Sony KDL-32P3550, KDL-32P3600, KDL-32S5550, KDL-40S5650, KDL-40P5650 Operating Instructions
...
Award to goods or services which meet the environmental
requirements of the EU ecolabelling scheme
ES-CAT/022/002
At Sony we are constantly rethinking and redesigning in order to create innovative digital
entertainment products. And we are also constantly rethinking and re-evaluating our
products, processes and our potential impact on the planet.
Thanks to our results in that direction, this product achieved the European Eco label
award issued by the European Comission. You can get more information in following link:
http://europa.eu.int/comm/environment/ecolabel
Sony gives a minimum of 2 years guarantee for this LCD TV and 7 years availability for
replacement of electronic parts.
LCD Digital Colour TV
Operating Instructions
Instructions about “Installing Wall Mount Bracket” are included within
this TV’s instructions manual
For useful information about Sony products
Printed in Spain
415978812
4-159-788-12(1)
U
KDL-40P3600
KDL-40P5650
KDL-40S5650
KDL-37P3600
KDL-37P5650
KDL-37S5650
KDL-32P3550
KDL-32P3600
KDL-32P5550
KDL-32P5650
KDL-32S5550
KDL-32S5650
KDL-26P5550
KDL-26S5550
U
© 2009 Sony Corporation 4-159-788-12(1)
NOTICE FOR
CUSTOMERS IN THE
UNITED KINGDOM
Ŗ 6JKU68UGVEQORNKGUYKVJ&8$6CPF&8$%
specifications, but compatibKNKV[YKVJHWVWTG&8$6
FKIKVCNVGTTGUVTKCNCPF&8$%digital cable broadcasts are
not guaranteed.
Ŗ 5QOG&KIKVCN68HWPEVKQPUOC[PQVDGCXCKNCDNGKPUQOG
EQWPVTKGUCTGCUCPF&8$%ECDNGOC[PQVQRGTCVG
correctly with some providers.
A moulded plug complying with BS1363 is fitted to this
equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced
with the same rating of fuse approved by ASTA or BSI to
BS 1362 (i.e., marked with or ) must be used.
When an alternative type of plug is used it should be fitted
with the same rating of fuse, otherwise the circuit should be
protected by a 10 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable
fuse cover, be sure to attach the fuse cover after you change
the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest
Sony service station.
FUSE
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and
replace the fuse.
Please refer to the illustration that actually equipped with
the product.
For a list of compatible cable providers, refer to the support
web site:
JVVRUWRRQTVUQP[GWTQRGEQO68&8$%
~
Ŗ &8$%ECDNGPQVCXCKNCDNGHQT-&.2ZZ
The manufacturer of this product is Sony
%QTRQTCVKQP-QPCP/KPCVQMW6QM[Q
,CRCP6JG#WVJQTK\GF4GRTGUGPVCVKXGHQT'/%
CPFRTQFWEVUCHGV[KU5QP[&GWVUEJNCPF)OD*
*GFGNHKPIGT5VTCUUG5VWVVICTV)GTOCP[
For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
Trademark information
Ŗ KUCTGIKUVGTGFVTCFGOCTMQHVJG&8$2TQLGEV
Ŗ *&/+VJG*&/+NQIQCPF*KIJ&GHKPKVKQP/WNVKOGFKC
Interface are trademarks or registered trademarks of
*&/+.KEGPUKPI..%
Ŗ /CPWHCEVWTGFWPFGTNKEGPUGHTQO&QND[.CDQTCVQTKGU
&QND[CPFVJGFQWDNG&U[ODQNCTGVTCFGOCTMUQH
&QND[.CDQTCVQTKGU
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual
thoroughly and retain it for future reference.
Notice for Digital TV function
Ŗ #P[HWPEVKQPUTGNCVGFVQ&KIKVCN68 YKNNQPN[
YQTMKPEQWPVTKGUQTCTGCUYJGTG&8$6/2')CPF
*/2')#8%FKIKVCNterrestrial signals are
broadcast or where you have access to a compatible
&8$%/2')CPF*/2')#8%ECDNG
service. Please confirm with your local dealer if you can
TGEGKXGC&8$6UKIPCNYJGTGyou live or ask your cable
RTQXKFGTKHVJGKT&8$%ECDle service is suitable for
integrated operation with this TV.
Ŗ ;QWTECDNGRTQXKFGTOC[EJCTge a fee for their services,
or require you to agree to its terms and conditions of
business.
GB
2
About the model name in this manual
6JGőZZŒVJCVCRRGCTUQPVJe model name, corresponds to
two numeric digits related to design or colour variation.
~
Ŗ 6JGKNNWUVTCVKQPUWUGFKPVJKUOCPWCNCTGQHVJG-&.
40P5650 unless otherwise stated.
Table of Contents
Start-up Guide 4
Safety information.............. ... ... .... ... ... ... ....................................... ... .... ... ... ... .... ... ..............9
Precautions......................................................................................................................10
Overview of the remote ..................................................................................................11
Overview of the TV buttons and indicators..................................................................12
Watching TV
Watching TV ....................................................................................................................13
Using the Digital Electronic Programme Guide (EPG) .......................................15
Using the Digital Favourite list .................................... ... ... ... .... ... ... ... .... ...............16
Using Optional Equipment
Connecting optional equipment ....................................................................................17
Viewing pictures from connected equipment ..............................................................18
Playing Back Photo/Music via USB...............................................................................19
Using control for HDMI.................................................................................... ... ... ... ... ...19
Using MENU Functions
Navigating through menus.............................................................................................21
Settings............................................................................................................................22
Additional Information
Installing the Accessories (Wall-Mount Bracket).........................................................30
Specifications..................................................................................................................33
Troubleshooting..............................................................................................................35
: for digital channels only
Before operating the TV, please read “Safety Information” 9. Retain this manual for future reference.
GB
3
Start-up Guide
Push and slide to open.
1: Checking the
accessories
Remote RM-ED017 (1)
Mains lead (Type C-6) (1) (except for 37/32/26
inches)
Size AA batteries (R6 type) (2)
Stand (1)
Screws for stand (4)
To insert batteries into the remote
~
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix
old and new batteries.
• Dispose of batteries in an environmentally friendly way.
Certain regions may regulate disposal of batteries.
Please consult your local authority.
• Handle the remote with care. Do not drop or step on it,
or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source,
a place subject to direct sunlight, or a damp room.
2: Attaching the stand
Follow the assembling steps required to place on a
TV stand.
1 Open the carton box and take out the
stand and the screws.
2 Place the TV set on the stand. Take care
not to interfere with cables.
3 Fix the TV to the stand according to the
arrow marks that guide the screw
holes using the supplied screws.
GB
4
~
• If using an electric screwdriver, set the tightening torque
at approximately 1.5 N·m (15 kgf·cm).
3: Connecting an
AV1 AV2
Coaxial cable
Connecting an aerial/cable* only
Connecting an aerial/cable*/VCR/DVD recorder with
SCART
Scart lead
VCR/DVD recorder
Coaxial cable
Coaxial cable
Terrestrial signal
or cable
*
Terrestrial
signal or
cable
*
Connecting an aerial/cable*/VCR/DVD recorder with
HDMI
HDMI cable
Coaxial cable
Coaxial
cable
VCR/DVD recorder
Terrestrial signal
or cable
*
aerial/cable*/VCR/
DVD recorder
* Except for KDL-40/37/32P36xx.
~
• This product has been tested and found to compliant
with the limits set out in the EMC Directive for using
connection cables not longer than 3 meters (9.8 feet).
Start-up Guide
~
• AV1 outputs available only for analogue TV.
• AV2 outputs to the current screen (except PC, HDMI,
Component).
4: Preventing the TV
from toppling over
3
2
1 Install a wood screw (4 mm in diameter,
not supplied) in the TV stand.
1
Continued
5
GB
2 Install a machine screw (M4 × 20, not
RETURN TOOLS
GUIDE
MENU
AUDIOSCENE
ANALOGDIGITAL
Select: Confirm:
Language
Country
Location
Auto Start-up
supplied) into the screw hole of the TV.
3 Tie the wood screw and the machine
screw with a strong cord.
z
• An optional Sony support belt kit is used to secure the TV.
Contact your nearest Sony Service Centre to purchase a
kit. Have your TV model name ready for reference.
5: Bundling the cables
You can bundle the connecting cables as illustrated below.
~
• Do not bundle the mains lead with other connecting cables.
6:
Selecting the
language, country/region
and location
3,4,5
6
GB
1 Connect the TV to your mains socket
(220-240V AC, 50Hz).
2 Press 1 on the side of the TV.
When you turn on the TV for the first time, the
Language menu appears on the screen.
~
• When you turn on the TV, the power indicator light
up in green.
3 Press F/f to select the language
displayed on the menu screens, then
press
.
4 Press F/f to select the country/region in
Select:Back: Confirm:
Language
Country
Location
-
United Kingdom
Ireland
Nederland
België/Belgique
Luxembourg
France
Italia
Auto Start-up
Language
Country
Location
Home
Shop
Select:Back: Confirm:
Auto Start-up
which you will operate the TV, then press
.
7: Auto-tuning the TV
1 Press .
Auto Tuning
Do you want to start Auto Tuning?
Start-up Guide
If the country/region which you want to use on
the TV does not appear in the list, select “-”
instead of a country/region.
5 Press F/f to select the location type in
which you will operate the TV, then
press .
In Shop mode, some settings will be periodically
reset for Shop usage.
This option selects the initial picture mode
appropriate for the typical lighting condition in
these environments.
Back: Start:
2 Press F/f to select “Antenna” or
*”, then press .
“Cable
If you select “Cable*”, the screen for selecting
the scan type appears. See “To tune the TV for
Cable connection” (page 8).
The TV starts searching for all available digital
channels, followed by all available analogue
channels. This may take some time, so do not
press any buttons on the TV or remote while
proceeding.
If a message appears for you to confirm the
aerial connection
No digital or analogue channels were found.
Check all the aerial/cable* connections and
press to start auto-tuning again.
* Except for KDL-40/37/32P36xx.
3 When the Programme Sorting menu
appears on the screen, follow the steps of
“Programme Sorting” (page 25).
If you do not change the order in which the
analogue channels are stored on the TV, press
MENU to go to next step.
~
• This step will not appear if any analogue channel is
found.
Continued
GB
7
4 When the Eco Preset menu appears on
the screen, press
“No”, then press . If you press “Yes”,
the “Eco” settings are changed to
recommended values to reduce power
consumption.
Do you want to use the Eco Preset?
Choosing "YES" will reduce power consumption.
G/g to select “Yes” or
Eco Preset
Detaching the TableTop Stand from the TV
~
• Do not remove the Table-Top Stand for any reason other
than to wall-mount the TV.
Power Saving
Idle TV Standby
PC Power Management
Yes
The TV has now tuned in all the available
channels.
Reduce
3 h
On
No
To tune the TV for Cable connection
(Except for KDL-40/37/32P36xx)
1 Press .
2 Press F/f to select “Quick Scan” or “Full
Scan”, then press .
"Quick Scan" : channels are tuned according to
the cable operator information within the
broadcast signal.
Recommended setting for "Frequency",
"Network ID" and "Symbol Rate" is "Auto".
This option is recommended for fast tuning
when supported by your cable operator.
If the "Quick Scan" does not tune, please use the
"Full Scan" method below.
"Full Scan" : All available channels are tuned
and stored. This procedure may take some time.
This option is recommended when "Quick Scan"
is not supported by your cable provider.
For further information about supported cable
providers, refer to support web site:
http://support.sony-europe.com/TV/DVBC
3 Press G/g/f to select “Start”.
The TV starts searching for channels. Do not
press any buttons on the TV or remote.
~
• Some cable providers do not support “Quick Scan”. If no
channels are detected using “Quick Scan”, perform “Full
Scan”.
Table-Top
Stand
GB
8
Safety
Mounting Hook
Hook attachment on rear
of TV set
Screw (supplied with the
Wall-mount bracket)
8 mm - 12 mm
30 cm
10 cm 10 cm
10 cm
Leave at least this space around
the set.
30 cm
10 cm
10 cm
6 cm
Leave at least this space around
the set.
Wall Wall
Information
Installation/Set-up
Install and use the TV set in accordance
with the instructions below in order to
avoid any risk of fire, electrical shock or
damage and/or injuries.
Installation
• The TV set should be installed near an
easily accessible mains socket.
• Place the TV set on a stable, level
surface.
• Only qualified service personnel should
carry out wall installations.
• For safety reasons, it is strongly
recommended that you use Sony
accessories, including:
– Wall-mount bracket SU-WL500
(KDL-40P36/P56/S56xx, KDL37P36/P56/S56xx, KDL-32P35/
P36/P55/P56/S55/S56xx)
– Wall-mount bracket SU-WL100
(KDL-26P55/S55xx)
• Be sure to use the screws supplied with
the Wall-mount bracket when attaching
the mounting hooks to the TV set. The
supplied screws are designed so that they
are 8 mm to 12 mm in length when
measured from the attaching surface of
the mounting hook.
The diameter and length of the screws
differ depending on the Wall-mount
bracket model.
Use of screws other than those supplied
may result in internal damage to the TV
set or cause it to fall, etc.
Transporting
•Before
transporting the
TV set, disconnect
all cables.
• Two or three
people are needed
to transport a large
TV set.
• When
transporting the
TV set by hand,
hold it as shown
on the right. Do
not put stress on
the LCD panel.
• When lifting or
moving the TV
set, hold it firmly
from the bottom.
• When transporting the TV set, do not
subject it to jolts or excessive vibration.
• When transporting the TV set for repairs
Ventilation
• Never cover the ventilation holes or
or when moving, pack it using the
original carton and packing material.
insert anything in the cabinet.
• Leave space around the TV set as shown
below.
• It is strongly recommended that you use
a Sony wall-mount bracket in order to
provide adequate air-circulation.
Installed on the wall
Installed with stand
• To ensure proper ventilation and prevent
the collection of dirt or dust:
– Do not lay the TV set flat, install
upside down, backwards, or
sideways.
– Do not place the TV set on a shelf,
rug, bed or in a closet.
– Do not cover the TV set with a cloth,
such as curtains, or items such as
newspapers, etc.
– Do not install the TV set as shown
below.
Air circulation is blocked.
Mains lead
Handle the mains lead and socket as
follows in order to avoid any risk of fire,
electrical shock or damage and/or injuries:
– Use only mains leads supplied by
Sony, not other suppliers.
– Insert the plug fully into the mains
socket.
– Operate the TV set on a 220–240 V A C
supply only.
– When wiring cables, be sure to unplug
the mains lead for your safety and take
care not to catch your feet on the
cables.
– Disconnect the mains lead from the
mains socket before working on or
moving the TV set.
– Keep the mains lead away from heat
sources.
– Unplug the mains plug and clean it
regularly. If the plug is covered with
dust and it picks up moisture, its
insulation may deteriorate, which
could result in a fire.
Notes
• Do not use the supplied mains lead on
any other equipment.
• Do not pinch, bend, or twist the mains
lead excessively. The core conductors
may be exposed or broken.
• Do not modify the mains lead.
• Do not put anything heavy on the mains
lead.
• Do not pull on the m ains lead itself when
disconnecting the mains lead.
• Do not connect too many appliances to
the same mains socket.
• Do not use a poor fitting mains socket.
Prohibited Usage
Do not install/use the TV set in locations,
environments or situations such as those
listed below, or the TV set may
malfunction and cause a fire, electrical
shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the
seashore, on a ship or other vessel, inside a
vehicle, in medical institutions, unstable
locations, near water, rain, moisture or
smoke.
Environment:
• To prevent the spread of fire,
keep candles or other open
flames away from this
product at all time.
• Places that are hot, humid, or
excessively dusty; where insects may
enter; where it might be exposed to
mechanical vibration, near flammable
objects (candles, etc). The TV set shall
not be exposed to dripping or splashing
and no objects filled with liquids, such
as vases, shall be placed on the TV.
Situation:
Do not use when your hands are wet, with
the cabinet removed, or with attachments
not recommended by the manufacturer.
Disconnect the TV set from mains socket
and aerial during lightning storms.
Broken pieces:
• Do not throw anything at the TV set. The
screen glass may break by the impact and
cause serious injury.
• If the surface of the TV set cracks, do not
touch it until you have unplugged the
mains lead. Otherwise electric shock
may result.
When not in use
• If you will not be using the TV set for
several days, the TV set should be
disconnected from the mains for
environmental and safety reasons.
• As the TV set is not disconnected from
the mains when the TV set is just turned
off, pull the plug from the mains to
disconnect the TV set completely.
• However, some TV sets may have
features that require the TV set to be left
in standby to work correctly.
Continued
GB
9
For children
• Do not allow children t o climb on the TV
set.
• Keep small accessories out of the reach
of children, so that they are not
mistakenly swallowed.
If the following problems
occur...
Turn off the TV set and unplug the mains
lead immediately if any of the following
problems occur.
Ask your dealer or Sony service centre to
have it checked by qualified service
personnel.
When:
– Mains lead is damaged.
– Poor fitting of mains socket.
– TV set is damaged by being dropped,
hit or having something thrown at it.
– Any liquid or solid object falls through
openings in the cabinet.
Precautions
Viewing the TV
• View the TV in moderate light, as
viewing the TV in poor light or during
long period of time, strains your eyes.
• When using headphones, adjust the
volume so as to avoid excessive levels,
as hearing damage may result.
LCD Screen
• Although the LCD screen is made with
high-precision technology and 99.99%
or more of the pixels are effective, black
dots may appear or bright points of light
(red, blue, or green) may appear
constantly on the LCD screen. This is a
structural property of the LCD screen
and is not a malfunction.
• Do not push or scratch the front filter, or
place objects on top of this TV set. The
image may be uneven or the LCD screen
may be damaged.
• If this TV set is used in a cold place, a
smear may occur in the picture or the
picture may become dark. This does not
indicate a failure. These phenomena
disappear as the temperature rises.
• Ghosting may occur when still pictures
are displayed continuously. It may
disappear after a few moments.
• The screen and cabinet get warm when
this TV set is in use. This is not a
malfunction.
• The LCD screen contains a small amount
of liquid crystal. Some fluorescent tubes
used in this TV set also contain mercury.
Follow your local ordinances and
regulations for disposal.
Handling and cleaning the
screen surface/cabinet of
the TV set
Be sure to unplug the mains lead connected
to the TV set from mains socket before
cleaning.
To avoid material degradation or screen
coating degradation, observe the following
precautions.
• To remove dust from the screen surface/
cabinet, wipe gently with a soft cloth. If
dust is persistent, wipe with a soft cloth
GB
10
slightly moistened with a diluted mild
detergent solution.
• Never use any type of abrasive pad,
alkaline/acid cleaner, scouring powder,
or volatile solvent, such as alcohol,
benzene, thinner or insecticide. Using
such materials or maintaining prolonged
contact with rubber or vinyl materials
may result in damage to the screen
surface and cabinet material.
• Periodic vacuuming of the ventilation
openings is recommended to ensure to
proper ventilation.
• When adjusting the angle of the TV set,
move it slowly so as to prevent the TV
set from moving or slipping off from its
table stand.
Optional Equipment
Keep optional components or any
equipment emitting electromagnetic
radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may
occur.
Batteries
• Observe the correct polarity when
inserting batteries.
• Do not use different types of batteries
together or mix old and new batteries.
• Dispose of batteries in an
environmentally friendly way. Certain
regions may regulate the disposal of
batteries. Please consult your local
authority.
• Handle the remote with care. Do not
drop or step on it, or spill liquid of any
kind onto it.
• Do not place the remote in a location
near a heat source, a place subject to
direct sunlight, or a damp room.
Disposal of the TV set
Disposal of Old
Electrical &
Electronic
Equipment
(Applicable in
the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product. The recycling of materials will
help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Disposal of
waste batteries
(applicable in the
European Union
and other
European
countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste. On certain
batteries this symbol might be used in
combination with a chemical symbol. The
chemical symbols for mercury (Hg) or
lead (Pb) are added if the battery contains
more than 0.0005% mercury or 0.004%
lead. By ensuring these batteries are
disposed of correctly, you will help
prevent potentially negative consequences
for the environment and human health
which could otherwise be caused by
inappropriate waste handling of the
battery. The recycling of the materials will
help to conserve natural resources. In case
of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery,
this battery should be replaced by qualified
service staff only. To ensure that the
battery will be treated properly, hand over
the product at end-of-life to the applicable
collection point for the recycling of
electrical and electronic equipment. For all
other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the
applicable collection point for the
recycling of waste batteries. For more
detailed information about recycling of
this product or battery, please contact your
local Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Overview of the remote
1 "/1 – TV standby
Turns the TV on and off from standby mode.
MENU
PROG
AUDIOSCENE
TOOLS
2 AUDIO
Press to change the dual sound mode (page 23).
3 SCENE – Scene Select (page 14)
4 Coloured buttons (page 14, 16)
5 / – Info/Text reveal
• In digital mode: Displays brief details of the programme currently being
watched.
• In analogue mode: Displays information such as current channel number
and screen format.
• In Text mode (page 14): Reveals hidden information (e.g. answers to a
quiz).
6 F/f/G/g/
7 TOOLS (page 14, 19)
Enables you to access various viewing options and change/make
adjustments according to the source and screen format.
8 MENU (page 21)
9 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above, press
the second and third digit in quick succession.
• In Text mode: Enters the three digit page number to select the page.
0 – Digital Favourite list
Press to display the Digital Favourite list that you have specified (page 16).
qa – Previous channel
Returns to the previous channel watched.
qs PROG +/-/ /
• In TV mode: Selects the next (+) or previous (-) channel.
• In Text mode (page 14): Selects the next ( ) or previous ( ) page.
qd 2 +/- – Volume
qf % – Mute the sound
qg / – Text (page 14)
qh RETURN /
Returns to the previous screen of any displayed menu.
qj GUIDE / – EPG (Digital Electronic Programme Guide) (page 15)
qk ANALOG – Analogue mode (page 13)
ql DIGITAL – Digital mode (page 13)
w; – Screen mode (page 14)
wa – Input select
Selects the input source from equipment connected to the TV sockets
(page 18).
z
• The number 5, PROG + and AUDIO buttons have tactile dots. Use the tactile dots
as references when operating the TV.
ANALOGDIGITAL
GUIDE
RETURN
11
GB
Overview of the TV buttons and indicators
1 1 – Power
Turns the TV on or off.
~
PROG
• To disconnect the TV completely, pull the plug
from the mains.
• When you turn on the TV, the power indicator
lights in green.
2 PROG +/-/ /
• In TV mode: Selects the next (+) or previous (-)
channel.
• In TV menu: Moves through the options up ( )
or down ( ).
3 2 +/-/ /
• In TV mode: Increases (+) or decreases (-) the
volume.
• In TV menu: Moves through the options right
() or left ().
4 / – Input select / OK
• In TV mode: Selects the input source from
equipment connected to the TV sockets
(page 18).
• In TV menu: Selects the menu or option, and
confirms the setting.
5 (page 21)
6 Remote control sensor
• Receives IR signals from the remote.
• Do not put anything over the sensor, as its
function may be affected.
7 – Picture Off / Sleep Timer indicator
• Lights up in green when the picture is switched
off (page 24).
• Lights up in orange when the sleep timer is set
(page 24).
8 1 – Standby indicator
Lights up in red when the TV is in standby mode.
9 " – Power indicator
Lights up in green when the TV is turned on.
~
• Make sure that the TV is completely turned off before
unplugging the mains lead. Unplugging the mains lead
while the TV is turned on may cause the indicator to
remain lit or may cause the TV to malfunction.
12
GB
Loading...