Sony MEX-DV90, MEX-DV90EE, MEX-DV900 Schematic
MEX-DV90/DV90EE/DV900
SERVICE MANUAL
Ver. 1.0 2007.12
Photo: MEX-DV900
Manufactured under license
from Dolby Laboratories.
symbol are trademarks of Dolby Laboratories.
Corporation in the United States and/or other
countries.
“DVD VIDEO,” “DVD-R,” “DVD-RW,”
“DVD+R,” and “DVD+RW” are trademarks.
THIS PRODUCT IS LICENSED UNDER THE
MPEG-4 VISUAL PATENT PORTFOLIO
LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER FOR
DECODING MPEG-4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM
A VIDEO PROVIDER LICENSED BY MPEG
LA TO PROVIDE MPEG-4 VIDEO. NO
LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION INCLUDING
THAT RELATING TO PROMOTIONAL,
INTERNAL AND COMMERCIAL USES AND
LICENSING MAY BE OBTAINED FROM
MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM
“Dolby” and the double-D
Microsoft, Windows Media,
and the Windows logo are
trademarks or registered
trademarks of Microsoft
“DivX” and “DivX Certified” are
registered trademarks or trademarks
of DivX, Inc.
– Except Chinese model –
System
Laser: Semiconductor laser
Signal format system: PAL (Except E model)
PAL/NTSC Switchable
(E and Indian models)
DVD/CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wowand flutter: Below measurable limit
Harmonic distortion: 0.01 %
Tuner section
FM
Tuning range:
AEP and UK models: 87.5– 108.0 MHz
Russian model:
FM1/FM2: 87.5 – 108.0 MHz (at50 kHz step)
FM3: 65 – 74 MHz (at30 kHz step)
Asian model: 87.5– 108.0 MHz (at 50 kHz step)
LatinAmericanmodel:
87.5 – 107.9 MHz (at200 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 k Hz: 0.5 % (stereo),
0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
AM (E and Indian models)
Tuning range:
Asian model:
531 – 1,602 kHz (at 9 kHz step)
Latin American model:
530 – 1,710 kHz (at 10 kHz step)
AEP Model
UK Model
E Model
MEX-DV900
Chinese Model
MEX-DV90
Russian Model
MEX-DV90EE
Model Name Using Similar Mechanism NEW
Mechanism Type MG-612L-187
Optical Pick-up Name KHS-360A
SPECIFICATIONS
Antenna (aerial) terminal: External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: 30 μV
MW/LW (AEP, Russian and UK models)
Tuning range:
MW: 531 – 1,602kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal: External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: MW: 30 μV, LW: 4 0 μV
Power amplifier section
Outputs: Speaker outputs (sure sealconnectors)
Speaker impedance: 4–8ohms
Maximum power output: 52 W × 4(at4ohms)
General
Outputs:
Video output terminal
Rear audiooutput terminals
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
AUX audio input terminals
Antenna (aerial) input terminal
Parking break control terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at1 kHz (XPLOD)
Hi: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 180 mm
1
(7
/8 × 2 × 71/8 in) (w/h/d)
Mounting dimensions: Approx. 182 × 53 × 163 mm
1
(7
/4 × 21/8 × 61/2 in) (w/h/d)
– Continued on next page –
9-887-927-01
2007L05-1
2007.12
©
MULTI DISC PLAYER
Sony Corporation
Audio Business Group
Published by Sony Techno Create Corporation
MEX-DV90/DV90EE/DV900
Mass: Approx. 1.4 kg (3 lb 2 oz)
Supplied accessories:
Card remote commander: RM-X168
Parts for installationand connections(1 set)
Your dealer may nothandlesome of the abovelistedaccessories.
Please ask the dealer for detailed information.
US and foreign patents licensed from Dolby Laboratories.
MPEG Layer-3 audio coding technology and patents licensed from
Fraunhofer IIS and Thomson.
DivX, DivX Certified, and associatedlogos are trademarks of DivX, Inc.
and are used under license.
This product is protected by certain intellectual property rights of
Microsoft Corporation. Use or distribution of such technology outside of
this product is prohibited without a license from Microsoft or an
authorized Microsoft subsidiary.
Design and specifications are subject to change without notice.
– Chinese model –
DVD/CD Player section
Frequency response: 20 Hz – 20,000 Hz (±2 dB)
Tuner section
FM
Tuning range: 87.5 MHz – 108.0 MHz
Antenna (aerial) terminal:
Intermediatefrequency: 10.7 MHz/450 kHz
AM
Tuning range: 531 kHz – 1,602 kHz
Antenna (aerial) terminal:
Intermediatefrequency: 10.7 MHz/450 kHz
External antenna (aerial) connector
External antenna (aerial) connector
Power amplifier section
Outputs: Speaker outputs(sure sealconnectors)
Speaker impedance: 4ohms–8ohms
Maximum power output: 50 W per cha nne l (1 kHz, 16 V, 4 ohms)
General
Outputs:
Videooutput terminal
Rear audiooutput terminals
Power antenna (aerial) relay control terminal
Poweramplifier control terminal
Inputs:
AUXaudio input terminals
Antenna (aerial) input terminal
Parking break control terminal
AUXinput jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at1 kHz (XPLOD)
Hi: ±10dBat10kHz(XPLOD)
Power requirements: 12 V DC car battery
(negativeground (earth))
Power supply voltage: 11 V – 16 V
Dimensions: Approx. 178mm × 50 mm × 180 mm
1
(7
/8 in × 2in× 71/8 in) (w/h/d)
Mounting dimensions:
Approx. 182 mm × 53 mm × 163 mm
1
/4 in × 21/8 in × 61/2 in) (w/h/d)
(7
Mass: Approx. 1.4 kg (3 lb 2 oz)
Supplied accessories:
Card remote commander:RM-X168
Parts for installationand connections(1 set)
Your dealer may not handle some of the above listed accessories.
Please ask the dealer for detailed information.
US and foreign patents licensed from Dolby Laboratories.
MPEG Layer-3 audio coding technology and patents licensed from
Fraunhofer IIS and Thomson.
DivX, DivX Certified, and associated logo s are tradem a rks of DivX, Inc.
and are used under license.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specifi ed herein may result in hazardous radiation exposure.
This label is located on the bottom of the
chassis.
CAUTION
RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
:
CLASS 1M VISIBLE/INVISIBLE LASER
This label is located on the drive unit’s internal
chassis.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
This product is protected by certain intellectual property rights of
Microsoft Corporation. Use or distribution of such technology outside of
this product is prohibited without a license from Microsoft or an
authorized Microsoft subsidiary.
Design and specifications are subject to change without notice.
2
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 4
2. GENERAL .................................................................. 7
3. DISASSEMBLY
3-1. Disassembly Flow .......................................................... 13
3-2. Sub Panel Complete Assy ............................................... 13
3-3. DVD Mechanism Deck Block ........................................ 14
3-4. DC Fan (25X25) (M901), MAIN Board ........................ 14
3-5. SENSOR Board, Chassis (T612Z) Sub Assy .................. 15
3-6. Chassis (OP, Z) Complete Assy ...................................... 15
3-7. SERVO Board ................................................................ 16
4. ELECTRICAL CHECK ......................................... 17
5. DIAGRAMS
5-1. Block Diagram - SERVO/VIDEO Section - ................... 19
5-2. Block Diagram - TUNER/AUDIO Section - .................. 20
5-3. Block Diagram
- PANEL/POWER SUPPLY Section - ............................ 21
5-4. Schematic Diagram - SERVO Section (1/3) - ................. 23
5-5. Schematic Diagram - SERVO Section (2/3) - ................. 24
5-6. Schematic Diagram - SERVO Section (3/3) - ................. 25
5-7. Printed Wiring Board - SERVO Section (1/2) - .............. 26
5-8. Printed Wiring Boards - SERVO Section (2/2) - ............ 27
5-9. Schematic Diagram - MAIN Board (1/2) - ..................... 28
5-10. Schematic Diagram - MAIN Board (2/2) - ..................... 29
5-11. Printed Wiring Board - MAIN Board - ........................... 30
5-12. Printed Wiring Board - KEY Board -.............................. 31
5-13. Schematic Diagram - KEY Board - ................................ 32
MEX-DV90/DV90EE/DV900
6. EXPLODED VIEWS
6-1. Main Section ................................................................... 46
6-2. Front Panel Section ......................................................... 47
6-3. DVD Mechanism Deck Section (MG-612L-187) .......... 48
7. ELECTRICAL PARTS LIST .............................. 49
3
MEX-DV90/DV90EE/DV900
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTE ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in tha optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
MODEL IDENTIFICATION
– Bottom View –
Region Code
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE THE IC4 ON THE SERVO BOARD
REPLACING
IC4 cannot exchange with single. When IC4 is damaged, exchange
the entire mounted board.
NOTE THE IC503 ON THE MAIN BOARD
REPLACING
IC503 cannot exchange with single. When IC503 is damaged, exchange the entire mounted board.
Part No.
Label indication
Signal format Region
system code
PAL 2 3-283-924-0[] DV900: AEP and UK models
PAL 3 3-283-920-0[] DV900: E (PAL) model
NTSC 4 3-283-921-0[] DV900: E (NTSC) model
PAL 5 3-283-922-0[] DV900: Indian model
PAL 5 3-283-925-0[] DV90EE: Russian model
PAL 6 3-283-923-0[] DV90: Chinese model
Destination
Part No.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable) as shown below.
• Connect the MAIN board (CN101) and the SERVO board (CN3) with the extension cable (Part No. J-2506-062-1).
MAIN BOARD
(CN101)
J-2506-062-1
SERVO BOARD
(CN3)
4
MEX-DV90/DV90EE/DV900
NOTE FOR FLEXIBLE BOARD OF THE OPTICAL
PICK-UP
When connecting or disconnecting the fl exible board of the opti-
cal pick-up to or from the CN2 of the SERVO board, follow the
procedure given below.
Note: When soldering the short lands, solder within 5 seconds at the
temperature of soldering iron below 300°C.
Disconnection:
1. Solder two shortland.
2. Disconnect the fl exible board from the CN2 of the SERVO
board.
Connection:
1. Connect the fl exible board to the CN2 of the SERVO board.
2. Unsolder two shortland.
NOTE FOR REPLACING THE MOUNTED MAIN
BOARD
If the mounted MAIN board was replaced, be sure refer to Technical News published separately.
Playable discs and symbols used in this manual
This unit can play various video/audio discs.
The following chart helpsyou to check i f a disc issupporte d by this
unit, as well as what functions ar e available fora given disc type.
Disc symbol
in manual
VIDEO
Disc format Disc logo
DVD VIDEO
1
DVD-R*
DVD-R DL*
1
(Video mode/VR mode)
DVD-RW*
1
(Video mode/VR mode)
DVD+R*
DVD+R DL*
DVD+RW*
1
1
1
Video CD
(Ver. 1.0/1.1/ 2. 0)
NOTE FOR REPLACEMENT OF THE AUX JACK
(J901)
To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
AUX jack
Audio CD
CD-ROM*
CD-R*
AUDIO
CD-RW*
*1 Audio files can also be stored.
*2 Video/image files can also be stored.
Note
“DVD” may be used in this manual as a general term for DVD VIDEOs,
DVD-Rs/DVD-RWs, and DVD+Rs/DVD+RWs.
2
2
2
front panel
5
MEX-DV90/DV90EE/DV900
The following chartshows the supported compression formats,their file types, and the disc types on whichthose files can be stored.
Availabl e functions differ depending on the format, regardl essof disc type. The format symbols below appearnext to the description o f functions
available for that format.
Format symbol in manual File type Storable disc type
MP3 audio file
WMA audio file
JPEG image file
®
DivX
video file
Unsupported discs
The following discs cannot be playedon this unit.
•8cm(3
•12cm (4
• CD-ROM containing files otherthan MP3/WMA/JPEG/DivX
•SA-CD
•CD-G
•Photo-CD
• VSD (Video Single Disc)
• DVD-ROM containing files otherthan MP3/WMA/JPEG/DivX
•DVD-RAM
•DVD-Audio
• Ac tive-Audio (Data)
• SVCD (Super Video CD)
•CDV
• Discs created in Packet Write format
• Discs in DTS format
Note
Even compatib lediscs may notbe playable on this unit, dependingon their recorded condition.
1
/4 in) discs
3
/4 in) discs utilizing only the inner 8 cm (31/4 in) data portion (the rest is transparent)
DATA DVDs
DVD-ROM
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DAT A CDs
CD-ROM
CD-R
CD-RW
Region code
The region syst em is used to prot ectsoftware copyrights.
The region code is located on the bottom of the unit, and only DVDs labeled with an identicalregion code can
played on this unit.
DVDs labeled can also be played.
If you try to play any other DVD, the message “Playback p rohibitedby regio n code.” will appear on the monitor
screen. Depe ndi ng on the DVD, no region code may be labeled even thou gh playing the DVD is prohibited by area
restrictions.
ALL
Region code
6
(DV90/DV900: E and Indian models)
R
R
R
Location and function of controls
Main unit
OFF
SEEK
BACK
BROWSE
DSPL
PUSH SOUND/ENTER
SOURCE
SEEK
MODE
SCRL
1 2
SHUF
MUBLAPER
3 4 56
SECTION 2
GENERAL
AUX
MEX-DV90/DV90EE/DV900
0 Number buttons
Disc:
: C REP
: SHUF #
/: ALBUM –/+ (7/W)
Toskip an album or folder/move t he
cursor (press);skipalbumsorfolders
continuously (press andhold).
: V (play/pause)
Tostart/pause playback.
Radio:
Toreceivestored stations (press);store
stations(pressandhold).
1 Receptor for the card remote
commander
*1 When a CD/MP3/WMA/JPEG/DivX is played.
*2 Operation differs depending on the disc.
*3 When two auxiliarydevicesareused.
This section is extracted
from instruction manual.
BRTRERG
Instructions in this manual generallydescribethe
controls on the card remote commander. You can
also use the controls on the main unit if theyhave
the same or similar names to those on the card
remote commander.
" OFF button
Topoweroff/stopthesource(press); shut off
completely (pressand hold).
# (BROWSE) button
Toenter the Quick-BrowZermode.*
$ Volume control dial/SOUND/ENTER
button
Toadjustthevolume/adjustasetting(rotate);
open the sound menu/apply a setting (press);
open the system setup menu (press and
hold).
% SOURCE button
Topoweron; change the source (Radio/Disc/
AUX).
& Disc slot
Toinsert the disc.
' Display window
( AUX input jack
Toconnect a portable audio device.
1
Card remote commander RM-X168
Remove the insulation film beforeuse.
" OFF button
Topoweroff/stopthesource(press); shut off
completely (pressand hold).
# SOUND button
Toopen the sound menu.
$ VISUAL SETUP button
Toopen the play mode/visual setup menu.
H
) ;(eject) button
Toeject the disc.
* (front panel release) button
+ (BACK/DSPL) button
Toreturn to the previous display;changethe
displayitem.
, SEEK –/+ buttons
Disc:
Toskip a chapter/track/scene/file(press);
reverse/fast-forward disc (pressandhold
momentarily);reverse/fast-forward track
(press and hold).*
Radio:
Totuneinstationsautomatically(press);find
a station manually (pressandhold).
- MODE button
Toselect the radio band (FM / A M); selectan
auxiliary device*
. SCRL (Scroll) button
To scroll the display item.
/ RESET button
I
2
3
.
RB
RT
RE
RG
RH
RI
RK
% SYSTEM SETUPbutton
Toopenthesystem setupmenu.
& (BACK)/0 button
Toreturn to the previous display; return to
the menu on a VCD*
1
.
' Number buttons
Disc:
Tolocate a title/chapter/track.
Radio:
Toreceive stored stations (press);store
stations(pressandhold).
( CLEAR button
Todelete an entered number.
) DSPL(Display) button
Tochange display items.
* ATT (Attenuate) button
Toattenuate the sound (to cancel, press
again).
+ V (Play/Pause)button
Tostart/pause playback.
, N/. buttons
Disc:
Toskipachapter/track/scene/file (press);
reverse/fast-forward disc (pressandhold
momentarily);reverse/fast-forward track
(press and hold).*
Radio:
Totune in stationsautomatically(press); find
a station manually (pressandhold).
- DVD playback setting buttons
"6%*0:
Tochange the audio language/format.
(For VCD/CD/MP3/WMA , to change the
audio channel.)
46#5*5-&:
Tochange the subtitle language.
"/(-&:
Tochange the viewing angle.
501.&/6:
Toopen the top menu on a DVD.
.&/6:
Toopen the menu on a disc.
. (BROWSE)button
Toenter theQuick-BrowZer mode.*
/ /./N/ (Cursor)/ENTER buttons
To movethecursor andapplyasetting.
0 SRC (Source) button
Topoweron;changethesource(Radio/Disc/
AUX).
2
3
1 MO DE button
Toselect the radio band (FM/AM); select an
auxiliary device*
2 VOL (Volume) +/– buttons
Toadjustthevolume.
*1 When playing with PBC function.
*2 Operationdiffers dependingonthedisc.
*3 When a CD/MP3/WMA/JPEG/DivX is played.
*4 When two auxiliary devices are used.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless4063$& on the main unit is pressed, or a
disc is inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander”.
4
.
7
MEX-DV90/DV90EE/DV900
R
R
R
(DV90EE/DV900: AEP and UK models)
Location and function of controls
Main unit
OFF
BROWSE
SEEK
BACK
DSPL
Instructionsinthismanual generally describethe
controls on the card remote commander. You can
also use the controls on the main unit if theyhave
the same or similar names to those on the card
remote commander.
" OFF button
Topoweroff/stopthesource(press); shut off
completely (pressand hold).
# (BROWSE) button
Toenterthe Quick-BrowZer mode.*
$ Volume control dial/SOUND/ENTER
button
Toadjustthev olume/adjustasetting(rotate);
open the sound menu/apply a setting(press);
open the system setup menu (press and
hold).
% SOURCE button
Topoweron; change the source (Radio/Disc/
AUX).
& Disc slot
Toinsert the disc.
' Display window
PUSH SOUND/ENTER
SOURCE
SEEK
MODE
PTY
AF/TA
BRTRERG
REP
1 2
ALBUM
SHUF
3 4 56
H
( AUX input jack
Toconnect a portable audio device.
) ;(eject) button
To eject the disc.
* (front panel release) button
+ (BACK/DSPL) button
Toreturn to the previous display;changethe
1
display item.
, SEEK –/+ buttons
Disc:
Toskip a chapter/track/scene/file(press);
reverse/fast-forward disc (press and hold
momentarily); reverse/fast-forwardtrack
(press and hold).*
Radio:
Totuneinstationsautomatically(press);find
a station manually (pressandhold).
- MODE button
Toselect theradio b and (FM/MW/LW);
selectanauxiliarydevice*
. AF (Alternative Frequencies)/
TA (Traffic Announcement)/
PTY (Program Type) button
Toset AF and TA (press); select PTY(press
and hold) inRDS.
/ RESET button
0 Number buttons
Disc:
: C REP
: SHUF #
AUX
I
2
3
.
/: ALBUM –/+ (7/W)
Toskip an album or folder/move t he
cursor (press); skip albums or folders
continuously (press andhold).
: V (play/pause)
Tostart/pause playback.
Radio:
Toreceivestored stations (press);store
stations(pressandhold).
1 Receptor for the card remote
commander
*1 When a CD/MP3/WMA/JPEG/DivX is played.
*2 Operation differs depending on the disc.
*3 When two auxiliarydevicesareused.
Card remote commander RM-X168
Remove the insulation film beforeuse.
" OFF button
Topoweroff/stopthesource(press); shut off
completely (pressand hold).
# SOUND button
Toopen the sound menu.
$ VISUAL SETUP button
Toopen the play mode/visual setup menu.
RB
RT
RE
RG
RH
RI
RK
% SYSTEM SETUPbutton
Toopenthesystem setupmenu.
& (BACK)/0 button
Toreturn to the previous display; return to
the menu on a VCD*
1
.
' Number buttons
Disc:
Tolocate a title/chapter/track.
Radio:
Toreceivestored stations (press);store
stations(pressandhold).
( CLEAR button 28, 31
Todelete an entered number.
) DSPL(Display) button
Tochange display items.
* ATT (Attenuate) button
Toattenuate the sound (to cancel, press
again).
+ V (Play/Pause)button
Tostart/pause playback.
, N/. buttons
Disc:
Toskipachapter/track/scene/file (press);
reverse/fast-forward disc (pressandhold
momentarily);reverse/fast-forward track
(press and hold).*
Radio:
Totune in stationsautomatically(press); find
a station manually(pressand hold).
- DVD playback setting buttons
"6%*0:
Tochange the audio language/format.
(For VCD/CD/MP3/WMA , to change the
audio channel.)
46#5*5-&:
Tochange the subtitle language.
"/(-&:
Tochange the viewing angle.
501.&/6:
Toopen the top menu on a DVD.
.&/6:
Toopen the menu on a disc.
. (BROWSE)button
Toenter theQuick-BrowZer mode.*
/ /./N/ (Cursor)/ENTER buttons
To movethecursor andapplyasetting.
0 SRC (Source) button
Topoweron;changethesource(Radio/Disc/
AUX).
2
3
1 MO DE button
Toselect the radio band (FM/MW /LW);
selectan auxiliarydevice*
2 VOL (Volume) +/– buttons
Toadjustthevolume.
*1 When playing with PBC function.
*2 Operationdiffersdependingon the disc.
*3 Whena CD/MP3/WMA/JPEG/DivXisplayed.
*4 When two auxiliary devices are used.
Note
If the unit isturned off and the displaydisappears, it
cannotbeoperated with the cardremote commander
unless4063$& on the main unit is pressed, or a
disc is inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander”.
4
.
8
(DV90/DV900: E and Indian models)
VIDEO OUT
REAR AUDIO OUT
VIDEO OUT
L
R
AUX
IN
VIDEO
OUT
AUX IN
REAR AUDIO OUT
VIDEO OUT
A
Monitor*
Monitor*
ⲥ㾚఼*
* not supplied
no suministrado
䴲䰘䗕
B
Monitor*
Monitor*
ⲥ㾚఼*
* not supplied
no suministrado
䴲䰘䗕
MEX-DV90/DV90EE/DV900
Cautions
• This unit is designed for negative ground (earth) 12V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list
• The numbers in the list are keyed to those in the
instructions.
• The bracket and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys to remove the bracket
and the protection collar from the unit. For
details, see “Removing the protection collar and the
bracket ()” on the reverse side of the sheet.
• Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Note
Before installing, make sure that the catches on both sides of
the bracket are bent inwards 2 mm (
straight or bent outwards, the unit will not be installed securely
and may spring out.
Connection example
Notes (-B)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Catch
3
/32 in). If the catches are
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply
leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
To the +12V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply
leads.”
To the +12V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
To the parking brake switch cord
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster.For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left
speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Notes on connection
• If speaker and amplifier are not connected correctly,“FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
• If you are to use the monitor for the rear seats, connect the
parking brake switch cord to the ground (earth).
Left
Izquierdo
Ꮊ
Right
Derecho
ে
Left
Izquierdo
Ꮊ
Right
Derecho
ে
Monitor (not supplied)
Monitor (no suministrado)
ⲥ㾚఼䴲䰘䗕
1
*
from car antenna (aerial)
desde la antena del automóvil
ᴹ㞾≑䔺㒓
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
᳔⬉⌕$
*1RCA pin cord (not supplied)
2
*
For details on connecting to the parking
brake switch cord, see“Connecting the
parking brake cord ()” on the reverse
side.
3
*
Auxiliary device such as hideaway
navigation device,TV tuner box, etc.
Fuse (10 A)
Fusible (10 A)
ֱ䰽ϱ$
Blue/white striped
Con rayas azules y blancas
㪱㡆ˋⱑ㡆ᴵ㒍
White
Blanco
ⱑ㡆
White/black striped
Con rayas blancas y negras
ⱑ㡆ˋ咥㡆ᴵ㒍
Gray
Gris
♄㡆
Gray/black striped
Con rayas grises y negras
♄㡆ˋ咥㡆ᴵ㒍
Green
Verde
㓓㡆
Green/black striped
Con rayas verdes y negras
㓓㡆ˋ咥㡆ᴵ㒍
Purple
Morado
㋿㡆
Purple/black striped
Con rayas moradas y negras
㋿㡆ˋ咥㡆ᴵ㒍
1
*
Cable con terminales RCA
(no suministrado)
2
*
Para obtener detalles acerca de cómo
conectar el cable de conmutación del
freno de estacionamiento, consulte
“Conexión del cable del freno de
estacionamiento ()” en el dorso.
3
*
Dispositivo auxiliar como, por
ejemplo, un dispositivo de navegación
independiente, un sintonizador de
televisión, etc.
Black
Negro
咥㡆
Blue
Azul
㪱㡆
Red
Rojo
㑶㡆
Yell ow
Amarillo
咘㡆
Light green
Verde claro
⎵㓓㡆
1
*
5&$䩜ᇐ㒓˄䴲䰘䗕˅
2
*
᳝݇䖲㟇ذ䔺ࠊࡼᓔ݇ᇐ㒓ⱘ䆺㒚䇈
ᯢˈ䇋খ䯙ড䴶ⱘĀ䖲ذ䔺ࠊࡼ⬉㒓
˄˅āDŽ
3
*
՟བ䱤㮣ᓣᇐ㟾䆒ǃ79䇗䇤Ⲧㄝ䕙ࡽ
䆒DŽ
3
*
ANT REM
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
᳔⬉⌕ $
PARKING BRAKE
2
*
9
MEX-DV90/DV90EE/DV900
182 mm
53 mm
Foot brake type
Tipo de freno de pedal
㛮ࠊࡼൟ
Parking brake switch cord
Cable de conmutación del
freno de estacionamiento
ذ䔺ࠊࡼᓔ݇⬉㒓
12
Hand brake type
Tipo de freno manual
ࠊࡼൟ
Face the hook
inwards.
El gancho debe
encontrarse en la
parte interior.
䩽ᄤ䴶ݙDŽ
Parking brake switch cord
Cable de conmutación del
freno de estacionamiento
ذ䔺ࠊࡼᓔ݇⬉㒓
Orient the release key
correctly.
Oriente la llave de
liberación en la
dirección correcta.
ℷ⹂⹂ᅮᓔ䫕䩹࣭ᮍDŽ
12 3
Dashboard
Tabl ero
Ҿ㸼ᵓ
Claws
Uñas
⟾
Fire wall
Cortafuegos
䰆☿ຕ
A TOY OT A
max. size
5 × 8 mm
7
/32 ×11/32 in)
(
Tamaño máx.
5 × 8 mm
᳔ሎᇌ
hPP
to dashboard/center console
al tablero o consola central
㟇Ҿ㸼ᵓЁ༂ࠊㆅ
Bracket
Soporte
ᠬᶊ
Bracket
Soporte
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
䱣≑䔺䰘䗕ⱘ⦄᳝䚼ӊ
ᠬᶊ
max. size
5 × 8 mm
7
/32 ×11/32 in)
(
Tamaño máx.
5 × 8 mm
᳔ሎᇌ
hPP
B NISSAN
max. size
5 × 8 mm
7
/32 ×11/32 in)
(
Tamaño máx.
5 × 8 mm
᳔ሎᇌ
hPP
Bracket
Soporte
ᠬᶊ
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
䱣≑䔺䰘䗕ⱘ⦄᳝䚼ӊ
AB
Precautions
• Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe
and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake
cord
Be sure to connect the parking cord (Light green) of
to the parking brake switch cord. The mounting position
of the parking brake switch cord depends on your car.
Consult your car dealer or your nearest Sony dealer for
further details.
10
Removing the protection collar
and the bracket
Before installing the unit, remove the protection
collar and the bracket from the unit.
1 Remove the protection collar .
Engage the release keys together with the
protection collar
Pull out the release keys to remove the
protection collar
2 Remove the bracket.
Insert both release keys together between
the unit and the bracket
Pull down the bracket
to separate.
.
.
until they click.
, then pull up the unit
Mounting example
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if necessary (-2).
• Make sure that the 4 catches on the protection collar are
properly engaged in the slots of the unit (-3).
Mounting the unit in a Japanese
car
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws .
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-ATo detach
Before detaching the front panel, be sure to press .
, and pull it off towards you.
Press
-BTo attach
Engage part of the front panel with part of the unit,
as illustrated, and push the left side into position until it
clicks.
to dashboard/center console
al tablero o consola central
㟇Ҿ㸼ᵓЁ༂ࠊㆅ
max. size
5 × 8 mm
7
/32 ×11/32 in)
(
Tamaño máx.
5 × 8 mm
᳔ሎᇌ
hPP
Bracket
Soporte
ᠬᶊ
Warning if your car’s ignition
has no ACC position
Be sure to set theAuto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in
the set time after the unit is turned off, which prevents
battery drain.
If you do not set theAuto Off function, press and hold
until the display disappears each time you turn
the ignition off.
RESET button
When the installation and connections are completed,
be sure to press the RESET button with a ball-point pen,
etc., after detaching the front panel.
(DV90EE/DV900: AEP and UK models)
A
Moniteur
* not supplied
nicht mitgeliefert
non fourni
non in dotazione
niet bijgeleverd
Monitor (not supplied)
Monitor (nicht mitgeliefert)
Moniteur (non fourni)
Monitor (non in dotazione)
Monitor (niet bijgeleverd)
2
*
REAR AUDIO OUT
1
*
from car antenna (aerial)
von Autoantenne
de l’antenne de la voiture
dall’antenna dell’auto
van een auto-antenne
Max. supply current 0.3 A
max.Versorgungsstrom 0,3 A
Courant d’alimentation maximum 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
Cautions
• This unit is designed for negative ground (earth) 12 V DC operation only.
• Do not get the leads under a screw, or caught in moving parts (e.g. seat railing).
• Before making connections, turn the car ignition off to avoid short circuits.
• Connect the power supply lead to the unit and speakers before connecting it to the
auxiliary power connector.
• Run all ground (earth) leads to a common ground (earth) point.
• Be sure to insulate any loose unconnected leads with electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other stereo components, the connected
car circuit’s rating must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect the unit directly to the battery.
Parts list
• The numbers in the list are keyed to those in the instructions.
• The bracket and the protection collar are attached to the unit before shipping.
Before mounting the unit, use the release keys to remove the bracket and the
protection collar from the unit. For details, see “Removing the protection collar and
the bracket ()” on the reverse side of the sheet.
• Keep the release keys for future use as they are also necessary if you
remove the unit from your car.
Monitor*
Monitor*
Monitor*
Monitor*
VIDEO OUT
*
AMP REM
PARKING BRAKE
3
*
VIDEO
OUT
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
Light green
Hellgrün
Vert cl air
Verde chiaro
Lichtgroen
See “Power connection diagram” on the reverse side for details.
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern
Sie dazu bitte um.
Voir le « Schéma de raccordement d’alimentation » au verso pour
plus de détails.
Per ulteriori informazioni, vedere“Diagramma dei collegamenti di
alimentazione” che si trova sul retro.
Zie "Voedingsaansluitschema" op de achterkantvoor meer details.
B
*1Note for the antenna (aerial) connecting
If your car antenna (aerial) is an ISO (International
Organization for Standardization) type, use the supplied
adaptor to connect it. First connect the car antenna
(aerial) to the supplied adaptor, then connect it to the
antenna (aerial) jack of the master unit.
2
*
RCA pin cord (not supplied)
3
*
For details on connecting to the parking brake switch cord,
see “Connecting the parking brake cord ()” on the reverse
side.
4
*
Auxiliary device such as hideaway navigation device,TV
tuner box, etc.
1
*
Hinweis zum Anschließen der Antenne
Wenn Ihre Fahrzeugantenne der ISO-Norm (Internationale
Normungsgemeinschaft) entspricht, schließen Sie sie mithilfe
des mitgelieferten Adapters an.Verbinden Sie zuerst
die Fahrzeugantenne mit dem mitgelieferten Adapter und
verbinden Sie diesen dann mit der Antennenbuchse des
Hauptgeräts.
2
*
Cinchkabel (nicht mitgeliefert)
3
Informationen zum Anschließen der
*
Parkbremsenschaltleitung finden Sie unter „Anschließen der
Parkbremsenleitung ()“ auf der Rückseite.
VIDEO OUT
L
R
AUX
IN
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
Caution
Handle the bracket carefully to avoid injuring your fingers.
Note
Before installing, make sure that the catches on both sides of the bracket are bent inwards 2 mm
3
(
/32 in). If the catches are straight or bent outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-B)
• Be sure to connect the ground (earth) lead before connecting the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Connection diagram
To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting any other system may damage the unit.
To the parking brake switch cord
AUX IN
Catch
from the car’s speaker connector
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore del diffusore dell’auto
van de autoluidsprekeraansluiting
1
2–
3
4–
Negative polarity positions 2, 4, 6 and 8 have striped leads.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
from the car’s power connector
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsaansluiting
4
5
Positions 1, 2, 3 and 6 do not have pins.
An Position 1, 2, 3 und 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
* not supplied
nicht mitgeliefert
non fourni
non in dotazione
niet bijgeleverd
Purple
Violett
Mauve
Viola
Paars
Gray
Grau
Gris
Grigio
Grijs
Yell ow
Gelb
Jaune
Giallo
Geel
Blue
Blau
Bleu
Blu
Blauw
Monitor*
Monitor*
Moniteur
Monitor*
Monitor*
+
+
MEX-DV90/DV90EE/DV900
VIDEO OUT
*
REAR AUDIO OUT
4
*
Zusätzliches Gerät wie ein verstecktes Navigationsgerät, ein
Fernsehtuner usw.
1
*
Remarque sur le raccordement de l’antenne
Si votre antenne de voiture est de type ISO (Organisation
internationale de normalisation), utilisez l’adaptateur fourni
pour la raccorder. Raccordez d’abord l’antenne de voiture
à l’adaptateur fourni et, ensuite, à la prise d’antenne de
l’appareil principal.
2
*
Cordon à broche RCA (non fourni)
3
*
Pour plus de détails sur le raccordement du cordon
du capteur du frein à main, reportez-vous à la section
« Raccordement du cordon du frein à main () » au verso.
4
*
Appareil auxiliaire comme un appareil de navigation
dissimulé, un tunerTV, etc.
1
*
Nota per il collegamento dell’antenna
Se l’antenna dell’auto è di tipo ISO (International
Organization for Standardization), utilizzare l’adattatore
in dotazione per collegarla. Collegare prima l’antenna della
macchina all’adattatore in dotazione, quindi collegarla alla
presa dell’antenna dell’apparecchio principale.
2
*
Cavo a piedini RCA (non in dotazione)
3
*
Per ulteriori informazioni sulla modalità di collegamento
del cavo di commutazione del freno a mano, consultare la
sezione “Collegamento del cavo del freno a mano ()” sul
lato opposto.
4
*
Dispositivo ausiliare quale un dispositivo di navigazione
hideaway, un sintonizzatore TV e così via.
4
*
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur,avant, droit
Diffusore, anteriore, destro
Luidspreker,voor, rechts
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur,avant, droit
Diffusore, anteriore, destro
Luidspreker,voor, rechts
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continu voeding
power antenna (aerial) control
Motorantennensteuerung
antenne électrique
comando dell’antenna elettrica
automatische antenne
Warning
If you have a power antenna (aerial) without a relay box, connecting this unit with the
supplied power supply lead may damage the antenna (aerial).
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner, or
or when you activate the AF (Alternative Frequency) orTA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the power
antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of
the existing antenna (aerial) booster.For details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• Toavoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a
common negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Notes on connection
• If speaker and amplifier are not connected correctly,“FAILURE” appears in the display. In this case,
make sure the speaker and amplifier are connected correctly.
• If you are to use the monitor for the rear seats, connect the parking brake switch cord to the ground (earth).
1
Opmerking bij de antenne-aansluiting
*
Indien uw auto is uitgerust met een antenne van het type ISO
(International Organization for Standardization), moet u die
aansluiten met behulp van de bijgeleverde adapter . Slui t
eerst de auto-antenne aan op de bijgeleverde adapter en
vervolgens de antennestekker op het hoofdtoestel.
2
*
Tulpstekkersnoer (niet bijgeleverd)
3
Zie “Parkeerremkabel aansluiten ()” op de achterkantvoor
*
meer informatie over het aansluiten op het schakelsnoervan
de parkeerrem.
4
*
Randapparaat, zoals een verborgen navigatieapparaat,
televisietuner, enzovoort
13 57
24 68
Speaker, Front, Left
5
White
Weiß
Blanc
Bianco
Wit
6–
7
Green
Grün
Vert
Verde
Groen
8–
Lautsprecher vorne links
+
Haut-parleur,avant, gauche
Diffusore, anteriore, sinistro
Luidspreker,voor, links
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur,avant, gauche
Diffusore, anteriore, sinistro
Luidspreker,voor, links
Speaker, Rear, Left
Lautsprecher hinten links
+
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
57
48
Red
Rot
7
Rouge
Rosso
Rood
Black
Schwarz
8
Noir
Nero
Zwart
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
ground (earth)
Masse
masse
terra
aarding
11
MEX-DV90/DV90EE/DV900
Foot brake type
Fußbremse
Type pédale de frein
Freno a pedale
Type voetrem
Parking brake switch cord
Parkbremsenschaltleitung
Cordon du capteur du frein
à main
Cavo di commutazione del
freno a mano
Schakelsnoer van de
parkeerrem
Hand brake type
Handbremse
Type frein à main
Freno a mano
Type handrem
Parking brake switch cord
Parkbremsenschaltleitung
Cordon du capteur du frein à main
Cavo di commutazione del freno
a mano
Schakelsnoer van de parkeerrem
1
182 mm
53 mm
Orient the release key correctly.
12
Richten Sie den Löseschlüssel
korrekt aus.
Orientez correctement la clé de
déblocage.
Orientare la chiavetta di rilascio nel
modo corretto.
Plaats de ontgrendelingssleutel op
de juiste manier.
23
Face the hook inwards.
Der Haken muss nach innen
weisen.
Tournez le crochet vers
l’intérieur.
Con il gancetto rivolto verso
l’interno.
Het haakje moet naar binnen
wijzen.
Dashboard
Armaturenbrett
Tableau de bord
Cruscotto
Dashboard
Fire wall
Motorraumtrennwand
Paroi ignifuge
Parete tagliafiamma
Brandschot
Claws
Klammern
Griffes
Morsetti
Klemhaken
AB
Precautions
• Choose the installation location carefully so that the unit will not interfere with
normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high
temperature, such as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake cord
Be sure to connect the parking cord (Light green) of to the parking brake switch
cord. The mounting position of the parking brake switch cord depends on your car.
Consult your car dealer or your nearest Sony dealer for further details.
Removing the protection collar and the
bracket
Before installing the unit, remove the protection collar and the
bracket from the unit.
1 Remove the protection collar .
Engage the release keys together with the protection collar .
Pull out the release keys to remove the protection collar .
2 Remove the bracket .
Insert both release keys together between the unit and the bracket
until they click.
Pull down the bracket , then pull up the unit to separate.
Mounting example
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if necessary (-2).
• Make sure that the 4 catches on the protection collar are properly engaged in the slots of the
unit (-3).
How to detach and attach the front panel
Before installing the unit, detach the front panel.
-ATo detach
Before detaching the front panel, be sure to press . Press , and pull it off
towards you.
-BTo attach
Engage part of the front panel with part of the unit, as illustrated, and push the
left side into position until it clicks.
Warning if your car’s ignition has no ACC
position
Be sure to set theAuto Off function. For details, see the supplied Operating
Instructions.
The unit will shut off completely and automatically in the set time after the unit is
turned off, which prevents battery drain.
If you do not set theAuto Off function, press and hold until the display
disappears each time you turn the ignition off.
RESET button
When the installation and connections are completed, be sure to press the RESET
button with a ball-point pen, etc., after detaching the front panel.
Power connection diagram
Auxiliary power connector may vary depending on the car. Check your car’s auxiliary
power connector diagram to make sure the connections match correctly.There are
three basic types (illustrated below).You may need to switch the positions of the red
and yellow leads in the car stereo’s power supply lead.
After matching the connections and switched power supply leads correctly, connect
the unit to the car’s power supply. If you have any questions and problems connecting
your unit that are not covered in this manual, please consult the car dealer.
Auxiliary power connector
Hilfsstromanschluss
Connecteur d’alimentation auxiliaire
Connettore di alimentazione ausiliaria
Hulpvoedingsaansluiting
Yell ow
Gelb
4
Jaune
Giallo
Geel
Yell ow
Gelb
4
Jaune
Giallo
Geel
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continu voeding
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
the car without ACC position
Fahrzeug ohne Zubehörposition (ACC oder I)
Véhicule sans position ACC
Auto priva della posizione ACC
Auto zonder ACC-positie
Red
Rot
7
Rouge
Rosso
Rood
Red
Rot
7
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continu voeding
Red
Rot
Rouge
Rosso
Rood
Yell ow
Gelb
Jaune
Giallo
Geel
12
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
3-2. SUB PANEL COMPLETE ASSY
(Page 13)
3-3. DVD MECHANISM DECK BLOCK
(Page 14)
MEX-DV90/DV90EE/DV900
SECTION 3
3-4. DC FAN (25X25) (M901),
MAIN BOARD
(Page 14)
Note: Follow the disassembly procedure in the numerical order given.
3-5. SENSOR BOARD,
CHASSIS (T612Z) SUB ASSY
(Page 15)
3-6. CHASSIS (OP, Z) COMPLETE ASSY
(Page 15)
3-2. SUB PANEL COMPLETE ASSY
two bosses
screw
(
PTT2.6×6
3-7. SERVO BOARD
(Page 16)
)
cover
two bosses
sub panel complete assy
two
(
PTT2.6×6
two claws
screws
two claws
)
13
MEX-DV90/DV90EE/DV900
3-3. DVD MECHANISM DECK BLOCK
dust protection sheet
DVD mechanism deck block
R
connector
(
CN3
)
lavel (OP caution)/
laser caution label
shield
(612Z)
two
(
PTT2.6×5
screws
bracket (CD)
screw
(
PTT2.6×6
)
)
two
screws
(
P1.7×2.2
)
3-4. DC FAN (25X25) (M901), MAIN BOARD
three screws
(BTT2.6 × 5)
MAIN board
RB
Lift up the
(
MG-612L-187
fuse (blade type) (auto fuse)
R
(10A/32V) (FU801)
DVD mechanism deck
).
connection cord for automobile
(rear audio out)
connector
(
CN301
)
two
screws
(
PTT2.6×8
(
DC fan
M901
(
25×25
)
)
)
screw
(
PTT2.6×6
screw
(
PTT2.6×8
)
)
14
two
(
PS2.6×14
chassis (CD)
screws
(
)
connector
CN901
)
3-5. SENSOR BOARD, CHASSIS (T612Z) SUB ASSY
claw
two
screws
(
P1.7×2.2
)
Remove the three solders.
SENSOR borad
claw
MEX-DV90/DV90EE/DV900
two
screws
(
P1.7×2.2
)
chassis (T612Z) sub assy
3-6. CHASSIS (OP, Z) COMPLETE ASSY
motor flexible board
(
CN1
)
compression
Turn the gear (RA1) fully in the
direction of arrow ".
spring (damper, Z)
"
chassis (OP, Z) complete assy
OP flexible board
(
CN2
)
two
coil springs (damper)
tension spring (KF)
15
MEX-DV90/DV90EE/DV900
3-7. SERVO BOARD
motor flexible board
(
CN1
)
Remove the two solders.
OP flexible board
(
CN2
)
four
(
M1.7×2.5
screws
)
SERVO board
Remove the three solders.
spacer(PWB7
)
– Bottom view –
16
SECTION 4
ELECTRICAL CHECK
MEX-DV90/DV90EE/DV900
SERVO SECTION
If any of the following parts was replaced, perform the “IOP
Check” as mentioned below.
• Optical pick-up block (chassis (OP, Z) complete assy
or chassis (OP, Z) sub assy)
• Mounted SERVO board
Precaution
Use the following tools and measuring devices.
• Extension jig (Part No.: J-2506-062-1) between the SERVO
board and the MAIN board
• DVD test disc TDV-540C (Part No.: J-2501-235-A)
• CD test disc PATD-012 (Part No.: 4-225-203-01)
• Driver for adjustment
• TV moniter
• Digital voltmeter
• Oscilloscope
• Accessory remote commander
RM-X168
IOP CHECK
Connection:
digital voltmeter
SERVO board
TP51 (IOPDVD), TP47 (IOPCD)
TP63 (A3.3V)
+
–
Check Location:
– SERVO Board (Conductor Side) –
TP47
(IOPCD)
TP51
(IOPDVD)
TP63
(A3.3V)
Procedure:
1. Check the IOP value of DVD and CD by label on the optical
pick-up.
Optical Pick-up Label:
"
CD IOP value
DVD IOP value
2. Connect a digital voltmeter to TP51 (IOPDVD) and TP63
(A3.3V) on the SERVO board.
3. Playback the DVD test disc (TDV-540C), and make a note of
the value of digital voltmeter.
4. Divide the measured voltage value by 1, and convert it into
current value.
5. Check that the calculated value is within ±6 mA to the IOP
value given on the label.
6. Connect a digital voltmeter to TP47 (IOPCD) and TP63
(A3.3V) on the SERVO board.
7. Playback the CD test disc (PATD-012), and make a note of the
value of digital voltmeter.
8. Divide the measured voltage value by 1, and convert it into
current value.
9. Check that the calculated value is within ±6 mA to the IOP
value given on the label.
17
MEX-DV90/DV90EE/DV900
MEMO
18
Loading...