Sony POWER TRILOGIC SLV-L72HF PA-PC, POWER TRILOGIC SLV-L49 MX, POWER TRILOGIC SLV-L69HF MX, POWER TRILOGIC SLV-L79HF CL-CS-VZ, POWER TRILOGIC SLV-L52 PA-PC User Manual
...
3-865-427-12(1)
Video Cassette
Recorder
Operating Instructions
SLV-L49 MX
SLV-L52 PA/PC
SLV-L59 CL/CS/PR/VZ
SLV-X55 MX
SLV-L69HF MX
SLV-L72HF PA/PC
SLV-L79HF CL/CS/VZ
SLV-L89HF CL/CS/MX/VZ
SLV-X66HF MX
©1999 by Sony Corporation
WARNING
To prevent fire or shock hazard, do
not expose the unit to rain or
moisture.
The power cord must be changed only at a
qualified service shop.
Precautions
Safety
• For SLV-L59 CL/CS/PR, L79HF CL/CS
and L89HF CL/CS, operate the unit on 110
to 240 V AC, 50/60 Hz. For SLV-L49 MX,
L52 PA/PC, L59 VZ, X55 MX, L69HF MX,
L72HF PA/PC, L79HF VZ, L89HF MX/VZ
and X66HF MX, operate the unit only on
120 V AC, 60 Hz.
• If anything falls into the cabinet, unplug
the unit and have it checked by qualified
personnel before operating it any further.
• This unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
unit itself has been turned off.
• Unplug the unit from the wall outlet if you
do not intend to use it for an extended
period of time. To disconnect the cord, pull
it out by the plug, never by the cord.
Installing
• Allow adequate air circulation to prevent
internal heat buildup.
• Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation
slots.
• Do not install the unit near heat sources
such as radiators or air ducts, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration or shock.
• Do not install the unit in an inclined
position. It is designed to be operated in a
horizontal position only.
• Keep the unit and cassettes away from
equipment with strong magnets, such as
microwave ovens or large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to
a warm location, moisture may condense
inside the VCR and cause damage to the
video head and tape. When you first install
the unit, or when you move it from a cold
to a warm location, wait for about three
hours before operating the unit.
Caution
Television programs, films, video tapes and
other materials may be copyrighted.
Unauthorized recording of such material may
be contrary to the provisions of the copyright
laws. Also, use of this recorder with cable
television transmission may require
authorization from the cable television
transmission and/or program owner.
Information
“Power Trilogic” is a trademark of Sony
Corporation.
2 Getting Started
Table of contents
Getting Started
4 Step 1: Unpacking
5 Step 2: Setting up the remote commander
7 Step 3: Hookups
24 Selecting a language
25 Setting the clock
31 Presetting channels
Getting Started
Basic Operations
38 Playing a tape
41 Recording TV programs
44 Recording TV programs using the
timer
Additional Operations
48 Playing/searching at various
speeds
51 Searching for a selected point on
the tape
53 Skip-searching automatically
54 Recording TV programs using the
dial timer
57 Setting the recording duration
time
58 Checking/changing/canceling
timer settings
60 Recording stereo and bilingual
programs (SLV-L69HF MX,
L72HF PA/PC, L79HF CL/CS/
VZ, L89HF CL/CS/MX/VZ and
X66HF MX only)
62 Adjusting the picture
64 Changing menu options
65 Editing with another VCR
Additional Information
67 General setup information
69 Troubleshooting
71 Specifications
72 Index to parts and controls
79 Index
back cover
Quick reference to using the VCR
3Introduction
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• Size AA (R6) batteries
• Audio/video cable (3-phono to 3-
phono) (SLV-L69HF MX, L72HF PA/
PC, L79HF CL/CS/VZ, L89HF CL/
CS/MX/VZ and X66HF MX only)
• 75-ohm coaxial cable with F-type
connectors
• Plug adaptor (SLV-L59 CL/CS/PR,
L79HF CL/CS and L89HF CL/CS
only)
If the plug supplied with your VCR does not
fit your power outlet, attach the supplied
adaptor to the plug.
Checking your model name
The instructions in this manual are for the 19 models: SLV-L49 MX,
L52 PA/PC, L59 CL/CS/PR/VZ, X55 MX, L69HF MX, L72HF PA/PC,
L79HF CL/CS/VZ, L89HF CL/CS/MX/VZ and X66HF MX. Check
your model number by looking at the rear panel of your VCR. The SLVL89HF MX is the model used for illustration purposes. Any difference in
operation is clearly indicated in the text, for example, “SLV-X66HF MX
only”.
4 Getting Started
Step 2
1/u
§
0
)
1/u
Setting up the remote commander
Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with
a dot (•) can be used to operate
your Sony TV.
TV / VIDEO
Remote sensor
Getting Started
To operate Set TV / VIDEO to
the VCR VIDEO and point at the remote sensor on the VCR
a Sony TV TV and point at the remote sensor on the TV
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
continued
5Getting Started
Step 2: Setting up the remote commander (continued)
Controlling other TVs with the remote commander
(SLV-L69HF MX, L72HF PA/PC, L79HF CL/CS/VZ, L89HF
CL/CS/MX/VZ and X66HF MX only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the table below, set the appropriate manufacturer’s code
number.
1 Set TV / VIDEO at the top of the remote commander to TV .
2 Hold down 1/u, and enter your TV’s code number(s) using the number
buttons. Then release 1/u .
Now you can use the 1/u , VOL +/–, CH +/– and TV/VIDEO buttons to
control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the VCR, reset TV / VIDEO to VIDEO .
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
Manufacturer
Sony
Akai
AOC
Centurion
Coronado
Curis-Mathes
Daytron
Emerson
Fisher
General Electric
Gold Star
Hitachi
J.C.Penny
Notes
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
• When you press the AUDIO MONITOR button, your TV’s menu may appear on the
TV screen. To exit the TV menu, press the MENU button on the TV remote
commander or wait until the menu disappears automatically.
Code
number
01
04
04
12
03
12
12
03, 04, 14
11
06, 10
03, 04, 17
02, 03
04, 12
Manufacturer
JVC
KMC
Magnavox
Marantz
MGA/Mitsubishi
NEC
Panasonic
Philco
Philips
Pioneer
Portland
Quasar
Radio Shack
Code
number
09
03
03, 08, 12
04, 13
04, 12, 13, 17
04, 12
06, 19
03, 04
08
16
03
06, 18
05, 14
Manufacturer
RCA
Sampo
Sanyo
Scott
Sears
Sharp
Sylvania
Teknika
Toshiba
Wa r d s
Yorx
Zenith
Code
number
04, 10
12
11
12
07, 10, 11
03, 05, 18
08, 12
03, 08, 14
07
03, 04, 12
12
15
6 Getting Started
Step 3
Hookups
Selecting the best hookup option
There are many ways in which your VCR can be hooked up. To hook up
your VCR so that it works best for you, first scan through the table below.
Then use the accompanying diagrams and procedures on the following
pages to set up your VCR.
If you have Use Refer to
TV that has audio/video input Audio/video (A/V) hookup, then Pages 8 to 10
follow one of the hookups below.
Antenna only, no cable TV Hookup 1 Pages 11 to 13
No cable box, or cable box with only Hookup 2 Pages 14 to 16
a few scrambled channels
Cable box, with many scrambled Hookup 3 Pages 17 to 19
channels
Cable box with only a few scrambled Hookup 4 Pages 20 to 23
channels, using an A/B switch
After you’ve completed the connections, follow the instructions for setup.
During setup, if you need more details on the procedure described, page
numbers are provided where you can find complete, step-by-step
instructions.
After you’ve completed the setup, you’re ready to use your VCR.
Procedures differ depending on the hookup you used. For an overview,
refer to “Quick reference to using the VCR” on the back cover.
Getting Started
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are
completed.
• Be sure you make connections firmly. Loose connections may cause
picture distortion.
• If your TV doesn’t match any of the examples provided, see your nearest
Sony dealer or qualified technician.
continued
7Getting Started
Step 3: Hookups (continued)
Audio/video (A/V) hookup Pages 8 to 10
If your TV has audio/video (A/V) input jacks, you will get a better picture
and sound when you hook up your VCR using these connections. If your
TV doesn’t have A/V inputs, see the following pages for antenna or cable
hookups.
If you’re not planning to use your VCR to record programs, you’re finished
setting up the VCR after you’ve made the connections shown on pages 8 and
9.
If you want to record off-air or off your cable TV system, complete these
connections first, and then go to the following pages for antenna or cable
hookups.
For SLV-L49 MX, L52 PA/PC, L59 CL/CS/PR/VZ and X55 MX
A Use this hookup if your TV has stereo jacks
VCR
LINE-1 IN
LINE OUT
AUDIO VIDEO
TV
IN
VIDEO
AUDIO
B Use this hookup if your TV doesn’t have stereo jacks
Note
• If you use the Trinitron TV Synchro Play function (see page 40), the A/V connection
is necessary. (If your TV has two or more inputs, connect the audio/video cable to
the VIDEO IN 1 jacks.)
8 Getting Started
Audio/video cable (not supplied)
VCR
AUDIO VIDEO
LINE-1 IN
LINE OUT
Audio/video cable (not supplied)
TV
IN
VIDEO
AUDIO
For SLV-L69HF MX, L72HF PA/PC, L79HF CL/CS/VZ, L89HF CL/CS/MX/VZ
and X66HF MX
For a true “home theater” experience, you should connect the audio outputs
of your VCR or TV to your stereo system.
A Use this hookup if your TV has stereo jacks
VCR Stereo receiver
AUDIO VIDEO
LINE-1 IN
LINE OUT
Audio/video cable (supplied)
TV
IN
VIDEO
AUDIO
AUDIO OUT
Audio cable (not supplied)
B Use this hookup if your TV doesn’t have stereo jacks
VCR
AUDIO VIDEO
LINE-1 IN
LINE OUT
Video Cable (not supplied) Audio cable (not supplied)
TV
IN
VIDEO
AUDIO
Getting Started
AUX IN
Stereo receiver
AUX IN
Notes
• To play a tape in stereo, you must use the A/V connection.
• If you use the Trinitron TV Synchro Play function (see page 40), the A/V connection
is necessary. (If your TV has two or more inputs, connect the audio/video cable to
the VIDEO IN 1 jacks.)
continued
9Getting Started
Step 3: Hookups (continued)
A/V hookup: VCR setup
After you’ve connected your TV and completed antenna or cable hookup,
use the following procedure to set up the VCR.
Press MENU and select
ADVANCED OPTIONS.
TIMER SET/CHECK
SETTINGS
ADVANCED OPTIONS
n
:
SELECT
n
:
O K
SET
:
MENU
QUIT
/
Set AUTO ANT SELECT
to OFF and press OK.
ADVANCED OPTIONS
AUTO ANT SELECT
AUTO STEREO
TUNER AUDIO
APC
TAPE SELECT
AUTO TAPE SPEED
SHARPNESS
NRETURN
n
:
SELECT
n
:
O K
SET
:
MENU
QUIT
ON
OFF
ON
AUTO
ON
L H
For details, see page 64.
10 Getting Started
Hookup 1 Pages 11 to 13
Antenna hookup
Make the following connections if you’re using an antenna (if you don’t
have cable TV).
A Use this hookup if you’re using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
Rear of TV
VHF/UHF
VCR
VHF/UHF
IN
OUT
or
or
VHF
UHF
VHF
UHF
B Use this hookup if you’re using a VHF-only antenna (you get
channels 2–13 only)
VCR
VHF/UHF
IN
OUT
or
or
Rear of TV
VHF/UHF
VHF
UHF
VHF
Match the type of
A
connector on your
TV: A, B, or C.
B
C
A
Match the type of
connector on your
TV: A, B, or C.
B
For connector types
B and C, no UHF
connection is
required.
C
Getting Started
UHF
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN
connector. If you have separate cables for VHF and UHF antennas, you should use a
U/V band mixer (not supplied). For details, see page 68.
continued
11Getting Started
Step 3: Hookups (continued)
SET UP
CLOCK SET
AUTO
MANUAL
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
SELECCIONAR
SIGUIENTE
CANCELAR
:
:
:
AJUSTE
IDIOMA
O K
EASY SET UP
n
n
ENGLISH
ESPA
OL
Hookup 1: VCR setup
1 Set the RF UNIT switch to
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set the
switch to either channel.
For details, see page 67. If
you made A/V connections
(from page 8), you can skip
this step.
2 Press EASY SET UP on the
VCR.
1 The IDIOMA menu appears. Change the on-
screen display language to English (ENGLISH)
if desired, and press OK. For details, see page
24.
2 The CLOCK SET menu appears. Select
MANUAL and press OK. Then set the clock.
For details, see page 29.
RF UNIT
CH3
CH4
)
0
EASY SET UP
12 Getting Started
3 The TUNER PRESET menu appears. Set
ANTENNA/CABLE to ANT and press OK. For
details, see page 31.
4 The AUTO PRESET starts.
SET UP
TUNER PRESET
AUTO PRESET
PROCESSING
PLEASE WAIT
ANTENNA / CABLE
SELECT
NEXT
CANCEL
/
SET UP
TUNER PRESET
n
:
n
:
O K
:
EASY SET UP
SET UP
SET UP IS DONE
.
Normal display
continued
ANT
CABLE
Getting Started
13Getting Started
Step 3: Hookups (continued)
Hookup 2 Pages 14 to 16
No cable box, or cable box with only a few
scrambled channels
Recommended use
Use this hookup if you do not have a cable box. Also use this hookup if your
cable system scrambles only a few channels.
What you can do with this hookup
• Record any unscrambled channel by selecting the channel on the VCR
What you can’t do
• Record scrambled channels that require a cable box
Wall
Connect this cable
directly to your TV
if you don't have a
cable box.
Cable box
IN
OUT
VCR
VHF/UHF
IN
OUT
Rear of TV
VHF/UHF
or
or
A Match the type
of connector
on your TV: A,
B, or C.
VHF
B
For connector
types B and C, no
UHF connection
UHF
is required.
VHF
C
UHF
14 Getting Started
Hookup 2: VCR setup
SET UP
CLOCK SET
AUTO
MANUAL
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
SELECCIONAR
SIGUIENTE
CANCELAR
:
:
:
AJUSTE
IDIOMA
O K
EASY SET UP
n
n
ENGLISH
ESPA
OL
SET UP
COUNTRY / TIME ZONE
BELIZE
BOLIVIA
CHILE
COLOMBIA
COSTA RICA
CUBA
DOMIN. REP.
ECUADOR
EL SALVADR
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
1 Set the RF UNIT switch to
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 67. If
you made A/V connections
(from page 8), you can skip
this step.
2 Press EASY SET UP on the VCR.
1 The IDIOMA menu appears. Change the on-
screen display language to English (ENGLISH)
if desired, and press OK. For details, see page
24.
2 The CLOCK SET menu appears. Select AUTO
and press OK. For details, see page 25.
RF UNIT
CH3
CH4
)
0
EASY SET UP
Getting Started
3 The COUNTRY/TIME ZONE menu appears.
Select the country you want to set and press OK.
You can select following countries:
BELIZE ˜ BOLIVIA ˜ CHILE ˜
COLOMBIA ˜ COSTA RICA ˜ CUBA ˜
DOMIN. REP. ˜ ECUADOR ˜
EL SALVADR ˜ GUATEMALA ˜
GUYANA ˜ HONDURAS ˜ JAMAICA ˜
MEX-CENT. ˜ MEX-MOUNT. ˜
MEX-PACIF. ˜ MEX-S. EAST ˜
NICARAGUA ˜ PANAMA ˜ PERU ˜
SURINAME ˜ TRIN. & TOB. ˜
VENEZUELA
continued
15Getting Started
Step 3: Hookups (continued)
4 The TUNER PRESET menu appears. Set
ANTENNA/CABLE to CABLE and press OK.
For details, see page 31.
SET UP
TUNER PRESET
ANTENNA / CABLE
n
:
SELECT
n
:
O K
NEXT
:
EASY SET UP
CANCEL
ANT
CABLE
5 The AUTO PRESET starts.
SET UP
TUNER PRESET
AUTO PRESET
PROCESSING
SET UP
SET UP IS DONE
/
PLEASE WAIT
.
Normal display
Automatic clock setting
Once you’ve set up the VCR, it automatically sets the clock the first time you
turn off the VCR. After that, whenever you turn off the VCR, it checks the
time and adjusts the clock, even for Daylight Saving Time. The VCR sets the
clock by picking up time signals provided by Sony Entertainment Television
(SETV).
If you want to use the timer to record right away, or if the cable TV station in
your area does not broadcast SETV, or if SETV in your area does not carry
time signals, set the clock manually. For details, see page 29.
Note
• The Daylight Saving Time start and end days may differ depending on the year. To
ensure correct switching, select ON or OFF for the DAYLIGHT SAVING setting
(page 28).
16 Getting Started
Hookup 3 Pages 17 to 19
Cable box with many scrambled channels
Recommended use
Use this hookup if your cable system scrambles all or most channels.
What you can do with this hookup
• Record any channel by selecting the channel on the cable box
What you can’t do
• Record with the cable box turned off
• Record one channel while watching another channel
Getting Started
Wall
VCR
VHF/UHF
IN
Cable box
IN
OUT
OUT
or
or
Rear of TV
VHF/UHF
A
VHF
UHF
VHF
UHF
Match the type
of connector on
your TV: A, B, or
C.
B For connector
types B and C, no
UHF connection
is required.
C
continued
17Getting Started
Step 3: Hookups (continued)
SET UP
CLOCK SET
AUTO
MANUAL
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
SELECCIONAR
SIGUIENTE
CANCELAR
:
:
:
AJUSTE
IDIOMA
O K
EASY SET UP
n
n
ENGLISH
ESPA
OL
SET UP
COUNTRY / TIME ZONE
BELIZE
BOLIVIA
CHILE
COLOMBIA
COSTA RICA
CUBA
DOMIN. REP.
ECUADOR
EL SALVADR
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
Hookup 3: VCR setup
1 Set the RF UNIT switch to
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set the
switch to either channel.
For details, see page 67. If
you made A/V connections
(from page 8), you can skip
this step.
2 Turn on your cable box.
3 Press EASY SET UP on the VCR.
1 The IDIOMA menu appears. Change the on-
screen display language to English (ENGLISH)
if desired, and press OK. For details, see page
24.
2 The CLOCK SET menu appears. Select AUTO
and press OK. For details, see page 25.
RF UNIT
CH3
CH4
)
0
EASY SET UP
18 Getting Started
3 The COUNTRY/TIME ZONE menu appears.
Select the country you want to set and press OK.
You can select following countries:
BELIZE ˜ BOLIVIA ˜ CHILE ˜
COLOMBIA ˜ COSTA RICA ˜ CUBA ˜
DOMIN. REP. ˜ ECUADOR ˜
EL SALVADR ˜ GUATEMALA ˜
GUYANA ˜ HONDURAS ˜ JAMAICA ˜
MEX-CENT. ˜ MEX-MOUNT. ˜
MEX-PACIF. ˜ MEX-S. EAST ˜
NICARAGUA ˜ PANAMA ˜ PERU ˜
SURINAME ˜ TRIN. & TOB. ˜
VENEZUELA
4 The TUNER PRESET menu appears. Set
ANTENNA/CABLE to ANT and press OK. For
details, see page 31.
SET UP
TUNER PRESET
ANTENNA / CABLE
n
:
SELECT
n
:
O K
NEXT
:
EASY SET UP
CANCEL
ANT
CABLE
5 The AUTO PRESET starts.
SET UP
TUNER PRESET
AUTO PRESET
PROCESSING
SET UP
SET UP IS DONE
/
PLEASE WAIT
.
Automatic clock setting
To use the Auto Clock Set feature with this hookup, you need to manually
select Sony Entertainment Television (SETV).
Normal display
1 Tune the cable box to SETV.
2 Select AUTO in the CLOCK SET menu to turn on the Auto Clock Set
feature.
3 Turn off the VCR. It automatically sets the clock and adjusts for
Daylight Saving Time by picking up the time signal.
If you want to use the timer to record right away, or if the cable TV station in
your area does not broadcast SETV, or if SETV in your area does not carry
time signals, set the clock manually. For details, see page 29.
Notes
• To use the Auto Clock Set feature, leave the cable box on.
• The Daylight Saving Time start and end days may differ depending on the year. To
ensure correct switching, select ON or OFF for the DAYLIGHT SAVING setting
(page 28).
continued
Getting Started
19Getting Started
Step 3: Hookups (continued)
Hookup 4 Pages 20 to 23
Cable box with only a few scrambled channels, using
an A/B switch
Recommended use
By using an A/B switch (not supplied), this hookup allows you to record
both scrambled and unscrambled channels conveniently.
What you can do with this hookup
• Record any unscrambled channel by selecting the channel directly on the
VCR (the A/B switch is set to “A”)
• Record any scrambled channel by selecting the channel on the cable box
(the A/B switch is set to “B”)
What you can’t do
• Record one scrambled channel while watching another channel (the A/B
switch is set to “B”)
Wall
Splitter
A/B switch
VCR
A
VHF/UHF
Cable box
IN
OUT
B
IN
OUT
Rear of TV
VHF/UHF
or
or
VHF
UHF
VHF
UHF
A
Match the type
of connector
on your TV: A,
B, or C.
B
For connector
types B and C,
no UHF
connection is
required.
C
20 Getting Started
Hookup 4: VCR setup
SET UP
CLOCK SET
AUTO
MANUAL
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
SELECCIONAR
SIGUIENTE
CANCELAR
:
:
:
AJUSTE
IDIOMA
O K
EASY SET UP
n
n
ENGLISH
ESPA
OL
SET UP
COUNTRY / TIME ZONE
BELIZE
BOLIVIA
CHILE
COLOMBIA
COSTA RICA
CUBA
DOMIN. REP.
ECUADOR
EL SALVADR
SELECT
NEXT
CANCEL
:
:
:
O K
EASY SET UP
n
n
1 Set the RF UNIT switch to
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set the
switch to either channel.
For details, see page 67. If
you made A/V connections
(from page 8), you can skip
this step.
2 Set the A/B switch to “A.”
3 Press EASY SET UP on the VCR.
1 The IDIOMA menu appears. Change the on-
screen display language to English (ENGLISH)
if desired, and press OK. For details, see page
24.
2 The CLOCK SET menu appears. Select AUTO
and press OK. For details, see page 25.
RF UNIT
CH3
CH4
)
0
EASY SET UP
Getting Started
3 The COUNTRY/TIME ZONE menu appears.
Select the country you want to set and press OK.
You can select following countries:
BELIZE ˜ BOLIVIA ˜ CHILE ˜
COLOMBIA ˜ COSTA RICA ˜ CUBA ˜
DOMIN. REP. ˜ ECUADOR ˜
EL SALVADR ˜ GUATEMALA ˜
GUYANA ˜ HONDURAS ˜ JAMAICA ˜
MEX-CENT. ˜ MEX-MOUNT. ˜
MEX-PACIF. ˜ MEX-S. EAST ˜
NICARAGUA ˜ PANAMA ˜ PERU ˜
SURINAME ˜ TRIN. & TOB. ˜
VENEZUELA
continued
21Getting Started
Step 3: Hookups (continued)
NRETURN
ANTENNA / CABLE
AUTO PRESET
AFT
FINE TUNING
MANUAL SET
CABLE
ADD
ERASE
SELECT
SET
QUIT
:
:
:
TUNER PRESET
CH123
O K
MENU
n
n
NRETURN
TUNER PRESET
CLOCK SET
LANGUAGE
SELECT
SET
QUIT
:
:
:
SETTINGS
O K
MENU
n
n
4 The TUNER PRESET menu appears. Set
ANTENNA/CABLE to CABLE and press OK.
For details, see page 31.
SET UP
TUNER PRESET
ANTENNA / CABLE
n
:
SELECT
n
:
O K
NEXT
:
EASY SET UP
CANCEL
5 The AUTO PRESET starts.
SET UP
TUNER PRESET
AUTO PRESET
PROCESSING
SET UP
SET UP IS DONE
/
PLEASE WAIT
.
Normal display
4 Preset the cable box output channel (usually 2, 3 or 4). For details,
see page 34.
1 Press MENU, then select SETTINGS and press
OK.
2 Select TUNER PRESET and press OK.
ANT
CABLE
22 Getting Started
3 Enter the cable box output channel.
4 Set MANUAL SET to ADD and press OK.
5 Press MENU to exit the menu.
Cable box output channel
Automatic clock setting
Once you’ve set up the VCR, it automatically sets the clock the first time you
turn off the VCR. After that, whenever you turn off the VCR, it checks the
time and adjusts the clock, even for Daylight Saving Time. The VCR sets the
clock by picking up time signals provided by Sony Entertainment Television
(SETV).
If you want to use the timer to record right away, or if the cable TV station in
your area does not broadcast SETV, or if SETV in your area does not carry
time signals, set the clock manually. For details, see page 29.
Notes
• To use the Auto Clock Set feature, set the A/B switch to “A”.
• The Daylight Saving Time start and end days may differ depending on the year. To
ensure correct switching, select ON or OFF for the DAYLIGHT SAVING setting
(page 28).
Getting Started
23Getting Started
Selecting a
SELECCIONAR
AJUSTAR
PARA SALIR
:
:
:
SELECCION DEL IDIOMA
O K
MENU
n
n
ENGLISH
ESPA
OL
language
You can change the on-screen display
language.
MENU
>/.
OK
MENU
1 Press MENU, then press >/. to highlight
AJUSTES and press OK.
When using the EASY SET UP procedure,
PLAY
OK
skip steps 1 and 2.
AJUSTES
PREAJUSTE DEL SINTONIZADOR
AJUSTE DEL RELOJ
SELECCION DEL IDIOMA
NVOLVER
SELECCIONAR
AJUSTAR
PARA SALIR
2 Press >/. to highlight SELECCION DEL
PLAY
OK
IDIOMA, then press OK.
3 Press >/. to highlight ENGLISH or ESPAÑOL, then press OK.
PLAY
OK
MENU
4 Press MENU to exit the menu.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
:
:
:
n
O K
MENU
n
24 Getting Started
Loading...