Sony PFM-510A1WU, PFM-510A1WE, PFM-510A1WJ User Manual

PFM-510A1WU/510A1WE/510A1WJ
3-867-473-01 (1)
Flat Panel Monitor
Operating Instructions Mode d’emploi Bedienungsanleitung Manual de instrucciones Istruzioni per l’uso
取扱説明書
お買い上げいただきありがとうございます。
この取扱説明書には、事故を防ぐための重要な注意事項と製品の取り扱 いかたを示しています。この取扱説明書をよくお読みのうえ、製品を安 全にお使いください。お読みになったあとは、いつでも見られるところ に必ず保管してください。
電気製品は安全のための注意事項を守らないと、 火災や人身事故になることがあります。
GB FR DE ES IT JP
PFM-510A1WU PFM-510A1WE PFM-510A1WJ
1999 by Sony Corporation
WARNING
Owner’s Record
The model and serial numbers are located on the rear. Record the model and serial numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
For the customers in Canada
This class A digital apparatus complies with Canadian ICES-
003.
Serial No.
For PFM-510A1WE users
THIS APPARATUS MUST BE EARTHED IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the safety earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
The socket-outlet should be installed near the equipment and be easily accessible.
Note
When you connect a computer to this monitor, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC/IC/CE (EN55022) standards.
For the customers in Europe
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
2 (GB)
Attaching the ferrite cores
Set the ferrite cores on the both ends of the AC power cord. Close the lid tightly until the clamps click.
or
Clamps
Table of Contents
Precautions ............................................................... 4 (GB)
Features..................................................................... 5 (GB)
Location and Function of Parts and Controls ....... 6 (GB)
Front / Sides ............................................................. 6 (GB)
Control Panel ........................................................... 7 (GB)
Right Connector Panel ............................................. 8 (GB)
Left Connector Panel ............................................. 10 (GB)
Remote Commander RM-921................................ 10 (GB)
Installation............................................................... 12 (GB)
Using the Retractable Feet ..................................... 12 (GB)
Caution................................................................... 13 (GB)
Connections............................................................ 14 (GB)
Connecting the AC Power Cord ............................ 14 (GB)
Connection Example.............................................. 14 (GB)
Using On-screen Menus ........................................ 16 (GB)
Operating Through Menus..................................... 16 (GB)
Menu Guide ........................................................... 16 (GB)
Watching the Picture.............................................. 20 (GB)
Switching the Picture ............................................. 20 (GB)
Input Signal and Monitor Status Information
Display .............................................................. 20 (GB)
Adjusting the Picture ............................................. 22 (GB)
Adjusting the Contrast, Brightness, Chroma,
and Phase .......................................................... 22 (GB)
Restoring the PIC CONTROL Menu Items to Original
Settings ............................................................. 22 (GB)
Resizing and Positioning the Picture ................... 23 (GB)
Resizing the Picture ............................................... 23 (GB)
Adjusting the Picture Position ............................... 23 (GB)
Restoring the Original Picture Size and Position.....
Using the Memory .................................................. 25 (GB)
Storing the Current Condition................................ 25 (GB)
Calling Up the Stored Condition ........................... 25 (GB)
Selecting the On-screen Language ...................... 26 (GB)
Self-diagnosis Function......................................... 26 (GB)
Operating a Specific Monitor with the Remote
Commander ........................................................ 27 (GB)
Using the Other Remote Commander .................. 28 (GB)
Specifications ......................................................... 29 (GB)
24 (GB)
GB

English

3 (GB)

Precautions

Precautions
On safety
•Operate the unit on 100 to 120 V AC or 220 to 240 V AC.
•The nameplate indicating operating voltage, power consumption, etc. is located on the rear.
•Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•Unplug the unit from the wall outlet if it is not to be used for several days or more.
•To disconnect the AC power cord, pull it out by grasping the plug. Never pull the cord itself.
•When the unit is installed on the floor, be sure to use the retractable feet.
On installation
•Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.
•Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•When you install multiple equipment with the unit, the following, such as Remote Commander’s malfunction, noisy picture, noisy sound, may occur depending on the position of the unit and other equipment.
On repacking
Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it as illustrated on the carton.
If you have any questions about this unit, contact your authorized Sony dealer.
On PDP (Plasma Display Panel)
•There may be some tiny black points and/or bright points on the PDP. These points are normal.
•Do not display a same still image on the screen for long, consecutive time. Otherwise, the afterimage may appear on a part of a panel. Use the screen saver eventually to equalize the screen display.
On cleaning
To keep the unit looking brand-new, periodically clean it with a mild detergent solution. Never use strong solvents such as thinner or benzine, or abrasive cleansers since these will damage the cabinet. As a safety precaution, unplug the unit before cleaning it.
4 (GB)

Features

The PFM-510A1W series are 16:9 42-inch flat panel monitor adopting the PDP (Plasma Display Panel) and accepts various types of signals with the built-in scan converter.
Improved image quality
The PDP achieves higher image quality with 1024 × 1024 lines. This makes for finely-detailed HDTV and PC images. You can get greater brightness and contrast over conventional monitors.
Internal high-performance scan converter
The monitor has a high performance scan converter. Using a unique algorithm, the monitor processes signals in a wide range of formats – Video, HDTV, PC, etc.
Flexibility
An option slot is in place for future expansion. The slot-in option adapter allows for quick and easy system upgrades.
Features
Other features
•Three sets of video inputs with audio inputs: one composite video or Y/C inputs, one RGB input, and one RGB/component input.
•Displays the HDTV signal with tri-level sync signal.
•Three dimensional comb filter for NTSC Y/C separation.
•Line correlation comb filter for PAL Y/C separation.
•Automatic input signal detection with indication.
1)
•Windows95/98
PnP (Plug and Play) compatible.
•Picture AGC function — this function automatically adjusts and improves the contrast when a low intensity signal is input.
•On-screen menu for various adjustments and settings
•On-screen display in five languages for user-friendly access.
•Fine adjustment of image size and position
•Memory function for storage of up to five picture settings.
•ID control
•Self-diagnosis function.
•Remote (RS-232C) connector (mini DIN 8-pin)
•Control-S connector
•Accepts infrared or wired Sony Remote Commanders using SIRCS code.
•Vertical setup
Warning on power connection
Use a proper power cord for your local power supply.
United States, Continental United Kingdom, Ireland, Japan Canada Europe Australia, New Zealand
Plug type VM0033B COX-07 636 VM1296 Female end VM0113 COX-02 VM0310B VM0303B VM1313 Cord type SJT H05VV-F CEE (13) 53rd (O.C) HVCTF Minimum cord set rating 13A/125V 10A/250V 10A/250V 10A/125V Safety approval UL/CSA VDE VDE DENTORI
.........................................................................................................................................................................................................
1) Windows95/98 is a registered trademark of the Microsoft Corporation.
5 (GB)

Location and Function of Parts and Controls

Location and Function of Parts and Controls

Front / Sides

5 Right connector panel
For details on the right connector panel, see “Right Connector Panel” on page 8 (GB).
6 Right panel cover
Open it when using the right connector panel.
For details on opening the panel cover, see the below on this page.
Front
Left side
1
Right side
To open the panel cover
Loosen the screws counterclockwise and open the cover.
2
To take off the panel cover
Loosen the screws as illustrated below and take off the panel cover.
6
Screws
3
4
5
1 Retractable feet
Use for setting the monitor on the floor.
For details on using the retractable feet, see “Using the
Retractable Feet” on page 12 (GB).
2 Control panel
For details on the control panel, see “Control Panel” on
page 7 (GB).
3 Left panel cover
Open it when using the left connector panel. You can install the Remote Commander in the back of
this cover.
For details on opening the panel cover, see the right on this
page.
4 Left connector panel
For details on the left connector panel, see “Left Connector
Panel” on page 10 (GB).
6 (GB)
To install the Remote Commander in the panel cover
Install the Remote Commander in the back of the left panel cover as illustrated below.
Remote Commander
Note
When housing the Remote Commander, make sure that the top of the Remote Commander faces upward and rear faces outside.

Control Panel

Location and Function of Parts and Controls
VOL – VOL + MENU ENT RGB1 YUV RGB2 LINE Y/C CTRL
qd qs qa 0 98765 4 32 1
mM
1 Remote control detector
Receives the beam from the Remote Commander.
2 1 (standby) switch/1 (standby) indicator
Press to turn the monitor on. Press again to go back to the standby mode. The 1 (standby) indicator lights up in red in the standby mode.
When the 1 indicator flashes, see “Self-diagnosis Function” on page 26 (GB).
3 Power indicator
Lights up when the monitor is turned on.
4 CTRL (control) button
To operate the buttons on the control panel, first press this button. Then the buttons light up or flash that show they can be operated. Press again to deactivate them.
1
9 RGB1 button
Select the RGB signal input from the RGB1 connectors.
0 ENT (enter) button
Press to select the desired item in a menu.
qa M/m buttons
Press to move the cursor (B) to an item or to adjust value in a menu.
qs MENU button
Press to make the menu appear.
qd VOL (volume) +/– buttons
Press the + button to increase the volume, or the – button to decrease the volume.
Note
The buttons (except for 1 (standby) switch 2) on the control panel do not function if you do not press the CTRL button first.
5 Y/C button
Select the signal input from the Y/C IN jack in the LINE connectors.
6 LINE button
Select the signal input from the VIDEO IN connector in the LINE connectors.
7 RGB2 button
Select the signal input from the RGB2 connectors.
8 YUV button
Select the component signal input from the RGB1 connectors.
7 (GB)
Location and Function of Parts and Controls

Right Connector Panel

RGB 1
IN OUT
R
R-Y
G Y
B
B-Y
1
2
3
Note
The image enhancing process for video signals (NTSC, PAL) works only for composite (Y/C) or component (Y/R-Y/B-Y) input. The image from the RGB input may looked blurred. This is normal.
HD/
COMP
VD
L
R
RGB 2
RGB IN
L
R
VIDEO
Y/C
L
R
IN OUT
LINE
REMOTE
(RS-232C)
4
SYNC
AUDIO
AUDIO IN
5
AUDIO
6
1 RGB1 IN connectors
R (R-Y)/G (Y)/B (B-Y) IN (BNC-type): Input the
analog RGB signal or component signal. Connect to the RGB signal or component (Y/B-Y/R-Y) signal output of a computer or video equipment. This unit also accepts the HD analog component
B/PR) signal. Input the PB signal to the B (B-
(Y/P Y) IN connector and P
R signal to the R (R-Y) IN
connector.
HD/COMP IN (BNC-type): Input the H sync signal
or composite sync signal. Connect to the H sync signal or composite sync signal output of a computer or video equipment.
VD IN (BNC-type): Input the V sync signal.
Connect to the V sync signal output of a computer or video equipment.
External sync signal is selected automatically. See the priority chart below.
Input Input sync signals connector
HD/COMP IN H Sync Comp Sync — VD IN V Sync — G(Y) IN Sync on G Sync on G Sync on G Sync signals
to be selected
H Sync Comp Sync Sync on G V Sync
AUDIO IN (L/R) (phono type): Input the audio
signal. Connect to the audio output of a computer or video equipment. Connect to the channel L when the audio signal is monaural.
2 RGB2 IN connectors
RGB IN (D-sub 15-pin): Connect to the RGB signal
output of a computer.
AUDIO IN (L/R) (phono type): Input the audio
signal. Connect to the audio output of a computer. Connect to the channel L when the audio signal is monaural.
3 LINE IN connectors
VIDEO IN (BNC-type): Connect to the composite
video signal output of the video equipment.
Y/C IN (Mini DIN 4-pin): Connect to the Y/C
signal output of the video equipment.
AUDIO IN (L/R) (phono type): Connect to the
audio output of the video equipment. Connect to the channel L when the audio signal is monaural.
8 (GB)
Location and Function of Parts and Controls
4 RGB1 OUT connectors
These connectors are used as loop-through outputs of the RGB1 IN connectors 1. When the plug is connected to the RGB OUT connectors, the 75-ohms termination of the RGB IN connectors is released, and the signal input to the RGB IN connectors is output from the these connectors.
R (R-Y)/G (Y)/B (B-Y) OUT (BNC-type): Loop-
through outputs of the RGB IN connectors. Connect to the RGB signal or component (Y/B­Y/R-Y) signal input of another monitor.
HD/COMP OUT (BNC-type): Loop-through output
of the HD/COMP IN connector. Connect to the H sync signal or composite sync signal input of another monitor.
VD OUT (BNC-type): Loop-through output of the
VD IN connector. Connect to the V sync signal input of another monitor.
Note
The HD/COMP OUT and VD OUT connectors are high impedance outputs. When using these outputs, connect a monitor with high impedance sync input connector, or the picture might be oscillated or disappeared because of the sync signal level mismatch.
6 REMOTE (RS-232C) connector (mini DIN 8­pin)
This connector allows remote control of the monitor using the RS-232C protocol. For details, see your authorized Sony dealer.
AUDIO OUT (L/R) (phono type): Loop-through
outputs of the AUDIO IN jacks. Connect to the audio inputs of another monitor.
5 LINE OUT connectors
These connectors are used as loop-through outputs of the LINE IN connectors 3. When the plug is connected to the VIDEO OUT connector or Y/C OUT jack, the 75-oms termination of the VIDEO IN connector or Y/C IN jack is released, and the signal input to the VIDEO IN or Y/C IN jack is output from the VIDEO OUT connector or Y/C OUT jack.
VIDEO OUT (BNC-type): Connect to the
composite video signal input of another monitor or video equipment.
Y/C OUT (Mini DIN 4-pin): Connect to the Y/C
signal input of another monitor or video equipment.
AUDIO OUT (L/R) (phono type): Loop-through
outputs of the AUDIO IN jacks. Connect to the audio inputs of another monitor or video equipment.
9 (GB)
Location and Function of Parts and Controls

Left Connector Panel

MONITOR OUT
AUDIO
RL
VARIABLE
CONTROL S
IN
+
R–
SPEAKERS
(6-16 Ω)
SERVICE CODE
OUT
8.8.
Notes
•If you connect the CONTROL S IN jack to the other equipment’s CONTROL S OUT jack, you cannot operate the monitor with the Remote Commander.
•You can use the stereo cable with mini plug instead
1
2
+ L
3
of the control S cable.
3 SPEAKERS L/R terminals
Connect to speakers with 6 to 16 ohms impedance.
Note
Do not connect the speaker’s cord to the monitor and to an amplifier simultaneously, or an excessive electric current might flow from the amplifier and damage the monitor.
4 SERVICE CODE indicator
4
The indicator is only for qualified personnel.
5 -AC IN socket
Connect the supplied AC power cord to this socket and to a wall outlet. Once you connect the AC power cord, the monitor turns to standby mode.
5
AC IN
1 MONITOR OUT AUDIO (L/R) jacks (phono type)
Output the signal input from the AUDIO IN jacks. Connect to the audio inputs of an audio amplifier (not supplied).
Note
These jacks are variable outputs. Set the volume to maximum position to set the output level to 500 mVrms.
2 CONTROL S IN/OUT jacks (mini jacks)
Connect to the CONTROL S jacks of video equipment or another monitors. Then you can simultaneously control all equipment with a single Remote Commander. To control equipment by aiming the supplied Remote Commander to the remote control detector of the monitor, connect the CONTROL S OUT jack of the monitor and the CONTROL S IN jack of other equipment.

Remote Commander RM-921

1
DISPLAY
RGB2
Y/C
2 5 8
ZOOM
SELECT
VOL
POWER
YUV
MTS/MPX
3 6 9
CH
DEGAUSS
MENU
ENTER
CH
2 3
4 5
6
7 8
9 0
qa
MUTING
RGB1
LINE
1 4 7
10/0
STILL
POWER
ON
OFF
ON
SET
OFF
ID MODE
qs
qd qf
qg
qh qj qk
ql» w;…
wa
10 (GB)
Location and Function of Parts and Controls
1 POWER switch
Press to turn on the monitor. Press again to go back to the standby mode.
Note
When using multiple monitors, press this switch to turn monitors which are already on into the standby mode, or turn on monitors which are in the standby mode.
2 MUTING button
Press to mute the sound. Press this button again or press the VOL (volume) +/– button to obtain the sound again.
3 RGB1/RGB2 buttons
Select the signal input from the RGB1 or RGB2 connectors.
4 LINE button
Selects the signal input from the VIDEO IN connector in the LINE connectors.
5 Y/C button
Selects the signal input from the Y/C IN jack in the LINE connectors.
qs DISPLAY button
Displays the input signal information on the top of the monitor screen. Press again to clear it.
qd YUV button
Selects the component signal input from the RGB1 connectors.
qf MTS/MPX button
This button does not operate with the monitor.
qg CH button
This button does not operate with the monitor.
qh DEGAUSS button
This button does not operate with the monitor.
qj SELECT +M/–m buttons
Press to move the cursor (B) to an item or to adjust value in a menu.
qk MENU button
Press to make the menu appear.
ql ENTER button
Press to select the desired item in a menu.
6 Number buttons
Press to select the index number.
7 ZOOM button
This button does not operate with the monitor.
8 STILL button
This button does not operate with the monitor.
9 POWER ON switch
Press to turn on the monitor. When you use multiple monitors, you can use this switch instead of the POWER switch 1 not to affect another monitor which is already turned on.
0 POWER OFF switch
Press to turn the monitor into the standby mode. When you use multiple monitors, you can use this switch instead of the POWER switch 1 not to affect another monitor which are in the standby mode.
qa ID MODE (ON/SET/OFF) buttons
Press the ON button to make an index number appear on the screen. Then press the index number of the monitor you want to operate and press the SET button. After you finish the operation, press the OFF button to return to the normal mode.
w; VOL +/– buttons
Press the + button to increase the volume, or the – button to decrease the volume.
wa CH +/– buttons
This button does not operate with the monitor.
11 (GB)
Location and Function of Parts and Controls / Installation
Installing batteries
Insert two size AA (R6) batteries in correct polarity.

Installation

Using the Retractable Feet

Be sure to install the negative < end first.
E
e
•In normal operation, batteries will last up to half a year. If the Remote Commander does not operate properly, the batteries might be exhausted. Replace them with new ones.
•To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the Remote Commander for a fairly long time.
When the Remote Commander does not work
Check that the 1 indicator lights up. The Remote Commander operates the monitor only when the monitor is turned on, or it is in the standby mode.
e
E
This section describes the installation arrangements for installing the projector.
1 Pull out the knobs and pull down the retractable
feet.
2 Turn the retractable feet outward.
3 Push in the retractable feet and lock.
Note
If you connect the cable to the CONTROL S IN jack on the side of the monitor, you cannot operate the monitor with the Remote Commander.
To fix the retractable feet
When the unit is installed on the floor, be sure to fix the retractable feet. Install the foot support brackets as illustrated below.
12 (GB)
Installation

Caution

•When you install the monitor, make sure there is more space than that shown in the figure below.
•The ambient temperature must be 0°C – +35°C (32°F – 95°F).
When using the retractable feet
Front
Wall
20 (7 7/8)
Side
10
Wall Wall
(4)
Floor
5.5 (2 1/4)
10
(4)
2.5 (1)
Side
3.5 (1 7/8)
Wall
Hooked on the wall: Vertically
Front
Wall
10 (4)
20
(7 7/8)
Make sure that the control section is at the bottom.
10 (4)
Wall
Units: cm (inches)
25
(9 7/8)
WallWall
Wall
Floor
Units: cm (inches)
When using the mounting bracket
Front
Wall
25 (9 7/8)
10
Wall Wall
(4)
7
25 (9
/8)
Wall
10 (4)
Side
5 (2)
Wall
Units: cm (inches)
13 (GB)

Connections

Connections

Connecting the AC Power Cord

1 Plug the power cord into the AC IN socket. Then,
attach the AC plug holder (supplied) to the AC power cord.
AC power
AC IN socket
2 Slide the AC plug holder over the cord until it
connects to the AC IN socket cover.
cord
AC plug holder
AC IN socket cover
To remove the AC power cord
Squeeze the upper and lower sides and pull out the AC plug holder.

Connection Example

Before you get started
•First make sure that the power to each piece of equipment is turned off.
•Use connecting cables suitable for the equipment to be connected.
•The cable connectors should be fully inserted into the jacks. A loose connection may cause hum and other noise.
•To disconnect the cable, pull out by grasping the plug. Never pull the cable itself.
•Read the instruction manual of the equipment to be connected.
14 (GB)
Connections
to audio output
Computer
to video output
to audio output
to video output
* to R(R-Y)/G(Y)/
B(B-Y), HD/COMP, VD IN
to AUDIO IN
to RGB IN
to Y/C or VIDEO IN
RGB 1
IN OUT
R-Y
B-Y
HD/
COMP
VD
RGB 2
RGB IN
VIDEO
Y/C
Betacam SP video cassette recorder
to component signal output
R
G Y
B
to audio output
* to R(R-Y)/G(Y)/
SYNC
B(B-Y) IN
to AUDIO IN
L
AUDIO
R
L
AUDIO IN
R
to AUDIO IN
to video output
VCR, laser disc player, game machine, etc.
* cannot be used at the same time.
to audio output
to AUDIO IN
L
R
IN OUT
LINE
AUDIO
15 (GB)

Using On-screen Menus

Using On-screen Menus

Operating Through Menus

Menu operating buttons
4 Press M/m to adjust or select the setting and press
ENT to set. The setting is registered and the menu returns to the previous menu.
To return to the normal screen, press the MENU button repeatedly until the menu disappears.
There are four buttons on the monitor and the Remote Commander for menu operations.
Remote Commander Monitor
SELECT
MENU
ENTER
MENU ENT
m
M
The buttons on the control panel are used for explanation purpose in this operating instructions. The ENTER button on the Remote Commander has the same function as the ENT button on the control panel and the SELECT +M/–m buttons on the Remote Commander as same as the M/m buttons on the control panel.
Configuration of the menu
To select the language used in the menu, see page 26 (GB).
Menu Guide
Note
“– – – –” appears next to an item when its function is not available. The availability depends on the types of input signal.
PIC CONTROL menu
This menu is used for adjusting the picture.
1 2 3 4 5 6
1 CONTRAST
Press M to increase the contrast and press m to decrease it.
PIC CONTROL
CONTRAST : 80 BRIGHTNESS : 00 CHROMA : 0 0 PHASE : 00 COLOR TEMP :H IGH RESET
SELECT CANCEL
ENTER
MENU
1 Press MENU.
The main menu appears on the monitor screen.
MA IN MENU
PIC CONTROL
PIC SIZE CONF I G MEMORY REMOTE
STATUS
SELECT CANCEL
ENTER
MENU
2 Press M/m to move the cursor (B) and press ENT
to select a menu. The selected menu appears on the monitor screen.
3 Press M/m to move the cursor (B) and press ENT
to select an item. The menu for the selected item appears on the monitor screen.
2 BRIGHTNESS
Press M to make the picture brighter and press m to make it darker.
3 CHROMA
Press M to increase color saturation and press m to decrease it.
4 PHASE
Press M to make overall picture greenish and press m to make it purplish.
5 COLOR TEMP
Select a color temperature from HIGH or LOW.
6 RESET
Select to restore the factory settings in the PIC CONTROL menu items 1 to 5.
For details on using the reset function, see “Restoring the PIC CONTROL Menu Items to Original Settings” on page 22 (GB).
16 (GB)
Using On-screen Menus
PIC SIZE menu
This menu is used for positioning and resizing the picture.
7 8 9 0 qa qs
7 H SIZE
Adjusts the horizontal picture size. Press M to enlarge the horizontal size and press m to diminish it.
8 H SHIFT
Adjusts the horizontal centering. Press M to move the picture to the right and press m to move it to the left.
9 V SIZE
Adjusts the vertical picture size. Press M to enlarge the vertical size and press m to diminish it.
q; V SHIFT
Adjusts the vertical centering. Press M to move the picture up and press m to move it down.
qa ASPECT
Set the aspect ratio of the picture to 4:3 or 16:9.
qs RESET
Select to restore the factory settings in the PIC SIZE menu items 7 to qa.
For details on using the reset function, see “Restoring the Original Picture Size and Position” on page 24 (GB).
Note
When receiving DTV signals and changing the H/V SIZE or H/V SHIFT in the PIC SIZE menu, the system goes into the Offset Sampling Mode; the image may become blurred or horizontal lines may appear because the memory write phase is faster than the read phase. This is not a system malfunction. To avoid this problem, reset the H/V SIZE and the H/ V SHIFT to the factory settings. If any problems persist with the factory setting, adjust the settings as shown below. To adjust the setting, see “Restoring the original Picture Size and Position” (page 24 (GB)).
PIC SIZE
HSIZE : 00 HSHIFT : 00 VSIZE : 00 VSHIFT : 00 ASPECT : 4x3 RESET
SELECT CANCEL
ENTER
MENU
•DTV signals for factory setting: 1080/60i, 480/60i, 575/50i, 480/60p
•Other DTV signals and their recommended settings:
HVHV
SIZE SIZE SHIFT SHIFT
1080/50i + 48 + 11 + 10 – 02 16:9 1080/48i MAX + 09 + 12 – 02 16:9 1152/50i + 33 – 02 + 20 0 16:9
ASPECT
CONFIG menu
This menu is used for adjusting the signal or selecting the language.
qd qf qg qh
qd ENHANCE (Sharpness)
You can change the outline correction level:
LOW: Default setting for VIDEO signal HIGH: Default setting for computer signal
qf H FILTER
Select AUTO normally. Select HIGH when the ringing appears on the screen. Select LOW when the moiré pattern or noise appears on the screen. The moiré pattern or noise decreases even the screen looks a little blurred.
qg DISPLAY
Select ON to display the input signal information for about five seconds on the top of the monitor screen when turning on the power or switching the input signal.
qh LANGUAGE
Select the on-screen language among five languages. Available languages are: English, German, French, Italian and Spanish.
For details on selecting the language, see “Selecting the On-screen Language” on page 26 (GB).
CONF I G
ENHANCE :HIGH H FI LTER :AUTO DISPLAY : ON LANGUAGE
SELECT CANCEL
ENTER
MENU
17 (GB)
Using On-screen Menus
MEMORY menu
This menu is used for saving or recalling the settings in the PIC CONTROL, PIC SIZE and CONFIG (only for ENHANCE and H FILTER) menus.
MEMORY
qj qk
LOAD SAVE
SELECT CANCEL
ENTER
MENU
For details, see “Using the Memory” on page 25 (GB).
qj LOAD
Recalls the preset settings.
qk SAVE
Saves the settings.
REMOTE menu
wa REMOTE ONLY
Select ON to disable the front control buttons on the monitor. The monitor can only be controlled with the Remote Commander. While REMOTE ONLY is ON, the indicators on the front panel go off. To cancel the REMOTE ONLY mode, set REMOTE ONLY to OFF with the Remote Commander, or press the CTRL button while pressing the 1 switch. The monitor turns to the standby mode and the REMOTE ONLY mode is canceled. The setting in this item is still retained when the AC power cord is disconnected.
STATUS menu
This menu is used for displaying the internal condition of the monitor.
ws wd wf wg wh wj
STATUS
[ PFM-510A1WU ] SERIAL No. : 2000001 OPERATION :000000H SOFTWARE : TEMPERATURE : OK FAN : OK
Ver
1.00
This menu is used for the remote control setting.
ql w; wa
REMOTE
INDEX NO. : 001 REMOT E MODE : TV REMOTE ONLY : OFF
SELECT CANCEL
ENTER
MENU
ql INDEX NO.
Sets the index number of the monitor.
Note
When you set the number, use the buttons on the monitor.
For details on the index number, see “Operating a Specific Monitor With the Remote Commander” on page 27 (GB).
w; REMOTE MODE
Select the Remote Commander mode.
TV: Sony monitors’ or TVs’ commander PJ: Sony projectors’ commander OFF: Disables the remote control.
For details, see “Using the Other Remote Commander” on page 28 (GB).
ws Model name
Indicates the model name.
wd SERIAL No.
Indicates the serial number.
wf OPERATION
Indicates the total operation hours.
Note
The standby mode is not counted as OPERATION time.
wg SOFTWARE
Indicates the system software version.
wh TEMPERATURE
Indicates whether the internal temperature of the monitor is usual.
OK: Usual NG: Unusual
When the internal temperature is unusual, NG is displayed and the item flashes in red. The 1 indicator on the control panel also flashes.
18 (GB)
Note
The “TEMPERATURE NG” message may appear when the ventilation holes are blocked or the monitor is installed in a poorly ventilated area. In this case, check that the ventilation holes are not blocked and install the monitor in a good ventilated area. If the message still displayed, contact your authorized Sony dealer.
When the 1 indicator flashes or NG indicates, see “Self­diagnosis Function” on page 26 (GB).
wj FAN
The cooling fans are built in this monitor. This item indicates whether the cooling fans work properly.
OK: Usual NG: Unusual
When the cooling fans are unusual, NG is displayed and the item flashes in red. The 1 indicator on the control panel also flashes.
Using On-screen Menus
Note
When the “FAN NG” message appears, contact your authorized Sony dealer.
When the 1 indicator flashes or NG indicates, see “Self­diagnosis Function” on page 26 (GB).
Cooling fans
Ventilation holes
Note
The upper cooling fans detect the monitor’s internal temperature and control the fans rotations. If the ambient temperature is high, the number of fan rotations increase and the noise will be louder.
19 (GB)

Watching the Picture

Watching the Picture
Before you start
•Turn on the monitor.
•Turn on the connected equipment and play a video source.
•To display the input signal information on the screen when turning on the power or switching the input signal, set “DISPLAY” in the CONFIG menu to ON.
•To select the on-screen language used in the menu, see page 26 (GB).

Switching the Picture

1 Press CTRL on the control panel of the monitor.
RGB1, YUV, RGB2, LINE, and Y/C buttons light up.
2 Select the input source to be displayed by pressing
the following buttons. RGB1:Selects the audio and video signal input
from the RGB1 connectors when the input signal is RGB signal.
YUV: Selects the audio and video signal input
from the RGB1 connectors when the input signal is component signal.
RGB2:Selects the audio and video signal input
from the RGB2 connectors.
LINE: Selects the audio and video signal input
from the VIDEO IN connector and AUDIO IN jack in the LINE connectors.
Y/C: Selects the audio and video signal input
from the Y/C IN connector and AUDIO IN jack in the LINE connectors.
Color system or horizontal/vertical frequency
Note
We recommend the input source video equipment equipped with the TBC (time base corrector). If you receive the signal without the TBC, the picture may disappear due to disturbance of the sync signal.

Input Signal and Monitor Status Information Display

Input signal and monitor status information is displayed on-screen for about five seconds when turning on the power or switching the input signal. To disable this function, follow the steps below.
1 Press MENU.
The main menu appears on the monitor screen.
MA IN MENU
PIC CONTROL PIC SIZE CONF I G MEMORY REMOTE STATUS
SELECT CANCEL
ENTER
MENU
2 Press M/m to move the cursor (B) to “CONFIG”
and press ENT. The CONFIG menu appears on the monitor screen.
CONF I G
ENHANCE :HIGH H F ILTER :AUTO DISPLAY : ON LANGUAGE
SELECT CANCEL
ENTER
MENU
Signal type
PAL LINE·Y/C
The selected input signal appears on the monitor screen.
You can also switch the input signal from the Remote Commander.
20 (GB)
3 Press M/m to move the cursor (B) to “DISPLAY”
and press ENT. The following menu appears on the monitor screen.
DISPLAY : ON
Watching the Picture
4 Press M to set “DISPLAY” to OFF and press
ENT. The DISPLAY function is disabled.
To activate the information function, set “DISPLAY” to ON at the step 4 above.
Note
You can display the input signal information anytime by pressing the DISPLAY button on the Remote Commander, regardless of the above setting.
The input signal information list
Color system or horizontal/vertical frequency
31.5
kHz
/60
Signal type
RGB1 ·RGB
Hz
Actual on-screen display of the monitor status
On-screen display Significance
31.5kHz / 60Hz (eg.) The selected input signal is computer RGB.
525 / 60 (eg.) The selected input signal is RGB or
component video.
NTSC The selected input signal is NTSC. PAL The selected input signal is PAL. OTHERS The input signal is out of the
capture range.
NO SYNC There is no input signal. MUTING The sound is muted. RGB1 RGB The signal mode of RGB1 is set to
RGB.
RGB1 YUV The signal mode of RGB1 is set to
component video.
LINE COMP Composite video input is selected at
LINE.
LINE Y/C Y/C video input is selected at LINE.
Input signal Color system or horizontal/vertical
NTSC NTSC PAL PAL VGAa) (Graphics) 31.5 kHz 60 Hz VGA (Text) 31.5 kHz 70 Hz HDTV 33.8 kHz 60 Hz Macb) 13" 35.0 kHz 67 Hz VESAc) 800×600 37.9 kHz 60 Hz VESA 1024×768 48.4 kHz 60 Hz Mac 16" 49.7 kHz 75 Hz ATId) 1280×1024 64.0 kHz 60 Hz Mac 21" 68.7 kHz 75 Hz VESA 1280×1024 80.0 kHz 75 Hz
frequency display
a) VGA is a registered trademark of the International
Business Machines Corporation, USA.
b) Mac (Macintosh) is a registered trademark of Apple
Computer, Inc.
c) VESA is a registered trademark of Video Electronics
Standard Association.
d) ATI is a registered trademark of ATI Technologies, Inc.
Note
When inputting the HDTV signal, input the tri-level sync signal to the G/Y IN connector.
21 (GB)

Adjusting the Picture

Adjusting the Picture
While watching the picture, you can adjust contrast, brightness, chroma, and phase to suit your taste. The adjustments can be carried out for each input signal separately. You can also store the adjusted levels in memory.

Adjusting the Contrast, Brightness, Chroma, and Phase

Press MENU so that the main menu appears on the monitor screen and select the “CONTRAST”, “BRIGHTNESS”, “CHROMA”, or “PHASE” from the PIC CONTROL menu with the M/m buttons.
CONTRAST
Select the “CONTRAST” with the M/m buttons and press the ENT button. Adjust the contrast with the M/m buttons in the range from MIN (0) to MAX (+100).
M: to increase picture contrast m: to decrease picture contrast
Notes
•CHROMA and PHASE controls do not function with RGB signal.
•PHASE control does not function with component signal.
•PHASE control does not function with PAL color source.
•Do not change the CHROMA/PHASE (NTSC only) level when the selected signal is not NTSC or PAL. Although it gives no effect to the current picture, it does affect the picture of the NTSC or PAL signal which is input later.

Restoring the PIC CONTROL Menu Items to Original Settings

1 In the PIC CONTROL menu, Press M/m to move
the cursor (B) to “RESET” and press ENT. The following menu appears on the monitor screen.
RESET : NO
BRIGHTNESS
Select the “BRIGHTNESS” with the M/m buttons and press the ENT button. Adjust the brightness with the M/m buttons in the range from MIN (–50) to MAX (+50).
M: to make overall picture greenish m: to make overall picture purplish
CHROMA
Select the “CHROMA” with the M/m buttons and press the ENT button. Adjust the chroma with the M/m buttons in the range from MIN (–50) to MAX (+50).
M: to increase color intensity m: to decrease color intensity
PHASE
Select the “PHASE” with the M/m buttons and press the ENT button. Adjust the phase with the M/m buttons in the range from MIN (–50) to MAX (+50).
M: to make overall picture greenish m: to make overall picture purplish
SELECT CANCEL
ENTER
MENU
2 Press M/m.
“NO” changes to “YES”.
RESET : YES
SELECT CANCEL
ENTER
MENU
3 Press ENT.
The PIC CONTROL menu items are restored.
To cancel the reset function, press the MENU button before pressing the ENT button.
22 (GB)
Resizing and Positioning

Resizing and Positioning the Picture

5 Press ENT.
The menu returns to the PIC SIZE menu.
the Picture
You can shift the position of the picture so that it fits in the screen, or adjust the vertical and horizontal size of the picture separately.

Resizing the Picture

1 Press MENU.
The main menu appears on the monitor screen.
MA IN MENU
PIC CONTROL PIC SIZE CONF I G MEMORY REMOTE STATUS
SELECT CANCEL
ENTER
2 Press M/m to move the cursor (B) to “PIC SIZE”
and press ENT. The PIC SIZE menu appears on the monitor screen.
MENU
6 Press M/m to move the cursor (B) to “V SIZE”
and press ENT. The following menu appears on the monitor screen.
VSIZE : 00
7 Press M/m to resize the picture.
M: to expand vertical size m: to reduce vertical size
The vertical picture size is indicated on the monitor screen from MIN(–50) to MAX(+50). The factory value is 00.
8 Press ENT.
The menu returns to the PIC SIZE menu.

Adjusting the Picture P osition

PIC SIZE
HSIZE : 00 HSHIFT : 00 VSIZE : 00 VSHIFT : 00 ASPECT : 4x3 RESET
SELECT CANCEL
ENTER
MENU
3 Press M/m to move the cursor (B) to “H SIZE”
and press ENT. The following menu appears on the monitor screen.
HSIZE : 00
4 Press M/m to resize the picture.
M: to expand horizontal size m: to reduce horizontal size
The horizontal picture size is indicated on the monitor screen in the range from MIN(–50) to MAX(+50). The factory value is 00.
1 In the PIC SIZE menu, press M/m to move the
cursor (B) to “H SHIFT” and press ENT. The following menu appears on the monitor screen.
HSHIFT : 00
2 Press M/m to shift the picture.
M: to shift the picture to the right m: to shift the picture to the left
The horizontal picture position is indicated on the monitor screen from MIN(–50) to MAX(+50). The factory value is 00.
3 Press ENT.
The menu returns to the PIC SIZE menu.
23 (GB)
Resizing and Positioning the Picture
4 Press M/m to move the cursor (B) to “V SHIFT”
and press ENT. The following menu appears on the monitor screen.
VSHIFT : 00
5 Press M/m to shift the picture.
M: to shift the picture upward m: to shift the picture downward
The vertical picture position is indicated on the monitor screen from MIN(–50) to MAX(+50). The factory value is 00.
6 Press ENT.
The menu returns to the PIC SIZE menu.
3 Press ENT.
The original picture size and position are restored.
To cancel the reset function, press the MENU button before pressing the ENT button.

Restoring the Original Picture Size and Position

1 In the PIC SIZE menu, press M/m to move the
cursor (B) to “RESET” and press ENT. The following menu appears on the monitor screen.
RESET : NO
SELECT CANCEL
ENTER
MENU
2 Press M/m.
“NO” changes to “YES”.
RESET : YES
24 (GB)
SELECT CANCEL
ENTER
MENU

Using the Memory

You can save the current picture condition by each input signal using MEMORY function. The saved condition can be restored whenever necessary. The items in PIC CONTROL, PIC SIZE and CONFIG (only for ENHANCE and H FILTER) menus can be memorized. You can save the picture condition of up to five input signals.

Storing the Current Condition

1 Press MENU.
The main menu appears on the monitor screen.
MA IN MENU
PIC CONTROL PIC SIZE CONF I G MEMORY REMOTE STATUS
SELECT CANCEL
ENTER
2 Press M/m to move the cursor (B) to “MEMORY”
and press ENT. The MEMORY menu appears on the monitor screen.
MEMORY
LOAD SAVE
MENU
Using the Memory
“COMPLETED” message appears for about five seconds. The current data is stored under the selected memory number. If any data has been stored in the selected memory number, the signal type and the color system or horizontal frequency/vertical frequency are now displayed on the right column next to the selected memory number.
Signal type
Color system or horizontal/vertical frequency
SAVE
MEM 1:RGB 31.5 MEM 2 : EMPTY MEM 3 : EMPTY MEM 4 : EMPTY MEM 5 : EMPTY
SELECT CANCEL
ENTER
kHz60Hz
MENU

Calling Up the Stored Condition

1 In the MEMORY menu, press M/m to move the
cursor (B) to “LOAD” and press ENT. The following menu appears on the monitor screen.
LOAD
MEM 1 : RGB 31 . 5 MEM 2 : EMPTY MEM 3 : EMPTY MEM 4 : EMPTY MEM 5 : EMPTY
SELECT CANCEL
ENTER
kHz60Hz
MENU
SELECT CANCEL
ENTER
MENU
3 Press M/m to move the cursor (B) to “SAVE” and
press ENT. The following menu appears on the monitor screen.
SAVE
MEM 1 : EMPTY MEM 2 : EMPTY MEM 3 : EMPTY MEM 4 : EMPTY MEM 5 : EMPTY
SELECT CANCEL
ENTER
MENU
4 Press M/m to move the cursor (B) to MEM 1 to 5
and press ENT.
2 Press M/m to move the cursor (B) to MEM 1 to 5
and press ENT. “COMPLETED” message appears for about five seconds. The picture is adjusted to the selected condition.
Notes
•You cannot recall the memory data if the selected signal is different from the preset signal.
•The following items can be memorized:
PIC CONTROL menu
– CONTRAST – BRIGHTNESS – CHROMA – PHASE – COLOR TEMP – PICTURE AGC
25 (GB)
Using the Memory / Selecting the On-screen Language / Self-diagnosis Function
PIC SIZE menu
– H SIZE – H SHIFT – V SIZE – V SHIFT – ASPECT
CONFIG menu
– ENHANCE – H FILTER

Selecting the On-screen Language

You can select the on-screen language among five languages. Available languages are: English, German, French, Italian and Spanish.
1 Press MENU.
The main menu appears on the monitor screen.
3 Press M/m to move the cursor (B) to
“LANGUAGE” and press ENT. The following menu appears on the monitor screen.
LANGUAGE
ENGL I SH DEUTSCH FRANÇA I S
ITALIANO
ESPAÑOL
SELECT CANCEL
ENTER
MENU
4 Press M/m to move the cursor (B) to desired
language and press ENT. The on-screen language is switched to the one you selected.
ENGLISH: English DEUTSCH: German FRANÇAIS: French ITALIANO: Italian ESPAÑOL: Spanish
5 Press MENU.
The menu returns to the CONFIG menu.
MA IN MENU
PIC CONTROL PIC SIZE CONF I G
MEMORY
REMOTE STATUS
SELECT CANCEL
ENTER
MENU
2 Press M/m to move the cursor (B) to “CONFIG”
and press ENT. The CONFIG menu appears on the monitor screen.
CONF I G
ENHANCE : H IGH H F ILTER :AUTO DISPLAY : ON LANGUAGE
SELECT CANCEL
ENTER
MENU

Self-diagnosis Function

The unit has a self-diagnosis function. This function displays the monitor’s condition with the 1 indicator flashing and numbers on the SERVICE CODE indicator. The numbers inform you of the monitor’s current condition. When the unit is working properly, only the dot at the lower-right position on the SERVICE CODE indicator flashes. If the 1 indicator flashes, check the number and contact your authorized Sony dealer.
1 Check the two-digit number on the SERVICE
CODE indicator. The indicator shows one number, or multiple numbers alternately every a half second.
2 Unplug the unit.
Inform the number to your authorized Sony dealer.
26 (GB)
Operating a Specific Monitor
ON
ID MODE
SET
OFF

Operating a Specific Monitor with the Remote Commander

4 After necessary adjustment, press ID MODE OFF.
The monitor returns to the normal mode.
with the Remote Commander
Using the supplied Remote Commander, you can operate a specific monitor without affecting other monitors that are installed together.
1 Press ID MODE ON on the Remote Commander.
Monitor index numbers appear in white characters on all the monitors. (Every monitor is allocated an individual preset index number from 1 to 255.)
See “To change the index number” in the column to the right on this page to change the index number.
Index number
ON
SET
OFF
ID MODE
INDEX NO. 117 . . .
To change the index number
You can change the index number if necessary. When you change the number, use the buttons on the monitor.
1 Press MENU.
ON
SET
OFF
ID MODE
The main menu appears on the monitor screen.
MA IN MENU
PIC CONTROL PIC SIZE CONF I G MEMORY REMOTE STATUS
SELECT CANCEL
ENTER
MENU
2 Input the index number of the monitor you want to
operate using 0 – 9 buttons on the Remote Commander. The input number appears right next to each monitor’s own index number.
Input number
INDEX NO. 117 117
10/0
2
1 4 7
3
5
6
8
9
3 Press ID MODE SET.
The character on the selected monitor changes to cyan while others change to red.
2 Press M/m to move the cursor (B) to “REMOTE”
and press ENT. The REMOTE menu appears on the monitor screen.
REMOTE
INDEX NO. : 001 REMOT E MOD E : TV REMOTE ONLY : OFF
SELECT CANCEL
ENTER
MENU
3 Press M/m to move the cursor (B) to “INDEX
NO.” and press ENT. The following menu appears on the monitor screen.
INDEX NO. : 001
You can operate only a specified monitor. (All operations are available in ID mode except POWER ON/OFF.)
4 Select the index number with M/m and press ENT.
The menu returns to the REMOTE menu.
27 (GB)

Using the Other Remote Commander

Using the Other Remote Commander
The following operations can be controlled.
•Power on/off
•Input selection
•Menu operations
•Picture adjustments: contrast, phase and chroma
•On-screen display on/off (only for video monitors and TVs)
The available operations and the buttons to be used for each operation are limited depending on each Remote Commander. See the table below.
Remote Commander model RM-854 RM-1271 RM-PJ1292 RM-PJ1000 REMOTE MODE setting TV PJ PJ PJ
Input selection RGB1 RGB A A A
RGB2 B B B LINE LINE1 VIDEO VIDEO VIDEO
Menu operation MENU MENU PAGE or < PAGE or < MENU or <
ENTER ENTER ,,ENTER or , ++MMM ––mmm
Picture adjustment Contrast CONTRAST+/– CONTR+/– CONTR+/– CONTR+/–
Chroma CHROMA+/– COLOR+/– COLOR+/– COLOR+/– Phase PHASE+/– HUE+/– HUE+/– HUE+/–
On-screen information DISPLAY STATUS ON STATUS ON
28 (GB)

Specifications

Video processing
Capture range Horizontal rate: 15.6 to 80 kHz
Vertical rate: 48 to 120 Hz
Preset signal Input: 12 formats (See page
21 (GB))
Video memory 1,152 × 1,152 × 24 bits (RGB
total)
Sampling rate 14.3 to 50 MHz offset phase max.
(equivalent to 100 MHz sampling)
Panel system AC-type Plasma Display Panel Display resolution 1024 dots × 1024 lines Pixel pitch
Picture size
Panel size 42-inch (diagonal 1,058 mm)
0.90 (horizontal) × 0.51 (vertical)
(1⁄16 × 1⁄32 inches)
mm
921 (horizontal) × 522 (vertical)
(36 3⁄8 × 20 5⁄8 inches)
mm
Specifications
LINE (NTSC, PAL)
VIDEO IN BNC-type (×1)
Composite video, 1 Vp-p ±2 dB
sync negative, 75-ohm (automatic termination)
Y/C IN Mini DIN 4-pin type (×1)
Y (luminance): 1 Vp-p ±2 dB sync
negative, 75-ohm (automatic termination)
C (chrominance): Burst
0.286 Vp-p ±2 dB (NTSC), 75-ohm (automatic termination) Burst 0.3 Vp-p ±2 dB (PAL) 75-ohm (automatic termination)
AUDIO IN (L, R) Phono jack (×2)
500 mVrms, high impedance
VIDEO OUT BNC-type (×1) Loop-through Y/C OUT Mini DIN 4-pin type (×1) Loop-
through
AUDIO OUT (L, R) (Variable output)
Phono jack (×2) Loop-through
Inputs and Outputs
RGB1
R (R-Y)/ G (Y)/B (B-Y) IN
BNC-type (×3)
0.714 Vp-p/non-composite 75-ohm (automatic termination)
1 Vp-p/composite 75-ohm
(automatic termination)
SYNC IN(HD/COMP, VD)
BNC-type (×2) H (or composite) SYNC, V SYNC,
1 to 5 Vp-p high impedance
AUDIO IN (L, R) Phono jack (×2)
500 mVrms, high impedance
R (R-Y)/ G (Y)/B (B-Y) OUT
BNC-type (×3) Loop-through
SYNC OUT (HD/COMP, VD)
BNC-type (×2) Loop-through
H (or composite) SYNC, V SYNC
AUDIO OUT (L, R)
Phono jack (×2) Loop-through
RGB2
RGB IN D-sub 15-pin
See “Pin assignment” on page
30 (GB).
AUDIO IN (L, R) Phono jack (×2)
500 mVrms, high impedance
MONITOR OUT AUDIO (L, R)
Phono jack (×2) Maximum 500 mVrms, high
impedance
CONTROL S (IN, OUT)
Mini jack (stereo) (×2) 5 Vp-p
REMOTE (RS-232C)
Mini DIN 8-pin (×1)
SPEAKERS 6 to 16 ohms, 7 W + 7 W (when
the impedance is 8 ohms)
General
Power requirements
100 to 120 V AC, 50/60 Hz,
4.7 A/410 W
220 to 240 V AC, 50/60 Hz,
2.2 A/400 W
Operating conditions
Temperature: 0°C to 35°C (32°F to
95°F)
Humidity: 20% to 90% (no
condensation)
Atmospheric pressure: 700 to
1060 hPa
29 (GB)
Specifications
Storing/transporting conditions
Temperature: –10°C to +40°C
(14°F to 104°F)
Humidity: 20% to 90% (no
condensation)
Atmospheric pressure: 700 to
1060 hPa
Dimensions 1036 × 636 × 152 mm
(40 7⁄8 × 25 1⁄8 × 6 1⁄8 inches) (w/h/d)
Mass 45 kg (99 lb 3 oz) Supplied accessories
AC power cord (1) AC plug holder (1) Remote Commander RM-921 (1) Size AA (R6) batteries (2) Ferrite core (2) Foot support bracket (2) Screws for foot support bracket (6) Monitor stabilizer (2) Operating instructions (1)
Design and specifications are subject to change without notice.
RGB IN connector (D-sub 15-pin)
Pin No. Signal
1 Red video or R-Y 2 Green video or Y 3 Blue video or B-Y 4 Ground 5 Ground 6 Red ground 7 Green ground 8 Blue ground 9 Not used 10 Ground
Pin assignment
Y/C jack (Mini DIN 4-pin)
Chrominance
GND
11 Ground 12 SDA 13 H sync or composite sync 14 V sync 15 SCL
Luminance
GND
30 (GB)
Loading...
+ 154 hidden pages