Sony KV-28FX60A, KV-28FX60B, KV-28FX60D, KV-28FX60E, KV-28FX60K schematic

...

SERVICE MANUAL AE-5 CHASSIS

MICROFILM

MODEL

COMMANDER DEST CHASSIS NO.

KV-28FX60A KV-28FX60B KV-28FX60D KV-28FX60E KV-28FX60K KV-28FX60R KV-28FX60U

RM-891 Italian SCC-Q12D-A

RM-891 French SCC-Q13D-A

RM-891 AEP SCC-Q11D-A

RM-891 Spanish SCC-Q14D-A

RM-891 OIRT SCC-Q16F-A

RM-891 OIRT SCC-Q16E-A

RM-891 UK SCC-Q15C-A

MODEL

COMMANDER DEST CHASSIS NO.

KV-32FX60A KV-32FX60B KV-32FX60D KV-32FX60E KV-32FX60K KV-32FX60R KV-32FX60U

RM-891 Italian SCC-Q12B-A

RM-891 French SCC-Q13B-A

RM-891 AEP SCC-Q11B-A

RM-891 Spanish SCC-Q14B-A

RM-891 OIRT SCC-Q16A-A

RM-891 OIRT SCC-Q16B-A

RM-891 UK SCC-Q15B-A

TRINITRON

COLO R TV

ITEM MODEL Television System Stereo System Channel Coverage Color System

Italian B/G/H,D/K GERMAN Stereo

French

AEP B/G/H, D/K GERMAN Stereo

Spanish B/G/H, D/K GERMAN/NICAM

OIRT

UK I NICAM Stereo UHF : B21-B69

B/G/H, D/K,L,I GERMAN/NICAM

B/G/H, D/K

Stereo

KV-28FX60K/32FX60K GERMAN/NICAM Stereo

KV-28FX60R/32FX60R GERMAN Stereo

ITALIA VHF : A-H2 (C) UHF : 21-69 PAL B/G/H VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05,M1-M10,U1-U10 DK VHF : R01-R12 UHF : R21-R69

L VHF : F02-F10 UHF : F21-F60 CABLE : B-Q B/G/H VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69 I UHF : B21-B69

PAL B/G/H/ VHF : E2-E12 : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69 D/K VHF : R01-R12 UHF : R21-R69

PAL B/G/H/ VHF : E2-E12 : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69

B/G/H/ VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 D/K VHF : R01-R12 UHF : R21-R69

PAL, SECAM NTSC4.43, NTSC3.58 (VIDEO IN)

PAL NTSC4.43, NTSC3.58 (VIDEO IN)

MODEL 28FX60A 28FX60B 28FX60D 28FX60E 28FX60K 28FX60R 28FX60U

Power Consumption 132W 132W 132W 132W 132W 132W 132W

MODEL 32FX60A 32FX60B 32FX60D 32FX60E 32FX60K 32FX60R 32FX60U

PowerConsumption 124W 124W 124W 124W 124W 124W 124W

[PICTURE TUBE] KV -28FX60 FD Trinitro n

Approx. 71 cm (28 inches) (Approx. 66 cm picture measured diagonally) 102 degr ee deflection

[FRONT]

3 Vid eo output - phono jack 3 Audio inputs - ph ono jacks

3 S Video input - 4 pin din

Headphone jack : stereo mini jack

KV -32FX60 FD Trinitro n

Approx. 82 cm (32 inches) (Approx. 76 cm picture measured diagonally) 102 degr ee deflection

Sound output 2x25W (Music Power) Subwoofer 25W (Music Power) Power requirements 220 - 240V

Input/Output Terminals

Dimensions

[REAR]

1/ 1 21-pin Euro connec tor (CENELEC standard ).

- Inputs for Audio and Video signals.

- Inputs for RGB.

- Outputs of TV Video and Audio signals.

2/ 2 21-pin Euro connec tor

- Inputs for Audio and Video signals.

- Inputs for S video.

- Outputs forVideo and Audio signals (selectable).

3/ 3 21-pin Euro connector

- Inputs for Audio and Video signals.

- Inputs for S video.

External speaker terminals : 2-pin Din (5)

KV-28FX60 Approx 772x497x533 (w/h/d) KV-32FX60 Approx 867x564x558 (w/h/d)

Weight KV-28FX60 Approx 42.5kg KV-32FX60 Appr o x 65 kg

Suppli ed accessories RM-891 Remote Com m ander (1)

Other features NICAM*, FASTEXT, TOPTEXT * (KV-28FX60B,28FX60E,28FX60K,28FX60U, 32FX60B,32FX60E, 32FX 60K,32FX60U only)

IEC designated R6 battery (2)

ASA

[RM-891]

Remote control system Infrared control Power requirements 3V dc

2 batteries IEC designation

R6 (size AA) Dimensions Approx 210x56x24mm (w/h/d) Weight Approx 1 10g (Not incl uding battery)

Design and specifications are subject to change with out notice.

Model Name

Item Pal Comb OFF OFF OFF OFF OFF OFF OFF PIP OFF OFF OFF OFF OFF OFF OFF RGB Priority ON ON ON ON ON ON ON Woofer Box ON ON ON ON ON ON ON Scart 1 ON ON ON ON OFF ON ON Scart 2 ON ON ON ON ON ON ON Front in (3) ON ON ON ON ON ON ON Scart 4 ON ON ON ON ON ON ON Projector OFF OFF OFF OFF OFF OFF OFF AKB in 16:9 mode ON ON ON ON ON ON ON Norm B/G ON ON ON ON ON ON OFF Norm I OFF ON OFF OFF OFF OFF ON Norm D/K ON ON ON ON ON ON OFF Norm AUS OFF OFF OFF OFF OFF OFF OFF

KV-28FX60A

KV-32FX60A

KV-28FX60B

KV-32FX60B

KV-28FX60D

KV-32FX60D

KV-28FX60E

KV-32FX60E

KV-28FX60K

KV-32FX60K

KV-28FX60R

KV-32FX60R

KV28FX60U

KV- 32FX60U

Norm L OFF ON OFF OFF OFF OFF OFF Norm SAT OFF OFF OFF OFF OFF OFF OFF Norm M OFF OFF OFF OFF OFF OFF OFF Teletext ON ON ON ON ON ON ON Nicam Stereo OFF ON OFF ON ON OFF ON Language Pres et Italian French German Spanish OIRT OIRT En glish

WARNING (KV-28FX60U/32FX60U only)

The flexible mai ns lead is supplied conne cted to a B.S. 1363 fused plug having a fuse of 5 A MP capacity. Should the fuse need to be replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one that carries th e mark. IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE OUTLET SOCKET. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circ uit should be protected by a 5 AMP FUSE at the distribution board.

How to replace the fuse. Open the fuse compartment with a screwdriver blade and replace the fuse.

FUSE

21 pin connector

R/D/D/D

L/G/S/I

21 19 17 15 13 11

9 7 5 3 1

20 18 16 14 12 10

6 4 2

Pin No 1 2 4 Signal Signal level

1 Audio output B

3 4 Ground (audio) 5 Ground (blue) 6 Audio input A

7 Blue input 0.7 +/- 3dB, 75 ohms positive

8 Function select

9 Ground (green) 10 Open 11 Green Green signal : 0.7 +/- 3dB, 75 ohms,

12 Open 13 Ground (red) 14 Ground (blanking)

_ (S signal Chroma

16 Blanking input

17 Ground (video

18 Ground (video

19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V

_ Video input

21 Common ground

(right) Audio output B

(right) Audio output A

(left)

(AV control)

_ _ Red input 0.7 +/- 3dB, 75 ohms, positive

input)

(Ys signal)

output)

input)

_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V

Y (S signal)

(plug, shield)

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

High state (9.5-12V) : Part mode Low state (0-2V) : TV mode Input impedence : More than 10K ohms Input capacitance : Less than 2nF

positive

0.3 +/- 3dB, 75 ohms, positive

High state (1-3V) Low state (0-0.4V) Input impedence : 75 ohms

(-3+10dB)

(-3+10dB) 1V +/- 3dB, 75ohms, positive sync 0.3V

(-3+10dB)

Pin No.

1 2 3 4

Signal Ground Ground Y (S signal) input C (S signal) input

Connected Not Connected (open) * at 20Hz - 20kHz

Signal Level

1V 3dB 75 ohm, positive Sync. 0.3V -3 + 10dB

0.3V 3dB 75 ohm, positive Sync.

L/G/S/I R/D/D/D

AE-5 SELF DIAGNOSTIC SOFTWARE

The identification of errors within the AE-5 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.

Diagnostic Item

Description

Power does not turn on Does not light Power cord is not plugged in

+B Overcurrent (OCP) 2 times H.OUT (Q6803/6804) is shorted. (D Board)

Vertical Deflection stopped 4 times +15V is not supplied R6835 open (D Board)

No of times Standby

LED Flashes

Fuse is burned out

Linearity FET (Q6806) is shorted. (D Board) IC6604 Power IC is shorted. (D Board)

-15V is not supplied R6834 open (D Board) IC6700 is shorted (D Board)

ERROR

No error 00 Not allowed (may be confused with Sircs response

flash!) Over Current Protection 02 Over Voltage Protection 03 Vertical Protection 04 AKB 05 H - Protection 06 Speaker Protection 07 General IIC Line 0 error 08 MEGATEXT 09 NVM 10 Main colour decoder 11 Feature Box 12 D/A converter 13 Backend 14 Multi sound processor 15 Auto Wide 16 External RAM 17

Probable cause

Location

ERROR COUNT

LED

Detected Symptoms

Power does not come on No power is supplied to the TV AC power supply is faulty

Power does not come on

Load on power line has shorted Vertical deflection pulse has stopped

Power line has shorted

Flash Timing Example : e.g. error number 3

StBy LED

ON ON ON

OFF OFF

ERROR DETECTION MONITOR

Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power on. Each device is checked three times, if there is no acknowledge after every attempt, it will be regarded as an error. There are three steps to check errors

1. IIC line 0 If all devices except the NVM are errors, IIC line 0 error is displayed

2. Board check If all devices mounted on one board have errors, board error is displayed

3. Each device check If IIC line error and board error are not detected then the device with an error is displayed

The detected errors can be displayed as follows:

1. Error Monitor Menu

2. Error Reader

1. ERROR MONITOR MENU

The error monitor menu is displayed by selecting TT33. The following menu will be displayed:

ERROR MONITOR

Operating Time :

930360h 15h

Saved Errors :

1. 100h = A-Board

2. 401h = BP-B CXD2069 MID

3. 704h = J-B TDA9320 Main Col Dec

4. 000h = no error occured

5. 000h = no error occured

Actual Error :

New error code sequence is starting

Ignore Errors : [off]

2. ERROR READER DISPLAY

The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display is S-188-900-10. Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table :

Send Data to Error Reader

Error Code Data high Data Low Error type Function

00 00h - f0h no device

Gen.IIC Error

00 01h f0h 01h IIC 0 line 00 02h f0h 02h IIC 1 line not used

Board Error

01 00h f1h 00h A Board 02 00h f2h 00h B1 Board 03 00h f3h 00h B2 Board 04 00h f4h 00h BP Board 05 00h f5h 00h D1 Board 06 00h f6h 00h E Board 07 00h f7h 00h J Board

Device Error

A Board

01 01h f1h 01h CXA1875 Port Expander 01 02h f1h 02h TU1326 Main Tuner 01 03h f1h 03h TU1350 Sub Tuner

B1 Board

02 01h f2h 01h P83C654 Feature Box 02 02h f2h 02h SDA9280 D/A Converter

B2 Board

03 01h f3h 01h SAA4977 Basic 03 02h f3h 02h SAA4950 Memory

BP Board

04 01h f4h 01h CXD2069 MID

D1 Board

05 01h f5h 01h CXA8070 Dynamic Conv. 05 02h f5h 02h CXA1875 Port Expander

E Board

06 01h f6h 01h CXD2100 Backend

J Board

07 01h f7h 01h CXD2057 Auto Wide 07 02h f7h 02h SDA9288 PIP 07 03h f7h 03h TDA9320 Sub Colour 07 04h f7h 04h TDA9320 Main Colour 07 05h f7h 05h CXA1875 Sub Sound 07 06h f7h 06h TDA7309 HP Amp 07 07h f7h 07h TEA6422DT Audio SW 07 08h f7h 08h MSP3410D Sound Proc 07 09h f7h 09h TC9337F Sound DSP

TABLE OF CONTENTS

Section Title Page Section Title Page

Warning and Caution .....................3

Self-Diagnostic Function . ....................5

1. GENERAL

Overview .....................9

First time operation .....................10

Advanced Operations .....................11

Teletext .....................16

2. DISASSEMBLY

2-1. Rear Cover Removal .....................17

2-2. Chassis Assy Removal .....................17

2-3. Service Position .....................17

2-4. U Board Removal .....................17

2-5. J Board Removal .....................18

2-6. J Shield Removal .....................18

2-7. B1 Board Removal .....................18

2-8. Picture Tube Removal .....................19

Removal and Replacement of the

Main-Bracket bottom plates .....................20

3. SET-UP ADJUSTMENTS

3-1. Beam Landing ................... ..21

3-2. Convergence .....................22

3-3. Focus .....................24

3-4. Screen [G2] White Balance .....................24

4. CIRCUIT ADJUSTMENTS

4-1. Electrical Adjustments .....................26

4-2. Volume Electrical Adjustments .....................32

4-3. Test Mode 2 .....................33

5. DIAGRAMS

5-1. Block Diagram (1) .....................35

Block Diagram (2) .....................40

Block Diagram (3) .....................45

Block Diagram (4) .....................50

5-2. Circuit Board Location .....................53

5-3. Schematic Diagrams and

Printed Wiring Boards .....................53

* C Board .....................55

* J Board .....................63

* U Board .....................73

* A Board .....................79

* B1 Board .....................83

* VM Board .....................88

* D1 Board .....................93

* M Board .....................97

* E Board .....................101

* D Board .....................109

* F1 Board .....................113

* H1 Board .....................114

* F Board .....................115

5-4. Semiconductors .....................117

5-5. IC Blocks .....................120

6. EXPLODED VIEWS

6-1. Chassis .....................121

6-2. Picture Tube .....................123

7. ELECTRICAL PARTS LIST

.....................125

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE ANODE CAP

WARNING !!

AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE POWER LINE.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY SHADING AND MARKED ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION

APRES AVOIR DECONNECTE LE CAP DE’LANODE, COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE.

ATTENTION !!

AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT D’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE. LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.

ATTENTION AUX COMPOSANTS RELATIFS Á LA

SÈCURITÈ !!

LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES

EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.

SECTION 1

GENERAL

The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain

as in the manual.

Overview

This section briefly describes the buttons and controls on the TV set and the Remote Control. Open the flaps at the front and back of his Instruction Manual for detailed illustrations. For more information refer to the page numbers given in the overview.

TV-set – front and top

Symbol Description See page

B q 3 S-video input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

C … 3, ≤ 3 Phono video/audio inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Remote Control

Symbol Description See page

u TV: standby mode on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1 TV

R Teletext: Freezing a subpage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Å/a

5 > PIP: Selecting the source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

´/´

7 1, 2, … 9, 0 Number buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TV: on-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Teletext: index page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Selecting of input source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

PIP: Swapping the screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

PIP: Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Back to the channel last selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

D u Indicator for Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

E U Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

F … Selecting of input source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

G ¸ +/– Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

H PROGR +/– Channel selection up- and downwards . . . . . . . . . . . . . . . . . . . . . . 32

I CONTROL Control panel: Switching on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

F G H I

PROGR

+–+

–

CONTROL

L/G/S/I

R/D/D/D

9 Selecting of screen format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

!¡ Joystick for menu selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

!™ MENU Switching on and off of Menu system . . . . . . . . . . . . . . . . . . . . . . . . . . 31

!£ PROGR +/– TV: Channel selection up- and downwards . . . . . . . . . . . . . . . . . . . . . 32

No function on this set

Press OK to confirm

Teletext: Page selection up-and downwards . . . . . . . . . . . . . . . . . . . . . 42

MLKJ

L/G/S/I

R/D/D/D

!¢ ¸ +/– Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

!∞

!§

!¶

-/--

!•

Picture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Equaliser mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selection of double digit channel numbers . . . . . . . . . . . . . . . . . . . . . . 32

Freezing of TV picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

!ª No function on this set

@º

@¡

;

@™ @£ VIDEO

u VCR: Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Teletext: Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

TV: Selecting of TV mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Teletext: Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Muting of sound on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Buttons under cover

@¢

@∞ CH +/– VCR operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

VTR 1 2 3 4 MDP Video equipment selector 0 z ) p P r Buttons for VCR operation

@§

Displaying of the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Resetting of picture setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TV-set – rear

Symbol Description See page

KY2/j2 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

N| L/G/S/I Audio phono jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

L/G/S/I R/D/D/D

333

A B C

1/ 1 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3/j3 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

DVD VHS

Aerial socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

R/D/D/D

First Time Operation

The following chapter contains all the steps necessary when first installing your TV and the basic TV functions.

Step 1 Installation

A Connecting the TV Set

1 Connect the TV set to the mains socket (220-240 V. AC, 50 Hz). 2a Connect a conventional aerial cable to the socket marked ˘ M on the rear of the TV set.

2b Connect your Satellite Receiver to one of the Scart connectors J K L of the TV set.

When connecting a VCR to your TV set:

We recommend that you use the preset function Manual Programme Preset (page 33) to tune in the VCR signal to programme position 0.

Step 2 Basic Presetting

A The Menu System

Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system:

Press MENU !™ to switch the menu on and off.

•

Use “, ”, 4, $ of the joystick !¡ to select within the menu system.

•

Press OK to store.

•

When menu is switched off:

•

Press “ to return to the last menu screen.

Language/Country

Language

Country

Select: Enter:

English

Off

VIDEO

L/G/S/I

R/D/D/D

OUT IN

SAT

B Inserting the Batteries into the Remote Control

Make sure to insert the batteries using the correct polarities. Dispose of exhausted batteries according to your local regulations.

C Switching on the TV Set

Press the switch U E at the front of the TV set.

•

If the standby mode indicator u D on the TV is lit, press TV I/ Remote Control to switch on the TV set.

u 1

on the

B Selecting Language and Country

1 Press the MENU !™ button.

The menu Language/Country appears on the screen.

2 Push the joystick !¡ to ”. Push the joystick !¡ to $ to select the language.

Press OK !¡. The menus appear in the selected language.

3 Push the joystick !¡ to $ to select Country. Push the joystick !¡ to ”. 4 Select the country in which you will operate the TV set using $ or 4 .

Confirm by pressing OK !¡. The menu Auto Tuning appears.

C Automatic Tuning In of Channels

Push the joystick !¡ to ”.

•

After all available channels are stored, the TV goes back to the programme position with which you started the automatic tuning. Your TV is now ready for use.

To stop the automatic tuning: Press OK !¡.

If you wish to change the sequence of the stored channels, go to Sorting Programme Positions in Advanced Presetting.

If you need to change or repeat the tuning afterwards (e.g. when you move house) : select the menu Auto Tuning in the Set Up

menu.

1 2 3 4 5

Searching

CO2 CO3 CO4 CO7 CO8

Language/Country

Language

Country

Select: Enter:

Language/Country

Language

Country

Select Country:

Set Up

Auto Tuning

Programme Sorting AV Preset Installation

Start Auto Tuning:

Select:

English

Off

English

Belgium

Bulgaria

Czech Rep.

Denmark

Confirm: OK

Start

Austria

Finland

Off

First Time Operation

Advanced Operation

PROG SEARCHSYS

Off

SKIP LABEL

0 EXT

AV1

RGB

AV2

YC2

AV3

YC3

AV1

PROG SYS

Off

SKIP LABEL

1 B/G

Advanced Operation

Advanced Presetting

Sorting of Programme Positions

After having used Automatic Tuning of channels you may wish to rearrange the order of the channels.

1 Press MENU. Select the symbol 2 Select Programme Sorting using $. Push to ” to enter. 3 Select the programme position of the channel you wish to sort using 4 or $.

Push to ” to enter.

4 Move the channel to the new programme position using 4 or $. Store by

pressing OK. The channel is now at the new position. The other programme positions move accordingly.

5 To sort other programme positions repeat steps 3 to 4. 6 Press MENU to return to the normal TV screen.

Manual Tuning In of Channels

Use this function to preset channels or a video input source one by one to programme positions of your choice.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position by pushing to 4 or $. Push twice to ”.

The column SYS is highlighted.

4 Select the TV system using 4 or $. Push to ” to enter.

Available TV systems are B/G for western European countries, D/K for eastern European countries, EXT for a video input source (please go to step 5c after selecting EXT) The column SEARCH is highlighted.

5 Select your method for the channel tuning using 4 or $. Push to ” to enter.

You have the choice between C for a terrestrial channel, S for a cable channel, F for direct frequency input.

a Direct Channel Input - S, C or F

For channel numbers input a two digit number, for the channel frequency a three digit number.

Select the two or three digits by using the number buttons 0 to 9.

•

To start the search and to store the channel, press OK.

•

To preset other channels repeat steps 3 to 5a.

•

b Channel search (SEARCH)

Use Search if you do not know the channel number or frequency Start the search for the next available channel by pushing to $.

•

Store the channel by pressing OK or continue the search by pushing again to $.

•

To search for other channels repeat steps 3 to 5b.

•

c For video input sources (EXT)

Select the Video Input source using 4 or $.

•

Store your selection by pressing OK.

•

To allocate other sources repeat steps 3 to 5c.

•

6 Press MENU to return to the normal TV screen.

using $. Push to ”.

Set Up

Auto Tuning

Programme Sorting

Select Next View Dolby Surround Set Up AV Preset Installation

Select: Enter:

Programme Sorting

PROG CH LABEL

TV 5

C03

PRO 7

C05

EU-SP

C07

SWF

C08

RTL

C09

SAT

C11

MDR

C12

DDI

C13

DSF

C14

RTL 2

C15

KAB 1

C16

Select: Enter:

Programme Sorting

PROG CH LABEL

TV 5

C03

PRO 7

C05

EU-SP

C07

SWF

C08

RTL

C09

SAT

C11

MDR

C12

DDI

C13

DSF

C14

RTL 2

C15

KAB 1

C16

Select Prog: Confirm: OK

Installation

Language/Country

Manual Programme Preset

Further Programme Preset RGB Set Up Picture Rotation Personal ID Demo

Select: Enter:

Manual Programme Preset

PROG SEARCHSYSSKIP LABEL

C09

B/G

Off

C10

B/G

Off

Select: Enter:

PROG

SKIP

SEARCHSYS LABEL

B/G

Off

D/K EXT

PROG SYS

SKIP LABEL

Off

1 B/G

PROG SYS

SKIP LABEL

Off

1 B/G

PROG SEARCHSYS

SKIP LABEL Off

0 EXT

AV1

RGB AV2 YC2 AV3 YC3

First Time Operation

C03 TV 5

- - - - - - -

ARD BBC

Advanced Presetting

Sorting of Programme Positions

After having used Automatic Tuning of channels you may wish to rearrange the order of the channels.

1 Press MENU. Select the symbol

using $. Push to ”.

2 Select Programme Sorting using $. Push to ” to enter. 3 Select the programme position of the channel you wish to sort using 4 or $.

Push to ” to enter.

4 Move the channel to the new programme position using 4 or $. Store by

pressing OK. The channel is now at the new position. The other programme positions move accordingly.

5 To sort other programme positions repeat steps 3 to 4. 6 Press MENU to return to the normal TV screen.

Manual Tuning In of Channels

Use this function to preset channels or a video input source one by one to programme positions of your choice.

AV1

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position by pushing to 4 or $. Push twice to ”.

The column SYS is highlighted.

4 Select the TV system using 4 or $. Push to ” to enter.

5 Select your method for the channel tuning using 4 or $. Push to ” to enter.

You have the choice between C for a terrestrial channel, S for a cable channel, F for direct frequency input.

a Direct Channel Input - S, C or F

For channel numbers input a two digit number, for the channel frequency a three digit number.

Select the two or three digits by using the number buttons 0 to 9.

•

To start the search and to store the channel, press OK.

•

To preset other channels repeat steps 3 to 5a.

•

b Channel search (SEARCH)

Use Search if you do not know the channel number or frequency Start the search for the next available channel by pushing to $.

•

Store the channel by pressing OK or continue the search by pushing again to $.

•

To search for other channels repeat steps 3 to 5b.

•

c For video input sources (EXT)

Select the Video Input source using 4 or $.

•

Store your selection by pressing OK.

•

To allocate other sources repeat steps 3 to 5c.

•

6 Press MENU to return to the normal TV screen.

using $. Push to ”.

Set Up

Auto Tuning

Programme Sorting

Select Next View Dolby Surround Set Up AV Preset Installation

Select: Enter:

Programme Sorting

PROG CH LABEL

TV 5

C03

PRO 7

C05

EU-SP

C07

SWF

C08

RTL

C09

SAT

C11

MDR

C12

DDI

C13

DSF

C14

RTL 2

C15

KAB 1

C16

Select: Enter:

Programme Sorting

PROG CH LABEL

TV 5

C03

PRO 7

C05

EU-SP

C07

SWF

C08

RTL

C09

SAT

C11

MDR

C12

DDI

C13

DSF

C14

RTL 2

C15

KAB 1

C16

Select Prog: Confirm: OK

Installation

Language/Country

Manual Programme Preset

Further Programme Preset RGB Set Up Picture Rotation Personal ID Demo

Select: Enter:

Manual Programme Preset

PROG SEARCHSYSSKIP LABEL

C09

B/G

Off

C10

B/G

Off

Select: Enter:

PROG

SKIP

SEARCHSYS LABEL

B/G

Off

D/K EXT

PROG SYS

SKIP LABEL

Off

1 B/G

S F

First Time Operation

C03 TV 5

- - - - - - -

ARD BBC

Advanced Presetting

Captioning a Station Name

During presetting the channels are usually labelled automatically. You can, however, individually name a channel or a video input source.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position of the channel or the video source you wish to

label by pushing to $ or 4. Push repeatedly to ” until the first element of the position LABEL is highlighted.

4 Select a number, a letter, + or a blank using 4 or $. Push to ” to confirm.

Select the other four characters in the same way.

using $. Push to ”.

5 Store your selection by pressing OK. 6 To label other channels or video sources repeat steps 3 to 5. 7 Press MENU to return to the normal TV screen.

Skipping of Programme Positions

In case of 100 programme positions there may be unused positions, which you can skip in the menu Manual Programme Preset. When changing channels with the PROGR +/– buttons they do then not appear. You can, however, still select them using the number buttons.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position you wish to skip by pushing to 4 or $.

Push to ” to enter. The column SKIP is highlighted.

4 Select ON using $. 5 Store by pressing OK. 6 To skip other programme positions repeat steps 3 to 5. 7 Press MENU to return to the normal TV screen.

using $. Push to ”.

Manual Programme Preset

PROG SEARCHSYSSKIP LABEL

C09

ARD

B/G

Off

C10

BBC

B/G

Off

Select: Enter:

PROG SEARCHSYS

SKIP LABEL

Off

6 B/G

C07 TE

Manual Programme Preset

PROG SEARCHSYSSKIP LABEL

C09

ARD

B/G

Off

C10

BBC

B/G

Off

Select: Enter:

PROG SEARCHSYSSKIP LABEL

F189 - - - Off

53 B/G

Advanced Presetting

Using of Further Programme Preset

Using the menu Further Programme Preset you can a) individually adjust the volume level of each channel. b) improve the quality of a weak channel (picture or sound distortions) with

manual fine tuning.

c) preset the AV output for programme positions of those channels with

scrambled signals (e.g. from a Pay TV decoder). In this way a connected VCR records the unscrambled signal.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Further Programme Preset

using $. Push to ” to enter.

3 Select the programme position of the desired channel by pushing to 4 or $.

Push repeatedly to ” to select: VOL (Volume Offset), AFT (Automatic Fine Tuning) or DECODER. The selected item changes colour.

4a VOL

Push to 4 or $ to adjust the volume level (range -7 to +7) of the channel. Store by pressing OK. Repeat steps 3 and 4a if you wish to adjust the volume level of other channels.

b AFT

Push to $ to select OFF. Push to ” to enter Manual Fine Tuning. Push to 4 or $ to fine tune the channel (range -15 to +15). Store by pressing OK. Repeat steps 3 and 4b if you wish to fine tune other channels.

c DECODER

Push to 4 or $ to select AV1 (Euro AV socket 1) or AV2 (Euro AV socket 2) as output for the video source on this programme position. Store by pressing OK. Repeat steps 3 and 4c if you wish to preset the AV output of other video sources.

Should you use Auto Tuning afterwards, this setting will be cancelled.

5 Press MENU to return to the normal TV screen.

using $. Push to ”.

Installation

Language/Country Manual Programme Preset

Further Programme Preset

RGB Set Up Picture Rotation Personal ID Demo

Select: Enter:

Further Programme Preset

PROG AFTVOL DECODER

Select: Enter:

PROG AFT DECODER

PROG DECODER

- - - - - - -

Off

On 4 5 6 7 8 9 10 11

VOL

AFT

-5

Off

VOL

AFT

-5

Off

AV1 AV2

Advanced Operation

Advanced Presetting

Adjusting the Picture Geometry for an RGB Source

When connecting an RGB source such as a Sony playstation you may need to readjust the picture geometry.

1 Select the connected RGB source by pressing … repeatedly. 2 Press MENU. Select the symbol 3 Select Installation using $. Push to ” to enter. Select RGB Set Up using $.

Push to ” to enter.

4 Select H Centre by pushing to ”. Adjust the centre of the picture

(range from -5 to +5) using 4 or $. Store by pressing OK.

5 Select H Size using $. Push to ” to enter. Adjust the horizontal coordinates

(range from -5 to +5) using 4 or $. Store by pressing OK.

using $. Push to ”.

6 Press MENU to return to the normal TV screen.

Adjusting the Picture Rotation

Because of the earth magnetism the picture might slant. In this case you can readjust the picture.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Picture Rotation using $.

Push to ” to enter.

3 Adjust the Picture Rotation (adjusting range -4 to +4) by pushing to 4 or $.

Store by pressing OK.

4 Press MENU to return to the normal TV picture.

using $. Push to ”.

RGB Set Up H Centre

H Size

Adjust Position: Confirm: OK

RGB Set Up

H Centre

H Size

Adjust Position: Confirm: OK

Installation

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up

Picture Rotation

Personal ID Demo

Select: Confirm: OK

Inputting Your Personal ID

You can programme your TV with a safety code, so that you can be traced if your TV is stolen and recovered. This code can only be input once!

Make sure to write it down in this Instruction Manual.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Personal ID using $.

Push to ” to enter.

3a Select the first of a total of 11 characters (letter, number, + or a blank) by

using 4 or $.

b Push to ” to go to the next character. c Repeat a and b for all characters.

using $. Push to ”.

4 Store by pressing OK. 5 Press MENU to return to the normal TV screen.

Installation

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up Picture Rotation

Personal ID

Demo

Select: Confirm: OK

- - - - - -

Presetting and Labelling of Input Sources

Using AV Preset you can select the automatic format function and label an input source.

1 Press MENU. Select the symbol 2 Select AV Preset using $. Push to ” to enter. 3 Select the desired AV input (AV 1, 2 or 3) using 4 or $. Push to ” enter.

After each step you have the choice between memorizing (press OK) or going to the next item (push to ”).

4 For automatic format selection of the AV input:

a Push to ” to select Auto Format. b Select On or Off using 4 or $.

5 To label the source:

a Push to ” to select Label. b Select the first character using 4 or $. Push to ” to confirm. c Repeat step b to select the other 4 characters.

d Store by pressing OK. 6 Repeat steps 3 to 5 for the other AV inputs. 7 Selecting the AV3 Input Source:

In case of AV3 you have the choice between the front AV3 sockets BCor the rear Scart 3 L connector.

a Push to $ to select AV3 Input. Push to ” to enter.

b Select Front or Rear using 4 or $.

c Store by pressing OK. 8 Press MENU to return to the normal TV screen.

using $. Push to ”.

AV Preset

INPUT LABEL

AUTO FORMAT

On On On

AUTO FORMAT

On On On

VIDEO VIDEO VIDEO

VIDEO VIDEO

VIDEO

Front

Rear

AV 1

AV 2 AV 3

AV 3 Input Rear

Select Mode: Enter:

AV Preset

INPUT LABEL

AV 1 AV 2 AV 3

AV 3 Input

Select Mode: Confirm: OK

Advanced Operation

Advanced TV operation

Adjusting Picture and Sound

Picture and sound are adjusted at the factory. You can, however, adjust them individually.

1 Press MENU.

Select the symbol Push to ” to enter. The menu Picture or Sound Control is displayed.

2 Select the desired item using 4 or $. Push to ” to enter. 3 Adjust the selected item using 4, $, ” and “. Press OK to store.

Refer to the tables on this and the following page for more information.

4 Repeat steps 2 and 3 to adjust other items. 5 Press MENU to return to the normal TV screen.

Picture Control Item Effect/Operation

Picture Mode $ Personal (for individual settings)

Contrast Less “” More Brightness* Darker “” Brighter Colour* Less “” More Hue** Greenish “” Reddish Sharpness* Softer “” Sharper Reset Resets picture to the factory preset levels AI $ Off: normal

(Artificial Intelligence) 4 On: Automatic optimization of contrast level

Noise Reduction $ Off: Normal

* Only if Personal is selected in Picture Mode ** Only available for NTSC colour signal (e.g. US video tapes)

for Picture or for Sound using 4 or $.

Movie (for movie broadcasts)

4 Live (for live broadcasts)

according to the TV signal

4 On: Reduces picture noise in case of a weak

broadcasting signal

Picture Adjustment

Picture Mode

Contrast Brightness Colour Sharpness Reset AI Noise Reduction

Select Mode: Enter:

Picture Mode

Contrast

Noise Reduction

Personal

Movie

Advanced TV operation

Sound Control Item Effect/Operation

Equaliser Mode Select between the following sound settings

On On

Equaliser adjustment You can adjust the mode selected in Equaliser

Balance 4 More left

Loudness 4 Off: Normal

Live

Space 4 Off: Normal

Auto Volume Control $ On: volume level of the channels will stay the same

Dual Sound

Off

Headphones

2 Volume Less “ ”More 2 Dual Sound

4 Personal

Vocal Jazz Rock Pop

$ Flat (fixed setting, cannot be adjusted)

mode by cutting and boosting of 5 selected frequency bands. Only the changes made in Personal can be stored, the others return to factory setting. Select the desired bar using ” or “, adjust using 4 and $. Press OK to store.

$ More right

$ On: For music broadcasts

$ On: Special accoustic effect

independent of the broadcast signal (e.g. in case of advertisements)

4 Off: volume level changes according to the

broadcast signal For a bilingual broadcast:

•

A for channel 1“ ”B for channel 2 For a stereo broadcast:

•

Stereo“ ”Mono For a Nicam broadcast: When receiving a Nicam broadcast »NICAM« appears briefly on the screen.

For a bilingual broadcast:

•

A for channel 1“”B for channel 2 For a stereo broadcast:

•

Stereo“”Mono PIP

•

When PIP is switched on, you can additionally select the PIP sound for the headphones

Audio Adjustment

Equaliser Mode

Equaliser Adjustment Balance Loudness Space Auto Vol. Control Dual Sound Volume Dual Sound

Select Mode: Confirm: OK

Equaliser Adjustment

Personal

+ 0 –

120 150 1,5K 5 K 10 K

Sel: Adjust: Confirm:OK

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Vocal

Jazz

Rock

Pop Flat

On Off Off

Mono

Off

Stereo

Mono

Stereo

Mono

Advanced Operation

Advanced TV operation

Using the Features Menu

1 Press MENU. Select the symbol using $. Push to z. 2 Select the desired menu item using $. Push to z to enter. 3 Select the desired setting using 4 or $. 4 Store by pressing OK. 5 Press MENU to return to the normal TV screen.

Features Item Effect/Operation

Auto Format $ On: Automatic selection of the screen format

PIP Position See next page for details Sleep Timer

Parental Lock $ Off: Normal mode

AV2 Source You can select the source to be output from the

4 Off: Normal mode

You can select a time period after which the TV switches itself into standby mode

$ Off

10 min. 20 min.

4 90 min.

4 On: TV can only be switched on out of

standby-mode using the Remote Commander, the buttons on the TV do not work.

Scart connector record from this socket while watching another source.

$ TV audio/video signal from the aerial ˘

AV1 audio/video signal from Scart 1 AV2 audio/video signal from Scart 2

4 AV3 audio/video signal from front or rear connectors

2/j2. In this way you can

Features

Auto Format

PIP Position Sleep Timer

Parental Lock AV 2 Source

Select: Enter:

Auto Format

Sleep Timer

Parental Look

AV 2 Source

10 min

AV 3 AV 2 AV 1

Using Picture-in-Picture

Off Off TV

Off

Picture-in-Picture (PIP) lets you display a second, small screen within the main TV picture. In this way you can watch the video output from any connected equipment, e.g., from a VCR, while watching TV.

Switching PIP on and off

Press

•

´/´

6 . The small screen is displayed. The source of the small screen is the one last used when the TV was on. Press

•

Selecting a PIP source

1 Press > 5.

The symbol > is displayed in the bottom left-hand corner of the screen.

6 again to switch PIP off.

´/´

2 Press … 3 repeatedly until the desired source appears.

You can select between TV , AV1, AV2, YC2, AV3 and YC3.

If no video source (e.g. VCR or Camera) is connected, the PIP will be noisy.

You cannot display an RGB source in the PIP.

Swapping the screens

Å/a

Press

•

The two screens are swapped.

Changing channels if the TV picture is in the PIP

First press >, then the respective number buttons.

•

Changing the PIP position

There are four different positions of the small screen within the main screen. Select the PIP position in the Features menu.

1 Press MENU. Select the symbol using $. Push to ” to enter. 2 Select PIP position by pushing to $. Push to ” to enter. 3 Select the desired position using $ or 4. Press OK to select. 4 Press MENU to return to the normal TV screen.

Main screen

Features

Auto Format

PIP Position

Sleep Timer Parental Lock AV 2 Source

Select: Enter:

Å/a

PIP

Off Off TV

Advanced Operation

Teletext

Most TV channels broadcast information via teletext. The index page of the teletext service (usually page 100) gives you information on how to use their service.

Make sure to use a TV channel with a strong signal, otherwise there may be

Teletext errors.

Direct Access Functions

Switching Teletext on and off

1 Select the TV channel which carries the teletext service you want to view. 2a Press f @º once to switch teletext on.

The teletext menu is displayed.

b Press f twice for Mix mode.

The TV broadcast and the Teletext display are overlapped.

3 Press

;

@¡ or press f a third time to switch teletext off.

Selecting a Teletext Page

Direct Page Selection

Input the three digits of the page number using the number buttons 7.

•

If you have made a mistake: Type in any three digits, then reenter the correct page number.

Page Catching 1 Select a teletext page which has several page numbers on it (e.g., the index

page).

2 Press OK !¡.

Page Catching is displayed at the top of the page

3 Select the desired page number using 4 or $ !¡ and press OK.

The requested page is displayed after some seconds.

Selecting the next or the preceding page

Press !£ (Page +) or (Page -).

•

Selecting the index page

Press + 2.

•

Selecting a subpage

A teletext page may consist out of several subpages. In this case an information line is displayed, showing the number of the subpages. Select the mode by pushing to 4. Select the subpage by using 4 or $.

•

Freezing a Teletext subpage

1 Press 3 or R

The symbol R 3 is displayed and the subpage is not updated.

2 Press f @º to resume normal teletext reception.

Using Fastext*

*depending on availability of service

Fastext lets you access pages with one button stroke. When Fastext is broadcast, a colour-coded menu appears at the bottom of the screen. The colours of this menu correspond to the red, green, yellow and blue buttons on the Remote Control 9, !º, !¢, !∞. Press the coloured button which corresponds to the colour in the

•

colour-coded menu.

216-02

01 03 04 05 06 07 0802

Teletext

Using the Teletext Menu

This TV set has a menu-guided teletext system. When teletext is switched on you can use the joystick buttons to operate the teletext menu.

Select the menu functions as follows:

1 Press MENU !™.

The Teletext menu is superimposed on the teletext display.

2 Select the teletext function using 4 or $ !¡. Push to ” to enter.

Top/Bottom/Full

For convenient reading of a Teletext page you can enlarge it. After having selected the function, a sub menu Top 4 Bottom $ Full OK is displayed.

Push to 4 to enlarge the upper half of the screen, push to $ to enlarge the lower

•

half. Press OK to resume the normal size.

Text Clear

After having selected the function, you can watch a TV channel while waiting for a requested Teletext page. As soon as the page is available, the symbol f changes colour.

Press f to view the page.

•

Reveal

Some teletext pages contain hidden information (e.g., for a quiz), which you can reveal. After having selected the function, the hidden information appears.

Press f to resume the normal Teletext operation.

•

Time Page*

*depending on availability of service

You can call up a time-coded page - such as an alarm page - at a time specified by you.

After having selected the function a sub menu is displayed.

1 Select On using 4 or $. Push to ” to enter. 2 Enter the three digits of the desired page using the number buttons 7.

Push to ” after each digit.

3 Enter the four digits of the desired time using the number buttons 7.

Push to ” after each digit.

4 Press OK to store.

The time is displayed in the top left-handed corner of the screen. At the requested time the page is displayed.

Teletext

Top / Bottom / Full

Text Clear Reveal Time Page

Select: Enter:

Top: Bottom: Full: OK

Time Page

PAGE TIME – – – - - : - -

Select: Enter:

Advanced Operation

SECTION 2

DISASSEMBLY

2-1. REAR COVER REMOVAL

2-2. CHASSIS ASSY REMOVAL

2 Rear Cover

1 6 Screws BTV 4x16

2-3. SERVICE POSITION

2-4. U BOARD REMOVAL

1 Push the claw in the direction of the arrow and remove.

2 Pull the Board in the direction of the arrow and remove.

2-5. J BOARD REMOVAL

2-6. J SHIELD REMOVAL

1 Push the claw in the direction of the arrow and remove.

3 Remove the shield in the direction of the arrow.

2 Push the claw in the direction of the arrow and remove.

2 Pull the Board in the direction of the arrow and remove.

NOTE

All other boards are removed in a similar manner to those shown

2-7. B1 BOARD REMOVAL

2-8. PICTURE TUBE REMOVAL

Degaussing coils 8

Spring tension 9

C board 3

VM board 4

Neck assy 5

Deflection yolk 6

Anode cap 1

7 DGC holder

2 Chassis assy

10 Four PT screws

Picture tube 11

Cushion

• REMOVAL OF ANODE-CAP

Note : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode.

* REMOVING PROCEDURES.

Anode button

Turn up one side of the rubber cap in the direction indicated by the arrow a

• HOW TO HANDLE THE ANODE-CAP

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b

3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c

1 To prevent damaging the surface of the anode-cap do not use sharp materials. 2 Do not apply too great a pressure on the rubber, as this may cause damage to

the anode connector .

3 A metal fitting called a shatter hook terminal is fitted inside the rubber cap.

Do not turn the rubber foot over excessively this may cause damage if the shatter hook sticks out.

REMOVAL AND REPLACEMENT OF THE MAIN-BRACKET BOTTOM PLATES.

For safety reasons, on no account should the plates be

removed and not refitted after servicing.

(1) REMOVING THE PLATES

In the event of servicing being required to the solder side of the D Board printed wiring board, the bottom plates fitted to the main chassis bracket require to be removed. This is performed by cutting the gates with a sharp wire cutter at the locations indicated by arrows.

Note :There are 4 plates fitted to the main bracket and secured by 4 gates.

Only remove the necessary plate to gain access to the printed wiring board.

(2) REFITTING THE PLATES

Because the plates differ in size it is important that the correct plates are refitted in their original location.

Please note that the plates need to be rotated 180 degrees from the cut position to allow the tabs to be fitted in the catch positions.

Catch

Tab

SECTION 3

SET-UP ADJUSTMENTS

• When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments.

• Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply.

• Unless there are specific instructions to the contrary, set the controls and switches to the following settings:

Contrast ............... normal

Brightness ............... normal

3-1.BEAM LANDING

Preparation:

1. In order to reduce the influence of geomagnetism on the set’s picture tube, face it in an easterly or westerly direction.

2. Switch on the set’s power and degauss with the degausser.

(1) Adjustment of Correction Magnet for Y-Splitting

Axis

1. Input a crosshatch signal from the pattern generator.

2. Set the Picture control to minimum and confirm that the Brightness control is set to normal.

3. Position the neck assembly as indicated in Fig.3-2.

4. Move the deflection yolk as far forward as is possible.

5. Adjust the upper and lower pin symmetrically by opening or closing the Y-splitting axis correction magnets located on the neck assembly.

6. Return the deflection yolk to its original position.

Carry out the following adjustments in this order:

3-1. Beam Landing 3-2. Convergence 3-3. Focus 3-4. White balance

Note: Test equipment required

1. Color bar/pattern generator.

2. Degausser.

3. Digital multimeter.

4. Oscilloscope.

(2) Landing

Note :Before carrying out the following adjustments

adjust the magnets as indicated below [See Fig.3-3].

1. Input an all-white signal from the pattern generator. Maximize the picture setting and adjust the Brightness setting.

2. Rough-adjust the focus and horizontal convergence.

3. Loosen the deflection yolk screws and align the purity adjustment knob to its central position. [See Fig.3-1].

4. Switch from the all-white pattern to an all-green pattern.

5. Move the deflection yolk backwards and adju st with the purity magnet so that the green is at the centre and it aligns symmetrically. [See Fig.3-4].

6. Move the deflection yolk forward and adjust so that the entire screen becomes green.

7. Switch the raster signal to red, then to blue and verify the landing condition.

8. When the position of the deflection yolk has been determined, fasten the deflection yolk with the screw.

9. If the beam does not land correctly in all the corners of the screen, use magnets to correct it. [See Fig.3-5].

Y-splitting axis correction magnet

Caution :

High voltages are present on the Deflection yolk terminals - take care when handling the Deflection yolk whilst carrying out adjustments.

Purity

Fig.3-1

Deflection yoke

Align the bottom edge of the neck assy with the G3 hole centre.

Fig.3-3

Align Pips on each

magnet

Neck assy

Fig.3-2

GREEN

Center dot

RED

BLUE

Fig.3-4

H.STAT

convergence

control

V.S TAT

vertical static magnet

Disk magnets or rotatable disk

Purity control corrects this area.

magnets correct these areas (a-d).

H.STAT VR on

mount side RV5376

Screen (G2)

H.STAT convergence

• If the horizontal dots are unable to coincide with the variable range of the H.STAT convergence, adjust together with the

Deflection yoke positioning corrects these areas

V.STAT convergence while tracking. [Adjust the convergence by tilting the V.STAT convergence or by opening and closing the V.STAT convergence.]

(Open)

(Close)

Fig. 3-5

3-2.CONVERGENCE

(1) Screen centre convergence

[Static convergence]

1. Input a dot signal from the pattern generator. Normalize the picture setting.

2. [Moving horizontally], adjust the H.STAT control so that the horizontal red, green and blue dots coincide at the centre of the screen.

3. [Moving vertically], adjust the V.STAT magnet so that the vertical red, green and blue dots coincide at the centre of the screen.

4. Movement of the red, green and blue dots by tilting the V.STAT magnet and by opening or closing the V.STAT magnet.

a). By opening or closing the V.STAT magnet, the red, green and

blue dots move as indicated below.

B G

b). By rotating the V.STAT magnet counter

clockwise, the red, green and blue dots move as

indicated below.

c). By rotating the V.STAT magnet clockwise, the red, green and

blue dots move in the direction indicated below.

HAMP

d). By opening or closing the V.STAT magnet, the red, green and

blue dots move in the direction indicated below.

Note : If the blue dot does not coincide with the red and

green points correct the points by using the BMC [Hexapole] magnet.

5. Correction for HMC [horizontal mis-convergence] and VMC [vertical mis-convergence] by using the BMC [Hexapole] magnet.

a). HMC correction by BMC [Hexapole] magnet and movement

of the electron beam.

HMC correction(A) HMC correction(B)

A < B

RG B

A > B

RGB

7. HTIL correction can be performed by adding a THL correction ASSY to the DY.

TLH correction Assy

4-057-714-01

HTIL

A = B

RG B

b). VMC correction by BMC [Hexapole] magnet and movement

of the electron beam.

VMC correction(A) VMC correction(B)

C < D

C D

C = D C > D C = D

R G

A = B

R G

RG B

Layout of each control

3-3.FOCUS

Purity magnet BMC (Hexaploe) magnet V STAT convergence magnet Y-splitting axis correction magnet

Fig 3-5

Note : If you are unable to adjust the corner convergence

properly, this can be corrected with the use of permalloys.

1. Receive a television broadcast signal.

2. Normalize the picture setting.

3. Adjust the focus control located on the flyback transformer to obtain the best focus at the centre of the screen. Bring only the centre area of the screen into focus, the magenta-ring appears on the screen. In this case, adjust the focus to optimize the screen uniformly.

FOCUS

Permalloy Assy X-4387-214-1

a-d: screen-corner convergence defect

3-4.SCREEN (G2), WHITE BALANCE

[Adjustment in the service mode using the remote commander]

G2 adjustment (RV5376)

1. Input a dot signal from the pattern generator.

2. Set the Picture, Brightness and Colour to minimum.

3. Apply 175V DC from an external power supply to the R, G and B cathodes of the CRT.

4. Whilst watching the picture, adjust the G2 control RV5376 [SCREEN] located on the C Board to the point just before the flyback return lines disappear.

Convergence adjustment with permalloy

White balance adjustment for TV mode

Backend

1. Input an all-white signal.

2. Enter into the Service Mode by pressing ‘TEST’, ‘TEST’ and ‘MENU’ ‘MENU’on the Service Commander.

3. Select ‘Backend’ from the on screen menu display and press ‘OK’.

4. The ‘Backend’ menu wi ll appear on the screen.

5. Set the contrast to MAX.

6. Set the ‘R DRIVE’ to 41.

7. Adjust the ‘G DRIVE’ and ‘B DRIVE’ so that the white balance becomes optimum.

8. Press the ‘OK’ button to write the data for each item.

9. Set the contrast to MIN.

10. Set the ‘R CUT-OFF’ to 31.

11. Adjust the ‘G CUT-OFF’, and ‘B CUT-OFF’ with the left and right buttons on the remote commander so that the white balance becomes optimum.

12. Press the ‘OK’ button to write the data for each item.

No D escr. Def Min Max Data

1R-on ONOFFONON 2G-on ONOFFON ON 3 B-on ON OFF ON ON 4 D-col OFF OFF ON ON 5Color-axis 2032 6Contrast 6306363 7Limit-Luv 3033 8Hue 3106331

9Colour 3106328 10CTI -Level 2032 11 Brightness 31 0 63 31 12Gamma 2032 13 Sharpness 31 0 63 44 14LTI-Level 0030 15 R-Drive 41 0 63 40 16 BLK-Bottom 0030 17G-Drive 41063 38 18ABL-TH 0030 19 B-Drive 41 0 63 21 20ABL-Mode 2032 21 Sub Bright 31 0 63 32 22VM-Level 2032 23 R-Cutoff 31 0 63 41 24Preover 2032 25 G-Cutoff 31 0 63 45 26DPIC-Level 2032 27 B-Cutoff 31 0 63 48 28DC-Tran 1031 29 Sub-Cont 7 0 15 7 30 LRGB2-Lvl 12 0 15 12 31 P-Abl 15 0 15 15 32 DL-Pass OFF OFF ON OFF 33 Sharp.Fo ON OFF ON ON 34 Aging-W OFF OFF ON OFF 35 Aging-B OFF OFF ON OFF 36 CB-offset1 7 0 15 7 37 CR-offset1 7 0 15 7 38 CB-offset2 7 0 15 7 39 CR-offset2 7 0 15 7 40 Sub Colour 0 -8 8 -1

SECTION 4

CIRCUIT ADJUSTMENTS

4-1.ELECTRICAL ADJUSTMENTS

Service adjustments to this model can be performed using the supplied Remote Commander RM-891.

HOW TO ENTER INTO SERVICE MODE

1. Turn on the main power switch of the set while pressing PROG + (plus) and PROG - (minus) buttons on the top panel.

–

CONTROL

2. "TT" will appear in the upper right corner of the screen.

3. Press the ‘MENU’ button twice on the remote commander to obtain the service menu on the screen.

SERVICE MENU

Initialising Reset Devices Monitoring Backend Deflection Dynamic Convergence

PROGR

RESET DEVICES

Backend Deflection Dynamic Convergence Colour Decoder 1 Colour Decoder 2 Feature Box PIP Sound

Colour Decoder 1 Colour Decoder 2 Feature Low - End PIP Special Adjustment

Select :

Next Menu

INITIALISING

Model Setting Basic Setting Feature Setting

MONITORING

Device Status monitor Error Monitor Production Monitor NVM Monitor Line 23 Monitor

4. Push the joystick up or down on the remote commander to select the adjustment item.

5. Push the right button to proceed to the next menu.

6. If the required adjustment item is ‘Deflection’, push the down button to move to ‘Deflection’.

7. Push the joystick to the right to enter into ‘Deflection’.

8. Change the data in order to comply with each standard.

NOTE:

• Before performing any adjustments assure that the correct model has been selected in the Model Setting menu.

• After carrying out the service adjustments, to prevent the customer accessing the Service Menu switch the TV set OFF and then ON.

Model Setting

Backend

1 KV-29FX60A/D/E 2KV-29FX60B 3KV-29FX60U 4 KV-29FC60A/D/E 5 KV-29FC60B 6 KV-29FC60K 7 KV-29FC60R 8 KV-29FS60A/D/E

9KV-29FS60B 10 KV-29FS60K 11 KV-29FS60R 12 KV-28/32FX60A/D/E 13 KV-28/32FX60B 14 KV-28/32FX60K 15 KV-28/32FX60R 16 KV-28/32FX60U 17 KV-29FS60A/D/E 18 KV-29FS60B

Fig.4-1

Basic setting

No Descr. Min Max Data

1 Sys.B/G OFF ON ON 2 Sys.D/K OFF ON ON 3Sys.L OFFON ON 4 Sys I (UK) OFF ON OFF 5 Sys I (IRL) OFF ON OFF 6 Russian sound OFF ON OFF 7 TXT Nod.option 1 4 3 8 simple PAT OF F ON O FF

9 16:9 CRT OFF ON OFF 10 Sub-woofer OFF ON ON 11 Auto stand - by OFF ON ON 12 comb-filter OFF ON OFF 13 Auto YC det OFF ON ON 14 Auto comb det OFF ON OFF 15 AV2 Available OFF ON ON 16 AV3 Available OFF ON ON 17 AV4 Available OFF ON OFF 18 AV3 Front & rear OFF ON ON 19 SECAM Tape OFF ON OFF

No D esc r. Def Min Max Data

1R-on ONOFFONON 2G-on ONOFFON ON 3 B-on ON OFF ON ON 4 D-col OFF OFF ON ON 5Color-axis 2032 6Contrast 6306363 7Limit-Luv 3033 8Hue 3106331

Fig.4-3

Fig.4-2

NOTE:

The above table is dependant on model, destination & size.

Feature setting

Deflection

No Descr. Min Max Data

1PIP OFFON ON

Fig.4-4

Colour Decoder 1

No Descr. Def Min Max Data

1 DelayLinMd OFF OFF ON OFF 2Gain set 1031 3 Y-Delay 7 0 15 7 4Phase Time 0030 5 Vid Ident Md OFF OFF ON OFF 6 Sync Mode OFF OFF ON OFF 7 Vid Ident Sw ON OFF ON ON 8 H-Output OFF OFF ON OFF

9 Enagating OFF OFF ON OFF 10 IF Circuit ON OFF ON ON 11 GP Delay OFF OFF ON OFF

No Descr. Def Min Max Data

1 V-Size 31 0 63 34 2V-Position 3106321 3V-Comp 1031 4 V-Linear 7 0 15 7 5S-Corr 7 0158 6 H-Size 31 0 63 29 7 EW-DC OFF OFF ON OFF 8 Pin-Amp 31 0 63 36

9Up-Cpin 3106335 10M-Pin 2032 11 Lo-Cpin 31 0 63 37 12 Trapezium 7 0 15 7 13 H-Position 31 0 63 25 14 AFC-Bow 7 0 15 7 15 AFC-Angle 7 0 15 9 16 Up-Vlin 0 0 15 0 17 Lo-Vlin 0 0 15 0

Fig.4-7

Fig.4-5

Colour Decoder 2

No Descr. Def Min Max Data

1 DelayLinMd OFF OFF ON OFF 2Gain set 1031 3 Y-Delay 7 0 15 7 4Phase Time 0030 5 Vid Ident Md OFF OFF ON OFF 6 Sync Mode OFF OFF ON OFF 7 Vid Ident Sw ON OFF ON ON 8 H-Output OFF OFF ON OFF

9 Enagating OFF OFF ON OFF 10 IF Circuit ON OFF ON ON 11 GP Delay OFF OFF ON OFF

Fig.4-6

Dynamic Convergence

No Descr. Def Min Max Data

1 Range 63 0 63 32 2 H Stat 33 0 63 33 3 H amp L 37 0 63 37 4 H amp R 36 0 63 36 5Up Y 3106331 6Low Y 3306333 7Y Up L 3006330 8Y Up R 3006330

9Y Low L 3106331 10 Y Low R 30 0 63 3 0 11Mbow Up L 3106331 12Mbow Up R 3206332 13 Mbow Low L 32 0 63 32 14 Mbow Low R 32 0 63 32 15 V Stat 32 0 63 32 16 Linearity 128 0 255 104 17 H Centre 32 0 63 32 18 H Trap 32 0 63 32 19 Rotation 0 0 255 0 20 Focus Phase 128 0 255 128

Fig.4-8

Feature Low-End

Feature Low-End(Cont.)

No Descr. Def Min Max Data

1 F.S.F.M OFF OFF ON OFF 2 G-Mode OFF OFF ON OFF 3 Picture Pos 0 0 3 0 4 Comp Mode OFF OFF ON OFF 5 CompSW OFF OFF ON OFF 6 Acqu.freq OFF OFF ON OFF 7 Still Pic OFF OFF ON OFF 8 Init OFF OFF ON OFF

9 Dis Feature ON OFF ON ON 10 Dis Vlimit ON OFF ON ON 11 Scr Fade 0 0 3 0 12 Hwe Delay 20 0 255 20 13 Auto Vshift OFF OFF ON OFF 14 Vwe Delay 0 0 127 0 15 SFR sw OFF OFF ON OFF 16IPQ 0030 17 D.Col Dec OFF OFF ON OFF 18 Blankfield 0 0 15 0 19 P1.5 OFF OFF ON OFF 20 P1.4 OFF OFF ON OFF 21 P1.3 OFF OFF ON OFF 22 P1.2 OFF OFF ON OFF 23 P1.1 OFF OFF ON OFF 24 Set Vdba OFF OFF ON OFF 25 Set Sidep ON OFF ON ON 26 Set Hwe OFF OFF ON OFF 27 Set Clv OFF OFF ON OFF 28 Set Hddel OFF OFF ON OFFF 29 Set Hblnd OFF OFF ON OFF 30 Set Hre ON OFF ON ON 31 Set Hbda ON OFF ON ON 32 Set Hdav ON OFF ON ON 33 Vbdasta 0 0 255 0 34 Vsdasto 0 0 255 0 35 Msbhwesto OFF OFF ON OFF 36 Msbhwesta OFF OFF ON OFF 37 Msbvbdasto OFF OFF ON OFF 38 Msbvbdasta OFF OFF ON OFF 39 Hdavsta 40 0 255 40 40 Hdavsto 255 0 255 255

No Descr. Def Min Max Data

41 Hbdasta 223 0 255 223 42 Hbdasto 222 0 255 222 43 Hresta 38 0 255 38 44 Hresto 202 0 255 202 45 Hblndsta 31 0 255 31 46 Hblndsto 30 0 255 30 47 MsbHblndsta OFF OFF ON OFF 48 MsbHblndsto OFF OFF ON OFF 49 Msb Hresto ON OFF ON ON 50 Msb Hresta OFF OFF ON OFF 51 Msbhbdasta ON OFF ON ON 52 Msbhbdasto ON OFF ON ON 53 Msbhdavsto ON OFF ON ON 54 Msbhdavsta OFF OFF ON OFF 55 Hddel 0 0 15 0 56 Clvsta 0 0 255 0 57 Clvsto 9 0 255 9 58 Hwesta 44 0 255 44 59 Hwesto 208 0 255 208 60 Ex-Thres OFF OFF ON OFF 61 Wes ON OFF ON OFF 62 Demo mode ON OFF ON OFF 63Limerick NR 0040 64 Nthr 0 0 255 2 65 Wval 200 0 255 200 66 Agc Ych 203 0 255 203 67 Agc Uvch 209 0 255 209 68 Aal-Bypass OFF OFF ON OFF 69 Stby Fr OFF OFF ON OFF 70 Lsb Agc-Uv OFF OFF ON OFF 71 Lsb Agc-Y OFF OFF ON OFF 72Vcl cor 0030 73Ucl cor 0030 74Uv cor mode 0030 75Uvcl tau 3033 76Uvcol Lvl 0030 77 Fil Mem OFF OFF ON OFF 78Overl Thr 1031 79Y delay f 4074 80 Dcti pdxsel ON OFF ON ON

Fig.4-9

Feature Low-End (Cont.)

PIP

No Des cr. Def Min Max Data

81 Dcti Thres 0 0 15 0 82Dcti Gain 0070 83 Dcti Super ON OFF ON ON 84 Dcti Fil ON OFF ON ON 85 Dcti Prot ON OFF ON ON 86 Dcti Sep ON OFF ON ON 87Dcti Limit 2032 88Peak Beta 0070 89Peak Alpha 2072 90Peak Neg g 0030 91Peak Delta 0030 92Peak Tau 0070 93 Peak Corth 0 0 15 0 94Overlay V 0 0150 95Overlay U 0 0150 96 Overlay Y 10 0 255 10 97 Sidep sta 240 0 255 240 98 Sidep sto 36 0 255 36

99Y delay B 7077 100 Invert UV ON OFF ON ON 101 Output Range ON OFF ON ON 102Sidep Fdel 0030

No Descr. Def Min Max Data

1 Freeze OFF OFF ON OFF 2Frame ONOFFONON 3Pipon ONOFFONOFF 4 Seldel 1 0 15 1 5 Mixdis ON OFF ON ON 6H-Poshi 0030 7 H-Pos 137 0 255 137 8 V-Pos 59 0 255 59

9Y-Delay 0070 10 V-Dec OFF OFF ON OFF 11 H-Dec OFF OFF ON OFF 12 Insvh ON OFF ON ON 13 Chrins ON OFF ON ON 14Pmod 0030 15Imod 0030 16 Clisw ON OFF ON ON 17 H side 4 0 15 4 18 Vsiisq OFF OFF ON OFF 19 Vsidel 0 0 31 0 20 Parasynd ON OFF ON ON 21 Vspisq OFF OFF ON OFF 22 Vspdel 10 0 31 10 23Con 1 0151 24Fry 8 0158 25Frv 3 0153 26Fru 4 0154 27 Sel Down OFF OFF ON OFF 28Frwidv 1031 29Frwidh 2072 30Mat 4074 31 Daconst OFF OFF ON OFF 32Plltc 1031 33 Dacontle OFF OFF ON OFF 34 Left 83 0 255 83 35RightHi 1031 36 Right 192 0 255 192 37 Up 46 0 255 46 38 Down 189 0 255 189

Fig.4-10

+ 92 hidden pages