Sony KV-21FA340, KV-21FA540, KV-29FA340, KV-29FA540 Service Manual

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL

MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.

KV-21FA340
KV-21FA340
KV-21FA540
KV-21FA540
KV-29FA340
KV-29FA340
KV-29FA540
KV-29FA540

RM-Y194 LATIN NORTH SCC-S82C-A

RM-Y194 LATIN SOUTH SCC-S82D-A

RM-Y194 LATIN NORTH SCC-S82A-A

RM-Y194 LATIN SOUTH SCC-S82B-A

RM-Y194 LATIN NORTH SCC-S73V-A

RM-Y194 LATIN SOUTH SCC-S73W-A

RM-Y194 LATIN NORTH SCC-S73X-A

RM-Y194 LATIN SOUTH SCC-S73Y-A

BA-6

CHASSIS

ORIGINAL MANUAL ISSUE DATE: 3/2006

REVISION DATE SUBJECT

3/2006 No revisions or updates are applicable at this time.
10/2006 Added revised Wire Dressing information for 21” models. Replaced pages 13-20.
Added Critical note. Replaced page 91.
11/2006 Added revised (Rev. 1.5) Wire Dressing information for 21” models. Replaced pages 13-21.

:UPDATED ITEM

☛

TRINITRON® COLOR TELEVISION

9-883-701-03

Self Diagnosis

Supported model

SERVICE MANUAL

MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.

KV-21FA340
KV-21FA340
KV-21FA540
KV-21FA540
KV-29FA340
KV-29FA340
KV-29FA540
KV-29FA540

RM-Y194 LATIN NORTH SCC-S82C-A

RM-Y194 LATIN SOUTH SCC-S82D-A

RM-Y194 LATIN NORTH SCC-S82A-A

RM-Y194 LATIN SOUTH SCC-S82B-A

RM-Y194 LATIN NORTH SCC-S73V-A

RM-Y194 LATIN SOUTH SCC-S73W-A

RM-Y194 LATIN NORTH SCC-S73X-A

RM-Y194 LATIN SOUTH SCC-S73Y-A

BA-6

CHASSIS

9-883-701-03

KV-21FA540 RM-Y194

TRINITRON® COLOR TELEVISION

KV-21FA340/21FA540/29FA340/29FA540

TABLE OF CONTENTS

SECTION TITLE PAGE SECTION TITLE PAGE

Specifi cations ................................................................................. 4

Warnings and Cautions .................................................................. 6

Safety Check-Out ........................................................................... 7

Self-Diagnostic Function ................................................................. 8

SECTION 1: DISASSEMBLY ............................................................... 10

1-1. Rear Cover Removal ............................................................ 10

1-2. Chassis Assembly Removal ................................................. 10

1-3. Service Position .................................................................... 11

1-4. Picture Tube Removal .......................................................... 12

Anode Cap Removal Procedure .......................................... 12

Cable Wire Dressing ............................................................ 13

KV-21FA340/21FA540 Models Only ................................ 13

KV-29FA340/29FA540 Models Only ................................ 21

SECTION 2: SET-UP ADJUSTMENTS ................................................ 31

2-1. Beam Landing ...................................................................... 31

2-2. Convergence ........................................................................ 32

2-3. Focus ................................................................................... 33

2-4. Screen (G2) .......................................................................... 34

SECTION 3: SAFETY RELATED ADJUSTMENTS ............................. 35

3-1.

X

R530, R531 Confi rmation Method (HV Hold-Down

Confi rmation) and Readjustments ........................................ 35

3-2. B+ Voltage Confi rmation and Adjustment ............................ 35

SECTION 4: CIRCUIT ADJUSTMENTS .............................................. 36

4-1. Remote Adjustment Buttons and Indicators ......................... 36

4-2. Accessing the Service Adjustment Mode ............................. 36

4-3. Confi rming Service Adjustment Changes ............................. 37

4-4. Service Data Lists ................................................................ 38

4-5. ID Map Table ........................................................................ 45

4-6. White Balance Adjustments ................................................. 46

4-7. A Board Adjustments ............................................................ 46

SECTION 5: DIAGRAMS ..................................................................... 49

5-1. Circuit Boards Location ........................................................ 49

5-2. Printed Wiring Board and

Schematic Diagram Information ........................................... 49

5-3. Block Diagrams and Schematics ......................................... 50

Signal Flow Block Diagram .................................................. 50

Audio Block Diagram ............................................................ 51

A Board Schematic Diagram (1 of 2) .................................... 52

A Board Schematic Diagram (2 of 2) .................................... 53

CV Board Schematic Diagram ............................................. 55

HC Board Schematic Diagram ............................................. 56

K1 Board Schematic Diagram (1 of 2)

(KV-21FA540/29FA540 Only) .......................................... 58

K1 Board Schematic Diagram (2 of 2)

(KV-21FA540/29FA540 Only) .......................................... 59

K2 Board Schematic Diagram

(KV-21FA340/29FA340 Only) .......................................... 60

MT Board Schematic Diagram ............................................. 62

5-4. Semiconductors ................................................................... 64

SECTION 6: EXPLODED VIEWS ........................................................ 65

6-1. Chassis ................................................................................ 65

6-2. Picture Tube ......................................................................... 66

SECTION 7: ELECTRICAL PARTS LIST ........................................... 67

KV-21FA340/21FA540/29FA340/29FA540

3

KV-21FA340/21FA540/29FA340/29FA540

/

r

p

)

r

r

p

SPECIFICATIONS

KV-21FA340 KV-21FA540

Power Requirements 120V, 60Hz 120V, 60Hz

(Chile, Perú, Bolivia)

Number of Inputs/Outputs

S Video
Y,P

External for Center/Subwoofe

Audio Panel 11

Front Panel Audio 11

Right & Left Satelite Speakers 1

eaker Output(W

S

Subwoofe

Satelite S

Power Consumption (W)

In Use (Max) 155W 180W

(Chile, Perú, Bolivia)

In Standby (Max)

Dimensions with Subwoofer (W x H x D)

Dimensions of Satelite Speakers (W x H x D)

Mass

Mass of Satelite Speakers

1)

Video

2)

3)

, P

B

R

4)

Audio

5)

RF

Cente
eakers

5)

mm 648 x 569 x 497 mm 648 x 568.5 x 496.4 mm

in

mm 112 x 478.4 x 87 mm

in

kg 28.2 kg 28.2 kg

lbs 62 lbs 1 oz 62 lbs 1 oz

kg .6 kg

lbs 1 lbs 5 oz

220V, 50/60Hz 220V, 50/60Hz

33
11
11
44

11

5W x 2 5W x 2

15W 15W

5W 5W

5W x 2

150W 175W

<1W <1W

25

1/2

x 22

1/2

1/2

x 19

in 25

1)

1 Vp-p 75 ohms unbalanced, sync negative

2)

Y: 1 Vp-p 75 ohms unbalanced, sync negative

C: 0.286 Vp-p (Burst signal), 75 ohms

3) Y: 1.0 Vp-p, 75 ohms, sync negative; PB: 0.7 Vp-p, 75 ohms;

PR Vp-p, 75 ohms.

4)

500 mVrms (100% modulation), Impedance: 47 kilohms

5)

This specifi cation is the maximum wattage.

1/2

x 22

3/8

x 18

4

1/2

3/4

x 19

x 3

1/2

1/2

in

in

KV-21FA340/29FA340 MODELS KV-21FA540/29FA540 MODELS

En calidad de compañía asociada a ENERGY

®

, Corporación Sony ha determinado que

STAR
este producto cumple con las directrices de uso
eficiente de energía de ENERGY STAR
ENERGY STAR
EEUU.

Fabricado bajo licencia de SRS Labs, Inc. WOW y los
símbolos SRS son marcas registradas de SRS Labs,

//

Inc.

Bajo licencia de BBE Sound, Inc. Licenciado de BBE
Sound, Inc. sobre el número USP4638258, 5510752 Y

5736897. BBE y el símbolo son marcas registradas de
BBE Sound, Inc.

Sony, FD Trinitron, WEGA, ClearEdge VM, Intelligent
Picture y Dynamic Bass Response System son marcas
comerciales de Sony.

®

es una marca registrada de

®

.

KV-21FA340/21FA540/29FA340/29FA540

En calidad de compañía asociada a ENERGY

®

, Corporación So ny ha determinado que

STAR
este producto cumple con las directrices de uso
eficiente de energía de ENERGY STAR

ENERGY STAR
EEUU.

Fabricado bajo licencia de SRS Labs, Inc. TruSurround
y los símbolos SRS son marcas registradas de SRS
Labs, Inc.

Fabricado bajo licencia de Dolby Laboratories.
“Dolby”, “Pro Logic” y el símbolo de la doble-D son
marcas comerciales de Dolby Laboratories.

Sony, FD Trinitron, WEGA, ClearEdge VM, Intelligent
Picture y Dynamic Bass Response System son marcas
comerciales de Sony.

®

es una marca registrada de

®

.

Design and specifi cations are subject to change without notice.

4

KV-21FA340/21FA540/29FA340/29FA540

r

p

)

r

r

p

KV-29FA340 KV-29FA540

Power Requirements 120V, 60Hz 120V-220V, 50/60Hz

(Chile, Perú, Bolivia)

Number of Inputs/Outputs

S Video
Y,P

External for Center/Subwoofe

Audio Panel 11

Right & Left Satelite Speakers 1

eaker Output(W

S

Subwoofe

Satelite S

Power Consumption (W)

In Use (Max) 220W 240W

(Chile, Perú, Bolivia)

In Standby (Max)

Dimensions with Subwoofer (W x H x D)

Dimensions of Satelite Speakers (W x H x D)

Mass

Mass of Satelite Speakers

1)

Video

2)

3)

, P

B

R

4)

Audio

5)

RF

Cente
eakers

5)

mm 804 x 697 x 509 mm 804 x 697 x 509 mm

in

mm 112 x 605 x 87 mm

in

kg 49.8 kg 49.8 kg

lbs 109 lbs 10 oz 109 lbs 10 oz

kg .8 kg

lbs 1 lbs 12 oz

220V, 50/60Hz 220V, 50/60Hz

33
11
11
44
11

11

7W x 2 7W x 2

20W 20W

7W 7W

7W x 2

215W 235W

<1W <1W

5/8

31

x 27

1/2

x 20 in 31

1)

1 Vp-p 75 ohms unbalanced, sync negative

2)

Y: 1 Vp-p 75 ohms unbalanced, sync negative

C: 0.286 Vp-p (Burst signal), 75 ohms

3) Y: 1.0 Vp-p, 75 ohms, sync negative; PB: 0.7 Vp-p, 75 ohms;

PR Vp-p, 75 ohms.

4)

500 mVrms (100% modulation), Impedance: 47 kilohms

5)

This specifi cation is the maximum wattage.

5/8

x 27

3/8

4

x 23

3/4

1/2

x 20 in

x 3

1/2

in

Television system

American TV standard, NTSC

Actual screen size

21-inch measured diagonally (KV-21FA340/21FA540 Only)
29-inch measured diagonally (KV-29FA340/29FA540 Only)

Channel coverage

VHF: 2-13/ UHF: 14-69/ CATV: 1-125

Antenna

75-ohm external antenna terminal for VHF/UHF

Picture tube

FD Trinitron® tube

Visible screen size

20-inch picture measured diagonally (KV-21FA340/21FA540 Only)
27-inch picture measured diagonally (KV-29FA340/29FA540 Only)

KV-21FA340/21FA540/29FA340/29FA540

Supplied Accessories

Remote Commander RM-Y194
Two Size AA (R6) Batteries
Telescopic Antenna (KV-21FA340/21FA540 Only)

Optional Accessories

Connection Cables
VMC-810S/820S
VMC-720M
YC-YC-15V/30V
RK74FA

5

KV-21FA340/21FA540/29FA340/29FA540

WARNINGS AND CAUTIONS

CAUTION

Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield, or carbon painted on the CRT, after
removing the anode.

WARNING!!

An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of
this receiver is directly connected to the AC power line.

! SAFETY-RELATED COMPONENT WARNING!!

Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe
operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements
published by Sony. Circuit adjustments that are critical for safe operation are identifi ed in this manual. Follow these procedures
whenever critical components are replaced or improper operation is suspected.

KV-21FA340/21FA540/29FA340/29FA540

6

SAFETY CHECK-OUT

KV-21FA340/21FA540/29FA340/29FA540

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes and
bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or
touching high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.

6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.

7. Check the B+ and HV to see if they are specifi ed values. Make sure
your instruments are accurate; be suspicious of your HV meter if sets
always have low HV.

8. Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.

Leakage Test

The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instructions.

2. A battery-operated AC milliampmeter. The Data Precision 245
digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated digital
multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground. If the
retaining screw is to be used as your earth ground, verify that it is at
ground by measuring the resistance between it and a cold-water pipe
with an ohmmeter. The reading should be zero ohms.

If a cold-water pipe is not accessible, connect a 60- to 100-watt
trouble- light (not a neon lamp) between the hot side of the receptacle
and the retaining screw. Try both slots, if necessary, to locate the hot
side on the line; the lamp should light at normal brilliance if the screw
is at ground potential (see Figure B).

To Exposed Metal

Parts on Set

0.15 F

1.5 K Ω

Earth Ground

Figure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.

KV-21FA340/21FA540/29FA340/29FA540

AC

Voltmeter

(0.75 V)

Trouble Light

AC Outlet Box

Ohmmeter

Cold-water Pipe

7

KV-21FA340/21FA540/29FA340/29FA540

SELF-DIAGNOSTIC FUNCTION

Self Diagnosis

Supported model

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to fl ash. The number
of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY/TIMER LED fl ash indicators is listed in the
instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be used to review
the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

Diagnostic Test Indicators

When an error occurs, the STANDBY/TIMER LED will fl ash a set number of times to indicate the possible cause of the problem. If there is more than
one error, the LED will identify the fi rst of the problem areas.
Results for all of the following diagnostic items are displayed on screen. No error has occurred if the screen displays a “0”.

Diagnostic Item Descrip-

tion

Power does not turn on

+B overcurrent (OCP)*

I-Prot

IK (AKB)

No. of times

STANDBY/ TIMER

lamp fl ashes

Does not light

2 times

4 times

5 times

Self-Diagnositc

Display/

Diagnostic Result

2:0 or 2:1

4:0 or 4:1

5:0 or 5:1

Probable Cause Location

• Power cord is not plugged in.

• Fuse is burned out (F601). (A Board)

• H.OUT (Q502) is shorted. (A Board)

• IC702 is shorted. (CV Board)

• +13V is not supplied. (A Board)

• IC561 is faulty. (A Board)

• IC001 is faulty. (MT Board)

• Screen (G2) is improperly adjusted.**

Detected Symptoms

• Power does not come on.

• No power is supplied to the TV.

• AC Power supply is faulty.

• Power does not come on.

• Load on power line is shorted.

• Has entered standby state after horizontal raster.

• Vertical defl ection pulse is stopped.

• Power line is shorted or power supply is stopped.

• No raster is generated.

• CRT Cathode current detection reference pulse
output is small.

*If a +B overcurrent is detected, stoppage of the vertical defl ection is detected simultaneously. The symptom that is diagnosed fi rst by the
mircrocontroller is displayed on the screen.
**Refer to Screen (G2) Adjustments in Section 2-4. of this manual.

Display of Standby/Timer LED Flash Count

2 times

4 times

5 times

LED ON 0.3 sec.

LED OFF 0.3 sec.

LED OFF

3 sec.

Standby/Timer LED

Diagnostic Item Flash Count*

+B Overcurrent 2 times
I-Prot 4 times
IK (AKB) 5 times
*One fl ash count is not used for self-diagnostic.

Stopping the Standby/Timer LED Flash

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER LAMP from fl ashing.

KV-21FA340/21FA540/29FA340/29FA540

8

KV-21FA340/21FA540/29FA340/29FA540

Self-Diagnostic Screen Display

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confi rmed, it is possible to bring up past
occurrences of failure on the screen for confi rmation.

To Bring Up Screen Test

In standby mode, press buttons on the Remote Commander sequentially, in rapid succession, as shown below:

DISPLAY

Self-Diagnostic Screen Display

Handling of Self-Diagnostic Screen Display

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you
have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.

Clearing the Result Display

To clear the result display to “0”, press buttons on the Remote Commander sequentially when the diagnostic screen is displayed, as shown below:

Channel 8

Quitting the Self-Diagnostic Screen

To quit the entire self-diagnostic screen, turn off the power switch on the Remote Commander or the main unit.

Channel

SELF DIAGNOSTIC

2: +B OCP 0

3: +B OVP N/A

4: VSTOP 0

5: AKB 1

101: WDT N/A

ENTER

5

Sound Volume -

Numeral “0” means that no fault was detected.

Numeral “1” means a fault was detected one time only.

POWER

Note that this differs from entering the Service Mode (Sound Volume

+

).

Self-Diagnostic Circuit

FROM

CV BOARD

IC702 PIN 5

MT BOARD

IC001

Y/CHROMA JUNGLE

51

IK-AKBIN

A BOARD

IC561

V. OUT

REF

3

MT BOARD

IC001

SYSTEM

IO-BDAT

78

I-Prot

53

MT BOARD

IC002

MEMORY

5

BDA

FROM

72

A BOARD

IC501

PIN 1

+B overcurrent (OCP)

Occurs when an overcurrent on the +B (135V) line is detected by pin 72 of IC001 (MT Board). If the voltage of pin 72 of IC001 (MT Board) is less than
1V when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.

I-Prot

Occurs when an absence of the vertical defl ection pulse is detected by pin 78 of IC001 (MT Board). Power supply will shut down when waveform
interval exceeds 2 seconds.

IK (AKB)

If the RGB levels* do not balance within 2 seconds after the power is turned on, this error will be detected by IC001 (MT Board). TV will stay on, but
there will be no picture.

I-HLDWN

O-LED

79

DISPLAY

*(Refers to the RGB levels of the AKB detection Ref pulse that detects IK).

KV-21FA340/21FA540/29FA340/29FA540

9

SECTION 1: DISASSEMBLY

KV-21FA340/21FA540/29FA340/29FA540

1-1. REAR COVER REMOVAL

(KV-29FA540 PICTURED)

1

Lift to remove Subwoofer

from top of Rear Cover.

2

Remove screws from back of cover.
5 Screws
1 Screw +BVTP 4X16 TYPE2 IT-3

3

Remove screws from sides of cover.
3
(

KV-29FA340/29FA540 Only)

2 SCREW +BVTP 4X16 TYPE2 IT-3

(KV-21FA340/21FA540 Only)

Remove screws from top of cover.

4

4
(

KV-29FA340/29FA540 Only)

2 SCREW +BVTP 4X16 TYPE2 IT-3

(KV-21FA340/21FA540 Only)

Remove rear cover

5

SCREW +BVTP 3X12 TYPE2 TT (B)

SCREW +BVTP 4X16 TYPE2 IT-3

SCREW +BVTP 4X16 TYPE2 IT-3

each side

each side

1

4

5

3

2

1-2. CHASSIS ASSEMBLY REMOVAL

(KV-21FA540 PICTURED)

CV Board

KV-21FA340/21FA540/29FA340/29FA540

Claw

Chassis Assembly

10

1-3. SERVICE POSITION

(KV-21FA540 SHOWN)

1

Disconnect the CN501 cable from the A Board.

2

Press on catch tab to release A Board.

3

Gently pull the K1 or K2 Board and the A Board forward to access the HC Board.

Disconnect the speaker cable from the HC Board.

4

Gently continuing pulling the A Board and HC Board forward to place in

5

service position.

Reconnect CN501 and speaker cables

6

KV-21FA340/21FA540/29FA340/29FA540

HC Board

A Board

CV Board

K1 Board (KV-21FA540/29FA540 Only)
K2 Board (KV-21FA340/29FA340 Only)

KV-21FA340/21FA540/29FA340/29FA540

11

1-4. PICTURE TUBE REMOVAL

WARNING: BEFORE REMOVING THE ANODE CAP
High voltage remains in the CRT even after the power is disconnected. To avoid electric shock,
discharge CRT before attempting to remove the anode cap. Short between anode and CRT
coated earth ground strap.

KV-21FA340/21FA540/29FA340/29FA540

1

3

9

4

7

10

1. Discharge the anode of the CRT and remove the

8

6

2

5

anode cap.

2. Unplug all interconnecting leads from the
defl ection yoke, neck assembly, degaussing coils
and CRT grounding strap.

3. Remove the CV Board from the CRT.

4. Remove the chassis assembly.

5. Loosen the neck assembly fi xing screw and
remove.

6. Loosen the defl ection yoke fi xing screw and
remove.

7. Place the set with the CRT face down on a
cushion and remove the degaussing coil holders.

8. Remove the degaussing coils.

9. Remove the CRT grounding strap and spring
tension devices.

10. Unscrew the four CRT fi xing screws [located on
each CRT corner] and remove the CRT [Take
care not to handle the CRT by the neck].

ANODE CAP REMOVAL PROCEDURE

WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to

remove the anode cap. Short between anode and coated earth ground strap of CRT.
NOTE: After removing the anode cap, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield, or carbon
painted on the CRT.

REMOVAL PROCEDURES

c

b

a

Anode Button

Turn up one side of the rubber cap in
the direction indicated by arrow a .

HOW TO HANDLE AN ANODE CAP

1. Do not use sharp objects which may cause damage to the surface of the anode
cap.

2. To avoid damaging the anode cap, do not squeeze the rubber covering too
hard. A material fi tting called a shatter-hook terminal is built into the rubber.

3. Do not force turn the foot of the rubber cover. This may cause the shatter-hook
terminal to protrude and damage the rubber.

Use your thumb to pull the rubber
cap fi rmly in the direction indicated
by arrow b .

When one side of the rubber cap separates from
the anode button, the anode cap can be removed
by turning the rubber cap and pulling it in the
direction of arrow c .

KV-21FA340/21FA540/29FA340/29FA540

12

CABLE WIRE DRESSING

KV-21FA340/21FA540 MODELS ONLY

☛

KV-21FA340/21FA540/29FA340/29FA540

Dress right speaker wire using a purse lock (4­072-499-12) as picture shown.

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

13

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

Jacks

subwoofer
cable

Interlace once VM (A/CN502~CV/CN901) and heater
(A/CN503~CV/CN706) harnesses together as shown in
picture.

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

AC cord

Dress subwoofer harness (K1/CN2403 or
K2/CN3403~A/J207) pass under F-Pin,
behind video jacks & over AC cord as
picture shown.

14

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

100mm

- Dress focus lead and HV cable together using 5mm purse lock
(3-703-981-02), install purse lock 100mm from HV cable's cap. And
pass focus lead through CV board's hook

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

Pass CRT ground wire over DY's cilp & behind DGC as shown
in picture.

15

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

Twist G2 wire without stressing it

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

- Fix G2 wire through FBT G2 clip.

- Pass G2 wire between Focus wire & FBT
as shown in picture.

16

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

Dress right
speaker only with
this purse lock

CAUTION POINT:

Avoid wires to
touch LFT or any
other primary
components

Dress 3P (HC/CN2403~K1/CN2405), 4P
(HC/CN2401~K1/CN2400), 12P harness
(HC/CN2005~MT/CN303) & Right speaker
using a purse lock (3-703-982-02) as shown
in picture.

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

- Dress 3P (HC/CN2403~K1/CN2405), 4P
(HC/CN2401~K1/CN2400), 12P harness
(HC/CN2005~MT/CN303) & Right speaker using two
purse lock (4-072-499-12) to avoid primary circuit.

17

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

For FA540/340C

Dress 3P (K1/CN2402~A/CN412), 5P (A/CN201~K1/CN2600), 10P (A/CN411~K1/CN2401), 3P (HC/CN2403~K1/CN2405), 4P
(HC/CN2401~K1/CN2400), 12P harness (HC/CN2005~MT/CN303) using a 9mm purse lock (3-703-982-02)

For FA340/340C

Dress 3P (K2/CN3404~A/CN412), 10P (A/CN411~K2/CN3405), 3P (HC/CN2403~K2/CN3402), 4P (HC/CN2401~K2/CN3401),
12P harness (HC/CN2005~MT/CN303) using a 9mm purse lock (3-703-982-02)

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

18

KV-21FA340/21FA540/29FA340/29FA540

KV-21FA340/21FA540 MODELS ONLY

☛

CHILE MODELS ONLY

Ferrite
P/N:1-500-586-11

50mm

ALL EXCEPT CHILE MODELS

Dress AC-Cord wire through DGC band lower hook
and using a purse lock (4-072-499-11) as shown in
picuture.

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

Dress AC-Cord wire through DGC band lower hook and
using a purse lock (4-072-499-11) as shown in picuture.

19

KV-21FA340/21FA540 MODELS ONLY

☛

KV-21FA340/21FA540/29FA340/29FA540

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

Make a knot in DGC wire as shown in picuture.

20

KV-21FA340/21FA540 MODELS ONLY

☛

KV-21FA340/21FA540/29FA340/29FA540

REV 1.5

KV-21FA340/21FA540/29FA340/29FA540

knistaeH

revo & CGD rednu rekaeps thgir ssaP

.parw eit s'CGD hguorht eriw rekaeps tfel sserD

.erutcip ni nwohs sa knistaeh

21

KV-29FA340/29FA540 MODELS ONLY

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

rebmuN traP

baL

le

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

TNIOP NOITUAC sa noitisop tcerroc eht ni lioc noitatoR llatsnI :

rebmuN traP

lebaL

KO

GN

.erutcip ni nwohs

cerroc tlit ,detrevni si lioc noitatoR fI :ETON

lliw )unem yb( noit

.noitcerid tnereffid ni krow

22

KV-29FA340/29FA540 MODELS ONLY

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

ton od ,nwohs erutcip sa ecno tsiwt eriw 2G sserD

.eriw sserts revo

.)20-289-307-3( kcol esrup mm9 a gnisu

sa pilc YD hguorht eriw dael lioc noitatoR sserD -

ni nwohs

.erutcip

23

lioc noitator ot )507NC/C~103NC/TM( ssenrah BGR xiF -

KV-29FA340/29FA540 MODELS ONLY

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

mm9 a gnisu eriw dael s'YD sserD

)20-289-307-3( kcol esrup

eb ,niP

3042NC/1K( ssenrah refoowbus sserD

-F rednu ssap )702J/A~3043NC/2K ro
droc CA revo & skcaj oediv dnih

.nwohs erutcip sa

24

KV-29FA340/29FA540 MODELS ONLY

A

BGR

ssenrah

MV

ssenrah

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

:tniop noituaC

ro TFL hcuot ot seriw diov

elbac P21

stnenopmoc yramirp rehto yna

esrup mm9 a gnisu sessenrah retaeH & MV sserD -

.nwohs erutcip sa )20-289-307-3( kcol

-4( kcol esrup hguorht )303NC/TM~5002NC/CH( P21 sserD -

.erutcip ni nwohs sa )21-994-270

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

25

KV-29FA340/29FA540 MODELS ONLY

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

sucoF

elbac

mc 1± 03

skooh retuo

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

,snrut 2 dda selbac niarts )2( gnisu slioc CGD xiF

mc 1± 71

,skooh TRC retuo no selbac kooh

a lioc repu ni 1 esU

.lioc rewol ni 1 dn

no )mottob(sgnirps dna )pot( eriw dnuorg TRC kooH

VH dna dael sucof rehtegot sserD

)20-189-307-3( mm5 )2( gnisu elbac

26

KV-29FA340/29FA540 MODELS ONLY

elbac P21

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

045AF ROF YLNO043AF ROF YLNO

1.1 veR

KV-21FA340/21FA540/29FA340/29FA540

,)5043NC/2K~114NC/A(P01 sserD -

tfeL & )4043NC/2K~214NC/A( P3

mm9 a gnisu sessenrah rekaeps

)20-289-307-3( kcol esrup

.erutcip ni

nwohs sa

P5 ,)1042NC/1K~114NC/A(P01 sserD -

& )2042NC/1K~214NC/A( P3 ,)0062NC/1K~102NC/A(

-3( kcol esrup mm9 a gnisu sessenrah rekaeps tfeL

.erutcip ni nwohs sa )20-289-307

27

KV-29FA340/29FA540 MODELS ONLY

m03 -/+ mm05

m

KV-21FA340/21FA540/29FA340/29FA540

C043/043/C045/045AF92

SLEDOM ELIHC ROF YLNO

etirreF

11-685-005-1:N/P

1.1

R

ve

KV-21FA340/21FA540/29FA340/29FA540

m05

m

-3( kcol esrup mm11 a gnisu CGD ot droC-CA xiF

)21-994-270-4( kcol esrup hguorht & )20-389-307

ecnerefer sa ekaT .erutcip ni nwohs sa

nobrac

.TRC fo enil

28