Page 1
INSTALLATION INSTRUCTIONS
Universal Pitch-Adjustable Wall Mount
For Flat Panel Display PLP-91/D
Your new Wall Mount (PLP-91/D) is a quick disconnect
Secures Display
mounting system with adjustability between 0 and
15 degrees pitch. The optional lateral shift bracket
(PAC-125) allows 4” lateral shift on either side of a 16”
center stud or spans a 24” on center stud system.
Once the Universal Flat Panel Display Wall Mount
Bracket is attached to your display, simply attach the
mount securely on a wall, lock the display in place using
the convenient Q-latch, and attach your audio/video
cables.
The PLP-91/D is virtually invisible when your display is
mounted.
Can Be Used to
Lock Display
BEFORE YOU BEGIN
• Caution: To prevent damage to the PLP-91/D, which could affect or void the Factory warranty, and to the equipment
that will be attached to it, thor oughly study al l instructi ons and illust rations befor e you begin the installation . Pay particular attention to the “Important Warnings and Precautions” on Page 1.
• The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the mount must
be capable of supporting five times the total weight of the equipment.
• The maximum weight to be installed on the Universal Pitch-Adjustable Wall Mount is 125 pounds (56.7 Kg).
Sony Electronics Inc. 8805-000087
1 Sony Drive
Park Ridge, NJ 07656
201-930-1000
www.sony.com/displaysystems
Page 2
Installation Instructions Pitch-Adjustable Mount PLP91/D
IMPORTANT WARNINGS AND PRECAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-
sponding instructions.
• WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can
support a weight factor five times the total weight of the equipment. If not, reinforce the structure before
installing the mount.
• WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
• WARNING:The installer is responsible for verifying that the wall to which the mount is anchored will safely support
the combined load of all attached components or other equipment.
• WARNING:Watch for pinch points. Do not put your fingers between movable parts.
• WARNING:Make sure the mount and brackets are correctly oriented.
• WARNING:Make sure the latching flag securing the display is completely engaged at all times except when removing
or installing the display. The latching flag must be all completely engaged when installing/removing
cables.
• CAUTION: Check the unit for shipping damage before you begin the installation.
• CAUTION: Use only the mounting screws provided and DO NOT OVER TIGHTEN mou nting screws.
CONTENTS
DIMENSIONAL DRAWING .............................. 2
INSTALL MOUNT.............................................. 3
INSTALL DISPLAY BRACKETS...................... 3
MOUNT THE DISPLAY..................................... 3
PARTS ................................................................. 4
TOOLS REQUIRED FOR INSTALLATION
• Phillips screwdrivers, No. 1 and No. 2 TIP
• Drill and bit set
• Wrench set
NOTE: Other tools may be required depending on the
method of installation.
1
Page 3
Installation Instructions Pitch-Adjustable Mount PLP91/D
INTERFACE BRACKETS ADD APPROXIMATELY 1/2" TO DEPTH
11/16"
15 3/4"
1 9/16"
2"
5/16"
16"
10 1/2"
8"
1 5/16"
17"
Tighten this screw
to lock tilt in place
1 1/2"
DIMENSIONAL DRAWING
2
Page 4
Installation Instructions Pitch-Adjustable Mount PLP91/D
INSTALL MOUNT
Install the mount as follows:
1. Determine the exact mounting location prior to installation and
draw a level line to indicate the desired height for the top of the
mounting plate.
WARNING: Improper installation can result in serious per-
sonal injury! Make sure that the structural
framework can support a weight factor five times
the total weight of the equipment. If not, reinforce
the structure before installing the mount.
2. With the mount correctly oriented and level, secure the mount
to the wall (see Figure 1) using four fasteners (not included).
Fasteners must be driven into the supporting wall studs or other
supporting framework.
3. Check mount to ensure it is level and adjust to level if
necessary.
INSTALL DISPLAY BRACKETS
Mounting
Holes
Mounting
Holes
Figure 1. Mounting Hole Locations
Security Lock May Be
Installed
Install display bracket(s) according to the instructions provided.
The bracket(s) is/are designed for your specific model.
MOUNT THE DISPLAY
Mount the display as follows:
1. Make sure no power is supplied to the display and the flags are
in the lowered (open) position before attempting to mount the
display.
2. Using two people, slide the display down over the mount.
Make sure all four Q-buttons of the display engage all four
slots in the mount.
3. With the Q-buttons of the display fully engaged in the slots of
the mount, secure the display on the mount by raising the flags
all the way to their locked position. If the flags do not fully
engage, remove the display and make sure the brackets are
correctly installed.
NOTE: A security lock may be installed through the hole in the
locking flag for additional security (see Figure 2).
NOTE: If display does not remain at desired tilt setting, tighten
the nut and bolt on tilt arms on each side (see Figure 3).
Figure 2. Optional Security
Loosen or tighten
this bolt
to adjust tilt tension
Loosen or tighten
this nut
to adjust tilt tension
WARNING: Make sure the flag securing the display is com-
pletely lowered at all times except when removing
or installing the display. The flag must be all the
way down when installing/removing cables.
Figure 3. Tilt Tension Adjustment
3
Page 5
Installation Instructions Pitch-Adjustable Mount PLP91/D
PARTS
Table 1: Parts
Ref Description Qty Ref Description Qty
1 MOUNT 1 5 NUT, Nylock, 10-24 2
2 FLAG, Extended 1 6 FLAG, Locking 1
3 SCREW, 10-24X1/2, FH 1 7 SCREW, 10-24X1/2, Phillips 1
4 WASHER, Nylon 2
1
2
3
4
4
5
6
5
7
4
Page 6
INSTALLATION INSTRUCTIONS
(
PSB-91/D
PLASMA DISPLAY MOUNTING BRACKET
Prior to assembly, unpack carton completely and verify contents.
If you are missing any of the following components, please contact Customer Service at 1-800/582-6480
(2) Plasma Bracket (4) Mounting Buttons – Tapped
(4) 10-24 x ½ Button Head Cap Screw (1) 1/8 Allen Key
(4) M5 x 20mm Phillips Head Cap Screw (4) .875 OD x .33 ID x .375 Nylon Spacer
(4) M6 x 20mm Button Head Cap Screw (1) M4 Allen Key
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
CAUTION!
WARNING!
1. Using a 10-24 button head cap screw inserted from back side of bracket, secure mounting button,
with chamfered hole of mounting button (larger surface) facing bracket, to bracket (four places) (see
Figure 2 & Figure 3).
Figure 1
PLASMA DISPLAYS ARE EXTREMELY FRAGILE.
ALL COMPONENTS MUST BE SECURELY FASTENED TO A
STRUCTURAL MEMBER CAPABLE OF SUPPORTING 4
TIMES THE COMBINED WEIGHT OF ALL COMPONENTS
PLUS THE EQUIPMENT BEING MOUNTED. IF IT CANNOT
SUPPORT THIS WEIGHT, THE STRUCTURE MUST BE
REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE
MOUNT IS 125 POUNDS
56.7 KG).
Figure 2
Figure 3
Sony Electronics Inc. 8805-000185
1 Sony Drive
Park Ridge, NJ 07656
201-930-1000
www.sony.com/displaysystems
Page 7
2. Place Nylon spacers over mounting holes on back of screen.
3. Attach mounting brackets to the display using the M5 screws for 32” screen or M6 for 42” and 50”
screens (see Figure 4 & Figure 5).
4. With the aid of another person, lift your display up to the mount, aligning buttons of mounting
brackets with slots in the mount.
5. Lower safety catch on the mount to secure your display, making sure latch is completely engaged.
Figure 4
Figure 5
Loading...