Page 1
A-DV8-100-
11(1)
Additional Information for
Using Sony Wall-Mount Bracket (SU-WL100)
Compatible TV models for this Wall-Mount Bracket information:
NSX-24GT1
For product protection and safety reasons, Sony strongly recommends that you use the
Wall-Mount Bracket model designed for your TV and that the wall-mounting of your TV
is performed by Sony dealers or licensed contractors.
To Customers
Please provide your licensed contractor with this installation supplement as well as the instructions
(supplied with the SU-WL100 Wall-Mount Bracket). Read these documents carefully for safety and proper
installation.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required in installing this product, especially to determine the strength
of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product
to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during
the installation. Sony is not liable for any damage or injury caused by mishandling or improper
installation.
For proper installation, follow your wall-mount bracket instructions and the directions below.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 1 −
Page 2
Installing the Wall-Mount Bracket
Install the Base Plate and Mounting Hooks.
1 Open the Wall-Mount Bracket package and check for all the required parts
along with the Instructions.
2 Adjust the position of the holders of the Base Plate.
Refer to the Instructions for SU-WL100.
3 Decide where you want to install your TV. Refer to the TV installation
dimensions table.
Dimension Table
Screen center point
Unit: inches (mm)
Model Name
NSX-24GT1
Figures in the above table may dier slightly depending on the installation.
Display
dimensions
22 1/2
(571)
14
(354)
Screen center
dimensions
1 7/8
(49)
Length for each mounting angle
Angle (0°) Angle (20°)
8 7/8
(227)
5 1/8
(131)
9 5/8
(243)
13 1/8
(334)
9 1/8
(233)
CAUTION
e wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV.
Refer to your TV’s operating instructions for its weight.
4 Install the Base Plate on the wall.
Refer to the Instructions for SU-WL100.
5 Disconnect all the cables from the TV.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 2 −
Page 3
6 Remove the Cable cover from the rear of the TV. Then remove the screws and
detach the Table-Top Stand from the TV.
Place the TV with its screen facing down on a stable cloth-covered work surface.
Soft cloth
7 Attach the VESA Plate.
Secure it to the TV using three screws (removed according to Step 6).
Screw
(supplied with TV NSX-24GT1)
VESA Plate
(supplied with TV NSX-24GT1)
Soft cloth
8 Secure the Mounting Hook to the left side of the rear of the TV.
Secure it to the TV using two screws (supplied with SU-WL100).
Screw
(+PSW4 × 12)
Mounting Hook
Soft cloth
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 3 −
Page 4
9 Adjust the angle of the Mounting Hook.
Refer to the Instructions for SU-WL100.
10 Secure the Mounting Hook to the right side of the rear of the TV.
Refer to the Instructions for SU-WL100.
Secure it to the TV using two screws (supplied with SU-WL100).
Hook Locations Diagram/Table
Model Name Hook Location
NSX-24GT1 b
Hook Location
When installing the TV onto the Base Bracket.
a*
b
* Hook position “a” cannot be used for the
models in the table above.
11 Install the TV on the Wall.
Refer to the Instructions for SU-WL100.
Connect the cables to the corresponding inputs on the rear of the TV.
For details on the cable connection, refer to the Operating Instructions for your TV.
Install the TV onto the Base Plate.
Be sure to secure the TV to the Base Plate.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 4 −
Loading...