Sony ILX535K Datasheet
– 1 –
ILX535K
22 pin DIP (Plastic)
E97446D98-PS
5300 pixel × 3 line CCD Linear Sensor (Color)
Description
The ILX535K is a reduction type CCD linear sensor
developed for color image scanner. The distance
between lines is only 4 line (32µm). This sensor reads
A4-size documents at a density of 600DPI.
Features
• Number of effective pixels: 15900 pixels
(5300 pixels × 3)
• Pixel size: 8µm × 8µm (8µm pitch)
• Distance between line: 32µm (4 Lines)
• Number of output 3 (R, G, B)
• Single-sided readout
• Clamp circuit are on-chip
• Ultra high sensitivity/Ultra low lag
• Single 12V power supply
• Maximum data rate: 9MHz (3MHz × 3)
• Input Clock Pulse: CMOS 5V drive
• Package:
22 pin Plastic-DIP (400 mil)
Absolute Maximum Ratings
• Supply voltage VDD 15 V
• Operating temperature –10 to +55 °C
• Storage temperature –30 to +80 °C
Pin Configuration (Top View)
Block Diagram
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
5300 R 1
5300 G 1
5300 B 1
GND
GND
V
OUT-B
NC
NC
NC
NC
NC
φ2
φROG
-R
φROG-G
φRS
V
OUT-R
VDD
NC
NC
NC
NC
NC
φ1
φROG
-B
VOUT-G
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
Driver
Blue
Green
Red
φROG-B
φROG-G
φROG-R
VOUT-B
VOUT-G
VOUT-R
VDD
φ2
GND
φRS φ1
20
4
13
12
10
11
3
2
1
14
21
Clamp Pulse
Generator
Clamp
Clamp
Clamp
For the availability of this product, please contact the sales office.
– 2 –
ILX535K
Pin Description
Pin No. Symbol Description Pin No. Symbol Description
1
2
3
4
5
6
7
8
9
10
11
φRS
VOUT-R
VOUT-G
VDD
NC
NC
NC
NC
NC
φ1
φROG-B
Clock pulse input
Signal out (red)
Signal out (green)
12V power supply
NC
NC
NC
NC
NC
Clock pulse input
Clock pulse input
12
13
14
15
16
17
18
19
20
21
22
φROG-G
φROG-R
φ2
NC
NC
NC
NC
NC
VOUT-B
GND
GND
Clock pulse input
Clock pulse input
Clock pulse input
NC
NC
NC
NC
NC
Signal out (blue)
GND
GND
Recommended Supply Voltage
Item
VDD
Min.
11.4
Typ.
12
Max.
12.6
Unit
V
Clock Characteristics
Symbol
Cφ1, Cφ2
CφRS
CφROG
Min.
—
—
—
Typ.
800
10
10
Max.
—
—
—
Unit
pF
pF
pF
Item
Input capacity of φ1, φ2
Input capacity of φRS
Input capacity of φROG
∗1
Input Clock Pulse Voltage Condition
High level
Low level
Min.
4.75
—
Typ.
5.0
0
Max.
5.25
0.1
Unit
V
V
Item
φ1, φ2, φRS, φROG
pulse voltage
∗1
It indicates that φROG-R, φROG-G, φROG-B as φROG.
Clock Frequency
Min.
—
Typ.
1
Max.
3
Unit
MHz
Item Symbol
φ1, φ2, φRS fφ1, fφ2, fφRS
– 3 –
ILX535K
Electrooptical Characteristics (Note 1)
Ta = 25°C, VDD = 12V, fφRS = 1MHz, Input clock = 5Vp-p,
Light source = 3200K, IR cut filter CM-500S (t = 1.0mm)
Item Symbol Min. Typ. Max. Unit Remarks
Sensitivity
Sensitivity nonuniformity
Saturation output voltage
Saturation
exposure
Dark voltage average
Dark signal nonuniformity
Image lag
Supply current
Total transfer efficiency
Output impedance
Offset level
RR
RG
RB
PRNU
VSAT
SER
SEG
SEB
VDRK
DSNU
IL
IVDD
TTE
ZO
VOS
6.2
12.3
7.5
—
2.0
0.15
0.10
0.12
—
—
—
—
92
—
—
9.5
19
11.5
4
2.5
0.26
0.13
0.21
2
4
0.02
30
98
300
6.3
12.8
25.6
15.5
20
—
—
—
—
5
12
—
50
—
—
—
V/(lx · s)
%
V
lx · s
mV
mV
%
mA
%
Ω
V
Note 2
Note 3
Note 4
Note 5
Note 6
Note 6
Note 7
—
—
—
Note 8
Red
Green
Blue
Red
Green
Blue
Notes
1) In accordance with the given electrooptical characteristics, the black level is defined as the average value
of D2, D3 to D12.
2) For the sensitivity test light is applied with a uniform intensity of illumination.
3) PRNU is defined as indicated below. Ray incidence conditions are the same as for Note 2.
VOUT-G = 500mV (Typ.)
PRNU = × 100 [%]
Where the 5300 pixels are divided into blocks of 100. The maximum output of each block is set to VMAX,
the minimum output to VMIN and the average output to VAVE.
4) Use below the minimum value of the saturation output voltage.
5) Saturation exposure is defined as follows.
SE =
Where R indicates RR, RG, RB, and SE indicates SER, SEG, SEB.
6) Optical signal accumulated time τint stands at 5ms.
7) VOUT-G = 500mV (Typ.)
8) Vos is defined as the right side.
VOUT indicates VOUT-R, VOUT-G, and VOUT-B.
(VMAX – VMIN) /2
VAVE
A
VOS
VOUT
GND
VSAT
R
A
– 4 –
ILX535K
2
1
3
4
φROG
φ1
φ2
φRS
D1
D2
D3
D13
D14
D15
D61
D62
D63
S1
D64
D70
Optical black (49 pixels)
Dummy signal (63 pixels)
1-line output period
V
OUT
Noto) The transfer pulses (φ1, φ2) must have more than 5370 cycles.
VOUT indicates VOUT-R, VOUT-G, VOUT-B.
S5298
S2
S5299
S5300
D65
5
0
5
0
5
0
5
0
Clock Timing Chart 1
Loading...