Sony KDL-32S2030 User Manual [ru]

LCD Digital Colour TV

2-670-908-44(1)

LCD Digital Colour TV

KDL-46S2000 KDL-40S2000 KDL-32S2000 KDL-32S2030 KDL-26S2020

KDL-46S2010 KDL-40S2010 KDL-32S2010 KDL-26S2000 KDL-26S2030

KDL-46S2030 KDL-40S2030 KDL-32S2020 KDL-26S2010

2-670-908-4

4(1)

KDL-46S2000 KDL-40S2000 KDL-32S2000 KDL-32S2030 KDL-26S2020

KDL-46S2010 KDL-40S2010 KDL-32S2010 KDL-26S2000 KDL-26S2030

Operating Instructions

Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.

Инструкция по эксплуатации

Перед включением телевизора прочтите раздел “Сведения по безопасности” этого руководства. Сохраняйте данное руководство для справок в будущем.

Instrukcja obsługi

Przed rozpoczęciem eksploatacji telewizora należy zapoznać się z treścią rozdziału „Informacje dotyczące bezpieczeństwa” niniejszej instrukcji. Zachować instrukcję do wykorzystania w przyszłości.

KDL-46S2030 KDL-40S2030 KDL-32S2020 KDL-26S2010

For useful information about Sony products

Для получения полезной информации о продукции Сони

Szczegółowe informacje o produktach Sony

Printed in Spain

Introduction

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.

Notice for Digital TV function

• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive a DVB-T signal where you live.

• Although this TV set follows DVB-T specifications, compatibility with future DVB-T digital terrestrial broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some countries.

Trademark information

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

• TruSurround XT, SRS and ( SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

• HDMI, the HDMI logo and

Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

• The illustrations used in this manual are of the KDL32S2000 unless otherwise state.

z) symbol are trademarks of

High-Definition Multimedia

Table of Contents

Start-up Guide 4

Safety information .....................................................................................................................7

Precautions .............................................................................................................................10

Overview of the remote ........................................................................................................11

Overview of the TV buttons and indicators ........................................................................12

Watching TV

Watching TV............................................................................................................................13

Checking the Digital Electronic Programme Guide (EPG) .............................................15

Using the Favourite list ..................................................................................................17

Viewing pictures from connected equipment ..........................................................................18

Using MENU Functions

Navigating through menus ......................................................................................................19

Picture menu ...........................................................................................................................20

Sound menu............................................................................................................................22

Screen menu...........................................................................................................................24

Set-up menu............................................................................................................................25

PC Settings menu ...................................................................................................................27

Analogue Set-up menu (Analogue mode only) .......................................................................28

Digital Set-up menu .......................................................................................................31

Using Optional Equipment

Connecting optional equipment...............................................................................................33

Additional Information

Specifications ..........................................................................................................................36

Troubleshooting ......................................................................................................................38

Index .......................................................................................................................................40

: for digital channels only

Start-up Guide

1: Checking the accessories

Remote RM-ED005 (1)

Size AA batteries (R6 type) (2)

Mains lead (Type C-6) (1)

Coaxial cable (1)

Cable holder (1)

Support belt (1) and screws (2)

2: Connecting an aerial/ VCR

Connecting an aerial only

Coaxial cable

(supplied)

Mains lead (supplied)

Connecting an aerial and VCR

To insert batteries into the remote

Notes

• Observe the correct polarity when inserting batteries.

• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of the battery. Please consult your local authority.

• Do not use different types of batteries together or mix old and new batteries.

• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, or in a place subject to direct sunlight, or in a damp room.

Mains lead (supplied)

RF lead

(not supplied)

Scart lead (not supplied)

VCR

3: Bundling the cables

5: Selecting the language and country/ region

Start-up Guide

4: Preventing the TV from toppling over

3,4 3,4

1 Connect the TV to your mains socket (220-

240V AC, 50Hz).

2 Press 1 on the TV (top side).

When you switch on the TV for the first time, the Language menu appears on the screen. When the TV is in standby mode (the indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

1 (standby)

Continued

3 Press F/f to select the language

displayed on the menu screens, then press

4 Press F/f to select the country/region in

which you will operate the TV, then press

1 Before you start auto-tuning the TV, insert

a pre-recorded tape into the VCR connected to the TV (page 4) and start play back.

The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, this procedure is not required. Go to step 2.

2 Select “OK”, then press .

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote.

If a message appears for you to confirm the aerial connections

No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again.

If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region. The message confirming the TV start auto-tuning appears on the screen, then go to “6: Auto-tuning the TV”.

6: Auto-tuning the TV

The TV will now search for and store all available TV channels.

3 When the Programme Sorting menu

appears on the screen, follow the steps of “Programme Sorting” (page 28).

If you do not wish to change the order in which the analogue channels are stored on the TV, go to step

4 Press MENU to exit.

The TV has now tuned in all the available channels.

Safety information

Mains lead

• Observe the followings to prevent the mains lead being damaged. If the mains lead is damaged, it may result in a fire or an electric shock. – Unplug the mains lead when moving the TV set. – When you disconnect the

mains lead, disconnect it from the mains socket first.

– Be sure to grasp the plug

when disconnecting the mains lead. Do not pull on the mains lead itself.

– Do not pinch, bend, or twist

the mains lead excessively. The core conductors may be exposed or broken.

– Do not modify the mains

lead. – Do not put anything heavy on the mains lead. – Keep the mains lead away from heat sources.

• If you damage the mains lead, stop using it and ask your dealer or Sony service centre to exchange it.

• Do not use the supplied mains lead on any other equipment.

• Use only an original Sony mains lead, not other brands.

Mains socket

• The TV set with a three-wire grounding type mains plug must be connected to a mains socket with a protective earthing connection.

• Do not use a poor fitting mains socket. Insert the plug fully into the mains socket. A poor fit may cause arcing and result in a fire. Contact your electrician to have the mains socket changed.

Cleaning the mains plug

Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire.

Overloading

This TV set is designed to operate on a 220–240 V AC supply only. Take care not to connect too many appliances to the same mains socket as this could result in fire or electric shock.

When not in use

• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.

• The TV set is not disconnected from the mains when the TV set is switched off. To disconnect the TV set completely, pull the plug from the mains. However, some TV sets may have features which need the TV set to be left in standby to work correctly.

Carrying

• Before carrying the TV set, disconnect all the cables from the TV set.

• Carrying the large size TV set requires two or more people.

• When you carry the TV set by hand, hold the TV set as illustrated on the right. When lifting the TV set or moving the panel of the TV set, hold it firmly from the bottom. If you do not do so, the TV set may fall and be damaged or cause serious injury.

• When transporting it, do not subject the TV set to jolts or excessive vibration. The TV set may fall and be damaged or cause serious injury.

• If the TV set has been dropped or damaged, have it checked immediately by qualified service personnel.

• When you carry the TV set in for repair or when you move it, pack it using the original carton and packing material.

Placement

• The TV set should be installed near an easily accessible mains socket.

• Place the TV set on a stable, level surface. Do not hang anything on the TV set. If you do, the TV set may fall from the stand, causing damage or serious injury.

• Do not install the TV set in places subject to extreme temperature, for example in direct sunlight, or near a radiator, or heating vent. If the TV set is exposed to extreme temperature, the TV set may overheat and cause deformation of the casing or cause the TV set to malfunction.

• Do not install the TV set in a place exposed to direct air conditioning. If the TV set is installed in such a location, moisture may condense inside and may cause a malfunction.

• Never place the TV set in hot, oily, humid or excessively dusty places.

• Do not install the TV set where insects may enter.

• Do not install the TV set where it may be exposed to mechanical vibration.

• Do not install the TV set in a location where it may protrude, such as on or behind a pillar, or where you might bump your head on it. Otherwise, it may result in injury.

• Do not allow children to climb on the TV set.

• If you use the TV set near the seashore, salt may corrode metal parts of the TV set and cause internal damage or fire.

Continued

Ventilation

• Never cover the ventilation holes or insert anything in the cabinet. It may cause overheating and result in a fire.

• Unless proper ventilation is provided, the TV set may gather dust and get dirty. For proper ventilation, observe the following: – Do not install the TV set turned backwards or sideways. – Do not install the TV set turned over or upside down. – Do not install the TV set on a shelf or in a closet. – Do not place the TV set on a rug or bed. – Do not cover the TV set with cloth, such as curtains, or

items such as newspapers, etc.

• Leave some space around the TV set as shown below. Otherwise, air-circulation may be inadequate and causing overheating, which may cause a fire or damage to the TV set.

Installed on the wall

30 cm

10 cm

Leave at least this space around the set.

Installed with stand

30 cm

6 cm

Leave at least this space around the set.

• Never install the TV set as follows:

Air circulation is blocked.

Wall Wall

10 cm10 cm

Air circulation is blocked.

Optional accessories

Observe the following when installing the TV set using a stand or wall-mount bracket. If you do not do so, the TV set may fall and cause serious injury.

• It is strongly recommended that you use Sony accessories for safety reasons: – KDL-46S2000/KDL-46S2010/KDL-46S2030/

KDL-40S2000/KDL-40S2010/KDL-40S2030:

Wall-mount bracket SU-WL51.

– KDL-32S2000/KDL-32S2010/KDL-32S2020/

KDL-32S2030/KDL-26S2000/KDL-26S2010/ KDL-26S2020/KDL-26S2030:

Wall-mount bracket SU-WL31.

• It is strongly recommended that you use the official Sony wall-mount bracket to allow adequate air circulation and to avoid accumulated dust on the TV.

• If the TV set is to be installed on a wall, have the installation carried out by qualified service personnel. Improper installation may render the TV set unsafe.

• Secure the TV set properly, following the instructions supplied with your stand when installing the TV set.

• Be sure to attach the brackets supplied with your stand.

Wiring

• When wiring cables, be sure to unplug the mains lead for your safety.

• Take care not to catch your feet on the cables. It may damage the TV set.

Medical institutions

Do not place this TV set in a place where medical equipment is in use. It may cause a malfunction of medical instruments.

Outdoor use

• Do not install this TV set outdoors. If the TV set is exposed to rain, it may result in a fire or an electrical shock.

• If this TV set is exposed to direct sunlight, the TV set may heat up and it may damage the TV set.

Vehicle, Ships and other vessels

• Do not install this TV set in a vehicle. The motion of the vehicle may cause the TV set to fall down and cause injury.

• Do not install this TV set on a ship or other vessel. If the TV set is exposed to seawater, it may cause a fire or damage the TV set.

Water and moisture

• Do not use this TV set near water – for example, near a bathtub or shower room. Also do not expose to rain, moisture or smoke. This may result in a fire or an electric shock.

• Do not touch the mains lead and the TV set with wet hands. Doing so may cause an electric shock or damage to the TV set.

Moisture and flammable objects

• Do not place any objects on the TV set. The TV set shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall be placed on the TV set.

• To prevent fire, keep flammable objects or naked lights (e.g. candles) away from the TV set.

• If any liquid or solid object does fall through openings in the cabinet, do not operate the TV set. It may result in an electric shock or damage to the TV set. Have it checked immediately by qualified service personnel.

Lightning storms

For your own safety, do not touch any part of the TV set, mains lead, or aerial lead during lightning storms.

Broken pieces

• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

Servicing

Dangerously high Voltage are present inside the TV set. Do not open the cabinet. Entrust the TV set to qualified service personnel only.

Small accessories removal and fittable

Keep small accessories out of children’s reach.

Precautions

Viewing the TV

• To view the TV comfortably, the recommended viewing position is from four to seven times the screen’s vertical length away from the TV set.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed down from the ceiling.

• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

Volume adjustment

• Adjust the volume so as not to trouble your neighbours. Sound carries very easily at night time. Therefore, closing the windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal and mercury. The fluorescent tube used in this TV set also contains mercury. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.

• Do not push on the screen, scratch it with a hard object, or throw anything at it. The screen may be damaged.

• Do not touch the display panel after operating the TV set continuously for a long period as the display panel becomes hot.

• We recommend that the screen surface be touched as little as possible.

• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl

materials may result in damage to the screen surface and cabinet material.

• The ventilation holes can accumulate dust over time. To ensure proper ventilation, we recommend removing the dust periodically (once a month) using a vacuum cleaner.

• If the angle of the TV set is to be adjusted, steady the base of the stand with your hand to prevent the TV set from becoming separated from the stand. Be careful not to get your fingers caught between the TV set and the stand.

Optional Equipments

• Do not install optional components too close to the TV set. Keep optional components at least 30 cm away from the TV set. If a VCR is installed in front of the TV set or beside the TV set, the picture may become distorted.

• Picture distortion and/or noisy sound may occur if the TV set is positioned in close proximity to any equipment emitting electromagnetic radiation.

Disposal of the TV set

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Overview of the remote

1 "/1 – TV standby

Switches the TV on and off from standby mode.

2 A/B – Dual Sound (page 23) 3 Coloured buttons

Selects the options at the bottom of the Favourite and EPG digital menus.

4 / – Info / Text reveal

• In digital mode: Displays brief details of the programme currently being watched.

• In analogue mode: Displays information such as current channel number and screen mode.

• In Text mode (page 14): Reveals hidden information (e.g., answers to a quiz).

5 F/f/G/g/ (page 13, 19) 6 TOOLS (page 14, 18, 35)

Enables you to access various viewing options and change/make adjustments according to the source and screen mode.

7 MENU (page 19) 8 DIGITAL – Digital mode (page 13) 9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the second digit within two seconds.

• In Text mode: Enters the three digit page number to select the page.

0 – Previous channel

Returns to the previous channel watched (for more than five seconds).

qa PROG +/- (page 13)

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode: Selects the next (+) or previous (-) page.

qs 2 +/- – Volume qd % – Mute (page 13)

/ – Text (page 14)

qf qg ANALOG – Analogue mode (page 13) qh / RETURN

Returns to the previous screen of any displayed menu.

qj – EPG (Digital Electronic Programme Guide) (page 15) qk – Picture freeze (page 14)

Freezes the TV picture.

ql – Screen mode (page 14) w; / – Input select / Text hold

• In TV mode (page 18): Selects the input source from equipment connected to the TV sockets.

• In Text mode (page 14): Holds the current page.

Tip

The A/B, PROG + and number 5 buttons have tactile dots. Use the tactile dots as references when operating the TV.

Overview of the TV buttons and indicators

1 (page 19) 2 / – Input select/OK

• In TV mode (page 18): Selects the input source from equipment connected to the TV sockets.

• In TV menu: Selects the menu or option, and confirm the setting.

3 2 +/-/ /

• Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options left ( ) or right ( ).

4 PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up ( ) or down ( ).

5 1 – Power

Switches the TV on or off.

6 Remote control sensor 7 – Picture Off/Timer indicator

• Lights up in green when the picture is switched off (page 26).

• Lights up in orange when the timer is set (page 25).

8 1 – Standby indicator

Lights up in red when the TV is in standby mode.

9 " – Power indicator

Lights up in green when the TV is switched on.

Note

Make sure that the TV is completely switched off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

Watching TV

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 15.

In digital mode

An information banner appears briefly. The following icons may be indicated on the banner.

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

: Current programme is being recorded

Additional operations

To Do this

Turn off the TV temporarily (Standby mode)

Turn on the TV from Standby mode without sound

Press "/1.

Press %. Press 2 +/- to set the volume level.

Watching TV

1 Press 1 on the TV (top side) to switch on

the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

Switch off the TV. Press 1 on the TV (top side).

Note

To disconnect the TV completely, pull the plug from the mains.

Adjust the volume Press 2 + (increase)/

- (decrease).

Mute the sound Press %. Press again to restore.

Access the Programme index table (in analogue mode only)

Press . To select an analogue channel, press

. To access the Input signal index table, see page 18.

F/f, then press

Continued

To access Text

Press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or PROG +/-. To hold a page, press / . To reveal hidden information, press / .

Tips

• Ensure that the TV is receiving a good signal, or some text errors may occur.

• Most TV channels broadcast a Text service. For information on the use of the service, select the index page.

• When four coloured items appear at the bottom of the Text page, Fastext is available. Fastext allows you to access pages quickly and easily. Press the corresponding coloured button to access the page.

Picture Freeze

Freezes the TV picture (e.g. to make a note of a telephone number or recipe).

1 Press on the remote control.

Wide

Displays wide screen (16:9) broadcasts in the correct proportions.

Zoom*

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

14:9*

Displays 14:9 broadcasts in the correct proportions. As a result, black border areas are visible on the screen.

2 Press F/f/G/g to adjust the position of the

window.

3 Press to remove the window. 4 Press again to return to normal TV

mode.

To change the screen mode manually to suit the broadcast

Press repeatedly to select Smart, 4:3, Wide, Zoom, or 14:9.

Smart*

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen.

4:3

Displays conventional 4:3 broadcasts (e.g., non-wide screen TV) in the correct proportions.

* Parts of the top and bottom of the picture may be cut off.

Tips

• Alternatively, you can set “Auto Format” to “On”. The TV will automatically select the best mode to suit the broadcast (page 24).

• You can adjust the position of the picture when selecting 14:9 or Zoom. Press read subtitles).

• Some characters and/or letters at the top and the bottom of the picture may not be visible in Smart mode. In such a case, you can select “Vertical Size” using the “Screen” menu and adjust vertical size to make it visible.

F/f to move up or down (e.g., to

Using the Tools menu

Press TOOLS to display the following options when viewing the TV programme.

Options Description

Power Saving See page 26.

Subtitle Setting (in digital mode only)

Digital Favourites (in digital mode only)

Picture Mode See page 20.

Sound Mode See page 22.

Auto Clock Set (in analogue mode only)

Sleep Timer See page 25.

See page 32.

See page 17.

Allows you to switch to digital mode and obtain the time.

i Volume See page 23.

Checking the Digital Electronic Programme Guide (EPG) *

1 In digital mode, press to display the

Digital Electronic Programme Guide (EPG).

2 Perform the desired operation, as shown in

the following table.

Note

Programme information will only be displayed if the TV

Digital Electronic Programme Guide (EPG)

* Please note that this function may not be available in some countries.

To Do this

Turn off the EPG Press .

station is transmitting it.

Watching TV

Move through the EPG Press

Watch a current programme Press while the current programme is selected.

Sort the programme information by category – Category list

Set a programme to be recorded – Timer REC

F/f/G/g.

1 Press the blue button. 2 Press

3 Press .

1 Press F/f/G/g to select the future programme you want to

2 Press . 3 Press 4 Press to set the TV and your VCR timers.

Notes

• You can set VCR timer recording on the TV only for Smartlink compatible VCRs. If your VCR is not Smartlink compatible, a message will be displayed to remind you to set your VCR timer.

• Once a recording has begun, you can switch the TV to standby mode, but do not switch off the TV completely or the recording may be cancelled.

• If an age restriction for programmes has been selected, a message asking for pin code will appear on the screen. For more details refer to “Parental Lock” on page 32.

F/f/G/g to select a category. The category name is

displayed on the side.

The categories available include: “All Categories”: Contains all available channels. “News”: Contains all news channels.

The Digital Electronic Programme Guide (EPG) now only displays the current programmes from the category selected.

record.

F/f to select “Timer REC”.

A symbol appears by that programme’s information. The indicator on the TV (front) lights up.

Continued

To Do this

Set a programme to be displayed automatically on the screen when it starts – Reminder

1 Press F/f/G/g to select the future programme you want to

display.

2 Press . 3 Press 4 Press to automatically display the selected programme

when the programme starts.

A c symbol appears by that programme’s information.

Note

If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.

F/f to select “Reminder”.

Set the time and date of a programme you want to record – Manual timer REC

Cancel a recording/reminder – Timer list

Tip

You can also display the Digital Electronic Programme Guide (EPG) by selecting “Digital EPG” in the “MENU” (page 19).

1 Press . 2 Press 3 Press 4 Set the start and stop time in the same way as in step 3. 5 Press

Notes

• You can set VCR timer recording on the TV only for Smartlink compatible VCRs. If your VCR is not Smartlink compatible, a message will be displayed to remind you to set your VCR timer.

• Once a recording has begun, you can switch the TV to standby mode, but do not switch off the TV completely or the recording may be cancelled.

• If an age restriction for programmes has been selected, a message asking for pin code will appear on the screen. For more details refer to “Parental Lock” on page 32.

1 Press . 2 Press 3 Press

4 Press g to select “Yes”, then press to confirm.

F/f to select “Manual timer REC”, then press . F/f to select the date, then press g.

F/f to select the programme, then press to set the

TV and your VCR timers.

A symbol appears by that programme’s information. The indicator on the TV (front) lights up.

F/f to select “Timer list”. F/f to select the programme you want to cancel, then

press .

A display appears to confirm that you want to cancel the programme.

Using the Favourite list *

The Favourite feature allows you to select programs from a list of up to 8 channels you specify. To display the Favourite list, see “Navigating through menus” (page 19).

Favourite list

* Please note that this function may not be available in some countries.

To Do this

Create your Favourite list for the first time A message appears asking if you want to add channels to the Favourite list

when you select “Digital Favourites” in the “MENU” for the first time.

1 Press to select “Yes”. 2 Press

3 Press .

Turn off the Favourite list Press RETURN.

Watch a channel Press while selecting a channel.

F/f to select the channel you want to add.

If you know the channel number, you can use the number buttons to directly select a channel.

Channels that are stored in the Favourite list are indicated by a symbol.

Watching TV

Add or remove channels in the Favourite list

Remove all channels from the Favourite list

1 Press the blue button.

Channels that are stored in the Favourite list are indicated by a symbol.

2 Press F/f to select the channel you want to add or remove.

If you know the channel number, you can use the number buttons to directly select a channel.

3 Press . 4 Press the blue button to return to the Favourite list.

1 Press the blue button. 2 Press the yellow button.

A display appears to confirm that you want to delete all channels from the Favourite list.

3 Press G to select “Yes”, then press to confirm.

Viewing pictures from connected equipment

Switch on the connected equipment, then perform one of the following operation.

For equipment connected to the scart sockets using a fully-wired 21-pin scart lead

Start playback on the connected equipment. The picture from the connected equipment appears on the screen.

For an auto-tuned VCR (page 6)

In analogue mode, press PROG +/-, or the number buttons, to select the video channel.

For other connected equipment

Press / repeatedly until the correct input symbol (see below) appears on the screen.

AV1/ AV1, AV2/ AV2: Audio/video or RGB input signal through the scart socket / 1 or 2. appears only if an RGB source has been connected.

AV3: Component input signal through the Y, P sockets / 3, and audio input signal through the L, R sockets / 3.

B/CB, PR/CR

Using the Tools menu

Press TOOLS to display the following options when viewing pictures from connected equipment other than PC.

Options Description

Power Saving See page 26.

Picture Mode See page 20.

Sound Mode See page 22.

Auto Clock Set (in analogue mode only)

Sleep Timer See page 25.

i Volume See page 23.

Allows you to switch to digital mode and obtain the time.

AV4: Digital audio/video signal is input through the HDMI IN 4 socket. Audio input signal is analogue only if the equipment has been connected using the DVI and audio out socket.

AV5/ AV5: Video input signal through the video socket 5, and audio input signal through the L (MONO), R audio sockets 5. appears only if the equipment is connected to the S video socket 5 instead of the video socket 5, and S video input signal is input through the S video socket 5.

Additional operations

To Do this

Return to the normal TV operation

Access the Input signal index table

Press DIGITAL or ANALOG.

Press to access the Input signal index table. (Then, only in analogue mode, press select an input source, press then press .

g.) To

F/f,

Using MENU Functions

Navigating through menus

“MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or external inputs with the remote. Also, settings for your TV can be changed easily using “MENU”.

1 Press MENU to display the menu.

2,3

2 Press F/f to select an option. 3 Press to confirm a selected option.

To exit the menu, press MENU.

Menu Description

Digital Favourites (only in areas with

digital broadcasting)

Launches the Favourite list. For details about settings, see page 17.

Using MENU Functions

Programme List (only in areas with

analogue broadcasting)

Analogue (only in areas with

digital broadcasting)

Digital (only in areas with

digital broadcasting)

Digital EPG (only in areas with

digital broadcasting)

External Inputs

Settings

Allows you to select TV programs from a list of channel labels.

• To watch the desired channel, select the channel, then press .

• To assign a label to a program, see page 28.

Returns to the last viewed analogue channel.

Returns to the last viewed digital channel.

Launches the Digital Electronic Programme Guide (EPG). For details about settings, see page 15.

Selects equipment connected to your TV.

• To watch the desired external input, select the input source, then press .

• To assign a label to an external input, see page 25.

Opens the Settings menu screen where most of advanced settings and adjustments are performed. Select a menu icon, select an option and make the desired change or adjustment using For details about settings, see page 20 to 32.

F/f/G/g.

Picture menu

You can select the options listed below on the Picture menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Target Inputs

Picture Mode

Reset

Backlight

Contrast

Brightness

Colour

Hue

Selects whether to apply settings made in the Picture menu to all inputs, or only to the input currently being watched. “All”: Applies settings to all inputs. “Viewing Only”: Applies settings only to the current input.

Selects the picture mode. “Vivid”: For enhanced picture contrast and sharpness. “Standard”: For standard picture. Recommended for home entertainment. “Custom”: Allows you to store your preferred settings.

Resets all picture settings except “Picture Mode” to the factory settings.

Adjusts the brightness of the backlight.

Increases or decreases picture contrast.

Brightens or darkens the picture.

Increases or decreases colour intensity.

Increases or decreases the green tones.

Tip

“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).

Colour Temperature

Sharpness

Adjusts the whiteness of the picture. “Cool”: Gives the white colours a blue tint. “Neutral”: Gives the white colours a neutral tint. “Warm1”/“Warm2”: Gives the white colours a red tint. “Warm2” gives a redder tint than “Warm1”.

Tip

“Warm1” and “Warm2” can only be selected when you set “Picture Mode” to “Custom”.

Sharpens or softens the picture.

Noise Reduction

Reduces the picture noise (snowy picture) in a weak broadcast signal. “Auto”: Automatically reduces the picture noise. “High”/“Medium”/“Low”: Modifies the effect of the noise reduction. “Off”: Turns off the Noise Reduction feature.

Advanced Settings

Customizes the Picture function in more detail. When you set “Picture Mode” to “Custom”, you can set/change these settings. “Reset”: Resets all the advanced video settings to the factory settings. “Black Corrector”: Enhances black areas of the picture for stronger contrast. “Contrast Enhancer”: Automatically adjusts “Contrast” to the most suitable settings judging from the brightness of the screen. This setting is especially effective for dark images, increasing vibrancy in the picture. “Gamma”: Adjusts the balance between bright and dark areas of the picture. “Clear White”: Emphasizes white colours. “Live Colour”: Makes colours more vivid. “MPEG Noise Reduction”: Reduces the picture noise in MPEG-compressed video (in digital mode only).

Using MENU Functions

Sound menu

You can select the options listed below on the Sound menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Target Inputs

Sound Mode

Reset

Treble

Bass

Balance

Auto Volume

Surround

Selects whether to apply settings made in the Sound menu to all inputs, or only to the input currently being watched. “All”: Applies settings to all inputs. “Viewing Only”: Applies settings only to the current input.

Selects the sound mode. “Dynamic”: Enhances treble and bass. “Standard”: For standard sound. Recommended for home entertainment. “Custom”: Flat response. Also allows you to store your preferred settings.

Resets the sound settings except “Sound Mode”, “Dual Sound”, “i Speaker Link” and “i Volume” to the factory settings.

Adjusts higher-pitched sounds.

Adjusts lower-pitched sounds.

Emphasizes left or right speaker balance.

Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend to be louder than programmes).

Selects the surround mode. “TruSurround XT”: For surround sound (for stereo programmes only). “Simulated Stereo”: Adds a surround-like effect to mono programs. “Off”: For normal stereo or mono reception.

BBE

Gives sound more impact by compensating for phase effects in speakers using the “BBE High Definition Sound System”.

Dual Sound

Selects the sound from the speaker for a stereo or bilingual broadcast. “Stereo”, “Mono”: For a stereo broadcast. “A”/“B”/“Mono”: For a bilingual broadcast, select “A” for sound channel 1, “B” for sound channel 2, or “Mono” for a mono channel, if available.

Tip

If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “A” or “B”.

i Speaker Link

Switches on/off the TV’s internal speakers when headphones are connected.

(headphone speaker link)

i Volume

Adjusts the volume of the headphones.

(headphone volume)

Tip

“Treble”, “Bass”, “Balance”, “Auto Volume”, “Surround” and “BBE” cannot be used for headphones and audio output sockets.

Using MENU Functions

Screen menu

You can select the options listed below on the Screen menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Target Inputs

Screen Format

Auto Format

4:3 Default

Display Area

Selects whether to apply settings made in the Screen menu to all inputs, or only to the input currently being watched. “All”: Applies settings to all inputs. “Viewing Only”: Applies settings only to the current input.

For details about the screen format, see “To change the screen mode manually to suit the broadcast” (page 14).

Automatically changes the screen format according to the broadcast signal. To keep your setting, select “Off”.

Tips

• Even if you have selected “On” or “Off” in “Auto Format”, you can always modify the format of the screen by pressing repeatedly.

• “Auto Format” is available for PAL and SECAM signals only.

Selects the default screen mode for use with 4:3 broadcasts. “Smart”: Displays conventional 4:3 broadcasts with an imitation wide screen effect. “4:3”: Displays conventional 4:3 broadcasts in the correct proportions. “Off”: Keeps the current “Screen Format” setting when the channel or input is changed.

Tip

This option is available only if “Auto Format” is set to “On”.

Adjusts the screen area displaying the picture. “Normal”: Displays the picture in the original size. “–1”/“–2”: Enlarges the picture to hide the edge of the picture.

Horizontal Shift

Vertical Shift

Vertical Size

Adjusts the horizontal position of the picture for each screen format.

Adjusts the vertical position of the picture when the screen format is set to Zoom or 14:9.

Adjusts the vertical size of the picture when the screen format is set to Smart, Zoom or 14:9.

Set-up menu

You can select the options listed below on the Set-up menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Using MENU Functions

Auto Start-up

Language

AV Preset

Auto S Video

Timer Settings

Starts the “first time operation menu” to select the language and country/region, and tune in all available digital and analogue channels. Usually, you do not need to do this operation because the language and country/region will have been selected and channels already tuned when the TV was first installed (page 5, 6). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).

Selects the language in which the menus are displayed.

Assigns a name to any equipment connected to the side and rear sockets. The name will be displayed briefly on the screen when the equipment is selected. You can skip an input source that is not connected to any equipment.

1 Press 2 Press

Selects the input signal from S video sockets 5 when / 5 sockets are both

connected.

Sets the timer to turn on/off the TV.

Sleep Timer

Sets a period of time after which the TV automatically switches itself into standby mode. When the Sleep Timer is activated, the (Timer) indicator on the TV (front) lights up in orange.

Tips

• If you switch off the TV and switch it on again, “Sleep Timer” is reset to “Off”.

• “TV will soon turn off by sleep timer.” appears on the screen one minute before the TV switches to standby mode.

F/f to select the desired input source, then press . F/f to select the desired option below, then press .

Equipment labels: Uses one of the preset labels to assign a name to connected equipment. “Edit”: Creates your own label. Follow steps 2 to 4 of “Programme Labels” (page 28). “Skip”: Skips an input source that is not connected to any equipment when you press

to select the input source.

Continued

On Timer

Sets the timer to turn on the TV. “Day”: Selects the day on which you want to activate the On Timer. “Time”: Sets the time to turn on the TV. “Duration”: Selects the time period after which the TV automatically switches to standby mode again. “Volume Set-up”: Sets the volume for when the timer turns on the TV.

Clock Set

Allows you to adjust the clock manually. When the TV is receiving digital channels, the clock cannot be adjusted manually since it is set to the time code of the broadcasted signal.

Power Saving

Light Sensor

AV2 Output

Quiet Power On

Speaker

Colour System

Selects the power saving mode to reduce the power consumption of the TV. When “Picture Off” is selected, the picture is switched off and the (Picture Off) indicator on the TV (front) lights up in green. The sound remains unchanged.

Automatically optimizes the picture settings according to the ambient light in the room.

Sets a signal to be output through the socket labelled / 2 on the rear of the TV. If you connect a VCR or other recording equipment to the / 2 socket, you can then record from the equipment connected to other sockets of the TV. “TV”: Outputs a broadcast. “AV1”: Outputs signals from equipment connected to the / 1 socket. “AV5”: Outputs signals from equipment connected to the / 5 socket. “Auto”: Outputs whatever is being viewed on the screen (except signals from the

/ 3 and HDMI IN 4 sockets).

Sets the volume control at a low level when the TV is first turned on, gradually increasing the sound to a preset level.

Switches on/off the TV’s internal speakers. “On”: The TV speakers are turned on in order to listen to the TV’s sound through TV’s speakers. “Off”: The TV speakers are turned off in order to listen to the TV’s sound only through your external audio equipment connected to the audio output sockets.

Selects the colour system (“Auto”, “PAL”, “SECAM”, “NTSC3.58”, “NTSC4.43”, or “PAL60”) according to the input signal from the input source.

Information

All Reset

Displays your TV’s system information.

Resets all the Set-up settings to the factory settings and then launches the Auto Startup screen.

PC Settings menu

You can select the options listed below on the PC Settings menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Using MENU Functions

Screen Format

Reset

Auto Adjustment

Phase

Pitch

Horizontal Shift

Vertical Shift

Power Management

Selects a screen mode for displaying input from your PC. “Normal”: Displays the picture in its original size. “Full1”: Enlarges the picture to fill the display area, keeping its original horizontalto-vertical aspect ratio. “Full2”: Enlarges the picture to fill the display area.

Resets the PC settings except “Screen Format” and “Power Management” to the factory settings.

Automatically adjusts the display position and phase of the picture when the TV receives an input signal from the connected PC.

Tip

Auto Adjustment may not work well with certain input signals. In such cases, manually adjust “Phase”, “Pitch”, “Horizontal Shift” and “Vertical Shift”.

Adjusts the phase when the screen flickers.

Adjusts the pitch when the picture has unwanted vertical stripes.

Adjusts the horizontal position of the picture for each screen format.

Adjusts the vertical position of the picture for each screen format.

Switches the TV to standby mode if no signal is received for 30 seconds.

Analogue Set-up menu (Analogue mode only)

You can change/set the analogue settings using the Analogue Set-up menu. To select options in “Settings”, see “Navigating through menus” (page 19).

1 Digit Direct

Auto Tuning

Programme Sorting

Programme Labels

When “1 Digit Direct” is set to “On”, you can select an analogue channel using one preset number button (0 - 9) on the remote.

Note

When “1 Digit Direct” is set to “On”, you cannot select channel numbers 10 and above entering two digits using the remote.

Tunes in all the available analogue channels. Usually you do not need to do this operation because the channels are already tuned when the TV was first installed (page 5, 6). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).

Changes the order in which the analogue channels are stored on the TV.

1 Press

2 Press

Assigns a channel name of your choice up to five letters or numbers. The name will be displayed briefly on the screen when the channel is selected. (Names for channels are usually taken automatically from Text (if available).)

1 Press 2 Press

3 Repeat the procedure in step 2 until the name is complete. 4 Select “OK”, then press .

F/f to select the channel you want to move to a new position,

then press .

F/f to select the new position for your channel, then press .

F/f to select the channel you want to name, then press . F/f to select the desired letter or number (“_” for a blank space),

then press

If you input a wrong character

Press G/g to select the wrong character. Then, press F/f to select the correct character.

To delete all the characters

Select “Reset”, then press .

Manual Programme Preset

Before selecting “Label”/“AFT”/“Audio Filter”/“Skip”/“Decoder”, press PROG +/to select the programme number with the channel. You cannot select a programme number that is set to skip (page 30).

Programme

Presets programme channels manually.

1 Press 2 Press

3 Press 4 Press

5 Press F/f to select “Channel”, then press . 6 Press

7 Tune the channels as follows:

8 Press to jump to “Confirm”, then press . 9 Press

Repeat the procedure above to preset other channels manually.

Label

Assigns a name of your choice, up to five letters or numbers, to the selected channel. This name will be displayed briefly on the screen when the channel is selected. To input characters, follow steps 2 to 4 of “Programme Labels” (page 28).

AFT

Allows you to fine-tune the selected programme number manually if you feel that a slight tuning adjustment will improve the picture quality. You can adjust the fine tuning over a range of -15 to +15. When “On” is selected, the fine tuning is performed automatically.

Audio Filter

Improves the sound for individual channels in the case of distortion in mono broadcasts. Sometimes a non-standard broadcast signal can cause sound distortion or intermittent sound muting when watching mono programmes. If you do not experience any sound distortion, we recommend that you leave this option set to the factory setting “Off”.

Notes

• You cannot receive stereo or dual sound when “Low” or “High” is selected.

• “Audio Filter” is not available when “System” is set to “L”.

/System/Channel

F/f to select “Programme”, then press . F/f to select the programme number you want to manually tune

(if tuning a VCR, select channel 00), then press RETURN.

F/f to select “System”, then press . F/f to select one of the following TV broadcast systems, then

press

B/G: For western European countries/regions D/K: For eastern European countries/regions L: For France I: For the United Kingdom

F/f to select “S” (for cable channels) or “C” (for terrestrial

channels), then press

If you do not know the channel number (frequency)

Press F/f to search for the next available channel. When a channel has been found, the search will stop. To continue searching, press

If you know the channel number (frequency)

Press the number buttons to enter the channel number of the broadcast you want or your VCR channel number.

F/f.

f to select “OK”, then press .

Using MENU Functions

Continued

Skip

Skips unused analogue channels when you press PROG +/- to select channels. (You can still select a skipped channel using the number buttons.)

Decoder

Views and records the scrambled channel selected when using a decoder connected directly to scart connector / 1, or to scart connector / 2 via a VCR.

Note

Depending on the country/region selected for “Country” (page 6), this option may not be available.

Confirm

Saves changes made to the “Manual Programme Preset” settings.

+ 99 hidden pages