Sony HMZT3W User Manual
1
Connect playback equipment and a TV to the
processor unit.
Head Mounted Display
Startup Guide
You can watch video from playback equipment on the
TV by connecting the TV to the processor unit with a
High-Speed HDMI cable.
In such a case, set “HDMI pass-through” in “General
Setup” to “On.”
Note
HDMI pass-through does
not enable simultaneous
video playback on the head
mounted unit and TV.
Blu-ray Disc™ player
2
Connect headphones.
HDMI cable (supplied)
Game console
Connect the miniplug of the
headphones to the headphone
jack.
Processor unit (Rear)
HDMI IN
TV
HDMI OUT
(TV)
HDMI cable
(sold separately)
Before use, also refer to “Health Precautions” and “Precautions”
in the “Reference Guide.”
HMZ-T3W
Printed using VOC (Volatile Organic Compound)-free
vegetable based ink.
© 2013 Sony Corporation Printed in Japan
4-471-975-11(1)
3
Connect the large AC adaptor and the AC power
cord to the processor unit.
Processor unit
(Rear)
AC power cord
(mains lead)
(supplied)
4
Turn the system on.
1. Turn the processor unit on.
2. Turn the head mounted
unit on.
AC adaptor
(large) (supplied)
To wall outlet
1 Connect
Prepare the following items included in the box.
Head mounted unit
and battery unit (1)
AC adaptor (small)
(AC-UD10) (1)
Before use, charge the battery.
Charging starts when the small AC adaptor and the AC power cord are
connected to the battery unit.
The (power) indicator is lit in orange during charging, and it goes dark
when charging is complete.
Processor unit (1) Headphones (1) HDMI cable (1) Micro USB cable (1)
AC adaptor (large)
(AC-L200D) (1)
Micro USB cable
(supplied)
AC power cord
(mains lead) (2)
AC adaptor (small)
(supplied)
AC power cord (mains
lead) (supplied)
5
Turn the playback equipment on.
6
Select the input.
Press the INPUT button on the
processor unit to select the input
for the source equipment. The HDMI
INPUT indicator of the selected input
will light in orange.
7
Adjust the orientation of the battery unit and
confirm that the WIRELESS indicator lights in
blue.
Notes
The radio waves may not be
received properly, depending
on the orientation of the battery
unit. Use the battery unit with the
SONY logo side up.
Use where there are no
obstructions between the
processor unit and the battery
unit.
Communication distance:
Approx. 5 m
Battery unit
Head mounted unit
To wall outlet
Tips
You can use the system while
charging, with the AC power cord
connected to the power source.
It will take about 5 hours to fully
charge the battery, when the
system is turned off.
Continued in 2 Adjust and Wear
2 Adjust and Wear
3
Set Up and View
Follow the instructions
displayed on the
screen for operations.
For a Comfortable Fit
Battery unit
Screen
Support the unit with your forehead and at two positions
on the back of your head.
Do not rest it on your nose.
Adjust the unit so that the screens are in front of your eyes.
Place the battery unit in a stable position.
Eye
Screen
1
Select a display language
(first time only).
Press the / button to
select a language, and then
press the MENU or button.
2
Adjust the lens span.
Slide each lens span adjuster until you can
see both screens clearly.
After adjustment, press the MENU button or
button.
Tips
If you cannot see the screen clearly after lens span adjustment,
start over from “2 Adjust and Wear.”
If adjustment is difficult, try sliding both adjusters to the center
position before adjustment.
If you normally wear glasses or contact lenses, wear them as usual during
use (with the exception of reading glasses). Note that watching with bifocals
may be less than optimal.
1
Raise the top headband
and the forehead
supporter.
The position of the forehead supporter is
adjustable.
The lowest position is standard.
2
To loosen
Pull out the straps of
the top and bottom
To tighten
headbands.
Hold down the button on the upper side of
each adjuster and pull out the strap on the
right.
All three “ ” marks
and the horizontal
line intersect.
One or more “ ”
marks and the
horizontal line do
not intersect.
3
Check display alignment.
Confirm that all three “ ” marks and the
horizontal line intersect then press the MENU
or button.
It is acceptable if the “
horizontal line intersect in a position other
than the center of the screen.
Note
The “ ” marks and the horizontal line do not intersect if the
position of the head mounted unit is shifted. Readjust the
length of the headbands and confirm the position, referring to
“2 Adjust and Wear” and “ Adjust the lens span.”
If even one of the “
intersect, refer to “Confirming Screen Alignment” of the
“Reference Guide.”
” marks and the horizontal line do not
” marks and the
3
Put the head mounted unit
on your head.
Lower the bottom headband to the base of
your head.
4
Tighten the headbands
loosely and adjust the
position of the head
mounted unit.
Push the strap into the adjuster on the top
and bottom headbands to fix the head
mounted unit.
Carefully adjust the unit left, right, up, and
down to find the best position for viewing
the centers of the screens.
4
Follow the instructions
displayed on the screen.
Refer to the information on the screen for
operation.
5
Operate the playback
equipment.
The picture appears on the screen of the
head mounted unit.
Tips
Adjust the volume using the VOL +/– button on the head
mounted unit.
It is useful to keep the remote control unit for the playback
equipment at hand.
Some functions of the playback equipment can be controlled
from this system. For details refer to “Control for HDMI” in
“General Setup” of the “Reference Guide.”
5
Tighten the headbands
securely.
6
Put on the headphones.
When you wear glasses or need further adjustment
Refer to “Fitting the Head Mounted Unit” of the “Reference Guide.”
Resolving lack of audio, video, or 3D playback
1. Turn on the processor unit and the head mounted unit.
2. Turn the playback equipment off then back on.
If the playback equipment is a PlayStation®3, turn it off then
hold down the power button on the PlayStation®3 for at least 5
seconds (until you hear another beep) to restart it.
“PlayStation” is a registered trademark of Sony Computer Entertainment Inc.
Loading...