69). – Setting protection against erasure (page 69). – Erasing a title (page 69). – Erasing multiple titles (page 70). – Erasing a section of a title (A-B Erase) (page 70).

To create and edit Playlist titles

A Playlist is a group of Playlist titles created from the original title for editing purposes. When you create a Playlist, only the control information necessary for playback, such as the playback order, is stored on the disc. Since the original titles are left unaltered, Playlist titles can be re-edited.

Example: You have recorded the final few matches of a football tournament on a DVD-RW (VR mode). You want to create a digest with the goal scenes and other highlights, but you also want to keep the original recording.

In this case, you can compile highlight scenes as a Playlist title. You can even rearrange the scene order within the Playlist title (“Creating and Editing a Playlist” on page 72).

The advanced edit functions available for Playlist titles are: – Labelling a title (page 69). – Erasing a title (page 69). – Erasing multiple titles (page 70). – Erasing a section of a title (A-B Erase) (page 70). – Rearranging the title order (page 74). – Dividing a title into multiple titles (page 74). – Combining multiple titles into one title

(page 75).

RDR-GXD5000

2-188-393-11(1)

Page 69

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 69 Mardi, 7. septembre 2004 9:41 09

z Hint

You can display the disc’s Playlist titles in the Title List (Playlist), or the original titles in the Title List (Original). To switch the two Title Lists, press TOOLS while a Title List is displayed, and select “Original” or “Playlist.”

Editing a Title

RWVR-RW

Video

master page=right

Notes

• The Playlist title calls up data from the original titles for playback. When an original title is used for a Playlist title, the original title cannot be erased.

• You cannot protect Playlist titles.

• If a message appears and indicates that the disc’s control information is full, erase unnecessary titles.

This section explains the basic edit functions. Note that editing is irreversible. To edit a DVD-RW (VR mode) without changing the original recordings, create a Playlist title (page 72).

Note

When editing a DVD+R, DVD-R, or DVD-RW (Video mode), finish all editing before finalizing the disc. You cannot edit a finalized disc.

1 2 3

4 5 6

7 8 9

TITLE LIST

TOOLS

</M/m/,, ENTER

m/M

CHAPTER MARK

MARK ERASE

Editing

1 Press TITLE LIST.

When editing a DVD-RW in VR mode, press TOOLS and select “Original” or “Playlist” from the TOOLS menu to switch the Title Lists, if necessary.

2 Select a title, and press ENTER.

The sub-menu appears.

3 Select an option, and press ENTER.

You can make the following edits to the title. “Erase”: Erases the selected title. Select “OK” when asked for confirmation. When the title is protected, the display asks for confirmation. To erase, select “Change,” and when the Protection display appears, select “Off.”

,continued

RDR-GXD5000

2-188-393-11(1)

Page 70

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 70 Mardi, 7. septembre 2004 9:41 09

master page=left

“Protect”: Protects the title. Select “On” when the Protection display appears. “ ” appears next to the protected title. To cancel the protection, select “Off.” “Title Name”: Allows you to enter or re-enter a title name (page 37). “Set Thumbnail”: Changes the title’s thumbnail picture that appears in the Title List (page 30). “A-B Erase”: Erases a section of the title (see below).

z Hints

• You can erase multiple titles at one time (page 70), or erase all of the titles on the disc at once (page 33).

• You can label or re-label DVDs (page 33).

Note

You cannot protect Playlist titles.

Erasing a section of a title (A-B Erase)

RWVR

You can select a section (scene) in a title and erase it. Note that erasing scenes in a title cannot be undone.

1 After step 2 of “Editing a Title,” select

“A-B Erase” and press ENTER.

The display for setting point A appears.

A-B Erase (Set point A) 2 DEF 20:00-21:00

2 Select point A by pressing m/M, and

press ENTER.

The display for setting point B appears.

A-B Erase (Set point B)

2 DEF 20:00-21:00

A 0:12:34 B 0:23:45

3 Select point B by pressing m/M, and

press ENTER.

The display asks for confirmation. To reset either point A or B, select “Change A” or “Change B,” and go to step 2 or 3.

4 Select “OK,” and press ENTER.

The scene is erased, and the display asks whether to erase another scene. To continue, select “Yes,” and repeat from step 2. To finish, select “No.”

z Hint

A chapter mark is inserted af ter the scene was erased. The chapter mark divides the title into separate chapters on either side of the mark.

Notes

• Images or sound may be momentarily interrupted at the point where you erase a section of a title.

• Sections shorter than five seconds may not be erased.

• For DVD+RWs, the erased section may be slightly different from the points you selected.

A 0:12:34

– – – – –

B : :

Playback point

• When the title is protected, the display asks for confirmation. To continue, select “Change,” and when the protection display appears, select “Off.”

Erasing multiple titles (Erase Titles)

RWVR-RW

Video

You can select and erase two or more titles at one time using the TOOLS menu.

1 Press TITLE LIST to turn on the Title List

menu, and press TOOLS.

The TOOLS menu appears.

2 Select “Erase Titles,” and press ENTER.

The display for selecting titles to be erased appears.

RDR-GXD5000

2-188-393-11(1)

Page 71

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 71 Mardi, 7. septembre 2004 9:41 09

master page=right

3 Select a title, and press ENTER.

A check mark appears in the check box next to the selected title. To clear the check mark, press ENTER again. To clear all of check marks, select “Reset All.”

Erase Titles

Select the titles to erase.

1 AAB 13:00-14:00 15. 9

2 DEF 20:00-21:00 17. 9

3 AAB 9:00- 9:30 25. 9

4 GHI 20:00-20:30 25. 9

5 DEF 20:00-20:30 15.10

Cancel

Reset All

• When the title is protected, the display asks for confirmation. To continue, select “Change,” and when the protection display appears, select “Off.” To cancel, select “Close.”

4 Repeat step 3 to select all of the titles you

want to erase.

5 When you finish selecting titles, select

“OK,” and press ENTER.

The list of the titles to be erased appears for confirmation. To change the selection, select “Change,” and repeat from step 3.

6 Select “OK” and press ENTER.

The titles are erased.

2 Press TOOLS and select “Disc Map,” and

press ENTER.

The Disc Map appears. To check the open space, select the space by pressing </,.

Disc Map

Empty Title

HQ: 0H30M

HSP: 0H45M

LP : 1H30M

Erase Cancel

b or B appears on either side of the

•When

SP: 1H00M

SLP: 3H00M

2.3GB

EP: 2H00M

Selected open space

screen, you can scroll sideways by pressing

</,.

3 Select a title by pressing </,, and

press ENTER.

The display for selecting titles to be erased appears. To cancel the selection, press ENTER again.

Disc Map

2 DEF 20:00- 21:00

Fri 17.9 20:00( 1H00M) SP 0.6GB

Editing

Erasing titles to open up disc space (Disc Map)

Video

When recording on a DVD+RW or DVD-RW (Video mode), the recorder searches for the largest open space and records there. Before you start, check the disc status by using Disc Map, and erase titles to create a space large enough for the recording.

1 Insert a disc and press TITLE LIST.

Erase Cancel

Selected title

• When the title is protected, the display asks for confirmation. To continue, select “Change,” and when the protection display appears, select “Off.” To cancel, select “Close.”

4 Repeat step 3 when erasing more titles. 5 Select “Erase,” and press ENTER.

The display asks for confirmation. To change the selection, select “Change.”

6 Select “OK,” and press ENTER.

The selected titles are erased, freeing up disc space.

,continued

RDR-GXD5000

2-188-393-11(1)

Page 72

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 72 Mardi, 7. septembre 2004 9:41 09

master page=left

Creating chapters manually

RWVR

You can manually insert a chapter mark at any point you like during playback or recording.

Press CHAPTER MARK at the point where you want to divide the title into chapters.

Each time you press the button, “Marking...” appears on the screen and the scenes to the left and right of the mark become separate chapters.

Marking...

To erase chapter marks

You can combine two chapters by erasing the chapter mark during playback. Press

./> to search for a chapter number, and

while displaying the chapter containing the chapter mark you want to erase, press MARK ERASE. The current chapter combines with the previous chapter.

Note

If a message appears and indicates that no more chapter marks can be added, you may not be able to record or edit.

Creating and Editing a Playlist

RWVR

Playlist edit allows you to edit or re-edit without changing the actual recordings. A Playlist title can contain up to 50 scenes. For details, see “Edit options for DVD-RWs (VR mode)” (page 68).

Note

Once you create a Playlist title from original titles, you will be unable to erase or edit the original titles.

1 2 3

4 5 6

7 8 9

TITLE LIST

TOOLS

</M/m/,, ENTER

m/M

1 Press TITLE LIST to turn on the Title List

menu, and press TOOLS.

The TOOLS menu appears.

2 Select “Create Playlist,” and press ENTER.

The display for selecting titles appears.

3 Select the title you want to include in the

Playlist title, and press ENTER.

A check mark appears in the check box next to the selected title. To clear the check mark, press ENTER again. To select all of the titles, select “Select All.”

Create Playlist

Select the titles you want to capture.

Original

1 AAB 13:00-14:00 15. 9

2 DEF 20:00-21:00 17. 9

3 AAB 9:00- 9:30 25. 9

4 GHI 0:00-20:30 25. 9

5 DEF 20:00-20:30 15.10

6 L3 21:00-21:30 19.10

Cancel

Select All

Reset All

RDR-GXD5000

2-188-393-11(1)

Page 73

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 73 Mardi, 7. septembre 2004 9:41 09

master page=right

4 Repeat step 3 to add more titles.

To go to the next page of titles, press m. To clear all of the check marks, select “Reset All.”

5 Select “OK,” and press ENTER.

The list of selected titles appears. To add another title, select “Add Title.”

Create Playlist - Selected Titles

Select a title to start capturing.

1 AAB 13:00-14:00 15. 9 0

2 DEF 20:00-21:00 17. 9 0

Scene List

Cancel

Add Title

6 Select one of the titles, and press ENTER.

The sub-menu appears. “Capture”: Adds a section of the title to the Playlist title as one scene. “Capture All”: Adds the entire title to the Playlist title as one scene. After capturing the title, select “Scene List” and go to step 12. “Check Scenes”: Allows you to check the captured scene.

7 Select “Capture,” and press ENTER.

The display for setting the start point (IN) appears. The title starts to play in the background.

Capture (Set IN point) 2 DEF 20:00-21:00

0:10:26

OUT - : - - : - -

8 Select the IN point by pressing m/M,

and press ENTER.

The display for setting the end point (OUT) appears, and the title continues to play in the background.

Capture (Set OUT point) 2 DEF 20:00-21:00

0:10:26

OUT 0:23:45

9 Select the OUT point by pressing m/M,

and press ENTER.

The display asks for confirmation. To reset the IN or OUT point, select “Change IN” or “Change OUT” and repeat step 8 or 9. To view the selected scene, select “Preview.”

10Select “OK,” and ENTER.

The selected section is captured as a scene, and the display asks whether you want to continue. To continue, select “More,” and repeat the steps above. To capture a scene from another title, select “New Title.”

11When you finish capturing scenes, select

“No More” and press ENTER.

The Scene List menu appears with all of the selected scenes.

Total duration of the selected scene

Scene List Total 0:33:28 Scenes 2

DEF 20:00-21:00

0:10:26 - 0:23:45

DEF 20:00-21:00

0:25:00 - 0:45:08

Total number of scenes

Quit

Add

Preview

12Select the scene you want to edit, and

press ENTER.

The sub-menu appears. “Move”: Changes the scene order. “Erase”: Erases the scene. The selection is cancelled. “Preview”: Displays thumbnail pictures of the scenes. “Change IN”: Allows you to change the IN point, and repeat from step 8. “Change OUT”: Allows you to change the OUT point, and repeat from step 9. To add more scenes, select “Add” and go to step 6. To preview all of the captured scenes in the listed order, select “Preview.”

13When you finish editing the Scene List,

select “OK,” and press ENTER.

The display for entering the title name appears. To enter a new name, select “Enter” (see page 37).

14Select “OK” to use the default name, and

press ENTER.

Editing

,continued

RDR-GXD5000

2-188-393-11(1)

Page 74

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 74 Mardi, 7. septembre 2004 9:41 09

master page=left

To play the Playlist title

Press TOOLS while the Title List menu is turned on. Then, select “Playlist” and press ENTER. When the Title List (Playlist) menu appears, select a title and press H.

z Hint

When a Playlist title is created, the IN and OUT points will become chapter marks, and each scene will become a chapter.

Note

The picture may pause when the edited scene is played.

Moving a Playlist title (Move)

RWVR

You can change the Playlist title order within the Title List (Playlist).

1 Press TITLE LIST to turn on the Title List

(Playlist) menu.

If the Title List (Original) menu appears, press TOOLS and select “Playlist.”

2 Select “Number” in the “Sort” column,

and press ENTER.

The titles are sorted in order of title number.

3 Select a title, and press ENTER.

The sub-menu appears.

4 Select “Move,” and press ENTER.

Move

1 AAB 13:00 - 14:00

Where do you want to move this title?

2 DEF 8:00 - 9:00

15.9

Wed

Fri

Cancel

17.9

Dividing a Playlist title (Divide)

RWVR

1 Press TITLE LIST to turn on the Title List

(Playlist) menu.

If the Title List (Original) menu appears, press TOOLS and select “Playlist.”

2 Select a title, and press ENTER.

The sub-menu appears.

3 Select “Divide,” and press ENTER.

The display for setting the dividing point appears. The title starts to play in the background.

Divide 1 ABC 13:00-14:00

0:12:34

4 Select the dividing point by pressing

m/M, and press ENTER.

The display asks for confirmation. To change the dividing point, select “Change.”

5 Select “OK,” and press ENTER.

The display for entering the title name appears. To use the same title name as before, select “No.”

6 Select “Yes,” and press ENTER to enter a

new name.

Follow the explanations on page 37. After you enter a new name, the title is divided in two.

5 Select a new location for the title by

pressing M/m, and press ENTER.

The title moves to the new location.

RDR-GXD5000

2-188-393-11(1)

Page 75

D:\DVD

manual\Final\218839311_FM\01GB08EDIT.fm

01GB01.book Page 75 Mardi, 7. septembre 2004 9:41 09

Combining multiple Playlist titles (Combine)

RWVR

1 Press TITLE LIST to turn on the Title List

(Playlist) menu.

If the Title List (Original) menu appears, press TOOLS and select “Playlist.”

2 Press TOOLS to select “Combine,” and

press ENTER.

The display for selecting titles appears.

3 Select a title, and press ENTER.

A number indicating the order in which you selected the title appears. To cancel the selection, press ENTER again.

master page=right

Combine

Select the titles to combine.

1 AAB 13:00-14:00 15. 9

2 DEF 20:00-21:00 17. 9

3 AAB 13:00-14:00 28. 9

4 AAB 13:00-14:00 5. 10

Cancel

Reset All

4 Repeat step 3 to select all of the titles you

want to combine.

To cancel all of the selections, select “Reset All.”

5 Select “OK,” and press ENTER.

The list of titles to be combined appears. To change the selection, select “Change” and go to step 3.

Combine

Combine the titles in the following order.

1 AAB 13:00-14:00

3 AAB 13:00-14:00

4 AAB 13:00-14:00

OK Change Cancel

15. 9

28. 9

5.10

6 Select “OK,” and press ENTER.

The display for selecting a title name from among the selected titles appears. To enter a new name, select “Enter Text,” and follow the explanations on page 37.

7 Select a name, and press ENTER.

The titles are combined.

Editing

RDR-GXD5000

2-188-393-11(1)

Page 76

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 76 Mardi, 7. septembre 2004 9:41 09

master page=left

Settings and Adjustments

Using the Setup Displays

By using the Setup Displays, you can make various adjustments to items such as picture and sound, as well as select a language for the subtitles or Digital TV features settings. The Setup Displays are used in the following way.

Note

Playback settings stored in the disc take priority over the Setup Display settings, and not all of the functions described may work.

1 2 3

4 5 6

7 8 9

SYSTEM MENU

</M/m/,, ENTER

1 Press SYSTEM MENU while the recorder is

in stop mode.

The System Menu appears.

SETUP

Settings

Clock

DTV Settings

Language

Video

Audio

Features

Password

Options

Easy Setup

3 Select “Settings,” “DTV Settings,”

“Video,” “Audio,” “Features,” “Password,” “Options,” or “Easy Setup,” and press ENTER.

The selected Setup Display appears. Example: “Video” setup

SETUP

Settings

DTV Settings

Video

Audio

Features

Password

Options

Easy Setup

TV Type : Pause Mode : Component Out : Screen Saver : Scart Setting Line4 input :

16 : 9 Auto Off On

Video

4 Select the item you want to set up, and

press ENTER.

Available options for the item appear. Example: “TV Type”

SETUP

Settings

DTV Settings

Video

Audio

Features

Password

Options

Easy Setup

TV Type : Pause Mode : Component Out : Screen Saver : Scart Setting Line4 input :

16 : 9

Auto

4 : 3 Letter Box

Off

4 : 3 Pan Scan

Video

SYSTEM MENU

TITLE LIST

EPG

TIMER LIST

SETUP

2 Select “SETUP,” and press ENTER.

The Setup Display appears.

5 Select an option, and press ENTER.

The currently selected option is displayed next to the setup item. Example: when “4:3 Letter Box” is set.

SETUP

Settings

TV Type :

DTV Settings

Pause Mode :

Video

Component Out :

Audio

Screen Saver :

Features

Scart Setting

Password

Line4 input :

Options

Easy Setup

To turn off the display

Press SYSTEM MENU repeatedly.

4 : 3 Letter Box Auto Off On

Video

RDR-GXD500

2-188-393-11(1)

Page 77

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 77 Mardi, 7. septembre 2004 9:41 09

Aerial Reception and Language Settings (Settings)

master page=right

5 Press ENTER to start the clock. 6 Press the O button to come back to the Clock

menu.

Language

The Settings Setup helps you to make clock and language settings for the recorder.

Select “Settings” in the Setup Display. To use the display, see “Using the Setup Displays” (page 76).

SETUP

Settings

Clock

DTV Settings

Language

Video

Audio

Features

Password

Options

Easy Setup

Clock

Normally the clock is set automatically thanks to the time and date information broadcasted by the local network package. If the recorder does not receive a time signal from any service, you may set the clock manually. Therefore, please proceed as follows.

◆To set the clock manually

1 Follow steps 1 to 3 of “Using the Setup

Displays” (page 76) to select “Settings” in the Setup Display.

2 Select “Clock,” and press ENTER.

Settings - Clock

Present Time : Wed 20. 10. 2004 21:39

DVD Menu (DVD VIDEO only)

Switches the language for the DVD menu.

Audio

Switches the language of the sound track. When you select “Original,” the language given priority in the disc (DVD VIDEO only) or broadcasted by a digital channel is selected.

Subtitle

Switches the language of the subtitles recorded on the disc (DVD VIDEO only) or broadcasted by a digital channel (when available). When you select “Audio Follow,” the subtitle language changes according to the language you selected for the sound track.

Settings and Adjustments

z Hint

If you select “Others” in “DVD Menu,” “Subtitle,” or “Audio,” select and enter a language code from “Language Code List” (page 104) using the number buttons.

Note

If you select a language in “DVD Menu,” “Subtitle,” or “Audio” that is not recorded on the DVD VIDEO, one of the recorded languages will be automatically selected.

3 Select “Present Time,” and press ENTER.

Clock - Present Time

Set the time and date manually.

10 2004

Wed 20

0 00:

4 Press M/m to set the day, and press ,.

Set the month, year, hour, and minutes in sequence. Press </, to select the item to be set, then press M/m to set the numbers. The day of the week is set automatically.

To change the numbers, press < to return to the item to be changed, and press M/m.

RDR-GXD500

2-188-393-11(1)

Page 78

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 78 Mardi, 7. septembre 2004 9:41 09

Digital TV settings (DTV Settings)

The DTV Settings Setup enables you to take full advantage of Digital TV Broadcasting services such as favourites channels setting or to prevent children’s viewing unsuitable channels and programmes.

master page=left

• If you have not yet registered a password, the display for registering a new password appears.

DTV Settings - Parental Lock

Enter a new password.

Cancel

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “DTV Settings,” and press ENTER.

The DTV Settings Setup Display appears with the following options.

SETUP

Settings

Favourites

DTV Settings

Parental Lock

Video

Tuning

Audio

Technical information

Features

Password

Options

Easy Setup

Favourites

The Favourite Display allows you to store and organize your favourite channels into one of four TV or four Radio lists. Please refer to page 42 for detailed Favourites Channels settings

Parental Lock

The Parental Lock Display enables you to lock certain channels you consider unsuitable and to set an age limit so that any programme classed above that age by the broadcaster is restricted.

1 After step 3 above, select “Parental Lock,”

and press ENTER.

• When you have already registered a password, the display for entering the password appears.

DTV Settings - Parental Lock

Enter your password.

Cancel

2 Enter your four-digit password using the M/m

buttons or the number buttons, then select “OK” and press ENTER.

The Parental Lock menu appears

DTV Settings - Parental Lock

Lock Channels Set Age Limit

Note

If you forget your password, you will have to reset it by selecting “Password” under “Factory Setup” in Options Setup (page 90).

◆To lock channels

1 Once the Parental Lock menu displayed,

select “Lock Channels,” and press ENTER.

The DTV Settings- Lock Channels display appears.

Lock Channels

Page Up Page Down Show Locked

Programme 001 002 003 004 005

Service DDE News AAC NCE 5 Channel J Digital Teletext

This display shows all the TV channels available to you.

2 Press the M/m buttons or enter a channel

number to highlight a channel you want to lock, then press the ENTER button.

A locked channel is identified by the icon next to the programme number

RDR-GXD500

2-188-393-11(1)

Page 79

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 79 Mardi, 7. septembre 2004 9:41 09

master page=right

Lock Channels

Page Up Page Down Show Locked

Programme 001 002 003 004 005

Service DDE News AAC NCE 5 Channel J Digital Teletext

If you do not wish to lock one of the five channels in the display, press the RED or GREEN button to view the previous or next five channels available.

3 Press the O button to come back to the

Parental Lock menu.

◆To unlock channels

1 In Step 2 above press the M/m buttons to

highlight the channel you want to unlock, then press ENTER: the icon next to the programme number disappears.

2 Press the O button to come back to the

Parental Lock menu.

z Hints

• Press the BLUE button to view the list showing only the locked channels.

• Press the BLUE button once again when you wish to return to the previous channel list display.

◆ To set the Age Limit

1 Once the Parental Lock menu displayed,

select “Set Age Limit,” and press ENTER.

Set Age Limit

An event will be locked when it is rated as

unsuitable children below the following age:

Age:

2 Press the M/m buttons to set the desired age

limit and press ENTER.

Notes

• To operate correctly, this feature relies on the broadcaster sending the correct age classification for each programme.

• If you select the Parental Lock channel activated, “This channel has been locked” appears on the gray screen and it is recorded.

Tuning

The Tuning Display allows you to tune your recorder automatically or manually and also change the order of the programmes on display. During these procedures you may be requested to enter your password. Refer to page 78 for information.

Follow steps 1 to 3 of “Digital TV settings (DTV Settings)” on page 78, then select “Tuning,” and press ENTER.

Tuning

Auto Tune Manual Tune Programme Sort

The DTV Settings - Tuning menu appears.

Auto Tune

This option enables you to capture and store automatically all available channels.

1 Once the DTV Settings - Tuning menu

displayed, select “Auto Tune,” and press ENTER. The Auto Tune Start Display appears.

Auto Tune

Do you want to start auto tuning ?

If you have preset any timer recordings

they will be erased.

Ye s N o

2 Select “Yes” in the menu option and press

ENTER. The Auto Tune display appears showing a tuning progress bar and the number of channels found.

Auto Tune

Number of channels found

Searching ...

Settings and Adjustments

,continued

RDR-GXD500

2-188-393-11(1)

Page 80

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 80 Mardi, 7. septembre 2004 9:41 09

master page=left

When Auto Tune has ended, a completion display appears indicating the number of TV and Radio channels that have been found and stored.

Auto Tune

Number of channels found

Number of TV Channels

Number of Radio Channels

Tuning has sucessfully completed

3 Press the ENTER button to remove the

display and view the first channel captured.

Manual Tune

This option allows you to capture and store individual services.

1 Once the DTV Settings - Tuning menu

displayed, select “Manual Tune,” and press ENTER.

The Manual Tune Display appears showing a list of all the channels previously captured and stored.

Manual Tune

Page Up Page Down

Programme 001 002 003 004 005

UHF Channel 50 50 43 43 40

Service DDE News AAC NCE 5 Channel J Digital Teletext

If you want to display the previous or next five available channels, press the RED or GREEN button on your remote control.

2 Press the M/m buttons or enter a channel

number to select the programme number of your choice, then press the ENTER button.

The Tuning screen appears with the selected channel on view in the background

Manual Tune

Programme: 003

Service: NC5

UHF Channel: Search:

Search Up

Search Down

Status: Not Searching

3 Press the ,/M/m button to highlight either

‘Search Up’ or ‘Search Down’ then press the ENTER button to begin searching up or searching down.

The Service searching process starts.

Manual Tune

Programme: 003

Service: NC5

UHF Channel: Search:

Search Up

Search Down

Status: Searching...

After a while, when a service is found, the display shows a list of captured channels.

Manual Tune

Programme: 003

Service: NC5

UHF Channel: Search:

Search Up

Search Down

6 Services found:

DDE News AAC NCE 5 Channel J Digital Teletext

4 Press the M/m buttons to move arround the

list. Once the channel you wish to store is highlighted, press the ENTER button.

5 Once you have stored your desired channel,

press the RETURN button repeatedly to return to the main menu.

Note

After tuning, your receiver will continually monitor broadcast information to check for new channels. Should a new channel become available, it is detected and automatically added to your programme list. Normally it will then be available to view. However, if you notice a new channel that you are unable to view, please tune it in manually using the ‘Manual Tune’ procedure as explained above.

RDR-GXD500

2-188-393-11(1)

Page 81

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 81 Mardi, 7. septembre 2004 9:41 09

master page=right

Programme Sort

This option allows you to change the channel order in the on-screen programme list.

1 Once the DTV Settings - Tuning menu

displayed, select “Programme Sort,” and press ENTER. The Programme Sort Display appears showing the list of all tuned channels.

Programme Sort

Programme 001 002 003 004 005

Page Up Page Down

Service DDE News AAC NCE 5 Channel J Digital Teletext

2 Press the M/m buttons or enter a programme

number to highlight the channel you wish to move, then press the ENTER button. A tick icon appears next to the selected programme number and a Swap option appears in the display.

Programme Sort

Programme 001 002 003 004 005

Page Up Page Down

Service DDE News AAC NCE 5 Channel J Digital Teletext

Swap

If you do not wish to choose from one of the five channels in the display, press the RED or GREEN button to view the previous or next five channels available.

3 Press the M/m buttons to highlight the

programme number you wish your selected channel to appear on.

Programme Sort

Programme 001 002 003 004 005

Page Up Page Down

Service DDE News AAC NCE 5 Channel J Digital Teletext

Swap

4 Press the BLUE button to swap channel

position. Your selected channel appears on the programme number selected in step 3.

5 Repeat this procedure to move other channels. 6 Once you have moved all channels as desired,

press the RETURN button repeatedly to return to the main menu.

Technical Information

Follow steps 1 to 3 of “Digital TV settings (DTV Settings)” on page 78, then select “Technical Information,” and press ENTER.

Technical Information

Manufacturer Information Signal Strength Digital Software Upgrade : On

The DTV Settings - Technical Information menu appears.

Manufacturer Information

This information screen shows you the current version of software installed in your recorder.

1 Once the DTV Settings - Technical

Information displayed, select “Manufacturer Information,” and press ENTER.

Manufacturer Information

Software Version v1.00.09 U Loader Version v1.02 Hardware Version K-000-000-00

2 After viewing the information displayed,

press the Technical Information menu.

Signal Strength

This information screen shows the signal strength of the broadcast you are watching.

O button to come back to the

1 Select “Signal Strength,” in the DTV Settings

- Technical Information display and press ENTER. The Signal Strength display appears with the selected channel on view in the background.

Signal Strength

Signal Strength Good

Signal Quality Average

The Signal Strength display coloured bars correspondences are as follows:

Good: (Green) Average: (Yellow) Poor: (Red)

2 Press the PROG +/– buttons to check the

signal strength of the other tuned channels.

3 After viewing the information displayed,

press the Technical Information menu.

O button to come back to the

,continued

Settings and Adjustments

RDR-GXD500

2-188-393-11(1)

Page 82

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 82 Mardi, 7. septembre 2004 9:41 09

Digital Software Upgrade

Periodically Sony will issue upgrades for the software that was initially installed in your recorder. These upgrades will automatically be received and enabled. If desired, you can disable this option as follows:

1 Select “Digital Software Upgrade,” in the

DTV Settings - Technical Information display and press ENTER.

The Digital Software Upgrade menu option appears

Technical Information

Manufacturer Information Signal Strength Digital Software Upgrade : On

On Off

master page=left

Video Settings (Video)

Video settings will adjust items related to the image, such as size and colour. Choose the settings according to the type of TV, tuner, or decoder connected to the DVD recorder.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Video,” and press ENTER.

The Video Setup appears with the following options. The default settings are underlined.

2 Press the M/m buttons to highlight “Off,” and

press ENTER.

Notes

• Sony recommend that you always leave this option set to “On”.

• To receive the upgrade, the unit must be powered on and watching a BBC channel. It will take up 30minutes to upgrade the unit. The new software will be available once the unit has been placed into standby, and then back to normal operating mode.

SETUP

Settings

DTV Settings

Video Audio

Features

Password

Options

Easy Setup

TV Type : Pause Mode : Component Out : Screen Saver : Scart Setting Line4 input :

16 : 9 Auto Off On

Video

TV Type

Selects the aspect ratio of the connected TV (4:3 standard or wide).

16:9 Select this when connecting

to a wide-screen TV or TV with a wide mode function.

4:3 Letter Box

Select this when connecting to a 4:3 screen TV. Displays a wide picture with bands on the upper and lower portions of the screen.

4:3 Pan Scan

Select this when connecting to a 4:3 screen TV. Automatically displays a wide picture on the entire screen and cuts off the portions that do not fit.

RDR-GXD500

2-188-393-11(1)

Page 83

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 83 Mardi, 7. septembre 2004 9:41 09

master page=right

16:9

4:3 Letter Box

4:3 Pan Scan

Note

Depending on the disc, “4:3 Letter Box” may be selected automatically instead of “4:3 Pan Scan” or vice versa.

Pause Mode (DVDs only)

Selects the picture quality in pause mode.

Auto The picture, including subjects

Frame The picture, including subjects

that move dynamically, is output with no jitter. Normally select this position.

that do not move dynamically, is output in high resolution.

Component Out

Selects whether or not to output video signals from the COMPONENT VIDEO OUT jacks.

On Outputs the component video

Off

signals.

Outputs no signals.

Notes

• When you set “Line1 Output” to “RGB,” you cannot set “Component Out” to “On.”

• When you connect the recorder to a monitor or projector via only the COMPONENT VIDEO OUT jacks, do not select “Off.” If you select “Off” in this case, the picture may not appear.

Screen Saver

The screen saver image appears when you do not use the recorder for more than 10 minutes while an on-screen display, such as the System Menu, is displayed on your TV screen. The screen saver image helps prevent your display device from becoming damaged (ghosting).

On Turns on the screen saver

Off Turns off the function.

function.

Scart Setting

Sets the method of inputting/outputting signals from the SCART jacks on the rear panel of the recorder. Select an option for each of the items below according to the combination of jacks and methods that you are going to use.

◆Line1 Output

Selects a method of outputting video signals for the LINE 1-TV jack.

RGB Outputs RGB signals.

Video

S Video Outputs S-video signals.

Outputs video signals.

Notes

• If your TV does not accept S-video or RGB signals, no picture appears on the TV screen even if you select “S Video” or “RGB.” See the instructions supplied with your TV.

• You cannot select ”RGB” when “Component Out” above is set to “On.”

• SMARTLINK is available only when “Video” is selected.

◆Line3 Input

Selects a method of inputting video signals for the LINE 3 jack. The pictures will not be clear if this setting does not match the type of video input signal.

Video/RGB

S Video Inputs S-video signals.

Inputs video signals or RGB signals.

Settings and Adjustments

,continued

RDR-GXD500

2-188-393-11(1)

Page 84

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 84 Mardi, 7. septembre 2004 9:41 09

◆Line3 Output

Selects a method of outputting video signals for the LINE 3 jack.

Video Outputs video signals.

S Video Outputs S-video signals.

master page=left

Audio Settings (Audio)

The Audio Setup allows you to adjust the sound according to the playback and connection conditions.

Line4 Input

Selects a method of inputting video signals for the LINE 4 IN jack on the rear panel of the recorder.

Video

Inputs video signals.

S Video Inputs S-video signals.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Audio,” and press ENTER.

The Audio Setup appears with the following options. The default settings are underlined.

SETUP

Audio ATT :

Settings

Audio DRC :

DTV Settings

Downmix :

Video

Digital Out :

Audio

Dolby Digital :

Features

MPEG :

Password

DTS :

Options

Easy Setup

Audio ATT (attenuation)

If the playback sound is distorted, set this item to “On.” The recorder reduces the audio output level. This function affects the output of the following jacks: – LINE 2 OUT AUDIO L/R jacks – LINE 1-TV jack – LINE 3 jack

On Select this when the

playback sound from the speakers is distorted.

Off Standard Dolby Surround On D-PCM PCM Off

Off

Normally select this position.

RDR-GXD500

2-188-393-11(1)

Page 85

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 85 Mardi, 7. septembre 2004 9:41 09

master page=right

Audio DRC (Dynamic Range Control) (DVDs only)

Makes the sound clear when the volume is turned down when playing a DVD that conforms to “Audio DRC.” This affects the output from the following jacks: – LINE 2 OUT AUDIO L/R jacks – LINE 1-TV jack – LINE 3 jack – DIGITAL OUT (OPTICAL or COAXIAL) jack

only when “Dolby Digital” is set to “D-PCM” (page 85).

Standard Normally select this

position.

TV Mode Makes low sounds clear

even if you turn the volume down.

Wide Range

Gives you the feeling of being at a live performance.

Downmix (DVDs only)

Switches the method for mixing down to two channels when you play a DVD which has rear sound elements (channels) or is recorded in Dolby Digital format. For details on the rear signal components, see “Checking the Play Information and Playing Time” (page 35). This function affects the output of the following jacks: – LINE 2 OUT AUDIO L/R jacks – LINE 1-TV jack – LINE 3 jack – DIGITAL OUT (OPTICAL or COAXIAL) jack

when “Dolby Digital” is set to “D-PCM” (page 85).

Dolby Surround

Normally select this position. Multi-channel audio signals are output to two channels for enjoying surround sounds.

Normal Multi-channel audio signals

are downmixed to two channels for use with your stereo.

Digital Out

Selects if audio signals are output via the DIGITAL OUT (OPTICAL or COAXIAL) jacks.

On Normally select this

position. When you select “On,” see “To set the digital output signal” for further settings.

Off The influence of the digital

circuit upon the analogue circuit is minimal.

◆To set the digital output signal

The following setup items switch the method of outputting audio signals when you connect a component such as an amplifier (receiver) with a digital input jack. For connection details, see “Connecting the Audio Cords” (page 17). Select “Dolby Digital,” “MPEG,” and “DTS” after setting “Digital Out” to “On.”

SETUP

Settings

DTV Settings

Video Audio

Features

Password

Options

Easy Setup

Audio ATT : Audio DRC : Downmix : Digital Out : Dolby Digital : MPEG : DTS :

Off Standard Dolby Surround On D-PCM PCM Off

If you connect a component that does not accept the selected audio signal, a loud noise (or no sound) will come out from the speakers, and may affect your ears or cause speaker damage.

• Dolby Digital (DVDs only)

Selects the type of Dolby Digital signal.

D-PCM

Select this when the recorder is connected to an audio component lacking a built-in Dolby Digital decoder. You can select whether the signals conform to Dolby Surround (Pro Logic) or not by making adjustments to the “Downmix” item in Audio Setup (page 85).

Settings and Adjustments

Dolby Digital

Select this when the recorder is connected to an audio component with a built-in Dolby Digital decoder.

,continued

RDR-GXD500

2-188-393-11(1)

Page 86

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 86 Mardi, 7. septembre 2004 9:41 09

• MPEG (DVD VIDEO only) Selects the type of MPEG audio signal.

PCM Select this when the recorder

is connected to an audio component without a built-in MPEG decoder. If you play MPEG audio sound tracks, the recorder outputs stereo signals via the DIGITAL OUT (COAXIAL) jack.

MPEG Select this when the recorder

is connected to an audio component with a built-in MPEG decoder.

• DTS (DVD VIDEO only) Selects whether or not to output DTS signals.

master page=left

Recording and Parental Control Settings (Features)

The Features Setup allows you to adjust recording and parental control settings.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Features,” and press ENTER.

The Features Setup appears with the following options. The default settings are underlined.

On Select this when the recorder

is connected to an audio component with a built-in DTS decoder.

Off

Select this when the recorder is connected to an audio component without a built-in DTS decoder.

Note

When you use the DIGITAL OUT (COAXIAL) jack to listen to MPEG audio signals and set “MPEG” to “MPEG” in Audio Setup, no sound will come from your speakers if you select one of the TVS modes.

SETUP

Settings

DTV Settings

Video

Audio

Features

Password

Options

Easy Setup

TV Direct Rec : Auto Chapter : Parental Control Colour System :

On 6 Min

PAL

TV Direct Rec (DVD+RW/DVD-RW/DVD+R/ DVD-R only)

On Allows you to easily record

Off Turns off the TV Direct Rec

what you are watching on the TV using SMARTLINK.

function.

Auto Chapter

Automatically divides a recording (a title) into chapters by inserting chapter markings at a specified interval. The markings are inserted while the recording is being made.

Off No chapter mark is inserted.

6Min

Inserts chapter marks at approximately 6-minute intervals.

15Min Inserts chapter marks at

approximately 15-minute intervals.

RDR-GXD500

2-188-393-11(1)

Page 87

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 87 Mardi, 7. septembre 2004 9:41 09

master page=right

Notes

• Depending upon the size of the recording being made, the actual interval may vary from the interval selected in “Auto Chapter.” The selected interval should only be used as an approximation to create chapters.

• Chapter marks are automatically entered where the recordings starts.

Parental Control (DVD VIDEO only)

Playback of some DVD VIDEOs can be limited according to a predetermined level, such as the age of the users. Scenes may be blocked or replaced with different scenes.

1 After step 3 above, select “Parental Control,”

and press ENTER.

• If you have not entered a password, the display for registering a new password appears.

Features - Parental Control

Enter a new password.

Cancel

• When you have already registered a password, the display for entering the password appears.

Features - Parental Control

Enter your password.

Cancel

4 Select a geographic area as the playback

limitation level, and press ENTER. The area is selected.

• When you select “Others,” press the number buttons to select and enter an area code in the table (see below). Then select “OK” and press ENTER.

5 Select “Level,” and press ENTER.

The selection items for “Level” are displayed.

Features - Parental Control

Level : Standard :

Off

Off Others

8 7 6 5 4

The lower the value, the stricter the limitation.

6 Select the level, and press ENTER.

The Parental Control setting is complete.

To cancel the Parental Control setting for the disc, set “Level” to “Off” in step 6. To change the password, you will have to set it in the Password Setup Display(page 89).

Notes

• If you forget your password, you will have to reset it by selecting “Password” und er “Factory Setup” in Options Setup (page 90).

• When you play discs which do not have the Parental Control function, playback cannot be limited on this recorder.

• Depending on the disc, you may be asked to change the Parental Control level while playing the disc. In this case, enter your password, then change the level.

Settings and Adjustments

2 Enter your four-digit password using the

number buttons, then select “OK” and press ENTER.

Features - Parental Control

Level : Standard :

Off USA

3 Select “Standard,” and press , or ENTER.

The selection items for “Standard” are displayed.

Features - Parental Control

Level : Standard :

Off Others

USA Others

,continued

RDR-GXD500

2-188-393-11(1)

Page 88

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 88 Mardi, 7. septembre 2004 9:41 09

master page=left

◆Area code

Standard Code number

Argentina 2044 Australia 2047 Austria 2046 Belgium 2057 Brazil 2070 Canada 2079 Chile 2090 China 2092 Denmark 2115 Finland 2165 France 2174 Germany 2109 India 2248 Indonesia 2238 Italy 2254 Japan 2276 Korea 2304 Malaysia 2363 Mexico 2362 Netherlands 2376 New Zealand 2390 Norway 2379 Pakistan 2427 Philippines 2424 Portugal 2436 Russia 2489 Singapore 2501 Spain 2149 Sweden 2499 Switzerland 2086 Thailand 2528 United Kingdom 2184

Colour System

Selects the colour system when playing VIDEO CDs (including Super VCDs).

PAL Plays a disc in PAL colour

system.

NTSC Plays a disc in NTSC colour

system.

RDR-GXD500

2-188-393-11(1)

Page 89

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 89 Mardi, 7. septembre 2004 9:41 09

master page=right

Parental Control (Password)

This Password Setup allow you to set or to modify the password that gives access to Parental Control settings.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Password,” and press ENTER.

The Password Setup Display appears

• If you have not yet set a password, the display for registering a new password appears.

Passwo rd

Enter a new password.

Cancel

• When you have already registered a password, the display for entering the password appears.

Passwo rd

Enter your password.

Cancel

Disc and Remote Control Settings/Factory Settings (Options)

The Options Setup allows you to set up other operational settings.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Options,” and press ENTER.

The Options Setup appears with the following options. The default settings are underlined.

SETUP

Settings

Format DVD :

DTV Settings

Dimmer :

Video

Auto Display :

Audio

Command Mode :

Features

Factory Setup

Password

Options

Easy Setup

Format DVD (DVD-RW only)

The recorder automatically starts formatting in VR mode or Video mode, whichever is selected below, when a new, unformatted DVD-RW is inserted.

VR Automatically formats the

disc in VR mode.

VR Normal On DVD3

Settings and Adjustments

If you wish to change your password, first enter your current password using the number buttons, then select “OK” and press ENTER. The display for registering a new password appears.

4 Enter your new four-digit password using

the number buttons, then select “OK” and press ENTER.

Note

If you forget your password, you will have to reset it by selecting “Password” under “Factory Setup” in Options Setup (page 90).

Video Automatically formats the

disc in Video mode.

Dimmer

Adjusts the lighting of the front panel display.

Normal

Power Save

Bright lighting.

Low lighting. Turns off the lighting when the power is off.

,continued

RDR-GXD500

2-188-393-11(1)

Page 90

D:\DVD

manual\Final\218839311_FM\01GB10ADJ.fm

01GB01.book Page 90 Mardi, 7. septembre 2004 9:41 09

Auto Display

On Automatically displays

information on the screen when the recorder is turned on, etc.

Off Displays information only

when DISPLAY is pressed.

Command Mode

Changes the Command Mode of the recorder if other DVD equipment is assigned the same Command Mode. Be sure to match the Command Mode switch on the remote to the setting made here. For details, see “If you have a Sony DVD player or more than one Sony DVD recorder” on page 21.

DVD1 Select this if the default

Command Mode conflicts with other DVD equipment.

master page=left

Easy Setup (Resetting the Recorder)

Select this to run the Easy Setup programme.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “SETUP,” and press ENTER. 3 Select “Easy Setup,” and press ENTER.

SETUP

Settings

Easy Setup

DTV Settings

Video

Audio

Features

Password

Options

Easy Setup

DVD2 Select this if the default

DVD3

Command Mode conflicts with other DVD equipment.

The default Command Mode of the recorder.

Factory Setup

Allows you to select the setup settings by group, and return them to their default settings. Note that all of your previous settings will be lost.

1 After step 3 above, select “Factory Setup,”

and press , or ENTER. The display for selecting a group of settings appears.

2 Select the group of settings you want to return

to default from “Settings,” “DTV Settings,” “Video,” “Audio,” “Features,” “Options,” “Password,” and “All,” and press , or ENTER.

3 Select “Start,” and press ENTER.

The selected settings return to their default settings.

4 Press ENTER when “Finish” appears.

4 Select “Start,” and press ENTER. 5 Follow the instructions for Easy Setup

from step 4 (page 23).

RDR-GXD500

2-188-393-11(1)

Page 91

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 91 Mardi, 7. septembre 2004 9:41 09

Additional Information

Troubleshooting

If you experience any of the following difficulties while using the recorder, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, contact the Sony Customer Information Centre on

08705 111 999

(Monday-Friday from 8:30am to 6:00pm)

Power

The power does not turn on.

, Check that the mains lead is connected securely.

Tuner

The channel is not found or stored or missed

, Make sure that your aerial is properly connected

to the recorder.

, Confirm with your dealer that you are in an area

that can receive a digital signal.

, Check your aerial installation.

master page=right

quality. If you still experience this problem even when you connect your recorder directly to your TV, try connecting your recorder to your TV’s S VIDEO input.

, You are playing a disc recorded in a colour

system that is different from your TV.

TV programme reception does not fill the screen.

, Select the correct source using the INPUT

SELECT button, or select a channel of any TV programme using the PROG +/– buttons.

Picture break up

, Signal strength low , Check aerial installation

TV programme pictures are distorted.

, Reorient or upgrade the TV aerial. , Adjust the picture (see the TV’s instruction

manual).

, Place the recorder and TV farther apart. , Place the TV and any bunched aerial cables

farther apart.

, The RF cable is connected to the AERIAL OUT

jack on the recorder. Connect the cable to the AERIAL IN jack.

Additional Information

Picture

There is no picture.

, Re-connect all connecting cords securely. , The connecting cords are damaged. , Check the connection to your TV (page 13). , Switch the input selector on your TV (such as to

“VCR”) so that the signal from the recorder appears on the TV screen.

, Check that “Scart Setting” in Video Setup is set

to the appropriate item that conforms to your system (page 83).

, If you connect the recorder to your TV via only

the COMPONENT VIDEO OUT jacks, set “Component Out” in Video Setup to “On” (page 83).

, This recorder cannot record NTSC signals. , A scrambled channel is selected.

Picture noise appears.

, If the picture output signal from your recorder

passes through your VCR to get to your TV, or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some DVD programmes could affect picture

TV channels cannot be changed.

, The Parental Lock is activated (page 78). , A timer recording started, which changed the

channels.

The picture from equipment connected to the recorder’s input jack does not appear on the screen.

, If the equipment is connected to the LINE 1-TV

jack, select “L1” in the front panel display by pressing PROG +/– or INPUT SELECT. If the equipment is connected to the LINE 2 IN jacks, select “L2” in the front panel display by pressing PROG +/– or INPUT SELECT. If the equipment is connected to the LINE 4 IN jacks, select “L4” in the front panel display by pressing PROG +/– or INPUT SELECT. If the equipment is connected to the LINE 3 jack, select “L3” in the front panel display by pressing PROG +/– or INPUT SELECT.

, When an S video cable is connected to the

recorder’s LINE 4 IN jack, set “Line4 Input” in Video Setup to “S Video” (page 84).

,continued

RDR-GXD500

2-188-393-11(1)

Page 92

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 92 Mardi, 7. septembre 2004 9:41 09

master page=left

The playback picture or TV programme from the equipment connected through the recorder is distorted.

, If the playback picture output from a DVD

player, VCR, or tuner goes through your recorder before reaching your TV, the copy-protection signal applied to some programmes could affect picture quality. Disconnect the playback equipment in question and connect it directly to your TV.

The picture does not fill the screen.

, Set “TV Type” in Video Setup in accordance

with the aspect ratio of your TV (page 82).

The picture does not fill the screen, even though the aspect ratio is set in “TV Type” in Video Setup.

, The aspect ratio of the disc is fixed on your DVD.

The picture is black and white.

, Check that “Line1 Output” of “Scart Setting” in

Video Setup is set to the appropriate item that conforms to your system (page 83).

, If you are using a SCART cord, be sure to use

one that is fully wired (21 pins).

Sound

There is no sound.

, Re-connect all connections securely. , The connecting cord is damaged. , The input source setting on the amplifier or the

connection to the amplifier is incorrect.

, The recorder is in reverse play, fast-forward,

slow motion, or pause mode.

, If the audio signal does not come through the

DIGITAL OUT (OPTICAL or COAXIAL) jacks, check the Audio Setup settings (page 84).

, A scrambled channel is selected.

Sound distortion occurs.

, Set “Audio ATT” in Audio Setup to “On”

(page 84).

The sound volume is low.

, The sound volume is low on some DVDs.

The sound volume may improve if you set “Audio DRC” in Audio Setup to “TV Mode” (page 85).

, Set “Audio ATT” in Audio Setup to “Off”

(page 84).

An alternate audio track cannot be recorded or played.

, When recording from connected equipment, set

“Line Audio Input” in TOOLS menu to “Bilingual” (page 57).

, If you have connected an AV amplifier to the

DIGITAL OUT (OPTICAL or COAXIAL) jack and want to change the audio track for a DVDRW (VR mode) during playback, set “Dolby Digital” in Audio Setup to “D-PCM” (page 85).

Sound break up

, Signal strength low. , Check aerial installation.

Playback

The disc does not play.

, The disc is upside down. Insert the disc with the

labelled side facing up.

, The disc is not correctly inserted. , Moisture has condensed inside the recorder.

Remove the disc and leave the recorder turned on for about half an hour until the moisture evaporates.

, If the disc was recorded on another recorder, the

recorder cannot play the disc if it was not finalized (page 34).

The disc does not start playback from the beginning.

, Resume play was activated (page 58). , You have inserted a disc whose Title menu or

DVD menu automatically appears on the TV screen when it is first inserted. Use the menu to start playback.

Sound is noisy.

, When playing a CD with DTS sound tracks,

noise will come from the LINE 2 OUT AUDIO L/R jacks, LINE 1-TV jack, or LINE 3 jack (page 62).

The recorder starts playing the disc automatically.

, The DVD VIDEO features an auto playback

function.

RDR-GXD500

2-188-393-11(1)

Page 93

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 93 Mardi, 7. septembre 2004 9:41 09

master page=right

Playback stops automatically.

, If the disc has an auto pause signal, the recorder

stops playback at the auto pause signal.

Some functions such as Stop, Search, or Slowmotion Play cannot be performed.

, Depending on the disc, you may not be able to do

some of the operations above. See the instruction manual supplied with the disc.

The language for the sound track cannot be changed.

, Multilingual tracks are not recorded on the disc

being played.

, The DVD VIDEO prohibits the changing of the

language for the sound track.

, Try changing the language using the DVD

VIDEO’s menu.

The subtitle language cannot be changed or turned off.

, Multilingual subtitles are not recorded on the

DVD VIDEO.

, The DVD VIDEO prohibits changing of the

subtitles.

, Try changing the subtitle using the DVD

VIDEO’s menu.

, The subtitles cannot be changed for the titles

recorded on this recorder.

The angles cannot be changed.

, Multi-angles are not recorded on the DVD

VIDEO being played.

, You are trying to change the angles when “ ”

does not appear on the TV screen (page 60).

, The DVD VIDEO prohibits changing angles. , Try changing the angle using the DVD VIDEO’s

menu.

, The angles cannot be changed for the titles

recorded on this recorder.

The MP3 audio tracks do not play.

, The MP3 audio tracks are not recorded in a

format that the recorder can play (page 66).

Recording/Timer recording/Editing

The programme position cannot be changed from the channel you are recording.

, Set the TV’s input source to “TV.”

Recording does not start immediately after you press z REC.

, Operate the recorder only after “LOAD”,

“FORMAT,” or “INFOWRITE” disappears from the front panel display.

Nothing was recorded even though you set the timer setting correctly.

, There was a power failure during recording. , The recorder’s internal clock stopped due to a

power failure that lasted for more than 1 hour. Reset the clock (page 77).

, Disconnect the mains lead from the mains, and

connect it again.

, The programme contains copy protection signals

that restrict copying.

, Other timer setting overlapped the timer setting

(page 52).

, There is no DVD inside the recorder. , There is not enough disc space for the recording. , A scrambled channel is selected. , The Channel activated Parental Lock is selected.

Recording does not stop immediately after you press x REC STOP.

, It will take a few seconds for the recorder to input

disc data before recording can stop.

Recording does not stop after you press x STOP.

, Open the remote’s cover and press x REC

STOP.

Timer recording is not complete or did not start from the beginning.

, There was a power failure during recording. If

the power recovers when there is a timer recording, the recorder resumes recording. Should the power failure continue for more than 1 hour, reset the clock (page 77).

, Other timer setting overlapped the timer setting

(page 52).

, Disc space was not enough.

Additional Information

,continued

RDR-GXD500

2-188-393-11(1)

Page 94

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 94 Mardi, 7. septembre 2004 9:41 09

master page=left

Contents previously recorded were erased.

, Data that has been recorded on a DVD with a PC

will be erased from the disc when the disc is inserted.

Recording from the equipment with a timer

Nothing was recorded even though you set the Synchro-Rec setting correctly.

, You forgot to turn off the connected equipment.

Turn off the connected equipment and set the recorder to Synchro-Rec standby mode (page 55).

, The recorder was not set to the Synchro-

Recording standby mode. Press SYNCHRO REC to have the recorder stand by for recording. Make sure the SYNCHRO REC indicator lights up on the front panel (page 55).

, The recorder is connected to the TV output jack

of the connected equipment.

Synchro-Recording does not complete.

, The timer setting for the connected equipment

overlapped the recorder’s timer setting (page 56).

, There was a power failure during the recording.

Display

The clock has stopped.

, Set the clock again (page 77). , The clock stopped due to a power failure that

lasted for more than 1 hour. Reset the clock (page 77).

The TIMER REC indicator is flashing.

, The disc does not have enough space. , Insert a recordable disc inside the recorder.

The recording mode indication is incorrect.

, When the recording is less than three minutes,

the recording mode indication may be displayed incorrectly. The actual recording itself is correctly made in the selected recording mode.

Remote control

The remote does not function.

, Batteries are weak. , The remote is too far from the recorder. , The remote’s manufacturer code returned to the

default setting when you replaced the batteries. Reset the code (page 20).

, Turn on the recorder. , The remote is not pointed at the remote sensor on

the recorder.

, Different command modes are set for the

recorder and remote. Set the same command mode (page 21).

, Set the TV/DVD switch to DVD (page 21).

Other Sony equipment responds to the remote.

, The same command mode is set for both the

equipment and recorder. Set a different command mode for the recorder (page 21).

Others

The recorder does not operate properly.

, Restart the recorder. Press down [/1 on the

recorder for more than ten seconds until “WELCOME” appears in the front panel display.

, When static electricity, etc., causes the recorder

to operate abnormally, turn off the recorder and wait until the clock appears in the front panel display. Then, unplug the recorder and after leaving it off for a while, plug it in again.

Five numbers or letters are displayed in the front panel display.

, The self-diagnosis function was activated (see

the table on page 95).

The disc tray does not open after you press Z (open/close).

, It may take a few seconds for the disc tray to

open after you have recorded or edited a disc. This is because the recorder is adding disc data to the disc.

The clock does not appear in the front panel display.

, “Dimmer” in Options Setup is set to “Power

Save” (page 89).

The disc tray does not open and “TRAY LOCKED” appears in the front panel display.

, Contact your Sony dealer or local authorized

Sony service facility.

RDR-GXD500

2-188-393-11(1)

Page 95

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 95 Mardi, 7. septembre 2004 9:41 09

master page=right

“RECOVERY” appears in the front panel display.

, The recorder’s recovery function was activated

when the recorder was turned on because the power was turned off or failed during recording. Leave the recorder on until “RECOVERY” disappears from the front panel display.

“FAN ERROR” appears in the front panel display.

, Check that the vent on the rear of the recorder is

not blocked. Then, turn off the recorder, wait until the clock appears in the front panel display, and disconnect the mains lead. Leave the recorder off for a while, then re-connect the mains lead, and press [/1 on the recorder.

The Parental Lock does not work.

, Check the Parental Lock options settings

(page 78).

Mechanical sound is heard when the recorder is off.

, While the recorder is updating the EPG

infomation, operational noises (such as the internal fan) may be heard, even when the power is off. This is not a malfunction.

The disc tray does not open and you cannot remove the disc after you press Z (open/ close).

, Turn off the recorder. Once the clock appears in

the front panel display, disconnect the mains lead. Connect it again while pressing down A on the recorder, and release the button when the disc tray opens. Then, keep [/ pressed for about ten seconds until “WELCOME” appears in the front panel display.

1 on the recorder

Self-diagnosis Function (When letters/numbers appear in the display)

When the self-diagnosis function is activated to prevent the recorder from malfunctioning, a fivecharacter service number (e.g., C 13 50) with a combination of a letter and four numbers appears in the front panel display. In this case, check the following table.

First three characters of the service number

C 13 The disc is dirty.

C 31 The disc is not inserted

E XX

(xx is a number)

Cause and/or corrective action

, Clean the disc with a

soft cloth.

correctly. , Re-insert the disc

correctly.

To prevent a malfunction, the recorder has performed the selfdiagnosis function. , Contact your nearest

Sony dealer or local authorized Sony service facility and give the fivecharacter service number. Example: E 61 10

Additional Information

“LOCKED” appears in the front panel display.

, The disc tray is locked. Cancel the Child Lock

(page 59).

RDR-GXD500

2-188-393-11(1)

Page 96

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 96 Mardi, 7. septembre 2004 9:41 09

Notes About This Recorder

On operation

• If the recorder is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the recorder. Should this occur, the recorder may not operate properly. In this case, remove the disc and leave the recorder turned on for about half an hour until the moisture evaporates.

• When you move the recorder, take out any discs. If you do not, the disc may be damaged.

On adjusting volume

Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

master page=left

• After playing, store the disc in its case.

• Clean the disc with a cleaning cloth. Wipe the disc from the centre out.

• Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs.

• Do not use the following discs. – A disc that has a non-standard shape (e.g.,

card, heart). – A disc with a label or sticker on it. – A disc that has cellophane tape or sticker

adhesive on it.

On cleaning discs

Do not use a commercially available cleaning disc. It may cause a malfunction.

Notes about the discs

• To keep the disc clean, handle the disc by its edge. Do not touch the surface. Dust, fingerprints, or scratches on the disc may cause it to malfunction.

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

RDR-GXD500

2-188-393-11(1)

Page 97

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 97 Mardi, 7. septembre 2004 9:41 09

Specifications

System

Laser: Semiconductor laser Transmission standards: DVB-T Channel coverage:

UHF channels B21 - B69

Aerial out: 75-ohm asymmetrical aerial socket Video recording format: MPEG Video Audio recording format/applicable bit rate:

Dolby Digital/2 ch, 256 kbps

When you play PCM sound tracks with a 96 kHz sampling frequency, the output signals from the DIGITAL OUT (OPTICAL or COAXIAL) jack are converted to 48 kHz sampling frequency.

Inputs and outputs

LINE 2 OUT (AUDIO): Phono jack/2 Vrms/10 kilohms (VIDEO): Phono jack/1.0 Vp-p (S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p, C: 0.3

Vp-p (PAL)

LINE 2 IN/LINE 4 IN (AUDIO): Phono jack/2 Vrms/more than 22

kilohms

(VIDEO): Phono jack/1.0 Vp-p (S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p, C: 0.3

Vp-p (PAL)

master page=right

LINE 1 -TV: 21-pin

CVBS IN/OUT S-Video/RGB OUT (upstream)

LINE 3: 21-pin

CVBS IN/OUT S-Video/RGB IN S-Video OUT (downstream) Decoder

DIGITAL OUT (OPTICAL): Optical output

jack/–18 dBm (wave length: 660 nm)

DIGITAL OUT (COAXIAL): Phono jack/0.5

Vp-p/75 ohms

COMPONENT VIDEO OUT

(Y, P

B/CB, PR/CR):

Phono jack/Y: 1.0 Vp-p, P

R/CR: 0.7 Vp-p

B/CB: 0.7 Vp-p,

General

Power requirements: 220-240 V AC, 50/60 Hz Power consumption: 41W Dimensions (approx.): 430 × 85 × 346 mm

(width/height/depth) incl. projecting parts

Mass (approx.): 4.9 kg Operating temperature: 5 ºC to 35 ºC Operating humidity: 25 % to 80 % Supplied accessories:

Audio/video cord (1) Mains lead (1) Aerial cable (1) Remote commander (remote) (1) R6 (size AA) batteries (2)

Additional Information

Specifications and design are subject to change without notice.

Compatible colour systems

This recorder is designed to record using the PAL colour system and play back using the PAL or NTSC colour systems.

RDR-GXD500

2-188-393-11(1)

Page 98

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 98 Mardi, 7. septembre 2004 9:41 09

master page=left

Guide to Parts and Controls

For more information, see the pages in parentheses.

Front panel

Buttons on the recorder have the same function as the buttons on the remote if they have the same or similar names.

A @/1 (on/standby) button (22) B Front panel display (36, 100) C Disc tray (46) D TIMER REC indicator (46)

SYNCHRO REC indicator (55)

E (remote sensor) (19) F A (open/close) button (46) G H (play) button (58)

X (pause) button (60) x (stop) button (58)

H z REC button (52)

X REC PAUSE button (52) x REC STOP button (52)

I </M/m/,/ENTER button (22) J SYSTEM MENU button (29)

TOOLS button (30)

K O RETURN button (30) L ./> (previous/next) buttons (60) M PROGRAM +/– buttons (52) N INPUT SELECT button (57) O REC MODE button (45) P LINE 2 IN (S VIDEO/VIDEO/AUDIO L/

R) jacks (27)

RDR-GXD500

2-188-393-11(1)

Page 99

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 99 Mardi, 7. septembre 2004 9:41 09

Remote

Buttons on the remote have the same function as the buttons on the recorder if they have the same or similar names. Buttons with an orange dot next to them can be used with your TV when the TV/ DVD switch is set to TV.

1 2 3

4 5 6

7 8 9

master page=right

A TV/DVD switch (20) B Z (open/close) button (46, 60) C Number buttons (37, 65)*

SET button (37) The number 5 button has a tactile dot.

D CLEAR/-/-- (ten digit) button (37) E (audio) button (60)

(subtitle) button (60)

F EPG button (38, 48)

Favourite button (43) INFO button (40) Text button (42)

G SYSTEM MENU button (29)

TITLE LIST button (30, 58, 69) TOOLS button

(30)

H CURSOR MODE button (30) I O RETURN button (30) J TOP MENU button (58) K . (previous)/> (next)

buttons (60)

L z REC button (52)

X REC PAUSE button (52) x REC STOP button (52)

M REC MODE button (45) N (angle) button (60) O SUR (surround) button (60) P SYNCHRO REC button (55) Q [TIMER] button (46) R [/1 (on/standby) button (22) S PROG (programme) +/– buttons* (52)

The + button has a tactile dot.

T 2 (volume) +/– buttons (20) U t (TV/video), TV/DVD button (20) V TV/Radio button (42) W Coloured multimedia applications &

interactive services control buttons (38)

X </M/m/,/ENTER button (22) Y ZOOM +/– buttons (30)

Additional Information

,continued

RDR-GXD500

2-188-393-11(1)

Page 100

D:\DVD

manual\Final\218839311_FM\01GB11ADD.fm

01GB01.book Page 100 Mardi, 7. septembre 2004 9:41 09

master page=left

Z (instant replay)/ (instant advance)

buttons (60)

wj MENU button (58) wk m / M (search) buttons (60) wl H (play) button* (58)

The button has a tactile dot.

X (pause) button x (stop) button (58)

(60)

Front panel display

DVD RW VCDVR

SMARTLINK

A Playing/recording status B Disc type*/recording format C (angle) indicator (60) D PLAYLIST indicator (31) E Audio signal indicators (35) F STEREO/BILINGUAL indicators (55) G TV indicator (52)

e; CHAPTER MARK/ERASE buttons (72) ea INPUT SELECT button (57) es DISPLAY button

(35)

TIME/TEXT button (35)

ed COMMAND MODE switch (DVD 1,2,3)

(21)

* Use the tactile dot as a reference when operating the

recorder.

PLAYLIST

STEREO

BILINGUAL

H Displays the following (36):

• Playing time/remaining time

• Current title/chapter/track/index number

• Recording time/recording mode

•Clock

• Programme position

• TV Direct Rec indication appears in the right most two digits.

(52): “TV”

I SMARTLINK indicator (15)

* Displays DATA CDs as “CD.”

z Hint

You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Power Save” in Options Setup (page 89).

100

2-188-393-11(1)

RDR-GXD500

Sony RDR-GXD500 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual