Page 1
HXR-NX30C/NX30E/NX30J/
NX30N/NX30P/NX30U
983467512.pdf
Revision History
SERVICE MANUAL
Ver. 1.1 2012.06
Revised-1
Replace the previously issued
SERVICE MANUAL 9-834-675-11
with this Manual.
Photo: HXR-NX30U
SERVICE NOTE (Check the following note before the service.)
US Model
Canadian Model
AEP Model
E Model
Chinese Model
Japanese Model
Ver. Date History Contents
1.0 2012.05 Official Release — —
1.1 2012.06 Revised-1
(A1 12-118)
• Revision of SPECIFICATIONS.
Page 3
• Revision of REPAIR PARTS LIST.
Page 2-7
• Revision of ASSEMBLY.
Page 3-1
S.M. Rev.
issued
Ye s
– ENGLISH –
1-1. POWER SUPPLY DURING REPAIRS
1-2. PRECAUTION ON REPLACING THE VC-658 BOARD
1-3. ADDITION OF DESTINATION DATA FILE
1-4. PRECAUTION ON REPLACING THE LD-297 BOARD
1-5. SELF-DIAGNOSIS FUNCTION
1-6. METHOD OF COPING WITH SHIFT LENS ERROR
1-7. GPS RECEIVING CHECK (NX30E/NX30J/NX30N/NX30P/NX30U)
1-8. DISCHARGE OF LED FLASH/VIDEO LIGHT
1-9. NOTE ON REPLACING PROJECTOR UNIT
1-10. PRECAUTION ON REPLACING THE CABINET (BOTTOM)
‒JAPANESE‒
1-1. 修理時の電源供給について
1-2. VC-658基板交換時の注意
1-3. DestinationDataファイルの追加について
1-4. LD-297基板交換時の注意
1-5. 自己診断機能
1-6. シフトレンズエラーの対処方法
1-7. GPS受信確認(NX30E/NX30J/NX30N/NX30P/NX30U)
1-8. LEDフラッシュ／ビデオライトの放電について
1-9. プロジェクターユニット交換時の注意
1-10. キャビネット（底）交換時の注意
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
9-834-675-12
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Digital HD Video Camera Recorder
Sony Corporation
2012F08-1
© 2012.06
Published by Sony Techno Create Corporation
Page 2
These specifications are extracted from the instruction manual
of HXR-NX30E/NX30P.
– ENGLISH –
These specifications are extracted from the instruction manual
of HXR-NX30N/NX30U.
– ENGLISH –
System
Signal format: PAL color, CCIR standards
HDTV 1080/50i, 1080/50p, 720/50p
specification
Movie recording format:
HD: MPEG-4 AVC/H.264 AVCHD format
Ver.2.0 compatible
STD: MPEG2-PS
Audio recording system:
Linear PCM 2ch (48 kHz 16-bit)
Dolby Digital 2ch (48 kHz 16-bit)
Dolby Digital Stereo Creator employed
Photo file format:
DCF Ver.2.0 Compatible
Exif Ver.2.3 Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
Internal memory: 96 GB
“Memory Stick PRO Duo” media
SD card (Class 4 or faster)
The capacity that a user can use
Approx. 95.6 GB
1 GB equals 1 billion bytes, a portion of
which is used for system management and/or
application files.
Viewfinder:
Electronic viewfinder (color)
Picture: 0.5 cm (0.2 type, aspect ratio 4:3)
Total dot number: 201 600 dots equivalent
Image device:
6.3 mm (1/2.88 type) CMOS Sensor
Recording pixels (photo, 16:9):
Max. 24.1 mega (6 544 × 3 680) pixels
Gross: Approx. 6 650 000 pixels
Effective (movie, 16:9)
Approx. 6 140 000 pixels
Effective (photo, 16:9):
Approx. 6 140 000 pixels
Effective (photo, 4:3):
Approx. 4 600 000 pixels
Lens:
Carl Zeiss Vario-Sonnar T*
10 × (Optical)
recording movies)
Filter diameter: 52 mm (2 1/8 in.)
37 mm (1 1/2 in.) (When attaching the Step
Down Ring)
F1.8 - F3.4
Focal length:
f= 3.8 mm - 38.0 mm (5/32 in. ~ 1 1/2 in.)
When converted to a 35 mm still camera
For movies
10 1/4 in.) (16:9)
For photos: 26.0 mm - 260 mm (1 1/16 in. ~
10 1/4 in.) (16:9)
Color temperature: [Auto], [One Push], [Indoor]
(3 200 K), [Outdoor] (5 800 K)
Minimum illumination:
6 lx (lux) (in default setting, shutter speed
1/50 second)
3 lx (lux) ([Low Lux] is set to [On], shutter
speed 1/25 second)
0 lx (lux) (NIGHTSHOT is set to [On])
*1
*2
*3
*2
The unique pixel array of Sony’s ClearVid
and the image processing system allow still
image resolution equivalent to the sizes
described.
[ SteadyShot] is set to [Standard] or
[Off].
[ SteadyShot] is set to [Active].
*2
:
*2
, 17 × (Extended, while
*3
, 120 × (Digital)
: 26.0 mm - 260 mm (1 1/16 in. ~
*1
SPECIFICATIONS
Input/Output connectors
A/V Remote Connector: Video and audio output
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
(output only)
Headphone jack: Stereo minijack (
MIC input jack: Stereo minijack (
INPUT1/INPUT2 jack: XLR3-pin, female
MIC: -60 dBu /-50 dBu /-40 dBu, 3 kΩ
(kilohms)
LINE: +4 dBu, 10 kΩ (kilohms)
(0 dBu=0.775 Vrms)
LCD screen
Picture: 7.5 cm (3.0 type, aspect ratio 16:9)
Total number of pixels:
921 600 (1 920 × 480)
Projector
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
supplied battery pack):
Approx. 3 h 25 min.
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
USB Charging: DC 5 V 500 mA/1.5 A
Average power consumption:
During camera recording using the
microphone (ECM-XM1), the viewfinder at
normal brightness:
HD: 3.9 W STD: 3.7 W
During camera recording using the
microphone (ECM-XM1), the LCD screen at
normal brightness:
HD: 4.1 W STD: 3.8 W
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
Dimensions (approx.):
71.5 mm × 94.5 mm × 137.5 mm (2 7/8 in.
× 3 3/4 in. × 5 1/2 in.) (w/h/d) including the
projecting parts
135.5 mm × 181.5 mm × 310.5 mm (5 3/8 in.
× 7 1/4 in. × 12 1/4 in.) (w/h/d) including
the projecting parts, the supplied lens hood,
battery (NP-FV70), XLR Adaptor, and the
microphone (ECM-XM1)
Mass (approx.)
615 g (1 lb 5 oz) main unit only
1 100 g (2 lb 6 oz) including the supplied lens
hood, battery (NP-FV70), XLR Adaptor, and
the microphone (ECM-XM1)
φ 3.5 mm)
φ 3.5 mm)
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
Dimensions (approx.): 48 mm × 29 mm ×
81 mm (1 15/16 in. × 1 3/16 in. × 3 1/4 in.)
(w/h/d) excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FV70
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 3.0 A
Capacity
Typical: 14.0 Wh (2 060 mAh)
Minimum: 13.0 Wh (1 960 mAh)
Type: Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
System
Signal format: NTSC color, EIA standards
HDTV 1080/60i, 1080/60p, 720/60p
specification
Movie recording format:
HD: MPEG-4 AVC/H.264 AVCHD format
Ver.2.0 compatible
STD: MPEG2-PS
Audio recording system:
Linear PCM 2ch (48 kHz 16-bit)
Dolby Digital 2ch (48 kHz 16-bit)
Dolby Digital Stereo Creator employed
Photo file format:
DCF Ver.2.0 Compatible
Exif Ver.2.3 Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
Internal memory: 96 GB
“Memory Stick PRO Duo” media
SD card (Class 4 or faster)
The capacity that a user can use
Approx. 95.6 GB
1 GB equals 1 billion bytes, a portion of
which is used for system management and/or
application files.
Viewfinder:
Electronic viewfinder (color)
Picture: 0.5 cm (0.2 type, aspect ratio 4:3)
Total dot number: 201 600 dots equivalent
Image device:
6.3 mm (1/2.88 type) CMOS Sensor
Recording pixels (photo, 16:9):
Max. 24.1 mega (6 544 × 3 680) pixels
Gross: Approx. 6 650 000 pixels
Effective (movie, 16:9)*2:
Approx. 6 140 000 pixels
Effective (photo, 16:9):
Approx. 6 140 000 pixels
Effective (photo, 4:3):
Approx. 4 600 000 pixels
Lens:
Carl Zeiss Vario-Sonnar T*
10 × (Optical)*2, 17 × (Extended, while
recording movies)*3, 120 × (Digital)
Filter diameter: 52 mm (2 1/8 in.)
37 mm (1 1/2 in.) (When attaching the Step
Down Ring)
F1.8 - F3.4
Focal length:
f= 3.8 mm - 38.0 mm (5/32 in. ~ 1 1/2 in.)
When converted to a 35 mm still camera
For movies*2: 26.0 mm - 260 mm (1 1/16 in.
~ 10 1/4 in.) (16:9)
For photos: 26.0 mm - 260 mm (1 1/16 in. ~
10 1/4 in.) (16:9)
Color temperature: [Auto], [One Push], [Indoor]
(3 200 K), [Outdoor] (5 800 K)
Minimum illumination:
6 lx (lux) (in default setting, shutter speed
1/60 second)
3 lx (lux) ([Low Lux] is set to [On], shutter
speed 1/30 second)
0 lx (lux) (NIGHTSHOT is set to [On])
*1
The unique pixel array of Sony’s ClearVid
and the image processing system allow still
image resolution equivalent to the sizes
described.
*2
[ SteadyShot] is set to [Standard] or [Off].
*3
[ SteadyShot] is set to [Active].
*1
SPECIFICATIONS
Input/Output connectors
A/V Remote Connector: Video and audio output
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
(output only)
Headphone jack: Stereo minijack (φ 3.5 mm)
MIC input jack: Stereo minijack (φ 3.5 mm)
INPUT1/INPUT2 jack: XLR3-pin, female
MIC: -60 dBu /-50 dBu /-40 dBu, 3 kΩ
(kilohms)
LINE: +4 dBu, 10 kΩ (kilohms)
(0 dBu=0.775 Vrms)
LCD screen
Picture: 7.5 cm (3.0 type, aspect ratio 16:9)
Total number of pixels:
921 600 (1 920 × 480)
Projector
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
supplied battery pack):
Approx. 3 h 25 min.
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
USB Charging: DC 5 V 500 mA/1.5 A
Average power consumption:
During camera recording using the
microphone (ECM-XM1), the viewfinder at
normal brightness:
HD: 3.9 W STD: 3.7 W
During camera recording using the
microphone (ECM-XM1), the LCD screen at
normal brightness:
HD: 4.1 W STD: 3.8 W
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
Dimensions (approx.):
71.5 mm × 94.5 mm × 137.5 mm (2 7/8 in.
× 3 3/4 in. × 5 1/2 in.) (w/h/d) including the
projecting parts
135.5 mm × 181.5 mm × 310.5 mm (5 3/8 in.
× 7 1/4 in. × 12 1/4 in.) (w/h/d) including
the projecting parts, the supplied lens hood,
battery (NP-FV70), XLR Adaptor, and the
microphone (ECM-XM1)
Mass (approx.)
615 g (1 lb 5 oz) main unit only
1 100 g (2 lb 6 oz) including the supplied lens
hood, battery (NP-FV70), XLR Adaptor, and
the microphone (ECM-XM1)
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
Dimensions (approx.): 48 mm × 29 mm ×
81 mm (1 15/16 in. × 1 3/16 in. × 3 1/4 in.)
(w/h/d) excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FV70
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 3.0 A
Capacity
Typical: 14.0 Wh (2 060 mAh)
Minimum: 13.0 Wh (1 960 mAh)
Type: Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
– 2 –
Page 3
Ver. 1.1 2012.06
The changed portions from
Ver. 1.0 are shown in blue.
システム
信号方式
NTSCカラー、EIA標準方式
HDTV1080/60i方式、1080/60p、
720/60p方式
ビデオ記録方式
HD画質:MPEG-4AVC/H.264
AVCHD規格Ver.2.0準拠
STD画質:MPEG-2PS
音声記録方式
リニアPCM2ch（48kHz16bit）
DolbyDigital2ch（48kHz16bit）
ドルビーデジタルステレオクリエーター搭載
静止画ファイルフォーマット
:DCFVer2.0準拠
:ExifVer2.3準拠
:MPFBaseline準拠
記録メディア（動画・静止画）
内蔵メモリー :96GB
メモリースティックPROデュオ
SDカード（Class4以上）
使用可能容量:約95.6GB
容量は、1GBを10億バイトで計算した場合の
数値です。また管理用ファイル、アプリケーショ
ンファイルなどを含むため、実際に使用できる
容量は減少します。
ファインダー
電子ファインダー :カラー
画面サイズ:0.5cm（0.2型、アスペクト比4:3）
総ドット数:201600ドット相当
撮像素子:
6.3mm（1/2.88型）CMOSセンサー
記録画素数:
静止画時最大2410万画素相当
（6544×3680）（16:9時）
総画素数:約665万画素
動画時有効画素数
静止画時有効画素数（16:9）:約614万画素
静止画時有効画素数（4:3）:約460万画素
ズームレンズ:カールツァイスバリオ・ゾナー T*
10倍（光学）
時のみ）
52mm
37mm（ステップダウンリング装着時）
F1.8˜F3.4
f=3.8mm-38.0mm
35mmカメラ換算では
動画撮影時
f=26.0mm-260mm（16:9）
静止画撮影時:
f=26.0mm-260mm（16:9）
色温度切り換え:［Auto］、［OnePush］、［Indoor］
（3200K）、［Outdoor］（5800K）
最低被写体照度:
6lx（ルクス）（お買い上げ時、［ShutterSpeed］
1/60秒）
3lx（ルクス）（［LowLux］が［On］時、［Shutter
Speed］1/30秒）
0lx（ルクス）（NIGHTSHOT時）
*1
ソニー独自のクリアビッド画素配列と画像処
理システムにより、静止画は表記の記録サイ
ズを実現しています。
*2
［ SteadyShot］が［Standard］、または
［Off］のとき
*3
［ SteadyShot］が［Active］のとき
*1
*2
（16:9）:約614万画素
*2
、17倍（エクステンデッド、動画
*3
、120倍（デジタル）フィルター径:
*2
:
概略仕様
入/出力端子
A/Vリモート端子:映像音声出力兼用端子
HDMIOUT端子:HDMIミニコネクタ
USB端子:mini-AB/タイプA（ビルトインUSB）（出
力のみ）
ヘッドホン端子:ステレオミニジャック（φ3.5mm）
MIC入力端子:ステレオミニジャック（φ3.5mm）
INPUT1/INPUT2端子:XLR型3ピン、凹
MIC:-60/-50/-40dBu、3kΩ
LINE:+4dBu、10kΩ
（0dBu=0.775Vrms）
液晶モニター
画面サイズ:7.5cm（3.0型、アスペクト比16:9）
総ドット数:921600ドット
横1920×縦480
プロジェクター
表示方式:DLP
光源:LED（R/G/B）
フォーカス:マニュアル
投写距離（約）:最低0.5m以上
コントラスト比:1500:1
解像度（出力）:nHD（640×360）
連続投影可能時間（付属バッテリー使用時）:
約3時間25分
電源部、その他
電源電圧:バッテリー端子入力6.8V/7.2V
DC端子入力8.4V
USB充電:DC5V500mA/1.5A
消費電力:
マイク（ECM-XM1）、ファインダー使用時、
明るさ標準:
HD:3.9WSTD:3.7W
マイク（ECM-XM1）、液晶モニター使用時、
明るさ標準:
HD:4.1WSTD:3.8W
動作温度:0℃ ˜40℃
保存温度:-20℃ ˜+60℃
外形寸法（約）:
71.5mm×94.5mm×137.5mm
(突起部を含む)(幅×高さ×奥行き)
135.5mmx181.5mmx310.5mm
(突起部、レンズフード、バッテリー (NP-FV70)、
XLRアダプター、マイク(ECM-XM1)を含む)
(幅×高さ×奥行き)
本体質量（約）:
615g（本体のみ）
撮影時総質量（約）:
1 100 g（レンズフード、バッテリー（NP-
FV70）、XLRアダプター、マイク（ECM-XM1）
を含む）
– JAPANESE –
ACアダプター AC-L200C/AC-L200D
電源:AC100V-240V、50Hz/60Hz
消費電流:0.35A-0.18A
消費電力:18W
定格出力:DC8.4V*
動作温度:0℃ ˜40℃
保存温度:-20℃ ˜+60℃
外形寸法:約48mm×29mm×81mm（最大突
起部を除く）（幅×高さ×奥行き）
質量:約170g（本体のみ）
* その他の仕様についてはACアダプターのラベルを
ご覧ください。
リチャージャブルバッテリーパック
NP-FV70
最大電圧:DC8.4V
公称電圧:DC6.8V
容量:
公称容量:14.0Wh（2060mAh）
定格（最小）容量:13.0Wh（1960mAh）
使用電池:Li-ion
本機やアクセサリーの仕様および外観は、改良のた
め予告なく変更することがありますが、ご了承くだ
さい。
・ ドルビーラボラトリーズからの実施権に基づき製
造されています。
Model information table
Model NX30C NX30E NX30J NX30N NX30P NX30U
Destination CH AEP J E E US, CND
Color system PAL PAL NTSC NTSC PAL NTSC
Recording media Internal memory
96 GB
Internal memory
96 GB
Internal memory
96 GB
Internal memory
96 GB
Internal memory
96 GB
Internal memory
96 GB
Lens LSV-1550A-BI LSV-1550A-BI LSV-1550A-BI LSV-1550A-BI LSV-1550A-BI LSV-1550A-BI
Projector
GPS
EVF
Hot shoe
Charging capacitor
(for flash)
333333
–
33333
333333
333333
––––––
MODEL GROUP
GPS Model: NX30E/NX30J/NX30N/NX30P/NX30U
Non GPS Model: NX30C
• Abbreviation
CH: Chinese model
CND: Canadian model
J: Japanese model
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
– 3 –
Page 4
– ENGLISH – – JAPANESE –
Danger of explosion if battery is incorrectly replaced.
Caution
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are pinched or
contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing unleaded solder and leaded solder will cause detachment phenomenon.
電池の交換は，正しく行わないと破裂する恐れがあります。
注意
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は，取扱指示に従って処分してください。
サービス，点検時には次のことにご注意ください。
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，キャビ
ネット，シャーシ，部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は，使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図，部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用したり，
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので，これらは必
ずもとどおりにして下さい。
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとどおり
になっているか，またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し，安全性が確保さ
れていることを確認して下さい。
5. チップ部品交換時の注意
・ 取外した部品は再使用しないで下さい。
・ タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6. フレキシブルプリント基板の取扱いについて
・ 半田こてのこて先温度は約350℃に設定してください。
・ 同一パターンに何度もコテ先を当てないで下さい。（3回
以内）
・ パターンに力が加わらないよう注意して下さい。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には，無鉛（LeadFree）を意味する
レッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す）
：レッドフリーマーク
無鉛半田は，下記の点に注意して使用してください。
・ 半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は，高温短時間で作業を行ってくだ
さい。
注意：半田こてを長く当てすぎると，基板のパターン（銅
箔）がはがれてしまうことがありますので，注意して
ください。また，従来の半田よりも粘性が強いため，
IC端子などが半田ブリッジしないように注意してく
ださい。
・ 半田こてのこて先は，必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
– 4 –
Page 5
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1. SERVICE NOTE
– ENGLISH –
START
Connect to the PC with a USB cable,
and turn on the power switch.
* by SEUS driver
1-2. PRECAUTION ON REPLACING THE VC-658 BOARD
Note the following when replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Data for projector
Before replacing the board with a spare board, acquire the following data from the current board.
• Fixed value (that shows irradiation performance of the projector).
• Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.
About unit with Internal Memory Model
After the board replacement, execute the procedure below first.
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
• 11DdmMmcReadTestMINI_v4.vbe
1DdmMmcMakePartition_v4.vbe
• 1
Note: Download the script files from TISS Homepage.
When searching in the TISS Homepage, enter “IM_VC_TOOL” for keyword in the Part Number field.
Select the "USB CONNECT" to establish
the connection
Execute
the "DdmMmcReadTestMINI.vbe"
(several second)
Wait until "SetOverallReadMINI OK" display
During the power is turning-on,
pull-out the AC-adapter.
Then connect the AC-adapter Again
(It's running with blue color monitor.)
Reactive the camcorder automatically
Execute
the "11DdmMMCMakePartition.vbe"
(several second)
Wait until "MakePartition OK" display
Reactive the camcorder automatically
Unless these script files are executed, the following symptoms may appear.
Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
• The internal memory cannot be formatted.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Disconnect the USB cable,
and turnoff the power switch.
END
Fig.1
1-1
Page 6
1-3. ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
– ENGLISH –
3) Search the model whose new Destination Data file you want to get on the TISS homepage.
When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.
(Example) Destination File For DSC-WX50.zip
Note 1: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2: The actual image may differ from the image shown above.
1) If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
Click the [OK] button.
Fig. 1
2) The Destination Data Write window opens.
Check the version of the Destination Data file retained in the Adjust manual.
Furthermore, the version supported by the Destination Data file is shown in the Remarks column.
Note : If the Destination Data file has not been updated, contact the Service Headquarters.
4) Download the Destination Data file of the relevant model and unzip the file.
Destination Ver. window
5) Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
Click the [START] button.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-2
Page 7
6) Click the [File Update] button in the window.
– ENGLISH –
1-4. PRECAUTION ON REPLACING THE LD-297 BOARD
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7501 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
LD-297 BOARD (SIDE A)
7) A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
8) When the file has been successfully added, the following window opens.
SE7501
PPP
YYY
Note: The sensor sensitivity of SE7501 (PITCH/YAW) on LD-297 board is written only repair parts.
PPP: PITCH sensor sensitivity
YYY: YAW sensor sensitivity
G1
G2
9) Check the Destination Ver. window and confirm that the version has been updated.
Destination Ver. window
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-3
Page 8
1-5. SELF-DIAGNOSIS FUNCTION
– ENGLISH –
Self-diagnosis Code
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
LCD screen
Blinks at 3.2 Hz
00
Detailed Code
Refer to “1-5-3. Self-diagnosis Code Tabl e”.
Repaired by:
C : Corrected by customer
E : Corrected by service
engineer
32C
Block
Indicates the appropriate
step to be taken.
E.g.
13 ....
Format the “memory card”.
32 ....Turn on power again.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the LCD
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Block
Function
Repaired by:
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
C 0 6 0 0 The battery pack temperature is high. Change the battery pack or place it in a cool place.
C1 3 0 1
C 1 3 0 2 Access error
C 1 3 0 3 Access error (External mdedia) Turn power off and turn power on again.
Detailed
Code
Memory card is unformatted.
Memory card is broken.
*
*
Symptom/State Correction
Format the memory card.
Insert a new memory card.
Remove the power source. Reconnect it again and operate your camcorder again.
Block
Function
Repaired by:
E6 1 1 0
E6 1 1 1
E6 1 3 0
E6 2 0 0
E6 2 0 1
E 6 2 0 2 Abnormality of IC for steadyshot.
E6 2 0 3
E6 2 0 4
E 6 2 1 0 Shift lens initializing failure.
E 6 2 1 1 Shift lens overheating (Pitch) Refer to [1-6-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred].
E 6 2 1 2 Shift lens overheating (Yaw) Refer to [1-6-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred].
E 6 2 2 0 Abnormality of thermistor. Refer to [1-6-4. E : 62 : 20 (Abnormality of Thermistor) Occurred].
E 9 1 0 1 Abnormality when flash is beingcharged. Check or replace the LED Flash/Video light or charging capacitor.
E 9 1 0 2 Abnormality of LED Video light. Check or replace the LED Flash/Video light or charging capacitor.
Detailed
Code
Zoom operations fault
(Cannot initialize zoom lens.)
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Reset position detection error on the stepper
iris initializing
Handshake correction function does not work
well. (With PITCH angular velocity sensor
output stopped.)
Handshake correction function does not work
well. (With YAW angular velocity sensor
output stopped.)
IC for steadyshot and micro controller communication abnormality among.
Image vibration correction during
handshake function does not work.
Symptom/State Correction
Inspect the lens block zoom sensor signal (pin 1, qh of CN4003 on
the LD-297 board when zooming is performed when the zoom lever
is operated, and the zoom motor drive circuit (IC5201 on the LD-297
board) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin 5, qz, qk, ql, wk, wl of CN4003 on the LD-297 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
･ Case of the iris blades do not close normally Replace the lens block).
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
･ Case of LCD is not displayed normally Check that connection be-
tween CN6701 on CM-121 board and CN1004 on VC-658 board
by FP-1520 flexible board.
･ Case of LCD is displayed normally Replace the lens block.
Inspect PITCH angular velocity sensors (SE7501 on the LD-297
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE7501 on the LD-297 board)
peripheral circuits.
Refer to [1-6-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Occurred].
Inspect the steadyshot circuit (IC5601 on the LD-297 board).
Inspect the image vibration angular velocity sensors (SE7701 on the
CK-244 board) peripheral circuits.
Replacement of lens block (Note 3).
If an error occurs again, replace the LD-297 board.
C 1 3 0 4 Drive fault (External mdedia) Turn power off and turn power on again.
CE32
( )
61
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Turn power off and turn power on again.
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.
*
60
00
*
Difficult to adjust focus
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover,
check the focus MR sensor of lens block (pin 2, qf of CN4003 on the
LD-297 board). If it is OK, check the focus motor drive IC (IC1301 on
the VC-658 board).
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-4
E9 1 0 3
E9 2 0 1
E9 4 0 0
E 9 4 0 1 Internal flash memory fault Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
Abnormality of LED Video light Temperature detection.
Battery current value goes over the max
discharge current
Fault of writing or erasing the flash memory
Check or replace the LED Flash/Video light or charging capacitor.
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symptom is still occurred, overhaul inspection is needed. Check each
output of DC/DC converter (IC4301 on the VC-658 board) with
connected the DC JACK (J901) on the VC-658 board.
(The minimum connection to periphery)
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
Page 9
Self-diagnosis Code
– ENGLISH –
Block
Function
Detailed
Code
Symptom/State Correction
Repaired by:
E 9 4 0 2 BGM data error Check the CPU (IC1301 on the VC-658 board).
NX30E/NX30J/NX30N/NX30P/NX30U:
Check whether the FFC-254 flexible flat cable is broken, and check
E 9 5 0 0 GPS hardware error
whether it is inserted imperfectly.
If there is no problem the flexible board, inspect or replacement of
the GP-037 board.
E 9 6 0 0 Map area mount error
NX30E/NX30J/NX30N/NX30P/NX30U:
Inspect or replacement of the LD-297 board.
E 9 7 0 0 Projector hardware error Turn power off and turn power on again.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6. METHOD OF COPING WITH SHIFT LENS ERROR
LD-297 BOARD (SIDE A) LD-297 BOARD (SIDE B)
about 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5632 on the LD-297 board
1-6-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order Procedure
1 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the LD-297 board, turn the
2
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
3
the camera control circuit (IC1301 of VC-658 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order AdjustBlock AdjustCode Order
1
2
3
4
5 Turn the power OFF.
6
7
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the
[SERVICE] tab.
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
While setting the order 1, measure with an oscilloscope the output voltage of C5642 and C5643 in
the periphery of IC5601 on the LD-297 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the
LD-297 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-658 board
and IC5601 of LD-297 board) periphery.
C5636 C5640
C5642 C5643
IC5601
Measurement points on the LD-297 board
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
R5632
Fig. 1
1-5
Page 10
1-6-3.E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
– ENGLISH –
1-7. GPS RECEIVING CHECK (NX30E/NX30J/NX30N/NX30P/NX30U)
Order AdjustBlock AdjustCode Order
1
2
3
4
5 Turn the power OFF.
6
7
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SERVICE] tab.
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
While setting the order 1, measure with an oscilloscope the output voltage of C5636 and C5640 in the
periphery of IC5601 on the LD-297 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
While measuring with an oscilloscope the output voltage of R5632 in the periphery
of IC5601 on the LD-297 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-658 board
and IC5601 of LD-297 board) periphery.
1-6-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order Procedure
1 Turn the power ON.
After a part of set was replaced or after the set was assembled, check the reception of GPS signal.
How to check the GPS function
Bring your camcorder to an open area, and set the GPS to ON ( appears on the LCD screen). Your camcorder starts trying to triangulate. When
your camcorder triangulates successfully, it will record the location information at the time movies and photos were recorded.
• The indicator changes according to the strength of GPS signal reception.
2 Confirm the connections of flexible flat cables and connectors between the lens block and LD-297 board.
In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens
3
replacement, replace LD-297 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
• It may take a while before the camcorder starts triangulating.
To return the display of the unit to “A message appears asking you to confirm whether you agree with the terms of the license agreement of the map
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.
Use GPS Assist Data
If you import GPS Assist Data from your computer to your camcorder using the supplied software “PlayMemories Home,” the time it takes the camcorder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-6
Page 11
1-8. DISCHARGE OF LED FLASH/VIDEO LIGHT
– ENGLISH –
Projector problem checking procedure (indication on brightness)
This model is provided with a flash unit using LED Flash/Video light.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.
1-9. NOTE ON REPLACING PROJECTOR UNIT
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flowchart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Indication on
brightness
Yes
No
B
Indicated defective
projector received
Indication on
brightness
Yes
Measure brightness.
( 2)
OK
No
NG
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
B
A
-
Replace projector unit (light emitting block). (*1)
-
Replace PJ board. (*1)
-
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
-
Fixed value input
Enter the number on the label attached to the unit.
-
Serial number input
LD40Syywwnnnnn Enter the red part.
Inspect projector
LED.
( 1)
OK
NG
Measure brightness.
( 2)
OK OK
NG
A
END
Inspect projector
LED.
( 1)
NG
-
Replace projector unit (light emitting block). (*1)
-
Replace PJ board. (*1)
-
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
-
Fixed value input
Enter the number on the label attached to the unit.
-
Serial number input
LD40Syywwnnnnn Enter the red part.
Inspect projector
LED.
( 1)
OK
NG
END
Measure brightness.
( 2)
OK
NG
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-7
Page 12
1-10. PRECAUTION ON REPLACING THE CABINET (BOTTOM)
1-10-1. Precaution on ordering the CABINET (BOTTOM)
The model display adopts the laser printing method.
Therefore, the Cabinet (Bottom) for replacement differs depending on
the destination.
Choose the suitable one for order.
Note: After replacing the Cabinet (Bottom) , the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the
serial number in the repair data.
– ENGLISH –
1-10-2. Precaution on Replacing the CABINET (BOTTOM) for HXR-NX30J
The year of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “12” label.
* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
If you need labels, place an order for 4-424-330-01.
HXR-NX30J
Serial No. Serial No. Serial No.
Part No. Description
A-1889-063-A CABINET (BOTTOM)
HXR-NX30P
Serial No.
Part No. Description
A-1889-066-A CABINET (BOTTOM)
HXR-NX30U
Part No. Description
A-1889-064-A CABINET (BOTTOM)
HXR-NX30E
Serial No. Serial No.
Part No. Description
A-1889-067-A CABINET (BOTTOM)
HXR-NX30NHXR-NX30J
Part No. Description
A-1889-065-A CABINET (BOTTOM)
HXR-NX30C
Part No. Description
A-1889-068-A CABINET (BOTTOM)
* Manufacturing year
* Affix the label
1-10-3. Precaution on Replacing the CABINET (BOTTOM) for HXR-NX30U
The date of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “2B” labels.
* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
If you need labels, place an order for 4-415-879-01.
HXR-NX30U
* Manufacturing year
* Affix the label
1-10-4. Precaution on Replacing the CABINET (BOTTOM) for HXR-NX30N
The date of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “2012-05” label.
* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
If you need labels, place an order for 4-424-330-01.
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
HXR-NX30N
* Manufacturing year
* Affix the label
1-8
Page 13
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
ACアダプタを使用する。
– JAPANESE –
START
セットをPCにUSB接続し、電源を入れる
* PCはSeusEX がインストール済で，
SeusEXへの接続が可能であること
1-2. VC-658基板交換時の注意
基板交換時は，下記の点に注意してください。
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
AdjustStationからAdjustManualを起動させて「DESTINATIONDATAWRITE」を実行させてください。
補修用基板交換後、電源を入れると内蔵記録メディアエラーが表示される場合がありますが、「DESTINATIONDATAWRITE」を実行
させると消えます。「DESTINATIONDATAWRITE」実行しても消えない場合は、内蔵記録メディアをフォーマットしてください。
USBシリアルセーブ
補修用基板と交換する時，交換前の基板よりUSBシリアルNo.を取得してください。
データの取得はAdjustStationからAdjustManualを起動させて「USBSERIALSAVE」を実行させてください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USBSerialNo.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
AdjustStationからAdjustManualを起動させて「USBSERIALNo.INPUT」を実行させてください。
プロジェクター用のデータ
補修用基板と交換する時，交換前の基板より下記のデータを取得してください。
・ Fixedvalue（プロジェクターの照射性能を示す値）。
・ Serialnumber（プロジェクターユニットの製造シリアル番号）。
データの取得はAdjustStationからAdjustManualを起動させて、[DATA]タブにある[ProjectorDataReference]を参照してください。
内蔵メモリー搭載機について
補修用基板に交換後は，最初に下記の手順を実行してください。
1. AdjustManualのADJUSTタブにある，「DESTINATIONDATAWRITE」を実行する。
2. 下記のスクリプトファイルを実行する。
・ 11DdmMmcReadTestMINIv4.vbe
・ 11DdmMmcMakePartitionv4.vbe
Note: スクリプトファイルはTISSホームページより入手してください。
TISSホームページで検索する際はPartNumber欄に「IMVCTOOL」と入力して検索してください。
USB接続を選択し、
USB接続を行う
DdmMmcReadTestMINI.vbe
を実行
（数秒後）
SetOverallReadMINI OK表示
電源を入れたまま、
ACアダプタを抜き挿しする
処理は自動で実行される
（Blue画面）
（約10秒後）
セットが自動的に再起動される
11DdmMMCMakePartition.vbe
を実行
（数秒後）
MakePartition OK表示
セットが自動的に再起動される
このスクリプトファイルを実行しなかった場合，以下のような症状が発生する可能性があります。
必ず上記のスクリプトを実行してください。
・ 内蔵メモリーがメディアとして認識できない
・ 内蔵メモリー内に保存されている，管理ファイルの修復ができない
・ 内蔵メモリーのフォーマットができない
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
USB接続を解除し、電源を切る
END
Fig.1
1-9
Page 14
1-3. DestinationDataファイルの追加について
Adjustmanualに含まれるDestinationDataファイルが古い場合，「DESTINATIONDATAWRITE」が実行できないことがあります。
その場合は，下記の手順を参考にして，TISSホームページより新しいDestinationDataファイルを入手してください。
Note1： この機種で仕向け設定を行うには，DSC-WX50シリーズのAdjustmanualがインストールされている必要があります。
先にDSC-WX50シリーズのAdjustmanualをインストールしてください。
Note2： 手順中の画像は実際と異なる場合があります。
1) 使用しているAdjustmanualのDestinationDataファイルが古い場合，Fig.1のようなウインドウが表示される。
[OK]ボタンをクリックする。
Fig. 1
2) DestinationDataWriteウインドウが表示される。
Adjustmanualの保持しているDestinationDataファイルのバージョンを確認する。
– JAPANESE –
3) TISSホームページにて，新しいDestinationDataファイルを入手したい機種を検索する。
DestinationData ファイルが更新されている場合，「DestinationFileFor”機種名”.zip」 という名称のファイルが登録されてい
る。
(例)DestinationFileForDSC-WX50.zip
また，Remarks欄にはこのDestinationDataファイルが対応するバージョンが記載されています。
Note：バージョンが更新されていなかった場合は，サービスヘッドクォーターへお問い合わせください。
Destination Ver. ウインドウ
4) 該当機種のDestinationDataファイルをダウンロードし，解凍する。
5) AdjustmanualのAdjustタブにある，「DESTINATIONDATAWRITE」を実行する。
[START]ボタンをクリックする。
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-10
Page 15
6) ウインドウ内の[FileUpdate]ボタンをクリックする。
7) ファイルを選択する画面が出るので，追加するDestinationDataファイルを選択し，[開く]ボタンをクリックする。
1-4. LD-297基板交換時の注意
角速度センサ
補修用基板と交換する時，角速度センサSE7501(PITCH/YAW)の感度表示を書き留めてください。
AdjustStationからAdjustManualを起動させて「GYROsensorsensitivityadj.」を実行させてくだ
LD-297 BOARD (SIDE A)
SE7501
PPP
PPP
YYY
Note：LD-297基板のSE7501(PITCH/YAW)感度表示は補修用基板にのみ記載されています。
PPP: PITCH 感度表示
YYY: YAW 感度表示
G1
G2
– JAPANESE –
8) ファイルの追加が成功すると，下記のような画面が出る。
9) DestinationVer.ウインドウを確認し，バージョンが更新されていることを確認する。
Destination Ver. ウインドウ
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-11
Page 16
1-5. 自己診断機能
1-5-1.自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，LCD
画面に，どう処置したらよいか判断できる表示を行います。「自
己診断表示」と「サービスモード表示」の２つの表示があります。
自己診断機能については取扱説明書にも掲載されています。
LCD画面
3.2Hz点滅
C23
00
1-5-2.自己診断表示
本機の動作に不具合が生じたとき，LCD画面のカウンタ表示部
分がアルファベットと数字の4桁表示になり，3.2Hzで点滅しま
す。この5文字の表示によって対応者分類および不具合の生じ
たブロックの分類，不具合の詳細コードを示します。
– JAPANESE –
自己診断コード
対
ブロック
応
機能
者
E6 1 1 0
E 6 1 1 1 フォーカス，ズーム異常 自己診断コードC：32：60とE：61：10の両方を点検する。
E61 30
詳細
コード
ズーム動作の異常（ズームレン
ズの初期化ができない）
ステッパIRISイニシャル時リセット
位置検出異常
症状／状態 対応／方法
ズームレバーを操作したときにズーム動作をすれば，レンズブロッ
クのズームセンサー信号（LD-297基板CN40031，qhピン）を点検す
る。
ズーム動作をしなければズームモータ駆動回路（LD-297基板IC5201）
を点検する。
電源を入れてレンズバリアが開いている状態で、バッテリまたは電源ケーブル
をはずして付け直す。
その際、レンズ内のアイリス羽根が動作していることを確認する。
アイリス羽根が動作してない場合は、レンズドライブブロックのアイリスモー
タドライブ（LD-297基板CN4003
アイリス羽根が動作する場合は、アイリス羽根が完全に閉じきることを確認し、
以下の内容を確認する。
・アイリス羽根を正常に閉じることができない場合レンズブロックを交換す
る。
・アイリス羽根は正常に閉じているが、E:61:30が出る場合CMOSブロック組
立との通信ができているかを確認する。
・正常に画面が出ていない場合CM-121基板のCN6701とVC-658基 板 の
CN1004がFP-1520フレキシブル基板で接続されているかを確認する。
・正常に画面が出ている場合レンズブロックを交換する
5
，qz，qk，ql，wk，
wl
ピン）を点検する。
対応者分類
C：お客さま自身で対応
E ：サービスエンジニア
で対応
ブロック分類
対応方法の違いにより分類
例
32 ･･･電源を入れ直す
詳細コード
「1‑5‑3.自己診断コード表」を参照
･メモリーカードをフォーマットする･･31
1-5-3. 自己診断コード表
自己診断コード
対
ブロック機能詳細
応
者
コード
C 0 4 0 0 標準以外のバッテリを使用している インフォリチウムバッテリを使用する。
C 0 6 0 0 バッテリが高温になっている バッテリを交換するか, バッテリを涼しいとこに置く。
フォーマットしていないメモリー
C1 3 0 1
カードを入れた
メモリーカードが壊れている
C 1 3 0 2 アクセスエラー 電源を外し，再度入れ直してから操作する。
C 1 3 0 3 アクセスエラー(外部メディア) 電源を入れ直す。
C 1 3 0 4 ドライブの異常(外部メディア) 電源を入れ直す。
CE32
( )
61
60
00
E2 0 0 0
E 3 1 0 0 ドライブの異常 電源を入れ直す。
注意1： AdjustStationからAdjustManualを起動させて「DESTINATIONDATAWRITE」を参照してください。
注意2： *マークのコードは本機には実装されていない機能です。
*
*
*
フォーカスが合いにくい
（フォーカスの初期化ができない）
フラッシュメモリが書き換えられて
いる
*
症状／状態 対応／方法
メモリーカードをフォーマットする。
新しいメモリーカードに交換する。
操作スイッチの電源を入れ直す。
復帰しない場合，レンズブロックのフォーカスMRセンサ（LD297基板CN40032，qfピン）を点検する。
異常なければフォーカスモータ駆動回路（VC-658基板IC1301）
を点検する。
フラッシュメモリのデータを元の値に戻す。（注意1）
E62 00
E62 01
E 6 2 0 2 手振れ補正用ICの異常 「1-6-1.E：62：02（手振れ補正用ICの異常）が出た場合」を参照。
E62 03
E62 04
E 6 2 1 0 シフトレンズ初期化異常
E62 11
E62 12
E 6 2 2 0 サーミスタの異常 「1-6-4.E：62：20（サーミスタの異常）が出た場合」を参照。
E 9 1 0 1 フラッシュの充電異常 LEDフラッシュ /ビデオライトまたは充電コンデンサの点検または交換をする。
E 9 1 0 2 LEDビデオライトの異常 LEDフラッシュ /ビデオライトまたは充電コンデンサの点検または交換をする。
E 9 1 0 3 LEDビデオライトの温度検出異常 LEDフラッシュ /ビデオライトまたは充電コンデンサの点検または交換をする。
E92 01
E94 00
E 9 4 0 1 フラッシュメモリ内部異常 フラッシュメモリ（MM-102基板IC8101，IC8201）を点検する。
E 9 4 0 2 BGMデータ異常 CPU（VC-658基板IC1301）を点検する。
E 9 5 0 0 GPSハード異常
9 6 0 0
E
E 9 7 0 0 プロジェクタハード異常 電源を入れ直す。
手振れ補正が効きにくい（PITCH角速
度センサ出力張り付き）
手振れ補正が効きにくい（YAW角速
度センサ出力張り付き）
手振れ補正用ICとマイクロコント
ローラーとの通信異常
Active手振れ補正時の画ゆれが補正
できない
(角速度センサ出力張り付き)
シフトレンズオーバーヒート
(PITCH)
シフトレンズオーバーヒート
(YAW)
(バッテリーの)電流値が最大放電電
流を超えた
フラッシュメモリの書込み/消去動作
不良
地図領域マウント異常
PITCH角速度センサ（LD-297基板SE7501）周辺回路を点検する。
YAW角速度センサ（LD-297基板SE7501）周辺回路を点検する。
手振れ補正回路（LD-297基板IC5601）を点検。
画ゆれ検出角速度センサ(CK-244基板SE7701)周辺回路を点検する。
レンズブロックを交換する（注意3）。
エラーが再度発生する場合は，LD-297基板を交換する。
「1-6-2.E：62：11（シフトレンズオーバーヒート（PITCH））が出た場合」を参照。
「1-6-3.E：62：12（シフトレンズオーバーヒート（YAW））が出た場合」を参照。
バッテリ残量に依存する場合があるので，バッテリ残量を確認する。次にバッ
テリを交換して症状が出るか確認する。バッテリを交換しても症状が出る場合
は，エラー発生後に電源が切れてしまうため，分解して確認する。DCジャッ
ク（J901）をVC-658基板に接続した状態(最小限の接続)でDC／DCコンバータ
(VC-658基板IC4301)の各チャンネル出力を確認する。
フラッシュメモリ（MM-102基板IC8101，IC8201）を点検する。
NX30E/NX30J/NX30N/NX30P/NX30U:
FFC-254フレキシブルフラットケーブルが切れていないか，また完全に挿入さ
れているかを点検する。
フレキシブル基板に問題がない場合は，GP-037基板の点検または交換をする。
NX30E/NX30J/NX30N/NX30P/NX30U:
LD-297基板を点検または交換する。
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
注 意 3： レンズブロックを交換した場 合は，AdjustStationからAdjustManualを起動させて必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-12
Page 17
1-6. シフトレンズエラーの対処方法
– JAPANESE –
1-6-1.E：62：02（手振れ補正用ICの異常）が出た場合
C5636 C5640
C5642 C5643
LD-297 BOARD (SIDE A) LD-297 BOARD (SIDE B)
R5632
IC5601
順序 作業内容
1 電源を切る。
LD-297基板IC5601の周辺にあるR5632の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直後の出力
2
電圧が図2の様に変化することを確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意）。図2の様に変化しないときはカメラコントロール
3
回路（VC-658基板IC1301）周辺を点検する。
注意： レンズブロックを交換した場合 は，AdjustStationからAdjustManualを起動させて必要な調整項目を実施すること。
調整後はにして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-6-2.E：E:62:11（シフトレンズオーバーヒート（Pitch）がでた場合
順序 AdjustBlock AdjustCode 作業内容
1
2
3
4
5 電源を切る。
6
7
注 意： レンズブロックを交換した場合は，AdjustStationからAdjustManualを起動させて必要な調整項目を実施すること。
調整後は手ぶれ補正ONの状態にして、手持ち動作で手ぶれ補正が適正に効いていることを確認すること。
AdjustStationからAdjustManualを起動させて、[SERVICE]タブにある[Measureto
E:62:11/12]を実施する。
順序１を実行した後にシフトレンズが動いているか確認する。
もしシフトレンズが動かない場合はレンズブロックを交換する。
動く場合は順序3に進む。
LD-297基板のIC5601周辺にあるC5642とC5643の出力電圧をオシロスコープで測定する。
順序1を実行したときに出力電圧が変化することを確認する
出力電圧が変化しないときはレンズブロックを交換する（注意）。
変化する場合は順序5へ進む。
LD-297基板のIC5601周辺にある，R5632の出力電圧をオシロスコープで測定しながら電源
を入れる。
電源投入直後の出力電圧が図2の様に変化することを確認する。
出力電圧が3Vに立ち上がったときはレンズブロックを交換する。
立ち上がらない場合はVC-658基板のIC1301とLD-297基板のIC5601の回路周辺を点検す
る。
図1.LD-297基板測定箇所
約 330 msec
注：Lowの区間の長さは場合によって多少異なる
図2.LD-297基板R5632の出力電圧の変化
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-13
Page 18
1-6-3.E:62:12（シフトレンズオーバーヒート（Yaw）がでた場合
– JAPANESE –
1-7. GPS受信確認(NX30E/NX30J/NX30N/NX30P/NX30U)
順序 AdjustBlock AdjustCode 作業内容
1
2
3
4
5 電源を切る。
6
7
注 意： レンズブロックを交換した場合は、必要な調整項目を実施すること
調整後は手ぶれ補正ONの状態にして、手持ち動作で手ぶれ補正が適正に効いていることを確認する
AdjustStationからAdjustManualを起動させて、[SERVICE]タブにある[Measureto
E:62:11/12]を実施する。
順序１を実行した後にシフトレンズが動いているか確認する。
もしシフトレンズが動かない場合はレンズブロックを交換する。
動く場合は順序3に進む。
LD-297基板のIC5601周辺にあるC5636とC5640の出力電圧をオシロスコープで測定する。
順序1を実行したときに出力電圧が変化することを確認する
出力電圧が変化しないときはレンズブロックを交換する。
変化するときは手順5へ進む。
LD-297基板のIC5601周辺にある，R5632の出力電圧をオシロスコープで測定しながら電源
を入れる。
電源投入直後の出力電圧が図2の様に変化することを確認する。
出力電圧が3Vに立ち上がったときはレンズブロックを交換する。
立ち上がらないときはVC-658基板のIC1301とLD-297基板のIC5601の回路周辺を点検する
1-6-4.E：62：20（サーミスタの異常）が出た場合
順序 作業内容
1 電源を入れる。
2 レンズブロックとLD-297基板間のフレキシブルフラットケーブルとコネクタの接続を確認する。
3 接続に異常がなければレンズブロックを交換する（注意）。交換してもエラーが発生する場合はLD-297基板を交換する。
部品交換やセット組み立て後は，GPS信号受信確認を行います。
GPS機能確認方法
空の開けた場所で，GPSを「ON」にすると， が表示され，測位準備が行われます。
測位できた場合，動画・静止画の撮影時に位置情報を記録します。
•GPS衛星からの電波の受信状況によって画面に表示されるアイコンが変わります。
注意： レンズブロックを交換した場合 は，AdjustStationからAdjustManualを起動させて必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
• 測位中になるまで数分かかることがあります。
本機を「地図データの使用許諾に同意するかを確認するメッセージが表示される状態」に戻したい場合は，AdjustmentManualの
SERVICEタブにある内容に従って設定してください。
GPSアシストデータを使う
付属のソフトウェア「PlayMemories Home」でGPSアシストデータを本機に取り込むと、位置情報を取得するまでの時間を短くするこ
とができます。
インターネットに接続された状態でパソコンと本機をつないでください。自動的にGPSアシストデータが更新されます。
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-14
Page 19
1-8. LEDフラッシュ／ビデオライトの放電について
– JAPANESE –
プロジェクターの不具合確認手順（明るさに関する指摘の場合）
この機種ではLEDを使用したLEDフラッシュ／ビデオライトを使用しております。
そのため高電圧部分が無く，放電は不要です。
1-9.プロジェクターユニット交換時の注意
プロジェクター投影機能のサービス、点検時には下記のフローを参照してください。
お客様よりプロジェクター投影機能に関する指摘を受けた場合は、下記のフロー沿って不具合箇所を確認してください。
その確認結果に従って、修理を行ってください。
注意1：プロジェクターを 使用した後は，プロジェクターユニットが熱くなっています。
特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行ってください。
注意2：プロジェクターのレンズ表面についた汚れは、メガネ拭きやクリーニングクロス等の柔らかい布で軽く拭いてください。
汚れがひどいときは、メガネ拭きやクリーニングクロス等の柔らかい布に水を少し含ませて、拭きとってください。
アルコールやベンジン、シンナー、酸性洗浄液、アルカリ性洗浄液、研磨剤入り洗浄剤、化学ぞうきん等は
レンズ表面を傷めますので、絶対に使用しないでください。
プロジェクターの不具合確認手順（明るさに関する指摘以外の場合）
プロジェクター不具合の
指摘品受付
1 Adjust manualのADJUSTタブを参照
2 Adjust manualのSERVICEタブを参照
明るさに
関する指摘
Yes
No
B
プロジェクター不具合の
指摘品受付
明るさに
関する指摘
Yes
明るさの測定
( 2)
OK
No
NG
B
A
1 Adjust manualのADJUSTタブを参照
2 Adjust manualのSERVICEタブを参照
・
プロジェクターユニット（LED発光部）を交換する (*1)
・
PJ基板を交換する(*1)
・
プロジェクターユニット（LED発光部）とPJ基板の
両方を交換する(*1)
Projector Data Input
・
Fixed valueの入力
ユニット上の貼付シールに記載されている番号を入力
・
シリアルNoの入力
LD40Syywwnnnn 赤字部分の入力
Projector LED
検査 ( 1)
NG
明るさの測定
( 2)
OK OK
修理完了
NG
A
Projector LED
検査 ( 1)
NG
・
プロジェクターユニット（LED発光部）を交換する (*1)
・
PJ基板を交換する(*1)
・
プロジェクターユニット（LED発光部）とPJ基板の
両方を交換する(*1)
Projector Data Input
・
Fixed valueの入力
ユニット上の貼付シールに記載されている番号を入力
・
シリアルNoの入力
LD40Syywwnnnn 赤字部分の入力
Projector LED
検査 ( 1)
OK
NG
修理完了
OK
明るさの測定
( 2)
OK
NG
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-15
Page 20
1-10.キャビネット（底）交換時の注意
1-10-1. キャビネット（底）注文時の注意
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット（底）は機種により異なります。
該当するものを選んで注文してください。
注意：キャビネット（底）交換後はシリアルナンバーがサービス
専用のシリアルナンバーに変更されます。お客様への案
内と修理データのシリアルナンバー変更を行ってくださ
い。
– JAPANESE –
1-10-2. HXR-NX30Jのキャビネット（底）ASSY交換時の注意
交換前のキャビネット（底）に印字されている“製造年（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（底）に貼付けて
ください。
例：下図では，“12”のラベルを貼る
*ラベルはサービス用キャビネット(底)に同梱されておらず，個別に供給となります。
ラベルが必要なときは，4-424-330-01を注文してください。
HXR-NX30J
シリアルナンバー シリアルナンバー シリアルナンバー
Part No. Description
A-1889-063-A CABINET (BOTTOM)
HXR-NX30P
シリアルナンバー
Part No. Description
A-1889-066-A CABINET (BOTTOM)
HXR-NX30U
Part No. Description
A-1889-064-A CABINET (BOTTOM)
HXR-NX30E
シリアルナンバー シリアルナンバー
Part No. Description
A-1889-067-A CABINET (BOTTOM)
HXR-NX30NHXR-NX30J
Part No. Description
A-1889-065-A CABINET (BOTTOM)
HXR-NX30C
Part No. Description
A-1889-068-A CABINET (BOTTOM)
* 製造年月
*
ラベルを貼付けてください。
1-10-3. HXR-NX30Uのキャビネット（底）交換時の注意
交換前のキャビネット（底）に印字されている“製造年月（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（底）に貼付け
てください。
例：下図では，“2B”のラベルを貼る
*ラベルはサービス用キャビネット(底)に同梱されておらず，個別に供給となります。
ラベルが必要なときは，4-415-879-01を注文してください。
HXR-NX30U
* 製造年月
*
ラベルを貼付けてください。
1-10-4. HXR-30Nのキャビネット（底）交換時の注意
交換前のキャビネット（底）に印字されている“製造年月（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（底）に貼付け
てください。
例：下図では，“2012-05”のラベルを貼る
*ラベルはサービス用キャビネット(底)に同梱されておらず，個別に供給となります。
ラベルが必要なときは，4-424-330-01を注文してください。
HXR-NX30N
* 製造年月
* ラベルを貼付けてください。
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-16E
Page 21
2. REPAIR PARTS LIST
IDENTIFYING PARTS
Follow the disassembly in the numerical order given.
1 XLR Section
• HN-003 Board
• XL-013 Board
• Control Switch Block (AU91000)
6 L Cover
3 Cabinet (L)
qa Cabinet (F) Block
• FR-319 Board
• FP-1518 Flexible Board
Assy
Assy
qf Lens Block
• CM-121 Board
5 Cabinet (Top) Block
qd LD-297 Board
2 MM-102 Board
7
EVF Block
q; VC-658 Board
8 Battery Block
9 RH-014 Board
qs Cabinet (R) Block
• CK-244 Board
• GP-037 Board
• PD-465 Board
• PJ-104 Board
• FP-1519 Flexible Board
• FP-1521 Flexible Board
• FP-1554 Flexible Board
• FP-1582 Flexible Board
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: F
• COILS
uH: H
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: , for example:
uA...: A... , uPA... , PA... ,
uPB... , PB... , PC... , PC... ,
uPD..., PD...
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いてい
る部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異なる場合があります。
•*印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA...,uPA...,uPB...,uPC...,uPD...等はそれぞれμA..., μPA...,μPB...,
μPC...,μPD...を示します。
･ Abbreviation
CH : Chinese model
CND : Canadian model
J : Japanese model
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
お願い
図面番号で部品を指定するときは基板名
又はブロックを併せて指定してください。
印の部品，または0印付の点線で囲ま
0
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。
• 外装部品色表示
例：
(SILVER)：セットの色を表す。
(Silver) ：部品の色を表す。
View Position
Left View
Top View
Back View
1 Cabinet (Bottom)
Link
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Right View
Front View
4 Hinge Cover (R)
Bottom View
ACCESSORIES ASSEMBLY
2-1
Page 22
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible
that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
– ENGLISH –
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け，折れ等
がないことを確認する。
また，コネクタへの接続は，差し込み不足や斜め差しにならないよ
うに注意する。
• コネクタを取り外す時に，線材部（極細）を持って引っ張ると断線す
る恐れがありますので，絶対に線材部（極細）を持って引っ張らない
でください。
• 線材部（極細）を押さえながらコネクタを差し込むと，線材部（極細）
が断線する恐れがありますので，絶対に線材部（極細）には負担をか
けないでください。
• 金メッキされているフレキシブル基板には，強い負担をかけないで
ください。
– JAPANESE –
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-2
Page 23
2-1. EXPLODED VIEWS
DISASSEMBLY
2-1-1. OVERALL SECTION-1
ns: not supplied
4 (Claws)
#2
Do not hold lens unit.
4 (Claws)
#1
4 6
XLR Section
(See page 2-11)
Overall Section-2
(See page 2-4)
#2
5 (Claws)
1. Remove in numerical order (1 to 5) in the left figure.
1 #113 X 7
Bottom View
#113
#113
2 #1 X 1
4 #1 X 2 → #2 X 1
Bottom View Left View
#1
Bottom View
#2
3 #3 X 1
#1
5
Open the LCD (5-1) → #2 X 4 → Rotate the LCD (5-2)
Right View Back View
#2
Bottom View
#3
#2
5-1
2
5 7
#2
3 5
1
#3
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
#1
2 4
ns
#1
3
1
1
(Note)
2
2
#113
Note
5-2
#113: M1.7 X 5.0
(Black)
2-635-562-41
1.7
5.0
Ref. No. Part No. Description
1 (Note) CABINET (BOTTOM)
2 2-589-376-01 FOOT (395), RUBBER
3 3-283-643-01 SCREW, TRIPOD
4 4-422-371-01 FRAME, CABINET (BM)
5 A-1878-202-A MM-102 BOARD, COMPLETE (SERVICE) (96G)
6 X-2584-155-1 CABINET (L) ASSY
7 4-422-364-01 COVER (R (390)), HINGE
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
#1 2-635-562-11 SCREW (M1.7)
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#113 2-635-562-41 SCREW (M1.7)
2-3
Note: Refer to page 1-8 “Precaution on replacing the Cabinet
Note:
(Bottom)” when changing the Cabinet (Bottom).
キャビネットボトム組立の交換時は、1-16ページの“キャ
ビネット(底）交換時の注意”を参照してください。
Page 24
DISASSEMBLY
2-1-2. OVERALL SECTION-2
52
MIC901
51
53
#273
(Note 1)
56
2 58
#273
(Note 1)
#2
#1
#113
3 (Claw)
#1
55
1 (Claws)
54
#3
1 57
3 59
#2
Claws
#3
64
#2
61
LCD902
63 (Note 2)
4 60
62
#12
#12
1. Remove in numerical order (1 to 4) in the left figure.
1
Open and rotate the LCD (1-1) → #2 X 2 → Pull out the EVF (1-2) → #2 X 2 → #113 X 1
#2
#2
1-1
2 Bring up the EVF (2-1) → #1 X 2 → Open the DC lid (2-2)
Back View
2-1
4
#2 X 2 → #3 X 2 → #2 X 1
#1
Top View
2-2
Bottom View
#1
Back View
#2
1-2
#113
Left ViewRight View Bottom View
#2
3 #3 X 2
Top View
#3
BT Panel Section
(See page 2-5)
Ref. No. Part No. Description
51 4-431-867-01 INSULATOR (912), MICROPHONE
52 4-431-866-01 SCREEN (912), WIND
53 4-282-387-01 SHOE, COLD
54 4-282-388-01 SPRING, COLD SHOE
55 4-431-864-01 CABINET (912), MICROPHONE
56 4-431-865-01 GRILLE (912), MICROPHONE
57 X-2584-852-1 CABINET (TOP (912)) ASSY (GPS Model)
57 X-2584-853-1 CABINET (TOP (912N)) ASSY (Non GPS Model)
58 X-2584-164-1 COVER ASSY, L
59 1-489-964-21 SWITCH BLOCK, CONTROL (PS39900)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
#2
#2
Ref. No. Part No. Description
60 X-2584-162-1 EYE CUP ASSY
61 X-2584-161-1 FRAME ASSY, VF
62 4-422-351-01 RETAINER, VF HOLDER
63 1-471-577-11 MAGNET (HOLE SENSOR) (Note 2)
64 4-422-367-01 BASE, VF
LCD902 1-811-013-11 LCD MODULE (FL0906)
MIC901 1-542-917-11 MICROPHONE UNIT
#1 2-635-562-11 SCREW (M1.7)
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#12 3-080-204-21 SCREW, TAPPING, P2
#113 2-635-562-41 SCREW (M1.7)
#273 2-342-356-21 SCREW (M2 (ECO, EG)) (Note 1)
2-4
#2
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2.5
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
5.0
#3
1.7
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
#113: M1.7 X 5.0
(Black)
2-635-562-41
4.0
5.0
1.7
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
#273: M2.0 X 6.0
(Black)
2-342-356-21
6.0
2.5
1.7
Note
Note 1: This screw cannot be re-used. Discard the screw once
Instead, use a new screw.
Note 1:
2.0
removed for repair.
このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじ
と交換してください。
Note 2:
Install the magnet with
the marking oriented
as shown below.
Note 2:
マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
ください。
Marking
マ−キング
Page 25
DISASSEMBLY
2-1-3. BT PANEL SECTION
102
103
1
104
105
#1
#3#1
2 (Claws)
107
#11
109
115
108
#2
110
112
113
J901
4
114
#2
1. Remove in numerical order (1 to 4) in the left figure.
1 #3 X 3
Top View
#3
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
1.7
4.0
(Red)
2-660-401-01
2.5
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
4.0
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
1.7
5.0
101
3
(Note 1)
2
106
(Note 2)
3 (Claw)
Main Board Section
(See page 2-6)
Ref. No. Part No. Description
101 4-422-368-01 RETAINER, USB ARM (Note 1)
102 1-818-890-11 CONNECTOR, EXTERNAL (HOT SHOE)
103 4-422-360-01 FRAME, HS
104 4-422-369-01 SHEET, FLEXIBLE GUARD
105 1-885-106-11 FP-1523 FLEXIBLE BOARD
#12
Ref. No. Part No. Description
111 4-422-337-01 FRAME, BT
112 4-422-338-01 RETAINER, DC
113 2-590-635-01 TAPE (AS 1/2)
114 X-2584-160-1 PANEL ASSY, BT
115 4-273-783-11 WASHER (MS)
111
Note
Note 1: Refer to “Assembly-1: Installation Cautions of the USB Arm
Note 1:
Note 2: Refer to “Assembly-2: Installation Cautions of the VF Flexible
Note 2:
Retainer.”.
“Assembly-1:InstallationCautionsoftheUSBArmRetainer.”
を参照してください。
Guard.”.
“Assembly-2:Installation CautionsoftheVFFlexible Guard.”
を参照してください。
106 4-422-361-01 GUARD, VF FLEXIBLE (Note 2)
107 X-2584-854-1 BELT (G) ASSY, 12 TYPE GRIP
108 1-838-712-21 CABLE, BUILT-IN USB
109 4-422-339-01 GUARD, BELT
110 4-422-340-01 SHEET METAL (R), BELT
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
J901 1-822-470-22 JACK, DC
#1 2-635-562-11 SCREW (M1.7)
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
2-5
Page 26
DISASSEMBLY
A
2-1-4. MAIN BOARD SECTION
: BT7001 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-44)
153
2
A
#3
157
156
158
#3
VC-658
Lens Section
(See page 2-7)
B
1. Remove in numerical order (1 to 5) in the left figure.
1 #3 X 3
Back View
#3
3 #3 X 2
Back View Bottom View
#3
Screw
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
#3
5 #3 X 3
Back View
#3
BT7001
(Note 1)
B
BH7001
(Note 1)
A
C7207
(Note 2)
Ref. No. Part No. Description
151 A-1871-741-A RH-014 BOARD, COMPLETE
152 4-422-365-01 HOLDER (L), JACK
153 4-422-359-01 HEAT SINK (B), VC
154 4-425-108-01 SHEET (A), RADIATION
155 4-422-357-01 FRAME, RH
#3
RH-014
1
#11
151
154
152
3
155
5
160
2 (Claws)
159
#3
161
4
(Note 3)
Ref. No. Part No. Description
161 4-422-362-01 GUARD, CM FLEXIBLE (Note 3)
BH7001 1-251-928-21 HOLDER, BATTERY (Note 1)
BT7001 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
C7207 1-116-781-11 DOUBLE LAYERS 350 uF 5.5V (Note 2)
Note
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
:
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は、取扱指示に従って処分してください。
Note 1: Replace the battery holder (BH7001) together when replac-
When mounting these parts, mount new battery holder first
Note 1:
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は、先にバッテリホルダを取り付けてか
ing the lithium storage battery (BT7001) on the RH-014
board. (The battery holder removed once cannot be usedagain.)
and attach new lithium storage battery next.
RH-014基板のリチウム蓄電池(BT7001) を交換する場合は
バッテリホルダ(BH7001)も同時に新品に交換してくださ
い。
らリチウム蓄電池を装着してください。
注意
Note 2: This model is provided with a flash unit using LED Flash/
Therefore, the LED Flash/Video light (C7207) does not
Note 2:
そのため高電圧部分が無く、放電は不要です。
Note 3: Refer to “Assembly-3: Installation Cautions of the CM Flexible
Note 3:
Video light (C7207).
have high voltage part and does need to be discharged.
この機種ではLEDを使用したLEDフラッシュ /ビデオライト
(C7207)を使用しております。
Guard.”.
“Assembly-3:InstallationCautionsoftheCMFlexible
Guard.”を参照してください。
156 4-422-370-01 SHEET, CM FLEXIBLE GUARD
157 1-885-105-11 FP-1522 FLEXIBLE BOARD
158 4-432-696-01 SHEET, RH FLEXIBLE GUARD
159 1-885-623-21 FP-1557 FLEXIBLE BOARD
160 A-1885-417-A VC-658 BOARD, COMPLETE (SERVICE)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#11 3-078-890-11 SCREW, TAPPING
2-6
Page 27
Ver. 1.1 2012.06
The changed portions from
Ver. 1.0 are shown in blue.
DISASSEMBLY
2-1-5. LENS SECTION
#3
Cabinet (F) Section
1
(See page 2-8)
#2
205
(including IC6701
(CMOS imager))
(Note 1)
204
203
#12
206
(Note 2)
#3
207
211
#3
210
#3
209
5
#3
#3
208
4
212
2 (Bosses)
#3
2
213
214
1. Remove in numerical order (1 to 6) in the left figure.
1 #3 X 1 → #2 X 1
Top View Right View
#3
3 #3 X 1 → #2 X 1
Front View Right View
#3
5 #3 X 6
Back View Left View Top View Bottom View
#2
#2
4 #3 X 3
Back View
#3
#3
202
6
201
(Note 3)
Refer to "Caution for Handling
the Lens Device (LSV-1550A-BI)"
Ref. No. Part No. Description
201 4-422-372-01 ORNAMENT, LENS (Note 3)
202 A-1898-068-A SERVICE, LSV-1550A-BI
203 1-856-033-21 OPTICAL FILTERBLOCK (OFB-03-52)
204 3-216-044-01 RUBBER (1270), SEAL
205 A-1785-655-A CMOS BLOCK ASSY (1390) -077 (including IC6701
(COMS Imager)) (Note 1)
206 4-422-373-01 SHEET, CM RADIATION (Note 2)
207 4-422-356-01 FRAME, LD
208 4-422-355-01 FRAME, VC
209 1-885-375-11 FP-1550 FLEXIBLE BOARD
210 4-425-581-01 SHEET (A), SHIELD
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
#3
Cabinet (R) Section
3
(See page 2-9)
Ref. No. Part No. Description
211 1-885-376-11 FP-1551 FLEXIBLE BOARD
212 A-1889-556-A LD-297 BOARD, COMPLETE
213 4-422-358-01 HEAT SINK (A), VC
214 4-281-952-01 SHEET (B), VC RADIATION
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#12 3-080-204-21 SCREW, TAPPING, P2
#2
2-7
#3 #3 #3
Screw
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
Note
Note 1: Be sure to read “Precautions for Replacement of Imager” on
Note 2: The CM Radiation Sheet when peeling off once, so that it
Note 3: Refer to “Assembly-4: The Method of removing of Lens
page 6-1 when changing the imager.
cannot be reused.
Ornament.”.
5.0
1.7
Note 1:
Note 2:
Note 3:
イメージャの交換時は6-1ページ、“イメージャ交換時の注
意”を必ずお読みください。
CMRadiationSheetは一度剥がすと粘着力が弱くなるため、
再利用はしないでください。
“Assembly-4:TheMethodofremovingofLensOrnament.”
を参照してください。
Page 28
Screw
2-1-6. CABINET (F) SECTION
A
251
252
253
254
258
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
4.0
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
1.7
5.0
B
255
#3
#11
#11
C
259
256
#3
A
#12
257
C
B
Ref. No. Part No. Description
251 1-489-963-11 SWITCH BLOCK, CONTROL (RS39900)
252 X-2584-148-1 CABINET (F) ASSY
253 A-1865-250-A BARRIER_UNIT, LENS
254 A-1872-023-A LED BLOCK ASSY, ST
255 4-422-248-01 FRAME (LOWER), F
256 4-422-247-01 FRAME (UPPER), F
257 A-1871-872-A FR-319 BOARD, COMPLETE
258 4-424-924-01 CUSHION, ST
259 1-885-101-11 FP-1518 FLEXIBLE BOARD
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
2-8
Page 29
Screw
2-1-7. LCD SECTION-1
ns: not supplied
319
#11
320
#3
#211
(Note 1)
321
(Size: 5.0mm X 10.0mm)
(Note 3)
304
#2
Claws
302
#11
Claws
303
302
GPS Model
301
Claws
Ref. No. Part No. Description
301 X-2584-847-1 CABINET (C (912)) ASSY, P
302 4-272-357-01 GASKET (P (389))
303 4-422-327-01 HEAT SINK, P
304 4-272-356-01 INSULATING SHEET (P (389))
305 4-272-354-01 SHEET, P RADIATION
306 A-1861-092-A GP386 ASSY (GPS Model)
307 1-838-558-11 CABLE, FLEXIBLE FLAT (FFC-254) (GPS Model)
308 4-271-688-01 CUSHION (M)
309 4-272-358-01 CUSHION, P
310 A-1876-774-A E2T 0.2 PICO OPTICAL ENGINE (Note 2)
311 X-2584-302-1 ASSY COVER MODULE E2T
312 4-411-285-01 FOCUS LEVER V2 FLT3
313 4-411-284-01 SCREW CALD TAP BLACK
314 A-1872-028-A FP-1582 FLEXIBLE BOARD, COMPLETE
315 A-1872-021-A PJ-104 BOARD, COMPLETE
Claws
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
309
LCD Section-2
318
(See page 2-10)
317
310
305
311
Claws
(Note 2)
Claw
312
ns
315
313
Adjust the position.
308
314
307
#30
#3
306
GPS Model
Ref. No. Part No. Description
316 4-425-582-01 SHEET (GPS), SHIELD (GPS Model)
317 X-2584-850-1 CABINET (R (912)) ASSY
318 A-1871-876-A CK-244 BOARD, COMPLETE
319 1-885-104-11 FP-1521 FLEXIBLE BOARD
320 A-1871-880-A FP-1554 FLEXIBLE BOARD, COMPLETE
321 2-649-300-01 SHEET, ADHESIVE (Note 3)
#2 2-635-562-31 SCREW (M1.7)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2
#11 3-078-890-11 SCREW, TAPPING
#30 3-086-156-11 SCREW B1.2
#211 2-187-345-01 SCREW (M1.7), P2 (Note 1)
GPS Model
316
2-9
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
Note
Note 1: This screw cannot be re-used. discard the screw removed
In-stead, use a new screw.
Note 1:
サービス対応時に一度でも外した場合は新品のねじと交換
プロジェクターを使用した後は，プロジェクターユニットが熱く
なっています。特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行なって
ください。
once in servicing.
このねじは再利用することができません。
してください。
Note 2:
Do not hold the following part.
Lens
Very weak
Copper Plate
Very weak
Sheet
Very weak
Sheet
Very weak
The projector unit (copper plate in particular) becomes hot
after it is used.
When replacing a part of the projector unit, wait until it is
cooled down.
Note 2:
持ってはいけない部分
レンズ
非常に弱い部分
シート
非常に弱い部分
銅板
非常に弱い部分
シート
非常に弱い部分
4.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
1.7
Note 3:
Note 3:
Cut SHEET, ADHESIVE (2-649-300-01) into
the desired length and use it.
FP-1519
Flexible Board
SHEET, ADHESIVE (2-649-300-01)は指定の
サイズに切って使用すること。
FP-1519
Flexible Board
3.5
1.2
10.00mm
10.00mm
#211: M1.7 X 2.5
(Black)
2-187-345-01
5.00mm
5.00mm
1.7
2.5
Page 30
Screw
2-1-8. LCD SECTION-2
366
(Note 2)
Claws
365
364
362
363
(Note 1)
#1
361
LCD901
359
360
#1: M1.7 X 2.5
(Black)
2-635-562-11
Note
Note 1:
Install the magnet with
the marking oriented
as shown below.
2.5
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
Note 1:
マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
ください。
#11
SP901
353
354
353
352
351
Ref. No. Part No. Description
351 4-271-688-01 CUSHION (M)
352 4-422-321-01 HOLDER (390), SP
353 4-422-328-01 CUSHION, SP HOLDER
354 A-1852-433-A PD-465 BOARD, COMPLETE (GPS Model)
354 A-1852-434-A PD-465 BOARD, COMPLETE (Non GPS Model)
355 4-408-193-01 INSULATING SHEET (PD (385))
356 4-422-319-02 RETAINER (390), LCD
357 4-209-805-01 CUSHION, LCD (Note 3)
358 4-265-596-11 SHEET (BL)
359 4-422-317-01 PLATE (P (390)), GROUND
SP902
355
357
(Note 3)
358
356
Ref. No. Part No. Description
365 4-422-323-01 COVER (O (390)), HINGE
366 1-885-102-11 FP-1519 FLEXIBLE BOARD (Note 2)
LCD901 1-811-305-11 PANEL, TOUCH (TP-SZ814AMD1)
SP901 1-858-528-51 SPEAKER (2-1CM)
SP902 1-858-528-51 SPEAKER (2-1CM)
#1 2-635-562-11 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
Marking
Note 2: Refer to “Assembly-5: The Method of attachment of FP-1519
Note 2:
Note 3: Refer to “Assembly-6: Installation Cautions of LCD Cushion.”.
Note 3:
Flexible Board.”.
“Assembly-5:TheMethodofattachmentofFP-1519
FlexibleBoard.”を参照してください。
“Assembly-6:InstallationCautionsof LCD Cushion.”を参照
してください。
マーキング
360 4-422-315-01 CABINET (M (390)), P
361 4-422-326-01 KNOB, FOCUS
362 4-422-325-01 COVER (U (390)), HINGE
363 1-471-573-11 MAGNET (Note 1)
364 X-2582-799-1 HINGE Y(P) ASSY, T STYLE
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-10
Page 31
Screw
2-1-9. XLR SECTION
ns: not supplied
402
404
#119
403
405
406
#119
#49
ns
#53
#49
ns
402
#49
403
401
411
413
412
414
#49
424
416
423
ns
#49
415
417
2.0
#119: M2.6 X 5.0
(Black)
7-627-556-58
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
2.0
5.0
Note
Note: XLR LABEL is not included in XLR UNIT BLOCK ASSY.
When the XLR UNIT BLOCK ASSY has been replaced, attach
Note:
the XLR LABEL of the relevant model.
XLRUNITBLOCKASSYにはXLRLABELが含まれていませ
ん。
XLRUNITBLOCKASSYを交換した場合は、該当する機種の
XLRLABELを貼り付けること。
2.6
5.0
407
410
408
409
Ref. No. Part No. Description
401 X-2342-570-1 HOLDER (93000) ASSY, MICROPHONE
402 3-284-080-01 RUBBER, MICROPHONE
403 3-284-081-11 SHEET, RUBBER ADHESIVE
404 3-284-621-11 CUSHION, MICROPHONE HOLDER
405 4-119-861-01 RUBBER (93000), HOLDER
406 3-284-075-02 COVER, MICROPHONE HOLDER RUBBER
407 4-282-420-01 COVER, XLR
408 4-165-285-01 COVER, XLR RUBBER
409 A-1825-473-A XL-013 BOARD, COMPLETE
410 4-282-421-01 FRAME, XLR
#53
#53
420
#49
#49
422
Ref. No. Part No. Description
416 X-2581-422-1 KNOB (91000) ASSY, XL
417 X-2581-426-1 HANDLE (91000) ASSY
418 1-838-727-11 CABLE, ENCAPSULATED
419 1-489-370-11 SWITCH BLOCK, CONTROL (AU91000)
420 7-624-106-04 STOP RING 3.0, TYPE -E
421 3-077-768-11 XL SHOE PLATE
422 2-892-095-01 CLAMP, CABLE
423 A-1844-926-A XLR UNIT BLOCK ASSY (SERVICE)
424 3-288-615-02 SPRING, SHOE
425 3-701-690-11 LABEL (MADE IN JAPAN)
421
#49
418
419
425
(Note)
411 1-834-244-11 FLEXIBLE FLAT CABLE (FFC-116)
412 A-1825-472-A HN-003 BOARD, COMPLETE
413 4-283-290-01 SHEET (HN), ABSORBING
414 3-069-286-03 SHOE, ACCESSORY
415 4-282-419-01 CABINET (UPPER), HANDLE
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#53 3-080-206-21 SCREW, TAPPING, P2
#119 7-627-556-58 SCREW +P 2.6X5
2-11
Page 32
• EXCEPT J MODEL
ACCESSORIES
901 902 903 904 905
• J MODEL
付属品
951 952 953 954 955
906 907 908 909 910
911 (Including 912, 913, 932) 914 915 916
912
913
932
917
Ref. No. Part No. Description
901 1-487-150-92 AC Adaptor
902 1-832-121-31 Power cord (Mains lead) (CH)
902 1-837-482-31 Power cord (Mains lead) (AEP, E)
902 1-838-955-11 Power cord (Mains lead) (US, CND)
903 1-569-008-12 Conversion (2P) Adaptor (E: NTSC)
904 1-839-080-21 HDMI cable
905 1-838-205-11 A/V connecting cable
906 1-838-714-31 USB connection support cable
907 1-837-533-11 USB Adaptor Cable
908 1-487-540-11 Wireless Remote Commander
909 X-2584-166-1 Lens hood
910 X-2584-165-1 Step Down Ring
911 1-542-749-12 Wind Screen, Microphone (ECM-XM1)
912 3-048-481-01 Wind Screen
* 913 3-179-882-01 Microphone Spacer
Ref. No. Part No. Description
914 A-1844-926-A XLR Adaptor
* 915 4-425-005-11 Operating Guide (ENGLISH)
915 4-425-006-11 Operating Guide (ENGLISH)
915 4-425-006-21 Operating Guide (SIMPLIFIED CHINESE)
916 4-425-003-01 CD-ROM “Content Management Utility” (Note 1)
917 4-433-085-01 CD-ROM “Manuals for Digital HD Video Camera
Recorder”
(Note 1)
TheCD-ROMsuppliedcontainsalloflanguageversionofthe
OperatingInstructions(PDF)forprinting.
･Theprintedmatterisnotsupplied.Ifrequired,pleaseorderitwith
thepartnumberbelow.
956 957 958 959 960 (Including 961, 962, 982)
961
962
982
963 964 965 966
Ref. No. Part No. Description
951 1-487-150-92 ACアダプター
952 1-836-110-11 電源コード
953 1-839-080-21 HDMIケーブル
954 1-838-205-11 A/V接続ケーブル
955 1-838-714-31 USB接続サポートケーブル
956 1-837-533-11 USBアダプターケーブル
957 1-487-540-11 ワイヤレスリモコン
958 X-2584-166-1 レンズフード
959 X-2584-165-1 ステップダウンリング
960 1-542-749-12 ウインドスクリーン，マイク(ECM-XM1)
Ref. No. Part No. Description
961 3-048-481-01 ウインドスクリーン
* 962 3-179-882-01 マ イクスペーサー
963 A-1844-926-A XLRアダプター
964 4-425-005-01 取扱説明書
965 4-425-003-01 CD-ROM「ContentManagementUtility」
966 4-433-085-01 CD-ROM「ManualsforDigitalHDVideoCamera
Recorder」
(Note 3)
取扱説明書(PDF)は全ての言語が付属品のCD-ROMに含まれていま
す。
CD-ROM内の取扱説明書(PDF)につきましては印刷しての供給は対応
しておりません。
(Note3)
This item is supplied with the unit as an accessory, but is not prepared as a service part.
931 932
Ref. No. Part No. Description
931 (Not supplied) Rechargeable battery pack NP-FV70
932 (Not supplied) Microphone (Note 2)
(Note 2)
Microphoneisnotsupplied,butthisisincludedin
WindScreen,Microphone(ECM-XM1).
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-12
当商品はアクセサリーとして同梱されておりますがサービス用補修部品としては準備しておりません。
981
Ref. No. Part No. Description
981 (Not supplied) リチャージャブルバッテリーパックNP-FV70
982 (Not supplied) マイク(Note4)
982
(Note 4)
マイクは単体での供給をしていませんが、ウインドスクリーン，
マイク(ECM-XM1)に含まれています。
Page 33
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for
routine service. Some delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded
views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components
used on the set.
• CAPACITORS:
uF: F
• COILS
uH: H
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: , for example:
uA...: A... , uPA... , PA... ,
uPB... , PB... , uPC... , PC... ,
uPD..., PD...
When indicating parts by reference
number, please include the board name.
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Note1 : Be sure to read “Precautions for Replacement of Imager”
on page 6-1 when changing the imager.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 2: Replace the battery holder (BH7001) together when replac-
ing the lithium storage battery (BT7001) on the RH-014
board. (The battery holder removed once cannot be used
again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は,補修用部品であるため,回路図及び
セットに付いている部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異なる場
合があります。
•*印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA...,uPA...,uPB...,uPC...,uPD...等はそれぞれμA...,
μPA...,μPB...,μPC...,μPD...を示します。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
印の部品，または0印付の点線で囲まれた部品は，
0
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してください。
Note1 :
イメージャの交換時は6-1ページの“イメージャ交換時の
注意”を必ずお読みください。
電池の交換は，正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換し
てください。
使用済み電池は，取扱指示に従って処分してください。
Note 2:
RH-014基板のリチウム蓄電池（BT7001）を交換する場合は
バッテリホ ルダ（BH7001）も同時に新品に交換して下さい。
（一度使用したバッテリホルダは再使用できません。）
部品取り付 け の際は ，先にバッテリホルダを取り付 けて か
らリチウム電池を装着して下さい。
注意
2-2. ELECTRICAL PARTS LIST
A-1871-876-A CK-244 BOARD, COMPLETE
*********************
< CAPACITOR >
C7701 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7702 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7703 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C7704 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C7705 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C7706 1-114-411-21 CERAMIC CHIP 0.33uF 10% 6.3V
C7707 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
< CONNECTOR >
CN9001 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P
CN9002 1-816-643-51 FFC/FPC CONNECTOR (LIF) 10P
< DIODE >
* D9001 6-502-462-01 DIODE CL-271SYG-C-TS
* D9002 6-502-462-01 DIODE CL-271SYG-C-TS
< IC >
IC7701 6-707-333-01 IC NJM3230SE7
< COIL >
* L7701 1-481-425-21 INDUCTOR 10uH
< RESISTOR >
R7702 1-218-969-11 METAL CHIP 22K 5% 1/16W
R7703 1-218-969-11 METAL CHIP 22K 5% 1/16W
R7705 1-218-965-11 METAL CHIP 10K 5% 1/16W
* R7706 1-250-523-11 METAL CHIP 15K 1% 1/16W
R7707 1-218-985-11 METAL CHIP 470K 5% 1/16W
R9001 1-218-944-11 METAL CHIP 180 5% 1/16W
R9005 1-218-965-11 METAL CHIP 10K 5% 1/16W
R9006 1-218-989-11 METAL CHIP 1M 5% 1/16W
R9007 1-218-989-11 METAL CHIP 1M 5% 1/16W
R9008 1-218-965-11 METAL CHIP 10K 5% 1/16W
R9010 1-218-953-11 METAL CHIP 1K 5% 1/16W
R9011 1-218-942-11 METAL CHIP 120 5% 1/16W
R9012 1-218-963-11 METAL CHIP 6.8K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB9001 1-234-376-11 RES, NETWORK 2.2K (1005X4)
RB9002 1-234-376-11 RES, NETWORK 2.2K (1005X4)
CK-244 CM-121 FP-1518 FP-1519
Ref. No. Part No. DescriptionRef. No. Part No. Description
A-1785-655-A CMOS BLOCK ASSY (1390)-077
(Not supplied) CM-121 BOARD, COMPLETE
************************
(IC6701 and CM-121 COMPLETE BOARD are not supplied, but they are included in
CMOS BLOCK ASSY (1390)-077.)
< CAPACITOR >
C6701 1-165-887-91 CERAMIC CHIP 0.22uF 10% 6.3V
C6702 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6703 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6704 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C6705 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C6706 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6707 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6708 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6709 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6710 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6711 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6712 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C6713 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6714 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6715 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6716 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6717 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6718 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6719 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6720 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C6728 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6729 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C6736 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C6737 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6738 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
< CONNECTOR >
CN6701 1-821-501-11 CONNECTOR, FPC (ZIF) 51P
< IC >
IC6701 (Not supplied) IC IMX077LHK-13
IC6703 6-715-412-01 IC MM3404A27URE
IC6706 6-714-504-01 IC MM3404A15URE
< RESISTOR >
R6707 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R6708 1-218-953-11 METAL CHIP 1K 5% 1/16W
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-13
< SWITCH >
* S9001 1-786-914-51 SWITCH, TACTILE
* S9002 1-786-914-51 SWITCH, TACTILE
* S9003 1-786-914-51 SWITCH, TACTILE
* S9004 1-786-914-51 SWITCH, TACTILE
* S9005 1-786-914-51 SWITCH, TACTILE
S9006 1-798-119-11 SWITCH, TACTILE
< SENSOR >
SE7701 1-479-022-81 SENSOR, ANGULAR VELOCITY
1-885-101-11 FP-1518 FLEXIBLE BOARD
********************
1-885-102-11 FP-1519 FLEXIBLE BOARD
********************
Page 34
FP-1521 FP-1522 FP-1523 FP-1550 FP-1551 FP-1554 FP-1555 FP-1557 FP-1582 FR-319 GP-037 HN-003 LD-297
Ref. No. Part No. Description
1-885-104-11 FP-1521 FLEXIBLE BOARD
********************
1-885-105-11 FP-1522 FLEXIBLE BOARD
********************
1-885-106-11 FP-1523 FLEXIBLE BOARD
********************
1-885-375-11 FP-1550 FLEXIBLE BOARD
********************
1-885-376-11 FP-1551 FLEXIBLE BOARD
********************
A-1871-880-A FP-1554 FLEXIBLE BOARD, COMPLETE
*******************************
< CAPACITOR >
C001 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
< SENSOR >
* SE001 1-487-118-11 GMR SENSOR
A-1872-023-A LED BLOCK ASSY, ST
(Not supplied) FP-1555 FLEXIBLE BOARD
*********************
< DIODE >
Ref. No. Part No. Description
< CAPACITOR >
C9601 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C9603 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C9604 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
< CONNECTOR >
CN9601 1-779-330-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 12P
CN9602 1-779-327-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 6P
CN9603 1-784-650-21 CONNECTOR 2P
< DIODE >
D9601 6-503-474-01 DIODE SML-J13RWT96
D9602 6-502-193-01 DIODE SML-D12V8WT86SN
< IC >
IC9601 6-600-629-01 IC RS-470
< TRANSISTOR >
Q9601 (Not supplied) TRANSISTOR DSC500200L
< RESISTOR >
R9601 1-218-953-11 METAL CHIP 1K 5% 1/16W
R9602 1-218-937-11 METAL CHIP 47 5% 1/16W
R9603 1-216-801-11 METAL CHIP 22 5% 1/10W
R9604 1-216-800-11 METAL CHIP 18 5% 1/10W
R9605 1-218-949-11 METAL CHIP 470 5% 1/16W
R9606 1-218-941-81 METAL CHIP 100 5% 1/16W
R9607 1-218-941-81 METAL CHIP 100 5% 1/16W
A-1861-092-A GP386 ASSY (GPS Model)
(Not supplied) GP-037 BOARD, COMPLETE
**********************
(All mounted parts and GP-037 COMPLETE BOARD are not supplied, but they are
included in GP386 ASSY.)
C1017 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1018 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
* C1101 1-100-735-91 CERAMIC CHIP 10uF 20% 4V
* C1102 1-100-735-91 CERAMIC CHIP 10uF 20% 4V
C1103 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1104 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1105 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C1106 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1107 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1108 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C1109 1-100-672-11 CERAMIC CHIP 10uF 20% 16V
C1110 1-114-238-91 CERAMIC CHIP 22uF 20% 10V
C1111 1-114-238-91 CERAMIC CHIP 22uF 20% 10V
C1112 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1113 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1114 1-165-897-11 TANTAL. CHIP 22uF 20% 10V
C1115 1-165-897-11 TANTAL. CHIP 22uF 20% 10V
C1116 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1117 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1118 1-114-238-91 CERAMIC CHIP 22uF 20% 10V
C1119 1-114-238-91 CERAMIC CHIP 22uF 20% 10V
C1120 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1121 1-165-897-11 TANTAL. CHIP 22uF 20% 10V
C1122 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1123 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1124 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1125 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1126 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1128 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C1129 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
< CONNECTOR >
CN1001 1-816-655-61 CONNECTOR, FFC/FPC 8P
CN1101 1-770-625-21 PIN, CONNECTOR 8P
CN1102 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P
CN1103 1-816-650-51 FFC/FPC CONNECTOR (LIF) 24P
Ref. No. Part No. DescriptionRef. No. Part No. Description
< RESISTOR >
R1001 1-216-806-11 METAL CHIP 56 5% 1/10W
R1002 1-218-949-11 METAL CHIP 470 5% 1/16W
R1008 1-218-446-11 METAL CHIP 1 5% 1/10W
R1010 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R1011 1-218-941-81 METAL CHIP 100 5% 1/16W
R1013 1-218-978-11 METAL CHIP 120K 5% 1/16W
R1014 1-208-709-11 METAL CHIP 12K 0.5% 1/16W
R1019 1-218-446-11 METAL CHIP 1 5% 1/10W
R1101 1-218-969-11 METAL CHIP 22K 5% 1/16W
R1102 1-218-969-11 METAL CHIP 22K 5% 1/16W
R1103 1-218-977-11 METAL CHIP 100K 5% 1/16W
R1104 1-218-941-81 METAL CHIP 100 5% 1/16W
R1105 1-218-977-11 METAL CHIP 100K 5% 1/16W
R1106 1-218-941-81 METAL CHIP 100 5% 1/16W
R1109 1-218-971-11 METAL CHIP 33K 5% 1/16W
R1110 1-245-604-11 METAL CHIP 10M 5% 1/16W
R1111 1-245-604-11 METAL CHIP 10M 5% 1/16W
R1114 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W
R1115 1-208-898-81 METAL CHIP 3K 0.5% 1/16W
R1116 1-208-898-81 METAL CHIP 3K 0.5% 1/16W
R1117 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W
R1125 1-218-965-11 METAL CHIP 10K 5% 1/16W
R1126 1-218-965-11 METAL CHIP 10K 5% 1/16W
R1149 1-218-967-11 METAL CHIP 15K 5% 1/16W
R1150 1-218-967-11 METAL CHIP 15K 5% 1/16W
R1151 1-218-965-11 METAL CHIP 10K 5% 1/16W
R1154 1-218-953-11 METAL CHIP 1K 5% 1/16W
R1157 1-218-953-11 METAL CHIP 1K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB1001 1-234-379-21 RES, NETWORK 22K (1005X4)
RB1002 1-234-381-11 RES, NETWORK 100K (1005X4)
RB1003 1-234-381-11 RES, NETWORK 100K (1005X4)
RB1004 1-234-381-11 RES, NETWORK 100K (1005X4)
RB1005 1-234-377-21 RES, NETWORK 4.7K (1005X4)
D0001 6-503-445-01 DIODE CL773SCW02SDWT
D0002 6-503-445-01 DIODE CL773SCW02SDWT
< THERMISTOR >
TH001 1-802-210-11 THERMISTOR, NTC (SMD)
1-885-623-21 FP-1557 FLEXIBLE BOARD
*********************
A-1872-028-A FP-1582 FLEXIBLE BOARD, COMPLETE
*******************************
(All mounted parts are not supplied, but they are included in FP-1582 FLEXIBLE
COMPLETE BOARD.)
A-1871-872-A FR-319 BOARD, COMPLETE
**********************
(Q9601 is not supplied, but this is included in FR-319 COMPLETE BOARD.)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
A-1825-472-A HN-003 BOARD, COMPLETE
**********************
< CAPACITOR >
C1001 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C1002 1-127-820-11 CERAMIC CHIP 4.7uF 10% 16V
C1003 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C1004 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1005 1-100-597-91 CERAMIC CHIP 0.1uF 10% 25V
C1006 1-165-875-11 CERAMIC CHIP 10uF 10% 10V
C1007 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1008 1-127-820-11 CERAMIC CHIP 4.7uF 10% 16V
C1009 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1010 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C1011 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
C1012 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C1013 1-100-743-91 CERAMIC CHIP 2.2uF 20% 16V
C1014 1-127-820-11 CERAMIC CHIP 4.7uF 10% 16V
C1015 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1016 1-137-910-11 TANTAL. CHIP 10uF 20% 16V
2-14
< DIODE >
D1002 8-719-074-08 DIODE MA4ZD03001S0
< IC >
IC1001 6-717-064-01 UPD78F0501AMC (S)-CAB-AX-91000
* IC1002 6-712-910-01 IC NJM2878F4-46 (TE2)
IC1003 6-709-933-01 IC XC9103D093MR
IC1004 6-717-746-01 IC NJM2831F06 (TE1)
* IC1101 6-713-574-01 IC R2A15219FP
< COIL >
L1001 1-456-138-11 INDUCTOR 33uH
* L1003 1-481-425-21 INDUCTOR 10uH
< TRANSISTOR >
* Q1001 6-552-311-01 TRANSISTOR MCH5837-TL-E
Q1002 6-551-622-01 TRANSISTOR 2SC6026MFV (TL3S
* Q1101 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
* Q1102 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
* Q1103 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
* Q1104 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
A-1889-556-A LD-297 BOARD, COMPLETE
**********************
(IC5602, IC5603, IC5609, IC5610, IC5611, L5601 and L5603 are not supplied, but they
are included in LD-297 COMPLETE BOARD.)
< CAPACITOR >
C4002 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5202 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C5203 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C5204 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5205 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C5206 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5207 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5208 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5209 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5210 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5211 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5212 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5213 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C5214 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C5215 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
Page 35
LD-297 MM-102 PD-465
Ref. No. Part No. Description
C5216 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V
C5217 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C5218 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C5219 1-165-897-11 TANTAL. CHIP 22uF 20% 10V
C5604 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5605 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5606 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5609 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5610 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5612 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5616 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5617 1-165-897-11 TANTAL. CHIP 22uF 20% 10V
C5618 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5620 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5621 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5622 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5623 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5624 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5625 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5627 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5628 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C5629 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C5630 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5631 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5632 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5636 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5637 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5638 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5639 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C5640 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5641 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C5642 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5643 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C5644 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5645 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5648 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5649 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5651 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5652 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C5653 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5654 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5655 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C5656 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C7501 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7502 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7503 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7504 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8001 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8002 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
< CONNECTOR >
* CN4001 1-842-176-51 CONNECTOR, FPC (ZIF) 61P
* CN4002 1-842-176-51 CONNECTOR, FPC (ZIF) 61P
CN4003 1-821-501-11 CONNECTOR, FPC (ZIF) 51P
CN4004 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P
CN4005 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P
CN4006 1-816-654-61 FFC/FPC CONNECTOR (LIF) 6P
CN8001 1-822-837-21 ｶ-ﾄﾞ CONNECTOR
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
< DIODE >
D4001 8-719-027-76 DIODE 1SS357
D8001 6-501-216-01 DIODE CL-271HR-C-TS
< IC >
* IC5201 6-808-503-01 IC BU24130GU-E2
IC5202 6-715-211-01 IC MM3404A28URE
IC5601 6-716-760-01 IC R2J30503LG
IC5602 (Not supplied) IC LV8417CS-TE-L-H
IC5603 (Not supplied) IC LV8417CS-TE-L-H
IC5605 6-716-952-01 IC R2A30427BM
IC5606 6-716-952-01 IC R2A30427BM
IC5609 (Not supplied) IC TPS63060DSCR
IC5610 (Not supplied) IC TPS63060DSCR
IC5611 (Not supplied) IC LV8417CS-TE-L-H
< COIL >
L5601 (Not supplied) INDUCTOR 2uH
L5603 (Not supplied) INDUCTOR 2uH
< TRANSISTOR >
* Q4002 6-552-723-01 TRANSISTOR SSM6N37FE, RSONYM
< RESISTOR >
R4001 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R4006 1-218-973-11 METAL CHIP 47K 5% 1/16W
R4008 1-218-965-11 METAL CHIP 10K 5% 1/16W
R5201 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R5202 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R5203 1-208-721-11 METAL CHIP 39K 0.5% 1/16W
R5204 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R5205 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R5206 1-208-721-11 METAL CHIP 39K 0.5% 1/16W
R5207 1-218-965-11 METAL CHIP 10K 5% 1/16W
R5208 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R5209 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R5210 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R5211 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R5212 1-208-721-11 METAL CHIP 39K 0.5% 1/16W
R5213 1-208-721-11 METAL CHIP 39K 0.5% 1/16W
R5214 1-208-943-11 METAL CHIP 220K 0.5% 1/16W
R5215 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R5216 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R5217 1-208-941-11 METAL CHIP 180K 0.5% 1/16W
R5219 1-208-697-11 METAL CHIP 3.9K 0.5% 1/16W
R5614 1-218-969-11 METAL CHIP 22K 5% 1/16W
R5618 1-218-898-11 METAL CHIP 130K 0.5% 1/10W
R5619 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R5637 1-208-711-11 METAL CHIP 15K 0.5% 1/16W
R5638 1-218-982-11 METAL CHIP 270K 5% 1/16W
R5639 1-218-982-11 METAL CHIP 270K 5% 1/16W
R5648 1-218-969-11 METAL CHIP 22K 5% 1/16W
R5649 1-218-969-11 METAL CHIP 22K 5% 1/16W
R5650 1-218-965-11 METAL CHIP 10K 5% 1/16W
R5651 1-218-965-11 METAL CHIP 10K 5% 1/16W
R5655 1-218-898-11 METAL CHIP 130K 0.5% 1/10W
R5656 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R5659 1-218-977-11 METAL CHIP 100K 5% 1/16W
2-15
R8024 1-218-943-11 METAL CHIP 150 5% 1/16W
R8042 1-218-953-11 METAL CHIP 1K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB4001 1-234-381-11 RES, NETWORK 100K (1005X4)
RB5201 1-234-377-21 RES, NETWORK 4.7K (1005X4)
RB8001 1-200-051-21 RES, NETWORK 150 (1005X4)
RB8002 1-234-372-11 RES, NETWORK 100 (1005X4)
< SENSOR >
* SE7501 1-489-735-11 SENSOR, ANGULAR VELOCITY
A-1878-202-A MM-102 BOARD, COMPLETE (SERVICE) (96G)
*******************************
(IC8101 and IC8201 are not supplied, but they are included in MM-102 COMPLETE
BOARD.)
< CAPACITOR >
C8102 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C8103 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8104 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8202 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C8203 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8204 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C8701 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
< CONNECTOR >
* CN8101 1-816-647-61 FFC/FPC CONNECTOR (LIF) 18P
< FERRITE BEAD >
FB8701 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8702 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8703 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8704 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8705 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8706 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8707 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB8708 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
< IC >
IC8101 (Not supplied) IC THGBM4G8D4GBAIE
IC8201 (Not supplied) IC THGBM4G9D8GBAII
IC8701 6-716-442-11 IC MM3404A29URE
< RESISTOR >
R8101 1-218-965-11 METAL CHIP 10K 5% 1/16W
R8112 1-218-990-81 SHORT CHIP 0
R8202 1-218-990-81 SHORT CHIP 0
< COMPOSITION CIRCUIT BLOCK >
RB8101 1-234-372-11 RES, NETWORK 100 (1005X4)
RB8102 1-234-372-11 RES, NETWORK 100 (1005X4)
Ref. No. Part No. DescriptionRef. No. Part No. Description
A-1852-433-A PD-465 BOARD, COMPLETE (GPS Model)
A-1852-434-A PD-465 BOARD, COMPLETE (Non GPS Model)
**********************
< CAPACITOR >
C6001 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6002 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C6003 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C6019 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C6020 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6021 1-100-415-91 CERAMIC CHIP 0.47uF 10% 6.3V
C6022 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C6023 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C6024 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C6025 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C6026 1-112-021-91 CERAMIC CHIP 2.2uF 20% 16V
C6027 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6029 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C6030 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6031 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6032 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C6033 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C6102 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6105 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
(GPS Model)
C6106 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
(GPS Model)
C6107 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
(GPS Model)
C6108 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
(GPS Model)
C6109 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
(GPS Model)
C6110 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
(GPS Model)
< CONNECTOR >
* CN6001 1-842-522-21 CONNECTOR, FPC (ZIF) 61P
CN6002 1-821-857-51 CONNECTOR, FPC (LIF (NON-ZIF)) 6P
* CN6003 1-842-522-21 CONNECTOR, FPC (ZIF) 61P
CN6004 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
CN6005 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
CN6007 1-821-652-11 CONNECTOR, BOARD TO BOARD (REC
CN6101 1-816-655-61 CONNECTOR, FFC/FPC 8P (GPS Model)
< DIODE >
D6002 6-502-934-01 DIODE DB2S31100K8
< IC >
* IC6101 6-712-051-01 IC SN65LVDS302ZQER
IC6102 6-715-211-01 IC MM3404A28URE (GPS Model)
< COIL >
* L6001 1-481-102-21 INDUCTOR 10uH
* L6002 1-481-102-21 INDUCTOR 10uH
< TRANSISTOR >
Q6001 6-552-538-01 TRANSISTOR DMG9640N0R
Q6002 6-552-538-01 TRANSISTOR DMG9640N0R
Page 36
PD-465 PJ-104 RH-014 VC-658
Ref. No. Part No. Description
< RESISTOR >
R6041 1-218-953-11 METAL CHIP 1K 5% 1/16W
R6042 1-218-953-11 METAL CHIP 1K 5% 1/16W
R6043 1-218-953-11 METAL CHIP 1K 5% 1/16W
R6102 1-218-971-11 METAL CHIP 33K 5% 1/16W
R6106 1-218-969-11 METAL CHIP 22K 5% 1/16W
< SENSOR >
* SE6001 1-487-118-11 GMR SENSOR
A-1872-021-A PJ-104 BOARD, COMPLETE
*********************
(All mounted parts are not supplied, but they are included in PJ-104 COMPLETE
BOARD.)
A-1871-741-A RH-014 BOARD, COMPLETE
**********************
(BT7001 is not included in RH-014 COMPLETE BOARD)
< BATTERY HOLDER >
BH7001 1-251-928-21 HOLDER, BATTERY
< BATTERY >
BT7001 1-756-134-15 BATTERY, LITHIUM (SECONDARY)
< CAPACITOR >
C2601 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2602 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2603 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2604 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2605 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2606 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2607 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2608 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2609 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2610 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2611 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2612 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C2613 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C2614 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2615 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2616 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
C2617 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2618 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2801 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2802 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2803 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2804 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2805 1-127-988-81 CERAMIC CHIP 0.015uF 10% 16V
C2806 1-127-988-81 CERAMIC CHIP 0.015uF 10% 16V
C2807 1-127-988-81 CERAMIC CHIP 0.015uF 10% 16V
C2810 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2814 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C2815 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2817 1-127-988-81 CERAMIC CHIP 0.015uF 10% 16V
C2818 1-127-988-81 CERAMIC CHIP 0.015uF 10% 16V
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
C2820 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C2821 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2822 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2823 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2824 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2828 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2829 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2830 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2831 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2832 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C2833 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2834 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2835 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2836 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2837 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2841 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2849 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2850 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2852 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C2853 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2854 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2855 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C6401 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6402 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6403 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6404 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6405 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C6406 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C6411 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7001 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C7002 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7003 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C7004 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C7006 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C7007 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C7201 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C7202 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C7203 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C7204 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C7208 1-164-933-11 CERAMIC CHIP 220PF 10% 50V
< CONNECTOR >
* CN7001 1-842-522-21 CONNECTOR, FPC (ZIF) 61P
CN7002 1-815-794-13 CONNECTOR (MULTIPLE)
CN7003 1-816-649-51 FFC/CONNECTOR, FPC (LIF) 22P
CN7004 1-816-654-61 FFC/FPC CONNECTOR (LIF) 6P
CN7005 1-816-649-51 FFC/CONNECTOR, FPC (LIF) 22P
< DIODE >
D7201 8-719-027-76 DIODE 1SS357
< FERRITE BEAD >
FB7001 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7002 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7003 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7004 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7005 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7006 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7010 1-400-833-21 SMD EMI FERRITE
2-16
FB7011 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB7201 1-414-864-11 FERRITE, EMI (SMD) (1608)
< IC >
* IC2601 6-714-928-01 IC BD8871GW-E2
* IC2801 6-713-028-01 IC NN12926A-BB
IC6401 6-715-342-01 IC MM3404A25URE
IC6402 6-717-032-01 IC TC7MP3125FTG (EB)
IC6403 6-710-499-01 IC TC7MP3245FTG (EB, A)
IC7201 6-716-796-01 IC TPS61305YFFR
< JACK >
J7001 1-793-703-21 JACK (DIA. 3.5)
J7002 1-818-055-21 JACK
< COIL >
* L2601 1-481-425-21 INDUCTOR 10uH
* L2602 1-481-425-21 INDUCTOR 10uH
* L2802 1-481-425-21 INDUCTOR 10uH
* L2803 1-481-425-21 INDUCTOR 10uH
* L2804 1-481-102-21 INDUCTOR 10uH
L7201 1-481-074-21 INDUCTOR 2.2uH
< TRANSISTOR >
* Q6401 6-553-023-01 TRANSISTOR FK3303010L
< RESISTOR >
R2601 1-218-978-11 METAL CHIP 120K 5% 1/16W
R2602 1-218-978-11 METAL CHIP 120K 5% 1/16W
R2603 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2604 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2605 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W
R2606 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W
* R2801 1-250-503-11 METAL CHIP 2.2K 1% 1/16W
* R2804 1-250-503-11 METAL CHIP 2.2K 1% 1/16W
* R2805 1-250-503-11 METAL CHIP 2.2K 1% 1/16W
R2811 1-218-971-11 METAL CHIP 33K 5% 1/16W
R2813 1-218-971-11 METAL CHIP 33K 5% 1/16W
R2814 1-218-941-81 METAL CHIP 100 5% 1/16W
R2815 1-218-941-81 METAL CHIP 100 5% 1/16W
R2816 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2827 1-218-969-11 METAL CHIP 22K 5% 1/16W
R2828 1-218-969-11 METAL CHIP 22K 5% 1/16W
R2829 1-250-468-11 METAL CHIP 75 1% 1/16W
R6414 1-218-990-81 SHORT CHIP 0
R7004 1-218-977-11 METAL CHIP 100K 5% 1/16W
R7008 1-218-990-81 SHORT CHIP 0
R7009 1-218-990-81 SHORT CHIP 0
R7010 1-218-990-81 SHORT CHIP 0
R7201 1-218-965-11 METAL CHIP 10K 5% 1/16W
R7203 1-218-965-11 METAL CHIP 10K 5% 1/16W
R7212 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
* R7213 1-250-479-11 METAL CHIP 220 1% 1/16W
* R7214 1-250-479-11 METAL CHIP 220 1% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB2602 1-234-370-21 RES, NETWORK 22 (1005X4)
Ref. No. Part No. DescriptionRef. No. Part No. Description
RB6401 1-234-378-21 RES, NETWORK 10K (1005X4)
RB6402 1-234-378-21 RES, NETWORK 10K (1005X4)
RB6403 1-234-378-21 RES, NETWORK 10K (1005X4)
< SWITCH >
S7001 1-798-119-11 SWITCH, TACTILE
< SENSOR >
* SE6401 1-487-118-21 GMR SENSOR
< VARISTOR >
VDR703 1-802-090-21 VARISTOR, CHIP
VDR704 1-802-090-21 VARISTOR, CHIP
VDR705 1-802-090-21 VARISTOR, CHIP
VDR709 1-802-090-21 VARISTOR, CHIP
VDR710 1-802-090-21 VARISTOR, CHIP
A-1885-417-A VC-658 BOARD, COMPLETE (SERVICE)
*******************************
(IC1301 is not supplied, but this is included in VC-658 COMPLETE BOARD (SERVICE).)
< CAPACITOR >
C1001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1002 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1003 1-164-860-11 CERAMIC CHIP 27PF 5% 50V
C1301 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
C1302 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
* C1303 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
C1304 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1305 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1306 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C1307 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1308 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1309 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1310 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1313 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C1314 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C1315 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1316 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1317 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1318 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1319 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
C1320 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1321 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1322 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1323 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1324 1-164-933-11 CERAMIC CHIP 220PF 10% 50V
C1325 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1327 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
C1331 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1332 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C1410 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1411 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1412 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1413 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1421 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1423 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
Page 37
VC-658
Ref. No. Part No. Description
C1424 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1428 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1438 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1442 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
C1443 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
C1444 1-164-856-81 CERAMIC CHIP 18PF 5% 50V
C1501 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C1504 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1505 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1506 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C1507 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1508 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
* C1509 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
C1510 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1511 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
C1512 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1513 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1514 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1515 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1516 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1518 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1519 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1520 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1523 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1524 1-116-724-11 CERAMIC CHIP 4.7uF 20% 6.3V
C1526 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1527 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1529 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C1530 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2701 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C2702 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2703 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2704 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2705 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C2706 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2707 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2708 1-164-878-11 CERAMIC CHIP 150PF 5% 50V
C2709 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2710 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2711 1-164-934-11 CERAMIC CHIP 330PF 10% 50V
C3302 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4301 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4302 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4303 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4304 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4305 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4306 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C4308 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
* C4309 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
C4310 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
* C4311 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
* C4312 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
* C4313 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
* C4314 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
* C4315 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
C4316 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C4317 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4318 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C4319 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
C4320 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C4321 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4322 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4323 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
C4324 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
C4325 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C4326 1-100-597-91 CERAMIC CHIP 0.1uF 10% 25V
C4327 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C4328 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C4329 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C4330 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C4331 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4332 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C4333 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C4334 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C4337 1-116-729-11 CERAMIC CHIP 2.2uF 20% 10V
C4338 1-100-591-91 CERAMIC CHIP 1uF 10% 25V
C4349 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4350 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C4355 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
C4801 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
* C4802 1-128-965-11 CERAMIC CHIP 13PF 5% 50V
* C4803 1-128-965-11 CERAMIC CHIP 13PF 5% 50V
C4804 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C4805 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4806 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4807 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4808 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4809 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C4810 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C4811 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C9101 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9102 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C9103 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9105 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
C9107 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9109 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9111 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9112 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C9113 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9115 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C9116 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C9118 1-114-419-21 CERAMIC CHIP 10uF 10% 16V
C9119 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR >
* CN1001 1-842-176-51 CONNECTOR, FPC (ZIF) 61P
* CN1002 1-842-176-51 CONNECTOR, FPC (ZIF) 61P
* CN1003 1-842-176-51 CONNECTOR, FPC (ZIF) 61P
CN1004 1-821-501-11 CONNECTOR, FPC (ZIF) 51P
* CN1005 1-822-893-11 CONNECTOR, FPC (ZIF) 33P
* CN1006 1-822-893-11 CONNECTOR, FPC (ZIF) 33P
CN1007 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P
* CN1008 1-816-647-61 FFC/FPC CONNECTOR (LIF) 18P
CN1009 1-842-602-11 CONNECTOR, HDMI
CN1010 1-816-654-61 FFC/FPC CONNECTOR (LIF) 6P
CN1011 1-580-789-21 PIN, CONNECTOR (SMD) 6P
CN9101 1-843-120-11 HEADER ASSEMBRY
2-17
CN9102 1-822-425-21 CONNECTOR, USB (MINI AB)
< DIODE >
D1001 6-503-219-01 DIODE RKZ12B2KJR1
D1303 6-500-854-01 DIODE 1SS413 (TPL3)
D1304 6-500-854-01 DIODE 1SS413 (TPL3)
D1401 6-501-272-01 DIODE RB520CS-30FJT2R
D1402 6-501-272-01 DIODE RB520CS-30FJT2R
D4301 6-503-126-01 DIODE DA2S10100K8
D4302 6-503-372-01 DIODE DA3S103E0L
* D9101 6-502-988-01 DIODE RB480Y-40T2R
D9102 6-503-702-01 DIODE RB070M-30FJTR
D9103 6-502-934-01 DIODE DB2S31100K8
D9105 6-503-217-01 DIODE RKZ5.6B2KJR1
< FUSE >
* F001 1-576-286-31 FUSE (1.4A/24V)
* F002 1-576-286-31 FUSE (1.4A/24V)
* F003 1-576-286-31 FUSE (1.4A/24V)
* F004 1-576-286-31 FUSE (1.4A/24V)
* F005 1-576-286-31 FUSE (1.4A/24V)
* F006 1-576-286-31 FUSE (1.4A/24V)
* F007 1-523-180-31 FUSE (2.5A/24V)
* F008 1-576-872-31 FUSE (0.25A/50V)
F009 1-523-134-31 FUSE (2A/50V)
< FERRITE BEAD >
FB1301 1-400-725-21 FERRITE, EMI (SMD) (1005)
FB1302 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB1303 1-400-354-11 INDUCTOR, FERRITE BEAD (1005)
FB1304 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB1401 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB1402 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB1403 1-400-921-21 FERRITE, EMI (SMD)
FB1404 1-400-833-21 SMD EMI FERRITE
FB1405 1-400-833-21 SMD EMI FERRITE
FB1406 1-400-833-21 SMD EMI FERRITE
FB1501 1-481-912-21 EMI FERRITE (SMD) (1005)
FB2701 1-414-864-11 FERRITE, EMI (SMD) (1608)
< IC >
IC1301 (Not supplied) IC AVY2G2G05A
IC1302 6-716-878-01 IC AK8153AU-L
IC2701 6-712-944-01 IC CS42L52-CNZR
* IC3301 6-712-050-01 IC SN65LVDS301ZQER
IC4301 6-717-389-01 IC BD8330AGU-E2
IC4302 6-716-945-01 IC BD8331GU-E2
IC4303 6-718-155-01 IC R1207N823B-TR-FE
* IC4304 6-714-502-01 IC BD2224G-TR
IC4801 6-718-258-01 IC MB95005ABGL-G-135-ERE1
IC9101 6-718-158-01 IC MAX14593EEWV+TG1A
IC9102 6-718-154-01 IC BD8668GW-E2
IC9103 6-716-783-01 IC BD11600NUX-E2
IC9104 6-716-783-01 IC BD11600NUX-E2
* IC9105 6-714-833-01 IC TPS2553DBVR-1
< COIL >
* L1301 1-481-425-21 INDUCTOR 10uH
Ref. No. Part No. DescriptionRef. No. Part No. Description
* L2701 1-481-425-21 INDUCTOR 10uH
* L2702 1-481-425-21 INDUCTOR 10uH
* L2703 1-481-425-21 INDUCTOR 10uH
* L2704 1-481-425-21 INDUCTOR 10uH
* L2705 1-481-425-21 INDUCTOR 10uH
L4301 1-460-355-11 INDUCTOR 4.7uH
L4302 1-460-370-11 INDUCTOR 10uH
L4303 1-460-370-11 INDUCTOR 10uH
L4304 1-460-370-11 INDUCTOR 10uH
L4305 1-460-370-11 INDUCTOR 10uH
* L4306 1-457-858-11 INDUCTOR 4.7uH
L4307 1-460-369-11 INDUCTOR 33uH
* L4308 1-481-425-21 INDUCTOR 10uH
* L9101 1-457-858-11 INDUCTOR 4.7uH
< LINE FILTER >
LF1301 1-457-374-21 COMMOM MODE CHOKE COIL
LF1302 1-457-374-21 COMMOM MODE CHOKE COIL
LF1303 1-457-374-21 COMMOM MODE CHOKE COIL
LF1304 1-457-374-21 COMMOM MODE CHOKE COIL
LF9102 1-457-223-11 COMMON MODE CHOKE COIL
LF9103 1-457-223-11 COMMON MODE CHOKE COIL
< TRANSISTOR >
* Q1301 6-553-023-01 TRANSISTOR FK3303010L
* Q1302 6-552-723-01 TRANSISTOR SSM6N37FE, RSONYM
* Q1402 6-552-344-01 TRANSISTOR DRA3143T0L
* Q1403 6-552-535-01 TRANSISTOR DMG964030R
* Q3301 6-552-354-01 TRANSISTOR DRC3144E0L
Q4301 6-553-038-01 TRANSISTOR DRA3115T0L
Q4302 6-553-038-01 TRANSISTOR DRA3115T0L
Q4303 8-729-043-60 TRANSISTOR CPH6102-TL-E
* Q4304 6-552-354-01 TRANSISTOR DRC3144E0L
Q4305 6-551-663-01 TRANSISTOR MTM684110LS0
* Q4306 6-552-354-01 TRANSISTOR DRC3144E0L
Q4307 6-552-874-01 TRANSISTOR RW1C025ZPT2CR
* Q4801 6-552-535-01 TRANSISTOR DMG964030R
Q9102 6-553-025-01 TRANSISTOR MCH6341-TL-E
* Q9103 6-552-348-01 TRANSISTOR DRC3114E0L
* Q9107 6-552-348-01 TRANSISTOR DRC3114E0L
< RESISTOR >
R1002 1-218-965-11 METAL CHIP 10K 5% 1/16W
R1003 1-218-945-11 METAL CHIP 220 5% 1/16W
R1004 1-218-953-11 METAL CHIP 1K 5% 1/16W
R1313 1-220-169-11 METAL CHIP 75 5% 1/16W
R1315 1-208-869-11 METAL CHIP 180 0.5% 1/16W
R1321 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W
R1331 1-250-481-11 METAL CHIP 270 1% 1/16W
R1332 1-218-970-11 METAL CHIP 27K 5% 1/16W
R1334 1-218-941-81 METAL CHIP 100 5% 1/16W
R1335 1-218-953-11 METAL CHIP 1K 5% 1/16W
R1342 1-218-956-11 METAL CHIP 1.8K 5% 1/16W
R1343 1-218-956-11 METAL CHIP 1.8K 5% 1/16W
R1348 1-220-169-11 METAL CHIP 75 5% 1/16W
R1350 1-250-467-11 METAL CHIP 68 1% 1/16W
R1351 1-250-467-11 METAL CHIP 68 1% 1/16W
R1409 1-218-941-81 METAL CHIP 100 5% 1/16W
Page 38
VC-658 XL-013
Ref. No. Part No. Description
R1410 1-218-941-81 METAL CHIP 100 5% 1/16W
R1411 1-218-943-11 METAL CHIP 150 5% 1/16W
R1412 1-218-943-11 METAL CHIP 150 5% 1/16W
R1413 1-218-941-81 METAL CHIP 100 5% 1/16W
R1414 1-218-941-81 METAL CHIP 100 5% 1/16W
R1421 1-218-945-11 METAL CHIP 220 5% 1/16W
R1454 1-218-973-11 METAL CHIP 47K 5% 1/16W
R1455 1-218-989-11 METAL CHIP 1M 5% 1/16W
R1460 1-218-977-11 METAL CHIP 100K 5% 1/16W
R1471 1-218-990-81 SHORT CHIP 0
R1472 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R1473 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R1515 1-208-668-11 METAL CHIP 240 0.5% 1/16W
R2702 1-218-971-11 METAL CHIP 33K 5% 1/16W
R3004 1-218-990-81 SHORT CHIP 0
R3005 1-218-990-81 SHORT CHIP 0
R3006 1-218-945-11 METAL CHIP 220 5% 1/16W
R3007 1-218-941-81 METAL CHIP 100 5% 1/16W
R3316 1-218-941-81 METAL CHIP 100 5% 1/16W
R3317 1-218-977-11 METAL CHIP 100K 5% 1/16W
R4302 1-218-941-81 METAL CHIP 100 5% 1/16W
R4303 1-250-535-11 METAL CHIP 47K 1% 1/16W
R4315 1-220-876-81 METAL CHIP 18 0.5% 1/16W
R4334 1-218-965-11 METAL CHIP 10K 5% 1/16W
R4343 1-216-796-11 METAL CHIP 8.2 5% 1/10W
R4344 1-218-953-11 METAL CHIP 1K 5% 1/16W
R4345 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R4346 1-218-965-11 METAL CHIP 10K 5% 1/16W
R4347 1-218-989-11 METAL CHIP 1M 5% 1/16W
R4348 1-218-953-11 METAL CHIP 1K 5% 1/16W
R4349 1-220-876-81 METAL CHIP 18 0.5% 1/16W
R4802 1-245-604-11 METAL CHIP 10M 5% 1/16W
R4803 1-208-893-11 METAL CHIP 1.8K 0.5% 1/16W
R4807 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W
R4808 1-218-973-11 METAL CHIP 47K 5% 1/16W
R4809 1-218-953-11 METAL CHIP 1K 5% 1/16W
R4810 1-218-949-11 METAL CHIP 470 5% 1/16W
R4812 1-218-973-11 METAL CHIP 47K 5% 1/16W
R4814 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R4815 1-208-935-11 METAL CHIP 100K 0.5% 1/16W
R4817 1-250-535-11 METAL CHIP 47K 1% 1/16W
* R4818 1-250-543-11 METAL CHIP 100K 1% 1/16W
R9116 1-218-941-81 METAL CHIP 100 5% 1/16W
R9120 1-218-989-11 METAL CHIP 1M 5% 1/16W
R9133 1-248-311-11 RES-CHIP 0.1 1% 1/4W
R9134 1-250-535-11 METAL CHIP 47K 1% 1/16W
R9135 1-218-969-11 METAL CHIP 22K 5% 1/16W
R9136 1-218-944-11 METAL CHIP 180 5% 1/16W
R9137 1-208-709-11 METAL CHIP 12K 0.5% 1/16W
R9138 1-218-973-11 METAL CHIP 47K 5% 1/16W
R9140 1-257-317-11 METAL CHIP 47 1% 1/2W
R9141 1-218-963-11 METAL CHIP 6.8K 5% 1/16W
R9142 1-218-953-11 METAL CHIP 1K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB1001 1-234-373-21 RES, NETWORK 220 (1005X4)
RB1002 1-234-373-21 RES, NETWORK 220 (1005X4)
RB1302 1-234-377-21 RES, NETWORK 4.7K (1005X4)
RB1402 1-234-372-11 RES, NETWORK 100 (1005X4)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Ref. No. Part No. Description
RB1403 1-200-051-21 RES, NETWORK 150 (1005X4)
RB1404 1-234-372-11 RES, NETWORK 100 (1005X4)
RB1405 1-234-372-11 RES, NETWORK 100 (1005X4)
RB4801 1-234-375-21 RES, NETWORK 1K (1005X4)
RB4802 1-234-378-21 RES, NETWORK 10K (1005X4)
RB4803 1-234-378-21 RES, NETWORK 10K (1005X4)
RB9101 1-234-381-11 RES, NETWORK 100K (1005X4)
< VARISTOR >
VD1001 1-802-090-21 VARISTOR, CHIP
VD1003 1-802-090-21 VARISTOR, CHIP
VD1004 1-805-774-21 VARISTOR, CHIP
VD1005 1-805-774-21 VARISTOR, CHIP
< VIBRATOR >
X1302 1-814-219-31 QUARTZ CRYSTAL OSCILLATOR (60MHz)
X4801 1-781-525-11 VIBRATOR, CRYSTAL (32.768kHz)
A-1825-473-A XL-013 BOARD, COMPLETE
*********************
(IC2301 is not supplied, but this is included in XL-013 COMPLETE BOARD.)
< CAPACITOR >
C2217 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2218 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2219 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2220 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2221 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2222 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2223 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2224 1-128-594-11 ELECT CHIP 1uF 20% 50V
C2225 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2226 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2227 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2228 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C2229 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C2230 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C2231 1-112-300-91 CERAMIC CHIP 4.7uF 10% 10V
C2303 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2304 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V
C2305 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2306 1-137-910-11 TANTAL. CHIP 10uF 20% 16V
C2307 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
C2308 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
C2309 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
C2310 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C2311 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
C2312 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
C2313 1-113-984-11 TANTAL. CHIP 1.5uF 20% 35V
< CONNECTOR >
CN2201 1-816-650-51 FFC/FPC CONNECTOR (LIF) 24P
CN2202 1-820-791-11 XLR CONNECTOR (RECEPTACLE) 3P
< DIODE >
D2201 8-719-056-23 DIODE MA2S111-(K8).SO
2-18
D2202 8-719-056-23 DIODE MA2S111-(K8).SO
D2203 8-719-056-23 DIODE MA2S111-(K8).SO
D2204 8-719-056-23 DIODE MA2S111-(K8).SO
D2205 8-719-056-23 DIODE MA2S111-(K8).SO
D2206 8-719-056-23 DIODE MA2S111-(K8).SO
D2207 8-719-056-23 DIODE MA2S111-(K8).SO
D2208 8-719-056-23 DIODE MA2S111-(K8).SO
D2209 8-719-056-23 DIODE MA2S111-(K8).SO
D2210 8-719-056-23 DIODE MA2S111-(K8).SO
D2211 8-719-056-23 DIODE MA2S111-(K8).SO
D2212 8-719-056-23 DIODE MA2S111-(K8).SO
D2213 8-719-056-23 DIODE MA2S111-(K8).SO
D2214 8-719-056-23 DIODE MA2S111-(K8).SO
D2215 8-719-056-23 DIODE MA2S111-(K8).SO
D2216 8-719-056-23 DIODE MA2S111-(K8).SO
< IC >
* IC2201 6-710-823-01 IC NJM2737RB1 (TE2)
* IC2202 6-710-823-01 IC NJM2737RB1 (TE2)
IC2203 6-706-906-01 IC NJM2732RB1 (TE2)
IC2301 (Not supplied) IC TK11840LTL-G
< COIL >
* L2201 1-481-425-21 INDUCTOR 10uH
* L2202 1-481-425-21 INDUCTOR 10uH
* L2203 1-481-425-21 INDUCTOR 10uH
* L2204 1-481-425-21 INDUCTOR 10uH
L2301 1-456-499-11 INDUCTOR 4.7uH
L2302 1-456-138-11 INDUCTOR 33uH
< TRANSISTOR >
Q2201 6-551-294-01 TRANSISTOR MCH6606-TL-E
Q2202 6-551-294-01 TRANSISTOR MCH6606-TL-E
Q2203 6-551-294-01 TRANSISTOR MCH6606-TL-E
Q2204 6-551-294-01 TRANSISTOR MCH6606-TL-E
Q2205 6-550-356-01 TRANSISTOR MCH6616-TL-E
Q2206 6-550-356-01 TRANSISTOR MCH6616-TL-E
* Q2207 6-552-354-01 TRANSISTOR DRC3144E0L
* Q2208 6-552-354-01 TRANSISTOR DRC3144E0L
Q2302 6-552-748-01 TRANSISTOR CPH5870-TL-E
Q2303 6-551-622-01 TRANSISTOR 2SC6026MFV (TL3S
* Q2304 6-552-354-01 TRANSISTOR DRC3144E0L
Q2305 8-729-119-64 TRANSISTOR 2SA811A-C17
* Q2306 6-552-354-01 TRANSISTOR DRC3144E0L
Q2307 8-729-119-64 TRANSISTOR 2SA811A-C17
* Q2331 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
* Q2332 6-551-625-01 TRANSISTOR RN2104MFV (TL3S
* Q2335 6-552-354-01 TRANSISTOR DRC3144E0L
* Q2336 6-552-354-01 TRANSISTOR DRC3144E0L
< RESISTOR >
R2201 1-220-300-91 METAL CHIP 6.8K 5% 1/2W
R2202 1-220-300-91 METAL CHIP 6.8K 5% 1/2W
R2209 1-216-853-11 METAL CHIP 470K 5% 1/10W
R2212 1-216-853-11 METAL CHIP 470K 5% 1/10W
R2213 1-220-300-91 METAL CHIP 6.8K 5% 1/2W
R2216 1-220-300-91 METAL CHIP 6.8K 5% 1/2W
R2225 1-218-977-11 METAL CHIP 100K 5% 1/16W
Ref. No. Part No. DescriptionRef. No. Part No. Description
R2226 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2227 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2228 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2229 1-218-949-11 METAL CHIP 470 5% 1/16W
R2230 1-218-949-11 METAL CHIP 470 5% 1/16W
R2231 1-218-949-11 METAL CHIP 470 5% 1/16W
R2232 1-218-949-11 METAL CHIP 470 5% 1/16W
R2233 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2234 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2235 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2236 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2237 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2238 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2239 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2240 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2241 1-218-981-91 METAL CHIP 220K 5% 1/16W
R2242 1-218-981-91 METAL CHIP 220K 5% 1/16W
R2243 1-218-981-91 METAL CHIP 220K 5% 1/16W
R2244 1-218-981-91 METAL CHIP 220K 5% 1/16W
R2245 1-218-901-11 METAL CHIP 180K 0.5% 1/10W
R2246 1-218-901-11 METAL CHIP 180K 0.5% 1/10W
R2247 1-218-901-11 METAL CHIP 180K 0.5% 1/10W
R2248 1-218-901-11 METAL CHIP 180K 0.5% 1/10W
R2249 1-218-949-11 METAL CHIP 470 5% 1/16W
R2250 1-218-949-11 METAL CHIP 470 5% 1/16W
R2251 1-218-949-11 METAL CHIP 470 5% 1/16W
R2252 1-218-949-11 METAL CHIP 470 5% 1/16W
R2253 1-208-918-11 METAL CHIP 20K 0.5% 1/16W
R2254 1-208-918-11 METAL CHIP 20K 0.5% 1/16W
R2255 1-208-918-11 METAL CHIP 20K 0.5% 1/16W
R2256 1-208-918-11 METAL CHIP 20K 0.5% 1/16W
R2257 1-208-711-11 METAL CHIP 15K 0.5% 1/16W
R2258 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R2259 1-208-711-11 METAL CHIP 15K 0.5% 1/16W
R2260 1-208-909-11 METAL CHIP 8.2K 0.5% 1/16W
R2261 1-208-697-11 METAL CHIP 3.9K 0.5% 1/16W
R2262 1-208-697-11 METAL CHIP 3.9K 0.5% 1/16W
R2263 1-208-697-11 METAL CHIP 3.9K 0.5% 1/16W
R2264 1-208-697-11 METAL CHIP 3.9K 0.5% 1/16W
R2265 1-208-671-11 METAL CHIP 330 0.5% 1/16W
R2266 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2267 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2268 1-208-671-11 METAL CHIP 330 0.5% 1/16W
R2269 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2270 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2271 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R2272 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R2273 1-208-671-11 METAL CHIP 330 0.5% 1/16W
R2274 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R2275 1-208-671-11 METAL CHIP 330 0.5% 1/16W
R2276 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R2277 1-208-905-11 METAL CHIP 5.6K 0.5% 1/16W
R2278 1-208-905-11 METAL CHIP 5.6K 0.5% 1/16W
R2279 1-218-929-11 METAL CHIP 10 5% 1/16W
R2280 1-218-929-11 METAL CHIP 10 5% 1/16W
R2281 1-218-929-11 METAL CHIP 10 5% 1/16W
R2282 1-218-929-11 METAL CHIP 10 5% 1/16W
R2283 1-218-929-11 METAL CHIP 10 5% 1/16W
Page 39
Ref. No. Part No. Description
R2284 1-218-929-11 METAL CHIP 10 5% 1/16W
R2285 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2286 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2287 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2288 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2289 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2290 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2291 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2292 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2302 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2303 1-218-951-11 METAL CHIP 680 5% 1/16W
R2304 1-208-893-11 METAL CHIP 1.8K 0.5% 1/16W
R2305 1-218-965-11 METAL CHIP 10K 5% 1/16W
R2306 1-208-955-11 METAL CHIP 680K 0.5% 1/16W
R2307 1-208-944-81 METAL CHIP 240K 0.5% 1/16W
R2308 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2309 1-218-970-11 METAL CHIP 27K 5% 1/16W
R2310 1-218-977-11 METAL CHIP 100K 5% 1/16W
R2312 1-218-973-11 METAL CHIP 47K 5% 1/16W
R2313 1-216-849-11 METAL CHIP 220K 5% 1/10W
XL-013
R2316 1-218-973-11 METAL CHIP 47K 5% 1/16W
R2317 1-216-849-11 METAL CHIP 220K 5% 1/10W
R2331 1-218-985-11 METAL CHIP 470K 5% 1/16W
R2332 1-218-985-11 METAL CHIP 470K 5% 1/16W
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-19E
2-19E
Page 40
Ver. 1.1 2012.06
The changed portions from
Ver. 1.0 are shown in blue.
3. ASSEMBLY
CAUTION FOR HANDLING THE
LENS DEVICE (LSV-1550A-BI)
Do not hold the following part.
Lens
Very weak
Must not put the lens device (LSV-1550A-BI)
turning lens downward.
Assembly-1: Installation Cautions of the USB Arm Retainer.
Route the microphone harness.
Microphone
Flexible Board
Assembly-2: Installation Cautions of the VF Flexible Guard.
Claw
USB Arm Retainer
Claws
Assembly-4: The Method of removing of Lens Ornament.
Push
Lock
Downward
NG
OK
VF Flexible Guard
Assembly-3: Installation Cautions of the CM Flexible Guard.
Flexible Board
CM Flexible Guard
1
2
Lens Ornament
Cabinet (F) Block
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Claw
3-1
Page 41
Assembly-5: The Method of attachment of FP-1519 Flexible
Board.
Assembly-6: Installation Cautions of LCD Cushion.
1 Fold dotted line parts of the FP-1519 flexible
board as shown in figure.
Adhesive tape
Valley fold
FP-1519 Flexible Board
Adhesive tape
with a detachment paper
Adhesive tape
2 Roll the FP-1519 flexible board 2 times in
the T Style Hinge M (A) Assy as shown in figure.
FP-1519
Flexible Board
Hinge Cover (U)
2 Times
T Style Hinge M (A) Assy
4 Roll the P-1519 flexible board 1 times in
the Hinge Cover (U) as shown in figure.
Apply LCD cushion.
And have
the Tab of the Release Paper and peel it off.
Release Paper
LCD cushion
Hole
LCD
Long hole
Align corner of
LCD cushion
with corner of LCD.
Align shape of
LCD unit.
Adhesive tape
Valley fold
Adhesive tape
3 Roll the FP-1519 flexible board 2 times in
the
T Style Hinge M (A) Assy as shown in figure.
HINGE COVER (O (390))
FP-1519
Flexible Board
5 Attach the P-1554 flexible board as shown in figure.
FP-1554 Flexible Board
FP-1519 Flexible Board
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
FP-1554 Flexible Board
3-2E
Page 42
4. BLOCK DIAGRAMS
4-1. OVERALL BLOCK DIAGRAM (1/5)( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS BLOCK (1/2)
IRIS
(SHUTTER)
CM-121 BOARD
IC6701
CMOS
IMAGER
DOAP - DOJP,
DOAM - DOJM
DCKP,DCKM
J1
H1
SDI,SDO,XCE,SCK
J2
D2
CN1009
CN6701
XVS
XHS
INCK
XCLR
IC4302
DC/DC CONVERTER,
LANC DRIVER
(8/10)
IC4301
DC/DC CONVERTER
(8/10)
46,43,40,
45,42,39,
37,34,28,
36,33,27,
25,22,19,
24,21,18,
16,45,42,
15,46,43,
39,36,33,
40,37,34,
27,24,21,
28,25,22,
18,15
19,16
31,30
31,30
12
12
11
11
10,8,
10,8,
9,6
9,6
2
2
4
4
LANC_SIG
FR_XRESET
E5
LANC_IN/OUT
FR_EVER_SO/SCK
FR_EVER_SI/SO/SCK
VC-658 BOARD (1/3)
CN1004
SUBL_DINN1-DINN10/DINP1-DINP10
SUBL_CLKINN/CLKINP
SENSSI/SENSSO/SENSXCS/SENSSCK
CLK_CMOS_IN_IMG
IC1302
CLOCK
GENERATOR
(2/10)
HI CONTROL,
LANC INTERFACE
SENS_VD
SENS_HD
XFLASH_RST
CLK_CMOS_IN_GEN
4
1
3
B8
A8
IC4801
(1/2)
(9/10)
L2
L3
CLK_SYS_IN
CLK_CMOS_IN
X1302
60MHz
XFLASH_RST
XSYS_RST
XCS_FRONT
XRESET_REQ
XPWR_OFF
FR_SI/SO/SCK
XEVF_SW
X4801
32.768kHz
AC30
AC29
AK28
AF2
AD30
IC1301
(1/3)
CPU,
AV SIGNAL PROCESS,
CAMERA DSP,
LENS CONTROL,
MODE CONTROL,
HDMI PROCESS
(2/10 - 4/10)
LCD_XVD
W2
LCD_XHD
W1
LCD_CLK
LCD_DATEN
XPANEL_EVF_PS_
IC_1301
PANEL_NOR/REV
XPJ_RESET
XCS_LCD
XBB_RST
AV_ SO/ SCK
I2C_SDA/SCK
TP_X/Y/SEL1
XPJ_PARK
PJ_TEMP_AD
SDO
LCD_R_0 - LCD_R_7
LCD_G_0 - LCD_G_7
LCD_B_0 - LCD_B_7
Q3301
XPANEL_EVF_PS
BEEP_PWM_P_A
XSYS_RST
SDO
BCK_CN, MCK_CN, LRCK_OUT
I2C_SDA/SCK
XSYS_RST
IC3301
LCD SERIAL
INTERFACE
TRANSMITTER
(7/10)
OVERALL (5/5)
(PAGE 4-5)
CN1006 (1/2)
5,3,
I2C_SDA
I2C_SCK
BL_H/L
15,13,
19,17,
9,7
30
32
31
23,22
23
28
24,26
3
21,20,
15
18,19
22
27
30,31
1
OVERALL (2/5)
(PAGE 4-2)
2
OVERALL (2/5)
(PAGE 4-2)
IC4303
BL DRIVE
(8/10)
BL_H/L
32
IC2701
D/A
CONVERTER,
SPEAKER AMP
(5/10)
D0 ± - D2 ±, CLK ±
PANEL_NOR/REV
XPJ_RESET
SP_R ±
CN1005 (1/2)
XCS_LCD
XBB_RST
AV_SO/SCK
TP_X/Y/SEL1
XPJ_PARK
PJ_TEMP_AD
SP_L ±
SP_R ±
SP_L ±
5
BUILT-IN
USB CABLE
CHARGE
: VIDEO SIGNAL
: AUDIO SIGNAL
: VIDEO/AUDIO SIGNAL
HDMI
(USB)
14
19
08
8,9,5,6,2,311,12
SDA, SCL
16,15
CEC
HPD
CN9101
USB_D±_STD_CN
3, 2
CN9102
3, 2
USB_ID2
4
USB_VCC
1
Q1403
LEVEL SHIFT
USB_D±
HDMI_TX0SOP-TX2SOP, HDMI_TX0SON-TX2SON
HDMI_TXCN/TXCP
Q1302
IC9101
USB POWER
MANAGEMENT
(10/10)
IC9103
USB SWITCH
(10/10)
IC9104
USB SWITCH
(10/10)
LEVEL SHIFT
USB_SEL
USB_SEL
USB_DP/DM
USB_ID
USB_VBUS
Q1301
LEVEL SHIFT
SDA, SCL
HDMI_JACK_IN
USB_SEL
USB_ID2
CEC
XCS_EVF
XCS_IC_2801
DAC_IOUT_Y
DAC_IOUT_PB
SDI0_SPDIF_IN_IC_1301
SDI1_IC_1301
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
XSTRB_FULL
STROBE_ON
JACK_AD
LANC_SIG
6
OVERALL (4/5)
(PAGE 4-4)
OVERALL (4/5)
(PAGE 4-4)
MCK_CN, LRCK_OUT, BCK_CN
SDI0_SPDIF_IN_IC_1301
4
LCD_B_0 - LCD_B_7
LCD_XVD
LCD_XHD
EVF_CLK_OUT
XCS_EVF
XBB_RST
AV_SO/SCK
XPANEL_EVF_PS
I2C_SDA/SCK
XSYS_RST
FR_XRESET
XCS_IC_2801
DAC_IOUT_Y
DAC_IOUT_PB
SDO
SDI1_IC_1301
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
SHOE_MIC_FL
SHOE_MIC_FR
XSTRB_FULL
STROBE_ON
LANC_SIG
JACK_AD
XEVF_SW
CN1003
18-25
28
29
31
14
33
15,16
27
12,13
53
57
52
60
59
46
49-51
48
47
36
37
38
40
41
10
11
56
55
34
3
OVERALL (3/5)
(PAGE 4-3)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-1
Page 43
4-2. OVERALL BLOCK DIAGRAM (2/5)( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LCD901
(LCD MODULE)
3.0 INCH
WIDE COLOR
LCD
TOUCH
PANEL
1
OVERALL (1/5)
(PAGE 4-1)
FP-1519 FLEXIBLE BOARD (1/2)
D0± - D2±, CLK±
PANEL_NOR/REV
I2C_SDA
XPJ_RESET
SP_R±
PD-465 BOARD (1/2)
CN6001 (1/2)
58, 60,
48, 50,
D0± - D2±, CLK±
44, 46,
54, 56
XBB_RST
4
XCS_LCD
9
AV_SO/SCK
8, 6
BL_H/L
14,13
PANEL_NOR/REV
33
TP_X/Y/SEL1
11,12,
17
SE6001
PANEL
NORMAL/REVERSE
DETECT
(1/2)
Q6001, Q6002
TP_SEL1
TOUCH PANEL
INTERFACE
LCD_DB0-DB7
LCD_DG0-DG7
LCD_DR0-DR7
LCD_VD
LCD_HD
LCD_CK
XBB_RST
XCS_LCD
AV_SO/SCK
BL_H/L
TP_X/Y
TP_BOT
CN6003
CN6002
TP_R
34-41
42-49
50-57
33
3,4
61,60
4, 1
31
32
5
2
2
5
2
OVERALL (1/5)
(PAGE 4-1)
08
BL_H/L
AV_SO/SCK
XCS_LCD
XBB_RST
TP_X/Y/SEL1
I2C_SCK
XPJ_PARK
PJ_TEMP_AD
SP_L±
: VIDEO SIGNAL
: AUDIO SIGNAL
31
32, 29
10
2, 1
40, 41
5
XPJ_RESET
I2C_SDA/SCK
XPJ_PARK
PJ_TEMP_AD
SP_L±
SP_R±
SP_L±
SP_R±
CN6004
CN6005
IC6101
LCD SERIAL
INTERFACE
RECEIVER
(2/2)
1, 2
1, 2
H8
H9
LCD_CK, LCD_DATEN
(SPEAKER) (L)
(SPEAKER) (R)
SP901
SP902
LCD_DB0-DB7
LCD_DG0-DG7
LCD_DR0-DR7
XPJ_RESET
I2C_SDA/SCK
XPJ_PARK
PJ_TEMP_AD
CN6007
LCD_VD
LCD_HD
PJ-104 BOARD FP-1582 FLEXIBLE
IC8601
LED
DECODER
(2/4)
CN8501
25, 3,
7, 11,
13, 15,
13, 15,
23, 19,
23, 19,
8, 4,
14, 12
14, 12
32
29, 36
29, 36
20, 24
20, 24
18, 28
18, 28
IC8602
INVERTER
LEDDRV_ON
SDA_2601,SCL_2601
IC8603
FLASH
MEMORY
(2/4)
25, 3,
7, 11,
8, 4,
32
(2/4)
23,25,
29,31,
35,37,
41,43
55,53,
49,47,
42,44,
48,50,
56,54,
38,36,
32,30,
26,24
13
15
9,19
12
3,5
16
7
23,25,
29,31,
35,37,
41,43
55,53,
49,47,
42,44,
48,50,
56,54,
38,36,
32,30,
26,24
13
15
9,19
12
3,5
16
7
CN8503
PJ_TEMP_AD
PDATA0 - PDATA7
PDATA8 - PDATA15
PDATA16 - PDATA23
VSYNC_WE
HSYNC_CS
DATEN_CMD, PCLK
DPP_RESETZ
SDA_2601,SCL_2601
PARKZ
IC8701
SDRAM
(3/4)
MEM0_A0 - A12
MEM0_DQ0 - DQ15
MEMO_CLK_N/P
MEMO_BA0/BA1
MEMO_LDM/UDM
MEMO_LDQS/UDQS
MEMO_CASZ/RASZ/CSZ
MEMO_CKE/WEZ
H14
H13
J14
IC8605
DMD
CONTROL
(2/4)
DMD_D0 - D11
DMD_SAC_BUS
DMD_STRB/OEZ
DMD_LOADB/SCTRL
DMD_DCLK/BUS
K15
X8601
16.66667MHz
J15
LED_SEL0
LED_SEL1
SPIDIN_INT, SPIDOUT_INT
SPICS_INT, SPICLK_INT
BOARD
DMD_SAC_BUS
DMD_STRB/OEZ
DMD_LOADB/SCTRL
DMD_DCLK/BUS
RED_STROBE
BLU_STROBE
GRN_STROBE
DMD_D0 - D11
CN5503CN5505
IC8801
LED
DRIVE
(4/4)
25, 3,
7, 11,
13, 15,
23, 19,
8, 4,
14, 12
32
29, 36
20, 24
18, 28
LED_ANODE
RED_CATHODE
BLU_CATHODE
GRN_CATHODE
PJ_TEMP_AD
CN8502
1, 2
3, 4
9, 10
7, 8
6
PROJECTOR
UNIT
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-2
Page 44
4-3. OVERALL BLOCK DIAGRAM (3/5)( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
XLR UNIT
3
OVERALL (1/5)
(PAGE 4-1)
FP-1522 FLEXIBLE
BOARD
LCD_B_0-LCD_B_7
LCD_XVD
LCD_XHD
EVF_CLK_OUT
XPANEL_EVF_PS
XBB_RST
AV_ SO/ SCK
XCS_EVF
DAC_IOUT_Y
DAC_IOUT_PB
SDO
MCK_CN, LRCK_OUT,
BCK_CN
SDI0_SPDIF_IN_MAG
SDI1_MAG
XCS_IC_2801
XSYS_RST
SHOE_MIC_FL
SHOE_MIC_FR
MIC_JACK_IN
MIC_PWR_ON
HP_JACK_IN
JACK_AD
LANC_SIG
XEVF_SW
FR_XRESET
RH-014 BOARD
CN7001
37-44
34
33
31
35
29
46,47
48
2
3
16
11,13,12
14
15
10
9
22
21
MIC_JACK_IN
25
MIC_PWR_ON
26
HP_JACK_IN
24
JACK_AD
7
LANC_SIG
6
XEVF_SW
28
FR_XRESET
5
LCD_XVD
LCD_XHD
EVF_CLK_OUT
XPANEL_EVF_PS
XBB_RST
AV_ SO/ SCK
XCS_EVF
DAC_IOUT_Y
DAC_IOUT_PB
SDO
MCK_CN, LRCK_OUT,
BCK_CN
SDI0_SPDIF_IN_MAG
SDI1_MAG
XCS_IC_2801
AV_ SO/ SCK
XSYS_RST
SHOE_MIC_FL
SHOE_MIC_FR
VIDEO/AUDIO
PROCESSOR
K11
Q6401
IC2801
(2/5)
SE6401
EVF
PULL OUT
DETECT
(3/5)
LEVEL SHIFT
COMPO_VIDEO
AUDIO_L_I/O
AUDIO_R_I/O
HP_PRE_OUT_L
HP_PRE_OUT_R
HP_PS
MICAMP_OUT_L
MICAMP_OUT_R
EXT_LINE_SEL
INT_MIC_L
INT_MIC_R
INT_MIC_F
S7001
RESET
IC6403
(3/5)
4
IC6402
3
LEVEL SHIFT
IC2601
MIC/
HEADPHONE
AMP
(1/5)
(3/5)
EVF_PDB0-PDB7_CNLCD_B_0-LCD_B_7
9
10
AUDIO_L_I/O
AUDIO_R_I/O
HP_L_OUT
HP_R_OUT
EXT_MIC_L
EXT_MIC_R
EVF_VS_EVF
EVF_HS_EVF
EVF_CLK_OUT_EVF_CN
XBB_RST
AV_ SO/ SCK
XCS_EVF
COMPO_VIDEO
AUDIO_L_I/O
AUDIO_R_I/O
JACK_AD
LANC_SIG
HP_JACK_IN
INT_MIC_L
INT_MIC_R
INT_MIC_F
CN7005
CN7002
CN7004
8-11,
13-16
6
5
4
3
17,19
20
9
1
6
7
2
4
6
2
LCD902
COLOR
EVF
UNIT
A/V R
J7002
(HEADPHONE)
J7001
PLUG IN POWER
MIC901
MICROPHONE
UNIT
MIC (L)
MIC (R)
MIC (F)
INPUT 1
CN2202
INPUT 2
XL-013 BOARD HN-003 BOARD
IC2201
Q2201,Q2202
MIC
SWITCH
6
5
3
2
Q2203,Q2204
MIC
SWITCH
IC2203
LINE AMP
MIC AMP
5
6
3
2
Q2205,Q2208
ATTENUATOR
Q2331,Q2335
MIC CONTROL
SWITCH
AU_LINE_1
7
AU_LINE_2
1
MIC AMP
5
5
6
6
3
3
2
2
Q2206,Q2207
ATTENUATOR
Q2332,Q2336
MIC CONTROL
SWITCH
IC2202
CONTROL
SWITCH
BLOCK
(AU91000)
7
1
7
3
1
CN2201
AU_MIC_-1
AU_MIC_+1
ATT_1
XLR_MIC/LINE_1
AU_MIC_-2
AU_MIC_+2
ATT_2
XLR_MIC/LINE_2
10
11
23
21
8
2
4
5
24 1
20 3
15
14
17
23
21
20
6, 17
7,16
8, 14
5,10
3,12
4,11
19,20
CN1103
AU_MIC_-1
AU_MIC_+1
ATT_1
2
XLR_MIC/LINE_1
4
AU_LINE_1
AU_LINE_2
AU_MIC_-2
AU_MIC_+2
ATT_2
XLR_MIC/LINE_2
CN1102
2
XLR_MIC/LINE_1/2
XLR_PWR_ON_1/2
LEVEL_VOL_CH1/CH2
CH1/CH2_AUTO
ATT_1/2_OFF
ATT_1/2
REC_CH_SEL
LOWOUT_1/2_OFF
4
3
IC1101
MIC AMP
6
10
7
8
Q1103,Q1104
ATTENUATOR
SWITCH
90,91 93,94
ATT_2
ATT_1
CH1
CH2
CN1101
5
IC1001
MPU
7
ENCAPSULATED
CABLE
9
OVERALL (4/5)
(PAGE 4-4)
STROBE_ON
XSTRB_FULL
I2C_SDA/SCK
08
51
52
49,50
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
SYS_RST
STROBE_ON
XSTRB_FULL
I2C_SDA/SCK
D3
IC7201
LED FLASH
DRIVE
(5/5)
CN7003
LED1_3_K
LED2_K
FP-1555 FLEXIBLE
BOARD
18 -223 -7
TH
1
D0001
D0002
TH001
4-3
D0001, D0002
(LED FLASH)
: VIDEO SIGNAL
: AUDIO SIGNAL
Page 45
4-4. OVERALL BLOCK DIAGRAM (4/5)( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
9
OVERALL (3/5)
(PAGE 4-3)
MEMORY
PRO DUO
HOT SHOE
STICK
SD
FP-1523
FLEXIBLE
BOARD
LD-297 BOARD (1/2)
CN8001
MSX_BIO_0 - BIO_3
10,8,11,16
MSX_BS/CLK
7,17
MSX_INS_HIZ
14
SD_DAT_0 - DAT_3
21,23,1,3
SD_CMD/SDWP/CLK
6,15,26
CN4005
3
2
5
8
10
9
SD_XSDCD
SHOE_MIC_FL
SHOE_MIC_FR
HOTSHOE_ID1
HOTSHOE_ID2
LANC_SIG
EXT_STROBE_ON
24
CN4001
FP-1550
FLEXIBLE
BOARD
22,21,23,24
18,26
19
5,6,3,4
8,17,13
16
60
59
57
56
54
55
VC-658 BOARD (2/3)
CN1001
40,41,39,38
44,36
43
55 - 59
54,45,49
46
SHOE_MIC_FL
2
SHOE_MIC_FR
3
HOTSHOE_ID1
5
HOTSHOE_ID2
6
LANC_SIG
8
7
LANC_SIG
MSX_BIO_0 - BIO_3
MSX_BS/CLK
MSX_INS_HIZ
SD_DAT_0 - DAT_3
SD_CMD/SDWP/CLK
SD_XSDCD
4
EXT_STROBE_ON
6
OVERALL (1/5)
(PAGE 4-1)
OVERALL (1/5)
(PAGE 4-1)
D1401
D1402
IC1301
(2/3)
CPU,
AV SIGNAL PROCESS,
CAMERA DSP,
LENS CONTROL,
MODE CONTROL,
HIDMI PROCESS
(2/10-4/10)
AE16
MMC_DAT_0 - 7
MMC_CLK/CMD
GPS_UART_RXD
GPS_UART_TXD
GPS_UART_CTS
GPS_UART_RTS
XGPS_RST
CN1008
CN1005
(2/2)
CN1006
(2/2)
FP-1557
FLEXIBLE
BOARD
10-17
8,6
FP-1519
FLEXIBLE
BOARD
(2/2)
7
8
16
17
27
MM-102 BOARD
CN8101
7,5,3,9,8,6,4,2
11,13
(2/2)
CN6001 (2/2)
GPS_UART_RXD
25
GPS_UART_TXD
24
GPS_UART_CTS
16
GPS_UART_RTS
15
XGPS_RST
36
TE1_DAT_0-7
TE1_CLK/CMD
TE1_DAT_0-7
TE1_CLK/CMD
CN6101
2
4
1
3
88
FLEXIBLE
FLAT
CABLE
(FFC-254)
IC8101
INTERNAL
MEMORY
(1/2)
IC8201
INTERNAL
MEMORY
(2/2)
GP-037 BOARDPD-465 BOARD
CN9201
2
4
1
3
SCK0/TX0_1
SIN0/RX0_1
SO0/RTS_1
XSCS0/CTS_1
XGPS_RST
IC9204
GPS
RECEIVER
B3
E7
X9201
16.368MHz
GPS Model
SAW FILTER
IC9203
RF AMP
SF9202
AT9201
(GPS ANTENNA)
SF9201
SAW FILTER
IC9202
RF AMP
CONTROL
SWITCH
BLOCK
(RS39900)
LENS
BARRIER
UNIT
FR-319 BOARD
CN9602
1
5
6
(NIGHTSHOT)
CN9603
2
1
08
D9601
D9602
(TALLY)
DIAL_A
DIAL_B
KEY_AD3
Q9601
LED
DRIVE
IC9601
SIRCS
SHUTTER_A
SHUTTER_XA
CN9601
IR_LED_ON
XTALLY_LED
SIRCS_SIG
FP-1518
FLEXIBLE
BOARD
1
2
3
7
4
6
9,1011,12
CN4004
12
11
10
6
9
7
SHUTTER_A
3,41,2
SHUTTER_XA
DIAL_A
DIAL_B
KEY_AD3
IR_LED_ON
XTALLY_LED
SIRCS_SIG
CN4002
(1/2)
7
OVERALL (5/5)
(PAGE 4-5)
8
9
10
13
11
12
FP-1551
FLEXIBLE
BOARD
(1/2)
CN1002 (1/2)
54
53
52
49
51
50
8
OVERALL (5/5)
(PAGE 4-5)
DIAL_A
DIAL_B
KEY_AD3
IR_LED_ON
XTALLY_LED
SIRCS_SIG
XPANEL_POWER_ON
IC4801
(2/2)
HI CONTROL,
LANC INTERFACE
(9/10)
XCHARGE_LED
XCAM_LED
XPOWER_TACT_SW
CN1007
KEY_AD1
ZOOM_VR_AD
XCHARGE_LED
XCAM_LED
XPHOTO_LED
KEY_AD2
XPOWER_TACT_SW
ROLL_AD
VST_C_CHARGE
FP-1521
FLEXIBLE
BOARD
SS
3
2
4
6
10
9
13
14
16
18
CK-244 BOARD
CN9001
3
2
4
6
XCAM_LED
10
XPHOTO_LED
9
KEY_AD2
13
XPOWER_TACT_SW
14
ROLL_AD
16
VST_C_CHARGE
18
SS
KEY_AD1
ZOOM_VR_AD
XCHARGE_LED
S9001-S9005
IC7701
ROLL SENSOR
AMP
(1/2)
VIDEO/AUDIO SIGNAL
AUDIO SIGNAL
D9001
(MOVIE)
D9002
(PHOTO)
CN9002
SE7701
ROLL
SENSOR
(1/2)
4
8
2
6
CONTROL
SWITCH
BLOCK
(PS39900)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-4
Page 46
4-5. OVERALL BLOCK DIAGRAM (5/5)( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS BLOCK (2/2)
IRIS
DRIVE
ND
DRIVE
ZOOM
DRIVE
FOCUS
DRIVE
LENS TEMP
SENSOR
PITCH/YAW
DRIVE
OPTICAL IMAGE
STABILIZER
LD-297 BOARD (2/2) VC-658 BOARD (3/3)
FP-1551 FLEXIBLE
BOARD (2/2)
CN4003
19,28,
IRIS_A/B/XA/XB
18,29
IRF ±
11, 5
ND_DRIVE ±, ND_BIAS ±,
20,25,
ND_HALL±
23,22,
26,27
ZOOM_A/B/XA/XB_OUT
8, 9,
7,10
Z_MR_A/B
1,16
FOCUS ±
12,4
F_MR_A/B
14,2
LENS_TEMP_AD
15
PITCH ±_O
36-41
47,44,
PITCH_HALL± / BIAS-_O
46
YAW ±_O
30-35
YAW_ HAL L± / BIAS-_O
49,50,
48
PITCH ±_
O_OUT
YAW ±_
O_OUT
ZOOM_A/XA_OUT
ZOOM_B/XB_OUT
IC5602
PITCH
DRIVE
(3/5)
IC5603
YAW
DRIVE
(3/5)
IRIS DRIVE,
ND DRIVE,
ZOOM DRIVE,
FOCUS DRIVE
ZOOM MOTOR
ZOOM MOTOR
PITCH_INA/INB_O
PGOOD_XC_IC_5601
YAW_INA/INB_O
IC5201
(2/5)
IC5605
DRIVE
(3/5)
IC5606
DRIVE
(3/5)
D5
C7
ZM_ENB
ZM_DIR_A
ZM_DIR_B
ZM_ENB
IC5601
STEADYSHOT
PROCESSOR
(3/5)
IC_5201_PIO0/PIO1
IC_5201_PIO0/PIO1
IC_5201_VD
E3
IC_5601_IC_5201_CLK
F5
E4
IC_5201_SI/SO/SCK
IC_5601_IC_5201_CLK
IC_5601_SO/SI/SCK
IC_5601_P_LIMIT
IC_5601_2_EXPOSE
XIC_5601_CPU_RST
IC_5601_INT_REQ
XCS_IC_5601
CAM_V
CN4002
IR_FILTER_DIR/EN
XCS_IC_5201
IC_5201_VD
XIC_5201_RST
LENS_TEMP_AD
IRIS_ENB
IRIS_DIR_A/B
(2/2)
22,23
18,19,
20
17
44
57
60
27
29
25
28
40
42,41
51,50,
49
56
39
58
55
52
45
39,40
44,43,
42
45
18
5
2
35
33
37
34
22
20,21
11,12,
13
6
23
4
7
10
17
CN1002
(2/2)
IR_FILTER_DIR/EN
IC_5201_SI/SO/SCK
XCS_IC_5201
IC_5201_VD
XIC_5201_RST
IC_5601_IC_5201_CLK
ZM_ENB
ZM_DIR_A
LENS_TEMP_AD
ZM_DIR_B
IRIS_ENB
IRIS_DIR_A/B
IC_5601_SO/SI/SCK
IC_5601_P_LIMIT
IC_5601_2_EXPOSE
XIC_5601_CPU_RST
IC_5601_INT_REQ
XCS_IC_5601
CAM_V
AB17
AE9
AV SIGNAL PROCESS,
CAMERA DSP,
LENS CONTROL,
MODE CONTROL,
HDMI PROCESS
IC1301
(3/3)
CPU,
(2/10 - 4/10)
FP-1554 FLEXIBL
BOARD
SE001
PAN EL
OPEN/CLOSE
DETECT
XSYS_RST
8
59
32
31
56
XPANEL_POWER_ON
57
5
OVERALL (1/5)
(PAGE 4-1)
XMS_ACC_LED
LENSV_EN
LENS_COVER_DIR_PWM
PANEL_OPEN
CN4006
5, 6
PANEL_O/C_GMR
SE7501
PITCH /YAW
SENSOR
(4/5)
YAW_AD
PITCH_AD
7
OVERALL (4/5)
(PAGE 4-4)
SHUTTER_A
SHUTTER_XA
D1
LENS BARRIE
OPEN/CLOSE
IC5611
DRIVE
(3/5)
Q4002
PAN EL
DETECT
XSYS_RST
D8001
(ACCESS)
XMS_ACC_LED
LENS_COVER_DIR_PWM
LENSV_EN
PANEL_OPEN
XPANEL_POWER_ON
54
3
30
31
6
5
8
OVERALL (4/5)
08
(PAGE 4-4)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-5
Page 47
4-6. POWER BLOCK DIAGRAM (1/4) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
(DC JACK)
DC IN
BATTERY
TERMINAL
CHARGE
J901
+
S
–
CN9102
(USB)
VC-658 BOARD (1/3)
CN1011
ACV_UNREG_CN
2
BATT/XEXT_CN
3
REG_GND
1
BATT_UNREG_CN
4
BATT_SIG
5
REG_GND
6
CN9101
USB_VBUS_STD
1
USB_VCC
1
F009
Q4303, Q4304
BATTERY CHARGE
SWITCH
BATT/XEXT_CN
BATT_SIG
Q9102
B+
SWITCH
USB_VCC
D4301
MAIN_UNREG
IC9101
USB POWER
MANAGEMENT
(10/10)
OUT1
OUT2
VB1
A5
REG33
A6
VB2
B6
NVP
nENU
F500
VCC
IC9104
USB SWITCH
(10/10)
1D+
1
2D+
D+
IC9105
CURRENT LIMITER
(10/10)
EN
X_FAULT
OUT
IN
6
IC9103
USB SWITCH
(10/10)
F007
F006
Q4305
ACV/BATT SELECT
SWITCH
F002
BATT_UNREG
UNREG_IN_DET
IC9102
SMART POWER
SELECTOR
(10/10)
A1
VBUS1
A2
VBUS2
A3
ISNS
A5
VBUSLIM
PGOOD
VBUSOK
XVBUS_DET_STD_A
VBUS_XOVR_CUR
XVBUS_DET
D9103
NENU
D_2.8V
EVER_3.0V
VFB
E4
VFB
D4
SW2
D5
SW1
B5
A4
EN
B2
B4
USB_VBUS
VBUS_EN
D9102
L9101
USB_DD_PGOOD
USB_DD_EN
VBUSOK
J_5.0V
J_5.0V
A1
A2
C4
C1
B2
B1
3
8
3
4
1
D9101
Q9107
Q9103
F003
F004
F005
F001
INIT_CHARGE_ON
Q4801
DC JACK
DETECT
BATT_UNREG
XC_UNREG
CORE_UNREG
I/O_UNREG
MT_UNREG
ACV_UNREG
IC4801
HI CONTROL,
LANC INTERFACE
(9/10)
F10
O_INIT_CHARGE
PUI_BATT_XEXT
C7
A4
XPUIO_BATT_SIG
XO_CS_DDCON
O_LDO1.2_ON
O_LDO1.8_ON
O_NENU_ON
A5
O_SYS_DD_ON
OSYS_DD_ON_IC_4302
I_BATT_IN
H9
I_USB_CHG_READY
J10
XO_INIT_USB_CHG
B1
I_USB_BATT_IN
XO_CS_IC_4302
XO_LANC_IC_ON
XPUI_LANC_PWR_ON
BATT_ON
ACV_ON
XCS_DD
G1 G6
LDO1_ON
D3
LDO2_ON
C4
DD_ON
F2
SYS_DD_ON_IC_4302
Q4301
ACV
DETECT
ACV_ON
BATT_ON
A7
H2
C1
BATT_IN
VOUT
XCS_IC_4302
XLANC_ON
XLANC_PWR_ON
Q4302
BATT
DETECT
UNREG_IN_DET
E1
PVDD1a
E2
PVDD1b
C8
PVDD2
A1
PVDD3a
B1
PVDD3b
H6
PVDD4
PVDD5a
H5
PVDD5b
G5
PVDD_CP
H2
AVDD
B7
DC/DC CONVERTER
D8
PVDD6a
D7
PVDD6b
CS
D6
LDO1_ENB
E5
LDO2_ENB
F5 DD_ON
DC/DC CONVERTER,
LANC DRIVER
E6
VTR_UNREG
A4
PVDD_LPO2
LDO1_ON
C1
D2F1
DD_ON
F1
ACV_UNREG
ACV_ON
E2
BATT_ON
D1
E4
UNREG_IN
F5
VuC
E3K9
CS
C2
XLANC_ON
C4
XLANC_PWR_ON
UNREG_IN_DET
F2
E1
BATT_UNREG
LX1a
LX1b
LDO1_SOURCE
LDO2_SOURCE
IC4301
(8/10)
LX6a
LX6b
LDO1_OUT
LDO2_OUT
IC4302
(8/10)
PVDD_LDO1
LDO1_OUT
LDO1_FB
LDO2_OUT
LDO2_ON
LOAD_IN
LOAD_OUT
LOAD_ON
LANC_DC
EVER3
Q4306,Q4307
B+ SWITCH
L4301
D1
D2
FB1
D3
LX2
FB2
LX3a
LX3b
FB3
LX4
FB4
LX5a
LX5b
FB5
FB6
VCH
L4302
B8
A6
C5
L4303
A2
B2
C4
B4
L4304
H7
E4
L4305
H4
G4
E3
L4306
E8
E7
D5
HB_1.2V
A5
HB_1.8V
A4
D_1.2V
B1
A_1.125V
A1
A_1.125V_SENSE
B2
HDMI_5V
A3
A5
B6
MSX_3.3V
A6
MS_PWR_ON
B5
LANC_DC LANC_DC
D6
BATT_LI_3V
F4
EVER_3.0V
F6
SHOE_ON
CH1_OUT
CH2_OUT
CH3_OUT
CH4_OUT
CH5_OUT
D_3.3V
SD_PWR_ON
CH6_OUT
F008
MT_5.0V
LCD_CABC_PWM
SD_PWR_ON
LCD_CABC_PWM
SHOE_ON
MS_PWR_ON
USB_VBUS
VBUS_EN
VBUS_XOVR_CUR
XVBUS_DET_STD_A
XVBUS_DET
IC4304
B+ SWITCH
(8/10)
1
VIN
VOUT
5
EN
3
IC4303
BL DREIVE
(8/10)
6
VIN
L4307
VOUT
1
LX
EN
4
CPU, AV SIGNAL PROCESS,
CAMERA DSP, LENS CONTROL,
MODE CONTROL, HDMI PROCESS
(2/10 - 4/10)
FRC_RTG_IN1
AF10
LCD_CABC_PWM
Y10
IRIS1
A16
GPIO_S__6
P24
USB_VBUS
AJ20
AE21
VBUS_EN
GPIO_S__2
R25
GPIO_SB__5
T25
GPIO_S__1
R26
FB
IC1301
(1/2)
5
3
SD_VCC
BL_H
BL_L
HB_1.2V
HB_1.8V
HB_1.2V
HB_1.8V
SHOE_UNREG
L4308
EVER_3.0V
D_2.8V
XC_UNREG
A_VID_1.1V
D_VID_1.1V
D_1.2V
A_1.8V
D_1.8V
A_2.8V
D_2.8V
A_3.3V
D_3.3V
SD_VCC
J_5.0V
MT_5.0V
BL_H,BL_L
A_1.125V
HDMI_5V
MSX_3.3V
BATT_LI_3V
EVER_3.0V
J_5.0V
A
POWER (2/4)
(PAGE 4-7)
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-6
Page 48
4-7. POWER BLOCK DIAGRAM (2/4) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-658 BOARD (2/3)
A
POWER (1/4)
(PAGE 4-6)
B
POWER (3/4)
(PAGE 4-8)
A_1.125V
A_1.8V
A_2.8V
A_3.3V
D_1.2V
D_1.8V
D_2.8V
D_3.3V
A_VID_1.1V
D_VID_1.1V
EVER_3.0V
HDMI_5V
J_5.0V
MSX_3.3V
MT_5.0V
BATT_LI_3V
BL_H,BL_L
LANC_DC
SD_VCC
SHOE_UNREG
XC_UNREG
A_2.8V
A_3.3V
D_1.2V
D_1.8V
D_2.8V
D_3.3V
EVER_3.0V
HDMI_5V
MSX_3.3V
MT_5.0V
SDD_VCC
SHOE_UNREG
XC_UNREG
IC1301
(2/2)
CPU,
AV SIGNAL PROCESS,
CAMERA DSP,
LENS CONTROL,
MODE CONTROL,
HDMI PROCESS
(2/10 - 4/10)
FRC_RTG_OUT0
GPIO_S__4
A_1.8V
A_1.8V
D_1.8V
D_2.8V
MT_5.0V
D_1.2V
D_2.8V
A_1.8V
AE9
P26
L2701
A_2.8V_IC_1301
AVDD18_SUBL
MMC_VCC
XIC_5201_RST
MMC_PWR_ON1
IC1302
CLOCK
GENERETOR
(2/10)
IC2701
D/A CONVERTER,
SPEAKER AMP
(5/10)
IC3001
AUDIO DSP
(6/10)
IC3301
LCD SERIAL
INTERFACE
TRANSMITTER
(7/10)
PJ_PWR_EN
L1301
POWER (3/4)
(PAGE 4-8)
A_1.125V
A_2.8V
A_3.3V
D_1.2V
D_1.8V
D_2.8V
D_3.3V
SD_VCC
A_VID_1.1V
D_VID_1.1V
A_1.8V
C
BL_H, BL_L
D_1.8V
MT_5.0V
D_3.3V
PJ_PWR_EN
D_2.8V
CN1003
J_5.0V
A_2.8V
D_1.8V
EVER_3.0V
BATT_LI_3V
LANC_DC
CN1005
CN1006
18,19
25
12-14
6
4
26
1-4
44
9
35
43
FP-1519
FLEXIBLE
BOARD
FP-1522
FLEXIBLE
BOARD
PD-465 BOARD
CN6001
14,13
A_1.8V
7
EP_2.8V
37
LCD SERIAL
INTERFACE
RECEIVER
A_5.0V
18,19,20
D_3.3V
26
PJ_PWR_EN
28
RH-014 BOARD
CN7001
J_5.0V
58-61
A_2.8V
18
D_1.8V
53
EVER_3.0V
27
BATT_LI_3V
19
LANC_DC
854
IC6101
(2/2)
BL_H, BL_L
GPS Model
IC6102
2.8V REG
(2/2)
4
VDD
1
CE
SE6401
EVF PULL OUT
DETECT
(3/5)
BT7001
LITHIUM
BATTERY
L6002
SE6001
PANEL
NORMAL/REVERSE
DETECT
(1/2)
Q6001, Q6002
TOUCH
PANEL
INTERFACE
PJ_PWR_EN
3
Vout
AU_2.8V
D_2.8V
A_2.8V
CN6003
L6001
CN6007
A_5.0V
D_3.3V
CN6101
D_3.3V
D_2.8V
L2802
(LCD MODULE)
61,60
WIDE COLOR
29,30
10,22
LCD BACKLIGHT
PJ-104 BOARD
CN8503
PJ_SYSPWR
4,6,8,10
4,6,8,10
20
20
18
18
FLEXIBLE
FLAT CABLE
(FFC-254)
7
6
L2601
L2602
AU_2.8V_IC_2801
L2803
L2804
LCD901
3.0 INCH
LCD
VFLASH
POWER_EN
VFLASH
IC8501
INVERTER
(1/4)
5
OUTYVCC
INA
IC8603
FLASH MEMORY
(2/4)
DMD_PWR_EN
IC8605
DMD CONTROL
(2/4)
IC8801
LED DRIVE
(4/4)
GP-037 BOARD
CN9201
D_3.3V
7
D_2.8V
6
IC2601
MIC/
HEADPHONE
AMP
(1/5)
IC2801
VIDEO/AUDIO
PROCESSOR
(2/5)
DMD_EN
4
DMD_PWR_EN
1
K14
L9201
L9202
D_1.8V
P1P0V
P1P8V
P1P8V
L7201
D_2.8V
IC6402
LEVEL SHIFT
(3/5)
L8504
PJ_SYSPWR
2
TX1/I2CC/GIO14
RECEIVER
4
1
IC8502
POWER CONTROL
(1/4)
SW
VOUTA
7
VOUTB
VINB
8
11
ENA
ENB
4
IC8503
POWER CONTROL
(1/4)
VIN1
8
3
VIN2
1
EN1
EN2
6
IC8701
SDRAM
(3/4)
IC9201
2.8V REG
1
VOUT
VIN
3
ON_OFF
IC9204
GPS
IC6401
2.5V REG
(3/5)
VDD
VOUT
CE
IC7201
LED FLASH
DRIVER
(5/5)
IC6403
LEVEL SHIFT
(3/5)
VINA
LX2
LX1
L9214
G2
3
EP_2.5V
D8501,D8502
RESET
2
9
10
L8501
5
L8503
10
IC8602
INVERTER
(2/4)
EP_2.5V
EP_2.5V
VOUT_LED_A
LANC_DC
P1P8V
P1P0V
CN7005
J_5.0V
CN7003
CN7002
DMD_VRST
DMD_VOFS
DMD_VBIAS
IC8601
LED DECODER
(2/4)
IC9202
RF AMP
IC9203
RF AMP
22
1
FP-1555 FLEXIBLE
BOARD
8-17
4
CN8501
COLOR EVF
D0001, D0002
(LED FLASH)
A/V R
LCD902
UNIT
FP-1582
FLEXIBLE
BOARD
CN5505
39
39
30
30
31
31
1,2,21,22,41,42
1,2,21,22,41,42
DMD_VRST
DMD_VOFS
DMD_VBIAS
P1P8V
CN5503
39
30
31
1,2,21,22,41,42
PROJECTOR UNIT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-7
Page 49
4-8. POWER BLOCK DIAGRAM (3/4) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CONTROL
SWITCH
BLOCK
(PS39900)
CK-244 BOARD
CN9002
D_2.8V
1
EVER_3.0V
5
D9001
(MOVIE)
D9002
(PHOTO)
ROLL SENSOR
SE7701
(1/2)
HDMI
FP-1521
FLEXIBLE
BOARD
CN9001 CN1007
D_2.8V
A_2.8V
11
7
19
EVER_3.0V
L7701
VC-658 BOARD (3/3)
B
POWER (2/4)
(PAGE 4-7)
CN1009
HDMI_5.0V
18
D_2.8V
11
EVER_3.0V
7
A_2.8V
19
A_2.8V
A_3.3V
D_1.2V
D_1.8V
D_2.8V
D_3.3V
EVER_3.0V
MT_5.0V
MSX_3.3V
SHOE_UNREG
SDD_VCC
XC_UNREG
HDMI_5V
CN1002
A_3.3V
D_1.2V
D_1.8V
D_2.8V
EVER_3.0V
XIC_5201_RST
CN1001
MT_5.0V
FP-1551
FLEXIBLE
BOARD
46
24
29
28
58
5
FP-1550
FLEXIBLE
BOARD
LD-297 BOARD
CN4002
A_3.3V
16
D_1.2V
38
D_1.8V
33
D_2.8V
34
EVER_3.0V
4
XIC_5201_RST
57
CN4001
MT_5.0V
MT_5.0V
D_2.8V
ZOOM MOTOR
IC5202
4
1
CE
IRIS DRIVE, ND DRIVE,
IC5602
PITCH
DRIVE
(3/5)
IC5605
DRIVE
(3/5)
(2/5)
VOUTVDD
IC5201
FOCUS DRIVE,
ZOOM DRIVE
(2/5)
IC5603
YAW
DRIVE
(3/5)
ZOOM MOTOR
3
IC5606
DRIVE
(3/5)
MR_A_2.8V
IC5601
STEADYSHOT
PROCESSOR
GPIO6/I2C_SCL
LENS BARRIER
(3/5)
IC5611
DRIVE
(3/5)
MR_A_2.8V
PGOOD_XC
F10
CN40032.8V REG
SE7501
PITCH/ YAW
SENSOR
(4/5)
3,17,45,51
LENS
BLOCK
CM-121 BOARD
IC6701
CMOS
IMAGER
A_2.7V
MM-102 BOARD
IC8201
INTERNAL
MEMORY
(2/2)
08
D_1.5V
3
TE1_VCC
IC6706
1.5V REG
OUTCEIN
IC8101
INTERNAL
MEMORY
(1/2)
4
1
VOUTCEVDD
3
2.9V REG
IC7701
ROLL SENSOR
AMP
(1/2)
3
IC8701
(1/2)
IC6703
2.7V REG
OUTCEIN
4
1
D_1.8V/D_2.8V
I/O_1.8V
CMOS_A_3.3V
4
1
MEDIA_3.3V
MMC_PWR_ON1
TE1_VCC
CN6701
CN8101
FP-1520
FLEXIBLE
BOARD
51
50
49
FP-1557
FLEXIBLE
BOARD
17,18
12
16
15
51
50
49
12
3
4
CN1004
CN1008
1,2
D_1.8V
AVDD18_SUBL
A_3.3V
D_3.3V
MMC_PWR_ON1
MMC_VCC
XIC_5201_RST
AVDD18_SUBL
MMC_PWR_ON1
MMC_VCC
XC_UNREG
SHOE_UNREG
MSX_3.3V
SD_VCC
C
POWER (2/4)
(PAGE 4-7)
17-2410-13 28-31
33,3451,52
XC_UNREG
38-45
SHOE_UNREG
49-52 31-3428,2910,11
MSX_3.3V
SD_VCC
XIC_5201_RST
D_2.8V
XC_UNREG
D8001
(ACCESS)
2
3
2
3
IC5609
7.0V REG
(3/5)
IN
EN
IC5610
7.0V REG
(3/5)
IN
EN
VOUT
VOUT
XCON_7.0V_OUTXC_UNREG
9
PGOOD_XC
PG
5
FP-1523
FLEXIBLE
BOARD
CN4005
9
SHOE_XC_7V
MSX_3.3V
SD_VCC
CN8001
SHOE_UNREG
6, 7
19
12
FP-1518
HOT
SHOE
MEMORY
STICK
PRO DUO
SD
FR-319 BOARD
D
POWER (4/4)
(PAGE 4-9)
FLEXIBLE
CN4004
D_2.8V
BOARD
8
5
CN9601
D_2.8V
IC9601
SIRCS
D9601
(NIGHTSHOT)
D9602(TALLY)
FP-1554FLEXIBLE
BOARD
CN4006
EVER_3.0V
EVER_3.0V
1,2
SE001
PANEL
OPEN/CLOSE
DETECT
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-8
Page 50
4-9. POWER BLOCK DIAGRAM (4/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
XLR UNIT
D
POWER (3/4)
(PAGE 4-8)
HOT
SHOE
HN-003 BOARD XL-013 BOARD
FLEXIBLE
FLAT CABLE
(FFC-116)
08
CN1101
2
XLR_UNREG
IC1002
4.0V REG
Vin
43
IC1003
DC/DC CONVERTER
D1002
CHARGE
PUMP
Vout
EXT
VDD
CE
AU_+4V
Q1001, Q1002
SWITCHING
5
2
3
AU_-9V
IC1004
6.0V REG
AU_+9V
IN OUT
54
IC1101
MIC AMP
IC1001
MPU
Q1101,
Q1102
POWER
SWITCH
CN1103
AU_+6V
XLR_PWR_ON_1/2
CN1102
AU_AD
10,11
6, 5
7
12 13
9,15 7,16
CONTROL
SWITCH
BLOCK
(AU91000)
CN2201
XLR_UNREG
14,15
XLR_PWR_ON_1/2
19,20
AU_+6V
18
AU_-9V
Q2302, Q2303
EaIn
IC2201
MIC AMP
SWITCHING
1
IC2301
DC/DC CONVERTER
VCC OUT
35
Q2331,Q2332
MIC CONTROL
SWITCH
IC2202
MIC AMP
Q2304-Q2307
+48V
SWITCH
IC2203
LINE AMP
AU_+48V_CH1
AU_+48V_CH2
CN2202
INPUT1
INPUT2
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
4-9E
Page 51
5-1. FRAME SCHEMATIC DIAGRAM (1/2)
5. FRAME SCHEMATIC DIAGRAMS
D0001, D0002
LED FLASH
LCD902
COLOR
EVF
UNIT
D001
D002
CN7005
122
RH-014 BOARD
(SIDE A)
16
CN7004
S9004
NIGHTSHOT
S9001
POWER
FP-1555 FLEXIBLE BOARD
RH-014 BOARD
(SIDE B)
14
12
J7001
J7002
13
108
6
579
42
13
11
CN7002
BT7001
LITHIUM
BATTERY
PLUG IN
POWER
(HEADPHONE)
MIC901
MICROPHONE
UNIT
A/V R
CK-244 BOARD
(SIDE A)
S9003 S9005 S9002
LIGHT
CN7003
122
PROJECTOR
61
60
CN7001
2
1
S9006
MODE
S7001
RESET
CONTROL
SWITCH
BLOCK
(PS39900)
CN9002
110
CK-244
BOARD
(SIDE B)
22
1
61
FP-1522 FLEXIBLE BOARD
1
CN9001
FP-1521 FLEXIBLE
201
BOARD
XLR UNIT
A
120
120
J901
DC JACK
BATTERY
TERMINAL
DC IN
HN-003 BOARD (SIDE B)
VC-658
BOARD
(SIDE A)
CN1007
20 1
62
1
16163
2
IC1301
(Not supplied)
CN1003
61
60
118
CN1008
250
151
CN1004
CN1011
61
15
CN9101
67
BUILT-IN
USB CABLE
CHARGE
FP-1523 Flexible
HOT SHOE
(PAGE 5-2)
ENCAPSULATED
CABLE
CN1101
18
HN-003
BOARD
(SIDE A)
XL-013 BOARD (SIDE A)
CN2202
INPUT1INPUT2
CONTROL
SWITCH
BLOCK
(AU91000)
CN1102
20
241
CN1103
(FFC-116)
Flexible Flat Cable
CN2201
24 1
IC2301
(Not supplied)
1
CN1001
18
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
MM-102 BOARD
(SIDE A)
CN8101
118
1
18
FP-1557 FLEXIBLE
BOARD
5-1
CM-121
BOARD
(SIDE B)
CM-121
18
1
250
CN6701
1
51
BOARD
(SIDE A)
Page 52
5-2. FRAME SCHEMATIC DIAGRAM (2/2)
PROJECTOR
UNIT
FP-1518 FLEXIBLE BOARD
1
12
FR-319
BOARD
(SIDE A)
FP-1582 FLEXIBLE
BOARD
CN5505
CN5503
141 4345
242 4446
FR-319
BOARD
(SIDE B)
CN9602
6
5
CN9603
2
1
2
CN9601
12
1
2
1
11
45
46
42
2
141
44
43
PJ-104 BOARD
(SIDE B)
43
44
2
1
41
42
45
46
110
CN8502
CN8501
PJ-104 BOARD
(SIDE A)
IC8605
(Not supplied)
CN8503
2
1
60
59
GPS Model
GP-037 BOARD (SIDE B)
18
CN9201
Flexible Flat Cable (FFC-254)
CN6007
2
1
CN6001
59
PD-465 BOARD
60
60
61
1
2
CN6005
SP901
(SPEAKER) (L)
SP902
(SPEAKER) (R)
CN6004
81
CN6101
61
CN6003
260
1
21
CN6002
16
78
LCD901
(LCD MODULE)
TOUCH
PAN EL
3.0 INCH
WIDE COLOR
LCD
BACKLIGHT
FP-1523 FLEXIBLE
BOARD
1
12
1
16
HOT SHOE
A
HN-003
CN1101
(PAGE 5-1)
1
2
LENS BLOCK
LD-297
BOARD
(SIDE B)
51
CN4003
1
12
161
1
CN4004
12
126
29 30
1
250
CN8001
28 27
LD-297
BOARD
(SIDE A)
CN4006
1
6
CN4005
12
1
6
1
SE7501
(PITCH/YAW)
602
602
61
63
CN4001
62
1
61
63
CN4002
62
1
1
FP-1550 FLEXIBLE
BOARD
61
1
FP-1551
FLEXIBLE
BOARD
61
VC-658 BOARD (SIDE B)
CN1010
1
CN1001
61
62
1
CN1002
61
63
1
6
62
2
60
63
2
60
33
CPC
(FOR CHECK)
61
1
61
1
CN1005
21
20
119
CN1009
8
CN9102
6
1
33
CN1006
232
232
HDMI
23
22
9
7
(USB)
1
CONTROL
SWITCH
BLOCK
LENS
BARRIER
UNIT
(RS39900)
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
FP-1519 FLEXIBLE BOARD
5-2E
FP-1554 FLEXIBLE BOARD
1
33
1
33
Page 53
6. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
– ENGLISH – – JAPANESE –
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
(In addition to this, the necessary note is printed in each block)
For Schematic Diagrams
• All capacitors are in μF unless otherwise noted. pF :
μF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor,
Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A 2520
Kinds of capacitor External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve
B, unless otherwise noted.
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
•
•
•
•
•
•
•
When indicating parts by reference number, please include the board name.
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
: non flammable resistor
: fusible resistor
: panel designation
: B+ Line
: B– Line
: IN/OUT direction of (+, –) B LINE.
: adjustment for repair.
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
For Printed Wiring Boards
•
: Uses unleaded solder.
•
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram isn’t
mounted in this model.
•
: panel designation
• Chip parts.
Transistor Diode
C
EB
654
46
123
3152
21
12
345
534
54
45
21321321
123
312
23
14
43
12
回路図，プリント図共通ノート
（他に必要なノートは各セクションに記載しています）
回路図ノート
・ ケミコン，タンタルを除くコンデンサで，耐圧50V以下の
ものはその耐圧を省略。単位はすべてμF（pはpF）。
・ チップ抵抗で指示のないものは，1/10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・ チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用く
ださい。
タンタルコンデンサのマイナス側は熱に弱いため注意し
てください。
・ チップ部品には下記のように表示したものがあります。
例 C541 L452
22U 10UH
TA A 2520
3
43
12
23
14
31
種類 外形寸法（mm）
ケースサイズ
4625
654
46
・ 抵抗，コンデンサ，ICなど定数にXXがあるものは，使用
していない事を示しています。このため，使用していな
い回路が記載されている事があります。
123
3152
・ ★印のある部品は，機種などにより異なりますので機能
別マウント一覧表を参照してください。
・ 可変抵抗と半固定抵抗で，B特性の表示を省略。
・ 信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・ は不燃性抵抗。
・ はヒューズ抵抗。
・ はパネル表示名称。
・ はB＋ライン。
・ はB−ライン。
・ はBライン（＋，−）の入出力方向を示す。
・ は調整名称。
イメージャ交換時の注意
・ イメージャを交換した場合は，カメラ部の全調整を行って
ください。
・ イメージャは構造上，静電気により破壊される恐れがある
ため，MOSICと同様に注意して取り扱ってください。
また，受光部にはゴミの付着，および強い光がはいること
のないように注意してください。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
印の部品，または0印付の点線で囲まれた部品は，
0
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してください。
プリント図ノート
・ ：無鉛半田を使用しています。
・ ：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・ スルーホールは省略。
・ プリント図には，本機で使用していない部品が記載され
ている場合があります。
・ はパネル表示名称。
• Chipparts.
Transistor Diode
C
EB
654
46
123
3152
21
12
345
534
54
45
21321321
123
312
23
14
43
12
23
14
3
43
12
31
4625
654
46
123
3152
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-1
Page 54
6-1. SCHEMATIC DIAGRAMS
12345 6 7 8 9
A
B
C
D
E
F
I/O_1.8V
REG_GND
D_1.8V/D_2.8V
REG_GND
D_1.5V
A_2.7V
R6701
A_2.7V
R6706
XX
C6713
R6707
47k
C6718
C6714
2.2u
B4
D6
D5
VRL
VCP
VBO
IMX077LHK-13
CMOS IMAGER
C6736
10u
R6767
A2
C6731
XX
1u
2.2u
C6
J3NCC5
VHI
IC6701
C6716
0.1u
C6715
2.2u
C6717
XX
R6741
XX
R6743
XX
VEXRES
0.1u
C6719
2.2u
D8
VBGR
A10NCD2
C6721XXC6722
C6720
2.2u
B10NCD7
G3NCB5
B6NCH3
ASMON1C7ASMON2
VLOADLM1
VLOADLM2
XCLRJ1XVSH1XHSD3XCED1SCKC2SDIC1SDOJ2INCK
C6723XXC6724XXC6725
XX
CMOS_A_3.3V
REG_GND
L2
K2
K1
TOUT
TENABLE
TSCANEN
NC
B9
NC
B2
XX
D_1.8V/D_2.8V
DCKP
DCKM
DOJP
DOJM
DOHP
DOHM
DOGP
DOGM
DOFP
DOFM
DOEP
DOEM
DODP
DODM
DOCP
DOCM
DOBP
DOBM
DOAP
DOAM
I/O_1.8V
DOIP
DOIM
D_1.5V
F10
F9
A8
A7
B8
B7
C10
C9
D10
D9
E10
E9
G10
G9
H10
H9
J10
J9
K8
K7
L8
L7
NC
B1
R6737 XX
R6710 XX
R6711 XX
R6712 XX
R6713 XX
R6714 XX
R6708 1k
C6735
C6726
XX
XX
R6745
R6746
R6738
R6739
R6770
R6768
DCKP
DCKM
DOJP
DOJM
DOIP
DOIM
DOHP
DOHM
DOGP
DOGM
DOFP
DOFM
DOEP
DOEM
DODP
DODM
DOCP
DOCM
DOBP
DOBM
DOAP
DOAM
INCK
SDO
SDI
SCK
XCE
XHS
XVS
XCLR
REG_GND
XX
XX
IC6705
XX
IC6702
IC6706
1.5V REG
MM3404A15URE
C6734
C6730
C6738
R6747
XX
XX
R6740
XX
XX
R6769
XX
1u
XX
C6733
XX
XX
C6727
XX
XX
C6737
34
IN
XX
XX
1u
OUT
GND
34
OUT
GND
34
OUT
GND
CE
12
IN
CE
12
IN
CE
12
D_1.8V/D_2.8V
I/O_1.8V
CMOS_A_3.3V
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
DOAP
DOAM
DOBP
DOBM
DOCP
DOCM
DODP
DODM
DOEP
DOEM
DCKP
DCKM
DOFP
DOFM
DOGP
DOGM
DOHP
DOHM
DOIP
DOIM
DOJP
DOJM
XVS
XHS
SDI
XCE
SDO
SCK
XCLR
INCK
I/O_1.8V
CMOS_A_3.3V
REG_GND
D_1.8V/D_2.8V
1
LF6701
3
XX
1
LF6702
3
XX
1
LF6703
3
XX
1
LF6704
3
XX
1
LF6705
3
XX
1
LF6706
3
XX
1
LF6707
3
XX
1
LF6708
3
XX
1
LF6709
3
XX
1
LF6710
3
XX
1
LF6711
3
XX
R6709 XX
Note: IC6701 and CM-121 COMPLETE BOARD are
not supplied, but they are included in CMOS
BLOCK ASSY (1390)-077.
51 D_1.8V
50 IO_1.8V
49 CMOS_A_3.3V
48 REG_GND
47 REG_GND
2
46 SUBL_DINP1
4
45 SUBL_DINN1
44 REG_GND
2
43 SUBL_DINP2
4
42 SUBL_DINN2
41 REG_GND
2
40 SUBL_DINP3
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
SUBL_DINN3
39
38 REG_GND
37 SUBL_DINP4
36 SUBL_DINN4
35
REG_GND
34 SUBL_DINP5
33 SUBL_DINN5
32 REG_GND
31 SENSE_CLK_N
30 SENSE_CLK_P
29 REG_GND
28 SUBL_DINP6
27 SUBL_DINN6
26 REG_GND
25 SUBL_DINP7
24 SUBL_DINN7
23 REG_GND
22 SUBL_DINP8
21 SUBL_DINN8
20 REG_GND
19 SUBL_DINP9
18 SUBL_DINN9
17 REG_GND
16 SUBL_DINP10
15 SUBL_DINN10
14 REG_GND
13 REG_GND
12 SENS_VD
11 SENS_HD
10 SENSSO
9SENSXCE
8 SENSSI
7 REG_GND
6SENSSCK
5 REG_GND
4 VFLASH_RST
3 REG_GND
2 CLK_CMOS_IN
1 REG_GND
CN6701
51P
CM-121 BOARD
CMOS IMAGER
XX MARK: NO MOUNT
VC-658
(1/10)
CN1004
Through the FP-1520
Flexible Board
(PAGE 6-9)
A
B
C
D
E
F
C6707
2.2u
C6706
0.1u
R6702
R6703
R6704
C6703
C6702
L1
0.1u
0.1u
C6701
0.22u
XX
C6704
10u
XX
C6705
10u
XX
R6793
R6742
R6744
NC
H4
VDDLIO1
E8
VSSLIO1
H5
VDDLIO2
F8
VSSLIO2
G8
VSSLIO3
H7
VSSLIO4
H6
VSSLIO5
J7
VSSLIO6
J6
VSSLIO7
J5
VSSLIO8
L3
NC
F2
VDDLCM1
E2
VSSLCM1
K4
VDDLCM2
J4
VSSLCM2
L4
NC
D4
VDDLCN1
C4
VSSLCN1
L5
VSSLCN2
L6
VDDLCN2
L9
NC
NC
L10
C6708
1u
XX
XX
C6728
3IN4
1u
C6732
XX
XX
OUT
B1
XX
C6711
0.1u
C6712
0.001u
K9NCG2
H2
K10NCF3
E3
K6
K5
VSSLPL
VDDLPL
VSSLSC1
VSSLSC2
VDDLSC1
VDDLSC2
VDDHDAA4VSSHDAB3VDDHCPC3VSSHCPA1NCF1VDDHCM1G1VSSHCM1H8VDDHCM2J8VSSHCM2A2NCA5VSSHPXA6VDDHPXA9NCE1VDDSUBA1C8VDDSUBA2K3VDDSUBD
A3
C6709
0.1u
C6710
2.2u
R6705
XX
OUT
IC6703
GND
2.7V REG
MM3404A27URE
1CE2
C6729
1u
A1
GND
IC6704
Cont
XX
IN
B2
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-2
Page 55
12345 6 7 8 9
62
REG_GND
REG_GND
XIC_5201_RST
XSYS_RST
REG_GND
XCS_IC_5601
IC_5601_SI
IC_5601_SO
IC_5601_SCK
REG_GND
REG_GND
REG_GND
CAM_V
IC_5201_VD
REG_GND
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
REG_GND
REG_GND
REG_GND
REG_GND
LENSV_EN
ZM_DIR_A
ZM_DIR_B
ZM_ENB
REG_GND
REG_GND
IR_FILTER_DIR
IR_FILTER_EN
REG_GND
IC_5201_SCK
IC_5201_SO
IC_5201_SI
XCS_IC_5201
REG_GND
REG_GND
IR_LED_ON
SIRCS_SIG
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
REG_GND
PANEL_OPEN
EVER_3.0V
XMS_ACC_LED
REG_GND
REG_GND
LND002
D_1.2V
D_2.8V
D_1.8V
A_3.3V
63
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
61P
IC_5601_IC_5201_CLK
XIC_5601_CPU_RST
XIC_5201_RST
IC_5601_P_LIMIT
IC_5601_INT_REQ
XSYS_RST
XCS_IC_5601
IC_5601_SI
IC_5601_SO
IC_5601_SCK
CAM_V
IC_5201_VD
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
IC_5601_2_EXPOSE
D_1.2V
D_2.8V
D_1.8V
LENS_COVER_DIR_PWM
LENSV_EN
ZM_DIR_A
ZM_DIR_B
ZM_ENB
IR_FILTER_DIR
IR_FILTER_EN
IC_5201_SCK
IC_5201_SO
IC_5201_SI
XCS_IC_5201
A_3.3V
IR_LED_ON
SIRCS_SIG
XTALLY_LED
DIAL_B
DIAL_A
PANEL_OPEN
XPANEL_POWER_ON
EVER_3.0V
XMS_ACC_LED
REG_GND
C4005
CN4003 51P
Z_MR_A
F_MR_B
MR_A_2.8V
FOCUS-
IRF-
REG_GND
ZOOM_XA_OUT
ZOOM_A_OUT
ZOOM_B_OUT
ZOOM_XB_OUT
IRF+
FOCUS+
F_MR_A
LENS_TEMP_AD
Z_MR_B
IRIS_XA
IRIS_A
ND_DRIVE+
ND_HALL-
ND_HALL+
ND_DRIVE-
ND_BIAS+
ND_BIAS-
YAW+_O
YAW-_O
PITCH+_O
PITCH-_O
MR_A_2.8V
PITCH_BIAS-_O
YAW_BIAS-_O
YAW_HALL+_O
YAW_HALL-_O
D_2.8V
IRIS_B
IRIS_XB
CL4001
R4009
D_2.8V
R4006
47k
LENS_TEMP_AD
C4004
XX
REG_GND
D_2.8V
R4008
10k
R4007
XX
XX
KEY_AD3
REG_GND
PITCH_HALL-_O
PITCH_HALL+_O
1
Z_MR_A
2
F_MR_B
3
F_MR_VCC
4
FOCUS(-)
IRF(-)
5
GND
6
ZOOM_XA
7
ZOOM_A
8
ZOOM_B
9
ZOOM_XB
10
IRF(+)
11
FOCUS(+)
12
GND
13
F_MR_A
14
L_TEMP_OUT
15
16
Z_MR_B
Z_MR_VCC
17
IRIS_XA
18
IRIS_A
19
20
ND_DRIVE(+)
GND
21
ND_HALL(-)
22
ND_HALL(+)
23
GND
24
ND_DRIVE(-)
25
ND_BIAS(+)
26
27
ND_BIAS(-)
28
IRIS_B
IRIS_XB
29
YAW(+)
30
YAW(+)
31
YAW(+)
32
YAW(-)
33
YAW(-)
34
YAW(-)
35
PITCH(+)
36
37
PITCH(+)
PITCH(+)
38
39
PITCH(-)
PITCH(-)
40
PITCH(-)
41
XX
R4013
R4014
T_TEMP_GND
42
T_TEMP_OUT
43
PITCH_HALL(-)
44
XX
PITCH_BIAS(+)
45
46
PITCH_BIAS(-)
47
PITCH_HALL(+)
YAW_BIAS(-)
48
YAW_HALL(+)
49
YAW_HALL(-)
50
XX
YAW_BIAS(+)
51
LENS
BLOCK
FP-1518
FLEXIBLE
LND001
(PAGE 6-37)
CN4004 12P
Note: LENS BLOCK is supplied as block,
so that PRINTED WIRING BOARD and
SCHEMATIC DIAGRAM are omitted.
FR_GND
1SHUTTER_XA
2SHUTTER_XA
3SHUTTER_A
4SHUTTER_A
5FR_GND
6IR_LED_ON
7SIRCS_SIG
8D_2.8V
9XTALLY_LED
10KEY_AD3
11DIAL_B
12DIAL_A
COM402
SHUTTER_XA
SHUTTER_A
FR_GND
IR_LED_ON
SIRCS_SIG
D_2.8V
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
REG_GND
A
B
C
D
62
63
61AUDIO_GND
SHOE_MIC_FL
A
HOTSHOE_ID1_CN
HOTSHOE_ID2_ADC1_IN5
B
C
D
CN4001 61P
FP-1550
FLEXIBLE
(PAGE 6-8)
SHOE_MIC_FR
AUDIO_GND
LANC_SIG
REG_GND
SHOE_UNREG
SHOE_UNREG
SHOE_UNREG
SHOE_UNREG
REG_GND
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
REG_GND
MSX_CLK
REG_GND
MSX_BIO_3
MSX_BS
SD_XSDCD
SD_DAT_1
SD_DAT_3
SD_DAT_2
REG_GND
LND002
60
59
58
57
56
55EXT_STROBE_ON
54
53
52
51
50
49
48REG_GND
47REG_GND
46
45
44XC_UNREG
43
42
41XC_UNREG
40XC_UNREG
39
38
37REG_GND
36REG_GND
35
34MT_5.0V
33MT_5.0V
32MT_5.0V
31MT_5.0V
30REG_GND
29MSX_3.3V
28MSX_3.3V
27REG_GND
26
25
24
23MSX_BIO_2
22MSX_BIO_0
21MSX_BIO_1
20REG_GND
19MSX_INS_HIZ
18
17SD_SDWP
16
15REG_GND
14REG_GND
13SD_CLK
12REG_GND
11SD_VCC
10SD_VCC
9REG_GND
8SD_CMD
7REG_GND
6
5SD_DAT_0
4
3
2REG_GND
1
REG_GND
SHOE_MIC_FR
AUDIO_GND
EXT_STROBE_ON
LANC_SIG
SHOE_MIC_FL
R4002 XX
R4003
C4003
XX
SHOE_UNREG
XC_UNREG
MT_5.0V
MSX_3.3V
MSX_CLK
MSX_BIO_3
MSX_BIO_2
MSX_BIO_0
MSX_BIO_1
MSX_INS_HIZ
MSX_BS
SD_SDWP
SD_XSDCD
SD_CLK
SD_VCC
SD_CMD
SD_DAT_1
SD_DAT_0
SD_DAT_3
SD_DAT_2
C4001
D_2.8V
8
RB4001
100k
1234567
HOTSHOE_ID1
XX
HOTSHOE_ID2
XX
IC_5601_IC_5201_CLK
XIC_5601_CPU_RST
IC_5601_P_LIMIT
IC_5601_INT_REQ
IC_5601_2_EXPOSE
LENS_COVER_DIR_PWM
LENS_TEMP_AD
XPANEL_POWER_ON
CN4002
FP-1551
FLEXIBLE
(PAGE 6-8)
E
SHOE_MIC_FR
SHOE_MIC_FL
AUDIO_GND
HOTSHOE_ID1
SHOE_XC_7V
HOTSHOE_ID2
EXT_STROBE_ON
F
LANC_SIG
XSYS_RST
REG_GND
R4001 3300
D4001
1SS357
SHOE_GND
4
5
D4002
XX
1
2
3
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
C4002
10
E
CN4005 12P
SHOE_GND
1
SHOE_MIC_FR
2
SHOE_MIC_FL
3
MIC_GND
4
HOTSHOE_ID1
5
SHOE_UNREG
6
SHOE_UNREG
7
HOTSHOE_ID2
8
EXT_STROBE_ON
9
LANC_SIG
10
NC(SHOE_CONT)
11
SHOE_GND
12
u
FP-1523
FLEXIBLE
LND001
(PAGE 6-37)
EVER_3.0V
PANEL_OPEN
XPANEL_POWER_ON
REG_GND
Q4002
SSM6N37FE,RSONYM
PANEL
OPEN/CLOSE
DETECT
2
61
4
3
5
CN4006 6P
1 EVER_3.0V
2 EVER_3.0V
3 REG_GND
4 REG_GND
5 PANEL_O/C_GMR
6 PANEL_O/C_GMR
FP-1554
FLEXIBLE
LND001
(PAGE 6-7)
LD-297 BOARD (1/5)
CONNECTORS
XX MARK: NO MOUNT
F
6-3
Page 56
12345 6 7 8 9
A
MR_A_2.8V
REG_GND
Z_MR_B
Z_MR_A
F_MR_B
F_MR_A
B
ND_BIAS+
ND_HALL+
ND_BIAS-
ND_HALL-
C
D
C5202
22u
Z_MR_B
Z_MR_A
F_MR_B
F_MR_A
ND_BIAS+
ND_HALL+
ND_BIAS-
ND_HALL-
IC_5201_PIO0
IC_5201_PIO1
IR_FILTER_EN
IR_FILTER_DIR
ND_DRIVE-
ND_DRIVE+
F_MR_A
2700
R5201
39k
0.0022u
R5202 8200
R5203
C5203
C5204
0.1u
RB5201
4700
1
2
4
3
6
5
7
IRF-
IRF+
8
F_MR_B
3
2700
R5204
C5205
0.0022u
R5206
39k
8200
R5205
E2
H8
G8
C1
G7
F4
G5
C3
H4
OPIN1P
OPIN1N
OPOUT1
DAC1OUT
OPOUT0
G4
OPIN0N
G3
DAC0OUT
A1
OPIN0P
H3
MVCC
A5
MGND
B5
PIO0
A8
PIO1
B7
PIO2
A7
PIO3
C4
OUT0A
B4
OUT0B
C5
OUT1A
A6
OUT1B
B6
TEST
D4
IR5
OPIN4P
OPIN4N
OPOUT4
DAC4OUT
IC5201
BU24130GU-E2
IRIS DRIVE,
ND DRIVE,
ZOOM DRIVE,
FOCUS DRIVE
C5207
0.1u
C5209
0.1u
F1
G1
H1
G2
E1
E3
D1
VREF
AVSS
ISEN5
OPOUT8
AVDD
CREFIN
OPIN8N
8200
R5210
IR7
OPOUT9
DAC6OUT
OPOUT5
DAC3OUT
OPOUT3
DAC2OUT
OPOUT2
H2
ISEN7
F3
C5211
E4
OPIN9N
F2
OPIN5P
E7
D3
OPIN5N
F7
F6
OPIN3P
H7
R5208
D2
OPIN3N
H6
G6
OPIN2P
H5
R5209
C2
OPIN2N
F5
E5
ND_BIASND_BIAS+
R5211
ND_HALL+
10k
0.1u
ND_HALL-
C5212
0.1u
8200
39k
R5212
C5213
0.0022u
8200
39k
R5213
C5214
0.0022u
4
VDD
VOUT
IC5202
2.8V REG
MM3404A28URE
GND
1CE2
C5215
1u
R5214
R5215
R5216
C5217
1u
R5220
XX
XX
R5218
220k
180k
C5216
R5217
0.0033u
2700
2700
R5221
C5218
XX
0.22u
3900
R5219
Z_MR_B
Z_MR_A
A_3.3V
REG_GND
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
OPOUT6F8OPIN6NE8OPIN6PD6OPOUT7D7OPIN7ND8OPIN7PD5VDB8CLKC7XCLRA3SOUTB2SINB3CSBA2SCKC8VDDIOA4DVDDC6DVSS
E6
C5208
0.1u
R5222 XX
R5207
C5206
0.1u
10k
C5210
0.1u
D_1.8V
C5220
XX
C5219
22u
10V
L5201 XX
D_2.8V
REG_GND
MT_5.0V
REG_GND
IC_5201_SCK
XCS_IC_5201
IC_5201_SO
IC_5201_SI
XIC_5201_RST
IC_5201_VD
IC_5601_IC_5201_CLK
LD-297 BOARD (2/5)
IRIS/ND/ZOOM/FOCUS DRIVE
XX MARK: NO MOUNT
E
F
6-4
Page 57
12345 6 7 8 9
IC5601
R2J30503LG
STEADYSHOT
R5628 XX
D_1.2V
R5629 XX
A
REG_GND
COM566
MT_GND_IC_5601
B
L5601
2uH
S
IC5609
TPS63060DSCR
7.0V REG
PowerPAD
L2
10
VOUT
9
FB
8
GND
7
VAUX
6
11
R5618
C5609
C5610
130k
10u
C5606
0.1u
10u
R5619
10k
XCON_7.0V_OUT
D_2.8V
22k
R5614
PGOOD_XC
XX
R5624
XC_PGND
Note: IC5602, IC5603, IC5609, IC5610, IC5611 L5601 and L5603 are not
supplied, but they are included in LD-297 COMPLETE BOARD.
1
R5613 XX
XC_PGND
XC_AGND
L1
2
IN
3
EN
4
PS/SYNC
5
PG
COM561
COM563
XC_UNREG
C5605
C5603
C5604
10u
XX
10u
XC_UNREG
R5610 XX
XIC_5201_RST
C
REG_GND
MR_A_2.8V
MT_GND_IC_5601
IC_5601_IC_5201_CLK
XSYS_RST
XIC_5601_CPU_RST
IC_5601_SCK
XCS_IC_5601
IC_5601_SO
IC_5601_SI
IC_5201_VD
IC_5601_2_EXPOSE
IC_5601_P_LIMIT
IC_5601_INT_REQ
REG_GND
MT_5.0V
REG_GND
D_2.8V
C5620
C5622
C5626
0.1u
L5602 XX
R5630 XX
R5631 XX
R5632 XX
R5633 XX
CAM_V
C5617
C5618
22u
0.1u
10V
XX
XX
C5613
C5614
PGOOD_XC
PGOOD_XC_IC_5601
PITCH_INA_O
PITCH_INB_O
YAW_INA_O
YAW_INB_O
IC_5201_PIO0
IC_5201_PIO1
IRIS_ENB
IRIS_DIR_A
IRIS_DIR_B
C5627
0.1u
0.1u
XX
CL5601
F10
E10
CL5602
CL5603
CL5604
CL5605
CL5606
CL5607
K10
J10
H10
G10
VCCD12
F2
VCCD3
F7
GNDD
F6
VCCA3
B1
GNDA3
A1
VM01
G3
VM23
J4
VM45
J7
VM6
K8
PGND0
G2
PGND1
H3
PGND2
H4
PGND3
J5
PGND4
J6
PGND5
K7
PGND6/RNF
J9
VLIM
G9
CLK
G1
RESET_N
D1
XDL
F5
SIO0_SCK
E1
SIO0_XSCS
G5
SIO0_SI
F1
SIO0_SO
G4
GPIO0
E4
GPIO1
E3
GPIO2
E2
GPIO3
D2
GPIO4
C2
GPIO5
C1
GPIO6/I2C_SCL
GPIO7/I2C_SDA
UDITRST_N
D6
DBGMOD/SEL
E5
UDITCK/SIO2_SCK
E8
UDITDI/SIO2_SI
D8
UDITDO/SIO2_SO
D7
UDITMS/SIO2_SRDY_N
E7
TEST
K1
IN2A
IN2B
IN3A
G6
IN3B
G7
IN4A
H9
IN4B
IN5A
F9
IN5B
IN6A
G8
IN6B
F8
PROCESSOR
OP_6OUT
OP_7OUT
VREF(1.4V)
OP_8OUT
OP_9AOUT
OP_9AINN
OP_9AINP/DA_9
OP_9BOUT
OP_9BINN
OP_9BINP
SIO1_SCK
SIO1_XSCS
OP_6INN
OP_6INP
OP_7INN
OP_7INP
OP_8INN
OP_8INP
SIO1_SO
XX
R5646
A4
SE_2
A3SE_3
CL5608
SE_4F
A2
B2SE_5F
B3
SE_4S
CL5609
B4
SE_5S
DF_0N
C10
DF_0P
C9
CC_0
E9
DF_1N
D10
D9
DF_1P
E6
CC_1
C5628
0.01u
DA_6
A5
R5638
A6
270k
B6
C5629
B5
0.01u
C5
DA_7
R5639
C3
270k
C4
D4
C6
R5640 XX
A10
B10
R5641 XX
B9
DA_8
A9
R5642 XX
B8
A8
R5643 XX
A7
B7
C8
R5645 XX
C7
CC_2
D5
15k
R5637
CC_R
D3
H1
K2
J2
SIO1_SI
J1
OUT0A
F3
OUT0B
F4
J3
OUT1A
H2
OUT1B
K3OUT2A
K4OUT2B
K5OUT3A
H5OUT3B
H6OUT4A
K6OUT4B
H8OUT5A
H7OUT5B
J8OUT6A
K9OUT6B
C5635
C5634
XX
XX
C5630
C5636
0.047u
0.047u
C5631
0.047u
R5644
XX
R5647 XX
0.022u
FOCUS-
FOCUS+
IRIS_XA
IRIS_A
IRIS_XB
IRIS_B
R5648 22k
R5649
C5641
C5639
C5644
0.022u
0.1u
C5643
C5642
C5640
0.047u
0.047u
0.047u
10k
R5650
22k
R5651
10k
C5645
0.1u
PITCH_AD
YAW_AD
GY_GND
PITCH_HALL+_O
PITCH_HALL-_O
PITCH_BIAS-_O
YAW_HALL+_O
YAW_HALL-_O
YAW_BIAS-_O
REG_GND
A
B
REG_GND
C
IC5605, IC5606
L5603
2uH
S
IC5610
TPS63060DSCR
XC_PGND
XC_AGND_IC2
7V REG
PowerPAD
L2
10
VOUT
FB
GND
VAUX
11
C5649
SHOE_XC_7V
9
8
7
6
R5655
C5654
C5655
0.1u
30k
R5656
10k
C5656
10u
10u
SHOE_XC_7V
C5651
10u
10u
XC_PGND
1
L1
2
IN
3
EN
4
PS/SYNC
5
PG
R5658
XX
XC_UNREG
SHOE_UNREG
D
REG_GND
XC_UNREG_IC2
XX
R5652
R5659
100k
COM565
C5648
C5646
C5647
10u
XX
XX
E
COM567
PITCH-_O
PITCH+_O
XCON_7.0V_OUT_PIT
F
PITCH-_O
XC_PGND
R5605 XX
COM568
R5603 XX
R5604 XX
78
56
B
9
A
R5601
XX
R5602
XX
IC5607 XX
C5601
12
34
XX
R5606
XX
C5602
XXR5607 XX
R5608
R5612 XX
XX
R5611
XX
PITCH-_O_OUT
YAW-_O
YAW+_OPITCH+_O_OUT
XCON_7.0V_OUT_YAW
YAW-_O
XC_PGND
COM569
R5622 XX
COM570
R5620 XX
R5623 XX
R5621 XX
78
56
9
R5615
C5607
IC5608 XX
XX
XX
12
34
R5617
XX
R5616
XX
C5611
XX
R5625
R5627 XX
XX
R5626
XX
YAW-_O_OUT
YAW+_O_OUT
PGOOD_XC
LENS_COVER_DIR_PWM
PGOOD_XC_IC_5601
PITCH_INA_O
PITCH_INB_O
REG_GND
D_2.8V
LENSV_EN
REG_GND
YAW_INA_O
YAW_INB_O
C5652
0.1u
B2
SGND
IC5611
LV8417CS-TE-L-H
LENS BARRIER DRIVE
ENA
IN1
IN2
PGND
LV8417CS-TE-L-H
PITCH DRIVE
ENA
IN1
IN2
PGND
LV8417CS-TE-L-H
YAW DRIVE
OUT2
A1
OUT1
C1
VCC
C2
VM
A2
B2
SGND
OUT2
A1
OUT1
C1
VCC
C2
VM
A2
IC5602
B2
SGND
OUT2
A1
OUT1
C1
VCC
C2
VM
A2
IC5603
ENA
C3
IN1
B3
IN2
A3
PGND
B1
C5612
0.1u
D_2.8V
COM572
R5634
R5635 XX
XX
C3
B3
A3
B1
C5616
0.1u
C3
B3
A3
B1
SHUTTER_XA
SHUTTER_A
COM564
COM571
XC_PGND
XCON_7.0V_OUT_PIT
XC_PGND
XCON_7.0V_OUT
XCON_7.0V_OUT_PIT
XC_PGND
XCON_7.0V_OUT_YAW
10u
C5653
PITCH+_O_OUT
PITCH-_O_OUT
10u
C5623
C5625 0.1u
YAW+_O_OUT
YAW-_O_OUT
C5621 10u
C5624 0.1u
REG_GND
MT_5.0V
MT_GND
COM562
C5632 10u
ZM_ENB
C5633 XX
ZM_ENB
C5637 0.1u
C5638 0.1u
MT_GND
ZOOM MOTOR DRIVE
IC5605 R2A30427BM
A1
B1
C1
IC5606 R2A30427BM
A1
B1
C1
LD-297 BOARD (3/5)
LENS CONTROL
XX MARK: NO MOUNT
OUTA
GND
VM
EN
GND
VM
EN
A2
OUTB
B2
IN
C2
OUTA
A2
OUTB
B2
IN
C2
ZOOM_XA_OUT
ZOOM_A_OUT
ZM_DIR_A
ZOOM_XB_OUT
ZOOM_B_OUT
ZM_DIR_B
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-5
Page 58
12345 6 7 8 9
A
B
YAW_AD
PITCH_AD
R7508
XX
MR_A_2.8V
C
A_2.8V_REG
C7501
0.1u
R7507
XX
OUTMODE
13141516
VregA
(NC)
VregD
SL
MISO/OUTA
MOSI/OUTB
SE7501
42.8kHz/45.4kHz
PITCH/YAW
SENSOR
9101112
SCLK
DGND
Vref/COSR
CSB
A_3.3V
3IN4
OUT
XX
IC7501
78
Vdd
6
5
REG_GND
C7511
XX
GND
1CE2
C7512
XX
A_2.8V_REG
A
B
C
D
C7502
0.1u
VCC
1234
C7503
0.1u
AGND1V1AGND2
C7504
0.1u
XX
R7509
GY_GND
GY_GND
COM751
REG_GND
E
F
LD-297 BOARD (4/5)
D
E
F
PITCH/YAW SENSOR
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-6
Page 59
12 3 4
12 3 4
A
SD_DAT_2
SD_DAT_3
SD_DAT_0
SD_DAT_1
R8041
R8024 150
R8017 XX
R8029 XX
XX
R8043
SD_CMD
SD_CLK
B
C
SD_XSDCD
SD_SDWP
SD_VCC
REG_GND
MSX_3.3V
REG_GND
MSX_BS
MSX_INS_HIZ
MSX_CLK
MSX_BIO_0
MSX_BIO_1
MSX_BIO_2
MSX_BIO_3
REG_GND
R8018
1
3
5
7
RB8002
100
XX
C8001
0.1u
1
2
3
4
5
6
7
8
RB8001
150
XXR8030
XX
C8002
0.1u
XXR8019
XXR8040
2
4
6
8
R8011
XX
CN8001 26P
(MEMORY CARD SLOT)
1 SD_DAT_2
2 MSX_BIO_4
3 SD_DAT_3
4 MSX_BIO_5
5 REG_GND(MS)
6 SD_CMD
7 MSX_BS
8 MSX_BIO_1
9 REG_GND(SD)
10 MSX_BIO_0
11 MSX_BIO_2
12 SD_VCC
13 MSX_BIO_6
14 XMSX_INS
15 SD_CLK
16 MSX_BIO_3
17 MSX_CLK
18 REG_GND(SD)
19 MSX_VCC
20 MSX_BIO_7
21 SD_DAT0
22 REG_GND(MS)
23 SD_DAT1
24 SD_INS
25 REG_GND
26 SD_WP
272829
MEMORY
STICK
PRO DUO
SD
30
D
D8001
CL-271HR-C-TS
(ACCESS)
1k
D_2.8V
XMS_ACC_LED
R8042
E
LD-297 BOARD (5/5)
F
MEMORY CARD SLOT
XX MARK: NO MOUNT
A
B
C
A
C001
0.1u
GND
VDD
3
OUT
4
B
OPEN/CLOSE
C
SE001
GMR
PANEL
DETECT
N.C.
2
1
FP-1554 FLEXIBLE BOARD
LND001 6P
1 EVER_3.0V
2 EVER_3.0V
3 REG_GND
4 REG_GND
5 PANEL_O/C_GMR
6 PANEL_O/C_GMR
LD-297
(1/5)
CN4006
(PAGE 6-3)
PANEL OPEN/CLOSE DETECT
08
12 3 4
Note:
D
22LED1_3_K
LED2_K
LED2_K
LED2_K
LED2_K
21LED1_3_K
20LED1_3_K
19
18
17VOUT_LED_A
16VOUT_LED_A
15
14
13
12
11
10
9
8
7LED2_K
6
5
4
3
2A_GND
1TH
LND72122P
A
LED1_3_K
LED1_3_K
VOUT_LED_A
VOUT_LED_A
RH-014
(4/5)
E
CN7003
(PAGE 6-24)
B
F
C
VOUT_LED_A
VOUT_LED_A
VOUT_LED_A
VOUT_LED_A
VOUT_LED_A
VOUT_LED_A
FP-1555 FLEXIBLE COMPLETE BOARD is not
supplied, but this is included in ST LED BLOCK ASSY.
D0001, D0002
(LED FLASH)
D0001
CL-773A-CW02P1-SDW-T
D0002
CL-773A-CW02P1-SDW-T
TH001
A
B
C
A
B
C
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
FP-1555 FLEXIBLE BOARD
LED FLASH
08
6-7
Page 60
12 3 4
LND001
61P
AUDIO_GND
SHOE_MIC_FL
SHOE_MIC_FR
A
B
AUDIO_GND
HOTSHOE_ID1
HOTSHOE_ID2
EXT_STROBE_ON
LANC_SIG
REG_GND
SHOE_UNREG
SHOE_UNREG
SHOE_UNREG
SHOE_UNREG
REG_GND
REG_GND
REG_GND
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
XC_UNREG
REG_GND
REG_GND
REG_GND
C
VC-658
(1/10)
CN1001
(PAGE 6-9)
D
E
REG_GND
MSX_3.3V
MSX_3.3V
REG_GND
MSX_CLK
REG_GND
MSX_BIO_3
MSX_BIO_2
MSX_BIO_0
MSX_BIO_1
REG_GND
MSX_INS_HIZ
SD_SDWP
SD_XSDCD
REG_GND
REG_GND
REG_GND
REG_GND
SD_CMD
REG_GND
SD_DAT_1
SD_DAT_0
SD_DAT_3
SD_DAT_2
REG_GND
REG_GND
MT_5.0V
MT_5.0V
MT_5.0V
MT_5.0V
MSX_BS
SD_CLK
SD_VCC
SD_VCC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
61P
LND002
AUDIO_GND
61
60
SHOE_MIC_FL
59
SHOE_MIC_FR
58
AUDIO_GND
57
HOTSHOE_ID1_CN
56
HOTSHOE_ID2_ADC1_IN5
55
EXT_STROBE_ON
54
LANC_SIG
53
REG_GND
SHOE_UNREG
52
51
SHOE_UNREG
50
SHOE_UNREG
49
SHOE_UNREG
48
REG_GND
47
REG_GND
46
REG_GND
45
XC_UNREG
44
XC_UNREG
43
XC_UNREG
42
XC_UNREG
41
XC_UNREG
40
XC_UNREG
39
XC_UNREG
38
XC_UNREG
37
REG_GND
36
REG_GND
35
REG_GND
34
MT_5.0V
33
MT_5.0V
32
MT_5.0V
31
MT_5.0V
30
REG_GND
29
MSX_3.3V
28
MSX_3.3V
27
REG_GND
26
MSX_CLK
25
REG_GND
24
MSX_BIO_3
23
MSX_BIO_2
22
MSX_BIO_0
21
MSX_BIO_1
20
REG_GND
19
MSX_INS_HIZ
18
MSX_BS
17
SD_SDWP
16
SD_XSDCD
15
REG_GND
14
REG_GND
13
SD_CLK
12
REG_GND
11
SD_VCC
10
SD_VCC
9
REG_GND
8
SD_CMD
7
REG_GND
6
SD_DAT_1
5
SD_DAT_0
4
SD_DAT_3
3
SD_DAT_2
2
REG_GND
1
REG_GND
LD-297
(1/5)
CN4001
(PAGE 6-3)
A
B
C
D
E
A
B
C
D
E
12 3 4
VC-658
(1/10)
CN1002
(PAGE 6-9)
REG_GND
IC_5601_IC_5201_CLK
REG_GND
XIC_5601_CPU_RST
XIC_5201_RST
IC_5601_P_LIMIT
IC_5601_INT_REQ
XSYS_RST
REG_GND
XCS_IC_5601
IC_5601_SI
IC_5601_SO
IC_5601_SCK
REG_GND
REG_GND
REG_GND
IC_5201_VD
REG_GND
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
IC_5601_2_EXPOSE
REG_GND
REG_GND
REG_GND
REG_GND
LENS_COVER_DIR_PWM
LENSV_EN
ZM_DIR_A
ZM_DIR_B
ZM_ENB
REG_GND
LENS_TEMP_AD
REG_GND
IR_FILTER_DIR
IR_FILTER_EN
REG_GND
IC_5201_SCK
IC_5201_SO
IC_5201_SI
XCS_IC_5201
REG_GND
REG_GND
IR_LED_ON
SIRCS_SIG
XTALLY_LED
KEY_AD3
REG_GND
PANEL_OPEN
XPANEL_POWER_ON
EVER_3.0V
XMS_ACC_LED
REG_GND
REG_GND
CAM_V
D_1.2V
D_2.8V
D_1.8V
A_3.3V
DIAL_B
DIAL_A
LND00161P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
LND002 61P
REG_GND
61
60
IC_5601_IC_5201_CLK
59
REG_GND
58
XIC_5601_CPU_RST
57
XIC_5201_RST
56
IC_5601_P_LIMIT
55
IC_5601_INT_REQ
54
XSYS_RST
REG_GND
53
52
XCS_IC_5601
51
IC_5601_SI
50
IC_5601_SO
49
IC_5601_SCK
48
REG_GND
47
REG_GND
46
REG_GND
45
CAM_V
44
IC_5201_VD
43
REG_GND
42
IRIS_DIR_A
41
IRIS_DIR_B
40
IRIS_ENB
39
IC_5601_2_EXPOSE
38
D_1.2V
37
REG_GND
36
REG_GND
35
REG_GND
34
D_2.8V
33
D_1.8V
32
REG_GND
31
LENS_COVER_DIR_PWM
30
LENSV_EN
29
ZM_DIR_A
28
ZM_DIR_B
27
ZM_ENB
26
REG_GND
25
LENS_TEMP_AD
24
REG_GND
23
IR_FILTER_DIR
22
IR_FILTER_EN
21
REG_GND
20
IC_5201_SCK
19
IC_5201_SO
18
IC_5201_SI
17
XCS_IC_5201
16
A_3.3V
15
REG_GND
14
REG_GND
13
IR_LED_ON
12
SIRCS_SIG
11
XTALLY_LED
10
KEY_AD3
9
DIAL_B
8
DIAL_A
7
REG_GND
6
PANEL_OPEN
5
XPANEL_POWER_ON
4
EVER_3.0V
3
XMS_ACC_LED
2
REG_GND
1
REG_GND
LD-297
(1/5)
CN4002
(PAGE 6-3)
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
FP-1550 FLEXIBLE BOARD
VC-LD CONNECTION
(PRINTED WIRING BOARD is omitted.)
FP-1551 FLEXIBLE BOARD
F
F
08
6-8
VC-LD CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
Page 61
12345 6 7 8 9
A
CN1001
B
FP-1550
FLEXIBLE
LND001
(PAGE 6-8)
C
61P
1AUDIO_GND
2SHOE_MIC_FL
3SHOE_MIC_FR
4AUDIO_GND
5HOTSHOE_ID1
6HOTSHOE_ID2
7EXT_STROBE_ON
8LANC_SIG
9REG_GND
10SHOE_UNREG
11SHOE_UNREG
12SHOE_UNREG
13SHOE_UNREG
14REG_GND
15REG_GND
16REG_GND
17XC_UNREG
18XC_UNREG
19XC_UNREG
20XC_UNREG
21XC_UNREG
22XC_UNREG
23XC_UNREG
24XC_UNREG
25REG_GND
26REG_GND
27REG_GND
28MT_5.0V
29MT_5.0V
30MT_5.0V
31MT_5.0V
32REG_GND
33MSX_3.3V
34MSX_3.3V
35REG_GND
36MSX_CLK
37REG_GND
38MSX_BIO_3
39MSX_BIO_2
40MSX_BIO_0
41MSX_BIO_1
42REG_GND
43MSX_INS_HIZ
44MSX_BS
45SD_SDWP
46SD_XSDCD
47REG_GND
48REG_GND
49SD_CLK
50REG_GND
51SD_VCC
52SD_VCC
53REG_GND
54SD_CMD
55REG_GND
56SD_DAT_1
57SD_DAT_0
58SD_DAT_3
59SD_DAT_2
60REG_GND
61REG_GND
62
63
SHOE_MIC_FL
SHOE_MIC_FR
AUDIO_GND
HOTSHOE_ID1
HOTSHOE_ID2
EXT_STROBE_ON
LANC_SIG
SHOE_UNREG
XC_UNREG
MT_5.0V
MSX_3.3V
MSX_CLK
MSX_BIO_3
MSX_BIO_2
MSX_BIO_0
MSX_BIO_1
MSX_INS_HIZ
MSX_BS
SD_SDWP
SD_XSDCD
SD_CLK
SD_VCC
SD_CMD
SD_DAT_1
SD_DAT_0
SD_DAT_3
SD_DAT_2
FP-1551
FLEXIBLE
LND001
(PAGE 6-8)
CN1002 61P
REG_GND
IC_5601_IC_5201_CLK
REG_GND
XIC_5601_CPU_RST
XIC_5201_RST
IC_5601_P_LIMIT
IC_5601_INT_REQ
XSYS_RST
REG_GND
XCS_IC_5601
IC_5601_SI
IC_5601_SO
IC_5601_SCK
REG_GND
REG_GND
REG_GND
CAM_V
IC_5201_VD
REG_GND
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
IC_5601_2_EXPOSE
D_1.2V
REG_GND
REG_GND
REG_GND
D_2.8V
D_1.8V
REG_GND
LENS_COVER_DIR_PWM
LENSV_EN
ZM_DIR_A
ZM_DIR_B
ZM_ENB
REG_GND
LENS_TEMP_AD
REG_GND
IR_FILTER_DIR
IR_FILTER_EN
REG_GND
IC_5201_SCK
IC_5201_SO
IC_5201_SI
XCS_IC_5201
A_3.3V
REG_GND
REG_GND
IR_LED_ON
SIRCS_SIG
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
REG_GND
PANEL_OPEN
XPANEL_POWER_ON
EVER_3.0V
XMS_ACC_LED
REG_GND
REG_GND
A
B
C
FP-1522
FLEXIBLE
LND001
(PAGE 6-37)
CN1003 61P
J_5.0V
1J_5.0V
2J_5.0V
3
4J_5.0V
5J_5.0V_GND
6J_5.0V_GND
7J_5.0V_GND
8J_5.0V_GND
9D_1.8V
10XSTRB_FULL
11STROBE_ON
12I2C_SCK
13I2C_SDA
14XCS_EVF
15AV_SCK
16AV_SO
17REG_GND
18LCD_B_7
19LCD_B_6
20LCD_B_5
21LCD_B_4
22LCD_B_3
23LCD_B_2
24LCD_B_1
25LCD_B_0
26REG_GND
27XPANEL_EVF_PS
28LCD_XVD
29LCD_XHD
30REG_GND
31EVF_CLK_OUT
32REG_GND
33XBB_RST
34XEVF_SW
35EVER_3.0V
36MIC_PWR_ON
37MIC_JACK_IN
38HP_JACK_IN
39AUDIO_GND
40SHOE_MIC_FL
41SHOE_MIC_FR
42AUDIO_GND
43BATT_LI_3V
44A_2.8V
45REG_GND
46SDO
47SDI1_MAG
48SDI0_SPDIF_IN_MAG
49MCK_CN
50LRCK_OUT
51BCK_CN
52XCS_IC_2801
53XSYS_RST
54LANC_DC
55JACK_AD
56LANC_SIG
57FR_XRESET
58REG_GND
59DAC_IOUT_PB
60DAC_IOUT_Y
61REG_GND
J_5.0V
VD1004
J_5.0V_GND
COM102
REG_GND
CM-121
CN6701
(PAGE 6-2)
Through the FP-1520
Flexible Board
MCK_CN
BCK_CN
VD1005
REG_GND
J_5.0V_GND
D_1.8V
XSTRB_FULL
STROBE_ON
I2C_SCK
I2C_SDA
XCS_EVF
AV_SCK
AV_SO
RB1002
LCD_B_7
220
1
2
LCD_B_6
4
3
6
5
LCD_B_5
7
8
LCD_B_4
RB1001
LCD_B_3
220
1
2
LCD_B_2
4
3
6
5
LCD_B_1
7
8
LCD_B_0
XPANEL_EVF_PS
LCD_XVD
LCD_XHD
EVF_CLK_OUT
XBB_RST
XEVF_SW
EVER_3.0V
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
SHOE_MIC_FL
SHOE_MIC_FR
AUDIO_GND
BATT_LI_3V
A_2.8V
SDO
SDI1_MAG
SDI0_SPDIF_IN_MAG
LRCK_OUT
XCS_IC_2801
XSYS_RST
LANC_DC
JACK_AD
LANC_SIG
FR_XRESET
DAC_IOUT_PB
DAC_IOUT_Y
REG_GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
63
IC_5601_IC_5201_CLK
XIC_5601_CPU_RST
XIC_5201_RST
IC_5601_P_LIMIT
IC_5601_INT_REQ
XSYS_RST
XCS_IC_5601
IC_5601_SI
IC_5601_SO
IC_5601_SCK
CAM_V
IC_5201_VD
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
IC_5601_2_EXPOSE
D_1.2V
D_2.8V
D_1.8V
LENS_COVER_DIR_PWM
LENSV_EN
ZM_DIR_A
ZM_DIR_B
ZM_ENB
LENS_TEMP_AD
IR_FILTER_DIR
IR_FILTER_EN
IC_5201_SCK
IC_5201_SO
IC_5201_SI
XCS_IC_5201
A_3.3V
IR_LED_ON
SIRCS_SIG
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
PANEL_OPEN
XPANEL_POWER_ON
EVER_3.0V
XMS_ACC_LED
62
REG_GND
CN1004 51P
SUBL_DINP5
CN1006
R1006
XX
51D_1.8V
50AVDD18_SUBL
49A_3.3V
48REG_GND
47REG_GND
46SUBL_DINP1
45SUBL_DINN1
44REG_GND
43SUBL_DINP2
42SUBL_DINN2
41REG_GND
40SUBL_DINP3
39SUBL_DINN3
38REG_GND
37SUBL_DINP4
36SUBL_DINN4
35REG_GND
34
33SUBL_DINN5
32REG_GND
31SUBL_CLKINP
30SUBL_CLKINN
29REG_GND
28SUBL_DINP6
27SUBL_DINN6
26REG_GND
25SUBL_DINP7
24SUBL_DINN7
23REG_GND
22SUBL_DINP8
21SUBL_DINN8
20REG_GND
19SUBL_DINP9
18SUBL_DINN9
17REG_GND
16SUBL_DINP10
15SUBL_DINN10
14REG_GND
13REG_GND
12SENS_VD
11SENS_HD
10SENSSO
9SENSXCS
8SENSSI
7REG_GND
6SENSSCK
5REG_GND
4XFLASH_RST
3REG_GND
2CLK_CMOS_IN
1REG_GND
D_1.8V
AVDD18_SUBL
A_3.3V
REG_GND
REG_GND
SUBL_DINP1
SUBL_DINN1
REG_GND
SUBL_DINP2
SUBL_DINN2
REG_GND
SUBL_DINP3
SUBL_DINN3
REG_GND
SUBL_DINP4
SUBL_DINN4
REG_GND
SUBL_DINP5
SUBL_DINN5
REG_GND
SUBL_CLKINP
SUBL_CLKINN
REG_GND
SUBL_DINP6
SUBL_DINN6
REG_GND
SUBL_DINP7
SUBL_DINN7
REG_GND
SUBL_DINP8
SUBL_DINN8
REG_GND
SUBL_DINP9
SUBL_DINN9
REG_GND
SUBL_DINP10
SUBL_DINN10
REG_GND
REG_GND
SENS_VD
SENS_HD
SENSSO
SENSXCS
SENSSI
REG_GND
SENSSCK
REG_GND
XFLASH_RST
REG_GND
CLK_CMOS_IN_IMG
REG_GND
XGPS_RST
PANEL_NOR/REV
XPJ_RESET
REG_GND
I2C_SDA
D0-
D0+
CLK-
CLK+
D1-
D1+
D2-
D2+
SP_R-
SP_R+
VD1003
33P
_GND
1REG
2REG_GND
3D0-
4 @CirP
5D0+
6REG_GND
7CLK-
8 @CirP
9CLK+
10 REG_GND
11 REG_GND
12 REG_GND
13 D1-
14 @CirP
15 D1+
16 REG_GND
17 D2-
18 @CirP
19 D2+
20 REG_GND
21 REG_GND
22 SP_R-
23 SP_R+
24 REG_GND
25 REG_GND
26 D_2.8V
XGPS_RST
27
28 REG_GND
29 REG_GND
30 PANEL_NOR/REV
31 I2C_SDA
XPJ_RESET
32
33 REG_GND
FP-1519
FLEXIBLE
LND001
(PAGE 6-35)
PJ_PWR_EN
GPS_UART_RXD
GPS_UART_TXD
TP_SEL1
GPS_UART_CTS
GPS_UART_RTS
XPJ_PARK
XCS_LCD
PJ_TEMP_AD
XBB_RST
REG_GND
I2C_SCK
MT_5.0V
D_3.3V
BL_H
BL_L
TP_Y
TP_X
AV_SO
D_1.8V
AV_SCKD_2.8V
SP_L+
SP_L-
COM101
CN1005 33P
1REG_GND
2REG_GND
3I2C_SCK
4 PJ_PWR_EN
5REG_GND
6D_3.3V
7 GPS_UART_RXD
8 GPS_UART_TXD
9REG_GND
10 REG_GND
11 REG_GND
12 MT/A_5.0V
13 MT/A_5.0V
14 MT/A_5.0V
15 TP_SEL1
16 GPS_UART_CTS
17 GPS_UART_RTS
18 BL_H
19 BL_L
20 TP_Y
21 TP_X
22 XPJ_PARK
23 XCS_LCD
24
AV_SO
25 D_1.8V
26 AV_SCK
27
PJ_TEMP_AD
28 XBB_RST
29 REG_GND
30 SP_L+
31 SP_L-
32 @CirP
33 @CirP
FP-1519
FLEXIBLE
LND002
(PAGE 6-35)
D
J901
CN100720P
1
REG_GND
2
KEY_AD1
3SS
4ZOOM_VR_AD
5REG_GND
6XCHARGE_LED
7EVER_3.0V
8REG_GND
9XPHOTO_LED
10XCAM_LED
11D_2.8V
12
REG_GND
13KEY_AD2
14XPOWER_TACT_SW
15
REG_GND
16ROLL_AD
17
REG_GND
18VST_C_CHARGE
19A_2.8V
E
CPC
(FOR CHECK)
FP-1521
FLEXIBLE
LND001
(PAGE 6-27)
20REG_GND
CN10106P
1REG_GND
2DEBUG_UART0_TXD
3DEBUG_UART0_RXD
4BOOT_MODE_1
5D_2.8V
6N.C.
REG_GND
DEBUG_UART0_TXD
DEBUG_UART0_RXD
BOOT_MODE_1
D_2.8V
KEY_AD1
SS
ZOOM_VR_AD
XCHARGE_LED
EVER_3.0V
XPHOTO_LED
XCAM_LED
D_2.8V
KEY_AD2
XPOWER_TACT_SW
ROLL_AD
VST_C_CHARGE
A_2.8V
REG_GND
FP-1557
FLEXIBLE
LND004
(PAGE 6-14)
CN100818P
1D_3.3V
2D_3.3V
3MMC_PWR_ON1
4MMC_VCC
5REG_GND
6MMC_CMD
7REG_GND
8MMC_CLK
9REG_GND
10MMC_DAT_3
11MMC_DAT_4
12MMC_DAT_0
13MMC_DAT_5
14MMC_DAT_1
15MMC_DAT_6
16MMC_DAT_2
17MMC_DAT_7
18REG_GND
D_2.8V
R1001
XX
GENERAL_AD
R1002
10k
REG_GND
D_3.3V
MMC_PWR_ON1
MMC_VCC
MMC_CMD
MMC_CLK
MMC_DAT_3
MMC_DAT_4
MMC_DAT_0
MMC_DAT_5
MMC_DAT_1
MMC_DAT_6
MMC_DAT_2
MMC_DAT_7
REG_GND
DC JACK
BATTERY
TERMINAL
CN1011 6P
DC IN
Note: J901 is not included in VC-658
COMPLETE BOARD (SERVICE).
C1001
0.001u
1ACV_GND
2ACV_UNREG_CN
3BATT/XEXT_CN
4BATT_UNREG_CN
5BATT_SIG_CN
R1004
6BATT_GND
R1003
VD1001
R1005
C1002
XX
0.001u
D1001
1k
RKZ12B2KJR1
220
REG_GND
ACV_UNREG_CN
BATT/XEXT_CN
BATT_UNREG_CN
BATT_SIG
REG_GND
HDMI
F
CN1009
212220
23
CHASSIS GND
HDMI_TX2SOP
HDMI_TX2SON
REG_GND
HDMI_TX1SOP
HDMI_TX1SON
REG_GND
HDMI_TX0SOP
HDMI_TX0SON
REG_GND
HDMI_TXCP
HDMI_TXCN
REG_GND
HDMI_5V
1REG_GND
2
3
4
5
6
7
8
9
10
11
12
13
14CEC
SCL
15
SDA
16
N.C.
17
18
HPD
19
VD1002
XX
HDMI_TX2SOP
HDMI_TX2SON
REG_GND
HDMI_TX1SOP
HDMI_TX1SON
REG_GND
HDMI_TX0SOP
HDMI_TX0SON
REG_GND
HDMI_TXCP
HDMI_TXCN
REG_GND
CEC
SCL
SDA
HDMI_5V
HPD
C1003
27p
REG_GND
VC-658 BOARD (1/10)
CONNECTORS
XX MARK: NO MOUNT
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-9
Page 62
12345 6 7 8 9
D_1.8V
A
A_2.8V
B
A_2.8V_IC_1301
D_2.8V_IC_1301
D_2.8V_IC_1301
COM134
COM131
COM133
REG_GND
REG_GND
REG_GND
C
A_1.125V
REG_GND
COM137
COM138
COM139
A_1.8V
C1301
2.2u
A_1.125V_SENSE
AVDD18_SUBL
D
D_1.8V_IC_1301
REG_GND
E
REG_GND
A_3.3V
REG_GND
D_3.3V
REG_GND
F
D_1.8V_IC_1301
D_2.8V_IC_1301D_2.8V
A_2.8V_IC_1301
IC1301 (1/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
A20
C1305
0.1u
AVDD_PI
B20
AVSS_PI
A19
IOVDD_PI
C13
VSS
HDMI PROCESS
PIsensor
DEVICE_SYNC
A14
C1306
1u
IOVDD_MERGE1
B13
VSS
BEAR/ETC
V29
AVDD11_SUBL
W29
AVDD11_SUBL
Y29
AVDD11_SUBL
AB31
AVDD11_SUBL
AB30
AVDD11_SUBL
L29
AVDD18_SUBL
K29
AVDD18_SUBL
J29
AVDD18_SUBL
H31
AVDD18_SUBL
H30
AVDD18_SUBL
M29
C1304
C1310
C1302
0.1u
2.2u
C1307
0.1u
VSS
0.1u
N29
VSS
P29
R29
T29
U29
AC31
Y26
VSS
VSS
VSS
VSS
IOVDD_CMOSSIO
VSS
subLVDS
CMOS I/O
AD31
IOVDD_CLKCMOS
AD29
VSS
CMOS CLK IN
AK17
AVDD33_USB
AL17
AVDD33_USB
AJ19
C1303
10u
C1309
0.1u
AVSS33_USB
C1308
0.1u
AK19
AVSS33_USB
AL19
AVSS33_USB
AF17
AVSS33C_USB
AF16
IOVDD_USBPERI
AJ17
VSS
AE17
VSS
USB
USB PERI
IC_5201_VD
MSHUT_EN
STRB_ON2_MSHUT_EN2
STRB_ON3_MSHUT_EN3
BRK2A_EN2
BRK1A_EN1
BRK0A_EN0
IRIS0_IC_5601_2_P_LIMIT
AS_PWM1A
AS_PWM1B
AS_PWM0A
AS_PWM0B
SUBL_DINP11
SUBL_DINN11
SUBL_DINP10
SUBL_DINN10
SUBL_DINP9
SUBL_DINN9
SUBL_DINP8
SUBL_DINN8
SUBL_DINP7
SUBL_DINN7
SUBL_DINP6
SUBL_DINN6
SUBL_DINP5
SUBL_DINN5
SUBL_DINP4
SUBL_DINN4
SUBL_DINP3
SUBL_DINN3
SUBL_DINP2
SUBL_DINN2
SUBL_DINP1
SUBL_DINN1
SUBL_DINP0
SUBL_DINN0
SUBL_CLKINP
SUBL_CLKINN
CIS_SHT_RST
CLK_CMOS_IN
USB_TXRTUNE
USB_ANALOGTEST
VBUS_UNLIMIT
USB_ID_EXT
USB_CHG_EN
USB_CHG_HL
USB_PWR_EN
USB_ACV_DET
STRB_ON1
SENS1A
SENS1B
ND_DIR_A
ND_DIR_B
SENS_VD
SENS_HD
SENSSCK
SENSSO
SENSXCS
USB_VBUS
USB_DP
USB_DM
USB_XO
VBUS_EN
SENS2
C19
SENS0
B19
FG1A
F19
FG1B
C20
SYS_V
AD18
CAM_V
AD17
AB17
G19
F18
G18
H19
DIR2A
C17
DIR2B
C18
A15
BRK2B
B15
DIR1A
C15
DIR1B
C16
B14
BRK1B
C14
DIR0A
F16
DIR0B
F17
G14
BRK0B
F14
F15
G15
H18
H17
ND_EN
G17
B16
IRIS1
A16
H16
G16
H14
H15
AA31
AA30
Y31
Y30
W31
W30
V31
V30
U31
U30
T31
T30
P31
P30
N31
N30
M31
M30
L31
L30
K31
K30
J31
J30
R31
R30
AC30
AC29
AB29
U26
SENSSI
AA29
V26
W26
AD30
AJ18
AJ20
USB_ID
AF18
AL18
AK18
AE18
USB_XI
AE19
AF19
AE21
AD19
AD20
AD21
AF20
AF21
AE20
Note: IC1301 is not supplied, but this is included
in VC-658 COMPLETE BOARD (SERVICE).
FB1303
R1315
180
R1313 75
DIAL_A
DIAL_B
CAM_V
IC_5201_VD
EXT_STROBE_ON
XPJ_PARK
STROBE_ON
IRIS_DIR_A
IRIS_DIR_B
IRIS_ENB
ZM_DIR_A
ZM_DIR_B
ZM_ENB
IR_FILTER_DIR
MIC_PWR_ON
REG_GND
IC_5601_P_LIMIT
SHOE_ON
MIC_JACK_IN
REG_GND
REG_GND
SUBL_DINP10
SUBL_DINN10
SUBL_DINP9
SUBL_DINN9
SUBL_DINP8
SUBL_DINN8
SUBL_DINP7
SUBL_DINN7
SUBL_DINP6
SUBL_DINN6
SUBL_DINP5
SUBL_DINN5
SUBL_DINP4
SUBL_DINN4
SUBL_DINP3
SUBL_DINN3
SUBL_DINP2
SUBL_DINN2
SUBL_DINP1
SUBL_DINN1
REG_GND
SUBL_CLKINP
SUBL_CLKINN
SENS_VD
SENS_HD
SENSSCK
SENSSO
SENSSI
SENSXCS
CLK_CMOS_IN
REG_GND
USB_VBUS
USB_ID
USB_DP
USB_DM
REG_GND
VBUS_EN
VBUS_UNLIMIT
USB_ID2
PANEL_OPEN
REG_GND
HP_JACK_IN
D_1.8V_IC_1301
REG_GND
A_1.125V
REG_GND
D_2.8V_IC_1301
REG_GND
REG_GND
REG_GND
D_2.8V_IC_1301
D_2.8V_IC_1301
REG_GND
A_1.125V
A_2.8V
A_1.8V
REG_GND
IC1301 (2/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
HDMI PROCESS
FB1302
CLK_SYS_IN
270
C1326XXR1331
R1350
68
R1351
68
LF1301
2
3
1
4
LF1302
2
3
1
4
LF1303
2
3
1
4
LF1304
2
3
1
4
8
27k
4700
RB1302
1234567
R1332
R1333
R1334 100
R1335 1k
C1324
220p
C1327
2.2u
C1325
0.1u
1
4
Q1301
FK3303010L
VST_C_CHARGE
LENS_COVER_DIR_PWM
XBUSY_HS0_MAGIC
XCS_MAGIC
XINT_HS1_MAGIC
REG_GND
SD_PWR_ON
LENSV_EN
IC_5601_INT_REQ
XBB_RST
XIC_5201_RST
IR_LED_ON
XX
XGPS_RST
IC_5601_IC_5201_CLK
XRESET_REQ
XSYS_RST
BOOT_MODE_1
CLK_SYS_IN
2
6
3
SSM6N37FE,RSONYM
5
DAC_IOUT_PB
DAC_IOUT_Y
REG_GND
HDMI_TX2SOP
HDMI_TX2SON
HDMI_TX1SOP
HDMI_TX1SON
HDMI_TX0SOP
HDMI_TX0SON
HDMI_TXCP
HDMI_TXCN
REG_GND
D_2.8V_IC_1301
HDMI_5V
R1343
R1342
1800
1800
D1304
D1303
1SS413(TPL3)
1SS413(TPL3)
Q1302
REG_GND
SDA
SCL
Q1301,Q1302
LEVEL SHIFT
CEC
CLK_CMOS_IN_GEN
FB1301
X1302
60MHz
75
R1348
VC-658 BOARD (2/10)
CPU, AV SIGNAL PROCESS, LENS CONTROL,
MODE CONTROL, HDMI PROCESS (1/3)
XX MARK: NO MOUNT
CLK_CMOS_IN_IMG
IC1302
AK8153AU-L
1
12M
2
SEL
3
ICLK
VDD
GND
REF
CLK_SYS_IN
CLK_CMOS_IN
CLK_CMOS_IN_GEN
6
5
4
FB1304
A_1.8V
C1332 10u
C1331 0.1u
C1323
10uH
L1301
C1316
0.1u
C1317
0.1u
C1313
C1314
10u
10u
AL21
AVDD_DAC_0
AK23
AVDD_DAC_1
AL23
AVDD_DAC_2
AK21
AVSS_DAC_0
AJ21
AVSS_DAC_1
AJ23
AVSS_DAC_2
AL25
DVDD_DAC_0
AK25
DVSS_DAC_0
IOVDD_AUMIC
M1
L1
Digital MIC
VSS
AL16
AVDD18_HDMI
AK16
AVDD_HDMI
AL9
C1320
C1322
0.1u
AVDD_HDMI
0.1u
AK9
AVDD_HDMI
AJ9
AVDD_HDMI
AL15
AVSS_HDMI
AK15
AVSS_HDMI
AJ15
AVSS_HDMI
AJ14
AVSS_HDMI
AL10
AVSS_HDMI
AK10
AVSS_HDMI
AJ11
AVSS_HDMI
VDAC
HDMI
DAC_IOUTP_A_Pr
DAC_IOUTN_A_Pr
DAC_IOUTP_B_Pb
DAC_IOUTN_B_Pb
DAC_IOUTP_C_Y
DAC_IOUTN_C_Y
DAC_VREF
DAC_IREF
DAC_VBP
DIG_MIC_CLK
HDMI_TX2SOP
HDMI_TX2SON
HDMI_TX1SOP
HDMI_TX1SON
HDMI_TX0SOP
HDMI_TX0SON
HDMI_TXCP
HDMI_TXCN
HDMI_CKREFP
HDMI_CKREFN
HDMI_REXT
HDMI_SDA
HDMI_SCL
0.1u
AJ22
AK22
AL22
AJ24
AK24
AL24
AJ25
AK26
AL26
M6
SDI3
M2
SDI2
M3
AL11
AK11
AL12
AK12
AL13
AK13
AL14
AK14
AJ12
AJ13
R1321 6800
AJ10
AF13
AF14
HDMI LINK or CEC
C1318
0.1u
C1315
0.1u
AJ16
IOVDD_HMI2C
AH1
IOVDD_MERGE2
AJ1
VSS
TPU
FRC_RTG
SYSTEM
AF1
IOVDD_CLK_SYS
VSS
AVDD_PLL0
AVDD_PLL1
AVDD_PLL1
AVDD_PLL2
AVDD_PLL2
AVSS_PLL0
AVSS_PLL1
AVSS_PLL1
AVSS_PLL2
AVSS_PLL2
SYS CLK
AE3
AF31
AF30
AF29
C1319
2.2u
AF26
AF25
AE31
C1321
0.1u
AE30
AE29
AE26
AE25
CEC_INOUT
AF15
TPU5_OUT
AJ8
TPU4_OUT
AK7
TPU3_OUT
AL7
TPU2_OUT
AJ6
TPU1_INA_OUT
AK6
TPU1_INB
AL6
TPU0_INA_OUT
AJ7
TPU0_INB
AF9
FRC_RTG_IN1
AF10
FRC_RTG_IN0
AD10
FRC_RTG_OUT3
AA10
FRC_RTG_OUT2
AB10
FRC_RTG_OUT1
AE10
FRC_RTG_OUT0
AE9
EXTIN_CLK2
AD15
EXTIN_CLK1
AD16
EXTIN_CLK0
AE16
EXTOUT_CLK1
AA13
EXTOUT_CLK0
AB13
IC_5601_IC_5201_CLK
AB18
BYPASS_PLL_1
AD14
BYPASS_PLL_0
AA14
PLL_MODE_0
AB15
DDRCKSEL
AA15
PLL3_FREQ_SEL
AB14
XRESET_REQ
AH3
XRESET
AH2
TEST_MODE
AF3
DEBUG_MODE_2
AB12
DEBUG_MODE_1
AD12
CL1306
DEBUG_MODE_0
AE12
CL1307
BOOT_MODE_2
AA16
BOOT_MODE_1
AB16
CL1308
BOOT_MODE_0
AA17
CLK_SYS_IN
AF2
AVDD_PLL3
AD1
AVDD_PLL4
AD2
AVSS_PLL3
AE1
AVSS_PLL4
PLL
AE2
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-10
Page 63
12345 6 7 8 9
Note: IC1301 is not supplied, but this is included
in VC-658 COMPLETE BOARD (SERVICE).
A
IC1301 (3/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
D_2.8V_IC_1301
REG_GND
B
D_2.8V_IC_1301
REG_GND
D_2.8V_IC_1301
REG_GND
A9
B9
D3
D4
AG1
AJ2
AL5
AJ3
IOVDD_MERGE1
IOVDD_MERGE1
VSS
VSS
IOVDD_I2C
VSS
IOVDD_MERGE2
VSS
C
D_2.8V_IC_1301
REG_GND
D_3.3V
REG_GND
D
SD_VCC
REG_GND
MMC_VCC
REG_GND
REG_GND
C1410
0.1u
C1411
0.1u
C1412
0.1u
C1413
0.1u
G1
IOVDD_AU
F3
VSS
A21
IOVDD_MS
A26
VSS
A24
IOVDD_TE0
B26
VSS
A18
IOVDD_TE1
B18
IOVDD_TE2
E
A3
AVDDC_SATA
C3
AVDDC_SATA
B3
AVDDC_SATA
C4
PVDD_SATA
B2
AVDD18_SATA
C2
VTERM0_SATA
REG_GND
A4
AVSSC_SATA
B4
AVSSC_SATA
C5
AVSSC_SATA
C6
AVSSC_SATA
C8
AVSSC_SATA
B8
AVSSC_SATA
A8
AVSSC_SATA
HDMI PROCESS
SIRCS
JTAG
SIO
SA Debug
DIGITAL
AUDIO I/F
MSX
SD
MMC
TE2
UART
I2C
SATA
UART2_TXD
UART2_CTS
UART0_TXD
SIO4_SCK
SIO3_SCK
SIO3_TXD
SIO2_TXD
SIO2_RXD
SIO1_SCK
SIO1_TXD
SIO1_RXD
SIO0_SCS
MSX_CLK
MSX_BIO_7
MSX_BIO_5
MSX_BIO_2
MSX_BIO_1
MSX_BIO_0
MSX_INS_HIZ
TE0_DAT_3
TE0_DAT_2
TE0_DAT_0
TE0_XSDCD
TE1_DAT_7
TE1_DAT_4
TE1_DAT_3
TE1_DAT_2
TE1_DAT_1
TE1_CMD
TE2_DAT_7
TE2_DAT_6
TE2_DAT_5
TE2_DAT_4
TE2_CMD
SATA_RX0SIP
SATA_RX0SIN
SATA_TX0SON
SATA_CKREFP
SIR_RXD
I2C_SDA
SA_TDO
TE0_CLK
TE2_CLK
G6
F6UART2_RXD
H8
H7UART2_RTS
G7UART1_TXD
F7UART1_RXD
G8
F8UART0_RXD
AD9
CL1402
AA11TDI
CL1403
AF12TCK
CL1404
AD11
TMS
CL1405
AF11TDO
CL1406
AE11
RTCK
CL1407
AB11
nTRST
AG3I2C_SCK
AG2
AF6
AE8SIO4_SCS
AC6SIO4_TXD
CL1409
AJ5SIO4_RXD
AD6
AK2SIO3_SCS
AC8
AE7SIO3_RXD
AK5SIO2_SCK
AC7SIO2_SCS
AJ4
AK4
AF8
AF7SIO1_SCS
AD8
AD7
AL3SIO0_SCK
AK3
AE6SIO0_TXD
AL4SIO0_RXD
AE13SA_TDI
AD13
H1LRCK_OUT
J2BCK_OUT
J1MCK_INOUT
G2
SDI1
H2SDI0_SPDIF_IN
G3SDO
H3SPDIF_OUT
A23MSX_BS
R1449
A22
F22
F21MSX_BIO_6
B23
C23MSX_BIO_4
B22MSX_BIO_3
C22
B21
C21
F23
FB1401
A25
B25TE0_CMD
G23
F24
C25TE0_DAT_1
C26
B24
C24TE0_SDWP
L15
K15TE1_DAT_6
L16TE1_DAT_5
K16
L17
K17
L18
K18TE1_DAT_0
L19
FB1402
K19TE1_CLK
L20
K20
K21
F20
H20TE2_DAT_3
G20TE2_DAT_2
H21TE2_DAT_1
G21TE2_DAT_0
H22
G22
A5
B5
A7SATA_TX0SOP
B7
A6
B6SATA_CKREFN
C7SATA_AMOUT
FB1406
FB1405
FB1403
XX
D1401
RB520CS-30FJT2R
D1402
RB520CS-30FJT2R
R1409
R1410 100
R1411 150
R1412
RB1403
1
3
5
7
RB1404
1
3
5
7
RB1405
1
3
5
7
R1413 100
R1414
R1472
4700
100
RB1402
100
1
2
4
3
6
5
7
8
150
150
2
4
6
8
100
2
4
6
8
100
2
4
6
8
100
GPS_UART_TXD
GPS_UART_RXD
GPS_UART_CTS
GPS_UART_RTS
IC_5601_2_EXPOSE
PJ_PWR_EN
DEBUG_UART0_TXD
DEBUG_UART0_RXD
SIRCS_SIG
D_2.8V_IC_1301
R1473
4700
I2C_SCK
I2C_SDA
XSYSAD_SEL_2
XPANEL_EVF_PS_IC_1301
FR_SCK
XCS_FRONT
FR_SO
FR_SI
MISO_SDA
IC_5201_SCK
XCS_IC_5201
IC_5201_SO
IC_5201_SI
IC_5601_SCK
XCS_IC_5601
IC_5601_SO
IC_5601_SI
XTALLY_LED
LRCK_OUT
BCK_OUT
MCK_INOUT
SDI1_IC_1301
SDI0_SPDIF_IN_IC_1301
SDO
MSX_BS
MSX_CLK
MSX_BIO_3
MSX_BIO_2
MSX_BIO_1
MSX_BIO_0
MSX_INS_HIZ
SD_CLK
SD_CMD
SD_DAT_3
SD_DAT_2
SD_DAT_1
SD_DAT_0
SD_XSDCD
SD_SDWP
MMC_DAT_7
MMC_DAT_6
MMC_DAT_5
MMC_DAT_4
MMC_DAT_3
MMC_DAT_2
MMC_DAT_1
MMC_DAT_0
MMC_CMD
MMC_CLK
REG_GND
REG_GND
AV_SCK
XCS_LCD
C1442
18p
AV_SO
C1443
C1444
18p
18p
REG_GND
D_2.8V
XX
RB1407
1
SYSAD_SEL_1
XSYSAD_SEL_2
2
Q1407
XX
3
F
REG_GND
A_2.8V_IC_1301
REG_GND
A_2.8V_IC_1301
REG_GND
A_2.8V_IC_1301
REG_GND
REG_GND
D_1.8V_IC_1301
D_2.8V_IC_1301
REG_GND
REG_GND
D_2.8V_IC_1301
REG_GND
REG_GND
1234567
4
8
3
Q1408
1
256
F1401
XX
R1469 XX
C1421
0.1u
C1423
0.1u
C1424
0.1u
C1428
0.1u
XX
SYSTEM_AD
0
R1471
HDMI_JACK_IN
D31
E30
A10
L10
B10
L11
AB1
G31
G30
G29
A13
F13
D_2.8V
REG_GND
P3
R8
N3
R7
P1
R6
P2
R3
Y1
IOVDD_BEEP
IOVSS_BEEP
AVDD33_ADC0
AVSS33_ADC0
AVDD33_ADC1
AVSS33_ADC1
IOVDD_LCD_R
VSS
IOVDD_LCD_G
VSS
IOVDD_LCD_B
VSS
IOVDD_MERGE1
VSS
IOVDD_CLKPNL
VSS
IOVDD_MERGE1
VSS
VSS
IOVDD_GPIOE
VSS
IC1301 (4/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
HDMI PROCESS
SYSTEM SOUND
CPUADC0
CPUADC1
LCD_R/ETM
LCD_G
LCD_B
LCD SYNC
CABC PWM
PANEL CLK
GPIO
GPIO_E
4
5
3
D30BEEP_PWM_P
C31BEEP_PWM_N
G12ADC0_IN11
G11ADC0_IN10
F12ADC0_IN9
F11ADC0_IN8
F10ADC0_IN7
F9ADC0_IN6
C9ADC0_IN5
C10ADC0_IN4
C12ADC0_IN3
C11ADC0_IN2
B11ADC0_IN1
A11ADC0_IN0
L13ADC1_IN11
L12ADC1_IN10
K13ADC1_IN9
K12ADC1_IN8
K11ADC1_IN7
K10ADC1_IN6
H12ADC1_IN5
H11ADC1_IN4
H10ADC1_IN3
H9ADC1_IN2
G10ADC1_IN1
G9ADC1_IN0
N8LCD_R_7
P8LCD_R_6
N7LCD_R_5
P7LCD_R_4
N6LCD_R_3
P6LCD_R_2
U8LCD_R_1
U7LCD_R_0
V8LCD_G_7
V7LCD_G_6
W8LCD_G_5
Y8LCD_G_4
W7LCD_G_3
Y7LCD_G_2
W6LCD_G_1
Y6LCD_G_0
U6LCD_B_7
V6LCD_B_6
W3LCD_B_5
V3LCD_B_4
U3LCD_B_3
U2LCD_B_2
LCD_B_1
V2
V1LCD_B_0
LCD_DATEN
Y3
FB1404
U1LCD_CLK
R1422 XX
W1LCD_XHD
R1423
XX
W2LCD_XVD
CL1408
Y10LCD_CABC_PWM
Y2EXT_PNL_CLK
K26GPIO_S__16
GPIO_S__15
L24
L25GPIO_S__14
L26GPIO_S__13
GPIO_S__12
M24
M25GPIO_S__11
M26GPIO_S__10
GPIO_S__9
N24
N25GPIO_S__8
N26GPIO_S__7
P24GPIO_S__6
P25GPIO_S__5
P26GPIO_S__4
GPIO_S__3
R24
R25GPIO_S__2
GPIO_S__1
R26
GPIO_S__0
T26
T24GPIO_SB__6
T25GPIO_SB__5
U24GPIO_SB__4
U25GPIO_SB__3
GPIO_SB__2
V24
GPIO_SB__1
V25
W25GPIO_SB__0
K14GPIO_EB__0
L14GPIO_E__0
Q1403
DMG964030R
6
LEVEL SHIFT
2
1
HPD
BEEP_PWM_P_A
ROLL_AD
C1438
0.1u
REG_GND
LENS_TEMP_AD
ZOOM_VR_AD
JACK_AD
C1441
HOTSHOE_ID2
XX
HOTSHOE_ID1
KEY_AD3
KEY_AD2
KEY_AD1
LCD_R_7
LCD_R_6
LCD_R_5
LCD_R_4
LCD_R_3
LCD_R_2
LCD_R_1
LCD_R_0
LCD_G_7
LCD_G_6
LCD_G_5
LCD_G_4
LCD_G_3
LCD_G_2
LCD_G_1
LCD_G_0
LCD_B_7
LCD_B_6
LCD_B_5
LCD_B_4
LCD_B_3
LCD_B_2
LCD_B_1
LCD_B_0
220
REG_GND
IR_FILTER_EN
XCS_EVF
PANEL_NOR/REV
TP_SEL1
XSTRB_FULL
XPWR_OFF
HDMI_JACK_IN
USB_SEL
SYSAD_SEL_1
MS_PWR_ON
XIC_5601_CPU_RST
MMC_PWR_ON1
VBUS_XOVR_CUR
XVBUS_DET
XMS_ACC_LED
SS
XVBUS_DET_STD_A
XPJ_RESET
XCS_IC_2801
XPHOTO_LED
TP_SEL2
LCD_DATEN
LCD_CLK
LCD_XHD
LCD_XVD
LCD_CABC_PWM
VC-658 BOARD (3/10)
CPU, AV SIGNAL PROCESS, LENS CONTROL,
MODE CONTROL, HDMI PROCESS (2/3)
XX MARK: NO MOUNT
R1421
R1467 XX
R1454
47k
R1468 XX
C1439
XX
PJ_TEMP_AD
A_2.8V
TP_SEL2
Q1402
DRA3143T0L
R1455 1M
R1460 100k
TOUCH PANEL
INTERFACE
TP_Y
TP_X
REG_GND
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-11
Page 64
12345 6 7 8 9
A
Note: IC1301 is not supplied, but this is included
in VC-658 COMPLETE BOARD (SERVICE).
IC1301 (5/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
B
C
D
D_VID_1.1V
REG_GND
A_VID_1.1V
REG_GND
REG_GND
D_1.8V_IC_1301
REG_GND
A28
A29
C1506
C1502
22u
XX
FB1501
C1501
C1505
C1507
C1504
22u
0.1u
0.1u
0.1u
B28
C1508
C1512
B29
22u
0.1u
B30
C28
C29
C30
D29
F26
G25
G26
H24
H25
H26
J24
J25
J26
K24
K25
L22
M21
M22
N21
N22
P21
P22
K22
L21
N10
P10
R10
C1509
C1513
T10
10u
0.001u
U10
V10
N1
N2
AC1
C1510
C1514
AC2
0.1u
0.1u
AK8
AL8
F31
A12
B12
A17
B17
AH30
AH31
AG29
C1515
C1511
0.1u
2.2u
AJ26
AJ27
AK27
AL27
E
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
IOVDD11_DDR
IOVDD11_DDR
IOVDD11_DDR
IOVDD11_DDR
IOVDD11_DDR
IOVDD11_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
VDD12_POP_DDR
IOVDD_FSP
IOVDD_FSP
VSS
VSS
VSS
VSS
VSS
HDMI PROCESS
Core POWER
DRAM/OneNAND
POWER
FSP
IOVDDCA_DDR
IOVDDCA_DDR
IOVDDCA_DDR
IOVDDQ_DDR1
IOVDDQ_DDR1
IOVDDQ_DDR1
IOVDDQ_DDR2
IOVDDQ_DDR2
IOVDDQ_DDR2
DDRVREF_CA
VDD18_POP_DDR
VDD18_POP_NAND
VDD18_POP_NAND
VDD18_POP_NAND
FSP_ADDR__20
FSP_ADDR__18
FSP_ADDR__17
FSP_ADDR__16
FSP_AD__15
FSP_AD__13
FSP_AD__12
FSP_AD__10
FSP_AD__9
FSP_AD__7
FSP_AD__6
FSP_AD__4
FSP_AD__3
FSP_AD__1
FSP_AD__0
FSP_XCS__0_OUT
FSP_XCS__0_IN
FSP_CLK_OUT_FLASH0
FSP_CLK_IN_FLASH0
FSP_RDY0
FSP_XRST_OUT
FSP_XOE
FSP_XWE
T1IOVDDCA_DDR
T2IOVDDCA_DDR
T3
T6
T7
T8IOVDDCA_DDR
K1IOVDDQ_DDR1
K2IOVDDQ_DDR1
K3
K6
K7
K8IOVDDQ_DDR1
AA1IOVDDQ_DDR2
AA2IOVDDQ_DDR2
AA3
AA6
AA7
AA8IOVDDQ_DDR2
C1518
C1520
0.001u
0.001u
R1DDRVREF_DQ
VSS
R2
E31
E29VSS
C1519
0.001u
F1VDD18_POP_DDR
F2
F30VDD18_POP_DDR
C1521
AK20
XX
AL20
AG30VDD18_POP_NAND
AG31
C1516
0.1u
AA24
AA25FSP_ADDR__19
AA26
AB24
AB25
AB26
AC24FSP_AD__14
AC25
AC26
AD22FSP_AD__11
AD23
AD24
AD25FSP_AD__8
AD26
AE23
AE24FSP_AD__5
AA21
AA22
AA20FSP_AD__2
AB20
AB21
AB22
AH29
AJ30FSP_XCS__2
AJ31FSP_XCS__1
AJ29
AJ28
AF24FSP_XADV
AL29
AL28
AK30
AK29
R1505 XX
AK28FSP_XRST_IN
AF23FSP_INT
C1517
XX
C1526
0.1u
C1530
C1529
C1527
0.1u
C1524
C1523
4.7u
0.1u
1u
0.1u
HB_1.2V
REG_GND
D_1.2V
REG_GND
HB_1.8VHB_1.2V
REG_GND
D_1.8V_IC_1301
REG_GND
XFLASH_RST
REG_GND
REG_GND
C1
VSS
D1
VSS
D2
VSS
E1
VSS
E2
VSS
E3
VSS
H6
VSS
J3
VSS
J6
VSS
J7
VSS
J8
VSS
L2
VSS
L3
VSS
L6
VSS
L7
VSS
L8
VSS
M7
VSS
M8
VSS
AB2
VSS
AB3
VSS
AB6
VSS
AB7
VSS
AB8
VSS
AC3
VSS
AD3
VSS
G13
VSS
H13
VSS
M10
VSS
M11
VSS
M12
VSS
M13
VSS
M14
VSS
M15
VSS
M16
VSS
M17
VSS
M18
VSS
M19
VSS
M20
VSS
N11
VSS
N12
VSS
N13
VSS
N14
VSS
N15
VSS
N16
VSS
N17
VSS
N18
VSS
N19
VSS
N20
VSS
P11
VSS
P12
VSS
P13
VSS
P14
VSS
P15
VSS
P16
VSS
P17
VSS
P18
VSS
P19
VSS
P20
VSS
R11
VSS
R12
VSS
R13
VSS
R14
VSS
R15
VSS
R16
VSS
R17
VSS
R18
VSS
R19
VSS
R20
VSS
R21
VSS
R22
VSS
H29
VSS
A27
VSS
B27
VSS
C27
VSS
R1515
F29
DDR_ZQ
240
A1
N.C.
A2
N.C.
B1
N.C.
AK1
N.C.
AL1
N.C.
AL2
N.C.
IC1301 (6/6)
AVY2G2G05A
CPU, AV SIGNAL PROCESS, CAMERA DSP,
LENS CONTROL, MODE CONTROL,
HDMI PROCESS
GND
VSS
T11
VSS
T12
VSS
T13
VSS
T14
VSS
T15
VSS
T16
VSS
T17
VSS
T18
VSS
T19
VSS
T20
VSS
T21
VSS
T22
VSS
U11
VSS
U12
VSS
U13
VSS
U14
VSS
U15
VSS
U16
VSS
U17
VSS
U18
VSS
U19
VSS
U20
VSS
U21
VSS
U22
VSS
V11
VSS
V12
VSS
V13
VSS
V14
VSS
V15
VSS
V16
VSS
V17
VSS
V18
VSS
V19
VSS
V20
VSS
V21
VSS
V22
VSS
W10
VSS
W11
VSS
W12
VSS
W13
VSS
W14
VSS
W15
VSS
W16
VSS
W17
VSS
W18
VSS
W19
VSS
W20
VSS
W21
VSS
W22
VSS
Y11
VSS
Y12
VSS
Y13
VSS
Y14
VSS
Y15
VSS
Y16
VSS
Y17
VSS
Y18
VSS
Y19
VSS
Y20
VSS
Y21
VSS
Y22
VSS
AA12
VSS
AA18
VSS
AA19
VSS
AB19
VSS
AE14
VSS
AE15
VSS
AF22
VSS
W24
VSS
Y24
VSS
Y25
VSS
F25
VSS
G24
VSS
H23
VPGM
AE22
N.C.
AL30
N.C.
AL31
N.C.
AK31
N.C.
A30
N.C.
A31
N.C.
B31
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-12
VC-658 BOARD (4/10)
CPU, AV SIGNAL PROCESS, LENS CONTROL,
MODE CONTROL, HDMI PROCESS (3/3)
XX MARK: NO MOUNT
F
Page 65
12345 6 7 8 9
A
A_1.8V
AUDIO_AGND
B
C
D_2.8V
REG_GND
D_1.8V
XSYS_RST
MCK_CN
BCK_CN
SDO
LRCK_OUT
L2701
10uH
C2701
0.01u
C2702
0.1u
C2703
0.1u
C2704
0.1u
R2701 XX
CL2705
CL2706
31
32
33
34
35
36
37
38
39
40
41
SPKR/HP
RESET
VL
VD
DGND
SDOUT
MCLK
SCLK
SDIN
LRCK
GND
33k
R2702
C2711
330p
150p
0.1u
C2708
C2707
28
29
30
AIN1A
AIN1B
26
27
AIN2B
AFILTA
AFILTB
IC2701
CS42L52-CNZR
D/A CONVERTER,
SPEAKER AMP
25
24
AIN2A
21
22
23
AIN3A/MIC1-/MIC1A
AIN3B/MIC2-/MIC1B
AIN4B/MIC2+/MIC2B
MICBIAS
AIN4A/MIC1+/MIC2A
FILT+
AGND
HP/LINE_OUTA
HP/LINE_OUTB
+VHP
FLYP
FLYN
20
VQ
19
18
17
VA
16
15
14
13
12
11
C2709
C2710 1u
1u
BEEP_PWM_P_A
A
B
C
D
SDA2SCL3AD04SPKR_OUTA+5VP6SPKR_OUTA-7SPKR_OUTB+8VP
1
I2C_SDA
I2C_SCK
MT_5.0V
E
SP_GND
REG_GND
FB2701
C2705
COM272
COM271
C2706
0.1u
10u
SP_GND
AUDIO_AGND
CL2703
CL2704
F
SPKR_OUTB-10-VHPFILT
9
L2702
L2703
L2704
L2705
10uH
10uH
10uH
10uH
SP_R-
SP_R+
SP_L-
SP_L+
VC-658 BOARD (5/10)
D
E
F
SPEAKER AMP
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-13
Page 66
12 3 4
12 3 4
A
R3006
C3002
XX
R3007
C3003
XX
220
100
C3004
XX
MCK_INOUT
BCK_OUT
LRCK_OUT
SDI1_IC_1301
B
C
SDI0_SPDIF_IN_IC_1301
SDI0_SPDIF_IN_MAG
XSYS_RST
SDI1_MAG
R3001 XX
C3001
XX
R3005
A1
B2
B1
C1
D1
0
DAO_D1
MCLK
DBDA
DBCK
XRESET
R3004
0
B3
B4
A2
A3
A4
DAI_D1
DAI_SCLK
DAO_SCLK
DAO_LRCK
DAI_LRCLK
CLOCK
A5
XINT/HS1
C2
IC3001
XBUSY/HS0
D2
C3
XX
MOSI
C4
XCSD3MISO/SDA
CLK/SCL
GND
C5
VD
B5
VL
D5
D4
R3002
R3003
XX
XX
MCK_CN
BCK_CN
D_1.2V
D_2.8V
REG_GND
A
B
C
A
B
LND00418P
1
D_3.3V
2
D_3.3V
MMC_PWR_ON1
MMC_VCC
REG_GND
MMC_CMD
REG_GND
VC-658
C
(1/10)
CN1008
(PAGE 6-9)
MMC_CLK
REG_GND
MMC_DAT_3
MMC_DAT_4
MMC_DAT_0
MMC_DAT_5
MMC_DAT_1
MMC_DAT_6
MMC_DAT_2
MMC_DAT_7
REG_GND
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
MEDIA_3.3V
18
MEDIA_3.3V
17
MMC_PWR_ON1
16
TE1_VCC
15
REG_GND
14
TE1_CMD
13
REG_GND
12
TE1_CLK
11
REG_GND
10
TE1_DAT_3
9
TE1_DAT_4
8
TE1_DAT_0
7
TE1_DAT_5
6
TE1_DAT_1
5
TE1_DAT_6
4
TE1_DAT_2
3
TE1_DAT_7
2
REG_GND
1
LND003 18P
MM-102
(1/2)
CN8101
(PAGE 6-19)
A
B
C
1234567
8
AV_SCK
XCS_MAGIC
MISO_SDA
AV_SO
XBUSY_HS0_MAGIC
XINT_HS1_MAGIC
D
E
D
E
D
E
FP-1557 FLEXIBLE BOARD
F
F
VC-MM CONECTION
(PRINTED WIRING BOARD is omitted.)
F
D
RB3001
XX
E
VC-658 BOARD (6/10)
AUDIO DSP (Not used)
F
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
08
6-14
Page 67
12345 6 7 8 9
A
D1-
CLK+
J7
IC3301
CLK+
D0+
D0-
CLK-
RB3301
Q3301
R3317
100k
XX
2
4
6
8
RB3302
XX
2
4
6
8
1
3
5
7
1
3
5
7
D0D0+
CLKCLK+
D1D1+
D2D2+
D_1.8V
XPANEL_EVF_PS_IC_1301
REG_GND
D0D0+
CLKCLK+
H5
H8
H7
F8
H9
C9
J4
J5
J6
D0-
CLK-
D0+
LS1D8LS0
CPOL
VDD_PLLA
VDD_PLLD
VDD_LVDS
VDD_LVDS
GND_PLLD
GND_PLLA
GND_LVDS
GND_LVDS
GND_LVDS
SWAP
TXEN
PCLK
GND
GND
E8
H6
G8
J9
H4
J8
J3
DE
J2
VS
H2
HS
H1
H3
G1
J1
B0
G2
B1
F1
B2
F2
B3
E1
B4
D1
B5
D2
B6
C1
XPANEL_EVF_PS
LCD_DATEN
LCD_XVD
LCD_XHD
LCD_CLK
R3316 100
LCD_R_7
LCD_R_6
LCD_R_5
LCD_R_4
LCD_R_3
LCD_R_2
LCD_R_1
LCD_R_0
D1D1+
D2+
EVF_CLK_OUT
XPANEL_EVF_PS
DRC3144E0L
EVF SWITCH
D1+
D2-
D2+
A_1.8V
REG_GND
R3301 XX
C3302
0.1u
D1-
B
G9
F9
E9
D6
D7
GND
E4
GND
E5
GND
E6
GND
E7
GND
F4
GND
F5
C
D
GND
F6
GND
F7
GND
G4
GND
G5
GND
G6
GND
G7
GND
C4
VDD
C6
VDD
C7
VDD
D3
VDD
E3
VDD
F3
VDD
G3
VDD
D9
D2-
D2+
GNDC8GNDC5GNDD4GNDD5GND
LCD SERIAL INTERFACE
D1+
SN65LVDS301ZQER
TRANSMITTER
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
GNDB9R7A8R6B8R5A7R4B7R3A6R2B6R1A5R0A1GNDB5G7A4G6B4G5A3G4B3G3A2G2B2G1B1G0E2GNDC2B7
A9
CL3302
LCD_B_1
LCD_B_0
LCD_B_2
LCD_B_3
LCD_B_4
LCD_B_5
LCD_B_6
LCD_B_7
LCD_G_0
LCD_G_2
LCD_G_1
LCD_G_3
LCD_G_4
LCD_G_5
LCD_G_6
LCD_G_7
CL3303
6-15
VC-658 BOARD (7/10)
SERIALIZER
XX MARK: NO MOUNT
E
F
Page 68
12345 6 7 8 9
A
Q4303, Q4304
BATTERY
ACV_UNREG_CN
MAIN_UNREG
BATT_UNREG_CN
CHARGE SWITCH
Q4303
DA2S10100K8
R4344
1k
3
R4345
4700
2
1
D4301
Q4304
DRC3144E0L
R4343
8.2
CPH6102-TL-E
4
5
6
B
BATT_ON
SHOE_ON
C
REG_GND
F001
1.4A 24V
F002
1.4A 24V
Q4305
8
726
5
MTM684110LS0
ACV/BATT
SELECT SWITCH
4
F003
1.4AV 24V
F004
1.4A 24V
F005
1.4A 24V
Q4307
F006
SCH1337-TL-H
Q4306
DRC3144E0L
1.4A 24V
F007
2.5A
24V
R4346
10k
R4348
Q4306, Q4307
R4347
B+ SWITCH
C4355
1u
1M
1k
1
2
D4302
DA3S103E0L
ACV_UNREG
INIT_CHARGE_ON
BATT_UNREG
ACV_ON
CORE_UNREG
I/O_UNREG
MT_UNREG
6
5
4
SHOE_UNREG
2
1
3
3
XC_UNREG
REG_GND
FR_EVER_SCK
FR_EVER_SO
FR_EVER_SI
XCS_IC_4302
MT_UNREG
CORE_UNREG
I/O_UNREG
XCS_DD
I/O_UNREG
0.1u
1u
1u
0.01u
C4319
C4325
C4322
C4320
F4
B6
F3
C6
B7
AVDD
AGND
VREF_BG
VREG_5.0VC7VREG_3.0V
TEST1
H1
TEST2
H8
TEST3
A8
CL4301
DD_ON
DD_ON
F5
R4303
47k
ROSC
B5
CS
G6
CLK
G7
DIN
F6
DOUT
E6
IC4301
BD8330AGU-E2
DC/DC CONVERER
PVDD_CPG2CP_OUTG1CFPF1CFNF2PGND_CPD6LDO1_ENBA5LDO1_OUTA6LDO1_SOURCEE5LDO2_ENBA4LDO2_OUTB4LDO2_SOURCE
H2
C4326
0.1u
1u
0.1u
C4321
C4323
1u
C4324
XX
XX
XX
XX
XX
R4308
R4307
R4306
R4305XXR4304
R4309
D3
LDO1_ON
FB1C5FB2C4FB3E4FB4E3FB5D5FB6
PVDD1a
E1
C4301
PVDD1b
PGND1a
PGND1b
SLOPE1
PVDD3a
PVDD3b
PGND3a
PGND3b
PVDD5a
PVDD5b
PGND5a
PGND5b
PVDD6a
PVDD6b
PGND6a
PGND6b
LDO2_ON
1u
1u
C4328
C4327
4.7u
E2
LX1a
LX1b
PVDD2
PGND2
LX3a
LX3b
PVDD4
PGND4
LX5a
LX5b
LX6a
LX6b
S
D1
L4301
C4311
4.7uH
D2
C1
C2
C3
C8
LX2
B8
A7
A1
B1
A2
B2
A3
B3
H6
LX4
H7
G8
H5
G5
H4
G4
H3
G3
D8
D7
E8
E7
F8
F7
10u
S
C4302
C4312
L4302
4.7u
10u
10uH
C4303
4.7u
S
L4303
C4313
10uH
10u
S
C4304
C4314
L4304
4.7u
10u
10uH
C4305
4.7u
S
L4305
C4315
10uH
10u
C4306
4.7u
S
L4306
C4316
4.7uH
10u
HB_1.8V_RG
HB_1.2V_RG
CH1_OUT
CH2_OUT
CH3_OUT
CH4_OUT
CH5_OUT
CH6_OUT
COM431
COM432
COM433
R4335
XX
COM437
R4325
XX
COM438
R4320
XX
L4308
10uH
COM440
R4313
XX
COM441
R4323
XX
COM442
R4314
XX
COM443
R4327
XX
COM444
XX
R4324
COM435
XX
R4341
XX
R4342
COM436
A_VID_1.1V
D_VID_1.1V
D_1.2V
A_1.8V
D_1.8V
A_2.8V
D_2.8V
A_3.3V
D_3.3V
J_5.0V
MT_5.0V
HB_1.8V
HB_1.2V
VO_SEL
A
B
C
CS
E3
CLK
D4
DIN
D3
DD_ON
0.1u
DD_ON
D2
ACV_UNREG
F1
BATT_UNREG
E1
VTR_UNREG
E6
ACV_ON
E2
BATT_ON
D1
AGND_COMMON
F3
10u
LANC_DC
D6
DATA_IN
B4
DATA_OUT
D5
LANC_SIG
C5
XLANC_PWR_ON
C4
XLANC_ON
C2
AGND_LANC
C6
CL4302
UNREG_IN_DET
F2
UNREG_IN
E4
VuC
F5
VuC_RST
E5
VCH
F4
EVER3
F6
C4318
1u
IC4302
BD8331GU-E2
DC/DC CONVERTER,
LANC DRIVER
ACV_UNREG
BATT_UNREG
LANC_OUT
XLANC_PWR_ON
XLANC_ON
FR_XRESET
BATT_LI_3V
EVER_3.0V
REG_GND
LANC_DC
LANC_IN
LANC_SIG
BATT_IN
XX
C4308 4.7u
R4302
SYS_DD_ON_IC_4302
BATT_ON
C4309
UNREG_IN_DET
C4310
100
ACV_ON
C4317
0.1u
Q4301
DRA3115T0L
ACV DETECT
Q4302
DRA3115T0L
BATT DETECT
R4301
XX
VOUT
R4340
D
E
F008
COM434
0.25A 50V
S
L4307 33uH
IC4303
R1207N823B-TR-FE
BL DRIVE
1
2
3
R4315
18
VIN
LX
GND
FB
R4349
18
6
VOUT
5
EN
4
C4338
C4337
1u
2.2u
BL_H
BL_L
SD_PWR_ON
D_3.3V
C4349
0.1u
MT_5.0V
LCD_CABC_PWM
F
REG_GND
IC4304
BD2224G-TR
B+ SWITCH
VIN
1
2
GND
3EN4
5
VOUT
C4350
/OC
SD_VCC
SD_VCC
R4334
1u
10k
REG_GND
LDO1_ON
PVDD_LDO1
LDO1_OUT
LDO1_FB
LDO2_ON
PVDD_LDO2
LDO2_OUT
LDO2_FB
LOAD_ON
LOAD_OUT
SGND_LDO
LOAD_IN
C1
B1
A1
B2
C4332
C4329
1u
1u
A5
A4
A3
B3
C4330
C4333
1u
1u
B5
B6
A6
C4334
C4331
1u
0.1u
A2
MSX_3.3V
COM445
XX
R4330
A_1.125V
A_1.125V_SENSE
HDMI_5V
MS_PWR_ON
MSX_3.3V
D
E
VC-658 BOARD (8/10)
DC/DC CONVERTER
XX MARK: NO MOUNT
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-16
Page 69
12345 6 7 8 9
A
B
C
D
E
EVER_3.0V
REG_GND
XCAM_LED
XCHARGE_LED
XPANEL_POWER_ON
XPOWER_TACT_SW
XEVF_SW
MSX_INS_HIZ
SD_XSDCD
XPWR_OFF
XRESET_REQ
XCS_FRONT
XFLASH_RST
XSYS_RST
FR_XRESET
INIT_CHARGE_ON
BATT/XEXT_CN
BATT_SIG
SYS_DD_ON_IC_4302
LDO1_ON
LDO2_ON
FR_EVER_SI
FR_EVER_SO
FR_EVER_SCK
XCS_IC_4302
LANC_IN
LANC_OUT
XLANC_PWR_ON
XLANC_ON
FR_SO
FR_SCK
DD_ON
XCS_DD
BATT_IN
VOUT
FR_SI
R4801
XX
COM481
SYS_DD_ON_IC_4302
C4801
47k
22u
6.3V
NENU
LDO2_ON
A5
C4
O_LDO1.8_ON
CL4818
B5
O_NENU_ON
XLANC_ON
XCS_FRONT
SD_XSDCD
A6
C5
O_DEBUG
XI_LANC_JACK_IN
FR_SI
FR_SO
B6
XPUI_RM2_IN
C4802
C4803
13p
12
3
4
13p
BATT_SIG
XPOWER_TACT_SW
XPANEL_POWER_ON
XEVF_SW
X4801
32.768kHz
CL4801
CL4802
CL4803
CL4804
CL4805
R4802
FR_XRESET
CL4816
C4808
0.1u
R4808 47k
1k
R4809
C4807
0.1u
RSTX
R4806 XX
10M
C4805
C4804
0.01u
R4807
R4803
1800
0.1u
CL4806
C4806
0.1u
RB4801
1k
1
3
5
7
CL4807
CL4808
CL4809
CL4810
CL4811
CL4812
CL4813
CL4814
K2
MOD
K1
TMD
K3
X0A
L2
X1A
L3
6800
2
4
6
8
CPO
H1
VCI
J1
BRSTX
A1
BDBMX
L1
BSIN
A11
BSOUT
B9
BSOUT
C9
BEXCK
A9
XPUIO_BATT_SIG
A4
SUBCK
K4
SUBCK
L4
AVCC
L10
AVSS
L9
AVR
K10
XPUI_POWER_ON
B4
XPUI_POWER_TACT
A3
XPUI_EJECT_SW
B3
XPUI_EVF_ON
A2
XPUI_BATTINFO_SW
B2
J3NCL11
NC
I_USB_BATT_IN
XPUI_RM3_INC1XPUI_LANC_PWR_ON
C2
B1
XLANC_PWR_ON
VBUSOK
C3
PUI_DDCON_SID2O_DDCON_SOD1XO_DDCON_SCKD3O_LDO1.2_ONE3O_LOAD_ON_FR2
CL4815
FR_EVER_SCK
FR_EVER_SO
FR_EVER_SI
LDO1_ON
B11
A10
VSS1C6VSS2F3VSS3F9VSS4G3VSS5G9VSS6J6VSS7J8VSS8J9VSS9
VCC1J2VCC2
IC4801
MB95005ABGL-G-135-ERE1
HI CONTROL,
LANC INTERFACE
O_P15
O_GPS_DD_ON
O_SYS_DD_ON_IC_4302
O_SYS_DD_ONG1XO_CS_DDCONG2O_CLAMP_ONH2XO_LANC_IC_ONH3XI_CS_EXJ4I_FR_SIL5O_FR_SOK5XI_FR_SCKJ5AI_BATT_SENSL6AI_ACV_SENSK6AI_DD_SET_SENSJ7AI_SYSTEM_SET_SENS
E1
E2
F1
F2
DD_ON
XCS_DD
SYS_DD_ON_IC_4302
MSX_INS_HIZ
BATT/XEXT_CN
C7
XPUI_RM1_IN
PUI_BATT_XEXT
FR_SCK
R4812
BATT_IN
470
R4810
A8
C8
B7
A7
I_BATT_IN
XODO_FLASH_RST
XODO_SYS_RST_S
XCA_RESET/XODO_FLASH_RST_S
O_PULLUP_SYSSET
O_FLASH_PWR_ON
XO_CHARGE/STB_LED
I_USB_CHG_READY
AI_JACK_AD_CRADLE
XO_INIT_USB_CHG
L7
XX
XX
R4813
R4811
47k
R4814
C4809
0.01u
R4815
100k
0.1u
C4810
XODO_SYS_RST
PUI_LANC_SI
O_LANC_SO
O_LOAD_ON_FR1
I_DD_S_PG
XI_RST_REQ
XI_POWER_OFF
I_ISET1_IN
O_INIT_CHARGE
XO_PWR_LED_ON
XO_GPS_RST
XO_CS_DDCON2
I_CHARGE_INH
XO_CS_IC_4302
AI_GENERAL_AD
AI_SYSTEM_AD
XI_RST_REQ_S
XI_POWER_OFF_S
I_ISET2_IN
R4816
R4819
ISETOUT2
R4817
C4811
0.01u
R4818
100k
5
Q4801
DMG964030R
DC JACK DETECT
4
3
1
6
2
8
10k
RB4802
1234567
B8
B10
C10
C11
D9
D10
D11
E9
E10
E11
F10
F11
G11
G10
H11
H10
H9
J11
J10
K9
K11
K8
L8
K7
XX
XX
47k
ACV_UNREG
BATT_UNREG
D_2.8V
10k
RB4803
8
1234567
CL4819
ACV_UNREG
BATT_UNREG
D_2.8V
D_1.8V
XSYS_RST
XFLASH_RST
LANC_IN
LANC_OUT
XRESET_REQ
XPWR_OFF
ISETOUT1
INIT_CHARGE_ON
XCAM_LED
XCHARGE_LED
USB_DD_PGOOD
USB_DD_EN
XCS_IC_4302
GENERAL_AD
SYSTEM_AD
A
B
C
D
E
VBUSOK
USB_DD_EN
USB_DD_PGOOD
ISETOUT1
ISETOUT2
NENU
SYSTEM_AD
F
GENERAL_AD
VBUSOK
USB_DD_EN
USB_DD_PGOOD
ISETOUT1
ISETOUT2
NENU
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-17
VC-658 BOARD (9/10)
HI CONTROL
XX MARK: NO MOUNT
F
Page 70
12345 6 7 8 9
A
IC9103
BD11600NUX-E2
Q9102
USB SWITCH
1
1D+
2
1D-
3
2D+
4
2D-
5
GND
4
C9102
10u
3
EVER_3.0V
VCC
10
9
S
8
D+
7
D-
6
XOE
GND
11
E5
TDPD5TDN
VB1
A5
VB2
A6
NVP
B6
CDN
C6
CDP
D6
SUSP
A3
nENU
C1
MAX14593EEWV+TG1A
GND1E6GND2B1VccB5TESTC3nSUSE3XINE2XOUTC4REG33
E1
C9103
0.1u
R9111
XX
C9104
XX
C9101
0.1u
E4
ADPD4ADN
IC9101
USB POWER
MANAGEMENT
CL9101
C9121
B2
F500
J_5.0V
Q9107
DRC3114E0L
VBUS DETECT
USB_SEL
USB_ID2
XVBUS_DET
J_5.0V
USB_VBUS
USB_ID
XVBUS_DET_STD_A
XX
Q9103
DRC3114E0L
INVERTER
IC9104
BD11600NUX-E2
USB SWITCH
1
1D+
2
1D-
3
2D+
4
2D-
5
GND
GND
11
D_2.8V
CL9102
C2
D3
D2
SDAD1SCL
nINT
nDI2C
OUT1
A1
OUT2
A2
I500
C5
ISET1
B4
ISET2
B3
LD
A4
CL9107
C9105
1u
D9101
RB480Y-40T2R
32
R9120
41
1M
VCC
D+
D-
XOE
CL9103
UNREG_IN_DET
C9107
0.1u
10
S
9
8
7
6
8
1234567
RB9101
J_5.0V
R9142
1k
D9105
RKZ5.6B2KJR1
D9104
XX
100k
VBUSOK
USB_DD_EN
USB_DD_PGOOD
ISETOUT1
ISETOUT2
CL9113
CL9110
CL9111
CL9112
CL9106
CL9108
CL9109
3
4
LF9103
1
USB_DM
2
USB_DP
C9109
0.1u
A2
A1
VBUS1
VBUS2
BD8668GW-E2
SMART POWER
SELECTOR
GNDD2INDEX/GNDC1FSETB1ICOMPD3VCOMP
E2
R9134
47k
B4
B2
A4
E1
C2
C3
B3
E5
C4
VBUSOK
EN
PGOOD
ACLEN
ISETIN1
ISETIN2
ISETIN3
ISETOUT1
ISETOUT2
IC9102
R9133
R9135
PGND
C9115
XX
SW1
SW2
GND
VFB
VFB
GND
R9138
47k
0.1u
8
1
3
6
5
8
7
6
5
4
TPS2553DBVR-1
CURRENT LIMITER
A5
C9116
C9117
B5
D5
E3
C5
E4
D4
D1
1234567
4
Q9105
XX
OUT
ILIM
X_FAULT
@CirP
IC9105
4.7u
XX
D9102
RB070M-30FJTR
C9118
10u
J_5.0V
Q9106
6
3
XX
4
DB2S31100K8
2
1
D9103
VBUS_UNLIMIT
VBUS_EN
VBUS_XOVR_CUR
MAIN_UNREG
REG_GND
5
1
C9119
IN
1u
2
GND
3
EN
R9140
47
6800
R9141
L9101
S
4.7uH
MAIN_UNREG
RB9102
2
C9112
4.7u
22k
R9137
12k
0.1
C9113
0.1u
A3
ISNS
VBUSLIM
R9136
180
C9111
C9114
XX
0.1u
C9110
XX
USB_VCC
79
68
(USB)
USB_D-
USB_D+
USB_ID
1
2
3
4
5REG_GND
CN91025P
USB_D-_MINI_AB_CN
USB_D+_MINI_AB_CN
VD9101
R9103 XX
4
2
3
1
LF9101
XX
R9102 XX
XX
USB_D-_STD
USB_D+_STD
B
R9116
100
C
MCH6341-TL-E
F009
LF9102
2A 50V
R9105
R9106
XX
4
2
3
1
XX
NENU
BUILT-IN
USB CABLE
CHARGE
D
Note: BUILT-IN USB CABLE is not included in
VC-658 COMPLETE BOARD (SERVICE).
CN9101 5P
USB_D-_STD_CN
USB_D+_STD_CN
1USB_VBUS_STD
2
3
4REG_GND
5REG_GND
6
7
B+ SWITCH
6
5
2
1
E
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-18
VC-658 BOARD (10/10)
USB INTERFACE
XX MARK: NO MOUNT
F
Page 71
12345 6 7 8 9
A
N2
N10
N12
N13
N14
P10
P12
P13
R12
R13
IC8101
R14
@CirP
@CirP
@CirPT1@CirPT2@CirPT3@CirPT5@CirP
T12
T13
U10
U12
U13
U14
V12
V13
V14
@CirP
@CirP
@CirP
@CirPV1@CirPV2@CirPV3@CirP
@CirP
@CirP
@CirP
@CirP
W1
@CirP
W2
@CirP
W3
@CirP
W7
@CirP
IC8701
MM3404A29URE
B
C8701
CN8101 18P
C
FP-1557
FLEXIBLE
LND003
(PAGE 6-14)
18MEDIA_3.3V
17MEDIA_3.3V
16MMC_PWR_ON1
15TE1_VCC
14REG_GND
13TE1_CMD
12REG_GND
11TE1_CLK
10REG_GND
9TE1_DAT_3
8TE1_DAT_4
7TE1_DAT_0
6TE1_DAT_5
5TE1_DAT_1
4TE1_DAT_6
3TE1_DAT_2
2TE1_DAT_7
1REG_GND
2.9V REG
3
4
VDD
1
VOUT
CE2GND
RB8101
2
4
6
8
RB8102
2
4
6
8
R8101
10k
R8102
XX
FB8708
100
100
R8103 XX
FB8707
1
3
R8104 XX
5
7
FB8706
R8105 XX
FB8705
R8106 XX
FB8704
1
R8107 XX
3
5
FB8703
7
R8108 XX
FB8702
R8109 XX
FB8701
R8110 XX
1u
TE1_VCC
REG_GND
TE1_CMD
TE1_CLK
TE1_DAT_3
TE1_DAT_4
TE1_DAT_0
TE1_DAT_5
TE1_DAT_1
TE1_DAT_6
TE1_DAT_2
TE1_DAT_7
REG_GND
W8
@CirP
W9
@CirP
W10
@CirP
W11
@CirP
W12
@CirP
W13
@CirP
W14
@CirP
Y1
@CirP
Y3
@CirP
Y6
@CirP
Y7
@CirP
Y8
@CirP
Y9
@CirP
Y10
@CirP
Y11
@CirP
Y12
@CirP
Y13
@CirP
Y14
@CirP
AA1
@CirP
AA2
@CirP
AA7
@CirP
AA8
@CirP
AA9
@CirP
AA10
@CirP
AA11
@CirP
AA12
@CirP
AA13
@CirP
AA14
@CirP
AE1
@CirP
AE14
@CirP
AG2
@CirP
AG13
@CirP
AH4
@CirP
AH6
@CirP
AH9
@CirP
AH11
@CirP
L4
Note: IC8101 is not supplied, but this is included in
T14
@CirP
@CirP
@CirPU1@CirPU2@CirPU3@CirPU5@CirPU6@CirPU7@CirP
MM-102 COMPLETE BOARD.
THGBM4G8D4GBAIE
INTERNAL MEMORY
D
P14
@CirPN3@CirP
@CirP
@CirP
@CirP
@CirPP1@CirPP2@CirPP3@CirP
@CirP
@CirP
@CirP
@CirPR1@CirPR2@CirPR3@CirPR5@CirP
@CirP
N1
@CirP
M14
@CirP
M13
@CirP
M12
@CirP
M10
@CirP
M9
@CirP
M8
@CirP
M5
@CirP
M3
@CirP
M2
@CirP
M1
@CirP
L14
@CirP
L13
@CirP
L12
@CirP
L3
@CirP
L2
@CirP
L1
@CirP
K14
@CirP
K13
@CirP
K12
@CirP
K11
@CirP
K10
@CirP
K9
@CirP
K8
@CirP
K7
@CirP
K5
@CirP
K3
@CirP
K1
@CirP
J14
@CirP
J13
@CirP
J12
@CirP
J11
@CirP
J10
@CirP
J9
@CirP
J8
@CirP
J7
@CirP
J1
@CirP
H14
@CirP
H13
@CirP
H12
@CirP
H11
@CirP
H10
A
B
C
D
CMDW6CLKH3DAT0H4DAT1H5DAT2J2DAT3J3DAT4J4DAT5J5DAT6J6DAT7K6VCCQW4VCCQY4VCCQ
W5
TE1_CMD
TE1_CLK
TE1_DAT_0
TE1_DAT_1
TE1_DAT_2
TE1_DAT_3
TE1_DAT_4
TE1_DAT_5
TE1_DAT_6
E
TE1_DAT_7
TE1_VCC
REG_GND
R8111
0
R8112
XX
R8113
XX
F
AA3
VCCQ
AA5
VCCQM6VCCN5VCC
C8102
4.7u
VCCU9VCCK2VDDIK4VSSQM7VSSP5VSS
T10
C8104
0.1u
C8103
0.1u
VSSU8VSSY2VSSQY5VSSQ
R10
C8105
XX
VSSQ
VSSQA4@CirPA6@CirPA9@CirP
AA4
AA6
@CirPB2@CirP
@CirPD1@CirP
A11
@CirPH1@CirPH2@CirPH6@CirPH7@CirPH8@CirPH9@CirP
B13
D14
MM-102 BOARD (1/2)
E
F
INTERNAL MEMORY
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-19
Page 72
12345 6 7 8 9
U20
V16
V18
V19
V20
W16
W18
W19
W20
Y11
Y18
Y19
Y20
AA7
AA8
AA9
AA11
AA18
AA19
AA20
AB7
AB8
AB9
AB12
AB13
AB16
AB18
AB19
AB20
AC7
AC8
AC9
AC18
AC19
AC20
AD7
AD8
AD9
AD13
AD14
AD15
AD16
AD17
AD18
AD19
AD20
AE4
AE5
AE7
A
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirPY7@CirPY8@CirPY9@CirP
@CirP
@CirP
@CirP
@CirPW7@CirPW8@CirPW9@CirP
U19
@CirP
@CirPV7@CirPV8@CirPV9@CirP
A
@CirP
AE9AE12AE13AE14AE15AE16AE17AE18AE19AE20AE22AE23AF4AF5AF7AF8AF13AF14AF15AF16AF17AF18AF19AF20AF22AF23AG4AG5AG22AG23AH4AH5AH6AH7AH8AH19AH20AH21AH22AH23AJ4AJ5AJ6AJ7AJ8AJ19AJ20AJ21AJ22AJ23AR1AR26AU3AU24AV6AV9AV12AV15AV18AV21
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
B
C
D
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
Note: IC8201 is not supplied, but this is included in
MM-102 COMPLETE BOARD.
IC8201
THGBM4G9D8GBAII
INTERNAL MEMORY
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
@CirP
U18
U16
U15
U14
U11
U9
U8
U7
T20
T19
T18
T10
T9
T8
T7
R20
R19
R18
R17
R16
R15
R14
R13
R11
R9
R7
P23
P22
P20
P19
P18
P17
P16
P15
P14
P13
P7
P5
P4
N23
N22
N20
N19
N18
N17
N16
N15
N14
N13
N12
N8
N7
N5
N4
M23
M22
M5
M4
L23
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
TE1_CMD
TE1_CLK
TE1_DAT_0
TE1_DAT_1
TE1_DAT_2
TE1_DAT_3
TE1_DAT_4
TE1_DAT_5
TE1_DAT_6
TE1_DAT_7
TE1_VCC
REG_GND
R8201
CMD
CLKN9DAT0
DAT1
DAT2P8DAT3P9DAT4
DAT5
DAT6
DAT7
VccQ
VccQ
VccQ
VccQ
VccQ
Vcc
Vcc
Vcc
VccR8VDDi
VssQ
Vss
Vss
Vss
Vss
VssQ
VssQ
VssQ
VssQ
RST_nA6@CirPA9@CirP
@CirP
@CirP
@CirP
@CirPB3@CirP
@CirPD1@CirP
AD12
N10
N11
P10
P11
P12
R12
AD10
AE10
AF9
AF11
U12
V11
AA16
AB15
R10
U13
W11
Y16
AB14
AE8
AE11
AF10
AF12
AB11
A12
A15
A18
AD11
0
R8202
C8205
C8204
C8202
C8203
4.7u
0.1u
R8203
XX
XX
XX
0.1u
A21
B24
D26
@CirPK4@CirPK5@CirPK6@CirPK7@CirPK8@CirP
@CirP
@CirP
@CirP
@CirP
K20
K21
@CirPL4@CirPL5@CirPL6@CirPL7@CirPL8@CirP
K22
K23
K19
@CirP
@CirP
@CirP
@CirP
L19
L20
L21
L22
E
MM-102 BOARD (2/2)
F
INTERNAL MEMORY
XX MARK: NO MOUNT
6-20
Page 73
12345 6 7 8 9
A
10uH
AU_2.8V
B
AUDIO_GND
REG_GND
AU_2.8V_IC_2801
C
L2601
L2602
10uH
C2601
10u
C2602
10u
R2605
6800
R2606
6800
C2607
MIC_JACK_IN
CL2601
0.1u
C2609
1u
1u
B1
E5
F1
F3
F2
F5
C2614
0.1u
C2615
F4
B2
D4
MIC_PWR_ON
A
B
C
SVDD
C2608
0.001u
EXT_MIC_R
EXT_MIC_L
D
AUDIO_R_I/O
AUDIO_L_I/O
MICAMP_OUT_R
MICAMP_OUT_L
EXT_LINE_SEL
R2601 120k
R2602 120k
10k
R2603
R2604 10k
C2603 0.1u
C2604 0.1u
C2605 0.1u
C2606 0.1u
C2610
0.001u
MIC_INR1
E3
MIC_INR2
D1
MIC_INL1
C1
MIC_INL2
D3
LINE_INR
E1
LINE_INL
C2
LINE_OUTR
E2
LINE_OUTL
C5
MIC_BIASL
MIC_BIASR
PATH_SEL0B4PATH_SEL1A3QSTARTD2VCOMA2MGNDA5PGNDA4C1PB5C1NA6PVSS
A1
E
MIC_SEL1
MIC_SEL0
BD8871GW-E2
C2611 1u
MIC_EXT
IC2601
MIC/HP
AMP
MIC_PDB
MIC_MONO
C2612 1u
MVDD
C2613
2.2u
HP_OUTL
HP_OUTR
HP_INL
HP_INR
HP_PDB
SGND
PVDD
SVSS
RB2602
22
78
E4
E6
D5
D6
C6
B6
B3
C2616
F6
2.2u
56
34
12
C2617 1u
C2618 1u
HP_L_OUT
HP_R_OUT
HP_PRE_OUT_L
HP_PRE_OUT_R
HP_PS
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-21
RH-014 BOARD (1/5)
MIC/HP AMP
XX MARK: NO MOUNT
F
Page 74
12345 6 7 8 9
A
D_2.8V
REG_GND
IC_2801_CP_GND
XX
C2846XXC2847
L2804
L2802
L2803
C2801
C2802
A_2.8V
VIDEO_GND
B
AU_2.8V
AUDIO_GND
IC_2801_CP_GND
EXT_LINE_SEL
MICAMP_OUT_L
MICAMP_OUT_R
C
2200
2200
2200
R2804
R2805
INT_MIC_L
INT_MIC_R
INT_MIC_F
D
SHOE_MIC_FL
SHOE_MIC_FR
R2801
C2803
0.001u
C2804
0.001u
R2827
R2828
C2805
C2806
C2807
22k
22k
C2810
1u
10uH
C2852
4.7u
10uH
10uH
0.015u
0.015u
0.015u
C2814
22u
C2815
10u
1u
1u
C2853
0.001u
33k
33k
R2813
R2811
AU_2.8V_IC_2801 AU_2.8V_IC_2801
C2854
C2855
0.001u
0.001u
C2817
0.015u
C2818
0.015u
C2820
C2822
C2823
C2824
C2821
R2802 XX
C2835 1u
C2832
4.7u
1u
0.1u
0.1u
0.1u
R2816
100k
C2830
C2828
C2829
C2831
L11
M12
L12
K11
K12SIJ11
J12SOH11
H12
G12
G11
F11
F12
E11
E12
D11
D12
C11
C12
B12
CLK
XCS
AUX_L
AUX_R
MONITOR_RR
B11
MONITOR_L
A12
F_INT_L
A11
F_INT_R
A10
F_SHOE_L
B10
F_SHOE_R
B9
R_INT_L
4.7u
0.1u
0.1u
0.1u
0.1u
A9
B8
A8
B7
A7
B6
A6
A5
B5
B4
A4
B3
A3
A2
VREF_AU
R_SHOE_L
GND_AU
R_SHOE_R
MICVCC
MONITOR_R
VCC_AU
OFFSET_PBL
OFFSET_PBR
OFFSET_SP
BEEP_IN
VCC_SP
VREF_SP
MONITOR_FL
OFFSET_FR
MONITOR_FR
VCC_AU
AGC_TC
HP_JACKIN
OFFSET_FL
NN12926A-BB
VIDEO/AUDIO PROCESSOR
IC2801
HP_PS
EXT_LINE_SEL
VREG
MICJACKIN
XSYS_RESET
XMICMONO
MONITOR_RL
HP_PRE_OUT_L
HP_PRE_OUT_R
SDTO1
SDTO2
VCC_D
GND_D
GND_AU
GND_Y
VCC_V
C/Pb_IN
GND_C
MCLK
WCLK
BCLK
M11
M10
L10
L9
M9
SDTI
L8
L7
M8
M7
L6
M6
L5
Y_IN
M5
M4
ID3
L4
L3
ID2
M3
Pr_IN
M2
ZAP
M1
L2
C2837
0.1u
C2849
C2850
C2841
0.1u
1u
1u
C2842
XX
CL2801
CL2802
CL2803
AV_SCK
AV_SO
XCS_IC_2801
XSYS_RST
BCK_CN
MCK_CN
LRCK_OUT
SDI0_SPDIF_IN_MAG
SDI1_MAG
SDO
HP_PS
HP_PRE_OUT_L
HP_PRE_OUT_R
DAC_IOUT_Y
DAC_IOUT_PB
A
B
C
D
E
REG_GND
AUDIO_L_I/O
AUDIO_R_I/O
REG_GND IC_2801_CP_GND
REG_GND VIDEO_GND
COM281
COM282
COM283
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
SP+B1SP+B2SP_GNDC1SP-D1SP-C2LINEOUT_LD2GND_AUE2LINEOUT_RE1VCC_CPF1PC1F2GND_CPG1PC2G2VSS_OUTH1VSS_INH2SDCJ1Y_OUTJ2ID1K2V/Pr_OUTK1VCC_DRVL1C/Pb_OUT
A1
10u
100
100
R2815
C2834
10u
C2836
R2829 75
COMPO_VIDEO
R2814
C2833
0.1u
AUDIO_GNDREG_GND
RH-014 BOARD (2/5)
E
F
VIDEO/AUDIO PROCESSOR
XX MARK: NO MOUNT
6-22
Page 75
12345 6 7 8 9
A
EVER_3.0V
XEVF_SW
B
IC6401
MM3404A25URE
1u
XPANEL_EVF_PS
D_1.8V
2.5V REG
4
1
VDD
3
VOUT
CE2GND
R6402
R6401
C6405
1u
XX
XX
J_5.0V
R6414 0
C
C6403
REG_GND
EP_2.5V
REG_GND
Q6401
FK3303010L
INVERTER
EVER_3.0V EVER_3.0V
R6415
XX
3
4
SE6401
GMR
EVF
PULL OUT
DETECT
C6411
0.1u
12
C6410
EP_2.5V
XX
A
B
C
0.1u
XX
C6404
C6402
0.1u
D
1
2DIR
EVF_CLK_OUT
LCD_XHD
LCD_XVD
2
1A1
3
1A2
4
2A1
14
16
1DIR
IC6402
TC7MP3125FTG (EB)
LEVEL SHIFT
2A2
GND7GND82B2
6
5
C6401
0.1u
13
1OE
VccB15VccA
1
2OE
12
1B1
11
1B2
10
9
2B1
8
EVF_CLK_OUT_EVF_CN
1234567
RB6401
10k
EVF_VS_EVF
EVF_HS_EVF
LCD_B_0
LCD_B_1
LCD_B_2
LCD_B_3
LCD_B_4
LCD_B_5
LCD_B_6
LCD_B_7
3
5
7
RB6407
1
3
5
7
RB6406
2
4
6
8
XX
2
4
6
8
XX
E
F
R6408
19
22
2OE201OE21GND
VccA231DIR242DIR
RB6404
XX
78
56
34
12
RB6405
XX
78
56
34
12
R6405
XX
R6412 XX
R6413 XX
EVF_PDB0_CN
EVF_PDB1_CN
EVF_PDB2_CN
EVF_PDB3_CN
EVF_PDB4_CN
EVF_PDB5_CN
EVF_PDB6_CN
EVF_PDB7_CN
EVF_CLK_OUT_EVF_CN
EVF_HS_EVF
EVF_VS_EVF
RB6403
EVF_PDB0_CN
EVF_PDB1_CN
EVF_PDB2_CN
EVF_PDB3_CN
EVF_PDB4_CN
EVF_PDB5_CN
EVF_PDB6_CN
EVF_PDB7_CN
1234567
1234567
10k
8
1A1
1
1A2
2
1A3
3
1A4
4
2A1
5
2A2
6
IC6403
TC7MP3245FTG(EB,A)
LEVEL SHIFT
GND10VccB112B4122B3
2A382A4
9
7
C6406
0.1u
1B1
18
1B2
17
1B3
16
1B4
15
2B1
14
2B2
13
8
RB6402
10k
EVF_PDB0_CN
EVF_PDB1_CN
EVF_PDB3_CN
EVF_PDB4_CN
EVF_PDB5_CN
EVF_PDB7_CN
EVF_CLK_OUT_EVF_CN
RH-014 BOARD (3/5)
D
E
F
LEVEL SHIFT
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-23
Page 76
12345 6 7 8 9
A
MIC901
MICROPHONE
UNIT
J_5.0V
61
J_5.0V
60
J_5.0V
59
J_5.0V
58
J_5.0V_GND
57
J_5.0V_GND
56
J_5.0V_GND
55
J_5.0V_GND
B
C
XPANEL_EVF_PS
EVF_CLK_OUT
SHOE_MIC_FL
SHOE_MIC_FR
D
SDI0_SPDIF_IN_MAG
DAC_IOUT_PB
E
FP-1522
FLEXIBLE
LND002
(PAGE 6-37)
D_1.8V
XSTRB_FULL
STROBE_ON
I2C_SCK
I2C_SDA
XCS_EVF
AV_SCK
AV_SO
REG_GND
LCD_B_7
LCD_B_6
LCD_B_5
LCD_B_4
LCD_B_3
LCD_B_2
LCD_B_1
LCD_B_0
REG_GND
LCD_XVD
LCD_XHD
REG_GND
REG_GND
XBB_RST
XEVF_SW
EVER_3.0V
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
AUDIO_GND
AUDIO_GND
BATT_LI_3V
A_2.8V
REG_GND
SDI1_MAG
MCK_INOUT
LRCK_OUT
BCK_OUT
XCS_IC_2801
XSYS_RST
LANC_DC
JACK_AD
LANC_SIG
FR_XRESET
REG_GND
DAC_IOUT_Y
REG_GND
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
SDO
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN700161P
J_5.0V
J_5.0V_GND
D_1.8V
XSTRB_FULL
STROBE_ON
I2C_SCK
I2C_SDA
XCS_EVF
AV_SCK
AV_SO
LCD_B_7
LCD_B_6
LCD_B_5
LCD_B_4
LCD_B_3
LCD_B_2
LCD_B_1
LCD_B_0
XPANEL_EVF_PS
LCD_XVD
LCD_XHD
EVF_CLK_OUT
XBB_RST
XEVF_SW
EVER_3.0V
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
SHOE_MIC_FL
SHOE_MIC_FR
AUDIO_GND
BATT_LI_3V
A_2.8V
SDO
SDI1_MAG
SDI0_SPDIF_IN_MAG
MCK_CN
LRCK_OUT
BCK_CN
XCS_IC_2801
XSYS_RST
LANC_DC
JACK_AD
LANC_SIG
FR_XRESET
DAC_IOUT_PB
DAC_IOUT_Y
REG_GND
A_2.8V
R7001
R7002
COM701
COM702
XX
XX
D_2.8V
AU_2.8V
LED1_3_K
XX
LED2_K
HP_R_OUT
HP_L_OUT
REG_GND
VDR701
VDR702
XX
AUDIO_L
LANC_SIG
REG_GND
LANC_DC
AUDIO_R
JACK_AD
REG_GND
VIDEO_I/O
A_GND
S_C_I/O
S_Y_I/O
VOUT_LED_A
REG_GND
11
12
A/V R
13
14
EXT_MIC_L
EXT_MIC_R
AUDIO_GND
HP_JACK_IN
CN7003 22P
22 LED1_3_K
21 LED1_3_K
20 LED1_3_K
19 LED1_3_K
18 LED1_3_K
17 VOUT_LED_A
16 VOUT_LED_A
15 VOUT_LED_A
14 VOUT_LED_A
13 VOUT_LED_A
12 VOUT_LED_A
11 VOUT_LED_A
10 VOUT_LED_A
9 VOUT_LED_A
8 VOUT_LED_A
7 LED2_K
6 LED2_K
5 LED2_K
4 LED2_K
3 LED2_K
2 REG_GND
CN7002
1TH
1
2
3
4
5
6
7
8
9
10
100p
C7001
C7003
C7002
FB7001
FB7002
FB7011
FB7010
100p
VDR709
0.1u
0.1u
C7004
TH
R7008
0
VDR710
REG_GND
C7005
FLEXIBLE
FB7005
FB7006
FB7003
FB7004
XX
FP-1555
LND721
(PAGE 6-7)
VDR703
R7009
0
R7003
XX
R7010
VDR704
0
VDR705
S7001
RESET
1
2
C7006
470p
2
4
1
3
2
4
1
3
CN7004
6P
6INT_MIC_R
5AUDIO_GND
4INT_MIC_L
3AUDIO_GND
2INT_MIC_F
1AUDIO_GND
3
XX
4
VDR706
R7004
100k
C7007
C7008
470p
XX
J7001
PLUG IN POWER
J7002
(HEADPHONE)
INT_MIC_R
INT_MIC_L
INT_MIC_F
AUDIO_GND
D_2.8V
AUDIO_L_I/O
AUDIO_R_I/O
LANC_SIG
JACK_AD
LANC_DC
COMPO_VIDEO
REG_GND
FR_XRESET
REG_GND
Note: MIC901 and EVF BLOCK are not
included in RH-014 COMPLETE BOARD.
LCD902
COLOR
EVF
UNIT
BATT_LI_3V
VDR707
XX
VDR708
XX
REG_GND
CN7005 22P
VDD
GND
NRESET
CLOCK
HSYNC
VSYNC
VALID
DATA0
DATA1
DATA2
DATA3
N.C.
DATA4
DATA5
DATA6
DATA7
SDAT
N.C.
SCLK
SEN
GND
VCC2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
C7009
R7007
C7010
XX
XX
XX
EP_2.5V
XBB_RST
EVF_CLK_OUT_EVF_CN
EVF_HS_EVF
EVF_VS_EVF
EVF_PDB0_CN
EVF_PDB1_CN
EVF_PDB2_CN
EVF_PDB3_CN
EVF_PDB4_CN
EVF_PDB5_CN
EVF_PDB6_CN
EVF_PDB7_CN
AV_SO
AV_SCK
XCS_EVF
J_5.0V
REG_GND
Note: BT7001 is not included in RH-014 COMPLETE BOARD.
BT7001
LITHIUM
BATTERY
BH7001
BATTERY HOLDER
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-24
RH-014 BOARD (4/5)
CONNECTORS
XX MARK: NO MOUNT
F
Page 77
12345 6 7 8 9
A
C4
D4
B1
B2
B3
L7201
2.2uH
TS
GPIO/PG
SDA
SCL
HC_SEL
R7201
10k
D3
C3
C1SWC2SWA3
Tx-MASK
ENDCL/NRESET
IC7201
TPS61305YFFR
LED FLASH
DRIVE
Note: C7207 is not included in
RH-014 COMPLETE BOARD.
R7207
XX
R7206
XX
BAL
C7207
350u
VOUT
INDLED
LED1
LED2
LED3
A2
A1
E2
E1
E3
CL7203
5.5V
R7213
220
13
2
R7214
220
C7204
10u
R7208 XX
R7210 XX
R7209 XX
TH
VOUT_LED_A
LED1_3_K
LED2_K
C7206
FB7201
R7203
XX
10k
J_5.0V
D_2.8V
B
XSYS_RST
C
XSTRB_FULL
I2C_SDA
I2C_SCK
R7204 XX
C7205
CL7201
CL7202
C7201
10u
XX
A
B
C
C7208
220p
STROBE_ON
D
XSYS_RST
REG_GND
E
R7212 3300
COM721
COMMON-GND2
D7201
1SS357
A_GND
J_5.0V_GND
REG_GND
A_GND
VDR721
J_5.0V_GND
REG_GND
XX
C7209
XX
FLASH_SYNC
A4
B4
E4
D2
C7202
10u
C7203
0.01u
D
E
AVIND1PGND
PGND
AGND
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-25
RH-014 BOARD (5/5)
LED FLASH DRIVE
XX MARK: NO MOUNT
F
Page 78
12345 6 7 8 9
A
FP-1518
FLEXIBLE
LND002
(PAGE 6-37)
B
CN9601
SHUTTER_XA
SHUTTER_XA
D_2.8V
DIAL_B
DIAL_A
12
11
10SHUTTER_A
9SHUTTER_A
8REG_GND
7IR_LED_ON
6SIRCS_SIG
5
4XTALLY_LED
3KEY_AD3
2
1
12P
SHUTTER_XA
SHUTTER_A
REG_GND
IR_LED_ON
SIRCS_SIG
D_2.8V
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
DIAL_A
DIAL_B
KEY_AD3
REG_GND
C9603
0.01u
C9604
0.01u
R9606
100
R9607
100
XX
VD9601
VD9602
CN9602 6P
XX
1 DIAL_A_CN
2 REG_GND
3 REG_GND
4 REG_GND
5 DIAL_B_CN
6 KEY_AD3
CONTROL
SWITCH
BLOCK
(RS39900)
Note: CONTROL SWITCH BLOCK (RS39900) and
LENS BARRIER UNIT are not included
A
B
in FR-319 COMPLETE BOARD.
D_2.8V
C
IR_LED_ON
REG_GND
R9601
1k
R9603
R9604
22
18
Q9601
DSC500200L
LED DRIVE
C9602
XX
D9601
SML-J13RWT96
(NIGHTSHOT)
3
4
1
2
SHUTTER_A
SHUTTER_XA
REG_GND
C9605
2 SHUTTER_A
1 SHUTTER_XA
CN9603
C9606
XX
XX
2P
LENS
BARRIER
UNIT
C
Note: Q9601 is not supplied, but this is
included in FR-319 COMPLETE BOARD.
D
D9602
SML-D12V8WT86SN
(TALLY)
D_2.8V
XTALLY_LED
R9605
470
E
D_2.8V
REG_GND
SIRCS_SIG
F
R9602
C9601
47
1u
1
2
GND1
VCC
GND24OUT
3
IC9601
RS-470
SIRCS
FR-319 BOARD
D
E
F
FRONT CABINET SECTION
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-26
Page 79
12 3 4
12 3 4
A
VREF
C7703
0.047u
GND
2
1
XX
R7704
C7705
22u
C7704
0.047u
1
2
3
4
5
HI1
LO1
6
LIA1
7
LIB1
8
GND
9
LIB2
LIA2
10
NJM3230SE7
ROLL SENSOR
LO212HI213HO214VREF215AM2
11
IC7701
AMP
HO1
VREF1
AM1
OUT1
NC
CRST
OUT2
C7706
0.33u
10k
R7706
15k
R7705
L7701
10uH
470k
R7707
20
19
V+
18
17
16
C7707
4.7u
A_2.8V
ROLL_AD
VST_C_CHARGE
3
VCC
4
OUT
B
XX
R7701
32.2kHz
ROLL SENSOR
C7702
0.1u
SE7701
C
22k
C7701
0.1u
R7702
R7703
22k
D
A
B
C
D
A
B
A_2.8V
D_2.8V
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
SS
2
1
LND00120P
REG_GND
VST_C_CHARGE
REG_GND
ROLL_AD
REG_GND
XPOWER_TACT_SW
KEY_AD2
VC-658
(1/10)
C
CN1007
(PAGE 6-9)
REG_GND
XCAM_LED
XPHOTO_LED
REG_GND
EVER_3.0V
XCHARGE_LED
REG_GND
ZOOM_VR_AD
KEY_AD1
REG_GND
20
REG_GND
A_2.8V
19
VST_C_CHARGE
18
17
REG_GND
16
ROLL_AD
REG_GND
15
XPOWER_TACT_SW
14
13
KEY_AD2
12
REG_GND
11
D_2.8V
10
XCAM_LED
9
XPHOTO_LED
REG_GND
8
7
EVER_3.0V
XCHARGE_LED
6
5
REG_GND
4
ZOOM_VR_AD
SS
3
2
KEY_AD1
REG_GND
1
LND002 20P
CK-244
(2/2)
CN9001
(PAGE 6-28)
D
A
B
C
D
REG_GND
E
CK-244 BOARD (1/2)
ROLL SENSOR
F
08
XX MARK: NO MOUNT
E
E
E
FP-1521 FLEXIBLE BOARD
F
F
08
VC-CK CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-27
Page 80
12345 6 7 8 9
A
CONTROL
Note: CONTROL SWITCH BLOCK (PS39900) is not
included in CK-244 COMPLETE BOARD.
SWITCH
BLOCK
(PS39900)
B
CN9002 10P
1 D_2.8V
2 ZOOM_VR_AD
3 REG_GND
4SS
5 EVER_3.0V
6 XCHARGE_LED
7 PHOTO_FREEZE
8 PHOTO_REC
9 REG_GND
10 REG_GND
34
XX
VD9005
S9006
MODE
12
R9004
D_2.8V
KEY_AD1
ZOOM_VR_AD
KEY_AD2
XX
REG_GND
R9008
REG_GND
SS
XCHARGE_LED
EVER_3.0V
XPHOTO_LED
XCAM_LED
D_2.8V
XPOWER_TACT_SW
ROLL_AD
VST_C_CHARGE
A_2.8V
A_2.8V
1
2KEY_AD1
3
SS
4ZOOM_VR_AD
5REG_GND
6
7EVER_3.0V
8
9XPHOTO_LED
10XCAM_LED
11D_2.8V
12REG_GND
13KEY_AD2
14
15
16ROLL_AD
17REG_GND
18
19
20REG_GND
REG_GND
XCHARGE_LED
REG_GND
C
XPOWER_TACT_SW
REG_GND
VST_C_CHARGE
CN9001 20P
D
FP-1521
FLEXIBLE
LND002
(PAGE 6-27)
10k
R9005
10k
R9006
R9007
C9001
1M
R9002
XX
R9003
XX
1M
C9002
XX
XX
C9003
XX
D_2.8V
ZOOM_VR_AD
EVER_3.0V
XCHARGE_LED
KEY_AD1
REG_GND
R9010
R9011
1k
120
8
7
RB9001
5
2200
6
3
4
2
1
45
D9003
XX
12 3
SS
A
B
C
D
R9001
D_2.8V
XCAM_LED
180
E
XPHOTO_LED
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
D9001
CL-271SYG-C-TS
(MOVIE)
D9002
CL-271SYG-C-TS
(PHOTO)
XPOWER_TACT_SW
REG_GND
6-28
VD9001
1
2
4
3
6
5
7
8
RB9002
R9012
6800
S9001
POWER
2
1
XX
4
3
S9002
PROJECTOR
1
3
2
VD9002
XX
4
S9003
LIGHT
2
1
4
3
VD9003
S9004
NIGHTSHOT
2
1
XX
4
3
VD9004
2200
S9005
2
1
XX
4
3
CK-244 BOARD (2/2)
VD9006
KEY_AD2
E
XX
F
CONTROL KEYS
XX MARK: NO MOUNT
Page 81
12345 6 7 8 9
R6037
XX
EP_2.8V
TP_SEL1
TP_Y
TP_X
DB2S31100K8
R6040
XX
D6002
R6042 1k
R6041 1k
R6043 1k
R6044
C6020
1u
C6021
0.47u
C6022
1u
C6029
4.7u
C6023
4.7u
C6030
1u
C6031
1u
C6024
4.7u
C6025
4.7u
C6032
1u
C6026
2.2u
C6033
1u
C6019
4.7u
C6027
1u
XX
C6034
XX
XCS_LCD
AV_SO
AV_SCK
XBB_RST
EP_2.8V
A_1.8V
LCD_VD
LCD_HD
LCD_CK
LCD_DB0
LCD_DB1
LCD_DB2
LCD_DB3
LCD_DB4
LCD_DB5
LCD_DB6
LCD_DB7
LCD_DG0
LCD_DG1
LCD_DG2
LCD_DG3
LCD_DG4
LCD_DG5
LCD_DG6
LCD_DG7
LCD_DR0
LCD_DR1
LCD_DR2
LCD_DR3
LCD_DR4
LCD_DR5
LCD_DR6
LCD_DR7
REG_GND
L6001
10uH
L6002
10uH
CL6004
CL6005
CL6006
CL6001
CL6007
CL6002
CL6008
CL6003
CL6009
BL_L
BL_H
PD-465 BOARD (1/2)
LCD
XX MARK: NO MOUNT
CN6003
61P
1 NVDM(TEST-PIN)
2 XCS
3 SI
4
XSCK
5
XRST
6 SO(TEST-PIN)
7 VREF
8 DVDD
9V
SS
10 VDD
11 VGM
12 VCOM-IN
13 VCOM-DC
14 VCOM-AC
15 VBRT
16 AVDCF1N
17 AVDCN1P
18 ADVCN2N
19 AVDCN2P
20 AVDD
21 VSS
22 VDD
23 PVDCFN
24 PVDCFP
25 PVDD
26 NVDLCFP
27 NVDLCFN
28 NVDD
29 VDDIO
30 DE
31 XVD
32 XHD
33 DCLK
34 DB0
35 DB1
36 DB2
37 DB3
38 DB4
39 DB5
40 DB6
41 DB7
42 DG0
43 DG1
44 DG2
45 DG3
46 DG4
47 DG5
48 DG6
49 DG7
50 DR0
51 DR1
52 DR2
53 DR3
54 DR4
55 DR5
56 DR6
57 DR7
GND
58
59 N.C
60 BL-
61
BL+
Note: LCD901 is not included in
PD-465 COMPLETE BOARD.
LCD901 (1/2)
(LCD MODULE)
3.0 INCH
WIDE COLOR
LCD
LCD BACKLIGHT
A
B
C
D
E
F
0.0047u
R6016
R6017
C6002
XX
XX
PJ-104
CN8503
(PAGE 6-31)
(1/4)
Q6001, Q6002
TOUCH PANEL
INTERFACE
C6003
0.0047u
3
VDDNCGND
4
OUT
SE6001
GMR
PANEL
NORMAL/REVERSE
DETECT
XPJ_PARK
PJ_PWR_EN
PJ_TEMP_AD
LCD_VD
REG_GND
LCD_DB0
LCD_DB2
LCD_DB6
DMG9640N0R
DMG9640N0R
C6001
0.1u
12
1REG_GND
3I2C_SDA
5I2C_SCK
7
9LCD_DATEN
11REG_GND
13
15LCD_HD
17
19LCD_CK
21REG_GND
23
25LCD_DB1
27REG_GND
29
31LCD_DB3
33REG_GND
35LCD_DB4
37LCD_DB5
39REG_GND
41
43LCD_DB7
45REG_GND
47LCD_DG3
49LCD_DG2
51REG_GND
53LCD_DG1
55LCD_DG0
57REG_GND
59REG_GND
Q6001
Q6002
4
6
2
2
5
3
1
6
4
5
3
1
REG_GND
I2C_SDA
I2C_SCK
PJ_TEMP_AD
LCD_DATEN
REG_GND
LCD_VD
LCD_HD
REG_GND
LCD_CK
REG_GND
LCD_DB0
LCD_DB1
REG_GND
LCD_DB2
LCD_DB3
REG_GND
LCD_DB4
LCD_DB5
REG_GND
LCD_DB6
LCD_DB7
REG_GND
LCD_DG3
LCD_DG2
REG_GND
LCD_DG1
LCD_DG0
REG_GND
REG_GND
FP-1519
FLEXIBLE
CN6001 61P
D0-
N.C
D0+
REG_GND
CLK-
N.C
CLK+
REG_GND
REG_GND
REG_GND
D1-
N.C
D1+
REG_GND
D2-
N.C
D2+
REG_GND
REG_GND
SP_R-
SP_R+
REG_GND
REG_GND
D_2.8V
XGPS_RST
REG_GND
REG_GND
PANEL_NOR/REV
I2C_SDA
XPJ_RESET
REG_GND
I2C_SCK
PJ_PWR_EN
REG_GND
D_3.3V
GPS_UART_RXD
GPS_UART_TXD
REG_GND
REG_GND
REG_GND
A_5.0V
A_5.0V
A_5.0V
TP_SEL1
GPS_UART_CTS
GPS_UART_RTS
BL_H
BL_L
TP_Y
TP_X
XPJ_PARK
XCS_LCD
AV_SO
A_1.8V
AV_SCK
PJ_TEMP_AD
XBB_RST
REG_GND
SP_L+
SP_L-
SP_L-
SP_L+
SP_R-
SP_R+
LND003
(PAGE 6-35)
LN6001
CH_GND
61REG_GND
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
XX
25
24
XX
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
D0-
D0+
CLK-
CLK+
D1-
D1+
D2-
D2+
SP_R-
SP_R+
XGPS_RST
PANEL_NOR/REV
PJ_PWR_EN
D_3.3V
R6035
GPS_UART_RXD
GPS_UART_TXD
R6034
A_5.0V
TP_SEL1
R6033XX
GPS_UART_CTS
GPS_UART_RTS
R6032XX
BL_H
BL_L
TP_Y
TP_X
XPJ_PARK
XCS_LCD
AV_SO
AV_SCK
PJ_TEMP_AD
XBB_RST
SP_L+
SP_L-
REG_GND
Note: SP901 and SP902 are not included
in PD-465 COMPLETE BOARD.
CN6004 2P
1SP_L-
SP_L+
2
CN6005 2P
1SP_R-
2SP_R+
R6002
R6006
R6012
XX
XX
XX
SP901
(SPEAKER (L))
SP902
(SPEAKER (R))
EP_2.8V
I2C_SDA
XPJ_RESET
I2C_SCK
A_1.8V
LCD901 (2/2)
(LCD MODULE)
TOUCH
PANEL
CN6002
REG_GND
TP_L
TP_R
TP_TOP
TP_BOT
REG_GND
A_5.0V
XPJ_RESET
XPJ_PARK
PJ_PWR_EN
D_3.3V
REG_GND
LCD_DR7
LCD_DR6
REG_GND
LCD_DR5
LCD_DR4
REG_GND
LCD_DR3
LCD_DR2
REG_GND
LCD_DG4
LCD_DG5
REG_GND
LCD_DG6
LCD_DG7
REG_GND
LCD_DR0
LCD_DR1
REG_GND
REG_GND
N.C.
N.C.
1
2
3
4
5
6
78
PANEL_NOR/REV
REG_GND
EP_2.8V
3
2
4
1
5
XX
D6001
R6045
XX
XPJ_PARK
PJ_PWR_EN
CN6007 60P
2 REG_GND
4 A_5.0V
6 A_5.0V
8
A_5.0V
10 A_5.0V
12 XPJ_RESET
14
NC
16 XPJ_PARK
18
PJ_PWR_EN
20 D_3.3V
22 REG_GND
24
LCD_DR7
26 LCD_DR6
28 REG_GND
30
LCD_DR5
32 LCD_DR4
34 REG_GND
36
LCD_DR3
38 LCD_DR2
40 REG_GND
42
LCD_DG4
44 LCD_DG5
46 REG_GND
48 LCD_DG6
50 LCD_DG7
52 REG_GND
54 LCD_DR0
56 LCD_DR1
58 REG_GND
60 REG_GND
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-29
Page 82
12345 6 7 8 9
PJ_PWR_EN
XX
XX
LCD_DB3
LCD_DB2
R6102
LCD_DB1
LCD_DB0
22k
R6106
33k
LCD_CK
CL6101
J9
G8B0F9B1F8B2E9B3E8B4D9B5D8
F/S
CPE
SN65LVDS302ZQER
LCD SERIAL INTERFACE
G9
PCLK
RECEIVER
R6104 XX
H7
IC6101
R6103
R6105
LCD_HD
LCD_VD
LCD_DATEN
J2
J7DEJ8VSH8HSH9
GND
RXEN
SWAP
H6
J1
GND_LVDS
GND_LVDS
G2
GND_LVDS
H4
GND_PLLA
E2
GND_PLLD
VDD_LVDS
VDD_LVDS
VDD_PLLA
VDD_PLLD
H5
H2
RB6101
H3
XX
F2
1
CPOL
H1
LS1
D2
LS0
C1
D0-
J6
D0+
J5
CLK-
J4
CLK+
J3
D1-
G1
D1+
F1
D2-
E1
D2+
D1
GND
G6
GND
G5
GND
G4
GND
G3
GND
F6
2
4
3
6
5
7
8
LCD_DATEN
LCD_HD
LCD_CK
LCD_DB1
LCD_DB2
LCD_DB3
LCD_DB4
LCD_DB5
LCD_DB6
LCD_DB7
LCD_DG0
LCD_DG1
LCD_DG2
LCD_DG3
LCD_DG4
LCD_DG5
LCD_DG6
LCD_DG7
LCD_DR1
LCD_DR2
LCD_DR3
LCD_DR4
LCD_DR5
LCD_DR6
LCD_DR7
LCD_DATEN
LCD_VD
LCD_HD
LCD_CK
LCD_DB0
LCD_DB1
LCD_DB2
LCD_DB3
LCD_DB4
LCD_DB5
LCD_DB6
LCD_DB7
LCD_DG0
LCD_DG1
LCD_DG2
LCD_DG3
LCD_DG4
LCD_DG5
LCD_DG6
LCD_DG7
LCD_DR0
LCD_DR1
LCD_DR2
LCD_DR3
LCD_DR4
LCD_DR5
LCD_DR6
LCD_DR7
A
LCD_DB5
LCD_DB4
CL6102
CL6103
CL6104
CL6105
CL6106
CL6108
CL6107
CL6109
D2+
D2-
D1+
D1-
CLK+
CLK-
D0+
D0-
LCD_DB6
LCD_DB7
LCD_DG0
LCD_DG1
LCD_DG2
LCD_DG3
LCD_DG4
LCD_DG5
LCD_DG6
LCD_DG7
LCD_DR0
LCD_DR1
LCD_DR2
LCD_DR3
LCD_DR4
LCD_DR5
LCD_DR6
LCD_DR7
R6101 XX
B6
C9
B7
C8
G0
B9
G1
B8
G2
A8
G3
B7
G4
A7
G5
B6
G6
A6
G7
B5
GND
A9
R0
A5
R1
B4
R2
A4
R3
B3
R4
A3
R5
B2
R6
A2
R7
B1
GND
A1
VDDC4VDDC6VDDD7VDDE7VDDF7VDDG7VDDC5GNDC7GNDD3GNDD4GNDD5GNDD6GNDE3GNDE4GNDE5GNDE6GNDF3GNDF4GNDF5GND
C2
C6101
C6102
XX
0.1u
D2+
D2-
B
D1+
D1-
CLK+
CLK-
D0+
D0-
C
A_1.8V
REG_GND
A
B
C
D
GPS Model
GPS_UART_CTS
GPS_UART_RXD
GPS_UART_RTS
GPS_UART_TXD
REG_GND
XGPS_RST
D_3.3V
C6107
C6108
C6109
18p
C6110
18p
18p
18p
CN6101 8P
1 SO0/RTS_1
2 SCK0/TX0_1
3 XSCS0/CTS_1
4 SIN0/RX0_1
5 REG_GND
6 D_2.8V
7 D_3.3V
8 XGPS_RST
GP-037
CN9201
(PAGE 6-34)
Through the
Flexible Flat Cable
(FFC-254)
E
R6116 XX
D_3.3V
F
R6115 XX
REG_GND
C6105
3
4
VDD
C6106
IC6102
2.8V REG
MM3404A28URE
1u
PD-465 BOARD (2/2)
DESERIALIZER
XX MARK: NO MOUNT
1u
D_3.3V
GND Vout
1CE2
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-30
Page 83
12345 6 7 8 9
A
FB8502
PJ_SYSPWR
C8507 0.1u
FB8501
FB8504
C8508 330pC8503 0.1u
C8509 330pC8504 0.1u
XX
DPP_RESETZ
PARKZ
XX
VFLASH
C8512 1u
POWER_EN
PDATA23
PDATA22
PDATA21
PDATA20
PDATA19
PDATA18
PDATA12
PDATA13
PDATA14
PDATA15
PDATA16
PDATA17
REG_GND
DMD_D1
DMD_D2
DMD_D3
DMD_D4
DMD_D5
DMD_D7
DMD_D6
DMD_D0
DMD_STRB
C8513 1u C8514 330p
PJ_SYSPWR
VFLASH
C8501 330p C8510 10UC8505 1u
B
C
D
DMD_VBIAS
DMD_VRST
P1P8V
REG_GND
2 REG_GND
4 SYS_PWR
6 SYS_PWR
SYS_PWR
8
10 SYS_PWR
12 XPJ_RESET
14 N.C.(INTFPWR)
16 XPJ_PARK
18 PJ_PWR_EN
20 VFLASH
22 REG_GND
24 LCD_DR7
26 LCD_DR6
28 REG_GND
30 LCD_DR5
32 LCD_DR4
34 REG_GND
36 LCD_DR3
38 LCD_DR2
40 REG_GND
42 LCD_DG4
44 LCD_DG5
46 REG_GND
48 LCD_DG6
50 LCD_DG7
52 REG_GND
54 LCD_DR0
56 LCD_DR1
58 REG_GND
60 REG_GND
1 D_1.8V
3 DMD_D1
5GND
7 DMD_D2
9GND
11 DMD_D3
13 DMD_D4
15 DMD_D5
17 GND
19 DMD_D7
21 D_1.8V
23 DMD_D6
25 DMD_D0
27 GND
29 DMD_STRB
31 DMD_VBIAS
33 GND
35 GND
37 GND
39 DMD_VRST
41 D_1.8V
PD-465
(1/2)
CN6007
(PAGE 6-29)
CN8503
FP-1582
FLEXIBLE
CN5505
(PAGE 6-36)
CN8501 42P
IC8503
RT8035GQW
POWER CONTROL
60P
1REG_GND
3I2C_SDA_PJ
5I2C_SCK_PJ
7PJ_TEMP_AD
9LCD_DATEN
11REG_GND
13LCD_VD
15LCD_HD
17REG_GND
19LCD_CK
21REG_GND
C8515 XX
23LCD_DB0
25LCD_DB1
27REG_GND
29LCD_DB2
31LCD_DB3
33REG_GND
35LCD_DB4
37LCD_DB5
39REG_GND
41LCD_DB6
43LCD_DB7
45REG_GND
47LCD_DG3
49LCD_DG2
51REG_GND
53LCD_DG1
55LCD_DG0
57REG_GND
59REG_GND
2D_1.8V
4DMD_D9
C8536
6GND
1u
8DMD_D8
10GND
12DMD_D11
14DMD_D10
16GND
CL8503
18DMD_DCLK
20DMD_LOADB
22D_1.8V
24DMD_SCTRL
C8537
26GND
XX
28DMD_BUS
30DMD_VOFS
32DMD_SAC_BUS
34GND
36DMD_OEZ
C8538
38GND
0.1u
40TEST
42D_1.8V
R8514 XX
SDA_2601
SCL_2601
PJ_TEMP_AD
DATEN_CMD
VSYNC_WE
HSYNC_CS
PDATA0
PDATA1
PDATA2
PDATA3
PDATA4
PDATA5
PDATA6
PDATA7
PDATA11
PDATA10
PDATA9
PDATA8
DMD_D9
DMD_D8
DMD_D11
DMD_D10
DMD_DCLK
DMD_LOADB
DMD_SCTRL
DMD_BUS
DMD_SAC_BUS
DMD_OEZ
CL8502
PCLK
C8516 1u
C8517 330p
POWER_EN
FB8506
XX
C8519
0.1u
XX
C8518
10u
C8520 0.1u
P1P8V
C8521
10U
PJ_SYSPWR
C8522
330p
P1P8V
REG_GND
PJ_SYSPWR
DMD_VOFS
DMD_EN
REG_GND
PJ_SYSPWR
VFLASH
DMD_PWR_EN
REG_GND
DMD_VOFS
Note: All mounted parts are not supplied, but they are
included in PJ-104 COMPLETE BOARD.
FB8505
C8523
1u
R8501
R8502
TC7SZ07AFS
200k
100k
R8505 75k
IC8501
INVERTER
1
INA
2
GND
OUTY
3
N.C.
R8504
C8524
22p
R8506 13k
VCC
XX
L8501 2.2uH
R8518 470
R8503
200k
5
4
R8507
E
R8508
100k
1
2
3
4
5
6
10k
DMD_EN
C8525
4.7u
POWER CONTROL
FBA
VOUTA
GND
ENB
FBB
GND
IC8502
RT8522GQW
1
EN1
2
FB1
3
VIN2
4
GND
5
LX2
SS
ENA
VINA
VOUTB
VINB
GND
SW
13
GND
11
12
11
10
9
8
7
GND
VIN1
L8504 10uH
LX1
FB2
EN2
E
C8526 0.1u
10
9
8
7
6
1SS420(TL3SONY.F)
L8503 2.2uH
1SS420(TL3SONY.F)
D8501
C8527
1000p
C8528
4.7u
E
D8502
R8509 1k
C8531 0.1u
C8529
XX
C8530
22p
C8532 XX
R8510 560k
R8511
R8512
P1P0V
150k
220k
R8513
18k
FB8507
XX
C8533
10U
D8503
DZ2S100M0L
FB8508
C8534
0.1u
DMD_VRST
C8535
1u
C8539
XX
P1P0V
PJ_SYSPWR
DMD_VBIAS
A
B
C
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
LED_ANODE
RED_CATHODE
REG_GND
PJ_TEMP_AD
GRN_CATHODE
BLU_CATHODE
10P
CN8502
1 LED_ANODE
2 LED_ANODE
3 RED_CATHODE
4 RED_CATHODE
5 REG_GND
6 PJ_TEMP_AD
7GRN_CATHODE
8GRN_CATHODE
9 BLU_CATHODE
10 BLU_CATODE
PROJECTOR
UNIT (1/2)
Note: PROJECTOR UNIT is not included in
PJ-104 COMPLETE BOARD.
R8515
R8516 XX
R8517 0
E
XX
PJ-104 BOARD (1/4)
F
CONNECTORS, REGULATOR
XX MARK: NO MOUNT
6-31
Page 84
12345 6 7 8 9
REG_GND
A
B
C
D
VFLASH
P1P0V
P1P8V
DATEN_CMD
VSYNC_WE
HSYNC_CS
PDATA0
PDATA1
PDATA2
PDATA3
PDATA4
PDATA5
PDATA6
PDATA7
PDATA8
PDATA9
PDATA10
PDATA11
PDATA12
PDATA13
PDATA14
PDATA15
PDATA16
PDATA17
PDATA18
PDATA19
PDATA20
PDATA21
PDATA22
PDATA23
SCL_2601
SDA_2601
DPP_RESETZ
C8602
18p
C8603
18p
PCLK
PARKZ
2
4
X8601
16.66667MHz
13
R8605
R8606
R8608
R8610
R8613
R8614 100k
100k
XX
33
100k
R8611 100
R8612
33
1M
H15 PDM_CVS_TE
G15 DATEN_CMD
D13 PCLK
VSYNC_WE
H14
H13 HSYNC_CS
G14 PDATA_0
G13 PDATA_1
F15 PDATA_2
F14 PDATA_3
F13 PDATA_4
E15 PDATA_5
E14 PDATA_6
E13 PDATA_7
D15 PDATA_8
D14 PDATA_9
C15 PDATA_10
C14 PDATA_11
C13 PDATA_12
B15 PDATA_13
B14 PDATA_14
A15 PDATA_15
A14 PDATA_16
B13 PDATA_17
A13 PDATA_18
C12 PDATA_19
B12 PDATA_20
A12 PDATA_21
C11 PDATA_22
B11 PDATA_23
A11 LED_ENABLE
A10
SCL
C10
SDA
B10 DBIC_CSZ
J14 RESETZ
B8 PARKZ
N5 JTAGTCK
P6 JTAGTDI
N7 JTAGTMS
P8 JTAGRSTZ
R7 JTAGTDO
J15 PLL_REFCLK_O
K15 PLL_REFCLK_I
IC8605 (1/2)
DPP2601
DMD CONTROL
DMD_D7
GPIO4_INTF
TSTPT_3
IC8605 (2/2)
DPP2601
DMD CONTROL
M15DMD_D0
N14DMD_D1
M14DMD_D2
N15DMD_D3
P13DMD_D4
P14DMD_D5
P15DMD_D6
R15
R12DMD_D8
N11DMD_D9
P11DMD_D10
R11DMD_D11
N10DMD_D12
P10DMD_D13
R10DMD_D14
N13DMD_DCLK
L14DMD_SAC_CLK
L15DMD_SAC_BUS
L13DMD_DAD_BUS
K13DMD_DAD_STRB
M13DMD_DAD_OEZ
R13DMD_LOADB
R14DMD_SCTRL
P12DMD_TRC
A6CMP_OUT
P5GPIO0_CMPPWR
B7CMP_PWM
P7LEDDRV_ON
N8GPIO1_RPWM
P9GPIO2_GPWM
R8GPIO3_BPWM
N6LED_SEL_1
R6LED_SEL_0
A9HWTEST_EN
C9
B9GPIO5_INTF
R9TSTPT_7
N9TSTPT_6
C8TSTPT_5
A7TSTPT_4
B5
C7TSTPT_2
A8TSTPT_1
B6TSTPT_0
H12VDD_PLL
J13VSS_PLL
R8616
R8617
C8605
R8618
R8619
100k
33
C8606
0.01u
0.1u
100k
100k
FB8601
FB8602
DMD_D0
DMD_D1
DMD_D2
DMD_D3
DMD_D4
DMD_D5
DMD_D6
DMD_D7
DMD_D8
DMD_D9
DMD_D10
DMD_D11
DMD_DCLK
CL8604
DMD_SAC_BUS
DMD_BUS
DMD_STRB
DMD_OEZ
DMD_LOADB
DMD_SCTRL
LEDDRV_ON
LED_SEL1
LED_SEL0
MEM0_LDQS
MEM0_LDM
MEM0_DQ0
MEM0_DQ1
MEM0_DQ2
MEM0_DQ3
MEM0_DQ4
MEM0_DQ5
MEM0_DQ6
MEM0_DQ7
MEM0_UDQS
MEM0_UDM
MEM0_DQ8
MEM0_DQ9
MEM0_DQ10
MEM0_DQ11
MEM0_DQ12
MEM0_DQ13
MEM0_DQ14
MEM0_DQ15
DMD_PWR_EN
C8607 0.1u
0.1u
C8608
C8609 0.1u
C8610 0.1u
C8611 0.1u
C8612 0.1u
C8613 XX
C8614 XX
C8615 XX
C8616 XX
C8617 0.1u
C8618 1u
C8619 0.1u
C8620 0.1u
C8621 0.1u
C8622 0.1u
C8623 0.1u
C8624 0.1u
C8625 0.1u
C8626 0.1u
C8627 1u
Note: All mounted parts are not supplied, but they are
included in PJ-104 COMPLETE BOARD.
J2 MEM0_LDQS
J1 MEM0_LDM
N1 MEM0_DQ0
MEM0_DQ1
M2
M1
MEM0_DQ2
L3 MEM0_DQ3
L2 MEM0_DQ4
MEM0_DQ5
K2
L1 MEM0_DQ6
K1 MEM0_DQ7
G1 MEM0_UDQS
H1 MEM0_UDM
H2 MEM0_DQ8
G2 MEM0_DQ9
H3 MEM0_DQ10
F3 MEM0_DQ11
F1 MEM0_DQ12
E2 MEM0_DQ13
F2 MEM0_DQ14
E3 MEM0_DQ15
K14 DMD_PWR_EN
D11 VCC_INTF
VCC_INTF
E12
D6 VCC_FLSH
C4 VCC18
D8 VCC18
E4 VCC18
G3 VCC18
K3 VCC18
K12 VCC18
L4 VCC18
M5 VCC18
M9 VCC18
M12 VCC18
N4 VCC18
N12 VCC18
D5 VDD10
D9 VDD10
F4 VDD10
F12 VDD10
J4 VDD10
J12 VDD10
M6 VDD10
M8 VDD10
M11 VDD10
P1MEM0_A0
R3MEM0_A1
R1MEM0_A2
R2MEM0_A3
A1MEM0_A4
B1MEM0_A5
A2MEM0_A6
B2MEM0_A7
D2MEM0_A8
A3MEM0_A9
P2MEM0_A10
B3MEM0_A11
D3MEM0_A12
M3MEM0_BA0
P3MEM0_BA1
P4MEM0_RASZ
R4MEM0_CASZ
R5MEM0_WEZ
J3MEM0_CSZ
C1MEM0_CKE
R8620 33
D1MEM0_CLK_P
R8621 33
E1MEM0_CLK_N
R8623
A4SPICLK
R8624 33
B4SPIDIN
R8625 33
C5SPIDOUT
R8626 33
A5SPICSZ0
C6SPICSZ1
C2RESERVED
C3RESERVED
N2RESERVED
N3RESERVED
D4GND
GND
D7
D10GND
D12GND
G4GND
G12GND
H4GND
GND
K4
L12GND
M4GND
M7GND
M10GND
MEM0_A0
MEM0_A1
MEM0_A2
MEM0_A3
MEM0_A4
MEM0_A5
MEM0_A6
MEM0_A7
MEM0_A8
MEM0_A9
MEM0_A10
MEM0_A11
MEM0_A12
MEM0_BA0
MEM0_BA1
MEM0_RASZ
MEM0_CASZ
MEM0_WEZ
MEM0_CSZ
MEM0_CKE
MEM0_CLK_P
MEM0_CLK_N
33
SPICLK_INT
SPIDIN_INT
SPIDOUT_INT
SPICS_INT
DPP_RESETZ
SPICS_INT
SPIDIN_INT
SPICLK_INT
SPIDOUT_INT
REG_GND
VFLASH
SPICS_INT
SPIDIN_INT
REG_GND
VFLASH
R8627
C8628 0.1u
C8629 0.1u
100k
CN8601 8P
1 RESET
2 SPICS_INT
3 SPIDIN_INT
4 SPICLK_INT
5 SPIDOUT_INT
6GND
7N.C.
8 VFLASH
W25X40BVPY08
FLASH MEMORY
1
/CS
2
DO
3
/WP
4
GND
IC8603
A
NC
B
VCC
8
HOLD
7
CLK
6
R8628
DIO
5
9
SPICLK_INT
100k
SPIDOUT_INT
C
D
E
F
P1P8V
LED_SEL0
LED_SEL1
REG_GND
C8601
0.1u
13
15
2A1142A0
X2E
VCC
16
17
1
X1E
100k
R8602
100k
R8601
74LVC139BQ-118
LED DECODER
1A031A14X1Y0
2
IC8601
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
E
10
X2Y211X2Y112X2Y0
9
X2Y3
8
GND
X1Y1
X1Y27X1Y3
5
6
IC8602
TC7WG04FC
INVERTER
1
1A
2
3Y
3
2A
4
GND
Vcc
8
C8604 0.1u
1Y
7
3A
6
2Y
5
9
BLU_STROBE
GRN_STROBE
RED_STROBE
PJ-104 BOARD (2/4)
F
DMD CONTROL
XX MARK: NO MOUNT
6-32
Page 85
12 3 4
12 3 4
A
IC8701
A9
VDD
F9
VDD
K9
VDD
A1
VSS
F1
VSS
K1
VSS
B1
VDDQ
D1
VDDQ
A7
VDDQ
C9
VDDQ
E9
VDDQ
C1
VSSQ
E1
VSSQ
A3
VSSQ
B9
VSSQ
D9
VSSQ
J8
A0
J9
A1
K7
A2
K8
A3
K2
A4
K3
A5
J1
A6
J2
A7
J3
A8
H1
A9
J7
A10/AP
H2
A11
H3
A12
H5MS2562NFR-J3MR
SDRAM
LDM
UDM
XCAS
XCS
XRAS
XWE
CKE
XCK
LDQS
UDQS
N.C.
N.C.
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
BA0
H8
BA1
H9
F8
F2
G8
H7
G9
G7
G1
CK
G2
G3
E8
E2
F3
F7
A8
B7
B8
C7
C8
D7
D8
E7
E3
D2
D3
C2
C3
B2
B3
A2
R8702
R8701 XX
30k
MEM0_BA0
MEM0_BA1
MEM0_LDM
MEM0_UDM
MEM0_CASZ
MEM0_CSZ
MEM0_RASZ
MEM0_WEZ
MEM0_CKE
MEM0_CLK_P
MEM0_CLK_N
MEM0_LDQS
MEM0_UDQS
MEM0_DQ0
MEM0_DQ1
MEM0_DQ2
MEM0_DQ3
MEM0_DQ4
MEM0_DQ5
MEM0_DQ6
MEM0_DQ7
MEM0_DQ8
MEM0_DQ9
MEM0_DQ10
MEM0_DQ11
MEM0_DQ12
MEM0_DQ13
MEM0_DQ14
MEM0_DQ15
P1P8V
REG_GND
C8710
1u
R8705 XX
C8701 0.1u
C8702
C8703 0.1u
0.1u
B
C8704 XX
C8705 XX
C8706
0.1u
C8707 XX
C8708 0.1u
R8704
XX
C
MEM0_A0
MEM0_A1
MEM0_A2
MEM0_A3
MEM0_A4
MEM0_A5
MEM0_A6
MEM0_A7
MEM0_A8
MEM0_A9
D
MEM0_A10
MEM0_A11
MEM0_A12
R8703
33
A
B
C
A
BLU_CATHODE
GRN_CATHODE
RED_CATHODE
LED_ANODE
13
14
15
16
17
18
BEN
GND
G_OUT
IC8801
R_OUT
L8801
2.2uH
PWM
5L26
E
GEN
12
VDDS
11
REN
10
9
VOUT
8
NC
7
VOUT
L2
C8803
4.7u
GRN_STROBE
BLU_STROBE
RED_STROBE
25
B_OUT
LM3549SQX/NOPB
LED DRIVE
NC2L13L14GND_SW
1
B
P1P8V
SDA_2601
SCL_2601
LEDDRV_ON
PJ_SYSPWR
FB8801
R8801 100k
R8802
XX
FAULT
19
SDA
20
SCL
21
EN
22
VDDP
23
NC
24
C
R8803
200k
REG_GND
C8801
10U
C8802
330p
Note: All mounted parts are not supplied, but they are
included in PJ-104 COMPLETE BOARD.
D
D
A
B
C
D
Note: All mounted parts are not supplied, but they are
included in PJ-104 COMPLETE BOARD.
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
PJ-104 BOARD (3/4)
SDRAM
XX MARK: NO MOUNT
E
E
E
PJ-104 BOARD (4/4)
F
F
08
6-33
LED DRIVE
XX MARK: NO MOUNT
F
Page 86
12345 6 7 8 9
L9207
9.1nH
C9246
LNA_EN
IC9203
NJG1143UA2(TE1)
L9213
C9248
0.001u
XX
RF AMP
RFOUT
4
5
6
3
VDD
VCTRL
2
GND
GND
1
RFIN
C9225
2p
C9244
C9226
0.1u
L9211
3.9nH
8p
R9202
1k
6800
B6
B7
B5
C5
C6
E3
E4
E5
D6
D5
E7
D7
VCC_LNA
RF_IN
GND_RF
DGND
VCC_BAT
DGND
DGND
AGND
VCC_SX
DGND
OSC1
GND_RF
R9201
A6
A7
LNA_OUT
A5
GND_LNA
MIX_IN
C9250
22p
A4
VCC_IF
C9237
0.01u
A3
B4
TEST1
VCC_ADC
IC9204
MT3328P/B
GPS RECEIVER
B3
C4
DGND
A2
XHRST
C3
B2
GIO0/PPS
GIO1/RXHOLD
CL9209
G1
VDD_IO
XINT0/GPO8
STANDBY/GIO7
RX0/SIN0/GIO19
RTS/SO0/GPO18
CTS/XSCS0/GIO17
TX0/SCK0/GIO16
GIO2/AOK
VDD_CORE
VDD_IO
B1
GIO6
C2
GIO5
D3
GIO4
C1
GIO3
D2
C9235
1u
D1
D4
E2
E1
F2
F1
A1
C9242
SIN0/RX0_1
SO0/RTS_1
XSCS0/CTS_1
SCK0/TX0_1
0.1u
0.1u
A
L9214
10nH
C9245
B
(GPS ANTENNA)
AT9201
VD9201
C9252
100p
XX
L9204
3.9nH
C9204
1.5p
C9206
SF9201
SAW FILTER
1
3p
2
0.1u
L9205
9.1nH
4
5
3
L9212
C9247
0.001u
XX
IC9202
NJG1143UA2(TE1)
RF AMP
RFOUT
4
VDD
VCTRL
5
GND
GND
6
RFIN
C
Note: All mounted parts and GP-037 COMPLETE BOARD are
LNA_VCC_2.8V
SF9202
SAW FILTER
C9212
1
3
2
2p
3
C9211
2p
2
1
XGPS_RST
not supplied, but they are included in GP386 ASSY.
4
5
D
A
B
C
D
RF_LDO_OUTG7RF_LDO_INE6ACDUP(VREF)F6CORE_LDO_ING6CORE_LDO_OUTG5RTCCLK/GIO13G4MS0/GPO9F5MS1/GPO10G3ECLK/GIO11F4SYNC/GIO12G2TX1/I2CC/GIO14F3RX1/I2CD/GIO15
F7
CL9203
SIN0/RX0_1
XSCS0/CTS_1
SCK0/TX0_1
SO0/RTS_1
CL9204
XX
ET9201
SIN0/RX0_1
SCK0/TX0_1
MARK
L9201 56nH
MARK
L9202
56nH
C9238
0.01u
CL9205
CL9206
C9239
0.01u
C9205
C9241
C9240
0.01u
X9201
16.368MHz
0.01u
L9206
MARK
1
2
VIN
3
ON_OFF
VOUT
VSS
4
IC9201
2.8V REG
S-1323B28PF-N8NTFG
1u
C9209
C9249
1u
0.001u
56nH
PD-465
(2/2)
CN6101
(PAGE 6-30)
Through the
Flexible Flat Cable
(FFC-254)
8XGPS_RST
7D_3.3V
6D_2.8V
E
CN9201 8P
5GPS_GND
4GPS_UART_TXD
3GPS_UART_RTS
2GPS_UART_RXD
1GPS_UART_CTS
C9253XXC9254XXC9255XXC9256
CL9201
CL9202
F
C9243
0.1u
GP-037 BOARD
C9228
C9230
0.1u
1u
C9231
C9232
1u
1u
CL9210
E
F
(GPS Model)
GPS
XX MARK: NO MOUNT
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-34
Page 87
12345 6 7 8 9
A
VC-658
(1/10)
CN1005
(PAGE 6-9)
VC-658
(1/10)
CN1006
(PAGE 6-9)
B
@CirP
33
@CirP
32
SP_L-
31
SP_L+
30
XBB_RST
REG_GND
28
29
AV_SCK
PJ_TEMP_AD
26
27
D_1.8V
25
AV_SO
24
XPJ_PARK
XCS_LCD
22
23
TP_X
21
TP_Y
20
BL_L
19
GPS_UART_RTS
BL_H
17
18
MT/A_5.0V
TP_SEL1
GPS_UART_CTS
14
15
16
MT/A_5.0V
MT/A_5.0V
12
13
REG_GND
REG_GND
10
11
GPS_UART_TXD
REG_GND
8
9
REG_GND
D_3.3V
GPS_UART_RXD
5
6
7
I2C_SCK
PJ_PWR_EN
3
4
REG_GND
REG_GND
1
2
LND002 33P
REG_GND
32
33
31
LND001 33P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
REG_GND
REG_GND
D0-
@CirP
D0+
REG_GND
CLK-
@CirP
CLK+
REG_GND
REG_GND
REG_GND
D1-
@CirP
D1+
REG_GND
D2-
@CirP
D2+
REG_GND
REG_GND
SP_R-
SP_R+
REG_GND
REG_GND
D_2.8V
XGPS_RST
REG_GND
REG_GND
PANEL_NOR/REV
I2C_SDA
XPJ_RESET
C
A
B
C
D
123456789
LND003
SP_L-
SP_L+
REG_GND
61P
XBB_RST
PJ_TEMP_AD
AV_SCK
A_1.8V
101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960
AV_SO
XCS_LCD
XPJ_PARK
TP_X
TP_Y
BL_L
BL_H
GPS_UART_RTS
A_5.0V
TP_SEL1
GPS_UART_CTS
A_5.0V
A_5.0V
REG_GND
REG_GND
REG_GND
GPS_UART_TXD
D_3.3V
REG_GND
GPS_UART_RXD
I2C_SCK
PJ_PWR_EN
REG_GND
XPJ_RESET
I2C_SDA
PANEL_NOR/REV
REG_GND
REG_GND
D_2.8V
XGPS_RST
REG_GND
REG_GND
SP_R+
SP_R-
REG_GND
REG_GND
D2-
N.C
D2+
REG_GND
D1-
N.C
D1+
REG_GND
REG_GND
CLK+
REG_GND
N.C
CLK-
D0+
REG_GND
61
D0-
N.C
REG_GND
E
PD-465
(1/2)
CN6001
(PAGE 6-29)
F
FP-1519 FLEXIBLE BOARD
D
E
F
VC-PD CONNECTION
(PRINTED WIRING BOARD is omitted.)
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-35
Page 88
12345 6 7 8 9
A
CN5505 42P
DMD_D1
DMD_D2
B
DMD_D3
DMD_D4
DMD_D5
DMD_D7
DMD_D6
DMD_D0
DMD_STRB
DMD_VBIAS
C
DMD_VRST
P1P8V
REG_GND
1 D_1.8V
3 DMD_D1
5GND
7 DMD_D2
9GND
11 DMD_D3
13 DMD_D4
15 DMD_D5
17 GND
19 DMD_D7
21 D_1.8V
23 DMD_D6
25 DMD_D0
27 GND
29 DMD_STRB
31 DMD_VBIAS
33 GND
35 GND
37 GND
39 DMD_VRST
41 D_1.8V
2D_1.8V
4DMD_D9
6GND
8DM_D8
10GND
12DMD_D11
14DMD_D10
16GND
18DMD_DCLK
20DMD_LOADB
22D_1.8V
24DMD_SCTRL
26GND
28DMD_BUS
30DMD_VOFS
32DMD_SAC_BUS
34GND
36DMD_OEZ
38GND
40TEST
42D_1.8V
46
45
44
43
DMD_D9
DMD_D8
DMD_D11
DMD_D10
DMD_DCLK
DMD_LOADB
DMD_SCTRL
DMD_BUS
DMD_VOFS
DMD_SAC_BUS
DMD_OEZ
TEST
DMD_D1
DMD_D2
DMD_D3
DMD_D4
DMD_D5
DMD_D7
DMD_D6
DMD_D0
DMD_STRB
DMD_VBIAS
DMD_VRST
P1P8V
C001 0.1u
REG_GND
CN5503 42P
1 D_1.8V
3 DMD_D1
5GND
7 DMD_D2
9GND
11 DMD_D3
13 DMD_D4
15 DMD_D5
17 GND
19 DMD_D7
21 D_1.8V
23 DMD_D6
25 DMD_D0
27 GND
29 DMD_STRB
31 DMD_VBIAS
33 GND
35 GND
37 GND
39 DMD_VRST
41 D_1.8V
43
2D_1.8V
4DMD_D9
6GND
8DM_D8
10GND
12DMD_D11
14DMD_D10
16GND
18DMD_DCLK
20DMD_LOADB
22D_1.8V
24DMD_SCTRL
26GND
28DMD_BUS
30DMD_VOFS
32DMD_SAC_BUS
34GND
36DMD_OEZ
38GND
40TEST
42D_1.8V
46
45
44
DMD_D9
DMD_D8
DMD_D11
DMD_D10
DMD_DCLK
DMD_LOADB
DMD_SCTRL
DMD_BUS
DMD_VOFS
DMD_SAC_BUS
DMD_OEZ
TEST
A
B
C
PJ-104
(1/4)
CN8501
(PAGE 6-31)
D
Note: All mounted parts are not supplied, but they are included
in FP-1582 FLEXIBLE COMPLETE BOARD.
Note: PROJECTOR UNIT is not included in
FP-1582 FLEXIBLE COMPLETE BOARD.
E
PROJECTOR
UNIT (2/2)
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-36
FP-1582 FLEXIBLE BOARD
PJ-PROJECTOR CONNECTION
F
Page 89
12 3 4
LND001
61P
J_5.0V
1
J_5.0V
2
J_5.0V
3
J_5.0V
D_1.8V
I2C_SCK
I2C_SDA
AV_SCK
AV_SO
LCD_B_7
LCD_B_6
LCD_B_5
LCD_B_4
LCD_B_3
LCD_B_2
LCD_B_1
LCD_B_0
A_2.8V
MCK_CN
BCK_CN
SDO
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
A
J_5.0V_GND
J_5.0V_GND
J_5.0V_GND
J_5.0V_GND
XSTRB_FULL
STROBE_ON
XCS_EVF
B
REG_GND
REG_GND
XPANEL_EVF_PS
C
VC-658
(1/10)
CN1003
(PAGE 6-9)
D
E
LCD_XVD
LCD_XHD
REG_GND
EVF_CLK_OUT
REG_GND
XBB_RST
XEVF_SW
EVER_3.0V
MIC_PWR_ON
MIC_JACK_IN
HP_JACK_IN
AUDIO_GND
SHOE_MIC_FL
SHOE_MIC_FR
AUDIO_GND
BATT_LI_3V
REG_GND
SDI1_MAG
SDI0_SPDIF_IN_MAG
LRCK_OUT
XCS_IC_2801
XSYS_RST
LANC_DC
JACK_AD
LANC_SIG
FR_XRESET
REG_GND
DAC_IOUT_PB
DAC_IOUT_Y
REG_GND
J_5.0V
61
60
J_5.0V
59
J_5.0V
58
J_5.0V
57
J_5.0V_GND
56
J_5.0V_GND
55
J_5.0V_GND
54
J_5.0V_GND
53
D_1.8V
52
XSTRB_FULL
51
STROBE_ON
50
I2C_SCK
I2C_SDA
49
48
XCS_EVF
47
AV_SCK
46
AV_SO
45
REG_GND
44
LCD_B_7
43
LCD_B_6
42
LCD_B_5
41
LCD_B_4
LCD_B_3
40
LCD_B_2
39
LCD_B_1
38
37
LCD_B_0
36
REG_GND
35
XPANEL_EVF_PS
LCD_XVD
34
33
LCD_XHD
32
REG_GND
31
EVF_CLK_OUT
REG_GND
30
29
XBB_RST
28
XEVF_SW
27
EVER_3.0V
26
MIC_PWR_ON
25
MIC_JACK_IN
24
HP_JACK_IN
23
AUDIO_GND
22
SHOE_MIC_FL
21
SHOE_MIC_FR
AUDIO_GND
20
19
BATT_LI_3V
18
A_2.8V
17
REG_GND
16
SDO
SDI1_MAG
15
SDI0_SPDIF_IN_MAG
14
13
MCK_INOUT
12
LRCK_OUT
11
BCK_OUT
10
XCS_IC_2801
9
XSYS_RST
8
LANC_DC
JACK_AD
7
6
LANC_SIG
5
FR_XRESET
4
REG_GND
3
DAC_IOUT_PB
DAC_IOUT_Y
2
REG_GND
1
LND002
A
B
A
B
C
C
RH-014
(4/5)
CN7001
(PAGE 6-24)
08
D
A
E
B
61P
12 3 4
LD-297
(1/5)
CN4004
(PAGE 6-3)
SHUTTER_XA
SHUTTER_XA
SHUTTER_A
SHUTTER_A
FR_GND
IR_LED_ON
SIRCS_SIG
D_2.8V
XTALLY_LED
KEY_AD3
DIAL_B
DIAL_A
LND00112P
1
2
3
4
5
6
7
8
9
10
11
12
LND002 12P
SHUTTER_XA
12
SHUTTER_XA
11
10
SHUTTER_A
9
SHUTTER_A
8
REG_GND
7
IR_LED_ON
6
SIRCS_SIG
D_2.8V
5
4
XTALLY_LED
3
KEY_AD3
DIAL_B
2
DIAL_A
1
FR-319
CN9601
(PAGE 6-26)
FP-1518 FLEXIBLE BOARD
LD-FR CONNECTION
(PRINTED WIRING BOARD is omitted.)
12 3 4
HOT SHOE is not included in
Note:
FP-1523 FLEXIBLE BOARD.
LND002 16P
1
SHOE_GND
2
SHOE_MIC_FR
3
SHOE_MIC_FL
4
MIC_GND
5
NC
6
NC
7
HOTSHOE_ID1
8
SHOE_UNREG
9
SHOE_UNREG
10
HOTSHOE_ID2
11
EXT_STROBE_ON
12
LANC_SIG
13
NC
14
NC
15
NC
16
SHOE_GND
HOT
SHOE
HN-003
CN1101
(PAGE 6-38)
SHOE_GND
SHOE_MIC_FR
SHOE_MIC_FL
MIC_GND
HOTSHOE_ID1
SHOE_UNREG
SHOE_UNREG
HOTSHOE_ID2
EXT_STROBE_ON
LANC_SIG
NC(SHOE_CONT)
SHOE_GND
LD-297
(1/5)
CN4005
(PAGE 6-3)
SHOE_GND
LND00112P
1
2
3
4
5
6
7
8
9
10
11
12
SHOE_GND
A
B
C
A
B
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
FP-1522 FLEXIBLE BOARD
VC-RH CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
C
FP-1523 FLEXIBLE BOARD
C
HOT SHOE
(PRINTED WIRING BOARD is omitted.)
08
6-37
Page 90
12345 6 7 8 9
VDR102
A
ENCAPSULATED
FP-1523
FLEXIBLE
HOT SHOE
(PAGE 6-37)
CABLE
CN11018P
MIC_GND
B
Note: CONTROL SWITCH BLOCK (AU91000) and
ENCAPSULATED CABLE are not
included in HN-003 COMPLETE BOARD.
C
XX
8SHUE_GND
7CH1
6
5CH2
4ID2
VDR103
3ID1
XX
2UNREG
1NC
22k
R1101
22k
R1102
VDR101
XX
REG_GND
REG_GND
RN2104MFV(TL3S
VDR106
XX
Q1103
1k
R1154
C1128
2.2u
REC_CH_SELECT
CH1_ATT_0dB
CH1_ATT_20dB
CH1_AUTO/MAN
INPUT1_LINE
INPUT1_MIC
AUDIO_LEVEL_CH1
D4.6V_CH1
CH2_AUTO/MAN
CH2_ATT_20dB
CH2_ATT_0dB
AUDIO_LEVEL_CH2
D4.6V_CH2
INPUT2_MIC
INPUT2_LINE
LOW_CUT1
LOW_CUT2
CONTROL
SWITCH BLOCK
(AU91000)
Q1104
RN2104MFV(TL3S
XLR_UNREG
CN110220P
1
GND
2
3
4
5
6
7
8
9
10
11
12
13
GND
14
15
16
17
18
GND
19
20
1k
R1157
C1129
2.2u
R1106
R1105
100
100k
C1101
10u
C1102
10u
R1103
R1104
100k
100
REC_CH_SEL
ATT_1_OFF
ATT_1
CH1_AUTO
XLR_MIC/LINE_1
XLR_PWR_ON_1
LEVEL_VOL_CH1
AU_AD
CH2_AUTO
ATT_2
ATT_2_OFF
LEVEL_VOL_CH2
XLR_PWR_ON_2
XLR_MIC/LINE_2
LOWCUT_1_OFF
LOWCUT_2_OFF
AU_+4V
ATT_2
Q1103, Q1104
ATTENUATOR
ATT_1
SWITCH
AUDIO_GND
AUDIO_GND
AUDIO_GND
XLR_UNREG
R1001
56
RB1003
1
3
5
C1001
7
4.7u
REG_GND
34
Vin
Vout
100k
2
IC1002
4.0V REG
4
Vth:0.6V/1.6V
6
8
NJM2878F4-46(TE2)
GND
CONTROL
12
0.47u
C1003
AUDIO_GND
Q1001, Q1002
SWITCHING
Q1001
R1008
1
XC9103D093MR
DC/DC CONVERTER
AU_+4V
RB1002
100k
2
1
4
3
6
5
7
8
R1003
XX
C1005
0.1u
0.22u
C1004
L1001
MCH5837-TL-E
33uH
IC1003
1
FB
2
VDD
3
CE
S
C1006
10u
EXT
5
4
GND
5
1
2
C1007
0.22u
C1009
0.001u
C1008
4
4.7u
3300
R1010
3
100
R1011
C1010
0.022u
4
1u
RB48SKTK
C1011
D1002
23
1
TK11160CSCL-G
C1014
4.7u
RB1004
100k
2
1
4
3
6
5
7
8
R1013
120k
IC1004
6.0V REG
123
Q1002
2SC6026MFV(TL3S
R1002
470
XX
R1015
C1002
R1014
C1012
0.022u
4.7u
12k
45
C1016
10u
C1015
1u
AU_+4V
AU_+9V
C1013
2.2u
AUDIO_GND
AU_-9V
AU_+6V
AUDIO_GND
A
B
C
SIGN100596
XLR_MIC/LINE_2
XLR_MIC/LINE_1
XLR_PWR_ON_2
XLR_PWR_ON_1
AU_+4V
AU_+9V
Q1101
RN2104MFV(TL3S
Q1102
R1149 15k
R1150 15k
RN2104MFV(TL3S
CN110324P
1XATT_2
XATT_1
2
AUDIO_GND
AUDIO_GND
XLR_MIC/LINE_1
XLR_PWR_ON_2
XLR_PWR_ON_1
REG_GND
AU_MIC_+2
AU_MIC_-2
AUDIO_GND
3XLR_MIC/LINE_2
4
5
6
AU_+6V
7
8REG_GND
9
XLR_UNREG
10XLR_UNREG
11XLR_UNREG
AU_-9V
12
13AUDIO_GND
14AU_MIC_+1
15AU_MIC_-1
16AUDIO_GND
17AU_LINE_1
18AUDIO_GND
19AUDUO_GND
20
21
22
23AU_LINE_2
24AUDIO_GND
D
XL-013
CN2201
(PAGE 6-39)
Through the
FLEXIBLE Flat Cable
(FFC-116)
LND103
E
CHASSIS_GND
CHASSIS_GND
LND104
LND101
CHASSIS_GND
CHASSIS_GND
LND102
R1112
XX
R1108
XX
SIGN100595
AU_+6V
AU_-9V
AUDIO_GND
AUDIO_GND
Q1101, Q1102
POWER SWITCH
R1107
XX
C1109
10u
C1121
RB1001
22u
22k
4.7u
2
1
C1117
4
3
6
5
7
8
C111822u
C111922u
C1120
4.7u
1
EXT_INPUT1
2
C1103
0.22u
C1104
0.22u
10u
C1105
C1106
0.22u
C1107
0.22u
10u
C1108
22u
C1110
22u
C1111
C1114
C1112
0.1u
C1113
33k
0.1u
R1109
EXT_INPUT2
3
BIN1+
4
BIN1-
5
MICIN1
6
LINEIN1
7
BIN2+
BIN2-
8
MICIN2
9
LINEIN2
10
AVCC
11
AVREF
12
22u
C1115
AGND
13
CH2_SEL_OUT
14
4.7u
C1116
15
RMS2C
16
17
VOL2C
22u
DETCOM1
18
R1110
DETCOM2
19
10M
LIMITER_C1
20
LIMITER_C2
21
R1111
SP_ALC_LEVEL
10M
22
AGND
23
SP_GA_VREF
24
SP_LIMIT_C
25
4700
R1114
3k
R1115
1u
4.7u
C1122
C1123
VOL1C
RMS1C
VOL1_IN
CH1_SEL_OUT
SP_LIMIT_OUT
SP_GA_OUT
SP_GA_IN
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
SPAMP_IN
SP_O+
VOL1OUT
ADIF_PIN1
SP_GND
ADIF_NIN1
DVDD_SP
ADIF_OUT1
SP_O-
ADVREF
SP_VREF
C1124 4.7u
FCN
ADIF_OUT2
ADIF_NIN2
FCP
R1117
C1126
4700
1u
ADIF_PIN2
R2A15219FP
MIC AMP
PVSS
XX
C1127
AUDIO_GND
RB1005
767778798081828384858687888990919293949596979899100
LINE_MIXOUT_L
LINE_MUTE_DRIVE
HP_IN_L
EVR_OUT_L
LINE_MIXOUT_R
CH2_ATTOUT
CH2_GAOUT
CH1_GAOUT
CH1_ATTOUT
EXT_CH3_IN
EXT_CH4_IN
CH4_ATTOUT
CH4_GAOUTVOL2_IN
CH3_GAOUT
CH3_ATTOUT
MON_MIX_OUT
MON_GAIN
MON_GAOUT
MIX_OUT_R
MIX_OUT_L
EVR_OUT_R
DAIF_CH1
DAIF_CH2
CH2_GAIN
CH1_GAIN
DAIF_CH3
DAIF_CH4
CH4_GAIN
CH3_GAIN
EVR_IN_R
EVR_IN_L
4700
2
1
XCS_AU
4
3
6
5
SCK_AU
7
8
DATA_AU
XCS_AU
REC_CH_SEL
CH1_AUTO
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CH2_AUTO
R1151
10k
C1017
1u
L1003
XLR_MIC/LINE_1
XLR_MIC/LINE_2
ATT_2_OFF
10uH
AU_+4V
IC1001
UPD78F0501AMC
MPU
ANI1
1
ANI0
2
P01
3
P00
4
P120
5
RESET
6
FLMD0
7
OCD0B
8
OCD0A
9
REGC
10
Vss
11
Vdd
12
P60
13
P61
14
P33
15
LEVEL_VOL_CH2
30
ANI2
29
ANI3
LEVEL_VOL_CH1
28
AVss
27
AVref
26
SCK
25
SI
24
SO
23
Tx
22
Rx
21
P15
20
P16
19
P17
18
P30
17
OCD1A
16
P32
R1126
10k
C1018
1u
ATT_2
ATT_1
LOWCUT_1_OFF
LOWCUT_2_OFF
ATT_1_OFF
R1019
1
AU_+4V
R1125
AU_AD
SCK_AU
DATA_AU
10k
CN1001 8P
1GND
2SI
3SO
4X1
5X2
6FLMD0
7 RESET
8VDD
D
E
3k
R1116
4.7u
C1125
CLK
XCS
DATA
BUSY
ADVCC
EXT_SW
DVDD_HP
HP_MUTE_C1
HP_MUTE_C2
HP_MUTE_DRIVE
HP_OUT_L
AD_GND
HP_GND
LINE_MUTE_C1
LINE_MUTE_C2
HP_OUT_R
HP_IN_R
VOL2OUT
IC1101
DVSS_HP
PGND
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-38
HN-003 BOARD
XLR
XX MARK: NO MOUNT
F
Page 91
12345 6 7 8 9
A
AU_+48V_CH1
C2209
C2201
XX
XX
50V
50V
1
SHIELD2
3
INPUT1INPUT2
3P
CN2202
LND201
CHASSIS_GND
B
A_GND
COLD2
2
HOT2
1
SHIELD1
3
COLD1
2
HOT1
S
R2204
XX
L2201
10uH
L2202
10uH
C2211
C2203
XX
XX
50V
50V
C
AU_+48V_CH2
C2205
D
XX
50V
C2207
XX
50V
6800
R2202
C2213
XX
50V
L2203
10uH
L2204
10uH
C2215
XX
50V
E
L2301
XLR_UNREG
REG_GND
4.7uH
R2302
C2302
C2301
XX
10k
XX
R2303
680
F
6800
6800
R2213
R2201
R2209
470k
6800
R2216
R2212
470k
C2304
IC2301
TK11840LTL-G
FB
8
OSC
7
GND
6
OUT
5
1
EaIn
2
SCP
3
VCC
4
BR_CTL
DC/DC CONVERTER
C2303
0.1u
Note: IC2301 is not supplied, but this is included in XL013 COMPLETE BOARD.
A
Q2201, Q2202
MIC SWITCH
C2217
1u
50V
C2218
1u
50V
C2221
1u
50V
C2222
1u
50V
C2224
1u
50V
C2223
1u
50V
C2219
1u
50V
C2220
1u
50V
S
XX
L2303
C2305
0.1u
0.001u
50V
R2304
1800
R2305
1SS387-TPL3
1SS387-TPL3
10k
MIC_SW_1
D2213
1SS387-TPL3
R2245
R2246
D2214
R2247
R2248
180k
D2210
MIC_SW_2
180k
180k
1SS387-TPL3
180k
R2229
Q2201
470
MCH6606-TL-E
6
3
2
4
1
R2237
R2233
R2225
100k
R2226
100k
D2209
R2227
100k
R2228
100k
L2302
33uH
S
XX
R2301
C2306
10u
1
2
3
5
4
10k
R2234
10k
R2230
470
D2215
1SS387-TPL3
1SS387-TPL3
D2211
1SS387-TPL3
D2212
1SS387-TPL3
R2231
470
R2235
10k
R2236
10k
R2232
470
Q2302
CPH5870-TL-E
D2216
2
MCH6606-TL-E
MCH6606-TL-E
2
2
MCH6606-TL-E
Q2203, Q2204
MIC SWITCH
10k
R2238
10k
1
4
6
3
Q2202
R2253
20k
R2254
20k
R2255
20k
R2256
20k
Q2203
6
3
4
1
R2239
10k
R2240
10k
1
4
3
6
Q2204
Q2302, Q2303
SWITCHING
C2307
1.5u
C2308
1.5u
C2309
1.5u
D2201
D2205
1SS387-TPL3
1SS387-TPL3
D2202
1SS387-TPL3
D2203
1SS387-TPL3
D2204
1SS387-TPL3
Q2303
2SC6026MFV(TL3S
27k
R2309
C2311
1.5u
C2312
1.5u
C2313
1.5u
GND2+
52-62O7
1SS387-TPL3
R2249
470
R2250
470
D2206
1SS387-TPL3
D2207
R2252
R2251
470
D2208
1SS387-TPL3
R2257
R2261
15k
3900
C2225
0.001u
50V
R2262
3900
8200
R2258
R2279
10
R2280
10
RN1104MFV(TL3S
R2285
10k
C2227
R2286
10u
10k
C2228
10u
R2263
3900
C2226
0.001u
50V
R2264
3900
Q2304-Q2307
+48V SWITCH
Q2305
2SA811A-T1C17
R2312
47k
R2316
R2313
220k
Q2304
R2269
10k
R2270
10k
11O21-31+4
IC2203
LINE AMP
VCC
NJM2732RB1(TE2)
8
R2266
10k
R2267
10k
470
R2259
15k
R2260
8200
XLR_PWR_ON_1
XLR_PWR_ON_2
5
R2241
220k
R2242
220k
5
5
R2243
220k
R2244
220k
5
R2306
680k
R2310
100k
50V
R2307
240k
C2310
0.0047u
R2308
10k
567V+8
V-
R2287
10k
R2288
10k
567V+8
V-
47k
R2317
220k
C2229
4.7u
R2265
2SA811A-T1C17
RN1104MFV(TL3S
Q2307
Q2306
R2271
R2268
330
1234
330
1234
R2275
AU_+48V_CH1
AU_+48V_CH2
2700
R2272
2700
IC2201
NJM2737RB1(TE2)
R2273
330
R2274
2700
IC2202
NJM2737RB1(TE2)
MIC AMP
MIC AMP
R2276
2700
R2281
10
2
6
1
5600
R2277
4
3
5
Q2205
MCH6616-TL-E
R2282
10
R2283
10
2
6
1
5600
4
R2278
3
5
Q2206
MCH6616-TL-E
330
R2284
10
A_GND
Q2205, Q2208
ATTENUATOR
R2292
100k
1
R2289
10k
C2230
4.7u
AU_+6V
AU_LINE_2
3
Q2208
RN1104MFV(TL3S
2
ATT_1
A_GND
AU_MIC_-1
AU_MIC_+1
A_GND
AU_+6V
B
C
AU_LINE_1
AU_+6V
AU_+6V
AU_MIC_-2
AU_MIC_+2
R2291
R2290
10k
Q2206, Q2207
ATTENUATOR
100k
C2231
4.7u
1
3
Q2207
RN1104MFV(TL3S
2
A_GND
ATT_2
A_GND
MIC_SW_1
AU_-9V
AU_+6V
MIC_SW_2
AU_-9V
XL-013 BOARD
XLR CONNECTORS
XX MARK: NO MOUNT
Q2331
RN2104MFV(TL3S
Q2335
RN1104MFV(TL3S
R2331
470k
Q2332
RN2104MFV(TL3S
Q2336
RN1104MFV(TL3S
R2332
470k
AU_-9V
ATT_2
ATT_1
XLR_PWR_ON_2
XLR_PWR_ON_1
AU_+6V
REG_GND
XLR_UNREG
AU_-9V
AU_MIC_+1
AU_MIC_-1
AU_LINE_1
AU_MIC_+2
AU_MIC_-2
AU_LINE_2
Q2331, Q2332,
Q2335, Q2336
MIC CONTROL
A_GND
A_GND
CN2201
24 ATT_2
23 ATT_1
22 XLR_MIC/LINE_2
21 XLR_MIC/LINE_1
20 XLR_PWR_ON_2
19 XLR_PWR_ON_1
18 AU_+6V
17 REG_GND
16 REG_GND
15 XLR_UNREG
14 XLR_UNREG
13 AU_-9V
12 A_GND
11 AU_MIC_+1
10 AU_MIC_-1
9A_GND
8AU_LINE_1
7A_GND
6A_GND
5AU_MIC_+2
4AU_MIC_-2
3A_GND
U_LINE_2
2A
1A
_GND
SWITCH
24P
HN-003
CN1103
(PAGE 6-38)
Through the
FLEXIBLE Flat Cable
(FFC-116)
D
E
F
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-39
Page 92
6-2. PRINTED WIRING BOARDS
CM-121 BOARD (SIDE A)
L1
IC6701
D9E9F9G9H9J9K9L9
L10
D10E10F10G10H10J10K10
A1
C1D1E1F1G1H1J1K1
B1
B2C2D2E2F2G2H2J2K2L2
A2
A3B3C3D3E3F3G3H3J3K3L3
A4B4C4D4H4J4K4L4
A5B5C5D5H5J5K5L5
A6B6C6D6H6J6K6L6
A7B7C7D7H7J7K7L7
A8B8C8D8E8F8G8H8J8K8L8
A9B9C9
B10C10
A10
CM-121 BOARD (SIDE B)
4
R6744
C6732
C6701
R6702
R6769
C6711
C6712
R6742
C6738
R6770
R6793
R6706
R6741
C6702
2
C6703
C6729
1
3
IC6706
C6737
R6768
R6701
R6704
C6707
C6705
C6717
C6706
C6728
34
2
1
IC6703
LF6701LF6702LF6703LF6704LF6705LF6706LF6707LF6708LF6709LF6710LF6711
1234123412341234123412341234123412341234123
R6745
C6735
C6724
C6725
C6726
R6710
R6711
R6712
R6737
R6746
C6733
3
4
IC6705
2
1
C6734
R6747
51
R6767
C6714
R6738
C6713
C6718
R6707
34
2
CN6701
IC6704
R6739
C6727
R6705
C6710
R6703
C6704
B2
B1
A2
A1
C6731
R6743
C6736
C6715
C6716
C6720
C6708
C6719
C6709
C6721
R6708
R6709
C6722
R6714
C6723
R6713
IC6702
1
R6740
C6730
4
250
1
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
08
1-882-498-
11
Note: IC6701 and CM-121 COMPLETE BOARD are not supplied,
but they are included in CMOS BLOCK ASSY (1390)-077.
6-40
1-882-498-
11
: Uses unleaded solder.
Page 93
LD-297 BOARD (SIDE A) LD-297 BOARD (SIDE B)
1
250
IC5605IC5606
B2A2 C2
B2A2 C2
B1
C1A1B1
C1A1
C5637C5638
C5632C5633
2728
MEMORY
STICK
PRO DUO
CN8001
SD
D8001
AK
R8042
C5648
C5647
C5646
R5214
R5220
R5207
R5652
R5659
R5658
C5603
C5604
C5605
R5610
R5624
R5614
R5221
R5219
R5217
C5218
C5216
R5218
R5211
C5220
C5212
C5208
H8
G8
F8
E8
D8
C8
C5211
C5206
A8
R5222
C5204
A
C5219
16
CN4006
R5613
D4001
AK
CN4005
L5603
15
11
IC5610
610
C5649
L5601
15
11
IC5609
610
C5606
H1H2H3H4H5H6H7
G1G2G3G4G5G6G7
F1F2F3F4F5F6F7
E1E2E3E4E5E6E7
D1D2D3D4D5D6D7
C1C2C3C4C5C6C7
B2B3B4B5B6B7B8
A1A2A3A4A5A6A7
C5210
L5201
R5656
R5619
R5205
C5203
C5207
IC5201
R5655
R5618
R5206
R5203
C5209
R5208R5209
RB5201
127
R5210
C5213C5214
R5204
C5205
R5202
C5651
C5654
C5655
C5656
C5610
C5609
R5201
C5202
R5212
R5213
8
R5215
R5216
A1
B1
C1
IC5611
C5652
R5635
R5634
C5621
C5653
A2B2C2
12
IC5602
C5623
B3
C3 A3
C5616
C3A3
B3
C5612
C3A3
B3
C5624
C5625
C1
A2 B2 C2
A1
C1
B1
A2 B2 C2
A1 B1
C4002
R5622
IC5603
R5620
R5605 R5606
R5603
L5602
C5636
C5642 C5643
R5640 R5641
CL5605
CL5606
C5215
CL5607
CL5602
CL5603
3
4
1
6
Q4002
4
3
C5217
C7511
1
2
1
R5617
R5627
R5621
R5623
58
R5612
R5604
R5607
58
C5617
CL5604
C5640
IC5601
R5642
R5644
R5643
R5645
2
1
IC5202
R7508
4
R7507
3
C7512
IC7501
C5611
R5626
R5625
14
9
IC5608
C5602
R5611
R5608
14
9
IC5607
A
C5618
A7 B7 C7 D7 E7 F7 G7 H7 J7 K7
A8 B8 C8 D8 E8 F8 G8 H8 J8 K8
A9 B9 C9 D9 E9 F9 G9 H9 J9 K9
A10 B10C10D10E10F10G10H10J10K10
R5638
C5628
C5630
R5639
C5629
C5631
12 13 14
C7504
14
R5616
R5615
C5607
R5602
R5601
C5601
A4 B4 C4 D4 E4 F4 G4 H4 J4 K4
A5 B5 C5 D5 E5 F5 G5 H5 J5 K5
A6 B6 C6 D6 E6 F6 G6 H6 J6 K6
C5634 C5635
R5646 R5647
C5639
R5648 R5649
C5644 C5645
R5650 R5651
SE7501
C7502
3
4
D4002
1
5
R4001
R5629
C5622
R5628
C5620
R5630
R5637
A1 B1 C1 D1 E1 F1 G1 H1 J1 K1
A2 B2 C2 D2 E2 F2 G2 H2 J2 K2
A3 B3 C3 D3 E3 F3 G3 H3 J3 K3
C5641
C5627
C5626
CL5608
710
1516
R7509
PITCH/YAW
C7501
C7503
CL5601
CL5609
8
2
RB4001
8
2
8
2
7
1
7
1
7
RB8001 RB8002
1
R5633
C5614
C5613
R5631
C4003
R4002
C4001
R4003
R5632
C4004
R4006
R4008
R8019
R8024
R4007
C4005
R8041
63
61
60
R8029
R8030
CN4001
R8043
C8002
R8040
2
1
62
63
61
60
R8017
R8011
R8018
C8001
112
CN4002
2
1
62
CN4004
51
CN4003
CL4001
R4014
R4009
R4013
129 26 30
SENSOR
08
Note: IC5602, IC5603, IC5609, IC5611 and L5601 are not supplied,
but they are included in LD-297 COMPLETE BOARD.
1-885-111-
21
08
1-885-111-
21
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
: Uses unleaded solder.
6-41
Page 94
VC-658 BOARD (SIDE A) VC-658 BOARD (SIDE B)
L4307
C4337
13
46
IC4303
CL1408
C4338
R1332
17
RB1302
GS
28
610
IC9103
11
15
R9102
12
LF9101
R9103
14
R9135
R9116
BE
Q9103
C9104
C9107
CN1006
COM443
34
R4327
F008
20
3
LF1301
124
3
LF1302
124
3
LF1303
124
3
LF1304
124
3
4
Q1403
1
6
1
Q1302
3
119
C1003
VD1002
22
6
R1342 R1343
4
D1303
8
CN9102
15
C9112
6
C
VD9101
133
2
21
CN1009
23
D1304
9
7
HDMI
(USB)
1
61
1
61
CN1010
62
63
62
63
2
CN1001
60
2
CN1002
60
1
6
COM438
R4320
R4325
COM437
R9141
R4334
C4350
C9109
IC4304
123
C4349
D1401
KA
IC9101
CL9103
CL9101
C9102
Q9102
13
C9116
R9133
CL9107
L4302
C4322
COM433
R4335
C4312
C4320
R4308
R4303
C4319
R4307
C4313
L4303
D9103
R9140
L9101
C9117
IC9102
C9113
B5
C5
D5
E5A5
A4
B4
C4
D4
E4
A3
B3
C3
D3
E3
A2
B2
C2
D2
E2
B1
C1
D1
E1A1
CL9112
45
C9110
R9136
C9111
R9120
CL9102
C9103
A1 B1 C1 D1 E1
A2 B2 C2 D2 E2
A3 B3 C3 D3 E3
A4 B4 C4 D4 E4
A5 B5 C5 D5 E5
A6 B6 C6 D6 E6
28
RB9101
17
D9104
Q1402
46
32
C4302
IC4301
C4327
C4328
C4303
R4309
D9102AK
C9118
CL9106
C9114
C9115
R9138
R9134
D1402KA
4
D9101
231
R9111
C9105
BE
FB2701
C
A8
A7
A6
A5
A4
A3
A2
A1
COM432
VD1005
VD1004
C1443
B8
B7
B6
B5
B4
B3
B2
B1
C4301
C4311
R2702
R2701
C2703
C2704
CL2705
C2705
CN1005
C8
C7
C6
C5
C4
C3
C2
C1
COM431
D8
D7
D6
D5
D3
D2
D1
CL2706
C4306
H8
G8
F8
E8
H7
G7
F7
E7
H6
G6
F6
E6
H5
F5
G5
E5
H4
G4
F4
E4
H3
G3
F3
E3
H2
G2
F2
E2
H1
G1
F1
E1
C4326
C4321
L4301
28
FB1501
RB4803
17
C1509
C1513
CL4803
CL4804
CL4805
CL9108
CL9110
CL9111
R4810
R4812
CL4818
R4819
R4816
R4813
R4811
17
28
CL9113
CL9109
BE
C2711
CL4801
RB4801
BE
C
Q1407
Q9107
C
C2707
C2708
30
31
IC2701
41
40
1
CL2704
CL2703
C2706
L2705
L2704
F001
CN1007
20
C4332
C4333
R4330
C
Q4302
B
LND101
62
2
1
C1444
CL1404CL1405
C1442
CN1003
60
61
63
A1A2A3A4A5A6A7A8A9
B1B2B3B4B5B6B7B8B9
C1C2C4C5C6C7C8
CL3303
D1D2D3D4D5D6D7D8D9
E1E2E3E4E5E6E7E8E9
F1F2F3F4F5F6F7F8F9
R3316
BE
C
Q3301
G1G2G3G4G5G6G7G8G9
H1H2H3H4H5H6H7H8H9
J1J2J3J4J5J6J7J8J9
08
127
RB1001 RB1002
8
CL3302
RB3301 RB3302
1278127
R3317
A2A3A4
A1
B1B2B3B4B5
C4329
E
C1C2C4C5C6
D1D2D3D4D5
C
E1E2E3E4E5
BE
Q4301
F2F3F4
C4317
CL4302
R4302
R3003
1
2
R3002
RB3001
7
8
R1335
C1314
C1505
CL1407
CL1402
R1321
C1313
C1303
C1320
C1318
CL1306
CL1403
C1308
CL1307
CL1308
CL1406
2
C1516
C1309
LF9103
314
C1316
C1323
R1331
L1301
C1326
C1317
R1351
R1350
127
8
C9
C1517
R1333
R3301
C3302
IC3301
8
1
C4330
C4334
C4331
A5
B6
C4309
D6
IC4302
E6
R4301
F5F1F6 A6
C3004
C1324
CL1409
C1322
R1505
C1511
R1348
C4308
R4340
C4310
C4318
C3001
R3001
D4D3D2
D1
D5C5B5A5
C4C3C2
C1
C3002
B4B3B2
B1
R3004
IC3001
A2
A3A4A1
R3005
C3003
R3006
R3007
C1327
C1325
C1315
R1472
R1473
C1321C1515
C1307
R1315
C1319
FB1301
46
13
IC1302
FB1304
C1332
C1331
X1302
43
118
F002
L4306
F004
R1421
C1501
R1422
R1423
C1526
C1507
C1527
FB1404
IC1301
C1304
C1301
12
FB1303
R1313
2 50
CN1008
1
Q4305
14
COM436
R4342
C1520
C1518
C1530
C1529
C1424
R4343
R1005
F005
F003
R4344
FB1405
C1310
CN1004
58
BE
Q4304
C
R4345
FB1403
C1428
13
Q4303
46
FB1406
C1524
C1521
C1410
C1421
C1504
C1519
C1523
C1302
COM139
COM435
R4341
A1B1C1D1E1F1G1H1J1K1L1M1N1P1R1T1U1V1W1Y1AA1AB1AC1AD1AE1AF1AG1AH1AJ1AK1AL1
A2B2C2D2E2F2G2H2J2K2L2M2N2P2R2T2U2V2W2Y2AA2AB2AC2AD2AE2AF2AG2AH2AJ2AK2AL2
A3B3C3D3E3F3G3H3J3K3L3M3N3P3R3T3U3V3W3Y3AA3AB3AC3AD3AE3AF3AG3AH3AJ3AK3AL3
A4B4C4D4AJ4AK4AL4
A5B5C5AJ5AK5AL5
A6B6C6F6G6H6J6K6L6M6N6P6R6T6U6V6W6Y6AA6AB6AC6AD6AE6AF6AJ6AK6AL6
A7B7C7F7G7H7J7K7L7M7N7P7R7T7U7V7W7Y7AA7AB7AC7AD7AE7AF7AJ7AK7AL7
A8B8C8F8G8H8J8K8L8M8N8P8R8T8U8V8W8Y8AA8AB8AC8AD8AE8AF8AJ8AK8AL8
A9B9C9F9G9H9AD9AE9AF9AJ9AK9AL9
A10B10C10F10G10H10K10L10M10N10P10R10T10U10V10W10Y10AA10AB10AD10AE10AF10AJ10AK10AL10
A11B11C11F11G11H11K11L11M11N11P11R11T11U11V11W11Y11AA11AB11AD11AE11AF11AJ11AK11AL11
A12B12C12F12G12H12K12L12M12N12P12R12T12U12V12W12Y12AA12AB12AD12AE12AF12AJ12AK12AL12
A13B13C13F13G13H13K13L13M13N13P13R13T13U13V13W13Y13AA13AB13AD13AE13AF13AJ13AK13AL13
A14B14C14F14G14H14K14L14M14N14P14R14T14U14V14W14Y14AA14AB14AD14AE14AF14AJ14AK14AL14
A15B15C15F15G15H15K15L15M15N15P15R15T15U15V15W15Y15AA15AB15AD15AE15AF15AJ15AK15AL15
A16B16C16F16G16H16K16L16M16N16P16R16T16U16V16W16Y16AA16AB16AD16AE16AF16AJ16AK16AL16
A17B17C17F17G17H17K17L17M17N17P17R17T17U17V17W17Y17AA17AB17AD17AE17AF17AJ17AK17AL17
A18B18C18F18G18H18K18L18M18N18P18R18T18U18V18W18Y18AA18AB18AD18AE18AF18AJ18AK18AL18
A19B19C19F19G19H19K19L19M19N19P19R19T19U19V19W19Y19AA19AB19AD19AE19AF19AJ19AK19AL19
A20B20C20F20G20H20K20L20M20N20P20R20T20U20V20W20Y20AA20AB20AD20AE20AF20AJ20AK20AL20
A21B21C21F21G21H21K21L21M21N21P21R21T21U21V21W21Y21AA21AB21AD21AE21AF21AJ21AK21AL21
A22B22C22F22G22H22K2L22M22N22P22R22T22U22V22W22Y22AA22AB22AD22AE22AF22AJ22AK22AL22
A23B23C23F23G23H23AD23AE23AF23AJ23AK23AL23
A24B24C24F24G24H24J24K24L24M24N24P24R24T24U24V24W24Y24AA24AB24AC24AD24AE24AF24AJ24AK24AL24
A25B25C25F25G25H25J25K25L25M25N25P25R25T25U25V25W25Y25AA25AB25AC25AD25AE25AF25AJ25AK25AL25
A26B26C26F26G26H26J26K26L26M26N26P26R26T26U26V26W26Y26AA26AB26AC26AD26AE26AF26AJ26AK26AL26
A27B27C27AJ27AK27AL27
A28B28C28AJ28AK28AL28
A29B29C29D29E29F29G29H29J29K29L29M29N29R29R29T29U29V29W29Y29AA29AB29AC29AD29AE29AF29AG29AH29AJ29AK29AL29
A30B30C30D30E30F30G30H30J30K30L30M30N30R30R30T30U30V30W30Y30AA30AB30AC30AD30AE30AF30AG30AH30AJ30AK30AL30
A31B31C31D31E31F31G31H31J31K31L31M31N31R31R31T31U31V31W31Y31AA31AB31AC31AD31AE31AF31AG31AH31AJ31AK31AL31
R1515
CN1011
16
R1003
FB1401
VD1001
C1438
R1469
C1423
C1514
C1306
C1413
C1510
C1305
C1411
R1449
C1412
R1409
R1411
R1412
C1512
C1506
C1508
C1502
R1004
D4301
D1001
F006
F007
C1441
R1460
R1467
R1468
R1455
C1439
R1454
COM133
FB1302
R1410
FB1402
1
2
RB1404
7
8
R1413
R1414
R1334
1
2
RB1402
7
8
1
2
RB1403
7
8
P
R9105
R1006
LF9102
3
C1001
C1002
D4302
12
R4347R4348
46
R4346
C4355
Q4307
13
C
Q4306
BE
1
2
RB1405
7
8
2
314
R9106
CN9101
F009
51
15
67
COM444
L4308
L4304
CL4819
A
C4801
C4806
R1001
R4818
K11
L11
K10
L10
K9
L9
K8
L8
R4815
K7
L7
K6
L6
K5
L5
K4
L4
CL4806
K3
L3
K2
L2
K1
L1
CL4802
C4802
R4806
C4804
1
2
28
RB1407
17
3
4
Q9106
1
6
D9105
C4315
R4314
C4811
C4809
R4802
COM440
C4314
COM441COM442
R4323
R4801
R4817
R4814
R4809
C4807
C4803
C9119
R4313
R4306
R4315
R4349
1
6
Q4801
4
3
COM481
R4808
Q1301
D
C9101
C9121
28
RB9102
17
R4324
C4316
R4304
C4304
C4305
C4323
C4808
A11
B11
A10
B10
A9
B9
A8
B8
A7
B7
A6
B6
C4810
A5
B5
A4
B4
A3
B3
A2
B2
A1
B1
CL4812
CL4814
CL4813
4
3
R1471
C4324
R4305
C4325
CL4815
28
RB4802
17
C11
D11
C10
D10
C9
D9
C8
C7
IC4801
C6
C5
C4
C3
D3
C2
D2
C1
D1
CL4810
CL4809
CL4807CL4808
F1401
21
20
L4305
CL4301
CL4811
CL4816
R1002
E11
F11
G11
H11
J11
E10
F10
G10
H10
J10
E9
F9
G9
H9
J9
J8
J7
J6
J5
J4
E3
F3
G3
H3
J3
E2
F2
G2
H2
J2
E1
F1
G1
H1
J1
R4807
R4803
C4805
X4801
13
Q1408
46
C2709
C2710
13
C2701
IC9105
C2702
11
10
L2701
L2702
VD1003
L2703
R9137
Q9105
58
64
15
11
IC9104
610
R9142
133
2
32
Note: IC1301 is not supplied, but this is included in
VC-658 COMPLETE BOARD (SERVICE).
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-885-107-
21
6-42
1-885-107-
21
08
: Uses unleaded solder.
Page 95
MM-102 BOARD (SIDE B)MM-102 BOARD (SIDE A)
C8205
C8204
A11
A9
A6
A4
FB8701
B13
B2
R8110
7
8
R8109
FB8702
RB8102
D14
AR1
AU3
AA14Y14W14J14 K14 L14
T10R10P10N10
T2R2P2N2M2
C8104
C8105
U10
V14U14T14R14P14N14M14
AA13Y13W13
V13U13T13R13P13N13J5M13
AA12Y12W12
V12U12T12R12P12N12M12H12
Y11
W11
Y10
AA10
W10M10H10
Y9
AA9
W9M9H9
U9
Y8
U8
U7
U6
AA8
W8
W7M7H7
Y7
AA7
W6
Y6
AA6
Y5
AA5
W5U5T5R5P5
AA4Y4W4
V3U3T3R3P3N3M3
AA3Y3W3
AA2Y2W2
V2U2
Y1W1
V1U1T1R1P1N1M1L1K1J1H1
AA1
R8113
R8112
R8101 R8102
AE14
AE1
AG13
AG2
C8701
AH11
AH9
AH6
AH4
3
4
R8111
2
1
IC8701
C8103
C8102
H14
J13 K13 L13
H13
J12 K12 L12
H11
J11
K11 AA11
J10
K10
J9
K9
M8H8
J8
K8
K7
K6
K5
K2 L2
M6H6
M5
IC8101
N5
H5
H4
H3
H2
J7
J6
J4 K4 L4
J3 K3 L3
J2
D1
R8103
R8104
R8105
R8106
R8107
R8108
FB8703
FB8704
FB8705
FB8706
FB8707
FB8708
1
1
2
7
8
RB8101
2
AV6
AV9
AV12
AV15
AV18
AV21
AU24
AR26
C8203
C8202
AJ4
AJ5
AJ6
AJ7
AJ8
AJ19
AJ20
AJ21
AJ22
AJ23
AH4
AH5
AH6
AH7
AH8
AH19
AH20
AH21
AH22
AH23
AF4
AG4
AE4
AF5
AG5
AE5
AF7
AE7 AD7
AC7 AB7
AA7Y7W7V7U7T7R7P7N7
AC8 AB8
AA8 Y8 W8 V8 U8
AC9 AB9 AA9 Y9 W9 V9 U9
AD10
AD11 AB11 AA11 Y11 W11
AB12
AD12
AB13
AD13 U13 N13
IC8201
AB14
AD14
AB15
AD15 U15 N15
AB16
AA16 Y16 W16 V16
AD16 U16 N16
AD17
AB18 AA18 Y18 W18 V18 U18 N18
AC18
AC19 AB19 AA19 Y19 W19
AD20 P20R20T20
AA20 Y20 W20 V20 U20
AC20 AB20
R8203
R8202
AG22
AG23
R8201
AF8 AE8 AD8
AF9 AE9 AD9
AF10 AE10
AF11
AE11
AE12
AF12
AE13
AF13
AF14
AE14
AF15
AE15
AF16
AE16
AE17
AF18 AE18 AD18
AF19 AE19 AD19
AF20 AE20
AF22
AE22
AF23
AE23
U11
V11
U12 N12
U14 N14
V19
U19
N4
P4
P5
R8T8
P8
P9R9T9
P10R10T10
R11
P11
P12
R12
R13
P13
R14
P14
R15
P15
R16
P16
P17
R17AF17
P18R18T18
R19
P19T19
P22
K4
M4
L4
N5
K5
M5
L5
K6
L6
K7
L7
N8
K8
L8
N9
N10
N11
N17
N19
K19
L19
N20
K20
L20
K21
L21
N22
K22
M22
L22
N23
K23P23
M23
L23
D1
B3
A6
A9
A12
A15
A18
A21
B24
D26
SSGE
QR-CODE
08
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
118
CN8101
1-884-970-
11
08
Note: IC8101 and IC8201 are not supplied, but they are
included in MM-102 COMPLETE BOARD.
6-43
1-884-970-
11
: Uses unleaded solder.
Page 96
RH-014 BOARD (SIDE A) RH-014 BOARD (SIDE B)
34
SE6401
12
C6411
R6415
GS
Q6401
D
C7010
3
C7207
RB6405
127
CN7005
122
8
RB6404
8
127
C6410
R7213
R7214
R7009
FB7005
FB7006
VDR709 VDR710
C7003
C7001
PLUG IN
POWER
2
J7001
4
13
1
2
R7003
C7005
FB7003
FB7004
C7002
C7004
R7010
(HEADPHONE)
A/V R
2
J7002
13
14
CN7002
678910
12345
11
12
FB7010
R7008
FB7011
FB7002
FB7001
13
VDR703VDR704
C7007 C7008
4
R2829
R7004
VDR705
C7006
KA
R7212
VDR721
R7201
R7203
R7206
R2606
C2604
R2603
R2601
R2602
R2604
R7204
C7205
D7201
R6405
RB2602
A7B7L7M7
IC2801
C2841
C7201
28
17
12 9
13
IC6402
16
R2805
C2807
C2820
A8B8L8M8
A9B9L9M9
C2810
A10B10L10M10
RB6401
CL2802
C2855
A11B11C11D11E11F11G11H11J11K11L11M11
CN7003
41
R2804
C2806
C2854
A12B12C12D12E12F12G12H12J12K12L12M12
CL2803
R6412
R6413
8
5
R2801
C2805
C2853
C2802
C2801
C2828 C2829
C2830
C2831
C2835
CL2801
VDR702
28
RB6402
17
18
R6401
19
IC6403
C6404
R6402
24
R6408
16
28
17
R2811
C2817
C2803
R2827
C2818
R2813
C2804
R2828
C6405
C2847
3
C2846
4
R2816
C6403
R6414
C2832
C2842
R2802
122
28
RB6403
17
13
12
7
28
RB6406RB6407
17
2
COM702
1
R7002
IC6401
COM701
R7001
C6406
61
60
CN7001
2
1
VDR706
C7202
R7207
C7208
B4
A4 E4
A3
B3
A2
B2
B1
A1
IC7201
C7204
C7209
CL7203
C2601
L2601
C2614
C2607
C2610
C2611
C2605
C2606
C2609
C2608
L2803
CL2601
R7210
C7203
C4
D4
C3
D3
E3
C2
D2
E2
C1
D1
E1
L7201
C2602
A3B3D3E3F3
A2B2C2D2E2F2
A1B1C1D1E1F1
C2615
R2605
C2603
R2814
R2815
C2815
C2836
L2804
VDR701
R7208
R7209
C7206
FB7201
C7009
CL7201
R7007
CL7202
IC2601
C2613
C2824
A1B1C1D1E1F1G1H1J1K1L1M1
C6401
C6402
C2612
C2617
C2618
28
17
C2814
L2802
C2821
C2822
A2B2C2D2E2F2G2H2J2K2L2M2
A3B3L3M3
A4B4L4M4
A5B5L5M5
A6B6L6M6
C2849
C2850
L2602
C2616
A6B6C6D6E6F6
A5B5C5D5E5F5
A4B4D4E4F4
C2823
C2833
C2834
C2837
C2852
Note: BT7001 and C7207 are not included in RH-014
08
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は，正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換し
てください。
使用済み電池は，取扱指示に従って処分してください。
COMPLETE BOARD.
CN7004
16
1-885-108-
11
Note: Replace the battery holder (BH7001) together when replacing
the lithium storage battery (BT7001) on the RH-014 board. (The
battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first and
attach new lithium battery next.
Note:
RH-014基板のリチウム蓄電池（BT7001）を交換する場合はバッ
テリホルダ（BH7001）も同時に新品に交換して下さい。（一度
使用したバッテリホルダは再使用できません。）
部品取り付 け の際は ， 先にバッテリホルダを取り付 けて からリ
チウム電池を装着して下さい。
BH7001
VDR707VDR708
4
2
RESET
S7001
1
3
08
BT7001
Note: IC6401 is not supplied, but this is
included in RH-014 COMPLETE BOARD.
1-885-108-
11
LITHIUM
BATTERY
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
: Uses unleaded solder.
6-44
Page 97
FR-319 BOARD (SIDE B)FR-319 BOARD (SIDE A)
R9603R9604
Note: Q9601 is not supplied, but this is
included in FR-319 COMPLETE BOARD.
Q9601
BCE
R9601
1
2
D9601
3
4
34
08 08
IC9601
R9602
C9601
C9602
12
R9605
D9602
1-885-113-
11
5
CN9602
1
VD9602
C9603
R9606
6
2
R9607
VD9601
C9604
C9606
C9605
CN9603
2
12
1-885-113-
1
CN9601
11
11
CK-244 BOARD (SIDE A)
VD9004
VD9003
2
4
S9003
3
LIGHT
1
08
S9004
3
1
NIGHTSHOT
2
S9001
4
POWER
4
2
VD9001
1
3
4
S9005
3
CK-244 BOARD (SIDE B)
127
RB9002
8
VD9006
2
R9011
1
R9012
VD9002
4
S9002
3
PROJECTOR
2
1
R9001
D9001
AK
R7706
C7706
C7701
R7702
R7701
C7702
R7704
R7703
C7705
R7705
R7707
C7704
VD9005
D9002
AK
4
2
MODE
S9006
1
3
CN9002
10
1617181920
IC7701
51234
987
6
10
4
1
C7707
L7701
11 12 13 14 15
C7703
3
SE7701
12
R9010
3
1
D9003
4
5
R9005
R9008
RB9001
17
28
R9002
R9004
R9006
R9003
20
C9003
R9007
C9002
CN9001
1
C9001
1-885-114-
11
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
1-885-114-
08
11
: Uses unleaded solder.
6-45
Page 98
PD-465 BOARD
R6002
1
SE6001
1
2
C6001
3
R6012
4
R6045
R6006
2
R6016 R6017
2
CN6007
CN6001
R6106
R6102
R6103
R6104
CL6101
CL6104
R6105
J9
H9
G9
C6102
J8
H8
G8
J7
H7
G7
J6
H6
G6
J5
H5
G5
J4
H4
G4
J3
H3
G3
CL6108
CL6109
J2
H2
G2
J1
H1
G1
CL6106
CL6105
CL6107
IC6101
F9
E9
D9
C9
B9
A9
59
60
F8
E8
D8
C8
B8
A8
F7
E7
D7
C7
B7
A7
F6
E6
D6
C6
B6
A6
F5
E5
D5
C5
B5
A5
F4
E4
D4
C4
B4
A4
F3
E3
D3
B3
A3
F2
E2
D2
C2
B2
A2
F1
E1
D1
C1
B1
A1
CL6103
CL6102
60
C6101
R6101
127
RB6101
8
R6115
C6105
4
1
2
3
IC6102
R6116
C6106
R6035
C6107
R6033
R6034
R6032
C6109
C6110
C6108
18
CN6101
R6037
CN6004
12
Q6002
143
6
Q6001
4
6
3
1
C6003
D6001
4
5
8
6
CN6002
1
7
1
3
C6002
1
08
CN6005
61
L6001 L6002
C6027
C6025
D6002
C6019
C6033
CL6009
CL6003
C6026
CL6008
CL6002
C6032
CL6007
CL6001
CL6006
C6024
CL6005
CL6004
C6031
C6030
1
2
C6020
C6023
C6029
C6022
C6021
R6040
61
CN6003
260
1
R6044
C6034
R6042
R6041
R6043
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
6-46
1-885-440-
11
: Uses unleaded solder.
Page 99
PJ-104 BOARD (SIDE B) PJ-104 BOARD (SIDE A)
110
43
44
1
2
C8536C8537C8538
CL8503
CN8501
C8508
41
42
45
C8514
1
R8627
EQR-COD
SSGE
08
C8628
4
46
C8509
FB8501
C8513
R8515R8516R8517
8
9
IC8603
5
C8529
C8503
C8539
R8503
R8507
4
R8504
5
13
C8504
C8520
IC8501
C8519
FB8506
C8521
L8501
C8507
R8628
C8524
R8501
FB8504
C8512
C8518
L8504
C8535
C8616 C8617
C8613
C8612
C8610
C8618
C8525
R8508
5
1
IC8503
11
610
C8528
R8502
FB8508
CN8502
C8625
C8623
C8621
C8619
R8511R8512
C8530
C8533
C8802
C8801
C8523
C8614
C8626
C8615
C8624
C8622
C8611
C8620
C8534
C8609
L8503
18
19
24
1
C8605
C8606
C8608
C8607
C8627
FB8507
1-881-914-
IC8801
L8801
R8801
13
12
25
C8803
7
6
FB8505
FB8801
FB8602
FB8601
C8510
FB8502
IC8602
4
9
C8603
12
X8601
R8611
R8612
C8602
R8608
R8613
C8515
R8514
2
1
C8501
C8505
08
21
R8802
R8803
815
C8604
R8618
R8619
34
R15
P15
N15
M15
CL8604
L15
K15
J15
H15
G15
F15
E15
D15
C15
B15
A15
10
15
C8601
R14 R13 R12 R11 R10
P14
P13
P12
N14
N13
N12
M12
M14
M13
L12
L14
L13
K12
K14
K13
J12
J14
J13
H12
H14
H13
G12
G14
G13
F12
F14
F13
E12
E14
E13
D14
D13
D12
C14
C13
C12
B14
B13
B12
A14
A13
A12
R8614
C8531
D8503
D8502
D8501
C8526
9
8
72
17
IC8601
1
16
R8610
R9 R8 R7 R6 R5 R4 R3 R2 R1
P9
P8
P7
P11
P10
N9
N8
N7
N11
N10
M9 M8 M7 M6
M11 M10
IC8605
D9
D8
D7
D11
D10
C9
C8
C7
C11
C10
B8
B9
B7
B11
B10
A7
A8A9
A11
A10
R8617
R8605
R8606
CN8503
C8532
R8510
R8509
R8513
712
R8601
R8602
P2
P3
P5
P6
P4
N2
N3
N5
N6
N4
M2
M3
M5
M4
L2
L3
L4
K2
K4
K3
J2
J4
J3
H2
H4
H3
G2
G4
G3
F2
F4
F3
E3
E2
E4
D3
D2
D4
D6
D5
C3
C2
C4
C6
C5
B2
B4
B3
B6
B5
A5
A2
A4
A3
A6
R8624
R8616
R8626
IC8502
C8522
P1
N1
M1
L1
K1
J1
H1
G1
F1
E1
D1
C1
B1
A1
R8623
13
R8620 R8621
R8703
R8625
R8518
R8505
16
C8527
C8706
R8701
R8704
60
59
R8506
C8701 C8702
A9
A8
A7
A3
A2
A1
C8516
C8517
CL8502
C8707 C8708
F9 H9 K9
B9 C9 D9 E9
B8 C8 D8 E8 F8 G8 H8 J8 K8
B7 C7 D7
G9 J9
E7 F7 G7 H7 J7 K7
IC8701
B3 C3 D3 E3 F3 G3 H3 J3 K3
B2 C2 D2 E2 F2 G2 H2 J2 K2
F1 H1 K1
B1 C1 D1 E1 G1 J1
C8704 C8705
R8702
18
CN8601
C8703
C8710
R8705
C8629
1-881-914-
21
Note: All mounted parts are not supplied, but they are included in PJ-104 COMPLETE BOARD.
GP-037 BOARD (SIDE A) GP-037 BOARD (SIDE B)
:GPS Model
C9245
C9247
L9212
46
13
IC9202
L9205
3
4
2
5
1
SF9201
C9206
AT9201
CL9201
CL9205
CL9203
L9204
C9252
C9204
18
CN9201
08
1-882-873-
31
08
SF9202
C9211
VD9201
CL9206
CL9202
CL9204
4
1
L9207
253
C9212
ET9201
C9255
C9256
L9213
IC9203
C9242
C9237
R9202
R9201
C9254
13
C9238
L9202
L9201
C9248
46
C9250
CL9209
C9253
C9239
:GPS Model
C9246
L9214
C9226
C9225
L9211
IC9204
A7A1
A6A5A2 A3 A4
B7B6B5B1 B2 B3 B4
C9244
C6C5C1 C2 C3 C4
C9243
D7D6D5D1 D2 D3 D4
E7E6E5E1 E2 E3 E4
F7F6F5F1 F2 F3 F4
C9230
G7G1
G5
G6G2 G3 G4
C9231
C9232
C9235
CL9210
X9201
L9206
C9240
142
IC9201
12
C9205
C9209
34
1-882-873-
All mounted parts and GP-037 COMPLETE
Note:
BOARD are not supplied, but they are
included in GP386 ASSY.
C9241
C9228
3
C9249
31
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
: Uses unleaded solder.
6-47
Page 100
FP-1582 FLEXIBLE BOARD
FP-1554 FLEXIBLE BOARD
46
42
45
08
CN5505
44
2
141
43
Note: All mounted parts are not supplied, but they are
included in FP-1582 FLEXIBLE COMPLETE BOARD.
C001
43
1
CN5503
41
45
1-886-152-
34
12
SE001
C001
I
44
2
42
46
08
㧪㧼㧵㧨
FP-1554 1-885-379
11
61
FP-1555 FLEXIBLE BOARD
221
08
1-885-379-
FP- 1 555
>PI<
11
AKKA
TH001
D0001
D0002
1-885-383-
11
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Note: FP-1555 FLEXIBLE COMPLETE BOARD is not supplied,
but this is included in ST LED BLOCK ASSY.
: Uses unleaded solder.
6-48
Loading...