See the PC Input Signal Compatibility Chart on page 27.
HDMI IN:
HDMI
Video: 480i, 480p, 576i, 576p, 720p, 1080i
Audio: Two channel linear PCM 32, 44.1 and
48 kHz, 16, 20 and 24 bits
AUDIO:
500 mVrms (100% modulation)
Impedance: 47 kilohms
Headphones i
Stereo minijack
Impedance: 16 ohms
/
//
/
Sound Output
KF-E50A10: 12 W + 12 W
KF-E42A10: 12 W + 12 W
Design and specifications are subject to change
without notice.
– 2 –
Page 4
KRM-GA004 RM-GA004
2193678
Overview of the TV buttons and indicators
To open the panel
To open the front panel of your TV,
WEGA GATE
PROG
push up the panel door just under
0
the mark.
KF-E42A10/E50A10
WEGA GATE
PROG
54
1 WEGA GATE
Displays WEGA GATE.
2
Confirms the selection or setting.
Selects the video equipment connected to the TV’s video inputs.
3 2 +/-/ /
Increases (+) or decreases (-) the volume.
In TV menu: Moves through the options left ( ) or right ( ).
4 PROG +/-/ /
In TV mode: Selects the next (+) or previous (-) channel.
In TV menu: Moves through the options up ( ) or down ().
5 indicator
Lights up in amber when the Sleep Timer/On Timer is set.
6 indicator
Flashes up in red when the lamp for the light source has burned out.
7 \ 1 indicator
Flashes in green when the light source is preparing to turn on. Lights up in green when the TV is switched on.
Lights up in red when the TV is in standby mode. When the lamp door or the lamp itself is not securely attached, the
red indicator will continue to flash in intervals of three blinks at a time.
8 Remote control sensor
Point the remote here.
9 1
Switches the TV on or off.
– 3 –
Page 5
KF-E42A10/E50A10
RM-GA004 RM-GA004
Projection Lamp
Your TV uses a projection lamp as its light source. As
with any lamp, it has lifespan and needs to be replaced
when the Lamp indicator flashes or the screen
becomes darker.
Notes
After turning on your TV, it may take a while (1 minute or
less) before the picture appears.
When the projection lamp wears out, the screen goes dark.
Replace the lamp with a new Sony XL-2400 replacement
lamp (not supplied). How to replace the lamp, see page 5.
Warning
The light emitted from the lamp is quite bright when your TV
is in use. To avoid eye discomfort or injury, do not look into
the light housing when the power is on.
– 4 –
Page 6
Replacing the lamp
The projection lamp, which illuminates the picture,
has a limited life.
If the screen becomes dark, the color looks unusual, or
the LAMP indicator on the front of the projection TV
flashes, it is time to replace the lamp with a new one
(not supplied).
WARNING
Electric appliances can cause fire or high temperature,
resulting in injury or death. Be sure to follow the instructions
below.
Use a Sony XL-2400 replacement lamp (not supplied) for
replacement. Use of any other lamp may damage the
projection TV.
Do not remove the lamp for any purpose other than
replacement. Doing so may cause injury or fire.
Do not put flammable materials and metal objects inside
the lamp receptacle of the TV after removing the lamp.
Doing so may cause fire or electrical shock. Do not touch
the lamp receptable once the lamp has been removed.
When the lamp eventually burns out, you may hear a
noticeable pop sound. This is normal and it is inherent to
this type of lamp.
In rare instances, the bulb may pop inside the lamp unit,
but the lamp unit is designed to contain all of the broken
glass pieces inside the lamp unit.
KF-E42A10/E50A10
KRM-GA004 RM-GA004
1
Turn off the power on the main unit. Wait
several minutes, then unplug the power
cord.
(The cooling fan will continue to blow for
about two minutes after turning the power
off.)
2
Wait at least 30 minutes after unplugging
the power cord to allow the lamp to cool
down before replacing it. To avoid being
burned, do not touch the lamp receptable
once the lamp has been removed.
3
Take the new lamp out of the box.
Do not touch the glass portion of the new
lamp.
Notes
Do not shake the lamp. Vibration can damage the
lamp or shorten its life.
Avoid touching the front glass of a new lamp or the
glass of the lamp receptacle. This may reduce picture
quality or lamp life.
4
Remove the outside lamp cover.
Disposing of the lamp
This product contains mercury. For disposal or
recycling information, please contact your local
authorities.
Do not leave the used lamp near flammable
materials or within the reach of children.
Do not pour water onto the used lamp or put any
object inside the lamp. Doing so may cause the
lamp to burst.
5
Remove the lamp door.
Turn the knob counterclockwise to OPEN and pull
out the cover.
Lamp door
– 5 –
Page 7
KF-E42A10/E50A10
RM-GA004 RM-GA004
6
Pull out the lamp.
Hook a finger through the loop of the lamp handle
and pull the handle upwards. Then pull the lamp
straight out.
Notes
The lamp is very hot immediately after use. Never
touch the glass portion of the lamp or the surrounding
parts.
After the used lamp has cooled, place it into the empty
box of the replacement lamp. Never put the used lamp
into a plastic bag.
7
Put the new lamp into its place.
Mount the new lamp securely. Failure to do so
may cause a fire or the screen to go dark.
9
Put the outside lamp cover back in its
place.
Notes
Consult your Sony dealer for a Sony XL-2400
replacement lamp.
Take great care when replacing the lamp or plugging
in/unplugging the connecting cords. Rough handling
may cause the TV to fall, damaging the TV, the TV
stand and the floor.
Note
If the lamp is not securely reattached, the self-diagnostic
function may be triggered and the POWER/STANDBY
indicator flashes three times.
8
Reattach the lamp door.
Turn the knob back to CLOSE and secure the
cover.
– 6 –
Page 8
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.
WARNING!!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BECAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PAR TS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED.
KF-E42A10/E50A10
KRM-GA004 RM-GA004
– 7 –
Page 9
KF-E42A10/E50A10
RM-GA004 RM-GA004
TABLE OF CONTENTS
SectionTitlePage
––––––––––––––
1. SELF DIAGNOSIS FUNCTION .....................10
-Incaseofabnormalities, the POWER/STANDBY indicator automatically blinks. It is
possible to predict the abnormality location by the number of blinks. The Instruction
Manual describes blinking of the POWER/STANDBY indicator.
-Ifthe symptom is not reproduced sometimes in case of a malfunction, there is recording of
whether a malfunction was generated or not. Operate the remote command to confirm the
matter on the screen and to predict the location of the abnormality.
2. Diagnosis Items and Prediction of Malfunction Location
-When a malfunction occurs the POWER/STANDBY indicator only blinks for one of the
following diagnosis items. In case of two or more malfunctions, the item which first
occurred blinks. If the malfunctions occurred simultaneously, the item with the lower
blink count blinks first.
-The screen display displays the results regarding all the diagnosis items listed below.
Thedisplay "0" means that no malfunctions occurred.
The POWER/STANDBY indicatorblinking display is released by removing the plug from
the power or leaving for 2 minutes.
4. Self-diagnosis screen displays
-Incases of malfunctions where it is not possible to determine the symptom such as when
the power goes off occasionally or when the screen disappears occasionally, there is a
screen display on whether the malfunction occurred or not in the past (and whether the
detection circuit operated or not) in order to allow confirmation.
<Screen Display Method>
-Quickly press the remote command button in the following order from the standby state.
DISPLAY5-POWER
ChannelVol
Be aware that thisdiffers from
the method of entering the
service mode (Vol +).
SELF CHECK
1:LAMP_ERROR0
2: LAMP_TEMP0
2: TEMP_ERROR0No use
3:LAMP_COVER0
4: FAN_ERROR0
5:LAMP_DRIVER0
6:LOWB_ERROR0
7:AUDIO_PROT0No use
8:D_OVP0No use
10 : ATSC_OVP0No use
-Numeral "1" means a fault was detected one time
-Numeral "0" means that no fault was detected
– 11 –
Page 13
KF-E42A10/E50A10
RM-GA004 RM-GA004
-The results display is not automatically cleared. In case of repairs and after repairs, check
the self-diagnosis screen and be sure to return the results display to "0".
-Ifthe results display is not returned to "0" it will not be possible to judge a new malfunction
after completing repairs.
<Method of Clearing Results Display>
1. Power off (Set to the standby mode)
2.ChannelVol
DISPLAY5-POWER
3. Channel
8ENTER
<Method of Ending Self-Diagnosis Screen>
-When ending the self-diagnosis screen completely, turn the power switch OFF on the
remote commander or the main unit.
5. Self-Diagnosis function operation
1:Lamp_ERRORWhen the lamp is broken.
2:lamp temp overWhen the inside temperature sensed with IC7021, IC7180 and IC603 mounted
on HB board, S2 board and C board respectively exceed the threshold, the lamp
turns off.
3:lamp coverWhen the lamp cover is opened the connector of the lamp is not fixed, the lamp
turns off.
4:FAN When any FAN (FAN1~FAN4) is stopping or harness is not connected correctly,
the lamp turns off.
5:Lamp DriverWhen the ballast is not working with high voltage, the lamp turns off.
6:Low B errorWhen the voltage B_12V is low, TVM(TV u-com) detects it and makes turn off
the lamp.
– 12 –
Page 14
BLOCK DIAGRAM
KF-E42A10/E50A10
KRM-GA004 RM-GA004
AGU board
S2 board
IC7180
Temp.
Sensor
HB board
IC7021
Temp.
Sensor
T2 board
SW
IC8002
TV Micro-computer
IIC-TV
FAN-ERR
IIC-TV
LB-ERR
CN8403
3
1
2
1
38
128
IIC
4
7
10
13
CN8002
+12V
Fan1
Fan2
Fan3
Fan4
B board
IC4100
BE Micro-computer
IIC
T1 board
SW
Lamp
1
3
HV-DET
Lamp Driver
CN8410
CN8410
CN8410
14
15
13
12
CN8003
8
5
CN8003
CN8003
7
7
8
5
7
133
LAMP COVER
134
LAMP-HV-DET
132
LAMP-PROT
– 13 –
Page 15
KF-E42A10/E50A10
RM-GA004 RM-GA004
Reading Lamp and Panel time
Use the following to determine the lamp and panel time of a set.
Screen Display Method
In standby mode, press the buttons on the Remote Commander sequentially, in rapid succession, as shown below:
1. Press Display , Channel 5 , Sound Volume + , Power ON
2. To enter BE-micro service menu, press JUMP 2 times.
3. To display the lamp time, press Channel-4.
The screen displays:
“ Total lamp time is 14 hours”
4. To display the panel time, press Channel-4.
The screen displays:
“ Total panel time is 14 hours”
5. To display the lamp time clear, press Channel-5
7 times and Channel-1.
To reset the lamp time press Channel-3 > MUTING > ENT.
WRITE (Character color is red) is momentarily displayed and the lamp time is reset to “0”.
Exiting Service Mode
To exit the service mode, please turn off the set using the Remote Commander or the power switch.
To HB --- 1,2,3,4,5,6,7,8,9,11,13,14,15,17,19
To HA --- 16,18,20
1
UN_6V
PC_3.3V
+12V
+12V
GND
GND
GND
GND
AGU
GH
CN8002
1 STBY 5V
2 RELAY_VCC
3 FAN 1_POW
4 FAN 1_PROT
5 GND
6 FAN 2_POW
7 FAN 2_PROT
8 GND
9 FAN 3_POW
10 FAN 3_PROT
11 GND
12 FAN 4_POW
13 FAN 4_PROT
14 GND
• Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be anticipated
when ordering these items.
• All variable and adjustable resistors have
characteristic curve B, unless otherwise
noted.
AGU
• RESISTORS
All resistors are in ohms
F : nonflammable
• CAPACITORS
PF : µµF
• There are some cases the reference
number on one board overlaps on the
other board. Therefore, when ordering
parts by the reference number, please
include the board name.
IC80006-704-879-01 IC NJU7223DL1-25
IC80018-759-695-94 IC TAR5S33(TE85R)
IC80026-805-937-01 IC MB91F318APMT-G106-9017E1
IC80038-759-548-56 IC M52055FP
IC80046-704-067-01 IC M24128-BWMN6T(A)
IC80056-801-402-01 IC BD4729GTR
IC80068-759-548-56 IC M52055FP
IC80078-759-278-58 IC NJM4558V-TE2
IC84008-753-232-63 IC CXA2229Q-T6
IC86008-759-646-99 IC NJM4556AV(TE2)
IC86018-759-337-40 IC NJM2904V(TE2)
IC86028-759-337-40 IC NJM2904V(TE2)
IC87006-706-740-01 IC BA00BC0WFP-E2
IC87016-706-740-01 IC BA00BC0WFP-E2
IC87026-706-740-01 IC BA00BC0WFP-E2
IC87036-706-740-01 IC BA00BC0WFP-E2
IC87048-752-072-94 IC CXA1875AM-T4
IC87066-703-225-01 IC S-80928CNMC-G8YT2G
IC88008-752-107-98 IC CXA2188Q-T4
IC88016-706-056-01 IC SN74LVC2GU04DCKR
IC88026-706-903-01 IC AK5357VT-E2
IC88036-706-902-01 IC CXD9835TNDBTR
IC88056-704-819-01 IC CS4335-KSZR
IC88068-759-278-58 IC NJM4558V-TE2
IC88076-704-819-01 IC CS4335-KSZR
R80001-216-841-11 METAL CHIP47K5%1/10W
R80011-216-841-11 METAL CHIP47K5%1/10W
R80051-216-864-11 SHORT CHIP0
R80071-216-864-11 SHORT CHIP0
R80081-216-841-11 METAL CHIP47K5%1/10W
R80091-216-864-11 SHORT CHIP0
R80101-216-809-11 METAL CHIP1005%1/10W
R80111-216-809-11 METAL CHIP1005%1/10W
R80141-216-864-11 SHORT CHIP0
R80151-216-864-11 SHORT CHIP0
R80161-216-864-11 SHORT CHIP0
KF-E42A10/E50A10
KRM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R80171-216-864-11 SHORT CHIP0
R80181-216-864-11 SHORT CHIP0
R80191-216-864-11 SHORT CHIP0
R80201-216-864-11 SHORT CHIP0
R80211-216-864-11 SHORT CHIP0
R80221-216-864-11 SHORT CHIP0
R80231-216-864-11 SHORT CHIP0
R80241-216-864-11 SHORT CHIP0
R80251-216-864-11 SHORT CHIP0
R80261-216-864-11 SHORT CHIP0
R80271-216-805-11 METAL CHIP475%1/10W
R80281-216-809-11 METAL CHIP1005%1/10W
R80291-216-809-11 METAL CHIP1005%1/10W
R80301-216-807-11 METAL CHIP685%1/10W
R80311-216-815-11 METAL CHIP3305%1/10W
R80321-216-841-11 METAL CHIP47K5%1/10W
R80331-216-864-11 SHORT CHIP0
R80341-218-823-11 METAL CHIP1000.5% 1/10W
R80351-216-864-11 SHORT CHIP0
R80361-211-969-11 METAL CHIP100.5% 1/10W
R80371-218-847-11 METAL CHIP1K0.5% 1/10W
R80381-218-847-11 METAL CHIP1K0.5% 1/10W
R80391-218-847-11 METAL CHIP1K0.5% 1/10W
R80401-216-805-11 METAL CHIP475%1/10W
R80411-216-864-11 SHORT CHIP0
R80421-216-864-11 SHORT CHIP0
R80431-216-864-11 SHORT CHIP0
R80441-218-847-11 METAL CHIP1K0.5% 1/10W
R80451-216-809-11 METAL CHIP1005%1/10W
R80461-216-809-11 METAL CHIP1005%1/10W
R80471-216-864-11 SHORT CHIP0
R80481-218-839-11 METAL CHIP4700.5% 1/10W
R80491-216-833-11 METAL CHIP10K5%1/10W
R80501-216-864-11 SHORT CHIP0
R80511-216-809-11 METAL CHIP1005%1/10W
R80521-218-855-11 METAL CHIP2.2K0.5% 1/10W
R80531-218-847-11 METAL CHIP1K0.5% 1/10W
R80541-218-847-11 METAL CHIP1K0.5% 1/10W
R80551-218-839-11 METAL CHIP4700.5% 1/10W
R80561-218-865-11 METAL CHIP5.6K0.5% 1/10W
R80571-216-851-11 METAL CHIP330K5%1/10W
R80581-218-871-11 METAL CHIP10K0.5% 1/10W
R80591-218-871-11 METAL CHIP10K0.5% 1/10W
R80601-219-570-11 METAL CHIP10M5%1/10W
R80611-218-895-11 METAL CHIP100K0.5% 1/10W
R80621-216-841-11 METAL CHIP47K5%1/10W
R80631-218-887-11 METAL CHIP47K0.5% 1/10W
R80641-216-809-11 METAL CHIP1005%1/10W
R80651-218-895-11 METAL CHIP100K0.5% 1/10W
R80661-218-895-11 METAL CHIP100K0.5% 1/10W
R80671-218-895-11 METAL CHIP100K0.5% 1/10W
R80681-218-871-11 METAL CHIP10K0.5% 1/10W
R80691-218-871-11 METAL CHIP10K0.5% 1/10W
R80701-216-821-11 METAL CHIP1K5%1/10W
R80711-218-871-11 METAL CHIP10K0.5% 1/10W
R80721-218-887-11 METAL CHIP47K0.5% 1/10W
R80731-218-883-11 METAL CHIP33K0.5% 1/10W
R80741-216-853-11 METAL CHIP470K5%1/10W
R80751-216-821-11 METAL CHIP1K5%1/10W
R80761-216-809-11 METAL CHIP1005%1/10W
R80771-216-805-11 METAL CHIP475%1/10W
R80781-216-805-11 METAL CHIP475%1/10W
R80791-216-805-11 METAL CHIP475%1/10W
– 65 –
Page 67
KF-E42A10/E50A10
RM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R80811-216-805-11 METAL CHIP475%1/10W
R80821-216-821-11 METAL CHIP1K5%1/10W
R80831-216-805-11 METAL CHIP475%1/10W
R80841-216-841-11 METAL CHIP47K5%1/10W
R80851-216-833-11 METAL CHIP10K5%1/10W
R80871-216-853-11 METAL CHIP470K5%1/10W
R80881-216-809-11 METAL CHIP1005%1/10W
R80891-216-821-11 METAL CHIP1K5%1/10W
R80901-216-821-11 METAL CHIP1K5%1/10W
R80911-216-809-11 METAL CHIP1005%1/10W
R80921-216-809-11 METAL CHIP1005%1/10W
R80931-216-833-11 METAL CHIP10K5%1/10W
R80951-216-821-11 METAL CHIP1K5%1/10W
R80971-216-833-11 METAL CHIP10K5%1/10W
R80981-216-821-11 METAL CHIP1K5%1/10W
R80991-216-821-11 METAL CHIP1K5%1/10W
R81001-216-833-11 METAL CHIP10K5%1/10W
R81031-216-829-11 METAL CHIP4.7K5%1/10W
R81041-216-864-11 SHORT CHIP0
R81051-216-833-11 METAL CHIP10K5%1/10W
R81081-216-833-11 METAL CHIP10K5%1/10W
R81091-216-841-11 METAL CHIP47K5%1/10W
R81101-216-821-11 METAL CHIP1K5%1/10W
R81111-216-821-11 METAL CHIP1K5%1/10W
R81141-216-833-11 METAL CHIP10K5%1/10W
R81171-216-829-11 METAL CHIP4.7K5%1/10W
R81181-216-809-11 METAL CHIP1005%1/10W
R81191-216-809-11 METAL CHIP1005%1/10W
R81201-216-805-11 METAL CHIP475%1/10W
R81211-216-864-11 SHORT CHIP0
R81221-216-864-11 SHORT CHIP0
R81231-216-805-11 METAL CHIP475%1/10W
R81241-216-864-11 SHORT CHIP0
R81251-216-833-11 METAL CHIP10K5%1/10W
R81261-216-809-11 METAL CHIP1005%1/10W
R81271-216-809-11 METAL CHIP1005%1/10W
R81281-216-864-11 SHORT CHIP0
R81291-216-833-11 METAL CHIP10K5%1/10W
R81301-216-809-11 METAL CHIP1005%1/10W
R81311-216-809-11 METAL CHIP1005%1/10W
R81321-216-809-11 METAL CHIP1005%1/10W
R81331-216-809-11 METAL CHIP1005%1/10W
R81341-216-809-11 METAL CHIP1005%1/10W
R81351-216-809-11 METAL CHIP1005%1/10W
R81361-216-833-11 METAL CHIP10K5%1/10W
R81381-216-833-11 METAL CHIP10K5%1/10W
R81391-216-864-11 SHORT CHIP0
R81401-216-864-11 SHORT CHIP0
R81411-216-864-11 SHORT CHIP0
R81421-216-821-11 METAL CHIP1K5%1/10W
R81431-216-805-11 METAL CHIP475%1/10W
R81441-216-821-11 METAL CHIP1K5%1/10W
R81451-216-821-11 METAL CHIP1K5%1/10W
R81461-216-864-11 SHORT CHIP0
R81471-211-990-11 METAL CHIP750.5% 1/10W
R81481-216-853-11 METAL CHIP470K5%1/10W
R81491-216-853-11 METAL CHIP470K5%1/10W
R81501-216-833-11 METAL CHIP10K5%1/10W
R81511-216-853-11 METAL CHIP470K5%1/10W
R81521-216-821-11 METAL CHIP1K5%1/10W
R81531-216-809-11 METAL CHIP1005%1/10W
R81541-216-821-11 METAL CHIP1K5%1/10W
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R81551-216-821-11 METAL CHIP1K5%1/10W
R81561-216-808-11 METAL CHIP825%1/10W
R81571-216-825-11 METAL CHIP2.2K5%1/10W
R81581-216-829-11 METAL CHIP4.7K5%1/10W
R81591-216-833-11 METAL CHIP10K5%1/10W
R81601-216-809-11 METAL CHIP1005%1/10W
R81611-216-841-11 METAL CHIP47K5%1/10W
R81621-216-864-11 SHORT CHIP0
R81631-216-864-11 SHORT CHIP0
R81641-216-864-11 SHORT CHIP0
R81651-216-864-11 SHORT CHIP0
R81661-216-824-11 METAL CHIP1.8K5%1/10W
R81671-216-809-11 METAL CHIP1005%1/10W
R81681-216-845-11 METAL CHIP100K5%1/10W
R81691-216-833-11 METAL CHIP10K5%1/10W
R81701-216-809-11 METAL CHIP1005%1/10W
R81711-216-824-11 METAL CHIP1.8K5%1/10W
R81721-216-818-11 METAL CHIP5605%1/10W
R81731-216-864-11 SHORT CHIP0
R81741-216-809-11 METAL CHIP1005%1/10W
R81751-216-809-11 METAL CHIP1005%1/10W
R81761-216-864-11 SHORT CHIP0
R81781-216-864-11 SHORT CHIP0
R81791-216-821-11 METAL CHIP1K5%1/10W
R81811-216-827-11 METAL CHIP3.3K5%1/10W
R81821-216-829-11 METAL CHIP4.7K5%1/10W
R81831-216-829-11 METAL CHIP4.7K5%1/10W
R81841-216-827-11 METAL CHIP3.3K5%1/10W
R81851-216-834-11 METAL CHIP12K5%1/10W
R81861-216-825-11 METAL CHIP2.2K5%1/10W
R81871-216-833-11 METAL CHIP10K5%1/10W
R81881-216-825-11 METAL CHIP2.2K5%1/10W
R81891-216-845-11 METAL CHIP100K5%1/10W
R81901-216-833-11 METAL CHIP10K5%1/10W
R81911-216-845-11 METAL CHIP100K5%1/10W
R81951-216-864-11 SHORT CHIP0
R81961-216-809-11 METAL CHIP1005%1/10W
R81971-216-864-11 SHORT CHIP0
R81981-216-809-11 METAL CHIP1005%1/10W
R81991-216-826-11 METAL CHIP2.7K5%1/10W
R82001-216-833-11 METAL CHIP10K5%1/10W
R82011-216-833-11 METAL CHIP10K5%1/10W
R82021-216-829-11 METAL CHIP4.7K5%1/10W
R82031-216-833-11 METAL CHIP10K5%1/10W
R82041-216-864-11 SHORT CHIP0
R82051-216-864-11 SHORT CHIP0
R82061-216-814-11 METAL CHIP2705%1/10W
R82071-216-833-11 METAL CHIP10K5%1/10W
R82081-216-833-11 METAL CHIP10K5%1/10W
R82091-216-833-11 METAL CHIP10K5%1/10W
R82101-216-833-11 METAL CHIP10K5%1/10W
R82111-216-833-11 METAL CHIP10K5%1/10W
R82121-216-833-11 METAL CHIP10K5%1/10W
R82131-216-841-11 METAL CHIP47K5%1/10W
R82141-216-841-11 METAL CHIP47K5%1/10W
R82151-216-864-11 SHORT CHIP0
R82161-216-864-11 SHORT CHIP0
R82171-216-833-11 METAL CHIP10K5%1/10W
R82181-216-864-11 SHORT CHIP0
R82191-216-864-11 SHORT CHIP0
R82201-216-837-11 METAL CHIP22K5%1/10W
R82221-216-864-11 SHORT CHIP0
R82231-216-833-11 METAL CHIP10K5%1/10W
– 66 –
Page 68
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R82241-216-837-11 METAL CHIP22K5%1/10W
R82261-216-833-11 METAL CHIP10K5%1/10W
R82271-216-864-11 SHORT CHIP0
R82281-216-833-11 METAL CHIP10K5%1/10W
R82291-216-828-11 METAL CHIP3.9K5%1/10W
R82301-216-821-11 METAL CHIP1K5%1/10W
R82311-216-853-11 METAL CHIP470K5%1/10W
R82321-216-864-11 SHORT CHIP0
R82331-216-864-11 SHORT CHIP0
R82341-216-829-11 METAL CHIP4.7K5%1/10W
R82351-216-809-11 METAL CHIP1005%1/10W
R82361-216-809-11 METAL CHIP1005%1/10W
R82371-216-829-11 METAL CHIP4.7K5%1/10W
R82391-216-821-11 METAL CHIP1K5%1/10W
R82401-216-829-11 METAL CHIP4.7K5%1/10W
R82411-216-809-11 METAL CHIP1005%1/10W
R82421-216-833-11 METAL CHIP10K5%1/10W
R82431-216-809-11 METAL CHIP1005%1/10W
R82441-216-833-11 METAL CHIP10K5%1/10W
R82451-216-857-11 METAL CHIP1M5%1/10W
R82461-216-857-11 METAL CHIP1M5%1/10W
R82471-216-821-11 METAL CHIP1K5%1/10W
R82481-216-829-11 METAL CHIP4.7K5%1/10W
R82491-216-809-11 METAL CHIP1005%1/10W
R82501-216-805-11 METAL CHIP475%1/10W
R82511-216-805-11 METAL CHIP475%1/10W
R82521-216-805-11 METAL CHIP475%1/10W
R82531-216-829-11 METAL CHIP4.7K5%1/10W
R82541-216-829-11 METAL CHIP4.7K5%1/10W
R82551-216-864-11 SHORT CHIP0
R82581-216-857-11 METAL CHIP1M5%1/10W
R82621-216-805-11 METAL CHIP475%1/10W
R82631-216-805-11 METAL CHIP475%1/10W
R82651-216-805-11 METAL CHIP475%1/10W
R82661-216-864-11 SHORT CHIP0
R82671-216-861-11 METAL CHIP2.2M5%1/10W
R82681-216-817-11 METAL CHIP4705%1/10W
R82691-216-809-11 METAL CHIP1005%1/10W
R82731-216-813-11 METAL CHIP2205%1/10W
R82741-218-849-11 METAL CHIP1.2K0.5% 1/10W
R82761-216-833-11 METAL CHIP10K5%1/10W
R82771-216-833-11 METAL CHIP10K5%1/10W
R82781-216-825-11 METAL CHIP2.2K5%1/10W
R82791-218-849-11 METAL CHIP1.2K0.5% 1/10W
R82801-216-864-11 SHORT CHIP0
R82811-216-864-11 SHORT CHIP0
R82831-216-809-11 METAL CHIP1005%1/10W
R82841-218-849-11 METAL CHIP1.2K0.5% 1/10W
R82851-216-864-11 SHORT CHIP0
R82871-216-864-11 SHORT CHIP0
R82891-216-821-11 METAL CHIP1K5%1/10W
R82901-216-821-11 METAL CHIP1K5%1/10W
R82931-216-821-11 METAL CHIP1K5%1/10W
R82941-216-814-11 METAL CHIP2705%1/10W
R82951-216-840-11 METAL CHIP39K5%1/10W
R82961-216-825-11 METAL CHIP2.2K5%1/10W
R82971-216-825-11 METAL CHIP2.2K5%1/10W
R82981-216-864-11 SHORT CHIP0
R83001-216-864-11 SHORT CHIP0
R83011-216-829-11 METAL CHIP4.7K5%1/10W
R83021-216-809-11 METAL CHIP1005%1/10W
R83051-216-864-11 SHORT CHIP0
KF-E42A10/E50A10
KRM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R83061-216-829-11 METAL CHIP4.7K5%1/10W
R83081-216-815-11 METAL CHIP3305%1/10W
R83091-216-809-11 METAL CHIP1005%1/10W
R83191-216-833-11 METAL CHIP10K5%1/10W
R83201-216-833-11 METAL CHIP10K5%1/10W
R83281-216-833-11 METAL CHIP10K5%1/10W
R83301-216-864-11 SHORT CHIP0
R83311-216-864-11 SHORT CHIP0
R83331-216-833-11 METAL CHIP10K5%1/10W
R83341-216-845-11 METAL CHIP100K5%1/10W
R83361-216-845-11 METAL CHIP100K5%1/10W
R83401-216-864-11 SHORT CHIP0
R83411-216-864-11 SHORT CHIP0
R83421-216-864-11 SHORT CHIP0
R83431-216-864-11 SHORT CHIP0
R83441-216-864-11 SHORT CHIP0
R83451-216-864-11 SHORT CHIP0
R83461-216-864-11 SHORT CHIP0
R83471-216-864-11 SHORT CHIP0
R83481-216-864-11 SHORT CHIP0
R83491-216-864-11 SHORT CHIP0
R83511-216-805-11 METAL CHIP475%1/10W
R83561-216-813-11 METAL CHIP2205%1/10W
R83581-216-864-11 SHORT CHIP0
R83591-216-833-11 METAL CHIP10K5%1/10W
R83601-216-864-11 SHORT CHIP0
R83611-216-809-11 METAL CHIP1005%1/10W
R83621-216-809-11 METAL CHIP1005%1/10W
R83631-216-864-11 SHORT CHIP0
R83641-216-864-11 SHORT CHIP0
R83671-216-833-11 METAL CHIP10K5%1/10W
R83691-216-805-11 METAL CHIP475%1/10W
R83701-216-864-11 SHORT CHIP0
R83711-216-821-11 METAL CHIP1K5%1/10W
R83721-216-837-11 METAL CHIP22K5%1/10W
R83741-216-817-11 METAL CHIP4705%1/10W
R83751-216-839-11 METAL CHIP33K5%1/10W
R83761-216-821-11 METAL CHIP1K5%1/10W
R83771-216-864-11 SHORT CHIP0
R83801-216-835-11 METAL CHIP15K5%1/10W
R83811-216-801-11 METAL CHIP225%1/10W
R83821-216-864-11 SHORT CHIP0
R83841-216-833-11 METAL CHIP10K5%1/10W
R83851-216-813-11 METAL CHIP2205%1/10W
R83861-218-851-11 METAL CHIP1.5K0.5% 1/10W
R83881-216-864-11 SHORT CHIP0
R83901-216-833-11 METAL CHIP10K5%1/10W
R83921-216-833-11 METAL CHIP10K5%1/10W
R83931-216-864-11 SHORT CHIP0
R83941-216-864-11 SHORT CHIP0
R83961-216-833-11 METAL CHIP10K5%1/10W
R83971-216-833-11 METAL CHIP10K5%1/10W
R83981-216-833-11 METAL CHIP10K5%1/10W
R84001-216-853-11 METAL CHIP470K5%1/10W
R84011-216-853-11 METAL CHIP470K5%1/10W
R84021-218-831-11 METAL CHIP2200.5% 1/10W
R84031-218-831-11 METAL CHIP2200.5% 1/10W
R84041-218-831-11 METAL CHIP2200.5% 1/10W
R84051-216-853-11 METAL CHIP470K5%1/10W
R84061-216-853-11 METAL CHIP470K5%1/10W
R84071-218-831-11 METAL CHIP2200.5% 1/10W
R84081-218-831-11 METAL CHIP2200.5% 1/10W
R84091-216-853-11 METAL CHIP470K5%1/10W
– 67 –
Page 69
KF-E42A10/E50A10
RM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R84101-218-831-11 METAL CHIP2200.5% 1/10W
R84111-218-831-11 METAL CHIP2200.5% 1/10W
R84121-218-831-11 METAL CHIP2200.5% 1/10W
R84131-218-831-11 METAL CHIP2200.5% 1/10W
R84141-218-831-11 METAL CHIP2200.5% 1/10W
R84151-218-831-11 METAL CHIP2200.5% 1/10W
R84161-218-831-11 METAL CHIP2200.5% 1/10W
R84171-218-831-11 METAL CHIP2200.5% 1/10W
R84181-218-831-11 METAL CHIP2200.5% 1/10W
R84201-216-864-11 SHORT CHIP0
R84221-216-815-11 METAL CHIP3305%1/10W
R84231-216-797-11 METAL CHIP105%1/10W
R84241-216-815-11 METAL CHIP3305%1/10W
R84251-216-809-11 METAL CHIP1005%1/10W
R84261-216-797-11 METAL CHIP105%1/10W
R84271-216-809-11 METAL CHIP1005%1/10W
R84281-218-831-11 METAL CHIP2200.5% 1/10W
R84291-218-831-11 METAL CHIP2200.5% 1/10W
R84301-216-864-11 SHORT CHIP0
R84321-216-864-11 SHORT CHIP0
R84331-216-864-11 SHORT CHIP0
R84341-216-864-11 SHORT CHIP0
R84351-216-864-11 SHORT CHIP0
R84361-216-864-11 SHORT CHIP0
R84371-218-831-11 METAL CHIP2200.5% 1/10W
R84381-218-831-11 METAL CHIP2200.5% 1/10W
R84391-218-831-11 METAL CHIP2200.5% 1/10W
R84401-218-831-11 METAL CHIP2200.5% 1/10W
R84411-218-831-11 METAL CHIP2200.5% 1/10W
R84421-218-831-11 METAL CHIP2200.5% 1/10W
R84431-216-853-11 METAL CHIP470K5%1/10W
R84441-216-807-11 METAL CHIP685%1/10W
R84451-216-805-11 METAL CHIP475%1/10W
R84461-216-807-11 METAL CHIP685%1/10W
R84471-216-815-11 METAL CHIP3305%1/10W
R84481-216-815-11 METAL CHIP3305%1/10W
R84501-216-809-11 METAL CHIP1005%1/10W
R84511-216-809-11 METAL CHIP1005%1/10W
R84531-216-825-11 METAL CHIP2.2K5%1/10W
R84541-216-815-11 METAL CHIP3305%1/10W
R84551-216-864-11 SHORT CHIP0
R84571-216-833-11 METAL CHIP10K5%1/10W
R84581-216-864-11 SHORT CHIP0
R84611-216-809-11 METAL CHIP1005%1/10W
R84621-216-829-11 METAL CHIP4.7K5%1/10W
R84631-216-809-11 METAL CHIP1005%1/10W
R84641-216-807-11 METAL CHIP685%1/10W
R84651-216-807-11 METAL CHIP685%1/10W
R84661-216-853-11 METAL CHIP470K5%1/10W
R84671-216-815-11 METAL CHIP3305%1/10W
R84681-216-815-11 METAL CHIP3305%1/10W
R84691-216-815-11 METAL CHIP3305%1/10W
R84701-218-855-11 METAL CHIP2.2K0.5% 1/10W
R84711-216-864-11 SHORT CHIP0
R84731-216-821-11 METAL CHIP1K5%1/10W
R84741-216-809-11 METAL CHIP1005%1/10W
R84751-216-809-11 METAL CHIP1005%1/10W
R84761-216-829-11 METAL CHIP4.7K5%1/10W
R84771-216-809-11 METAL CHIP1005%1/10W
R84781-216-821-11 METAL CHIP1K5%1/10W
R84791-216-857-11 METAL CHIP1M5%1/10W
R84801-216-809-11 METAL CHIP1005%1/10W
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R84811-216-821-11 METAL CHIP1K5%1/10W
R84821-216-821-11 METAL CHIP1K5%1/10W
R84841-216-801-11 METAL CHIP225%1/10W
R84851-216-801-11 METAL CHIP225%1/10W
R84861-216-809-11 METAL CHIP1005%1/10W
R84871-216-805-11 METAL CHIP475%1/10W
R84891-216-809-11 METAL CHIP1005%1/10W
R84901-216-857-11 METAL CHIP1M5%1/10W
R84911-216-809-11 METAL CHIP1005%1/10W
R84921-216-821-11 METAL CHIP1K5%1/10W
R84931-216-809-11 METAL CHIP1005%1/10W
R84951-216-809-11 METAL CHIP1005%1/10W
R84961-218-871-11 METAL CHIP10K0.5% 1/10W
R84971-216-809-11 METAL CHIP1005%1/10W
R84981-216-809-11 METAL CHIP1005%1/10W
R84991-216-809-11 METAL CHIP1005%1/10W
R85001-216-809-11 METAL CHIP1005%1/10W
R85041-216-809-11 METAL CHIP1005%1/10W
R85051-216-809-11 METAL CHIP1005%1/10W
R85061-216-809-11 METAL CHIP1005%1/10W
R85091-216-809-11 METAL CHIP1005%1/10W
R85101-216-809-11 METAL CHIP1005%1/10W
R85111-216-809-11 METAL CHIP1005%1/10W
R85131-216-861-11 METAL CHIP2.2M5%1/10W
R85141-216-861-11 METAL CHIP2.2M5%1/10W
R85151-216-809-11 METAL CHIP1005%1/10W
R85161-216-809-11 METAL CHIP1005%1/10W
R85171-216-829-11 METAL CHIP4.7K5%1/10W
R85181-216-829-11 METAL CHIP4.7K5%1/10W
R85191-216-821-11 METAL CHIP1K5%1/10W
R85201-216-809-11 METAL CHIP1005%1/10W
R85211-216-821-11 METAL CHIP1K5%1/10W
R85221-216-809-11 METAL CHIP1005%1/10W
R85261-216-864-11 SHORT CHIP0
R85271-216-864-11 SHORT CHIP0
R85291-216-864-11 SHORT CHIP0
R85301-211-990-11 METAL CHIP750.5% 1/10W
R85311-211-990-11 METAL CHIP750.5% 1/10W
R85321-211-990-11 METAL CHIP750.5% 1/10W
R85371-216-864-11 SHORT CHIP0
R85381-216-864-11 SHORT CHIP0
R85391-216-864-11 SHORT CHIP0
R85401-216-864-11 SHORT CHIP0
R85411-216-864-11 SHORT CHIP0
R85421-216-857-11 METAL CHIP1M5%1/10W
R85431-216-837-11 METAL CHIP22K5%1/10W
R85441-216-837-11 METAL CHIP22K5%1/10W
R85451-216-829-11 METAL CHIP4.7K5%1/10W
R85461-216-864-11 SHORT CHIP0
R85481-216-864-11 SHORT CHIP0
R85491-216-833-11 METAL CHIP10K5%1/10W
R85501-216-809-11 METAL CHIP1005%1/10W
R85511-216-815-11 METAL CHIP3305%1/10W
R85521-216-853-11 METAL CHIP470K5%1/10W
R85531-216-833-11 METAL CHIP10K5%1/10W
R85541-216-861-11 METAL CHIP2.2M5%1/10W
R85551-216-864-11 SHORT CHIP0
R85561-218-831-11 METAL CHIP2200.5% 1/10W
R85571-218-831-11 METAL CHIP2200.5% 1/10W
R85581-218-831-11 METAL CHIP2200.5% 1/10W
R85591-218-831-11 METAL CHIP2200.5% 1/10W
R85601-218-831-11 METAL CHIP2200.5% 1/10W
R85611-218-831-11 METAL CHIP2200.5% 1/10W
– 68 –
Page 70
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R85621-218-831-11 METAL CHIP2200.5% 1/10W
R85631-218-831-11 METAL CHIP2200.5% 1/10W
R85641-218-831-11 METAL CHIP2200.5% 1/10W
R85651-218-831-11 METAL CHIP2200.5% 1/10W
R85661-218-831-11 METAL CHIP2200.5% 1/10W
R85671-218-831-11 METAL CHIP2200.5% 1/10W
R85681-218-831-11 METAL CHIP2200.5% 1/10W
R85691-218-831-11 METAL CHIP2200.5% 1/10W
R85701-218-831-11 METAL CHIP2200.5% 1/10W
R85711-218-831-11 METAL CHIP2200.5% 1/10W
R85721-218-831-11 METAL CHIP2200.5% 1/10W
R85751-216-821-11 METAL CHIP1K5%1/10W
R85761-216-864-11 SHORT CHIP0
R85771-216-864-11 SHORT CHIP0
R85841-218-887-11 METAL CHIP47K0.5% 1/10W
R87001-216-845-11 METAL CHIP100K5%1/10W
R87011-216-833-11 METAL CHIP10K5%1/10W
R87031-216-833-11 METAL CHIP10K5%1/10W
R87051-216-864-11 SHORT CHIP0
R87061-216-824-11 METAL CHIP1.8K5%1/10W
R87071-216-833-11 METAL CHIP10K5%1/10W
R87091-216-833-11 METAL CHIP10K5%1/10W
R87101-216-833-11 METAL CHIP10K5%1/10W
R87121-216-833-11 METAL CHIP10K5%1/10W
R87181-218-887-11 METAL CHIP47K0.5% 1/10W
R87191-218-903-11 METAL CHIP220K0.5% 1/10W
R87201-218-887-11 METAL CHIP47K0.5% 1/10W
R87211-218-903-11 METAL CHIP220K0.5% 1/10W
R87221-218-887-11 METAL CHIP47K0.5% 1/10W
R87231-218-903-11 METAL CHIP220K0.5% 1/10W
R87241-218-887-11 METAL CHIP47K0.5% 1/10W
R87251-218-903-11 METAL CHIP220K0.5% 1/10W
R87261-218-897-11 METAL CHIP120K0.5% 1/10W
R87271-216-833-11 METAL CHIP10K5%1/10W
R87281-216-833-11 METAL CHIP10K5%1/10W
R87291-216-864-11 SHORT CHIP0
R87301-216-864-11 SHORT CHIP0
R87311-216-864-11 SHORT CHIP0
R87321-216-801-11 METAL CHIP225%1/10W
R87331-216-801-11 METAL CHIP225%1/10W
R87341-218-897-11 METAL CHIP120K0.5% 1/10W
R87351-218-897-11 METAL CHIP120K0.5% 1/10W
R87361-218-897-11 METAL CHIP120K0.5% 1/10W
R87371-216-821-11 METAL CHIP1K5%1/10W
R87381-216-821-11 METAL CHIP1K5%1/10W
R87391-216-821-11 METAL CHIP1K5%1/10W
R87401-216-821-11 METAL CHIP1K5%1/10W
R87411-216-845-11 METAL CHIP100K5%1/10W
R87421-216-845-11 METAL CHIP100K5%1/10W
R87431-216-845-11 METAL CHIP100K5%1/10W
R87451-216-829-11 METAL CHIP4.7K5%1/10W
R87461-216-845-11 METAL CHIP100K5%1/10W
R87471-216-833-11 METAL CHIP10K5%1/10W
R87481-216-833-11 METAL CHIP10K5%1/10W
R87491-216-833-11 METAL CHIP10K5%1/10W
R87501-216-833-11 METAL CHIP10K5%1/10W
R87511-216-833-11 METAL CHIP10K5%1/10W
R87521-216-833-11 METAL CHIP10K5%1/10W
R87531-216-845-11 METAL CHIP100K5%1/10W
R87541-216-845-11 METAL CHIP100K5%1/10W
R87551-216-845-11 METAL CHIP100K5%1/10W
R87561-216-845-11 METAL CHIP100K5%1/10W
R87571-216-797-11 METAL CHIP105%1/10W
KF-E42A10/E50A10
KRM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R87581-216-797-11 METAL CHIP105%1/10W
R87591-216-797-11 METAL CHIP105%1/10W
R87601-216-797-11 METAL CHIP105%1/10W
R87611-216-864-11 SHORT CHIP0
R87631-216-864-11 SHORT CHIP0
R87651-216-864-11 SHORT CHIP0
R87801-216-833-11 METAL CHIP10K5%1/10W
R87811-216-833-11 METAL CHIP10K5%1/10W
R87821-218-897-11 METAL CHIP120K0.5% 1/10W
R87831-216-821-11 METAL CHIP1K5%1/10W
R87841-216-845-11 METAL CHIP100K5%1/10W
R87851-216-845-11 METAL CHIP100K5%1/10W
R87861-216-797-11 METAL CHIP105%1/10W
R87881-218-887-11 METAL CHIP47K0.5% 1/10W
R87891-218-903-11 METAL CHIP220K0.5% 1/10W
R87901-216-829-11 METAL CHIP4.7K5%1/10W
R87941-216-853-11 METAL CHIP470K5%1/10W
R87951-216-853-11 METAL CHIP470K5%1/10W
R87961-216-809-11 METAL CHIP1005%1/10W
R87971-216-809-11 METAL CHIP1005%1/10W
R87981-216-809-11 METAL CHIP1005%1/10W
R87991-216-809-11 METAL CHIP1005%1/10W
R88001-216-853-11 METAL CHIP470K5%1/10W
R88011-216-853-11 METAL CHIP470K5%1/10W
R88021-216-829-11 METAL CHIP4.7K5%1/10W
R88031-216-829-11 METAL CHIP4.7K5%1/10W
R88041-216-829-11 METAL CHIP4.7K5%1/10W
R88051-216-829-11 METAL CHIP4.7K5%1/10W
R88061-216-829-11 METAL CHIP4.7K5%1/10W
R88071-216-829-11 METAL CHIP4.7K5%1/10W
R88081-216-805-11 METAL CHIP475%1/10W
R88091-216-817-11 METAL CHIP4705%1/10W
R88101-216-857-11 METAL CHIP1M5%1/10W
R88121-216-834-11 METAL CHIP12K5%1/10W
R88131-216-834-11 METAL CHIP12K5%1/10W
R88141-216-829-11 METAL CHIP4.7K5%1/10W
R88151-216-864-11 SHORT CHIP0
R88161-216-829-11 METAL CHIP4.7K5%1/10W
R88171-216-833-11 METAL CHIP10K5%1/10W
R88181-216-833-11 METAL CHIP10K5%1/10W
R88191-216-829-11 METAL CHIP4.7K5%1/10W
R88201-216-829-11 METAL CHIP4.7K5%1/10W
R88221-216-829-11 METAL CHIP4.7K5%1/10W
R88231-216-805-11 METAL CHIP475%1/10W
R88241-216-829-11 METAL CHIP4.7K5%1/10W
R88251-216-813-11 METAL CHIP2205%1/10W
R88261-216-813-11 METAL CHIP2205%1/10W
R88271-216-805-11 METAL CHIP475%1/10W
R88281-216-805-11 METAL CHIP475%1/10W
R88291-216-805-11 METAL CHIP475%1/10W
R88301-216-805-11 METAL CHIP475%1/10W
R88321-216-805-11 METAL CHIP475%1/10W
R88331-216-805-11 METAL CHIP475%1/10W
R88341-216-805-11 METAL CHIP475%1/10W
R88351-216-809-11 METAL CHIP1005%1/10W
R88361-216-813-11 METAL CHIP2205%1/10W
R88381-216-805-11 METAL CHIP475%1/10W
R88391-216-805-11 METAL CHIP475%1/10W
R88411-216-805-11 METAL CHIP475%1/10W
R88421-216-813-11 METAL CHIP2205%1/10W
R88441-216-805-11 METAL CHIP475%1/10W
R88451-216-805-11 METAL CHIP475%1/10W
R88461-216-834-11 METAL CHIP12K5%1/10W
– 69 –
Page 71
KF-E42A10/E50A10
RM-GA004 RM-GA004
AGU
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R88471-216-845-11 METAL CHIP100K5%1/10W
R88481-216-833-11 METAL CHIP10K5%1/10W
R88491-216-825-11 METAL CHIP2.2K5%1/10W
R88501-216-825-11 METAL CHIP2.2K5%1/10W
R88511-216-825-11 METAL CHIP2.2K5%1/10W
R88531-216-825-11 METAL CHIP2.2K5%1/10W
R88541-216-845-11 METAL CHIP100K5%1/10W
R88561-216-825-11 METAL CHIP2.2K5%1/10W
R88601-216-833-11 METAL CHIP10K5%1/10W
R88611-216-805-11 METAL CHIP475%1/10W
R88621-216-833-11 METAL CHIP10K5%1/10W
R88631-216-825-11 METAL CHIP2.2K5%1/10W
R88641-216-825-11 METAL CHIP2.2K5%1/10W
R88651-216-833-11 METAL CHIP10K5%1/10W
R88721-216-805-11 METAL CHIP475%1/10W
R88731-216-805-11 METAL CHIP475%1/10W
R88741-216-821-11 METAL CHIP1K5%1/10W
R88801-216-809-11 METAL CHIP1005%1/10W
R88811-216-809-11 METAL CHIP1005%1/10W
R88821-216-805-11 METAL CHIP475%1/10W
R88831-216-828-11 METAL CHIP3.9K5%1/10W
R88841-216-828-11 METAL CHIP3.9K5%1/10W
R88851-216-864-11 SHORT CHIP0
R88861-216-853-11 METAL CHIP470K5%1/10W
R88871-216-864-11 SHORT CHIP0
R88881-216-853-11 METAL CHIP470K5%1/10W
R88891-216-864-11 SHORT CHIP0
R88901-216-864-11 SHORT CHIP0
R88931-216-864-11 SHORT CHIP0
R88951-216-805-11 METAL CHIP475%1/10W
R88961-216-805-11 METAL CHIP475%1/10W
R88981-216-864-11 SHORT CHIP0
R88991-218-823-11 METAL CHIP1000.5% 1/10W
R89001-216-864-11 SHORT CHIP0
R89011-216-864-11 SHORT CHIP0
R89021-216-864-11 SHORT CHIP0
R89031-216-864-11 SHORT CHIP0
R89041-216-864-11 SHORT CHIP0
R89051-218-823-11 METAL CHIP1000.5% 1/10W
R89061-216-825-11 METAL CHIP2.2K5%1/10W
AS
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R89431-216-805-11 METAL CHIP475%1/10W
R89441-216-805-11 METAL CHIP475%1/10W
R89451-216-809-11 METAL CHIP1005%1/10W
R89461-216-809-11 METAL CHIP1005%1/10W
R89471-216-833-11 METAL CHIP10K5%1/10W
R89481-216-833-11 METAL CHIP10K5%1/10W
R89491-216-841-11 METAL CHIP47K5%1/10W
R89501-216-833-11 METAL CHIP10K5%1/10W
R89511-216-821-11 METAL CHIP1K5%1/10W
R89521-216-821-11 METAL CHIP1K5%1/10W
R89531-216-809-11 METAL CHIP1005%1/10W
R89541-216-809-11 METAL CHIP1005%1/10W
R89711-216-864-11 SHORT CHIP0
R89721-216-864-11 SHORT CHIP0
R89741-216-829-11 METAL CHIP4.7K5%1/10W
R89751-216-841-11 METAL CHIP47K5%1/10W
R89761-216-845-11 METAL CHIP100K5%1/10W
R89771-216-845-11 METAL CHIP100K5%1/10W
R89781-216-829-11 METAL CHIP4.7K5%1/10W
R89791-216-829-11 METAL CHIP4.7K5%1/10W
R89801-216-833-11 METAL CHIP10K5%1/10W
R89811-216-833-11 METAL CHIP10K5%1/10W
R89821-216-833-11 METAL CHIP10K5%1/10W
R89831-216-833-11 METAL CHIP10K5%1/10W
R89841-216-821-11 METAL CHIP1K5%1/10W
R89851-216-841-11 METAL CHIP47K5%1/10W
R89861-216-833-11 METAL CHIP10K5%1/10W
R89871-216-833-11 METAL CHIP10K5%1/10W
R89881-216-841-11 METAL CHIP47K5%1/10W
R89891-216-841-11 METAL CHIP47K5%1/10W
R89071-216-826-11 METAL CHIP2.7K5%1/10W
R89081-216-825-11 METAL CHIP2.2K5%1/10W
R89091-216-833-11 METAL CHIP10K5%1/10W
R89181-216-833-11 METAL CHIP10K5%1/10W
R89191-216-833-11 METAL CHIP10K5%1/10W
R89201-216-821-11 METAL CHIP1K5%1/10W
R89211-216-833-11 METAL CHIP10K5%1/10W
R89221-216-809-11 METAL CHIP1005%1/10W
R89231-216-864-11 SHORT CHIP0
R89241-216-825-11 METAL CHIP2.2K5%1/10W
R89251-216-864-11 SHORT CHIP0
R89271-216-809-11 METAL CHIP1005%1/10W
R89281-218-855-11 METAL CHIP2.2K0.5% 1/10W
R89291-218-861-11 METAL CHIP3.9K0.5% 1/10W
R89301-216-864-11 SHORT CHIP0
R89311-216-864-11 SHORT CHIP0
R89321-216-841-11 METAL CHIP47K5%1/10W
R89331-216-833-11 METAL CHIP10K5%1/10W
R89341-216-829-11 METAL CHIP4.7K5%1/10W
R89351-216-825-11 METAL CHIP2.2K5%1/10W
R89381-216-841-11 METAL CHIP47K5%1/10W
R89401-216-825-11 METAL CHIP2.2K5%1/10W
R89411-216-805-11 METAL CHIP475%1/10W
R89421-216-805-11 METAL CHIP475%1/10W
IC55006-701-972-01 IC TC90A69F (ELP)
IC55016-705-469-01 IC BA50BC0FP-E2
IC55028-753-212-10 IC CXA2163AQ-T6
IC55036-706-475-01 IC TC7SET02FU(T5RSOJF)
IC55046-803-172-11 IC SAA5360HL/M1/0004,518
IC55056-703-175-01 IC PST3629UL
IC55076-706-478-01 IC TC7SET08FU(T5RSOJF)
IC57008-749-925-00 IC TK11819MTL
IC57016-705-469-01 IC BA50BC0FP-E2
IC57036-703-781-01 IC S-80843CLUA-B64T2G
R55001-216-809-11 METAL CHIP1005%1/10W
R55021-216-817-11 METAL CHIP4705%1/10W
R55041-218-841-11 METAL CHIP5600.5% 1/10W
R55061-216-809-11 METAL CHIP1005%1/10W
R55071-218-839-11 METAL CHIP4700.5% 1/10W
R55081-218-839-11 METAL CHIP4700.5% 1/10W
R55091-218-865-11 METAL CHIP5.6K0.5% 1/10W
R55101-216-825-11 METAL CHIP2.2K5%1/10W
R55111-216-809-11 METAL CHIP1005%1/10W
R55121-218-839-11 METAL CHIP4700.5% 1/10W
R55131-218-839-11 METAL CHIP4700.5% 1/10W
R55141-218-839-11 METAL CHIP4700.5% 1/10W
R55151-218-835-11 METAL CHIP3300.5% 1/10W
R55161-216-821-11 METAL CHIP1K5%1/10W
R55171-216-825-11 METAL CHIP2.2K5%1/10W
R55181-216-864-11 SHORT CHIP0
R55191-216-820-11 METAL CHIP8205%1/10W
R55201-216-805-11 METAL CHIP475%1/10W
R55211-216-805-11 METAL CHIP475%1/10W
R55221-216-821-11 METAL CHIP1K5%1/10W
R55231-216-821-11 METAL CHIP1K5%1/10W
R55241-218-845-11 METAL CHIP8200.5% 1/10W
R55251-218-845-11 METAL CHIP8200.5% 1/10W
R55261-218-841-11 METAL CHIP5600.5% 1/10W
R55271-218-841-11 METAL CHIP5600.5% 1/10W
R55281-216-834-11 METAL CHIP12K5%1/10W
R55291-218-867-11 METAL CHIP6.8K0.5% 1/10W
R55301-216-834-11 METAL CHIP12K5%1/10W
R55311-218-867-11 METAL CHIP6.8K0.5% 1/10W
R55321-216-821-11 METAL CHIP1K5%1/10W
R55331-218-837-11 METAL CHIP3900.5% 1/10W
R55341-216-821-11 METAL CHIP1K5%1/10W
R55351-218-839-11 METAL CHIP4700.5% 1/10W
R55361-218-845-11 METAL CHIP8200.5% 1/10W
R55371-218-845-11 METAL CHIP8200.5% 1/10W
R55421-216-821-11 METAL CHIP1K5%1/10W
R55441-216-821-11 METAL CHIP1K5%1/10W
R55461-216-838-11 METAL CHIP27K5%1/10W
R55471-218-871-11 METAL CHIP10K0.5% 1/10W
R55481-220-397-11 METAL CHIP4.7M5%1/10W
R55491-220-397-11 METAL CHIP4.7M5%1/10W
R55501-216-805-11 METAL CHIP475%1/10W
– 72 –
Page 74
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R55511-218-871-11 METAL CHIP10K0.5% 1/10W
R55521-216-809-11 METAL CHIP1005%1/10W
R55531-216-809-11 METAL CHIP1005%1/10W
R55541-216-809-11 METAL CHIP1005%1/10W
R55551-216-809-11 METAL CHIP1005%1/10W
R55561-216-809-11 METAL CHIP1005%1/10W
R55571-216-809-11 METAL CHIP1005%1/10W
R55581-216-809-11 METAL CHIP1005%1/10W
R55591-216-809-11 METAL CHIP1005%1/10W
R55601-216-809-11 METAL CHIP1005%1/10W
R55611-216-809-11 METAL CHIP1005%1/10W
R55621-216-809-11 METAL CHIP1005%1/10W
R55631-216-809-11 METAL CHIP1005%1/10W
R55641-216-812-11 METAL CHIP1805%1/10W
R55651-216-817-11 METAL CHIP4705%1/10W
R55661-216-808-11 METAL CHIP825%1/10W
R55671-216-817-11 METAL CHIP4705%1/10W
R55681-216-817-11 METAL CHIP4705%1/10W
R55691-216-864-11 SHORT CHIP0
R55701-216-817-11 METAL CHIP4705%1/10W
R55711-216-864-11 SHORT CHIP0
R55721-216-817-11 METAL CHIP4705%1/10W
R55731-216-817-11 METAL CHIP4705%1/10W
R55741-216-821-11 METAL CHIP1K5%1/10W
R55751-216-821-11 METAL CHIP1K5%1/10W
R55761-216-864-11 SHORT CHIP0
R55771-216-809-11 METAL CHIP1005%1/10W
R55781-218-887-11 METAL CHIP47K0.5% 1/10W
R55791-216-809-11 METAL CHIP1005%1/10W
R55821-216-809-11 METAL CHIP1005%1/10W
R55831-216-841-11 METAL CHIP47K5%1/10W
R55841-216-809-11 METAL CHIP1005%1/10W
R55851-216-809-11 METAL CHIP1005%1/10W
R55871-216-809-11 METAL CHIP1005%1/10W
R55881-216-817-11 METAL CHIP4705%1/10W
R55891-216-809-11 METAL CHIP1005%1/10W
R55901-216-817-11 METAL CHIP4705%1/10W
R55911-216-809-11 METAL CHIP1005%1/10W
R55921-216-817-11 METAL CHIP4705%1/10W
R55961-216-809-11 METAL CHIP1005%1/10W
R55981-216-809-11 METAL CHIP1005%1/10W
R55991-216-809-11 METAL CHIP1005%1/10W
R56021-216-809-11 METAL CHIP1005%1/10W
R56041-216-825-11 METAL CHIP2.2K5%1/10W
R56051-216-816-11 METAL CHIP3905%1/10W
R56061-216-864-11 SHORT CHIP0
R56101-216-821-11 METAL CHIP1K5%1/10W
R56131-211-990-11 METAL CHIP750.5% 1/10W
R56141-211-990-11 METAL CHIP750.5% 1/10W
R56151-211-990-11 METAL CHIP750.5% 1/10W
R56161-218-895-11 METAL CHIP100K0.5% 1/10W
R56171-218-895-11 METAL CHIP100K0.5% 1/10W
R56181-216-809-11 METAL CHIP1005%1/10W
R56191-216-821-11 METAL CHIP1K5%1/10W
R56201-216-864-11 SHORT CHIP0
R56211-216-809-11 METAL CHIP1005%1/10W
R56221-216-809-11 METAL CHIP1005%1/10W
R56231-216-864-11 SHORT CHIP0
R56241-216-864-11 SHORT CHIP0
R56251-216-864-11 SHORT CHIP0
R56261-216-864-11 SHORT CHIP0
R56271-216-864-11 SHORT CHIP0
R56281-216-864-11 SHORT CHIP0
KF-E42A10/E50A10
KRM-GA004 RM-GA004
AS
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R56291-216-864-11 SHORT CHIP0
R56321-216-864-11 SHORT CHIP0
R56331-216-864-11 SHORT CHIP0
R56341-216-864-11 SHORT CHIP0
R56351-216-864-11 SHORT CHIP0
R56361-216-864-11 SHORT CHIP0
R56381-216-809-11 METAL CHIP1005%1/10W
R56401-216-809-11 METAL CHIP1005%1/10W
R56411-216-809-11 METAL CHIP1005%1/10W
R56421-216-821-11 METAL CHIP1K5%1/10W
R57001-216-821-11 METAL CHIP1K5%1/10W
R57011-216-845-11 METAL CHIP100K5%1/10W
R57021-216-809-11 METAL CHIP1005%1/10W
R57031-216-809-11 METAL CHIP1005%1/10W
R57041-216-809-11 METAL CHIP1005%1/10W
R57051-216-809-11 METAL CHIP1005%1/10W
R57101-216-864-11 SHORT CHIP0
R57121-216-825-11 METAL CHIP2.2K5%1/10W
R57141-216-809-11 METAL CHIP1005%1/10W
R57161-216-809-11 METAL CHIP1005%1/10W
R57171-216-809-11 METAL CHIP1005%1/10W
R57181-216-864-11 SHORT CHIP0
R57201-216-864-11 SHORT CHIP0
R57211-216-809-11 METAL CHIP1005%1/10W
R57231-216-809-11 METAL CHIP1005%1/10W
R57241-216-809-11 METAL CHIP1005%1/10W
R57251-216-809-11 METAL CHIP1005%1/10W
R57271-216-809-11 METAL CHIP1005%1/10W
R57281-216-825-11 METAL CHIP2.2K5%1/10W
R57291-216-864-11 SHORT CHIP0
R57311-216-864-11 SHORT CHIP0
R57321-216-829-11 METAL CHIP4.7K5%1/10W
R57331-216-828-11 METAL CHIP3.9K5%1/10W
R57351-216-829-11 METAL CHIP4.7K5%1/10W
R57361-216-826-11 METAL CHIP2.7K5%1/10W
R57371-216-809-11 METAL CHIP1005%1/10W
R57381-216-825-11 METAL CHIP2.2K5%1/10W
R57391-216-809-11 METAL CHIP1005%1/10W
R57411-216-857-11 METAL CHIP1M5%1/10W
R57431-216-864-11 SHORT CHIP0
R57461-216-805-11 METAL CHIP475%1/10W
R57471-216-805-11 METAL CHIP475%1/10W
R57481-216-864-11 SHORT CHIP0
R57501-216-829-11 METAL CHIP4.7K5%1/10W
R57511-216-864-11 SHORT CHIP0
R57531-216-857-11 METAL CHIP1M5%1/10W
R57541-216-829-11 METAL CHIP4.7K5%1/10W
R57561-218-871-11 METAL CHIP10K0.5% 1/10W
R57571-218-871-11 METAL CHIP10K0.5% 1/10W
R57581-218-879-11 METAL CHIP22K0.5% 1/10W
IC60006-705-810-01 IC MCZ3001DB
IC60026-705-464-01 IC BA50BC0T
IC60036-705-466-01 IC BA90BC0T
IC60046-705-464-01 IC BA50BC0T
IC60076-708-388-01 IC KA278RA05CYDTU
IC60086-708-175-01 IC MR4010-7103
IC60108-759-682-42 IC MM1431ATT
IC60118-759-682-42 IC MM1431ATT
IC60126-708-388-01 IC KA278RA05CYDTU
IC64006-702-490-01 IC TA8258HQ
< JUMPER RESISTOR >
JR60011-216-864-11 SHORT CHIP0
JR60021-216-864-11 SHORT CHIP0
R60021-215-904-11 METAL OXIDE100K5%2W
R60031-215-904-11 METAL OXIDE100K5%2W
R60051-216-864-11 SHORT CHIP0
R60061-218-871-11 METAL CHIP10K0.5% 1/10W
R60071-218-855-11 METAL CHIP2.2K0.5% 1/10W
R60191-218-823-11 METAL CHIP1000.5% 1/10W
R60201-218-870-11 METAL CHIP9.1K0.5% 1/10W
R60221-218-859-11 METAL CHIP3.3K0.5% 1/10W
R60231-218-831-11 METAL CHIP2200.5% 1/10W
R60291-245-472-21 METAL270K1%1/4W
R60301-245-471-21 METAL240K1%1/4W
R60311-245-471-21 METAL240K1%1/4W
R60321-245-471-21 METAL240K1%1/4W
R60351-218-877-11 METAL CHIP18K0.5% 1/10W
R60421-211-991-11 METAL CHIP820.5% 1/10W
R60511-218-871-11 METAL CHIP10K0.5% 1/10W
R60561-216-817-11 METAL CHIP4705%1/10W
R60571-243-979-71 METAL OXIDE0.15%2W
R60581-249-385-11 CARBON2.25%1/4W
R60591-216-864-11 SHORT CHIP0
R60601-216-829-11 METAL CHIP4.7K5%1/10W
R60611-216-833-11 METAL CHIP10K5%1/10W
R60621-216-833-11 METAL CHIP10K5%1/10W
R60631-216-821-11 METAL CHIP1K5%1/10W
R60641-216-821-11 METAL CHIP1K5%1/10W
R60651-216-821-11 METAL CHIP1K5%1/10W
R60681-216-864-11 SHORT CHIP0
R60701-216-833-11 METAL CHIP10K5%1/10W
R60721-218-877-11 METAL CHIP18K0.5% 1/10W
R60741-218-863-11 METAL CHIP4.7K0.5% 1/10W
R60861-216-350-11 METAL OXIDE1.25%1W
R60891-216-864-11 SHORT CHIP0
R60981-220-340-11 METAL CHIP470K5%1/2W
R61001-202-933-61 FUSIBLE0.110% 1/2W
R62431-216-835-11 METAL CHIP15K5%1/10W
R62441-218-875-11 METAL CHIP15K0.5% 1/10W
R62451-215-865-11 METAL OXIDE2205%1W
R6246 0 1-247-289-00 METAL8.2M5%1W
R62481-216-828-11 METAL CHIP3.9K5%1/10W
R62491-219-759-11 METAL1M5%1/2W
R62501-216-827-11 METAL CHIP3.3K5%1/10W
R62511-216-828-11 METAL CHIP3.9K5%1/10W
R62521-216-825-11 METAL CHIP2.2K5%1/10W
R62531-216-833-11 METAL CHIP10K5%1/10W
R62541-216-833-11 METAL CHIP10K5%1/10W
– 75 –
Page 77
KF-E42A10/E50A10
RM-GA004 RM-GA004
GT
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
R62551-216-344-00 METAL OXIDE0.395%1W
R62571-216-349-00 METAL OXIDE15%1W
R62591-240-251-11 CEMENTED6.85%10W
R62611-249-417-11 CARBON1K5%1/4W
R62621-216-829-11 METAL CHIP4.7K5%1/10W
HBHA
The components identified by
shading and mark
cal for safety.
Replace only with part number
specified.
R62631-249-389-11 CARBON4.75%1/4W
R62671-216-829-11 METAL CHIP4.7K5%1/10W
R62681-216-825-11 METAL CHIP2.2K5%1/10W
R62731-249-389-11 CARBON4.75%1/4W
R62771-216-821-11 METAL CHIP1K5%1/10W
R62781-216-827-11 METAL CHIP3.3K5%1/10W
R62791-216-833-11 METAL CHIP10K5%1/10W
R62801-216-833-11 METAL CHIP10K5%1/10W
R62811-216-833-11 METAL CHIP10K5%1/10W
R62831-243-979-71 METAL OXIDE0.15%2W
R62841-216-864-11 SHORT CHIP0
R62851-216-832-11 METAL CHIP8.2K5%1/10W
R62861-216-834-11 METAL CHIP12K5%1/10W
R62871-218-875-11 METAL CHIP15K0.5% 1/10W
R62881-218-863-11 METAL CHIP4.7K0.5% 1/10W
R62911-216-864-11 SHORT CHIP0
R63391-216-864-11 SHORT CHIP0
R64001-216-833-11 METAL CHIP10K5%1/10W
R64011-216-821-11 METAL CHIP1K5%1/10W
R64021-216-857-11 METAL CHIP1M5%1/10W
R64031-216-833-11 METAL CHIP10K5%1/10W
R64041-216-821-11 METAL CHIP1K5%1/10W
R64091-216-825-11 METAL CHIP2.2K5%1/10W
R64101-216-825-11 METAL CHIP2.2K5%1/10W
R64111-216-825-11 METAL CHIP2.2K5%1/10W
R64121-216-825-11 METAL CHIP2.2K5%1/10W
R64131-216-833-11 METAL CHIP10K5%1/10W
R64141-216-845-11 METAL CHIP100K5%1/10W
R64151-216-845-11 METAL CHIP100K5%1/10W
R64161-216-833-11 METAL CHIP10K5%1/10W
R64241-216-833-11 METAL CHIP10K5%1/10W
R64251-216-833-11 METAL CHIP10K5%1/10W
R64261-216-833-11 METAL CHIP10K5%1/10W
R64271-216-813-11 METAL CHIP2205%1/10W
R64281-216-813-11 METAL CHIP2205%1/10W
R64291-216-864-11 SHORT CHIP0
R64301-216-864-11 SHORT CHIP0
R70011-218-676-11 METAL CHIP2200.5% 1/10W
R70021-218-684-11 METAL CHIP4700.5% 1/10W
R70031-218-691-11 METAL CHIP9100.5% 1/10W
R70041-218-698-11 METAL CHIP1.8K0.5% 1/10W
R70051-218-706-11 METAL CHIP3.9K0.5% 1/10W
R70201-216-823-11 METAL CHIP1.5K5%1/10W
R70211-216-805-11 METAL CHIP475%1/10W
R70221-216-833-11 METAL CHIP10K5%1/10W
R70231-216-833-11 METAL CHIP10K5%1/10W
R70241-216-813-11 METAL CHIP2205%1/10W
R70251-216-813-11 METAL CHIP2205%1/10W
R70261-216-833-11 METAL CHIP10K5%1/10W
R70271-216-833-11 METAL CHIP10K5%1/10W
R70281-216-813-11 METAL CHIP2205%1/10W
R70291-216-833-11 METAL CHIP10K5%1/10W
R70301-216-833-11 METAL CHIP10K5%1/10W
R70311-216-833-11 METAL CHIP10K5%1/10W
R70321-216-813-11 METAL CHIP2205%1/10W
R70331-216-813-11 METAL CHIP2205%1/10W
R70341-216-833-11 METAL CHIP10K5%1/10W
R70351-216-833-11 METAL CHIP10K5%1/10W
R70391-216-833-11 METAL CHIP10K5%1/10W
R70401-216-864-11 SHORT CHIP0
R70421-216-864-11 SHORT CHIP0
R70451-216-864-11 SHORT CHIP0
HB
REF. NO.PART NO.DESCRIPTIONREMARK
––––––– ––––––––––––––––––––––––––
J71021-568-267-11 JACK
< RESISTOR >
R71031-216-849-11 METAL CHIP220K5%1/10W
R71041-216-849-11 METAL CHIP220K5%1/10W
R71051-218-676-11 METAL CHIP2200.5% 1/10W
R71061-216-809-11 METAL CHIP1005%1/10W
R71091-216-821-11 METAL CHIP1K5%1/10W
R71101-216-821-11 METAL CHIP1K5%1/10W
R71111-216-864-11 SHORT CHIP0
R71231-216-864-11 SHORT CHIP0
R71241-218-676-11 METAL CHIP2200.5% 1/10W
R71251-218-676-11 METAL CHIP2200.5% 1/10W
R71261-216-864-11 SHORT CHIP0
R71281-216-797-11 METAL CHIP105%1/10W
R71291-216-797-11 METAL CHIP105%1/10W
R72001-216-853-11 METAL CHIP470K5%1/10W
R72021-216-845-11 METAL CHIP100K5%1/10W
R72051-216-805-11 METAL CHIP475%1/10W
R72061-216-864-11 SHORT CHIP0
R72071-216-864-11 SHORT CHIP0
R72081-216-864-11 SHORT CHIP0
R72091-216-805-11 METAL CHIP475%1/10W
R72101-216-851-11 METAL CHIP330K5%1/10W
R72111-216-851-11 METAL CHIP330K5%1/10W
R72161-216-833-11 METAL CHIP10K5%1/10W
R72171-216-833-11 METAL CHIP10K5%1/10W
R72181-216-805-11 METAL CHIP475%1/10W
R72191-216-805-11 METAL CHIP475%1/10W
R72221-216-864-11 SHORT CHIP0
R72231-216-864-11 SHORT CHIP0
R72271-216-821-11 METAL CHIP1K5%1/10W
R72291-216-845-11 METAL CHIP100K5%1/10W
R72311-216-864-11 SHORT CHIP0
R72321-216-864-11 SHORT CHIP0
R72331-216-864-11 SHORT CHIP0
R72341-216-864-11 SHORT CHIP0
R72351-216-864-11 SHORT CHIP0
R95011-208-663-11 METAL CHIP1500.5% 1/16W
R95021-208-663-11 METAL CHIP1500.5% 1/16W
R95051-218-973-11 RES-CHIP47K5%1/16W
R95061-218-941-81 RES-CHIP1005%1/16W
R95071-218-990-81 SHORT CHIP0
R95081-218-990-81 SHORT CHIP0
R95091-218-990-81 SHORT CHIP0
R95101-208-663-11 METAL CHIP1500.5% 1/16W
R95111-218-935-11 RES-CHIP335%1/16W
R95121-208-860-81 METAL CHIP750.5% 1/16W
R95131-208-860-81 METAL CHIP750.5% 1/16W
R95141-208-860-81 METAL CHIP750.5% 1/16W
R95151-218-941-81 RES-CHIP1005%1/16W
R95181-218-965-11 RES-CHIP10K5%1/16W
R95191-218-935-11 RES-CHIP335%1/16W
IC95006-706-257-01 IC FMS6418AM16X
IC95018-759-278-58 IC NJM4558V-TE2
IC95026-704-819-01 IC CS4335-KSZR
IC95036-704-407-01 IC PQ1CZ41H2ZPH
IC95046-704-001-01 IC BR24L02F-WE2
IC95056-704-499-01 IC SII9993CTG100
IC95066-703-042-01 IC CD4052BNSR
IC95096-550-014-01 TRANSISTOR SSM6N15FU(TE85R)
IC95148-759-278-58 IC NJM4558V-TE2
IC95176-805-603-01 IC HD64F3694FXV-P1
IC95218-759-473-95 IC UPC2905T-E1
IC95226-703-175-01 IC PST3629UL
R95251-216-815-11 METAL CHIP3305%1/10W
R95261-208-911-11 METAL CHIP10K0.5% 1/16W
R95281-218-969-11 RES-CHIP22K5%1/16W
R95291-218-982-11 RES-CHIP270K5%1/16W
R95301-218-953-11 RES-CHIP1K5%1/16W
R95311-218-961-11 RES-CHIP4.7K5%1/16W
R95321-218-849-11 METAL CHIP1.2K0.5% 1/10W
R95331-218-957-11 RES-CHIP2.2K5%1/16W
R95341-208-677-11 METAL CHIP5600.5% 1/16W
R95351-218-977-11 RES-CHIP100K5%1/16W
R95381-208-659-11 METAL CHIP1000.5% 1/16W
R95391-218-953-11 RES-CHIP1K5%1/16W
R95401-218-961-11 RES-CHIP4.7K5%1/16W
R95411-218-849-11 METAL CHIP1.2K0.5% 1/10W
R95421-218-982-11 RES-CHIP270K5%1/16W
R95431-218-950-11 RES-CHIP5605%1/16W
R95441-218-706-11 METAL CHIP3.9K0.5% 1/10W
R95461-218-706-11 METAL CHIP3.9K0.5% 1/10W
R95471-218-977-11 RES-CHIP100K5%1/16W
R95481-208-911-11 METAL CHIP10K0.5% 1/16W
R95521-218-949-11 RES-CHIP4705%1/16W
R95551-218-706-11 METAL CHIP3.9K0.5% 1/10W
R95561-218-961-11 RES-CHIP4.7K5%1/16W
R95571-218-706-11 METAL CHIP3.9K0.5% 1/10W
R95581-218-961-11 RES-CHIP4.7K5%1/16W
R95591-216-809-11 METAL CHIP1005%1/10W
R95601-218-990-81 SHORT CHIP0
R95621-216-809-11 METAL CHIP1005%1/10W
R95631-208-697-11 METAL CHIP3.9K0.5% 1/16W
R95641-218-969-11 RES-CHIP22K5%1/16W
R95651-216-845-11 METAL CHIP100K5%1/10W
R95661-218-990-81 SHORT CHIP0
R95691-216-845-11 METAL CHIP100K5%1/10W
R95721-218-969-11 RES-CHIP22K5%1/16W
R95741-218-941-81 RES-CHIP1005%1/16W
R96251-218-977-11 RES-CHIP100K5%1/16W
R96261-218-965-11 RES-CHIP10K5%1/16W
R96271-218-941-81 RES-CHIP1005%1/16W
R98011-218-990-81 SHORT CHIP0
R98021-218-990-81 SHORT CHIP0
R98031-218-990-81 SHORT CHIP0
R98041-218-990-81 SHORT CHIP0
R98051-218-990-81 SHORT CHIP0
R98061-218-965-11 RES-CHIP10K5%1/16W
R98501-216-833-11 METAL CHIP10K5%1/10W
R98511-216-821-11 METAL CHIP1K5%1/10W
R98521-218-644-11 METAL CHIP100.5% 1/10W
R98531-218-977-11 RES-CHIP100K5%1/16W
R98541-218-977-11 RES-CHIP100K5%1/16W
R98601-208-687-11 METAL CHIP1.5K0.5% 1/16W
R98611-208-661-11 METAL CHIP1200.5% 1/16W
R98641-208-683-11 METAL CHIP1K0.5% 1/16W
R98661-218-953-11 RES-CHIP1K5%1/16W
R98671-218-953-11 RES-CHIP1K5%1/16W
R98681-218-965-11 RES-CHIP10K5%1/16W
R98691-218-965-11 RES-CHIP10K5%1/16W
R98821-208-860-81 METAL CHIP750.5% 1/16W
R98841-208-860-81 METAL CHIP750.5% 1/16W
R98881-208-683-11 METAL CHIP1K0.5% 1/16W
R98901-208-860-81 METAL CHIP750.5% 1/16W
R98911-218-941-81 RES-CHIP1005%1/16W
R98961-218-990-81 SHORT CHIP0
R98981-218-990-81 SHORT CHIP0
R99001-218-990-81 SHORT CHIP0
R99021-218-990-81 SHORT CHIP0
R99031-218-990-81 SHORT CHIP0
R99041-218-989-11 RES-CHIP1M5%1/16W
R99051-208-663-11 METAL CHIP1500.5% 1/16W
R99061-208-663-11 METAL CHIP1500.5% 1/16W
R99071-208-663-11 METAL CHIP1500.5% 1/16W
R71811-216-801-11 METAL CHIP225%1/10W
R71821-216-801-11 METAL CHIP225%1/10W
R71851-216-864-11 SHORT CHIP0
R71861-216-864-11 SHORT CHIP0
R71871-216-864-11 SHORT CHIP0
Thank you for choosing this Sony product.
Before operating the TV, please read this manual
thoroughly and retain it for future reference.
Trademark information
• Licensed by BBE Sound, Inc. under USP4638258,
4482866. “BBE” and BBE symbol are trademarks of BBE
Sound, Inc.
• TruSurround XT, SRS and symbol are trademarks
of SRS Labs, Inc.
• TruSurround XT technology is incorporated under license
from SRS Labs, Inc.
•This TV incorporates
Interface (HDMI™) technology. HDMI, the HDMI logo
and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
• WEGA, Grand WEGA, WEGA GATE, Steady Sound,
Digital Reality Creation and CineMotion are registered
trademarks of Sony Corporation.
High-Definition Multimedia
GB
2
Page 86
Table of Contents
Safety Information ....................................... 5
Overview of the remote ............................ 8
Index ......................................................... 56
GB
4
Page 88
Safety Information
To prevent fire or shock hazard, do not expose the LCD
projection TV to rain or moisture.
Dangerously high voltages are present inside the LCD
projection TV. Do not open the cabinet. Refer servicing to
qualified personnel only.
For general safety:
• Do not expose the LCD projection
TV to rain or moisture.
• Do not open the rear cover.
• This set should be operated only from
the type of power source indicated on the serial/model
plate.
If you are not sure of the type of electrical power supplied
to your home, consult your dealer or local power
company. For those sets designed to operate from battery
power, refer to the operating instructions.
For safe installation:
• Never cover the slots and openings with
a cloth or other materials.
• Avoid operating the LCD projection TV at temperatures
below 5ºC.
• If the LCD projection TV is transported directly from a
cold to a warm location, or if the room temperature has
changed suddenly, the picture may be blurred or show
poor color. This is because moisture has condensed on the
mirror or lenses inside. If this happens, let the moisture
evaporate before using the LCD projection TV.
• If direct sunlight or other strong illumination shines on the
screen, part of the screen may appear white due to
reflections from behind the screen. This is a structural
property of the LCD projection TV.
Do not expose the screen to direct illumination or sunlight.
• Do not install the appliance in a
confined space, such as a bookcase
or built-in cabinet.
• Do not place the set on an unstable cart, stand, table or
shelf. The set may fall, causing serious injury to a child or
an adult and serious damage to the set. Use only a cart or
stand recommended by the manufacturer for the specific
model of LCD projection TV. An appliance and cart
combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
• Do not block the ventilation openings.
• Do not use power-line operated sets near water — for
example, near a bathtub, washbowl, kitchen sink,
swimming pool, etc.
• Do not install the LCD projection TV in hot, humid or
excessively dusty places.
• Do not allow anything to
rest on or roll over the
power cord, and do not
place the set where the
power cord is subject to
wear or abuse.
• Do not install the LCD
projection TV where it may
be exposed to mechanical
vibrations.
• When the set exhibits a distinct change in performance, it
indicates a need for service.
For safe operations:
• Do not operate the LCD projection TV on anything but
220-240 V AC, 50/60 Hz.
• Do not operate the LCD projection
TV if any liquid or solid object
falls in it — have it checked
immediately.
• Never push objects of any
kind into the set through the
cabinet slots as they may
touch dangerous voltage
points or short out parts that
could result in a fire or
electric shock. Never spill
liquid of any kind on the set.
• Leave enough space between the LCD projection TV or
furniture and an outlet so that you can plug in/out easily.
Continued
5
GB
Page 89
• Unplug the AC power cord during
lightning storm.
• Do not keep the LCD
projection TV plugged in if
you are not going to use it
for several days. Even if
your LCD projection TV is
turned off, it is still
connected to AC power
when plugged into an
outlet.
• Do not pull the power cord to
disconnect the LCD
projection TV. Pull it out by
the plug.
• Do not plug in too many
appliances to the same
power jack. Do not damage
the power cord.
• Do not place any objects on
the LCD projection TV. The
apparatus shall not be
exposed to dripping or
splashing and that no objects
filled with liquids, such as
vases, shall be placed on the
apparatus.
• To prevent fire, keep
inflammable objects or naked lights (e.g. candles) away
from the LCD projection TV.
• If a snapping or popping sound from a TV set is
continuous or frequent while the TV is operating, unplug
the TV and consult your dealer or service technician. It is
normal for some TV sets to make occasional snapping or
popping sounds, particularly when being turned on or off.
• Give careful consideration to the environment when
disposing of batteries.
Carry the LCD projection TV in the specified manner
If you carry the LCD projection TV in a manner other than
the specified manner and without the specified number of
persons, it may drop and a serious injury may be caused. Be
sure to follow the instructions mentioned below.
• Carry the LCD projection TV with
the specified number of persons (see
page 12).
• Before carrying the LCD projection TV, disconnect any
accessories or cables.
• Do not carry the LCD projection TV
holding the screen edges.
Caution
Do not use the LCD projection TV at altitudes higher than
4000 m, as doing so might cause malfunctions.
Cleaning
Clean the rear cover area of the LCD projection TV
regularly. Dust in rear cover area may cause a problem
with the cooling system of the LCD projection TV set.
• To remove hard contamination, use a cloth moistened with
a solution of mild detergent and water. Do not use a spray
cleaning solution directly to the TV. It should only be used
to moisten the cleaning cloth.
• Clean the cabinet of the LCD
projection TV with a dry soft
cloth. To remove dust from the
screen, wipe it gently with a
soft cloth. Stubborn stains may
be removed with a cloth
slightly dampened with a
solution of mild soap and warm water. Never use strong
solvents such as thinner or benzine for cleaning. If picture
brightness decreases over time, it may be necessary to
clean the inside of the LCD projection TV. Consult
qualified service personnel.
• Unplug the AC power cord when cleaning this unit. If not,
it may result in electric shock.
• Do not rub, touch, or tap the surface of the screen with
sharp or abrasive items, like a ball point pen or a screw
driver. This type of contact may result in a scratched
screen.
About the LCD projection TV
Although the LCD projection TV is made with highprecision technology, black dots may appear or bright points
of light (red, blue, or green) may appear constantly on the
screen. This is a structural property of the panel and is not a
malfunction.
• Do not carry the LCD projection TV
holding the speaker grill.
• Hold the LCD projection TV tightly when carrying it.
GB
6
Page 90
Projection lamp
• Your LCD projection TV uses a projection lamp as its
light source. It is time to replace the lamp with a new one
(not supplied) when:
– the lamp r eplacement indicator on the front p anel blinks
in red,
– screen images become dark,
– no image appears on the display after prolonged use.
• In rare instances, the bulb may pop inside the lamp unit,
but the lamp unit is designed to contain all of broken glass
pieces inside the lamp unit. (See “Replacing the lamp” on
page 48.)
• When the lamp eventually burns out, you may hear a
noticeable pop sound. This is normal and is inhe rent in this
type of lamp.
Cooling fan
This LCD projection TV uses a cooling fan. You may hear
some fan noise (depending on the placement of the LCD
projection TV), which may be more noticeable during the
night, or when ambient noise is particularly low.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other
European countries with separate collection
systems)
This symbol is on the remote control.
GB
7
Page 91
Overview of the remote
q
q
q
q
q
1/ – Input select / Text hold
1
2
3
4
5
6
7
8
9
f
In TV mode (page 21): Selects the input source from equipment connected to the
d
TV jacks.
In Text mode (page 19): Holds the current page.
2 % – Muting (page 18)
Mutes the sound.
3 Function buttons (page 45)
s
• Selects the connected equipment you want to operate with this remote. The
button of the equipment which the remote can operate lights up when
operation buttons are pressed.
• Used to program the remote to operate Sony video/audio equipment.
4 Number buttons
a
In TV mode (page 18): Selects channels.
In Text mode (page 19): Enters the three-digit page number to select the page.
;
5 / – Text (page 19)
Displays Text.
6
This button does not work with this model.
7 M/m/</,/ (page24)
Selects the item and setting when operating WEGA GATE.
8 RETURN
Returns to the previous page when operating WEGA GATE.
9 WEGA GATE (page 24)
Displays WEGA GATE which includes TV List, External Inputs, and Settings.
0 TOOLS (page 20)
Enables you to access various viewing options and change/make adjustments
according to the source and screen mode.
qa/ – Info / Text reveal
In TV mode (page 18): Displays information such as current channel number and
screen mode.
In Text mode (page 19): Reveals hidden information (e.g., answers to quizzes).
qs/-/-- – Previous channel (page 18)
Returns to the previous channel watched (for more than five seconds).
When operating DVD, it works as the “Execute” button (page 46).
qd TV "/1 – TV standby (page 18)
Switches off the TV temporarily. The 1 (standby) indicator on the front of the
TV lights up. Press again to switch on the TV from the standby mode.
qf "/1 – Power (page 46)
Switches the VCR, DVD, or audio equipment connected to the TV on or off.
GB
8
Page 92
qg
qh
qj
qk
ql
w;
wa
ws
wd
wf
wg
qg/ – Sleep Timer (page 41)
In TV mode (page 41): Activates Sleep Timer.
In Text mode (page 19): Exits the Text service.
qh – TV mode (page 21)
Exits Text mode, or returns to TV mode.
qj – Picture mode (page 28)
es
ea
e;
wl
wk
Selects the picture mode.
qk 9 – Sound mode (page 31)
Selects the sound mode.
ql DVD/VCR operating buttons (page 45)
Operates the connected DVD and VCR.
w; VISUAL SEARCH (page 46)
Works with connected equipment which has the visual search function.
wa 2 +/- – Volume (page 18)
Adjusts the volume.
ws DVD/VCR record buttons (page 45)
REC: Records the source
REC PAUSE: Pauses recording
wj
REC STOP: Stops recording
wd DVD TOP MENU (page 46)
Displays the top menu of the connected DVD equipment.
wh
wf DVD MENU (page 46)
Displays the menu of a DVD.
wg POWER SAVING
This function does not work with this model.
wh F1/F2 (page 46)
Selects the function of connected equipment.
wj PROG +/-// (page 18)
In TV mode (page 18): Selects the next (+) or previous (-) channel.
In Text mode (page 19): Selects the next (+) or previous (-) page.
wk Colored buttons
In Text mode (page 19): Used for Fastext.
wl
– Screen mode (page 20)
Selects the type of the wide mode.
e; – Surround (page 32)
Selects the surround sound effect.
ea – Picture Freeze (page 19)
Freezes the current picture to display it on the left screen.
es
A/B/ – Text enlarge
In TV mode (page 18): Switches the sound between stereo and mono, or
languages in bilingual programs.
In Text mode (page 19): Switches the text size.
Tip
The PROG+, H (Play), A/B and number 5 buttons have tactile dots. Use the tactile dots
as references when operating the TV.
GB
9
Page 93
Overview of the TV buttons and indicators
215934678
To open the panel
To open the front panel of your TV,
push up the panel door just under
the mark.
WEGA GATE
WEGA GATE
PROG
PROG
1 WEGA GATE (page 24)
Displays WEGA GATE.
2
Confirms the selection or setting.
Selects the video equipment connected to the TV’s video inputs.
3 2 +/-/ /
• Increases (+) or decreases (-) the volume.
• In TV menu: Moves through the options left ( ) or right ( ).
4 PROG +/-/ /
In TV mode: Selects the next (+) or previous (-) channel.
In TV menu: Moves through the options up ( ) or down ().
5 indicator (page 41)
Lights up in amber when the Sleep Timer/On Timer is set.
6 indicator
Flashes up in red when the lamp for the light source has burned out.
7 \ 1 indicator
Flashes in green when the light source is preparing to turn on. Lights up in green when the TV is switched on.
Lights up in red when the TV is in standby mode. When the lamp door or the lamp itself is not securely attached, the
red indicator will continue to flash in intervals of three blinks at a time (see page 49).
8 Remote control sensor
Point the remote here.
9 1 (page 15)
Switches the TV on or off.
GB
10
Page 94
Projection Lamp
Your TV uses a projection lamp as its light source. As
with any lamp, it has lifespan and needs to be replaced
when the lamp indicator flashes or the screen becomes
darker.
Notes
After turning on your TV, it may take a while (1 minute or
less) before the picture appears.
When the projection lamp wears out, the screen goes dark.
Replace the lamp with a new Sony XL-2400 replacement
lamp (not supplied). How to replace the lamp, see page 48.
Warning
The light emitted from the lamp is quite bright when your TV
is in use. To avoid eye discomfort or injury, do not look into
the light housing when the power is on.
11
GB
Page 95
Getting Started
65.
65
KF-E50A10
min. 2.0 m
KF-E42A10
min. 1.8 m
1: Installing the TV
Recommended Viewing Area
Your viewing position may affect the picture quality.
For the best picture quality, install your TV within the
areas shown below.
ModelViewing distance
KF-E42A10min. 1.8 m
KF-E50A10min. 2.0 m
Horizontal Viewing Area
KF-E50A10
KF-E50A10
min. 2.0 m
min. 2.0 m
KF-E42A10
KF-E42A10
min. 1.8 m
min. 1.8 m
65
˚
65˚
65˚
65.
Vertical Viewing Area
KF-E50A10
min. 2.0 m
KF-E42A10
min. 1.8 m
Carrying Your TV
Carrying the TV requires at least two people. Do not
hold by the pedestal or the front panel of the TV.
Doing so may cause these parts to break off.
Do not grasp the
pedestal or the front
panel of the TV.
When moving the TV, place one hand in the hole on
the lower portion of the TV while grasping the top
with the other hand, as shown in the illustration below.
KF-E42A10
12
GB
30˚
KF-E50A10
30˚
If you have connected cables and cords, be sure to
unplug them before moving the TV.
Notes
• To ensure the safety of children and the TV, keep children
away from the TV during installation. Climbing on or
pushing the TV or its stand may cause it to fall and damage
the TV.
• When installing your TV against a wall, keep your TV at
least 10 cm away from the wall to provide proper
ventilation.
Page 96
Preventing the TV from Toppling Over
As a protective measure, secure the TV as follows.
Using the TV stand with support belts
Sony strongly recommends using the TV stand SURG11S (for KF-E42A10)/SU-RG11M (for KFE50A10) with a support belt designed for your TV.
2: Inserting batteries
into the remote
Getting Started
Note
When using the SU-RG11S for KF-E42A10 (not supplied)/
SU-RG11M for KF-E50A10 (not supplied) stand for your
TV, you must use the support belt.
Notes
• Observe the correct polarity when inserting batteries.
• Dispose of batteries in an environmentally friendly way.
Certain regions may regulate disposal of the battery.
Please consult your local authority.
• Do not use different types of batteries together or mix old
and new batteries.
• Handle the remote with care. Do not drop or step on it, or
spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, or
in a place subject to direct sunlight, or in a damp room.
13
GB
Page 97
3: Connecting an antenna/VCR
A
To 8 VHF/UHF
1
(antenna)
Or
Antenna cable (not supplied)
B
To 8 VHF/UHF
1
(antenna)
Antenna cable
(not supplied)
Rear of the TV
VIDEO IN
VIDEO OUT
To video and
audio outputs
l: Signal flow
To antenna
output
VCR
VIDEO
AUDIO
R L
Audio/Video cable
(not supplied)
To 1
2
(S video input)
S video cable
(not supplied)
To S video
output
2
To t1/3 (video input)
L (MONO) (audio input)
R (audio input)
Rear of the TV
1312
Y
PB/CB
P
R/CR
L
R
(
MONO
S
)
L
R
S
L
R
14
GB
Page 98
1 Connect your antenna with the antenna
cable (not supplied).
If connecting to an antenna only (A)
Connect the male plug to the
(antenna) jack on the rear of the TV.
Notes
• Note that one end of the cable has a male plug fitted
while the other end is fitted with a female jack.
• Do not connect the power cord until all other
connections are complete; otherwise, a minimal
current leakage through the antenna and/or other
terminals to the ground could occur.
If connecting to a VCR with an antenna (B)
Connect your antenna to the input jack on your
VCR.
Notes
• If you connect a monaural VCR, connect the yellow
• If you connect a VCR to the 8 VHF/UHF (antenna)
• If the S video cable is connected to this TV and the
t VIDEO (the yellow jack) and the black
plug to
plug to AUDIO-L (MONO) (the white jack).
jack, preset the signal output from the VCR to the
program number 0 on the TV.
VCR, the S video signal is automatically selected.
8 VHF/UHF
2 Connect your VCR.
Connect the output jack on your VCR to the input
jack on the rear of the TV.
4: Switching on the TV
1
WEGA GATE
PROG
2
1 Connect the AC power cord to the AC
power jack (220-240 V AC, 50/60 Hz).
2 Press 1 on the TV (front side).
When you switch on the TV for the first time, the
language menu appears on the screen, then go to
“5: Selecting the language” on page 16.
When the TV is in standby mode (+ 1 indicator on
the front of the TV is red), press TV +/1 on the
remote to switch on the TV.
Getting Started
15
GB
Page 99
5: Selecting the
6: Auto-programming
language
When you switch on the TV for the first time, the
language menu appears on the screen.
M/m/</,
the TV
After selecting the language, a message confirming
that the TV starts auto program appears on the screen.
You must tune the TV to receive channels (TV
broadcasts). Do the following to search and store all
available channels.
Press M/m/</, to select the language
displayed on the menu screens, then press
.
Initial Setup
Please select your language
English
Select:
Enter:
The message confirming that the TV starts auto
program appears on the screen, then go to “6: Autoprogramming the TV”.
GB
16
End:
WEGA GATE
Press to select “Yes”.
Initial Setup
Please connect cable / antenna
before starting auto program
Start auto program now?
Ye s
Select:
No
Confirm:
End:
WEGA GATE
m
Initial Setup
ProgramTV System
01
VHF Low
Press any key to cancel
Auto
End:
WEGA GATE
Page 100
The TV starts searching for all available channels.
This may take some time. Do not press any buttons on
the TV or remote until it is completed.
Once all available channels have been stored, the TV
returns to normal operation, displaying the channel
stored on channel number 1.
Tip
If you press any of the buttons during auto-programming,
auto-programming operation is canceled. To perform autoprogramming again, activate “Initial Reset” in the “Setup”
menu (page 40).
When a message appears for you to confirm the
antenna connections
No channels are found. Check all the antenna
connections and press to start auto-program again.
To change the order in which the channels
are stored on the TV
See page 37.
Getting Started
17
GB
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.