Sony KP-43T70K, KP-43T70T, KP-48VS70K, KP-53VS70K, KP-53VS70T Service manual

SERVICE MANUAL

RA-3

CHASSIS

MODEL COMMANDER DEST. CHASSIS NO.

–––––– –––––––––––– ––––– –––––––––––

KP-43T70K
KP-43T70T
KP-48VS70K
KP-53VS70K
KP-53VS70T

RM-Y906K Korean SCC-P18AA

RM-Y906 Taiwan SCC-P20AA

RM-Y906K Korean SCC-P18BA

RM-Y906K Korean SCC-P18CA

RM-Y906 Taiwan SCC-P20BA

MODEL COMMANDER DEST. CHASSIS NO.

–––––– –––––––––––– ––––– –––––––––––

DVD/

SAT/

POWER

MUTING

VTR

CABLE

TV

FUNCTION

SYSTEM

OFF

DVD/VTR SAT/CABLE

TV

TV/VTR

FREEZE

SWAP PIP

m

N

M

AUDIO

POSITION ACTIVE

X

xz

ANT

TV/VIDEO

SLEEP

PICTURE

DISPLAYMTS/SAP

CC

MODE

2

1

3

5

6

4

8

7

9

JUMP

ENTER

0

INDEX

GUIDE

RESET

MENU

VOL CH

CODE SET

TV

RM-Y906/Y906K

KP-43T70K/43T70T KP-48VS70K/53VS70K/53VS70T

MICROFILM

∗ Please file according to model size. .......

43

48 53

COLOR REAR VIDEO PROJECTOR

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

SPECIFICATIONS

Projection system

3 picture tubes, 3 lenses, horizontal in-line system

Picture tube

7-inch high-brightness monochrome tubes (6.3 raster size),
with optical coupling and liquid cooling system

Projection lenses

High performance, large diameter hybrid lens F1.05

Television system

American TV standard

Channel coverage

VHF: 2–13/UHF: 14 –69/CATV: 1 – 125

Antenna

75 ohm external terminal for VHF/UHF
Screen size (measured diagonally)
43 inches (KP-43T70K/43T70T)
48 inches (KP-48VS70K)
53 inches (KP-53VS70K/53VS70T)

Inputs/outputs

VIDEO 1 IN
VIDEO 2 INPUT

S VIDEO IN (4-pin mini DIN):
Y: 1 Vp-p, 75-ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
VIDEO (phono jack): 1 Vp-p, 75-ohms unbalanced,
sync negative
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 47 kilohms

VIDEO 3 IN

S VIDEO IN (4-pin mini DIN):
Y: 1 Vp-p, 75-ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
VIDEO (phono jack): 1 Vp-p, 75-ohms unbalanced,
sync negative
Y: 1 Vp-p, 75 ohms, sync negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 47 kilohms

MONITOR OUT

VIDEO (phono jack): 1 Vp-p, 75-ohms
unbalanced, sync negative
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 470 ohms
AUDIO (VAR/FIX) OUT (phono jacks): 500 mVrms
(100% modulation), Impedance: 470 ohms

CONTROL S OUT: minijack

Speaker

100 mm (4”) x 2
Speaker output
15W x 2

Power requirement

120 V AC, 60 Hz (Taiwan model)
220 V AC, 60 Hz (Korean model)

Power consumption

In use (Max.): 160 W
In standby: 1 W

Dimensions (W/H/D)

965 x 1,058 x 510 mm (38 x 41 5/8 x 20 1/8 inches)
(KP-43T70K/43T70T)
1,105 x 1,338 x 579 mm (43 1/2 x 52 5/8 x 22 3/4 inches)
(KP-48VS70K)
1,216 x 1,417 x 632 mm (47 7/8 x 55 3/4 x 24 7/8 inches)
(KP-53VS70K/53VS70T)

Mass

65 kg (143 lbs 5 oz) (KP-43T70K/43T70T)
70 kg (154 lbs 5 oz) (KP-48VS70K)
77 kg (169 lbs 12 oz) (KP-53VS70K/53VS70T)

Supplied accessories

Remote control RM-Y906K (1) (Korean model),
RM-Y906 (1) (Taiwan model)
Batteries (2) size AA (R6)

Optional accessories

Connecting cables
RK-G34, RK-74A, RK-G69HG, VMC-10HG,
VMC-720M, VMC-810S/820S, YC-15V/30V
U/V mixer EAC-66

Design and specifications are subject to change without notice.

– 2 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

SELF DIAGNOSIS FUNCTION

1. Summary of Self-Diagnosis Function

• This device includes a self-diagnosis function.

• In case of abnormalities, the TIMER/STANDBY indicator automatically blinks. It is possible to predict the abnormality location
by the number of blinks. The Instruction Manual describes blinking of the TIMER/STANDBY indicator.

• If the symptom is not reproduced sometimes in case of a malfunction, there is recording of whether a malfunction was generated
or not. Operate the remote command to confirm the matter on the screen and to predict the location of the abnormality.

2. Diagnosis Items and Prediction of Malfunction Location

• When a malfunction occurs the TIMER/STANDBY indicator only blinks for one of the following diagnosis items. In case of two
or more malfunctions, the item which first occurred blinks. If the malfunctions occurred simultaneously, the item with the lower
blink count blinks first.

• The screen display displays the results regarding all the diagnosis items listed below. The display “ 0 ” means that no malfunc­tions occurred.

metisisongaiD

NOtonrewoP•0

noitcetedPCOB+semit2.tiucrichcaenimetsysylppusrewopfotiucrictrohS

noitcetedPVOB+semit3

potsnoitcelfedlacitreVsemit4

noitcetedytilamronbatuooediVsemit5

potsnoitcelfedlatnoziroHsemit6

noitcetedytilamronbaoiduAsemit8

YBDNATS/REMIT

retacidnI

sknilbforebmuN

.nepo106F
.nepo706R

.nepo276R

.tiucric

noitcnuflamdesoppuSnoitidnoC

]metsySylppuSrewoPybdnatS[

tiucrictrohs106Q

]metsySylppuSrewoPniaM[

.nekorbera216Rdna106CI

tiucric-trohs106RDV

.nepo87nip306T

.nekorbsi)tuoV(9051CI

.nekorbsi)reffuBesluPV(5051Q

)draobA(022,912,812Q

.nepo615,515C

.nekorbsi)elgnuJCY(602CI

.nekorbsi).pmaoiduA(604CI

.nepo204,104SP

draobCnisrehtodna167,237,507Q,tuooediV

.rewopehtnonruttonnaC

.knilbt'nseodDEL

edomybdnatsehtotseoG

enilB+fotiucrictrohS

edomybdnatsehtotseoG

tiucricylppusrewopfonoitcnuflaM

.detumsilangis

.sisongaidflesehtrofsknilbnehtdna

.raeppat'nseodretsaR000potSH:6

.tuotonsidnuosehT

edomybdnatsehtotseoG

oedivnehtdnaA,yllatnozirohenilenootseogretsaR

,sdnoces03.xorppasknilbDELYBDNATS/REMIT

sisongaid-fleS

,yalpsidneercs

stluseR:metisisongaiD

000PCOB+:2

000PVOB+:3

000potSV:4

000BKA:5

000oiduA:8

* : 000 the range of values for number of operations is 000-255. For 256 or higher there is

no count up and the number remains at 255.

3. Blinking count display of TIMER/STANDBY indicator

* One blink is not used for self-diagnosis.

< FRONT PANEL >

VOLUME

–+

TV/VIDEO

FLASH FOCUS

CHANNEL

–+

POWER

•EXAMPLE

TIMER/STAND BY

<Diagnosis Items> <Number of Blinks>

• +B overcurrent 2 times

• +B overvoltage 3 times

TIMER/STANDBY indicator

• Vertical deflection stop 4 times

Lamp ON : 0.3 seconds
Lamp OFF : 0.3 seconds

Release of TIMER/STANDBY indicator blinking.

• The TIMER/STANDBY indicator blinking display is released by turning OFF the power switch
on the TV main unit or removing the plug from the power.

– 3 –

Lamp OFF :

3.0 seconds

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

4. Self-diagnosis screen displays

• In cases of malfunctions where it is not possible to determine the symptom such as when the power goes off occasionally or when
the screen disappears occasionally, there is a screen display on whether the malfunction occurred or not in the past (and whether
the detection circuit operated or not) in order to allow confirmation.

<Screen Display Method>

• Quickly press the remote command button in the following order from the standby state.

DISPLAY b Channel 5 b VOL – b POWER

˘
Be aware that this differs from the method of
entering the service mode (volume + ).



Self-diagnosis screen display

Self Check

2 : +B OCP 000
3 : +B OVP 000
4 : V Stop 000
5 : AKB 000
6 : H Stop 000
7 : HV 000
8 : Audio 000
101 : WDT 000

÷

2 : +B OCP 000

Diagnosis

Results

000 the range of values for number of

operations is 000-255.
For 256 or higher there is no count up
and the number remains at 255.

5. Self-Diagnosis Screen Display

• The results display is not automatically cleared. In case of repairs and after repairs, check the self-diagnosis screen and be sure
to return the results display to “ 0 ”.

• If the results display is not returned to “ 0 ” it will not be possible to judge a new malfunction after completing repairs.

<Method of Clearing Results Display>

1. Power off (Set to the standby mode)

2. DISPLAY b Channel 5 b VOL + b POWER (Service Mode)

3. Channel 8 b ENTER (Test reset = Factory preset condition)

<Method of Ending Self Diagnosis Screen>

• When ending the self-diagnosis screen completely, turn the power switch OFF on the remote commander or the main unit.

– 4 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

6. Self-diagnosis function operation

OCP Low B and +B line detect DET SHORT, and shut-down POWER ON RELAY.

Reset by turning power on/off.
In case of +B is loaded approx. 1.3A or more, microcomputer detects it via IC651.

OVP In case of +B becomes approx. 150V or more, POWER ON RELAY shuts down and microcomputer detects it via IC651.

Reset by turning power on/off just the same as OCP.

V Stop In case of microcomputer detects 2 seconds or more interval of V Pulse, Reference Pulse turns off by turning off the picture

signal in YC Jungle IC (IC206).

After the picture signal turns off, V Pulse is regenerated 2 seconds or more, the picture signal turns on.
AKB IK detection. Makes LED blinking in case of microcomputer doesn’t detect IK returns of IC206 CXA2147Q 30 seconds or more.
H Stop In case of HV becomes 33kV or more, IC502 detects it and shut-down H Drive Pulse.

Microcomputer receives H Stop data from IC206 and makes LED blinking.
Audio In case of DC component overlaps the output of Audio Amp., microcomputer detects it and makes LED blinking.

Microcomputer forces to shut down the power.

Self-diagnosis block diagram

8

20 21 22

55

IC002

µProcessor

TIMER/STANDBY

IC064

EEPROM

Audio AMP

5. AKB

6. H STOP

49
47
50
48

IC406

D1201

BUS

5. AKB

Q006

3
4

IC206

CXA2147

YCJ

43
35
34

6. HV STOP

IC1502

HV Detector

27

IC1509
V Drive

Q1505

V Pulse Buffer

C Board

4. V.STOP (V Pulse)

3. OVP

2. OCP

Audio

IC651
OVP Buffer
OCP Buffer

DC Detect

OVP DETECT

OCP DETECT

– 5 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

TABLE OF CONTENTS

Section Title Page
–––––– –––– ––––

SELF DIAGNOSIS FUNCTION............................................ 4

1. GENERAL

Remote Control ....................................................................... 7

Precautions .............................................................................. 7

Installing and Connecting the Projection TV.......................... 8

Basic Set Up .......................................................................... 12

Using Your New Projection TV ............................................ 13

Adjusting Your SET UP (menus) .......................................... 16

Operating Video Equipment.................................................. 21

Operating a Cable Box .......................................................... 22

Troubleshooting .................................................................... 23

2. DISASSEMBLY

2-1. Rear Board Removal ................................................. 24

2-2. Chassis Assy Removal .............................................. 24

2-3. Service Position ......................................................... 24

2-4. HA Board and HB Board Removal

(Except KP-43T70K/43T70T) .................................. 24

2-5. HA Board and HB Board Removal

(KP-43T70K/43T70T) .............................................. 25

2-6. Mirror Cover Removal .............................................. 25

2-7. Beznet Assy Removal ............................................... 25

2-8. HC Board and S Board Removal .............................. 25

2-9. A ,G and FA Boards Removal ................................... 26

2-10. Picture Tube Removal ............................................... 26

2-11. High-Voltage Cable Installation and Removal .......... 26

3. SET-UP ADJUSTMENTS

3-1. Screen Voltage Adjustment (Rough Alignment) ....... 27

3-2. Focus Lens Adjustment ............................................. 27

3-3. Screen (G2) Adjustment ............................................ 27

3-4. Focus VR Adjustment ............................................... 27

3-5. Deflection York Tilt Adjustment ............................... 28

3-6. 2-Pole Magnet Adjustment (Green, Red) .................. 28

3-7. 4-Pole Magnet Adjustment........................................ 28

3-8. Defocus Adjustment (Blue) ....................................... 28

3-9. Electrical Adjustment by Remote Commander ......... 29

3-10. Registration Adjustment ............................................ 34

3-11. Auto Registration Error Code List ............................ 37

4. SAFETY RELATED ADJUSTMENTS

4-1. HV Regulation Circuit Check and Adjustment ......... 38

4-2. HV Hold Down Circuit Operation and Adjustment .. 38

4-3. +B Max Voltage Confirmation .................................. 38

4-4. +B OVP Confirmation .............................................. 39

Section Title Page
–––––– –––– ––––

5. CIRCUIT ADJUSTMENTS

5-1. TV Input Sub Contrast Adjustment
5-2. Video Input Sub-HUE and Sub-Color Adjustment
5-3. Component Input Sub-HUE and SubColorAdjustment

5-4. P & P Sub Contrast Adjustment (SC-SYDR)............ 40

5-5. Sub-HUE, Sub-Color and Main Contrast Adjustment

5-6. Bar Display Position Adjustment (OP-DISP) ........... 41

5-7. PIP Position Adjustment (PI-PIPH, PIPV)................ 41

(VPNT-SCON) .......................................................... 40

(VPNT-SHUE, SCOL) .............................................. 40

(DAC-UVSH, UVSC) ............................................... 40

(MC-MYDR, MSHU, MSCL, SC-SSHU, SSCL) .... 41

7. DIAGRAMS

6-1. Block Diagram (1) ..................................................... 43

Block Diagram (2)..................................................... 45

Block Diagram (3)..................................................... 51

Block Diagram (4)..................................................... 55

Block Diagram (5)..................................................... 57

6-2. Frame Schematic Diagram ........................................ 61

6-3. Circuit Boards Location ............................................ 64

6-4. Printed Wiring Boards and Schematic Diagrams ...... 64

• A (1/3)Board ....................................................................... 65

• A (2/3)Board ....................................................................... 69

• A (3/3)Board ........................................................... 73

• G Board................................................................... 81

• CG Board ................................................................ 88

• CR Board ................................................................ 88

• CB Board ................................................................ 89

• HA Board ................................................................ 91

• HC Board ................................................................ 91

• HB Board ................................................................ 92

• FA Board ................................................................. 93

6-5. Semiconductors ......................................................... 94

7. EXPLODED VIEWS

7-1. Cover (KP-43T70K/43T70T) .................................... 96

7-2. Cover (KP-48VS70K) ............................................... 97

7-3. Cover (KP-53VS70K/VS70T) .................................. 98

7-4. Chassis (KP-43T70K/43T70T) ................................. 99

7-5. Chassis (Except KP-43T70K/43T70T) ................... 100

7-6. Picture Tube ............................................................ 101

8. ELECTRICAL PARTS LIST ................................. 102

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE

(CAUTION)

ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CAR­BON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.

WARNING!!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE­CAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTL Y CONNECTED
TO THE AC POWER LINE.

SAFETY -RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE

PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESECOMPONENTS WITH SONY P ARTS WHOSE PART NUM­BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE­MENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFEOPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITI­CAL COMPONENTS ARE REPLACED OR IMPROPER OPERA­TION IS SUSPECTED.

– 6 –

Remote Control

In the instructions that follow,
we will refer to the buttons on
your remote control.
Keep this flap unfolded and use
this page for reference.

operation buttons

Taiwan Model
* The blue-labeled SAT/

CABLE (POWER), SAT/
CABLE (FUNCTION),
INDEX and GUIDE
buttons cannot operate a
satellite receiver (SAT) in
Taiwan (the Republic of
China) even if it is
connected to the projection
TV.

MUTING

(page 14)

SYSTEM OFF

(page 16)

VCR/DVD/MDP

(page 31)

SLEEP

(page 16)

PICTURE MODE

(pages 14, 20)

CC

(page 16)

0 – 9 buttons

(page 14)

JUMP

(page 15)

(pages 16, 21)

INDEX*

(pages 17, 20, 21)

RESET

VOL +/–

(page 14)

CODE SET

(pages 30, 32)

SECTION 1

GENERAL

The operating instructions mentioned here are partial abstracts from the
Operating Instructions Manual. The page numbers of the Operating
Instruction Manual remain as in the manual. (Part no : 3-867-647-31)

POWER*

DVD/

SAT/

VTR

FREEZE

m

SLEEP

CC

CABLE

FUNCTION

SWAP PIP

N

AUDIO

xz

ANT

2
5
8
0

3
6
9

ENTER

POWER

TV

TV

M

TV/VIDEO

DISPLAYMTS/SAP

GUIDE

MENU

MUTING

SYSTEM

OFF

DVD/VTR SAT/CABLE

TV/VTR

POSITION ACTIVE

X

PICTURE

MODE

1
4
7

JUMP

INDEX

/

RESET

VOL CH

CODE SET

(pages 14, 31, 32)

FUNCTION*

(pages 14, 31, 32)

PIP operation
buttons

(page 17)

TV/VIDEO

(pages 15, 17)

ANT

(page 16)

DISPLAY

(page 15)

BILINGUAL

(Korean model)

MTS/SAP

(Taiwan model)
(pages 16, 21)

ENTER

(page 14)

GUIDE

*

V/v/B/b and

buttons

(page 19)

MENU

(page 19)

CH +/–

(page 14)

TV

Getting to know the buttons on the
remote control

Names of the buttons on the remote control are
presented in different colors to represent the
available functions.

Button color

Transparent .... Press to select the component

you want to control; e.g. VTR
(VCR)/MDP/DVD Player,
CABLE, or projection TV.

Green ............... Buttons relevant to power

operations, like turning the
projection TV, CABLE, or VTR
(VCR)/MDP/DVD Player on
or off

Label color

White ............... TV/VTR (VCR)/MDP/DVD

Player/CABLE operation

buttons

Yellow .............. PIP operation buttons

Blue .................. SAT operation buttons*

Green ............... S-Link operation buttons

Pink .................. DVD Player operation buttons

For a detailed explanation of most buttons, see
“Watching the TV” on page 14.

Precautions

Installing and Connecting the Projection TV (continued)

Safety

• Operate the projection TV only on 120 V
AC.

• The plug is designed, for safety purposes,
to fit into the wall outlet only one way. If
you are unable to insert the plug fully
into the outlet, contact your dealer.

• If any liquid or solid object should fall
inside the cabinet, unplug the projection
TV immediately and have it checked by
qualified service personnel before
operating it further.

• If you will not be using the projection TV
for several days, disconnect the power by
pulling the plug itself. Never pull on the
cord.

2

Note on cleaning

Clean the cabinet of the projection TV with a
dry soft cloth. To remove dust from the
screen, wipe it gently with a soft cloth.
Stubborn stains may be removed with a cloth
slightly dampened with solution of mild
soap and warm water. Never use strong
solvents such as thinner or benzine for
cleaning.

If the picture becomes dark after using the
projection TV for a long period of time, it
may be necessary to clean the inside of the
projection TV. Consult qualified service
personnel.

Installing

• To prevent internal heat buildup, do not
block the ventilation openings.

• Do not install the projection TV in a hot
or humid place, or in a place subject to
excessive dust or mechanical vibration.

• Avoid operating the projection TV at
temperatures below 5° C (41° F).

• If the projection TV is transported
directly from a cold to a warm location,
or if the room temperature changes
suddenly, the picture may be blurred or
show poor color. In this case, please wait
a few hours to let the moisture evaporate
before turning on the projection TV.

• To obtain the best picture, do not expose
the screen to direct illumination or direct
sunlight. It is recommended to use spot
lighting directed down from the ceiling
or to cover the windows that face the
screen with opaque drapery. It is
desirable to install the projection TV in a
room where the floor and walls are not of
a reflective material.

– 7 –

Installing and Connecting the Projection TV

20°

20°

min. 1.5m (approx. 5ft.)

43"

min. 2.1m (approx. 7ft.)

53"

Carrying Your Projection TV

Carrying the projection TV requires three or
more people.

For KP-53VS70T

The projection TV has been equipped with
casters for easy movement on a hard surface.
Please move your projection TV using the
casters.

Installing the Projection TV

Recommended viewing area
(Horizontal)

min. 2.1m (approx. 7 ft.)

min. 1.5m (approx. 5 ft.)

60°

60°

53"

43"

Recommended viewing area
(Vertical)

3

Installing and Connecting the Projection TV (continued)

Connector Types

You may find it necessary to use some of the
following connector types during set up.

Coaxial cable

Standard TV cable and antenna cable

Plug Type

Push into connection.

Screw-on Type

Screw into connection.

S Video cable

High quality video cable for enhanced
picture quality

Audio/Video cable

Video - Yellow
Audio (Left) - White
Audio (Right) - Red

Some DVD Players are equipped with the
following three video connectors.

Y - Green
P

B (CB, Cb or B–Y) - Blue

P

R (CR, Cr or R–Y) - Red

4

Align guides and
push into connection.

Push into connection.

CONTROL S cable

Sony cable for CONTROL S connection. This
feature is exclusive to Sony products and
allow greater control of all Sony equipment.

Push into connection.

About the CONTROL S OUT jack

To control other Sony equipment with the
projection TV’s remote control, connect the
CONTROL S IN jack of the equipment to the
CONTROL S OUT jack on the projection TV
with the CONTROL S cable.

(Rear of projection TV)

AUX

TO

CONVERTER

IN

CONTROL S

OUT

CONTROL S

VIDEO 1 VIDEO 3

S VIDEO

VIDEO

L

(MONO)

AUDIO

R

OUT

COMPONENT

MONITOR AUDIO

Y

P

B

PR

OUT

(VAR/FIX)

VHF/UHF

VIDEO

L

(MONO)

AUDIO

R

Making Connections

Connecting directly to a cable or
an antenna

The connection you choose will depend on
the cable found in your home. Newer homes
will be equipped with standard coaxial cable
(see

A); older homes will probably have 300 -

ohm twin lead cable (see
homes may contain both (see C).
Use 75-ohm coaxial cable for improved
picture quality (see

A

• VHF only
or

• VHF/UHF
or

• Cable

B

• VHF only
or

• UHF only
or

• VHF/UHF

B); still other

A).

75-ohm
coaxial cable

300-ohm twin
lead cable

Antenna connector

(Rear of

projection TV)

VHF/UHF

(Rear of

projection TV)

VHF/UHF

– 8 –

C

S VIDEO

VIDEO

AUDIO

L

R

VIDEO

VHF/UHF

AUX

(MONO)

IN

VIDEO 1 VIDEO 3

OUT

MONITOR AUDIO

(VAR/FIX)

TO

CONVERTER

Y

P

B

P

R

R

L

(MONO)

AUDIO

COMPONENT

LINE

OUT

OUT

IN

AUDIO R AUDIO L VIDEO

S VIDEO

VHF/UHF

LINE

IN

75-ohm coaxial cable

• VHF

(Rear of

projection TV)

VHF/UHF

and

EAC-66 U/V mixer

• UHF

(not supplied)

300-ohm twin lead cable

Cable or antenna

This is the simplest connection. Connection is
made directly from the cable or antenna to
the projection TV.

(Rear of projection TV)

Coaxial cable

VHF/UHF

Cable and antenna

You may find it convenient to use the
following set up if your cable provider does
not feature local channels that you are able to
receive using an antenna.

(Rear of projection TV)

Coaxial cable

(No connection “TO
CONVERTER” in this case)

Antenna cable

AUX

TO CONVERTER

VHF/UHF

Select Cable or ANT mode by pressing ANT
on the remote control.

Connecting a cable box

Some pay cable TV systems use scrambled or
encoded signals that require a cable box* to
view all channels.

Also, set “Cable” to “On” in the Channel Set
Up menu (page 25).

(Rear of projection TV)

Coaxial cable

OUTIN

*Cable box

VHF/UHF

Cable box and cable

Some pay cable TV systems use scrambled or
encoded signals requiring a cable box* only for
certain channels.

*Cable box

Scrambled
channels

75-ohm coaxial cable
(not supplied)

CATV cable

(unscrambled channels)

For this set up, you can switch between
scrambled channels (through your cable
box), and normal (CATV) channels by
pressing ANT on your remote control.

Notes:

• You may be able to program your Sony

remote control to operate your cable box.
(see “Operating a Cable Box” on page 32)

• During PIP or Favorite Channel viewing,

the AUX input can only be viewed in the
main picture.

(Rear of projection TV)

AUX

TO CONVERTER

(Signal)

VHF/UHF

5

Installing and Connecting the Projection TV (continued)

Connecting a cable TV system/
antenna to a VCR

1 Attach the coaxial cable from the

incoming cable connection or antenna to
VHF/UHF IN on the VCR.

2 Using a coaxial cable, connect VHF/UHF

OUT on the VCR to VHF/UHF on the
projection TV.

3 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the
VCR to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, Red­AUDIO Right**).

Connecting a VCR and projection
TV to a cable box

1 Connect the single (input) jack of the

splitter to the incoming cable connection,
and connect the other two (output) jacks
(using the coaxial cable) to IN on the cable
box and VHF/UHF on the projection TV.

2 Using a coaxial cable, connect OUT on the

cable box to VHF/UHF IN on the VCR.

3 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the
VCR to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, Red­AUDIO Right**).

6

Disconnect all power sources before making any connections.

(Rear of projection TV)

Coaxial cable

2

VCR

Cable/
Antenna

1

1

VCR

VHF/UHF

OUT

IN

OUT

IN

Cable/
Antenna

2

S VIDEO

VIDEO

AUDIO-L

AUDIO-R

VMC-810S/820S
(not supplied)

YC-15V/30V

(not supplied)

3

(Rear of projection TV)

AUX

CONVERTER

IN

VIDEO 1 VIDEO 3

S VIDEO

VIDEO

L

(MONO)

AUDIO

R

S VIDEO

COMPONENT

VIDEO

AUDIO-L

AUDIO-R

MONITOR AUDIO

Y

B

P

P

R

OUT

(VAR/FIX)

VHF/UHF

VIDEO

L

(MONO)

AUDIO

R

VMC-810S/820S
(not supplied)

YC-15V/30V

Coaxial cable

TO

LINE

LINE
OUT

(not supplied)

AUDIO R AUDIO L VIDEO

IN

Splitter (not supplied)

S VIDEO

Cable box

3

– 9 –

Note:

S VIDEO

VIDEO

L

(MONO)

R

AUDIO

VIDEO 2 INPUT

• To view scrambled channels through the
cable box, select the video input which the
cable box is connected to by pressing TV/
VIDEO.

* If your VCR is not equipped with S VIDEO, use a

VIDEO cable (yellow) instead of the S VIDEO
cable.

** If you are connecting a monaural VCR, connect

only the single audio output to the left (MONO)
input on the projection TV.

Connecting a camcorder

Use this connection to view a picture directly
from your camcorder.

1 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the
camcorder to AUDIO and S VIDEO IN
inside the drop-down panel on the front
of the projection TV (White-AUDIO Left,
Red-AUDIO Right**).

2 Press VIDEO 2 to select the video inputs

from a camcorder.

* If your camcorder is not equipped with S

VIDEO, use a VIDEO cable (yellow) instead of
the S VIDEO cable.

** If you are connecting a monaural camcorder,

connect only the single audio output to the left
(MONO) input on the projection TV.

Disconnect all power sources before making any connections.

YC-15V/30V (not supplied)

Audio/
video
outputs

Camcorder

S VIDEO
OUT

S VIDEO

(Front of projection TV)

VMC-810S/820S
(not supplied)

VIDEO
AUDIO-L
AUDIO-R

7

Installing and Connecting the Projection TV (continued)

Connecting two VCRs for tape
editing

By connecting a second VCR to MONITOR
OUT, you can record a program being played
by the primary VCR to the second VCR or
perform tape editing and dubbing.

1 Connect the VCR intended for playback

using the connection instructions on page
6 of this manual.

2 Using an AUDIO/VIDEO cable, connect

AUDIO and VIDEO IN on the VCR
intended for recording to AUDIO and
VIDEO OUT of MONITOR OUT on the
projection TV.

Notes:

• Do not change the input signal while
editing through MONITOR OUT.

• When connecting a single VCR to the
projection TV: if VCR LINE OUT is
connected to VIDEO IN on the projection
TV, do not connect MONITOR OUT on
the projection TV to the VCR LINE
INPUT (see right). Doing so will cause
program interference and other viewing
problems.

8

VCR (for playback)

AUDIO R AUDIO L VIDEO

1

OUT

LINE

IN

OUT

VMC-810S/820S
(not supplied)

Disconnect all power sources before making any connections.

(Rear of projection TV)

AUX

TO

CONVERTER

IN

S VIDEO

VIDEO

AUDIO-L

AUDIO-R

(Rear of projectionTV)

VIDEO IN

VCR

VIDEO

L

(MONO)

AUDIO

R

VIDEO 1 VIDEO 3

MONITOR
OUT

IN

COMPONENT

LINE

OUT

MONITOR AUDIO

(VAR/FIX)

Y

B

P

P

R

VIDEO
AUDIO-L
AUDIO-R

Indicates direction
of signal

OUT

VHF/UHF

VIDEO

L

(MONO)

AUDIO

R

VMC-810S/820S
(not supplied)

VCR (for recording)

AUDIO R AUDIO L VIDEO

LINE

IN

2

OUT

IN

– 10 –

Connecting a DVD Player (Upper
illustration)

Using an AUDIO and S VIDEO cables,
connect AUDIO and S VIDEO IN on the
projection TV to AUDIO and S VIDEO OUT
on the DVD Player (White-AUDIO Left, Red­AUDIO Right).

Connecting a DVD Player with
component video output
connectors (Lower illustration)

1 Using an AUDIO cable, connect AUDIO of

LINE OUT on the DVD Player to AUDIO
of VIDEO 3 IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).

2 Using three yellow VIDEO cables, connect

Y, PB, and PR of COMPONENT VIDEO
OUT on the DVD Player to Y, P
VIDEO 3 IN on the projection TV.

Note:

• Some DVD Player terminals may be
labeled differently. If so, connect as
follows:

Connect Y (green) to Y.
Connect P
Connect P

B (blue) to CB, Cb or B-Y.
R (red) to CR, Cr or R-Y.

B, and PR of

S VIDEO

AUDIO-R

AUDIO-L

(Rear of
projection
TV)

Disconnect all power sources before making any connections.

(Rear of projection TV)

IN

VIDEO 1 VIDEO 3

S VIDEO

S VIDEO

VIDEO

L

(MONO)

AUDIO

R

VIDEO

L

(MONO)

AUDIO

R

Y

B

P

P

R

COMPONENT

RK-74A (not supplied)

YC-15V/30V (not supplied)

RK-74A (not supplied)

AUDIO-L

AUDIO-R

IN

VIDEO 1 VIDEO 3

Y

B

P

P

R

COMPONENT

PR
PB
Y

OUT

MONITOR AUDIO

(VAR/FIX)

OUT

MONITOR AUDIO

(VAR/FIX)

VIDEO

L

(MONO)

AUDIO

R

VIDEO

L

(MONO)

AUDIO

R

AUX

TO

CONVERTER

VHF/UHF

AUX

TO

CONVERTER

VHF/UHF

VMC-10HG
(not supplied)

LINE OUT

R–AUDIO 1–L VIDEO

LINE OUT

R–AUDIO 1–L VIDEO

S VIDEO OUT

DVD

S VIDEO OUT

S-LINK

DIGITAL OUT

OPTICAL COAXIAL

Audio/S video
outputs

Connect the DVD Player
directly to the projection TV.
Connecting the DVD Player
through other video
equipment will cause
unwanted picture noise.

DVD

S-LINK

COMPONENT VIDEO OUT

DIGITAL OUT

OPTICAL COAXIAL

R-YY B-Y

9

Installing and Connecting the Projection TV (continued)

Connecting an audio system

For more dynamic sound, connect an audio
system to the projection TV.

1 Using an AUDIO cable, connect AUDIO

(VAR/FIX) OUT on the projection TV to
one of the unused Line inputs (e.g. Tape­2, AUX1, etc.) on the stereo.

2 Set the stereo to the chosen Line input

and use the Audio menu to set the audio
output and switch the TV’s speakers off.
(see “Audio Out” and “Speaker” on page

22)

Note:

• You can adjust VOLUME, “Bass,”
“Treble,” “Balance,” “MTS/SAP” and
“Effect” with the supplied remote control.
The control items except VOLUME can be
adjusted only when “Audio Out” is set to
“Variable” in the Audio menu. (see
“Audio Out” on page 22)

10

Disconnect all power sources before making any connections.

(Rear of projection TV)

IN

VIDEO 1 VIDEO 3

S VIDEO

CONTROL S

VIDEO

L

(MONO)

AUDIO

R

OUT

COMPONENT

Y

P

P

MONITOR AUDIO

B

R

Stereo amplifier

OUT

(VAR/FIX)

AUDIO-L

VIDEO

L

(white)

(MONO)

AUDIO

R

AUDIO-R
(red)

RK-74A
(not supplied)

HRD

Line inputs

– 11 –

Connecting a Sony SAVA series
speaker system

Use this connection to control the speaker’s
Dolby* Pro Logic surround system and
super woofer mode with the remote control.
(see “SAVA SP Control” on page 22)

1 Using the AUDIO cable supplied with the

speaker to AUDIO (VAR/FIX) OUT on
the projection TV.

2 Using the CONTROL S cable, connect

CONTROL S IN on the speaker to
CONTROL S OUT on the projection TV.

* Manufactured under license from Dolby

Laboratories Licensing Corporation.
Additionally licensed under Canadian patent
number 1,037,877. “Dolby,” the double-D
symbol a and “Pro Logic” are trademarks of
Dolby Laboratories Licensing Corporation.

(Rear of projection TV)

CONTROL S

OUT

CONTROL S
OUT

Disconnect all power sources before making any connections.

SAVA series

speaker system

IN

VIDEO 1 VIDEO 3

S VIDEO

VIDEO

L

(MONO)

AUDIO

R

RK-G34, etc. (not supplied)

COMPONENT

Y

P

P

OUT

MONITOR AUDIO

(VAR/FIX)

VIDEO

B

(MONO)

AUDIO

R

AUDIO-R (red)

L

R

AUDIO-L
(white)

Audio cord supplied
with the speakers

1 IN L

1

1 IN R

CONTROL S IN

2

11

Basic Set Up

Using the Remote Control

Inserting the batteries

Insert two size AA (R6) batteries (supplied)
by matching the + and – on the batteries to
the diagram inside the remote control’s
battery compartment.

Notes:

• Remove the batteries to avoid damage
from possible battery leakage whenever
you anticipate that the remote control
will not be used for an extended period.

• Handle the remote control with care.
Avoid dropping it, getting it wet, or
placing it in direct sunlight, near a heater
or where the humidity is high.

• Your remote control can be programmed to
operate most video equipment.
(see “Operating Video Equipment” on
page 30)

12

Setting Up the Projection TV
Automatically

The AUTO SET UP feature will allow you to
set the on-screen language and set all
receivable channels.

The AUTO SET UP feature does not apply for
installations that use a cable box for all channel
selection.

You can also set up the projection TV manually.
(see “Using the Channel Set Up menu” on pages
24 and 25)

Notes:

• Before you perform AUTO SET UP again,
make sure that the input from ANT (not
AUX) is selected by pressing ANT until
“AUX” does not appear next to the
channel number.

• Perform this function during the day, with
the antenna and/or cable properly
connected, to ensure that all available
channels will be broadcasting and
receivable.

• When you perform AUTO SET UP, all the
settings in the Video, and Audio menus
are reset to the factory settings.

Using the buttons on the front panel and
inside the drop-down panel on the projection
TV:

Front panel:

FLASH FOCUS

TV/VIDEO

–+

CHANNEL

–+

POWER

TIMER/STAND BY

VOLUME

Inside the drop-down panel:

FLASH FOCUS

TV/VIDEO

MENUSET UP

1 Press POWER to turn on the projection TV.

POWER

2 Press SET UP inside the drop-down panel.

The AUTO SET UP screen appears.

[CH+]

[CH–]
[VOL+]
[VOL–]

SET UP

English :
Español :
Français :
Auto Set Up :

First please connect
cable/antenna.

Press [ SET UP ] to exit.

– 12 –

3 Press CHANNEL + to select English,

CHANNEL – to select Español or
VOLUME + to select Français.

The screen will change to reflect your choice.

VOLUME

–+

–+

CHANNEL

English :
Español :
Français :
Auto Set Up :

Primero conecte el
cable/antena.

Oprima [ SET UP ] para
salir.

[CH+]

[CH–]
[VOL+]
[VOL–]

4 Press VOLUME – to continue.

VOLUME

–+

Continue to

Auto Program ?

[CH+]

Yes :

[CH–]

No :

5 Press CHANNEL + to preset channels

automatically.

CHANNEL

–+

Auto Program

“Auto Program” appears and the
projection TV starts scanning and
presetting channels automatically. While
scanning, the received channel will be
displayed on the sub screen. When all the
receivable channels are stored, the lowest
numbered channel is displayed.

To perform AUTO SET UP again

Press SET UP inside the drop-down panel on
the projection TV and perform steps 3-5 on
pages 12 and 13.

Press SET UP again to exit.

Adjusting the Convergence
Automatically (FLASH FOCUS)

The projection tube image appears on the
screen in three layers (red, green and blue). If
they do not converge, the color is poor and
the picture blurs.

Before you use your projection TV, be sure to
adjust the convergence.

The FLASH FOCUS feature allows you to
adjust the convergence automatically.

z

Tips

• It is recommended to perform FLASH FOCUS about
30 minutes after the projection TV is first turned on.

• You can also perform FLASH FOCUS using the Set
Up menu on page 29.

FLASH FOCUS

Press FLASH FOCUS.

The cross pattern appears and FLASH
FOCUS begins to work. The adjustment is
completed when the cross pattern becomes
white.

Note:

• FLASH FOCUS is canceled if you
perform any other function while FLASH
FOCUS is working.

13

Using Your New Projection TV

Using Your New Projection TV (continued)

Watching the TV

Many TV features can be accessed directly
through the remote control. The following
chart will explain the function of some
buttons found on your remote control.

Using the White Labeled Buttons for Projection TV Operations

TV (FUNCTION)
TV POWER

-

0 9

and ENTER

CH +/–

VOL +/–
MUTING

14

Activates the remote control for use with the projection TV.
Turns the projection TV on and off. If a video input indication (e.g., VIDEO 1,

VIDEO 2) appears on the screen, press TV/VIDEO until a channel number
appears.

Use for direct channel selection. Press 0-9 to select a channel (for example,
to select channel 10, press 1 and 0). The channel will change after 2
seconds, or you can press ENTER for immediate selection.

Press to scan through the channels (+ up or – down).

Speed Surf
1 Press and hold CH + or – to change the channel number rapidly.
2 Release to display the desired channel.

Press to adjust the volume (+ up or – down).
Press to mute the sound. “Muting” will appear on the screen and will dim

three seconds later. To restore sound, press again or press VOL +.

PICTURE MODE

Press PICTURE MODE repeatedly to directly
choose one of five different video modes that
best suits the program you are watching.
Vivid: Select for enhanced picture contrast and

sharpness.

Standard: Select to display a standard

picture for normal viewing environments.

Movie: Select to display a finely detailed

picture for low light environments.

Personal 1, Personal 2: Select to customize

the “Picture Adjustment” of the Video menu
according to your personal preference.

When you select “Movie,” “Personal 1” or
“Personal 2,” you can also perform the “Picture
Adjustment” (such as “Brightness,” “Color,” etc.)
to suit your taste. For details, see “Mode” on
page 20.

– 13 –

Using the White Labeled Buttons for Projection TV Operations

TV/VIDEO

JUMP

FREEZE

(yellow labeled
button)

DISPLAY

Press repeatedly to scroll through available video inputs:
TV, VIDEO 1, VIDEO 2 and VIDEO 3.
If you select “Skip” as a “Video Label” in the Set Up menu, your projection
TV will skip the video input you selected. (see “Video Label” on page 29)

Press to alternate or

jump

back and forth between two channels. The
projection TV will jump between the current channel and the last channel
selected using the 0-9 buttons.

This is useful when you need to copy down information that appears on the
TV’s screen.
Press to

freeze

the desired picture. The frozen picture is displayed in the
window picture while viewing the normal picture of the current channel in the
main picture.

Reciipe
flour - - - - 2
sugar - - - 1/2
salt - - - - - 1/2
butter - - - 1

6

Frozen picture

Normal motion
picture

To change the location of the window picture, press V, v, B or b.
Press FREEZE again to display the normal picture.

Press to display the channel number, current time, channel caption (if set),
and MTS/SAP mode (if SAP is selected). The SAP indication disappears and
the other indications dim three seconds later.
To turn the display off, press DISPLAY again.

REFER TO THE

ILLUSTRATION OF THE

REMOTE CONTROL ON THE

INSIDE FRONT COVER OF

THIS MANUAL AS YOU

REVIEW THIS CHART

(continued)

15

Using Your New Projection TV (continued)

Using the White Labeled Buttons for Projection TV Operations

CC

SLEEP

ANT

(AUX input)

MTS/SAP

TV/VTR

SYSTEM OFF

16

Press repeatedly to scroll through available displays:

XDS (Extended Data Service)

Displays a network name, program name, program type, program length,
program description, call letters and time of the show if the broadcaster
offers this service.

Caption Vision

Displayed on the screen if the broadcaster offers this service. (see
“Caption Vision” on page 28)

No display

“Off” appears and the display is canceled.

Press repeatedly until the projection TV displays the approximate time in
minutes (30, 60, or 90) that you want the projection TV to remain on before
shutting off automatically.
Cancel by pressing until “Sleep Off” appears.

Press to change between the VHF/UHF input and the AUX input. (for
detailed connection information, see “Cable and antenna” or “Cable box and
cable” on page 5)

Press to scroll through the Multi-channel TV Sound (MTS) options:
Stereo, SAP, Mono and Auto SAP. (see “MTS/SAP” on page 21)

Press to select an audio option:
Simulated, Surround, BBE and Effect Off. (see “Effect” on page 21)

Press when you are finished using a VCR and you want to switch to the TV
input. The VCR power will remain on.

Press to turn off the projection TV and all other Sony equipment.

REFER TO THE

ILLUSTRATION OF THE

REMOTE CONTROL ON THE

INSIDE FRONT COVER OF

THIS MANUAL AS YOU

REVIEW THIS CHART

– 14 –

Watching Two Programs at One Time — PIP

The Picture-in-Picture (PIP) feature allows
you to view two channels simultaneously,
one in the full size “main” picture and one in
a smaller “window” picture.

You can move the window picture to any
location on the screen.

The symbol “b” or “B”
indicates which picture's
TV channel or input
source can be changed.

Main
picture

* It will dim in about 3 seconds.

Tip

z

If you press RESET in PIP mode, the window picture
will move to the bottom right (factory-preset location).

The symbol “≥”
indicates which
picture's sound is being
received.

TV channel or input­source mode for the

6

main picture* (yellow­green-colored)

10

TV channel or input­source mode for the
window picture*

Window
picture

(white-colored)

PIP

POSITION

ACTIVE

TV/VIDEO

(white labeled
button)

Using the Yellow Labeled Buttons for PIP Operations

Press to display a window picture.
Each time you press this button, the picture size will change
(1/9 n1/16 nno display).

To close the window picture, press PIP repeatedly until it disappears.
Press POSITION repeatedly to change the location of the window picture

(counterclockwise) around the main picture.

or

You can also change the location by pressing the V, v, B or b button.
The window picture moves in the direction of the arrow indicated on the
pressed button.

Press to select either the main or window picture in order to change the
TV channel or video source using the white labeled buttons below. The
symbol “b” (or “B”) will appear to indicate which picture’s channel or input
mode can be changed.

Press repeatedly to scroll through the available video inputs for the
picture on which the symbol “b” (or “B”) is displayed. (see “TV/VIDEO” on
page 15)

17

Using Your New Projection TV (continued)

CH

or or

0 9

and ENTER

(white labeled button)

ANT

(white labeled
button)

AUDIO

FREEZE

SWAP

18

Using the Yellow Labeled Buttons for PIP Operations

Press to select the TV channel on which the symbol “b” is

-

JUMP

Press to change between the VHF/UHF input and the AUX input for the picture on
which the symbol “b” (or “B”) is displayed.

Press to alternate sound between the main picture and the window picture. The
symbol “ ” will appear for a few seconds to indicate which picture’s sound is being
received.

This is useful when you need to copy down information of the main picture.
Press to freeze the desired scene in the main picture. The frozen picture is displayed
in the window picture while viewing the normal picture in the main picture. The
window picture size is automatically changed to 1/9 if it was 1/16.
Press again to resume normal PIP viewing.

Press to switch the audio and video of the main picture and the window picture.
Each time you press SWAP, the picture and sound of the two will be exchanged.

displayed. (for details, see “Watching the TV” on page 14)

Speed Surf
1 Press and hold CH + or – to change the channel number rapidly.
2 Release to display the desired channel.

REFER TO THE

ILLUSTRATION OF THE

REMOTE CONTROL ON THE

INSIDE FRONT COVER OF

THIS MANUAL AS YOU

REVIEW THIS CHART

Note:

• If one of the pictures received through
PIP is snowy, the entire screen may
become unstable. In this case, erase the
snowy channel. (see “Channel Skip/
Add” on page 25)

– 15 –

Move Select Exit

MENU

Set Up

Caption Vision: CC1
Language: English
Video Label
Flash Focus: No

ch

Adjusting Y our SET UP (menus)

Learning Menu Selection

Use the MENU button to access a menu and
use the V, v, B, b and
settings. Use the following example to learn
how to modify settings.

1 Press the MENU button.

The main menu appears.

MENU

2 Press V or v to highlight the desired menu

and press

You may also press b to activate your
selection.

buttons to alter the

Video

Mode: Vivid
Picture Adjustment
Trinitone: High

ch

Move Select Exit

to activate it.

Set Up

Caption Vision: CC1
Language: English
Video Label
Flash Focus: No

ch

Move Select Exit

MENU

MENU

3 Press V or v to highlight the desired

option.

4 Press .

Options for your selection (Pop-up menu
or Adjusting menu) will be displayed.

Pop-up menu Adjusting menu

Set Up

Caption Vision: CC1
Language: English
Video Label
Flash Focus: No

ch

Move Select

Español

Français

Exit

MENU

Video Label
VIDEO1:
VIDEO2:
VIDEO3:

Move Select Exit

VIDEO1
VIDEO2
VIDEO3

5 Press V or v to make your selection and

press
The previous screen will reappear.

to activate it.

Set Up

Caption Vision: CC1

Language: English
Video Label
Flash Focus: No

ch

Move Select Exit

Some adjustment menus may require
further operations. For details, see each
menu option.

To return to the previous screen (except
for the slider adjustment menus), choose
“

” at the bottom of the menu and press

or B.

6 Once you have completed all menu

corrections, press MENU to exit the menu
screens.

To exit from the menus at any

MENU

time

Press MENU.

z

Tip

You can also use the MENU, / and buttons
inside the front drop-down panel of the projection TV
for the menu selection.

MENU

MENU

19

Adjusting Y our SET UP (menus) (contin ued)

Using the Video Menu

Video

Mode: Vivid
Picture Adjustment
Trinitone: High

ch

Move Select Exit

For detailed information on using the remote
control to modify menu settings, refer to
“Learning Menu Selection” on page 19.

To select the Video menu:

Display / Highlight / Select

MENU

To restore the factory settings

Press RESET on the remote control while the
Video menu is selected. To restore each
“Mode” to the factory setting, press RESET
after selecting the mode to be reset.

20

MENU

Mode

Customized
picture viewing

Picture
Adjustment

Picture adjustment

Trinitone

White intensity
adjustment

You can choose one of five different video modes that best suits the program you
are watching. You can also perform the “Picture Adjustment” (such as
“Brightness,” “Color,” etc.) for “Movie,” “Personal 1” or “Personal 2” to suit your
taste.

Vivid: Select for enhanced picture contrast and sharpness.
Standard: Select to display a standard picture for normal viewing

environments.

Movie: Select to display a finely detailed picture for low light environments.
Personal 1, Personal 2: Select to customize the “Picture Adjustment” of the

Video menu according to your personal preference.

Press PICTURE MODE on the remote control for direct selection of a “Mode
setting.

First select “Movie,” “Personal 1” or “Personal 2” from “Mode,” then highlight the
desired option using the V or v button and press to display the adjusting
slider of the selected option.
Picture: Adjust slider right (up) to increase picture

contrast; left (down) to decrease it.

Brightness: Adjust slider right (up) to brighten the

picture; left (down) to darken it.

Color: Adjust slider right (up) to increase color

intensity; left (down) to decrease it.

Hue: Adjust slider right (up) to increase the green

tones; left (down) to increase the red tones.

Sharpness: Adjust slider right (up) to sharpen the

picture; left (down) to soften it.

High: Select to give the white colors a blueish tint.
Medium: Select to give the white colors a neutral tint.
NTSC Standard: Select to give the white colors a reddish tint.

Personal 1
Picture

Brightness
Color
Hue

ch

Sharpness

Move Select Exit

– 16 –

”

MENU

MTS/SAP

Using the Audio Menu

Audio

Treble
Bass
Balance
MTS/SAP:
Auto Volume:

ch

Effect:
Speaker:
Audio Out:
SAVA SP Control

Move Select Exit

Surround

Variable

For detailed information on using the remote
control to modify menu settings, refer to
“Learning Menu Selection” on page 19.

To select the Audio menu:

Display / Highlight / Select

MENU

To restore the factory settings

Press RESET on the remote control while the
Audio menu is selected.

* The BBE is manufactured by Sony Corporation

under license from BBE Sound, Inc. It is covered
by U.S. Patent No. 4,638,258 and No. 4,482,866.
The word “BBE” and the BBE symbol are the
trademarks of BBE Sound, Inc.

Stereo

MENU

Sliders

}

On
On

Treble

Sound adjustment

Bass

Sound adjustment

Balance

Sound adjustment

MTS/SAP

Enjoy stereo,
bilingual and mono
programs.

Auto Volume

Adjust the sound
level.

Effect

Customizes
surround sound
effects based on the
program’s audio
type.

Adjust slider right (up) to increase high pitched sounds.
Adjust slider left (down) to decrease high pitched sounds.

Adjust slider right (up) to increase low pitched sounds.
Adjust slider left (down) to decrease low pitched sounds.

Adjust slider right (up) to emphasize right speaker volume.
Adjust slider left (down) to emphasize left speaker volume.

When the sound is intermittent due to poor reception conditions, select “Stereo”
or “SAP.”

Stereo: Select for stereo reception when viewing a program broadcast in stereo.
SAP: Select to listen to a bilingual broadcast. (non-SAP programs will be muted

when this feature is selected)

Mono: Select for mono reception. (use to reduce noise during stereo broadcasts)
Auto SAP: Select to listen to SAP when a SAP program is broadcast and return

to stereo reception automatically for non-SAP programs.

Quick MTS access: Press

“MTS/SAP” options as follows: Stereo n SAP n Mono n Auto SAP.

On:

Sound output coming from TV speakers have the volume level equalized for all

channel audio inputs when broadcasts have different sound transmission levels.

Off: Sound output coming from the TV speakers varies according to the received

channel.

“Effect” can only be set when “Speaker” is set to “On” or “Off.”

Simulated: Adds a surround-like effect to mono programs.
Surround: Simulates sound with the atmosphere of a movie theater or a concert

hall for stereo programs.

BBE*: Centers the sound intensity to the front, creating an effect as if you were

seated in front of an orchestra.

Off: Normal stereo or mono reception.

Quick Effect access: Press on the remote control to cycle through the

“Effect” options as follows: Simulated n Surround n BBE n Effect Off.

on the remote control to cycle through the

(continued)

21

Speaker

Custom selection
of audio output
source

Audio Out

Easy control of
volume adjustment

SAVA SP Control

Controls Sony
SAVA speaker’s
mode.

22

Adjusting Y our SET UP (menus) (contin ued)

On: Select to listen to the sound from the projection TV speakers alone.
Off: Select to turn off the projection TV speakers and listen to the

projection TV’s sound only through an external audio system’s speakers.

SAVA SP: Select to turn off the projection TV speakers and listen to the projection

TV’s sound only through the Sony SAVA series speaker system. You can
adjust volume, muting, “Surround Mode,” and “Super Woofer Mode” with the
projection TV’s remote control. (see “SAVA SP Control” below)

“Audio Out” can only be set when “Speaker” is set to “Off.”
Fixed: Sound output is held at a fixed level through the audio system.

Use the AV receiver’s remote control to adjust the volume.

Variable: Sound output varies according to the TV settings.

Useful when you want to use your remote control to control the output of a
separate audio system.

“SAVA SP Control” can only be set when Sony SAVA speaker system is
connected to the AUDIO (VAR/FIX) OUT connectors and “Speaker” is set to
“SAVA SP.” (see “Speaker” above)
You can also adjust the SAVA speaker’s volume using VOL +/– of the projection
TV’s remote control.

Surround Mode: Select to activate the SAVA Speaker’s surround mode.
Super Woofer Mode: Select to activate the SAVA Speaker’s super woofer mode.

– 17 –

Using the Timer Menu

Timer

Daylight Savings: Yes
Current Time
On / Off Timer

ch

----- : -AM-

Move Select Exit

After setting the clock you can use the timer
to turn the projection TV on and off.

For detailed information on using the remote
control to modify menu settings, refer to
“Learning Menu Selection” on page 19.

To select the Timer menu:

Display / Highlight / Select

MENU

Tip

z

Set daylight saving time before setting the clock. Any
loss of power will cause these settings to be erased.

MENU

Daylight Savings

Automatically
adjusts the time.

Current Time

Necessary for the
Timer.

On/Off Timer

Wake up or
scheduled viewing.

Spring: Select Yes to compensate for Daylight Saving Time.

The current time automatically moves ahead one hour.

Fall: Select No at the end of Daylight Saving Time.

The current time moves back one hour.

1 Press , then press V or v until the current day

(Sun-Sat) is displayed, and press .

2 Press V or v until the current hour (1-12) and

Current Time

––: –AM–

–––

AM/PM is displayed, and press .

3 Press V or v until the current minute (00-59) is

displayed, and press .

Move Select Exit

MENU

The clock has now started. Press MENU to exit.
1 Press V or v until the desired day or range of days

(Every Sun-Sat, Every Mon-Fri, Sunday, Monday, ...
Saturday, Every Sunday, ... Every Saturday) is
displayed, and press .

2 Press V or v until the time (hours and minutes) that

you want the projection TV to remain on is displayed,

On/Off Timer

––––––
––: ––AM–hch

Sun

12:00AM

Move Select Exit

–––

MENU

and then press .

3 Press V or v to set the time duration (maximum of 6 hours) and press .
4 Press V or v to select the desired channel and press .

The timer is now set. The TIMER/STAND BY indicator on your projection TV
will be lit.
Press MENU to exit. To cancel your timer setting, press RESET while in the On/
Off Timer window. Performing Auto Program will erase all Timer settings.

23

Adjusting Y our SET UP (menus) (contin ued)

ch

Using the Channel Set Up
Menu

Channel Set Up

Channel Caption
Favorite Channel :Auto
Channel Skip/Add
Auto Program
Cable: On

ch

Move Select Exit

For detailed information on using the remote
control to modify menu settings, refer to
“Learning Menu Selection” on page 19.

To select the Channel Set Up
menu:

Display / Highlight ch / Select

MENU

24

MENU

ch

Channel
Caption

Easy recognition
of the channel
you are watching

Favorite
Channel

User’s favorite
channels

You can add a caption for up to 32 channels of VHF/

UHF input.

With the Channel Caption window open:

Channel Caption

Channel: –––
Caption: – ––––

1 Press and then press V or v to select the desired

channel. You can view the channel that is selected
with the Channel Caption menu in the sub screen.

Move Select Exit

MENU

2 Press .
3 Press V or v to display the first letter or number of the

caption and press to select it.
Repeat until up to five digits are selected.

4 Press .

To erase a caption, press RESET.

The Favorite Channel feature enables easy access to the eight channels that you
preset (or the last channel that you were watching).
(for details on how to set up this feature, see “Setting and Selecting Favorite
Channel” on page 26)

– 18 –

Channel

Channel Skip/Add

Select a channel

2:
3:
4:
5:
6:
7:
8:

1:

Move Select Exit

MENU

9:

Skip
Skip

Add
Add
Add
Add
Add
Add
Add

ch

Favorite Channel

Select a position

2.

3.

4.

5.

6.

7.

8.

1.
2

10
20
30
40
50

100

1

SPTN

CNN

ch

Skip/Add

Skips unnecessary
channels.

Auto Program

Automatic
channel presetting

Cable

Cable system
setting

After AUTO SET UP, you can erase unnecessary
channels from the channel preset memory.
With the Channel Skip/Add window open:
1 Press V or v to select the desired channel. You can

view the channel that is selected with the Channel
Skip/Add menu in the sub screen. You can also use
CH +/– or 0–9 and ENTER buttons.

2 Press .
3 Press V or v to select Skip, and press .

The selected channel will be erased.
If you want to re-enter the skipped channel, follow the steps above and select
Add.

Select Yes to signal the projection TV to automatically program all receivable
channels. When all the receivable channels are stored, the lowest numbered
channel is displayed.
Select No to cancel Auto Program.

Select On if your projection TV is connected to a cable system.
Select Off if your projection TV is connected to an antenna.

25

Adjusting Y our SET UP (menus) (contin ued)

Setting and Selecting
Favorite Channel

The Favorite Channel feature of your
projection TV enables easy access to the eight
channels that you preset (or the last channel
that you were watching).

2 Press V or v to select “Manual” and press

.

The Favorite Channel menu will appear.
If you set Channel Caption names, they
will also be displayed. (see “Channel
Caption” on page 24)

Your Favorite Channel options can be set
automatically or manually.

The factory setting for “Favorite Channel” is
“Auto.”

When “Favorite Channel” is set to “Auto,”
the last eight channels selected with the 0–9
buttons will be set as Favorite Channel
options. If you want to input your own
selections as Favorite Channel settings, set to

3 Press V or v to select a position (1–8), and

press

.

“Manual.”

Favorite Channel

ch

1

CNN

Setting Favorite Channel manually

1 Select “Favorite Channel” from the

Channel Set Up menu. (see page 24)

Channel Set Up

Channel Caption
Favorite Channe: Auto
Channel Skip/Add
Auto Program
Cable: On

ch

Move Select Exit

26

Manual

MENU

1.

2.

3.

4.

5.

6.

7.
100

8.

Select a channel

– 19 –

2

SPTN

10
20
30
40
50

4 Press V or v to select a channel and press

.

You have now selected a favorite channel.

Favorite Channel

ch

1

CNN

1.
8

2.

SPTN

10

3.

20

4.

30

5.

40

6.

50

7.

100

8.

Select a channel

5 Use V and v to program other favorite

channels. (Follow steps 3 and 4.)

6 Press MENU when you have finished.

Your favorite channels are now ready for
use.

Changing Favorite Channel choices

You have the option of returning to the
Favorite Channel screen to adjust any of your
favorite channel choices.

Simply proceed as described in “Setting
Favorite Channel manually” (skip step 2 if
“Manual” is already selected).

When you reach step 3, select the position
you want to change and press
v to select a new channel.

Favorite Channel

ch

1.

6
2

2.
SPTN

10

3.

20

4.

30

5.

40

6.

50

7.

100

8.

Select a channel

Press MENU when you are done.

. Press V or

Using Favorite Channel

You can use the Favorite Channel feature to
directly select the channel you want to watch.

1 Press once.

The favorite channel menu and a window
picture will be superimposed over the
current channel. The window picture
displays the channel selected from the
menu.

1 CNN
2

SPTN

10
20
30
40
50

100

Exit

2 Press V or v to select the channel that you

wish to view from the menu.

The picture of the selected channel will be
displayed in the window picture.

1 CNN
2

SPTN

10
20
30
40
50

100

Exit

3 Press to select the channel.

The selected channel will be displayed for
normal viewing.

To cancel the favorite channel menu before
selecting a channel, press V or v to select
“Exit” at the bottom of the menu and press

.

27

Adjusting Y our SET UP (menus) (contin ued)

Using the Set Up Menu

Set Up

Caption Vision: CC1

Language: English

Video Label
Flash Focus: No

ch

Move Select Exit

For detailed information on using the remote
control to modify menu settings, refer to
“Learning Menu Selection” on page 19.

To select the Set Up menu:

Display / Highlight / Select

MENU

28

MENU

Caption Vision

Television closed
caption display

Language

Preferred
language

Some programs are broadcast with Caption Vision.
To display “Caption Vision,” select CC 1, CC 2,
CC 3, CC 4, TEXT1, TEXT2, TEXT3 or TEXT4 from
the menu. Then press the CC button until “Caption
Vision” is displayed.
CC 1, CC 2, CC 3 or CC 4 displays a printed

Set Up

Caption Vision: CC 1
Language:
Video Label
Flash Focus: No

ch

Move Select Exit

CC2
CC3

CC4
Text1
Text2
Text3
Text4

MENU

version of the dialogue or sound effects of a
program. (The mode should be set to CC 1 for most
programs.) TEXT1, TEXT2, TEXT3, or TEXT4
displays network/station information presented using
either half or the whole screen.

Notes:

• Poor reception of TV programs can cause errors in Caption Vision and XDS.
Captions may appear with a white box or other errors instead of the intended
text.

• XDS, Caption Vision, and the status display cannot be used at the same time.

Select from available languages (English, Español or Français) to display all
menus in your language of choice.

– 20 –

Video Label

Easy recognition of
connected
equipment
(e.g. DVD, VHS,
etc.)

This feature allows you to label each input mode so
that you can easily identify the connected equipment
(e.g. you can label VIDEO 1 IN as VHS).

With the Video Label window open:
1 Press V or v to select the input mode you want to

label and press .

2 Press V or v to select the label and press .

Video Label Options:

Video Label

VIDEO1:
VIDEO2:
VIDEO3:

Move Select Exit

Video Label
VIDEO1:

VIDEO2:
VIDEO3:

Move Select Exit

Video1

AV RECEIVER

VIDEO1
VIDEO2
VIDEO3

VHS
8mm
Beta

LD

DVD
Skip

MENU

MENU

VIDEO 1: VIDEO 1, VHS, 8mm, Beta, LD, DVD, AV RECEIVER, Skip
VIDEO 2/3: VIDEO 2/VIDEO 3, VHS, 8mm, Beta, LD, DVD, Skip

If you select “Skip,” your projection TV will skip this connection when you scan
through video sources using the TV/VIDEO button.

Flash Focus

Automatic
convergence
adjustment

Select Yes and press to start Flash Focus adjustment. When the
adjustment is completed, the cross pattern on the screen becomes white. (for
details, see page 13)
Select No to cancel Flash Focus.

Operating Video Equipment

Setting the Manufacturer's
Code

You can use the supplied remote control to
operate Sony or non-Sony video equipment
that has an infrared sensor.

Press CODE SET, DVD/VTR (FUNCTION),
and the 0-9 buttons to enter the
manufacturer’s code number (see the
following chart), then press ENTER.

For example, to operate a Sony 8mm VCR:

FUNCTION

CODE SET

DVD/VTR

3

0

If the remote control doesn’t work

• See the tips on page 32.

30

ENTER

2

VCR manufacturer code numbers

Manufacturer Code

Sony (VHS VCR) 301
Sony (8mm VCR) 302
Sony (Beta, ED Beta, VCRs) 303
Aiwa 338
Admiral (M. Ward) 327
Audio Dynamic 314, 337
Bell & Howell (M. Ward) 330
Broksonic 319, 317
Canon 309, 308
Citizen 332
Craig 302, 332
Curtis Mathis 304, 338, 309
Daewoo 341, 312, 309
DBX 314, 336, 337
Dimensia 304
Emerson 319, 320, 316, 317, 318, 341
Fisher 330, 335
Funai 338
General Electric 329, 304, 309
Go Video 340, 339, 322
Goldstar 332
Hitachi 306, 304, 305, 338
Instant Replay 309, 308
JC Penney 309, 305, 304, 330, 314, 336, 337
JVC 314, 336, 337
Kenwood 314, 336, 332, 337
LXI (Sears) 332, 305, 330, 335, 338
Magnavox 308, 309, 310
Marantz 314, 336, 337
Marta 332
Memorex 309, 335

29

Minolta 305, 304
Mitsubishi/MGA 323, 324, 325, 326
Multitech 325, 338, 321
NEC 314, 336, 337
Olympic 309, 308
Optimus 327
Panasonic 308, 309, 306, 307
Pentax 305, 304
Philco 308, 309
Philips 308, 309, 310
Pioneer 308
Quasar 308, 309, 306
RCA/PROSCAN 304, 305, 308, 309, 311,

Realistic 309, 330, 328, 335, 324, 338
Sansui 314
Samsung 322, 313, 321
Sanyo 330, 335
Scott 312, 313, 321, 335, 323, 324, 325, 326
Sharp 327, 328
Signature 2000 (M. Ward) 338, 327
Sylvania 308, 309, 338, 310
Symphonic 338
SV2000 338
Tashiro 332
Tatung 314, 336, 337
Teac 314, 336, 338, 337
Technics 309, 308
Teknica 338
Toshiba 312, 311
Wards 327, 328, 335, 331, 332
Yamaha 330, 314, 336, 337
Zenith 331

329, 312, 313, 310

– 21 –

MDP manufacturer code numbers

Manufacturer Code

Sony 701
Panasonic 704, 710
Mistubishi 702

DVD Player manufacturer code
numbers

Manufacturer Code

Sony 751
Panasonic 753
Pioneer 752
RCA 755
Toshiba 754

Tips

z

• In some rare cases, you may not be able to operate
your non-Sony video equipment with the supplied
remote control. In this case, please use the
equipment's own remote control.

• When you remove the batteries, the code number may
revert to the factory setting.

To operate video equipment

1 Press DVD/VTR (FUNCTION).
2 Use the VCR/DVD/MDP operation

buttons indicated in the following tables.

Operating a VCR using the remote control

To turn On/Off

To select a channel
To change channels
To record

To play
To stop
To fast forward
To rewind the tape
To pause

To search the
picture forward or
backward

To change input
mode

Press DVD/VTR (POWER).
[Green Button]

Press the 0 – 9 buttons.
Press CH +/–.
Press ( while pressing r.
Press (.
Press p.
Press ).
Press 0.
Press P. Press again to

resume normal playback.
Press ) or 0 during

playback. Release to
resume normal playback.

Press TV/VTR.

Operating an MDP using the remote
control

To turn On/Off

To play
To stop
To pause

Press DVD/VTR (POWER).
[Green Button]

Press (.
Press p.
Press P. Press again to

resume normal playback.

To search the picture
forward or backward

To search a chapter
forward or backward

Press ) or 0 during
playback. Release to resume
normal playback.

Press CH +/–.

Operating a DVD Player using the remote
control

To turn On/Off

To play
To stop
To pause

To step through
different tracks of
an audio disc

To step through
different chapters
of a video disc

To select tracks
directly

To display the
menu (Set up)

Press DVD/VTR (POWER).
[Green Button]

Press (.
Press p.
Press P. Press again to

resume normal playback.
Press ) to step forward or

0 to step backward.

Press CH + to step forward
or CH – to step backward.

Press 0-9 buttons.

Press MENU.

31

Operating a Cable Box

Setting the Manufacturer's
Code

You can program the supplied remote control
to operate a cable box.

Press CODE SET, SAT/CABLE
(FUNCTION)*, and the 0-9 buttons to enter
the manufacturer’s code number (see the
following chart), then press ENTER.

For example, to operate a Pioneer cable box:

FUNCTION

CODE SET

SAT/CABLE

2

1

Manufacturer code numbers
(cable box)

Manufacturer

Hamlin/Regal
Jerrold/G.I

Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith

32

222, 223, 224, 225, 226

201, 202, 203, 204, 205,

222, 206, 207, 208, 218

ENTER

4

Code

227, 228, 229
219, 220, 221

214, 215

209, 210, 211

216, 217
212, 213

To operate the cable box

1 Press SAT/CABLE (POWER)* [Green

Button] to turn on/off the cable box.

2 Press SAT/CABLE (FUNCTION)*.
3 For other operations, refer to the

operating instructions that come with the
equipment.

* The SAT/CABLE (POWER) and SAT/CABLE

(FUNCTION) buttons cannot operate a satellite
receiver (SAT) in Taiwan (the Republic of
China) even if it is connected to the projection
TV.

If the remote control doesn’t work

• Try repeating the set up procedures using
the other codes listed for your equipment.

To operate the projection TV

Press TV (FUNCTION). Then use the
projection TV control buttons to control the
projection TV.

Tips z

• If more than one code number is listed, try entering
them one by one until you come to the correct code
for your equipment.

• If you enter a new code number, the code number
you previously entered at that setting is erased.

• In some rare cases, you may not be able to operate
your equipment with the supplied remote control. In
this case, use the equipment’s own remote control
unit.

• Whenever you remove the batteries — to replace
them, for example — if too much time is taken, the
code numbers may revert to the factory setting and
must be reset.

– 22 –

Troubleshooting

If, after reading the following instructions, you have additional questions related to the use of your Sony projection TV, please contact your nearest Sony
dealer.

The picture turns off and the
TIMER/STAND BY indicator on the
front panel flashes (self-diagnosis
function)

No picture (screen not lit), no
sound

Remote control does not
operate

Dark, poor or no picture
(screen lit), good sound

Good picture, no sound

T roubleshooting (continued)

• The projection TV is equipped with a self-diagnosis function. If there is a problem with your projection TV, the TIMER/STAND BY indicator on the front
panel will flash repeatedly. Counting the number of flashes helps you inform qualified Sony personnel of the projection TV’s condition.

• Press POWER on the projection TV to turn it off, then inform qualified Sony personnel of the number of flashes.

• Make sure the power cord is plugged in.

• Operate with the buttons on both the projection TV and the remote control.

• Check to see if the TV/VIDEO setting is correct: when watching TV, set to TV, and when watching video tapes, set to VIDEO 1, 2, or 3.

• Try another channel.

• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

• Batteries could be weak. Replace the batteries.

• Press TV (FUNCTION) when operating your projection TV.

• Make sure the projection TV’s power cord is connected securely to the wall outlet.

• Locate the projection TV at least 3-4 feet away from fluorescent lights.

• Check the polarity of the batteries.

• Adjust “Picture” in the Video menu. (see “Picture Adjustment” on page 20)

• Adjust “Brightness” in the Video menu. (see “Picture Adjustment” on page 20)

• Check antenna/cable connections.

• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

• Adjust the convergence again using the FLASH FOCUS button. (see “Adjusting the Convergence Automatically (FLASH FOCUS)” on page 13)

• Press MUTING so that “Muting” disappears from the screen. (see “MUTING” on page 14)

• Check the MTS/SAP setting in the Audio menu. (see “MTS/SAP” on page 21)

• Make sure “Speaker” is set to “On” in the Audio menu. (see “Speaker” on page 22)

• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

It could be station trouble.

(continued)

33

Cannot receive upper channels
(UHF) when using an antenna

No color

Only snow and noise appear on
the screen

Dotted lines or stripes

TV is fixed to one channel
Double images or ghosts
Cannot operate the menu

Cannot receive any channels
when using cable TV

Cannot gain enough volume when
using a cable box

Favorite Channel does not display
your choices

Some video sources do not
appear when you press TV/VIDEO

Recording through MONITOR OUT
does not function properly when
recording in PIP mode

Cannot play shooting games

34

• Make sure “Cable” is “Off” in the Channel Set Up menu. (see “Cable” on page 25)

• Use “Auto Program” to add receivable channels that are not presently in the TV’s memory. (see “Auto Program” on page 25)

• Adjust “Color” in the Video menu. (see “Picture Adjustment” on page 20)

• Black and white programs cannot be seen in color.

• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

• Check the “Cable” setting in the Channel Set Up menu. (see “Cable” on page 25)

• Check the antenna/cable connections.

• Make sure the channel is broadcasting programs.

• Press ANT to change the input mode. (see “ANT” on page 16)

• Adjust the antenna.

• Keep the projection TV away from noise sources such as cars, neon signs or hair-dryers.

• Use “Auto Program” to add receivable channels that are not presently in TV’s memory. (see “Auto Program” on page 25)

• Use a highly directional outdoor antenna or a cable (when the problem is caused by reflections from nearby mountains or tall buildings).

• If the item you want to choose appears in gray, you cannot select it.

• Press the projection TV’s power button off and on again.

• Make sure “Cable” is “On” in the Channel Set Up menu. (see “Cable” on page 25)

• Use “Auto Program” to add receivable channels that are not presently in the TV’s memory. (see “Auto Program” on page 25)

• Increase the volume at the cable box. Then press TV (FUNCTION) and adjust the projection TV’s volume.

• Verify that “Favorite Channel” is set to “Manual” in the Channel Set Up menu. (see “Setting Favorite Channel manually” on page 26)

• Ensure that “Video Label” is not set to “Skip.” (see “Video Label” on page 29)

• MONITOR OUT will not record both images in PIP. Only the main picture will be recorded.

• If you are recording the main picture and you switch to the sound of the sub picture using the AUDIO button, the main picture will be recorded with sound
from the other program.

• Some shooting games which involve pointing a light beam at the TV screen with an electronic gun or rifle cannot be used with this projection TV. For
details, see the instruction manual supplied with the video game software.

– 23 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

SECTION 2

DISASSEMBLY

2-1. REAR BOARD REMOVAL 2-3. SERVICE POSITION

1 Disconnect CN203
on A board.

A board

G board

2 Rear board

From CG board CN1304.

(The extension cable is not
supplied because of the
countermeasure for radiation.)

CN203

2 Covers
Cut them off with a plier or the like
from chassis assembly in case of
checking printed circuit boards.
After checking, turn over the covers
and secure them with screws.

1 Nine screws (Except KP-43T70K/43T70T)
Eight screws (KP-43T70K/43T70T)
(Screw(4x20), tapping)

2-2. CHASSIS ASSY REMOVAL

1 Three screws
(Screw(4x20),tapping)

Chassis assembly

Screws
(+BVTP3x12)

2-4. HA BOARD AND HB BOARD REMOVAL

(EXCEPT KP-43T70K/43T70T)

6 Four screws
(+BVTP 4x12)

7 HB bracket

8 Three screws

(+BVTP 3x12)

9 HB board

2 Two screws

(+BVTP 4x12)

3 HA bracket
4 Multi button

5 HA board

2 Chassis assy

Speaker grille assy

1 Two screws
(Screws (4x20), tapping)

– 24 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

1 Three screws
(KP-43T70K/43T70T/48VS70K)
Five screws
(KP-53VS70K/53VS70T)
(Screws(4x20), tapping)

2 Eleven screws (KP-43T70K/43T70T)
Twelbe screws (KP-48VS70K)
Fifteen screws (KP-53VS70K/53VS70T)
(Screws(4x20), tapping)

3 Beznet assy

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

2-5. HA BOARD AND HB BOARD REMOVAL

(KP-43T70K/43T70T)

7 Three screws
(+BVTP 3x12)

1 Four screws

8 HB board

Panel ASSY , Control

(Screws (4x20), tapping)

2

3 Four screws

(+BVTP 3x12)

4 HA bracket
6 HA board

5 Three screws

(+BVTP 3x12)

2-7. BEZNET ASSY REMOVAL

2-6. MIRROR COVER REMOVAL

1 Seventeen screws
(KP-43T70K/43T70T)
Twenty four screws
(KP-48VS70K)
Nineteen screws
(KP-53VS70K/53VS70T)
(Screw(4x20), tapping)

2 Mirror cover

2-8. HC BOARD AND S BOARD REMOVAL

Sensor

Sensor
bracket (B)

bracket (A)

7 S board

6 Clows

4 Two screws

(+BVTP 4x12)

1 Two screws
(+BVTP 4x12)

2 L screen holder

3 HC board

5 Two screws

(+BVTP 4x12)

– 25 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

2-9. A, G AND FA BOARDS REMOVAL 2-11. HIGH-VOLTAGE CABLE INSTALLATION

!º FA board bracket

4 Eight screws

!¡ FA board

(+BVTP 3x12)

7 Two screws
(+BVTP 3x12)

3 Terminal board

9 A board

8 Claw

AND REMOVAL

(1) Remover

1 Rubber cap

2 HV cable

turn 90°

6 G board

Main bracket

5 Claws

2-10. PICTURE TUBE REMOVAL

CAUTION: Removing the arrow-marked

screws is strictly prohibited.
If removed, it may cause liquid spill.

2 Seven screws
(+BVTP 3x12)

1 Two screws
(Screws (4x20), tapping)

Lens
Picture tube

2 Four screws
(Screw(4x20), tapping)

(2) Installation

9 Tension
spring

1 HV cable
Hook

Gutter

4 Four screws
(Screw(4x20), tapping)

5 Lens
!º Four screws

(+BVTP 4x12)

!¡ Picture tube

3

8 Diflection yoke

7 Neck assy

6 CR board

1 Four screws

(Screw(4x20), tapping)

– 26 –

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

SECTION 3

SET-UP ADJUSTMENTS

3-1. SCREEN VOL T A GE ADJUSTMENT

(ROUGH ALIGNMENT)

1. Receive the Monoscope signal.

2. Set 50% BRIGHTNESS and minimum PICTURE.

3. Turn the red VR on the FOCUS block all the way to the left
and then gradually turn it to the right until the point where you
can see the retrace line.

4. Next gradually turn it to the left to the position where the
retrace line disappears.

R G B

SCREEN

R G B

FOCUS

FOCUS block

Fig. 3-1

3-2. FOCUS LENS ADJUSTMENT

In this adjustment, use the remote commander in the
service mode.
For details of the usage of the service mode and the remote
commander, please refer the item 3-9. ELECTRICAL
ADJUSTMENT BY REMOTE COMMANDER.

1. Loosen the lens screw.

2. Set to the service mode.

3. Change TV mode to the video input mode.

4. Set to PJE, and press 6 to display the test signal (crosshatch)“
on the screen.

5. Set VPNT 28 RON to “000”, 29 GON to “001” and 30 BON
to “000” to show only the green color.

6. Turn the green lens to adjust to the optimum focus point with
the test signal.

7. Tighten the lens screw.

8. Set VPNT 28 RON to “001”, 29 GON to “000” and 30 BON
to “000” to show only the red color.

9. Adjust red CRT lens just the same as green.

10. Set VPNT 28 RON to “000”, 29 GON to “000” and 30 BON
to “001” to show only the blue color.

11. Adjust blue CRT lens just the same as green.

*:Every time you press 6, the test signal changes to

“crosshatch+video signal” - “dots+video signal” ­“crosshach(black)” - “dots(black)” - off.

3-3. SCREEN (G2) ADJUSTMENT

1. Select VIDEO1 mode without signals.

2. Connect an oscilloscope to the TP701(KR), TP732(KG) and
TP761(KB) of CR board, CG board and CB board.

3. Adjust R, G and B screen voltage to 170 – 173V with screen
VR on the Focus block.

170 – 173V

GND

pedestal level

Fig. 3-3

3-4. FOCUS VR ADJUSTMENT

1. Set to the service mode.

2. Change TV mode to the video input mode.

3. Set to PJE, and press 6 to display the test signal (crosshatch)
on the screen.

4. Set VPNT 28 RON to “000”, 29 GON to “001” and 30 BON
to “000” to show only the green color.

5. Turn the green VR on the focus block to adjust to the optimum
focus point with the test signal.

6. Set VPNT 28 RON to “001”, 29 GON to “000” and 30 BON
to “000” to show the red color.

7. Turn the red VR on the focus block to adjust to the optimum
focus point with the test signal.

8. Set VPNT 28 RON to “000”, 29 GON to “000” and 30 BON
to “001” to show the blue color.

9. Turn the blue VR on the focus block to adjust to the optimum
focus point with the test signal.

Scanning line visible.

Test signal

Fig. 3-2

– 27 –

Lens

A

Minimize both A and B.

B

Center of crosshatch

Fig. 3-5Fig. 3-4

KP-43T70K/43T70T/48VS70K/53VS70K/53VS70T

RM-Y906K RM-Y906 RM-Y906K RM-Y906K RM-Y906

3-5. DEFLECTION YOKE TIL T ADJUSTMENT

1. Receive the Monoscope signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to
“000” to show only the green color.

4. Loosen the deflection yoke set screw and align the tilt of the
Deflection Yoke so that the bars at the center of the
monoscope pattern are horizontal.

5. After aligning the deflection yoke, fasten it securely to the
funnel-shaped portion (neck) of the CRT.

6. The tilt of the deflection yoke for red is aligned in the mode
VPNT 28 RON “001”, 29 GON “000”, 30 BON “000” on the
service mode menu, and the tilt of the deflection yoke for biue
is aligned with in the mode VPNT 28 RON “000”, 29 GON
“000”, 30 BON “001” on the service menu, is aligned the
same as was done for green.

4-pole magnet

2-pole magnet

Deflection yoke

Anode cap

Fig. 3-6

3-7. 4-POLE MAGNET ADJUSTMENT

1. Receive the Dot signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to
“000” to show only the green color.

4. Turn the green VR on the focus block to the left and set to
underfocus to enlarge the spot.

5. Now align the 4-Pole Magnet so that the enlarged spot
becomes a perfect circle for green and red.

6. Perform the same alignment for blue.

Use the center dot

x

/

x : y = 1:1.5 (BIue)
x : y = 1:1 (Green, Red)

Fig. 3-8

y

3-8. DEFOCUS ADJUSTMENT (BLUE)

1. Select the video menu and set the mode to “Vivid” mode.

2. Set to the service mode.

3. Change TV mode to the video input mode.

4. Set to PJE, and press 6 to display the test signal (dots) on the
screen.

5. Turn the blue VR on the focus block to adjust to the diameter
of the dots as shown in the figure below.

3-6. 2-POLE MAGNET ADJUSTMENT

(GREEN,RED)

1. Receive the Dot signal.

2. Set in service mode.

3. Set VPNT 29 GON to “001” 28 RON to “000” and 30 BON to
“000” to show only the green color.

4. Turn the green VR on the focus block to the right and set to
overfocus to enlarge the spot.

5. Now align the 2-Pole Magnet so that the enlarged spot is in the
center of the Just Focus spot.

6. Align the green focus VR and set for just (precise) focus.

7. Perform the same alignment for red.

Use the center dot

Fig. 3-7

[Focus adjustment point]

Inch

L

43"

6

Fig. 3-9

48"

7

Lmm Max

53"

8

– 28 –