Sony HT-CT150 Operating Instruction

4-174-097-12(1)

Home Theatre System

HT-CT150

©2010 Sony Corporation

Operating Instructions

Mode d’emploi

Manual de instrucciones

US

FR

ES

3

WARNING

To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.

The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet,
even if the unit itself has been turned off.

To reduce the risk of fire, do not cover the ventilation
opening of the apparatus with newspapers, tablecloths,
curtains, etc.

Do not place the naked flame sources such as lighted
candles on the apparatus.

To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and do
not place objects filled with liquids, such as vases, on
the apparatus.

As the main plug is used to disconnect the unit from the
mains, connect the unit to an easily accessible AC
outlet. Should you notice an abnormality in the unit,
disconnect the main plug from the AC outlet
immediately.

Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.

Do not expose batteries or apparatus with battery­installed to excessive heat such as sunshine, fire or the
like.

For the customers in the U.S.A

This symbol is intended to alert the user to
the presence of uninsulated “dangerous

voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electric shock to persons.

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the
literature accompanying the appliance.

Owner’s Record

The model and serial numbers are located at the rear of the
subwoofer. Record the serial numbers in the spaces
provided below. Refer to them whenever you call upon
your Sony dealer regarding this product.

Model No. HT-CT150

Serial No.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.

11) Only use attachments/accessories specified by the
manufacturer.

12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

13) Unplug this apparatus during lightning storms or
when unused for long periods of time.

US

2

14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

The following FCC statement applies only to the
version of this model manufactured for sale in the
U.S.A. Other versions may not comply with FCC
technical regulations.

NOTE:

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is
connected.

– Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.

Precautions

On safety

• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.

• Do not climb on the subwoofer, as you may fall down
and injure yourself, or system damage may result.

On power sources

• Before operating the system, check that the operating
voltage is identical to your local power supply. The
operating voltage is indicated on the nameplate at the
rear of the subwoofer.

• If you are not going to use the system for a long time,
be sure to disconnect the system from the wall outlet
(mains). To disconnect the AC power cord (mains
lead), grasp the plug itself; never pull the cord.

• One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet
(mains) only one way. If you are unable to insert the
plug fully into the outlet, contact your dealer.

• AC power cord (mains lead) must be changed only at
the qualified service shop.

On heat buildup

Although the system heats up during operation, this is
not a malfunction. If you continuously use this system
at a large volume, the system temperature of the back
and bottom rises considerably. To avoid burning
yourself, do not touch the system.

On placement

• Place the system in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the system.

• Do not place the system near heat sources, or in a
place subject to direct sunlight, excessive dust, or
mechanical shock.

• Do not place anything at the rear of the subwoofer that
might block the ventilation holes and cause
malfunctions.

• Do not place the syst em near equipment such as a TV,
VCR, or tape deck. (If the system is being used in
combination with a TV, VCR, or tape deck, and is
placed too close to that equipment, noise may result,
and picture quality may suffer. This is especially
likely when using an indoor antenna. Therefore, we
recommend using an outdoor antenna.)

• Use caution when placing the system on surfaces that
have been specially treated (wi th wax, oil, polish, etc.)
as staining or discoloration of the surface may result.

US

continued

US

3

On operation

Before connecting ot her components, be sure to turn of f
and unplug the system.

If you encounter color irregularity on
a nearby TV screen

The system is magnetically shielded to allow it to be
installed near a TV set. However, color irregularities
may still be observed on certain types of TV sets.

If color irregularity is observed...

Turn off the TV set, then turn it on again after 15 to 30
minutes.

If color irregularity is observed
again...

Place the system further away from the TV set.

On cleaning

Clean the system with a soft dry cloth. Do not use any
type of abrasive pad, scouring powder or solvent such
as alcohol or benzine.

If you have any question or problem concerning your
system, please consult your nearest Sony dealer.

Copyrights

This system incorporates Dolby* Digital and Pro Logic
Surround and the DTS** Digital Surround System.

*

Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.

** Manufactured under license under U.S. Patent #'s:

5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and the Symbol are
registered trademarks & DTS Digital Surround and
the DTS logos are trademarks of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.

“x.v.Color” and “x.v.Color” logo are trademarks of
Sony Corporation.

®

ENERGY STAR
registered mark.

As an ENERGY STAR
Sony Corporation ha s determined that
this product meets the ENERGY

®

STAR

guidelines for energy

efficiency.

is a U.S.

®

partner,

This system incorporates High-Definition Multimedia
Interface (HDMI™) technology.

HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.

“BRAVIA Sync” is a trademark of Sony Corporation.

“PlayStation” is a registered trademark of Sony
Computer Entertainment Inc.

US

4

Table of contents

Precautions...............................................3

Getting Started

Unpacking................................................6

Positioning the system .............................7

Connecting the speaker ............................9

Connecting the TV and player, etc. .......10

Connecting other components................12

Connecting the AC power cord (mains

lead) .................................................13

Setting up the sound output of the

connected component ......................13

Playback Options

Index to parts and controls.....................14

Enjoying TV...........................................16

Enjoying other components ...................17

Surround Function

Enjoying the surround effect..................19

“BRAVIA” Sync Features

What is “BRAVIA” Sync?.....................20

Preparing for “BRAVIA” Sync .............20

Enjoying Blu-ray Disc/DVD..................21

(One-Touch Play)

Enjoying the TV sound from the

system ..............................................22

(System Audio Control)

Turning off the system, TV and the

connected components.....................23

(System Power Off)

Using the power saving function ...........23

(HDMI SIGNAL PASS THRU)

Setting the Audio Return Channel function

to off ................................................24

Advanced Settings

Controlling connected Sony components

with the remote ................................25

Changing the input button assignments of

the remote ........................................28

Settings and adjustments using the

amplifier menu.................................30

Additional Information

Troubleshooting .................................... 34

Specifications........................................ 36

Index...................................................... 38

US

5

Getting Started

Unpacking

• Subwoofer (SA-WCT150) (1)

• Speaker cord (1)

• Remote commander (RM­AAU072) (1)

• Digital optical cord for a TV
(2.5 m) (1)

• Speaker (SS-CT150) (1)

• R6 (size AA) batteries (2)

• Warranty (1)

• Operating Instructions (1)

Inserting batteries into the remote

Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment. To use the remote, point it at the remote sensor in the front panel
display of the subwoofer.

Notes

• Do not leave the remote in an extremely hot or humid place.

• Do not use a new battery with an old one.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.

US

6

Positioning the system

Connecting the speaker cord to the speaker

The connectors of the speaker cord are color-coded depending on the type of speaker. Connect the
connectors of the speaker cord to match the color of the speaker jacks.

Rear of the speaker

R CENTER L

Green

Red

White

Getting Started

A

Note

• When you install the speaker on a wall, be careful not to stumble over the cord connected to the speaker.

A Speaker cord

(supplied)

continued

US

7

Installing the speaker on a wall

You can install the speaker on the wall.

Notes

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a wall beam. Install the speaker on a vertical and flat reinforced area of the wall.

• Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety
during the installation.

• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength,
improper screw installation or natural calamity, etc.

1 Prepare screws (not supplied) that are suitable for the holes on the back of the speaker.

See the illustrations below.

4 mm (1/6 inches)

more than 25 mm (1 inch)

5mm
(1/5 inches)

10 mm
(2/5 inches)

Hole on the back of the speaker

2 Fasten the screws to the wall. The screws should protrude 6 to 7 mm (approx. 1/4

inches).

265 mm

(10 2/5 inches)

6 to 7 mm
(approx. 1/4 inches)

3 Hang the speaker onto the screws.

Align the holes on the back of the speaker to the screws, then hang the speaker onto the two screws.

US

8

Connecting the speaker

The connectors of the speaker cord are color-coded depending on the type of speaker. Connect the
connectors of the speaker cord to match the color of the SPEAKERS jacks.

Rear of the
subwoofer

DMPORT

DC 5V

0.7A MAX

Green

Red White

Speaker

L

ONLY FOR
SS-CT150

A

AUDIO I N

SA-CD/CD

SAT/CATV INBD INDVD IN

HDMI

L

R

AUDIO I N

TV

ARC

TV OUT

DIGITALSPEAKERS

COAX IN

OPT IN

VIDEO

TVSAT/CATVR CENTER

Getting Started

A Speaker cord (supplied)

US

9

Connecting the TV and player, etc.

Connect the TV and/or player, etc., with HDMI jacks to the system using an HDMI cable.
By connecting Sony “BRAVIA” Sync-compatible components using HDMI cables and by setting the
Control for HDMI function via the TV for each connected component, operation can be simplified. See
““BRAVIA” Sync Features” (page 20).

DVD player, etc.

HDMI OUT

HDMI cable
(not supplied)

HDMI cable
(not supplied)

TV

HDMI IN

Rear of the
subwoofer

Blu-ray Disc player, etc.

HDMI OUT

DMPORT

DC 5V

0.7A MAX

L

HDMI cable
(not supplied)

ONLY FOR
SS-CT150

AUDIO I N

SA-CD/CD

SAT/CATV INDVD IN BD IN

L

R

AUDIO I N

TV

HDMI

DIGITALSPEAKERS

OPT IN

Digital optical cord
(not supplied)

ARC

TV OUT

COAX IN

TVSAT/CATVR CENTER

VIDEO

HDMI cable
(not supplied)

Digital Audio OUT
(optical)

Digital optical cord fo r a TV
(supplied)

Satellite tuner or cable television
tuner, etc., with an HDMI jack

Digital Audio OUT
(optical)

HDMI OUT

10

US

Notes

• The system is compatible with the Audio Return Channel (ARC) function. If you connect the system to the ARC­compatible TV’s HDMI jack via an HDMI cable, you do not need to connect the TV to the system with the digital
optical cord (page 24).

• You can see the letters “ARC” beside the TV’s HDMI jack if it is compatible with the ARC function. Even if you
connect an HDMI cable to the jack, if the HDMI input jack is not compatible with the ARC function, you cannot
use the ARC function.

• The ARC function is available only when Control for HDMI is set to on.

• Depending on the satellite tuner, multi-channel sound may not be output. In this case, connect a digital optical cord
in addition to an HDMI cable and set “INPUT MODE” to “OPT” in the AMP menu (page 32).

• Connect a “PlayStation 3,” etc., to any available HDMI jack. All the HDMI jacks on the system function in the same
way.

• The HDMI jack connections have priority when you connect different components to the system using the INPUT
OPT/INPUT COAX and HDMI jacks.

• When connecting a TV that does not have a digital optical audio output jack, connect the TV to the system using
an analog audio cord (not supplied).

Tip

• Even if the system is tu rned off (active standby mode), the HDMI signal will be sent from the connected component
to the TV via the HDMI connection. You can enjoy image and sound from the component on the TV.

Notes on HDMI connections

• Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p, Deep Color, or 3D images

may not be displayed properly.

• Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.

• Check the setup of the connected component if an image is poor or the sound does not come out of a

component connected via the HDMI cable.

• Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be

suppressed by the connected component.

• Sound may be interrupted when the sampling frequency or the number of channels of audio output

signals from the playback component is switched.

• When the connected component is not compatible with copyright protection technology (HDCP), the

image and/or the sound from the HDMI TV OUT jack may be distorted or may not be output.
In this case, check the specification of the connected component.

• We do not recommend using an HDMI-DVI conversion cable.

• When “TV,” “DMPORT,” “SA-CD/CD,” or “VIDEO” is selected for the input source of the system,

video signals via the HDMI input jack (BD, DVD, SAT/CATV) that was selected last time are output
from the HDMI TV OUT jack.

• This system supports Deep Color, “x.v.Color,” and 3D transmission.

• To enjoy 3D images, connect 3D-compatible TV and video components (Blu-ray Disc player, Blu-

ray Disc recorder, “PlayStation 3,” etc.) to the system using High Speed HDMI cables, put on 3D
glasses, and then play back 3D-compatible content.

Getting Started

11

US

Connecting other components

When connecting components that do not have HDMI jacks, such as a “PlayStation 2,” a DVD player,
a satellite tuner, or a cable television tuner, etc., set “CTRL HDMI” to “OFF” in the AMP menu of the
system (page 21).

Other audio components, etc.

DVD player, etc.

Audio cord
(not supplied)

Digital coaxial cord
(not supplied)

Digital Audio OUT
(coaxial)

Audio signal OUT

VIDEO OUT

To the VIDEO IN of
the TV.

Rear of the
subwoofer

DMPORT

DC 5V

0.7A MAX

L

ONLY FOR
SS-CT150

AUDIO I N

SA-CD/CD

SAT/CATV INBD INDVD IN

HDMI

L

R

AUDIO I N

Satellite tuner or cable

TV

ARC

TV OUT

DIGITALSPEAKERS

COAX IN

OPT IN

TVSAT/CATVR CENTER

VIDEO

television tuner, etc.,
without an HDMI jack

Digital Audio OUT
(optical)

DIGITAL MEDIA
PORT adapter

Notes

Digital optical cord
(not supplied)

VIDEO OUT

To the VIDEO IN of the TV.

• Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the system is turned on.

• When you connect the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark
facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and
hold A and then pull out the connector.

12

A

US

Connecting the AC power cord (mains lead)

Before connecting the AC power cord (mains lead) of the system to a wall outlet (mains), connect all
the other components and TV to the system.

Notes

• After connecting the AC power cord (mains lead), wait about 20 seconds before turning on the power by pressing

?/1.

• Connect the system to an easily accessible AC outlet (mains). Should you notice an abnormality in the system,
disconnect the main plug from the AC outlet (mains) immediately.

Setting up the sound output of the connected component

To enjoy sound in multi-channel format (DTS, Dolby Digital, multi-channel LPCM), you need to make
the audio output settings of the connected component. Set the connected component to output sound in
multi-channel format. For details on audio output settings, refer to the operating instructions supplied
with the connected component.

Getting Started

13

US

Playback Options

Index to parts and controls

For more information, see the pages indicated in parentheses.

Subwoofer

Top view

POWER/

ACTIVE STANDBY

INPUT

SELECTOR

VOLUME VOLUME

A ?/1 (on/standby)
B INPUT SELECTOR

Press to select the input source to play back.
Every time you press the button, the input
source changes cyclically as follows: TV t
BD t DVD t SAT/CATV t VIDEO
t SA-CD/CD t DMPORT t TV……

US

14

C VOLUME –
D VOLUME +
E Front panel display

Front panel display (subwoofer)

POWER/

ACTIVE STANDBY

Playback Options

A POWER/ACTIVE STANDBY indicator

Lights as follows:
Green: The system is turned on.
Amber: Only HDMI parts of the system

are on (The Control for HDMI
function is working).

No light: The system is turned off.

Note

• The amber light turns off 30 seconds after you
turn off the TV. However, if you set “PASS
THRU” to “ON” in the AMP menu, the indicator
stays amber even if you turn off the TV.

B Audio format indicators

Light up according to the audio format that
is being input to the system.

D: Dolby Digital

PLII: Dolby Pro Logic II
LPCM: Linear PCM
DTS

C NIGHT (page 32)

Lights up in NIGHT MODE.

D SLEEP (page 33)

Flashes when the sleep timer is active.

E HDMI (page 10)

Lights up when HDMI components are
being used or when an ARC signal is being
input to the system while TV is selected as
the input source.

F COAX/OPT

Light up according to the cable which you
are using.

G MUTING

Lights up when the sound is turned off.

H Remote sensor
I Message display area

Displays volume, selected input source,
audio input signal, etc.

continued

15

US

Remote control

This section describes subwoofer and speaker
button operation. See page 25 for details on the
button operation of connected components.

Note

• Point the remote towards the remote sensor ( ) of the
subwoofer.

C SLEEP

Press to turn off at a preset time when you
want to fall asleep listening to music. You
can preset the time in 10-minute increments.

D NIGHT MODE

Press to reproduce dialog clearly even at a
low volume level. This function is useful for
enjoying sound at night.

E AMP MENU (page 30)
F SOUND FIELD +/– (page 19)
G MUTING
H MASTER VOL +/–

Press to adjust the volume.

I C, X, x, c or

Press C, X, x or c to select the menu items.
Then press to enter the selection.

Enjoying TV

?/1

TV

* The 5, N, AUDIO and SOUND FIELD + buttons

have a tactile dot. Use it as a guide during operation.

A ?/1 (on/standby)
B Input buttons

Press one of the buttons to select the
component you want to use.

US

16

MASTER
VOL +/–

1 Turn on the TV and choose a program.

Refer to the operating instructions of your
TV for details.

2 Turn the system on.
3 Press TV on the remote.
4 Adjust the volume by pressing

MASTER VOL +/–.

Tip

• The sound may be output from the TV’s speaker. In
this case, turn the volume of the TV’s speaker down
to minimum.

If you are using “BRAVIA” Sync
(System Audio Control)

You do not need to perform steps 2 and 3 above.
When you turn on the TV, the system is also
turned on, and the input source changes
automatically. You can also adjust the system’s
volume using the TV’s remote. If you turn off the
system, sound is output from the TV’s speaker.
For details on setting “BRAVIA” Sync, see
“Preparing for “BRAVIA” Sync” (page 20).

Tip

• The system is not turned on when you turn the TV on
if sound was being output from the TV speakers the
last time the TV was turned off.

Enjoying other
components

Input
buttons

MASTER
VOL +/–

Playback Options

?/1

1 Play the connected component.
2

Turn on the system.

continued

17

US

3 Press the input buttons to display the

input source in the front panel display.

Input source Playable component

TV TV, etc. connected to the TV

jack

BD Blu-ray Disc player, etc.

connected to the BD jack

DVD DVD player, etc. connected to

the DVD jack

SAT/CATV Satellite tuner or cable

television tuner, etc. connected
to the SAT/CATV jack

VIDEO DVD player, etc. connected to

the DIGITAL COAX IN
VIDEO jack

SA-CD/CD CD player, et c. connected to the

SA-CD/CD AUDIO IN jack

DMPORT Portable audio player, etc.

connected to the DMPORT jack

4 For video components, change the TV’s

input to the HDMI input you chose in
step 3.

For details, refer to the operating
instructions of your TV.

5 Adjust the volume by pressing

MASTER VOL +/–.

Tips

• The sound may be output from the TV’s speaker. In
this case, turn the volume of the TV’s speaker down
to minimum.

• Even if you playback Dolby True HD, Dolby Digital
Plus or DTS HD with a connected component
compatible with these sound formats, the system
accepts the signal as Dolby Digital or DTS. When you
playback these high-quality sound formats, set the
connected component to output the sound in multi­channel PCM, if possible.

Notes

• When you connect the video output jack of the
DIGITAL MEDIA PORT adapter to the video input
jack of the TV, set “CTRL HDMI” to “OFF” in the
AMP menu of the system (page 21). The images of a
component connected to the DIGITAL MEDIA
PORT adapter will not be played on the TV if “CTRL
HDMI” is set to “ON.”

• To enjoy the sound of a component without
displaying the images when “CTRL HDMI” is set to
“ON,” turn off the TV first and then reset the power of
the system.
If you turn on the system first and then turn off the
TV, all components connected to the TV will be
turned off because of the Control for HDMI function.

If you are using “BRAVIA” Sync
(One-Touch Play)

You do not need to perform steps 2 to 4 above.
When you turn on the connected components,
the system and the TV are also turned on, and the
input source changes automatically. You can
also adjust the system’s volume using the TV’s
remote.
For details on setting “BRAVIA” Sync, see
“Preparing for “BRAVIA” Sync” (page 20).

Tip

• The system is not turned on when you turn the TV on
if sound was being output from the TV speakers the
last time the TV was turned off.

18

US

Available sound fields

Surround Function

Enjoying the surround
effect

Selecting the sound field

This system can create multi-channel surround
sound. You can select one of system’s optimized
pre-programmed sound fields.

SOUND
FIELD +/–

Press SOUND FIELD +/–.

The present sound field appears in the front panel
display.

Each time you press SOUND FIELD +/–, the
display changes cyclically as follows:
STANDARD y MOVIE y DRAMA y
NEWS y SPORTS y GAME y MUSIC
y 2CH STEREO y P.AUDIO y
STANDARD …

Sound field Effect

STANDARD* Suits various sources.

MOVIE* Recreates powerful and realistic

sound, along with clear dialog.

DRAMA* Suited for TV dramas.

NEWS* Produces the announcer’s voice

clearly.

SPORTS* Produces the play-by-play

commentary clearly and realistic
sound with surround effects, such as
cheering, etc.

GAME* Produces powerful and realistic

sound, suited for playing video
games.

MUSIC* Suited for music programs or music

videos on Blu-ray Discs/DVDs.

2CH STEREO Suited for music CDs.

P.AUDIO** Suited to replay portable audio

source.

* These sound fields are not available when

“DMPORT” is selected by pressing INPUT
SELECTOR.

** “P.AUDIO” appears only when “DMPORT” is

selected.

Tips

• You can set a different sound field for each input
source.

• The sound field default setting for “DMPORT” is
“P.AUDIO,” and for other sources, “STANDARD.”

• When “DMPORT” is selected by pressing INPUT
SELECTOR, the center speaker produces no sound.

• Some speakers will not produce sound depending on
the input signal, such as monaural programs.

• When “2CH STEREO” or “P.AUDIO” is selected,
the center speaker produces no sound.

• If you press the THEATER button on a Sony TV
remote when “CTRL HDMI” is set to “ON,” the
sound field changes to “MOVIE” (some Sony TVs
excluded).

Surround Function

19

US

“BRAVIA” Sync Features

What is “BRAVIA” Sync?

By connecting Sony components that are
compatible with “BRAVIA” Sync via an HDMI
cable (not supplied), operation is simplified as
below:

• One-Touch Play (page 21)

• System Audio Control (page 22)

• System Power Off (page 23)

Preparing for “BRAVIA”
Sync

To use “BRAVIA” Sync, set the Control for
HDMI function to on for the connected
components.
When you connect a Sony TV with the Control
for HDMI function, the Control for HDMI
function for the system and the connected
components can be set simultaneously by setting
the Control for HDMI function of the TV.

“BRAVIA” Sync is compatible with Sony TVs,
Blu-Ray Disc/DVD players, AV amplifiers, etc.,
with the Control for HDMI function.

CONTROL FOR HDMI is a mutual control
function standard used by CEC (Consumer
Electronics Control) for HDMI (High-Definition
Multimedia Interface).

The Control for HDMI function will
not operate correctly in the
following cases:

• When you connect the system to components
which do not correspond with the Control for
HDMI function.

• When you connect the system and components
using other than an HDMI connection.

• When you connect non-Sony components
which are compatible with the Control for
HDMI function.

We recommend that you connect products
featuring “BRAVIA” Sync to this system.

Note

• Depend ing on the connected components, th e Control

for HDMI function may not work. Refer to the
operating instructions of the components.

?/1

AMP
MENU

C, X, x, c,

1 Make sure that the system is connected

to the TV and the connected
components via HDMI cables (not
supplied).

2 Turn on the system, the TV and the

connected components.

3 Select the input of the system and the

HDMI input of the TV (SAT/CATV, DVD,
BD), so that an image from a connected
component is displayed.

20

US

4 Display the list of the HDMI

components on the TV menu, and set
the Control for HDMI function to on for
the connected components.

The Control for HDMI function for the
system and the connected components are
simultaneously set to on.

After you finish the setting, “COMPLETE”
appears in the front panel display.

Note

• For details on setting the TV and the connected
components, refer to their operating instructions.

If “COMPLETE” does not appear
after performing the steps above

Set the Control for HDMI function to on for both
the system and the connected component
individually.

1 Press AMP MENU.
2 Press X/x repeatedly until “SET HDMI”

appears, then press or c.

3 Press X/x repeatedly until “CTRL

HDMI” appears, then press or c.

4 Press X/x to select “ON.”
5 Press AMP MENU.

The AMP menu turns off. The Control for
HDMI function is set to on.

6 Select the input of the system

connected to the component you want
to use the Control for HDMI function for
(SAT/CATV, DVD, BD).

7 Set the Control for HDMI function of the

connected component to on.

For details on setting the connected
component, refer to its operating
instructions.

If you add or reconnect a
component

Perform steps of “Preparing for “BRAVIA”
Sync” (page 20) and “If “COMPLETE” does not
appear after performing the steps above” again.

Notes

• If the Control for HDMI function for the connected
component cannot be set simultaneously by setting
“CONTROL FOR HDMI” of the TV, set the Control
for HDMI function using the menu of the connected
component.

• For details on setting the TV and the connected
components, refer to their operating instructions.

Tip

• The default setting of the Control for HDMI function
of the system is “ON.”

Setting the Control for HDMI
function to off

Set the Control for HDMI function to off when
you connect components not compatible with
“BRAVIA” Sync, or that do not have HDMI
jacks, etc.

AMP
MENU

C, X, x, c,

1 Press AMP MENU.
2 Press X/x repeatedly until “SET HDMI”

appears, then press or c.

3 Press X/x to select “CTRL HDMI,” then

press or c.

4 Press X/x to select “OFF.”
5 Press AMP MENU.

The AMP menu turns off.

Enjoying Blu-ray Disc/DVD

(One-Touch Play)

Play back a connected component.

The TV turns on automatically and switches to
the appropriate HDMI input.

“BRAVIA” Sync Features

continued

21

US

Tip

• Even if the system is turned off (active standby
mode), the HDMI signal will be sent from the
connected component to the TV via the HDMI
connection. You can enjoy image and sound of the
component on the TV.

Note

• Depending on the TV, the start of the content may not
be output.

Notes

• When the TV is turned on before this system is turned
on, the TV sound will not be output for a moment.

• Depending on the TV, when you adjust the system’s
volume using TV’s remote, the volume level appears
on the TV screen, in the same way it would appear
when you adjust the TV’s volume. In this case, the
volume level that appears on the TV screen and the
system’s front panel display may differ.

Enjoying the TV sound
from the system

(System Audio Control)

You can enjoy the TV sound from the speakers
of the system by means of a simple operation.
You can also adjust the volume and turn off the
sound of the system using the TV remote. For
details, refer to the operating instructions of the
TV.

?/1

AMP

C, X, x, c,

Press ?/1 to turn on the system.

The sound is output from the speaker of the
system. Sound output reverts to the TV's speaker
when you turn the system off.

MENU

Using the Volume Limit
function

When the System Audio Control function is
active and the output method changes from the
TV speaker to the system speakers
automatically, loud sound may be output
depending on the volume level of the system.
You can prevent this by limiting the volume
level.

1 Press AMP MENU.
2 Press X/x repeatedly until “SET HDMI”

appears, then press or c.

3 Press X/x repeatedly until “VOL LIMIT”

appears, then press or c.

4 Press X/x to select the volume limit you

want.

The volume limit changes as follows:

MAX y 49 y 48 … 2 y 1 y MIN

5 Press AMP MENU.

The AMP menu turns off.

Notes

• This function is available only when the Control for
HDMI function is set to on.

• This function is not available when the output method
changes from the system speakers to the TV speaker.

Tips

• We re commend that you set the volume limit to a little
lower than the volume you usually listen to.

• Regardless of the volume limit you set, the VOLUME
+/– buttons of the system and the MASTER VOL +/–
buttons of the remote are operable.

• If you do not want to limit the volume level, select
“MAX.”

22

US

Turning off the system, TV
and the connected
components

(System Power Off)

When you turn the TV off by using the power
button on the TV’s remote, the system and the
connected components turn off automatically.
Also, when you turn the TV off by using the
system’s remote, the system and the connected
components turn off automatically.

AV ?/1

Note

• Depending on the status, the connected components
may not be turned off. For details, refer to the
operating instructions of the connected components.

Using the power saving
function

(HDMI SIGNAL PASS THRU)

When using “BRAVIA” Sync, you can enjoy
image and sound from a Blu-ray Disc, etc., on
the TV, even if the system is in standby mode.
Power consumption in standby mode is also
reduced automatically when the TV is turned off
if “PASS THRU” is set to “AUTO.”
The default setting is “AUTO.”

Note

• This function is available only when “CTRL HDMI”
is set to “ON.”

AMP
MENU

C, X, x, c,

“BRAVIA” Sync Features

TV
(yellow)

While pressing and holding TV (yellow),
press AV ?/1.

The TV, the system, and the connected
components are turned off.

1 Press AMP MENU.
2 Press X/x repeatedly until “SET HDMI”

appears, then press or c.

3 Press X/x to select “PASS THRU,” then

press or c.

continued

23

US

4 Press X/x to select the setting.

• AUTO: When the TV is turned on while
the system is in standby mode, the
system outputs HDMI signals
from the system’s HDMI output
jack. We recommend this setting
if you use a TV that is compatible
with “BRAVIA” Sync. This
setting saves power in standby
mode compared with the “ON”
setting.

• ON: When the system is in standby
mode, the system continuously
outputs HDMI signals from the
system’s HDMI output jack.

Note

• When “AUTO” is selected, it may take a little

more time for the picture and sound to be output
to the TV than when “ON” is selected.

5 Press AMP MENU.

The AMP menu turns off.

Setting the Audio Return
Channel function to off

If the TV is compatible with the Audio Return
Channel (ARC) function, an HDMI cable
connection also sends a digital audio signal from
the TV. You do not need to make a separate
audio connection for listening to TV sound.
If you do not use the ARC function, connect the
system and TV via digital optical cord and set
“ARC” to “OFF” in the AMP menu.

3 Press X/x repeatedly until “ARC”

appears, then press or c.

4 Press X/x to select “OFF”.

• ON: The ARC function turns on.

• OFF: The ARC function turns off.

5 Press AMP MENU.

The AMP menu turns off.

Note

• When “CTRL HDMI” is set to “OFF,” the ARC
function and its setting are not available.

AMP

C, X, x, c,

MENU

1 Press AMP MENU.
2 Press X/x repeatedly until “SET HDMI”

appears, then press or c.

US

24

Advanced Settings

Controlling connected
Sony components with the
remote

You can control connected Sony components
with the remote of this system.
Some functions may not be selectable depending
on the equipment. In that case, select them using
the remote control supplied with the equipment.

* The 5, N, AUDIO and SOUND FIELD + buttons

have a tactile dot. Use it as a guide during operation.

To control the component

1 Press one of the input buttons 3 (BD,

DVD, SAT/CATV, TV, VIDEO, or
DMPORT) to select the component you
want to operate.

The component assigned to the selected
input button becomes operable.

2 Referring to the following table, press

the corresponding button for the
operation.

Common operations

Remote Button Function

1 TV ?/1

AV ?/1
(on/standby)

4 ENTER Enters the selection.

qk C, X, x, c, Selects a menu item and

w; Color buttons Displays an operation

wg CLEAR Clears the selection.

Turns on or off the Sony
TV or audio/video
components that the
remote is assigned to
operate.

Press 1 TV
and 2
time to turn off the system
and all other components
that the remote is assigned
to operate (SYSTEM
STANDBY).

For TV, while pressing and
holding qf TV (yellow),
press 4 ENTER.

For other components,
while pressing and holding
qd SHIFT, press 4
ENTER.

enters the selection.

guide on the TV screen
when the color buttons are
available. Follow the
operation guide to perform
a selected operation.

For TV, while pressing and
holding qf TV (yellow),
press wg CLEAR.

For other components,
while pressing and holding
qd SHIFT, press wg
CLEAR.

?/1/AV ?/1

?/1 at the same

Advanced Settings

continued

25

US

Remote Button Function

wh Number buttons Selects channels and tracks

directly.
For TV, press and hold qf

TV (yellow), and press the
number buttons to select
channels.

For other components,
press and hold qd SHIFT,
and press the number
buttons to select channels
or tracks.

To control a TV

While pressing and holding qf TV (yellow),
press the buttons with a yellow dot or
yellow printing.

Remote Button Function

5 DISPLAY Displays the current

7 TOOLS/

OPTIONS

8 MENU/HOME Allows you to select

qs TV CH +/– Selects the next (+) or

qg MUTING Turns off the sound.
qh TV VOL +/– Adjusts the volume.
qj O RETURN/EXIT Returns to the previous

qk C, X, x, c, Selects a menu item and

ql GUIDE Displays the guide when

wa AUDIO Selects the audio format/

channel number, etc.

Enables you to access
various viewing options
and change/make
adjustments according to
the source and screen
format.

channels or input sources
and change the settings for
your TV.

previous (–) channel.

screen of any displayed
menu.

enters the selection.

you are watching analog or
digital channels.

track.

Remote Button Function

wj THEATER Automatically sets the

wk INPUT Selects input.

optimal picture settings for
watching movies, such as
low-light settings, when
you connect a Sony TV
that is compatible with the
THEATER button
function. Also, audio is
automatically switched to
the audio output of this
system when you connect
the TV and the system with
HDMI connection, and the
Control for HDMI function
is set to on.

To control the DVD recorder/Blu­ray Disc recorder

Remote Button Function

6 ANGLE Switches to other viewing

8 MENU/HOME Displays the menu.
9 m/M To fast reverse or to fast

0 ./> To go to the beginning of

qa N (playback)/X

(pause, press again to
resume normal
playback)/x (stop)

qk C, X, x, c, Selects a menu item and

wa AUDIO Selects the audio format/

ws SUBTITLE Selects the subtitle

wd TOP MENU Displays the top menu/disc

wf POP UP/MENU Displays the BD-ROM’s

angles when multi-angles
are recorded on a DVD
VIDEO.

forward the disc when
pressed during playback.

the previous or next
chapter or track.

Play mode buttons.

enters the selection.

track.

language when
multilingual subtitles are
recorded on a BD-ROM/
DVD VIDEO.

menu.

Pop-up Menu, or the
DVD’s menu.

26

US

To control the DVD player/Blu-ray
Disc player

Remote Button Function

6 ANGLE Switches to other viewing

8 MENU/HOME Displays the menu.
9 m/M To fast reverse or to fast

0 ./> To go to the beginning of

qa N (playback)/X

(pause, press again to
resume normal
playback)/x (stop)

qk C, X, x, c, Selects a menu item and

wa AUDIO Selects the audio format/

ws SUBTITLE Selects the subtitle

wd TOP MENU Displays the top menu/dis c

wf POP UP/MENU Displays the BD-ROM’s

angles when multi-angles
are recorded on a DVD
VIDEO.

forward the disc when
pressed during playback.

the previous or next
chapter or track.

Play mode buttons.

enters the selection.

track.

language when
multilingual subtitles are
recorded on a BD-ROM/
DVD VIDEO.

menu.

Pop-up Menu, or the
DVD’s menu.

To control the HDD/DVD COMBO

Remote Button Function

6 ANGLE Switches to other viewing

8 MENU/HOME Displays the menu.
9 m/M To fast reverse or to fast

0 ./> To specify the previous or

angles when multi-angles
are recorded on a DVD
VIDEO.

forward the disc when
pressed during playback.

next chapter or track.

Remote Button Function

qa N (playback)/X

(pause, press again to
resume normal
playback)/x (stop)

qk C, X, x, c, Moves the highlight

wa AUDIO Selects the audio format/

ws SUBTITLE Selects the subtitle

wd TOP MENU Displays t he top menu/disc

wf POP UP/MENU Displays the BD-ROM’s

Play mode buttons.

(cursor) and selects the
item.

track.

language when
multilingual subtitles are
recorded on a BD-ROM/
DVD VIDEO.

menu.

Pop-up Menu, or the
DVD’s menu.

To control the SAT

Remote Button Function

8 MENU/HOME Displays the menu.
qk C, X, x, c, Selects a menu item and

ql GUIDE Displays the guide menu.

Note

• The above explanations are intended to serve as an
example only. Depending on the component, the
above operations may not be possible, or may operate
differently than described.

enters the selection.

To control the connected
component through DMPORT
connection

Remote Button Function

5 DISPLAY Press to select the setting

8 MENU Displays the menu.
9 m/M Press to fast reverse or to

0 ./> Press to skip chapters.
qa N (playback)/X

(pause)/x (stop)

of the front panel display.

fast forward the disc when
pressed during playback.

Play mode buttons.

Advanced Settings

continued

27

US

Remote Button Function

qj O RETURN Returns to the previous

qk C, X, x, c, Selects a menu item and

screen of any displayed
menu.

enters the selection.

Changing the input button
assignments of the remote

You can change the factory settings of the input
buttons to suit the components in your system.
For example, if you connect a Blu-ray Disc
player to the DVD jack on the system, you can
set the DVD button on this remote to control the
Blu-ray Disc player.
You cannot change the remote assignments for
TV and DMPORT.

INPUT

Number
buttons

AV ?/1

?/1

Input
buttons

1 Press and hold the input button whose

assignment you want to change, and
then press and hold AV ?/1 at the same
time.

Example: While holding down DVD, press
and hold AV ?/1.

2 While continuing to hold down AV ?/1,

release the input button you selected in
step 1.

Example: While continuing to hold down
AV ?/1, release DVD.

3 While continuing to hold down AV ?/1,

refer to the following table and press
the corresponding number button for
the category you want.

Example: While continuing to hold down
AV ?/1, press 1.

4 Release the number button you

selected in step 3, and then release AV
?/1.

Example: Release 1, then release AV ?/1.
Now you can use the DVD button to control
the Blu-ray Disc player.

MASTER
VOL +/–

US

28

Categories and the
corresponding buttons for BD,
DVD, SAT/CATV, VIDEO and SA­CD/CD

Categories Press

Blu-ray Disc player
(command mode BD1)

Blu-ray Disc recorder
(command mode BD3)

DVD player
(command mode DVD1)

DVD recorder
(command mode DVD3)

VCR (command mode VTR3) 5

CD player 6

c)

DSS

a)

The initial setting of the BD button. For details on the
BD1 or BD3 setting, refer to the operating
instructions supplied with the Blu-ray Disc player or
Blu-ray Disc recorder.

b)

The initial setting of the DVD button. Sony DVD
recorders are operated with a DVD1 or DVD3
setting. For details, refer to the operating instructions
supplied with the DVD recorders.

c)

The initial setting of the SAT/CATV button.

a)

b)

1

2

3

4

7

To clear all remote button
assignments

While holding down MASTER VOL –, press
?/1 and INPUT. Then, release the buttons.
The remote is reset to its initial settings.

Advanced Settings

29

US

Settings and adjustments
using the amplifier menu

SET
HDMI

*

CTRL
HDMI

ON
OFF

Using the AMP menu

You can set the following items with AMP
MENU on the remote.
The default settings are underlined.

AMP MENU

LEVEL CNT

TONE BASS –6, –5, … 0,

AUDIO

LEVEL

SW LEVEL –6, –5, … 0

AUDIO
DRC

TREBLE –6, –5, … 0

A/V SYNC ON

DUAL
MONO

NIGHT
MODE

–6, –5, … 0,
… +5, +6

… +5, +6

MAX
STD
OFF

… +5, +6

… +5, +6

OFF

MAIN
SUB
MAIN/SUB

ON
OFF

VOL

**

LIMIT

PASS

**

THRU

**

ARC

SYSTEM

,

,

* See ““BRAVIA” Sync Features” (page 20).

** This setting appears only when “CTRL HDMI” is

set to “ON.”

C, X, x, c,

DIMMER ON

DISPLAY ON

SLEEP OFF, 10M,

AUTO
STBY

MAX, 49, 48,
… 2, 1, MIN

AUTO
ON

ON
OFF

OFF

OFF

20M, …
80M, 90M

ON
OFF

AMP
MENU

30

INPUT
MODE

AUTO
OPT

1 Press AMP MENU to turn on the AMP

menu.

2 Press C/X/x/c repeatedly to select the

item and the setting.

3 Press AMP MENU to turn off the AMP

menu.

US

Tip

• These settings are retained even if you disconnect the
AC power cord (mains lead).

The following pages show details for each
setting.

Setting the speaker level (CNT
LEVEL, SW LEVEL)

You can adjust the level and the balance of the
center speaker and subwoofer.

1 Select “LEVEL” in the AMP menu, then

press or c.

2 Select “CNT LEVEL” or “SW LEVEL,”

then press or c.

• CNT LEVEL: Adjusts the center speaker
level.

• SW LEVEL: Adjusts the subwoofer
level.

3 Select the parameter you want and

press .

The parameter of “CNT LEVEL” and “SW
LEVEL” is from “–6” to “+6” in 1-step
increments. The default setting is “0.”

Enjoying Dolby Digital sound
at low volume (AUDIO DRC)

Narrows the dynamic range of the sound track.
Useful for enjoying movies at low volume.
AUDIO DRC only applies to Dolby Digital
sources.

1 Select “LEVEL” in the AMP menu, then

press or c.

2 Select “AUDIO DRC,” then press or

c.

3 Select the setting and press .

• OFF: No compression of dynamic range.

• STD: Reproduces the sound track with

the kind of dynamic range that the
recording engineer intended.

• MAX: Compresses dynamic range fully.

Adjusting the bass and treble
level (BASS, TREBLE)

You can adjust the bass and treble level easily.

1 Select “TONE” in the AMP menu, then

press or c.

2 Select “BASS” or “TREBLE,” then

press or c.

• BASS : Adjusts the bass level.

• TREBLE : Adjusts the treble level.

3 Select the parameter you want and

press .

The parameter is from “–6” to “+6” in 1-step
increments. The default setting is “0.”

Adjusting the delay between
the sound and the image (A/V
SYNC)

You can delay the sound using this function
when the image is slower than the sound.

1 Select “AUDIO” in the AMP menu, then

press or c.

2 Select “A/V SYNC,” then press or c.
3 Select the setting and press .

• OFF: No adjustment.

• ON: Adjusts the difference between
picture and sound.

Notes

• You may not be able to adjust the delay between
sound and image perfectly using this function.

• This function is useful only for Dolby Digital, DTS
and Linear PCM (2ch) input via digital coaxial cord,
digital optical cord or HDMI cable.

Advanced Settings

continued

31

US

Enjoying multiplex broadcast
sound (DUAL MONO)

You can enjoy multiplex broadcast sound when
the system receives an AC-3 multiplex broadcast
signal.

Note

• To receive an AC-3 signal, you need to connect a
digital satellite tuner to the system with an optical
cable or coaxial cable, and set the digital output mode
of the digital satellite tuner to AC-3.

1 Select “AUDIO” in the AMP menu, then

press or c.

2 Select “DUAL MONO,” then press

or c.

3 Select the setting and press .

• MAIN: Plays back only the main
channel.

• SUB: Plays back only the sub
channel.

• MAIN/SUB: Main sound is output from
the left speaker and sub
sound is output from the
right speaker.

Setting the sound from the
satellite tuner (INPUT MODE)

Even if you connect the satellite tuner to the
HDMI SAT/CATV input jack of the system,
multi-channel sound may not be output
depending on the satellite tuner. In this case,
connect a digital optical cord to the SAT/CATV
OPT IN jack of the system in addition to an
HDMI cable, and make the following setting.

1 Select “AUDIO” in the AMP menu, then

press or c.

2 Select “INPUT MODE,” then press

or c.

3 Select “OPT” and press .

• AUTO: Preferentially output the sound
signal from the HDMI SAT/
CATV input jack.

• OPT: Output the signal from the SAT/
CATV OPT IN jack.

Changing the brightness of
the front panel display
(DIMMER)

Enjoying the sound at low
volume (NIGHT MODE)

You can enjoy sound effects and hear the dialog
clearly even at a low volume level using this
function.

1 Select “AUDIO” in the AMP menu, then

press or c.

2 Select “NIGHT MODE,” then press

or c.

3 Select the setting and press .

• ON: Turns on the “NIGHT MODE”
function.

• OFF: Turns off the function.

Tip

• You can listen to Dolby Digital sound at low volume
by using AUDIO DRC (page 31).

US

32

The brightness of the front panel display can be
set to one of 2 levels.

1 Select “SYSTEM” in the AMP menu,

then press or c.

2 Select “DIMMER,” then press or c.
3 Select the setting and press .

• ON: Dim.

•OFF:Bright.

Changing the display setting
(DISPLAY)

You can change the display behavior of the front
panel display.

1 Select “SYSTEM” in the AMP menu,

then press or c.

2 Select “ DISPLAY,” then press or c.
3 Select the setting and press .

• ON: The display stays turned on.

• OFF: The display appears for a few

seconds when you operate the
system.

Tip

• The display shows the kinds of input signal (digital
input only) when you press DISPLAY, even if you set
“DISPLAY” to “OFF.”

Note

• The display stays turned on when the muting or
protection function is working, even if you set
“DISPLAY” to “OFF.”

Using the sleep timer (SLEEP)

You can set the system to turn off at a preset time
when you want to fall asleep listening to music.
You can preset the time in 10-minute increments.

1 Select “SYSTEM” in the AMP menu,

then press or c.

2 Select “SLEEP,” then press or c.
3 Select the preset time you want and

press .

The minutes display (remaining time)
changes as follows:

Auto Standby function (AUTO
STBY)

You can reduce power consumption. The system
enters standby mode automatically when you do
not operate the system for about 30 minutes and
the system is not outputting sound for about 30
minutes.
The default setting is “ON”.

1 Select “SYSTEM” in the AMP menu,

then press or c.

2 Select “AUTO STBY,” then press or

c.

3 Select the setting and press .

• ON: Turns on the “AUTO STBY”
function.

• OFF: Turns off the function.

Notes

• When the system is turned off via the AUTO STBY
function, the system may not be turned on
automatically when you turn on the TV next time.

• “AUTO STBY” begins to flash in the front panel
display about two minutes before the system enters
standby mode.

Advanced Settings

OFF y 10M y 20M

YY

90M y 80M ... 30M

Note

• This function is only for this system, not for the
connected TV or other components.

33

US

Additional Information

Troubleshooting

If you experience any of the following
difficulties while using the system, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should any
problem persist, consult your nearest Sony
dealer.

POWER

The power is not turned on.

• Check that the AC power cord (mains lead)
is connected securely.

The system is not turned on when the TV is
turned on.

• Check the TV speaker settings. The TV
speaker settings control how the system is
automatically turned on with the TV. To
enjoy the TV sound via the system, you need
to set the speaker settings of the TV to output
the sound from external audio equipment.
For details, refer to the operating
instructions of the TV.

• The system is not turned on when you turn
the TV on if sound was being output from
the TV speakers the last time the TV was
turned off.

The System Power Off function does not work.

• Change the setting of the TV to turn
connected components off automatically
when you turn off the TV. For details, refer
to the operating instructions of the TV.

The system is turned off when you turn off the
TV.

• When the Control for HDMI function is on,
the System Power Off function is active, and
the system is turned off when you turn off
the TV.

The system is turned off automatically.

• The AUTO STBY function is working
(page 33).

SOUND

Dolby Digital or DTS multi-channel sound is
not reproduced.

• Check that the Blu-ray Disc, DVD, etc., is
recorded in Dolby Digital or DTS format.

• When connecting the Blu-ray Disc, DVD
player, etc., to the digital input jacks of this
system, check the audio setting (settings for
the audio output) of the connected
component.

The surround effect cannot be obtained.

• Depending on the digital signal, the
surround processing may not work (page

19). Press DISPLAY to show the sound
format in the front panel display. If “2.0CH”
or “1.0CH” is displayed in the front panel
display, the signal is stereo or monaural and
does not include multi-channel sound. If
“5.1CH,” etc., is displayed, the signal
contains multiple channels, but the surround
effect may be subtle depending on the
program or disc.

No TV sound is output from the system.

• Check the connection of the digital optical
cord or audio cord that is connected to the
system and the TV (page 10).

• Check the sound output of the TV.

• If the TV is compatible with the ARC
function, set “CTRL HDMI” and “ARC” to
“ON.”

The sound is output from both the system and
the TV.

• If the Control for HDMI function is set to
off, or the selected component is not
compatible with the Control for HDMI
function, turn off the sound of the system or
the TV.

Sound lags behind the TV image.

• Set “A/V SYNC” to “OFF” if “A/V SYNC”
is set to “ON.”

The volume turns down when the output
method changes from the TV speaker to the
system speakers.

• The Volume Limit function is working. For
details, see “Using the Volume Limit
function” (page 22).

34

US

No sound or only a very low-level sound of the
connected component is heard from the
system.

• Press MASTER VOL + and check the
volume level.

• Press MUTING or MASTER VOL + to
cancel the muting function.

• Check that the input source is correctly
selected.

• Check that all the cables and cords of the
system and the connected components are
fully inserted.

• Check the HDMI setting of the connected
components.

No sound is output from specific speakers.

• Check that the connectors of the speaker
cord are fully inserted into the jacks.

• Depending on the sound source that is input
to the system or selected sound field of the
system (page 19), no sound is output from
the center speaker.

Sound is interrupted or there is noise.

• Check “Formats supported by this system”
(page 36).

IMAGE

No image appears on the TV.

• Check that the TV and the system are
connected correctly.

• Check that the TV is selected correctly.

• Set the TV to the appropriate input mode.

• Check whether HDMI IN and HDMI OUT
are connected in reverse.

• Check that the cords are fully inserted into
the jacks on both the component and this
system (pages 10, 12).

No 3D image appears on the TV.

• Depending on the TV or the video
component, 3D images may not be
displayed. Check the 3D image formats
supported by the system (page 37).

When the system is in standby mode, there is
no image or sound on the TV.

• “CTRL HDMI” is set to “OFF.”

• When the system is in standby mode, image
and sound are output from the HDMI
component selected the last time you turned
off the system. If you want to play a
component other than the HDMI component
you selected last time, play the component
via One-Touch Play, or turn on the system to
select the HDMI component you want to
enjoy.

• Make sure “PASS THRU” is set to “ON” in
the AMP menu if you connect components
not compatible with “BRAVIA” Sync to the
system (page 23).

The remote does not function

• Point the remote at the remote sensor on
the system.

• Remove any obstacles in the path between
the remote and the system.

• Replace both batteries in the remote with
new ones, if they are weak.

• Make sure you select the correct input on the
remote.

OTHER

Control for HDMI does not work properly.

• Check the HDMI connection (pages 10).

• Set up Control for HDMI on the TV (page

20).

• Make sure the connected component is
compatible with “BRAVIA” Sync.

• Check the Control for HDMI settings on the
connected component. Refer to the
operating instructions supplied of the
connected component.

• If you change the HDMI connection,
connect/disconnect the AC power cord
(mains lead), or if there is a power failure,
repeat the procedures of ““BRAVIA” Sync
Features” (page 20).

• When you plug in or unplug the AC power
cord (mains lead), wait 15 seconds or more
before operating the system.

Additional Information

continued

35

US

• If you connect the audio output of the video
component and the system using other than
an HDMI cable, no sound may be output
because of “BRAVIA” Sync. In this case, set
“CTRL HDMI” to “OFF” (page 21) or
connect the audio output jack directly to the
TV instead of the system.

If “PROTECTOR” and “PUSH POWER” appear
alternately in the front panel display.

Press ?/1 to turn off the system, and check
the following item after “STANDBY”
disappears.

• Is anything blocking the ventilation holes of
the system?
After checking the above item and fixing
any problems, turn on the system. If the
cause of the problem cannot be found even
after checking the above item, consult your
nearest Sony dealer.

If the system still does not
operate properly after performing
the above measures, reset the
system as follows:

Use buttons on the system for the operation.

1 Press ?/1 to turn on the power.
2 Press ?/1 while pressing INPUT

SELECTOR and VOLUME –.

“COLD RESET” appears and the system is
reset. AMP menu, sound field, etc., return to
the default settings.

Specifications

Formats supported by this
system

Digital input formats supported by this system
are as follows.

Format Supported/Not supported

Dolby Digital a
DTS a
Linear PCM (2ch)* a

Linear PCM (5.1ch,

7.1ch)* (Only on
HDMI)

Dolby Digital Plus ×

Dolby True HD ×

DTS-HD ×

* Linear PCM accepts sampling frequencies of no

more than 48 kHz.

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
for the U.S. model
Front L + Front R: With 4 ohms loads, both

channels driven, from 1 80 ­20,000 Hz; rated 50 Watts
per channel minimum R MS
power, with no more than 1
% total harmonic distortion
from 250 milli watts to
rated output.

a

36

Amplifier section

U.S. models:
POWER OUTPUT (reference)
Front L/Front R/Center: 85 W (per channel at

4 ohms, 1 kHz)
Subwoofer: 85 W (at 4 ohms, 100 Hz)
Canadian models:
POWER OUTPUT (rated)
Front L/Front R: 60 W + 60 W (at 4 ohms,

1 kHz, 1 % THD)
POWER OUTPUT (reference)
Front L/Front R/Center: 85 W (per channel at

4 ohms, 1 kHz)
Subwoofer: 85 W (at 4 ohms, 100 Hz)

US

Inputs
TV, SA-CD/CD Analog
TV, SAT/CATV Digital (Optical)
VIDEO Digital (Coaxial)

Dimensions (approx.) 800 mm × 66 mm × 60 mm

1

(31

/2 in × 2 5/8 in ×

3

/8 in) (w/h/d)

2

Mass (approx.) 1.3 kg (2 lb 14 oz)

HDMI section

Connector HDMI™ connector
Video inputs/outputs BD, DVD, SAT/CATV;

640 × 480p@60 Hz
720 × 480p@59.94/60 Hz
1280 × 720p@59.94/60 Hz
1920 × 1080i@59.94/60 Hz
1920 × 1080p@59.94/60 Hz
720 × 576p@50 Hz
1280 × 720p@50 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz

Video inputs/outputs (3D) BD, DVD, SAT/CATV;

1280 × 720p@59.94/60 Hz
Frame packing
1920 × 1080i@59.94/60 Hz
Frame packing
1920 × 1080i@59.94/60 Hz
Side-by-Side (Half)
1920 × 1080p@59.94/60 Hz
Side-by-Side (Half)
1280 × 720p@50 Hz
Frame packing
1920 × 1080i@50 Hz
Frame packing
1920 × 1080i@50 Hz
Side-by-Side (Half)
1920 × 1080p@50 Hz
Side-by-Side (Half)
1920 × 1080p@24 Hz
Frame packing

Audio inputs BD, DVD, SAT/CATV:

Linear PCM 7.1ch/
Dolby Digital/DTS

Subwoofer (SA-WCT150)

Speaker system Subwoofer, Bass reflex
Speaker unit 130 mm (5

1

Rated impedance 4 ohms
Dimensions (approx.) 196 mm × 450 mm ×

1

/4 in)

3

410 mm (7
× 16
(w/h/d)

Mass (approx.) 10.5 kg (23 lb 3 oz)

General

Power requirements 120 V AC, 60 Hz
Power consumption

On: 75 Watts
Standby mode: 0.3 W or less (Co ntrol for HDMI

is off)
Power output
(DIGITAL MEDIA PORT) DC OUT: 5 V, 700 mA

Design and specifi cations are subject t o change without
notice.

• Standby power consumption 0.3 W or less.

• Halogenated flame retardants are not used in the
certain printed wiring boards.

• Over 85 % power efficiency of amplifier block is
achieved with the full digital amplifier, S-Master.

/8 in) cone type

/4 in × 17 3/4 in

Additional Information

Speaker (SS-CT150)

Front speaker unit
Speaker system Full range, Bass reflex
Speaker units 50 mm × 90 mm (2 in ×

5

/8 in) cone type

3
Rated impedance 4 ohms
Center speaker unit
Speaker system Full range, Bass reflex
Speaker units 50 mm × 90 mm (2 in ×

5

/8 in) cone type

3
Rated impedance 4 ohms

37

US

Index

A

A/V SYNC 31
AMP menu
ARC
AUDIO DRC
AUTO S TBY

30

11, 24

31
33

B

BASS 31
“BRAVIA” Sync

20

C

CNT LEVEL 31
Connecting

Blu-ray Disc player 10
cable television tuner
DIGITAL MEDIA PORT adapter
DVD player
PlayStation 2
PlayStation 3
satellite tuner

10

TV

10, 12

10, 12

12
11
10, 12

D

Digital optical cord 10
DIMMER
DISPLAY
DUAL MONO

32
33

32

12

N

NIGHT MODE 32

P

PROTECTOR 36

R

Remote

before use
operating

6

16, 25

S

Sleep timer 33
Sound field
SW LEVEL

19

31

T

TREBLE 31

V

VOLUME 14, 16
Volume Limit function

22

F

Front panel display 15

I

INPUT MODE 32
INPUT SELECTOR

M

Muting 16

US

38

14