Page 1
RGB SQ PROCESSOR BOARD
HKSR-5803SQ
ADVANCED HQ PROCESSOR BOARD
HKSR-5803HQ
INSTALLATION MANUAL
1st Edition
Page 2
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HKSR-5803SQ/5803HQ
Page 3
Section 1
Installation
Purpose of this manual
This manual is an installation manual of RGB SQ Processor Board HKSR-5803SQ and Advanced HQ Processor
Board HKSR-5803HQ.
This manual is intended for system and service engineers,
so describes information regarding installation.
Related manual
Besides this installation manual, the following manual is
available for HKSR-5803SQ and HKSR-5803HQ.
. Maintenance Manual (available on request)
This manual describes the information for the maintenance of this unit and the information that premises the
parts level service.
If this information is required, please contact your local
Sony Sales Office/Service Center.
1-1. Specifications
1-2. Installation Overview
Components
HKSR-5803SQ is composed of the following items:
. SQ-20 Board
. Hexagonal support 7 mm (4 pcs)
. PSW2.6 x 5.8 (8 pcs)
. Installation manual
HKSR-5803HQ is composed of the following items:
. DLP-27 Board
. Hexagonal support 7 mm (4 pcs)
. PSW2.6 x 5.8 (8 pcs)
. Installation manual
Applicable models
SRW-5800
Installations of HKSR-5803SQ or HKSR-5803HQ
General
HKSR-5803SQ
Dimensions (w/h)
SQ-20 Board: 155 x 90 mm
Mass SQ-20 Board: approx. 70 g
Power requirements +3.3 V dc: 840 mA
+1.5 V dc: 1800 mA
Power consumption approx. 5.5 W
HKSR-5803HQ
Dimensions (w/h)
DLP-27 Board: 155 x 90 mm
Mass DLP-27 Board: approx. 70 g
Power requirements +3.3 V dc 850 mA
+1.5 V dc: 1800 mA
Power consumption approx. 5.5 W
The HKSR-5803SQ comprises the SQ-20 board.
Mount the SQ-20 board on the HPR-22 board.
The HKSR-5803HQ comprises the DLP-27 board.
Mount the DLP-27 board on the HPR-22 board.
Attach and adjust the HKSR-5803SQ or HKSR-5803HQ
properly, following the procedures in Section 1-3 and later.
HKSR-5803SQ/5803HQ
1-1 (E)
Page 4
1-3. Installation Procedure
1. Turn off the power of the VTR.
2. Fully loosen the two fixing screws, and then slide the
two knobs on the upper lid (front) assembly each to the
inside. (Move the knobs to the outside to fix the upper
lid (front) assembly.)
3. Remove the upper lid (front) assembly in the arrow
direction.
4. Fully loosen the two fixing screws, and then remove
the upper lid (rear) assembly in the arrow direction.
Fixing screw
Upper lid (rear)
assembly
Protrusion
Fixing screw
Fixing screw
Knob
Upper lid (front) assembly
Knob
Removal
Installation
Square hole
5. Raise the eject levers of the HPR-22 board in the
arrow direction, and then pull out the board slowly
upward.
Eject lever
HPR-22 board
Eject lever
1-2 (E)
HKSR-5803SQ/5803HQ
Page 5
6. Remove the six screws to detach the shield plate from
the HPR-22 board.
9. Reattach the shield plate to the HIF-22 board with six
screws.
Shield plate
PSW
2.6 x 6
PSW
2.6 x 6
HPR-22 board
PSW2.6 x 6
7. Attach four 7 mm hexagonal supports (accessory) to
the HPR-22 board with four screws (accessory).
8. Connect the SQ-20 board or DLP-27 board to the
HPR-22 board and secure it with four screws (accessory).
Shield plate
PSW
2.6 x 6
HPR-22 board
PSW
2.6 x 6
PSW2.6 x 6
PSW2.6 x 5.8
(Supplied accessory)
PSW2.6 x 5.8
(Supplied
accessory)
Hexagonal
supports (7 mm)
(Supplied
accessory)
SQ-20 board
or
DLP-27 board
HPR-22 board
Hexagonal
supports (7 mm)
(Supplied
accessory)
PSW2.6 x 5.8
(Supplied
accessory)
PSW2.6 x 5.8
(Supplied
accessory)
HKSR-5803SQ/5803HQ
1-3 (E)
Page 6
10. Securely insert the HPR-22 board into the “HPR” slot
to tightly connect the board to the connector on the
motherboard, while pressing down the two eject
levers.
1-4. Confirming Identification of
Optional Board
Confirmation Procedure
Eject lever
HPR-22 board
Eject lever
SS
APR
FC
DVP
HIF
MY
HPR
EQ
HPR-22 board
1. On the HOME menu, press the DIAG button while
pressing the [SFT] (shift) key.
The MAINTENANCE INFORMATION menu
appears.
F1
F2
F3
F4
DIAG
ALT
ROM
OPTION
MAINTENANCE INFORMATION DISPLAY
VER
OPERATION 1105HOURS[ 1105H]
ERR
DRUM RUNNING
LOG
TAPE HOURS
THREADING 4048TIMES[
INF
F5
F6 F7 F8 F9
238HOURS[ 238H]
153HOURS[ 153H]
MAINTE
EXEC
EXIT
F10
4048T]
2. Press [F5] (OPTION INF).
The OPTION INFORMATION menu appears.
F1
F2
F3
F4
DIAG
ALT
OPTION INFO
OPTION BOARD INFORMATION
HKSR-5001 Board –––––––––
HKSR-5802 Board –––––––––
HKSR-5803 Board
FUNC
INFO
F5
F6 F7 F8 F9
INSTALLED (SQ)
EXIT
F10
1-4 (E)
<Top view>
3. Check that “INSTALLED (SQ)” (HKSR-5803SQ) or
“INSTALLED (HQ)” (HKSR-5803HQ) is displayed
for the HKSR-5803 board.
n
For more information on the maintenance mode, refer to
Section 3 of the VTR Maintenance Manual Volume 1.
HKSR-5803SQ/5803HQ
Page 7
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
HKSR-5803SQ/5803HQ
Page 8
HKSR-5803SQ (SY)
HKSR-5803HQ (SY) J, E
3-286-478-01
Printed in Japan
Sony Corporation 2007. 10 08
©2007
Loading...