MAINTENANCE MANUAL
1st Edition (Revised 2)
Serial No. 10001 and Higher
Page 2
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
HKDV-900
Page 3
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
This is the maintenance manual of the HD Digital Video Controller HKDV-900.
This manual is intended for use by service engineers, and describes how to maintain
the unit, and contains information on primary services (removing the boards, selfdiagnostics, troubleshooting, parts list, semiconductor pin assignments, block
diagram, schematic diagrams and board layouts).
Beside this Maintenance Manual, the following manuals are available for the unit:
..
. Operation Manual (Supplied with the unit)
..
This manual describes the precautions during operation of the unit and describes
each block.
Part number: 3-204-566-0X
..
. Installation Manual (Supplied with the unit)
..
This manual describes the operating environment, power supply, installation
space, matching cables, signal inputs/outputs, setting the switches on board and
rack mounting.
Part number: 3-204-595-0X
..
. “Semiconductor Pin Assignments” CD-ROM (Available on request)
..
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual for the corresponding unit. The maintenance manual contains
a complete list of all semiconductors and their ID Nos., and thus should be used
together with the CD-ROM.
Part number: 9-968-546-XX
HKDV-900
3 (E)
Page 6
Contents
The following is a summary of all the sections of this manual.
Section 1Service Overview
Contains the location of the main parts, and describes how to remove/reinstall the
cabinets and boards, replace the rotary encoder, switching regulator, and NV-RAM.
Section 2Troubleshooting
Explains the self-diagnostics and troubleshooting.
Section 3Spare Parts
Contains the exploded view and the spare parts list.
Section 4Semiconductor Pin Assignments
Contains information on semiconductors used for the unit.
It includes a complete list of the semiconductors and their ID Nos. for retrieving
information on “Semiconductor Pin Assignments” CD-ROM, which is available
separately.
Please refer to this section together with the “Semiconductor Pin Assignments” CDROM.
Information on the semiconductors not contained in the CD-ROM at the time of
issue of this manual, if any, is given in this section as well.
Section 5Block Diagram
Contains the overall block diagram.
Section 6Schematic Diagrams
Contains the schematic diagrams for mounted circuit boards.
Section 7Board Layouts
Contains the board layouts for mounted circuit boards.
4 (E)
HKDV-900
Page 7
1-1.Main Parts Layouts
Switching regulator
CP-365 board
2
Section 1
Service Overview
Rotary encoder
No.Board nameFunction
1CP-364 boardCPU and Volume Board
2CP-365 board7SEG LED and Switch Board
CP-364 board
2
HKDV-900
1-1 (E)
Page 8
1-2. Removing/Reinstalling the Cabinets
1-2.Removing/Reinstalling the Cabinets
1-2-1. Top Panel
1. Remove the three screws, and then remove the top
panel in the direction of the arrow.
PSW3 x 6
Top panel
1-2-2. Front Panel
1. Remove the top panel. (Refer to Section 1-2-1.)
2. Remove the eight knobs.
3. Remove the four screws (PSW4 x 10) to remove the
right and left rack angles.
4. Remove the two screws (PSW3 x 6), and then remove
the front panel in the direction of the arrow.
PSW4 x 10
Rack angle
PSW3 x 6
Front panel
2. Re-attach the top panel in reverse order of step 1.
PSW3 x 6
Knob
Rack angle
PSW
4 x 10
5. Re-attach the front panel in reverse order of steps 2
to 4.
1-2 (E)
HKDV-900
Page 9
PSW
4 x 8
AC inlet
Harness
(white)
Harness
(green +
yellow)
Harness (brown)
AC inlet
Terminal cover
Terminal block
B
A
1-3. Removing/Reinstalling the Boards
1-3.Removing/Reinstalling the Boards
1-3-1. CP-365 Board
1. Remove the top panel. (Refer to Section 1-2-1.)
2. Remove the front panel. (Refer to Section 1-2-2.)
3. Insert a flat screwdriver into the groove of the connectors (CN1 and CN2), push it to the front (Fig. 1) and
disconnect the harnesses from the connectors. (Fig. 2)
4. Remove the five screws to remove the CP-365 board.
n
Be careful not to drop the isolating plate because it is
not fixed.
Flat screwdriver
Fig.1
Harness
Groove
Connector
Fig.2
1-3-2. CP-364 Board
1. Remove the top panel. (Refer to Section 1-2-1.)
2. Remove the front panel. (Refer to Section 1-2-2.)
3. Remove the CP-365 board. (Refer to Section 1-3-1.)
4. Disconnect the harnesses from the connectors (CN402
to CN409) on the CP-364 board.
5. Remove the two screws which fixing the power
switch.
6. Remove the five screws, and then remove the holder
assembly in the direction of the arrow.
Power switch
PSW3 x 6
CP-364 board
CN402 to CN409
PSW3 x 6
PSW3 x 6
Connector
(CN2)
Connector
(CN1)
PSW3 x 6
CP-365 board
Isolating plate
5. Re-attach the CP-365 board in reverse order of steps 3
and 4.
6. After replacing the CP-365 board, execute the self
diagnostic tests. (Refer to Section 2-2, “Self Diagnostic Mode”.)
Holder assembly
PSW3 x 6
7. Remove the screw to remove the harnesses (green +
yellow).
8. Disconnect the two harnesses (white and brown) from
the AC inlet.
n
Slide the terminal cover in the direction of arrow A, and
then pull the terminal block out in the direction of arrow B.
HKDV-900
1-3 (E)
Page 10
1-3. Removing/Reinstalling the Boards
1-4. Replacing the Rotary Encoder
9. Remove the eight hexagon screws.
10. Remove the six screws (PSW3 x 6) to remove the CP-
364 board.
n
The SW cap is not a component of the CP-364 board.
When replacing the CP-364 board, remove the SW cap
and reuse it.
Power switch
SW cap
PSW3 x 6
CP-364 board
PSW3 x 6
Hexagon
screws
1-4.Replacing the Rotary Encoder
1. Remove the CP-365 board. (Refer to Section 1-3-1.)
2. Disconnect the harnesses from the connectors (CN402
to CN409) on the CP-364 board.
3. Remove the two screws which fixing the power
switch.
4. Remove the five screws, and then remove the holder
assembly in the direction of the arrow.
Power switch
PSW3 x 6
CP-364 board
CN402 to CN409
PSW3 x 6
PSW3 x 6
Holder assembly
PSW3 x 6
11. Re-attach the CP-364 board in reverse order of steps 4
to 10.
12. After replacing the CP-364 board, check the NV-RAM
and execute the self diagnostic test. (Refer to Sections
1-6, “Replacing the NV-RAMs”, 2-2, “Self Diagnostic
Mode”.)
5. Remove the hexagon nut and washer to remove the
replacing rotary encoder from the holder assembly.
Holder assembly
Rotary encoder
Washer
Hexagon nut
6. Attach a new rotary encoder in reverse order of steps 2
to 5.
7. After replacing the rotary encoder, execute the self
diagnostic test. (Refer to Section 2-2, “Self Diagnostic
Mode”.)
1-4 (E)
HKDV-900
Page 11
1-5. Replacing the Switching Regulator
1-6. Replacing the NV-RAMs
1-5.Replacing the Switching Regulator
w
. The switching regulator is a critical part to safety.
Replacing parts other than the specified switching
regulator may result in a fire or electrical shock.
. The switching regulator is used in the unit.
Before replacement, turn off the power switch, disconnect the plug from the outlet, and wait for one minute at
least.
If touching the switching regulator soon after turning off
the power switch, an electric shock may be caused.
Replacement Part
Part name : Switching regulator
Part No. : ! 1-413-917-12
1. Remove the CP-364 board. (Refer to Section 1-3-2.)
2. Remove the seven screws (PSW4 x 8) from the
switching regulator to disconnect the harnesses
(white : one, brown : one, green + yellow : one,
black : two, red : two).
3. Remove the two screws (PSW3 x 6) to remove the
switching regulator from the CP-364 board.
Harness (white)
Harness
(brown)
PSW4 x 8
4. Attach a new switching regulator in reverse order of
steps 2 and 3.
5. After replacing the switching regulator, execute the
self diagnostic test. (Refer to Section 2-2, “Self
Diagnostic Mode”.)
HKDV-900
Harness (green + yellow)
Harness (black)
Harnesses (red)
Switching regulator
CP-364 board
PSW3 x 6
1-6.Replacing the NV-RAMs
The two NV-RAMs which have the ID to make CPU
identify the each NV-RAM and customized data (adjustment state of each output signal and setting value) are used
in the CP-364 board. When one of the NV-RAMs is
replaced, these data will be lost.
Ref. No.(Address)Contents of holding data
IC201(G-1/CP-364)ID, adjustment state of each
output signal and setting value
(user set value)
IC203(F-1/CP-364)
Adjustment/Re-setting after Replacing the NVRAM
When replacing one of NV-RAMs, adjust and re-set the
data following steps below.
n
Even if either of the NV-RAMs is replaced, be sure to
follow the steps below.
1. Turn off the power switch.
2. Remove the top panel. (Refer to Section 1-2-1.)
3. Set switches S100-7 and S100-8 (J-3) on the CP-364
board to ON.
4. Set the power switch to ON.
After all of the LEDs on the front panel are lit on and
off, confirm that the 7-segment LED indicates “99”,
“88”, “77”, “66”, “55”, “44”, “33”, “22”, “11” and
“00” with interval of 0.5 seconds in this order, and
finally indicates “01”.
5. Turn off the power switch.
6. While pressing the “CANCEL” button on the front
panel, set the power switch to ON. Confirm that the 7segment LED indicates “99”, “88” to “11” and “00”
with interval of 0.5 seconds in this order. Then the
indication is repeated starting from “01”, “02” to “FE”,“FF” several times and finally indicates “01” and
finally indicates “01”.
n
Keep pressing the “CANCEL” button until all of the
above countdown indications are completed.
7. When the 7-segment LED display indicates “01”, turn
off the power switch.
8. Set the switches of S100-7 and S100-8 (J-3) to OFF.
9. Re-set and customize the data as original.
For the details of the setting procedure, refer to the
sections of “Output Signal Adjustment” and “Saving
and Recalling Adjustments and Settings” in the
Operation Manual.
1-5 (E)
Page 12
Page 13
Section 2
Troubleshooting
2-1.Normal Diagnostic Function (Power
ON Test)
This unit executes the tests below automatically when
turning the power ON.
1. ROM (IC103 on the CP-364 board) test
(Error : “E0”)
This performs a ROM checksum test.
The “E0” display blinks on the 7SEG LED and the
operation stops when an error occurs. Replace the
ROM.
2. RAM (IC104 on the CP-364 board) test
(Error : “E1”)
This performs a RAM read/write test (in which cycle
data “00” through “FF”, “FF” and “00” are written
and read for comparison).
The “E1” display blinks on the 7SEG LED and the
operation stops when an error occurs. Replace the
RAM.
3.
NV-RAM (IC201, 203 on the CP-364 board) test
(Error :
This performs an NV-RAM read/write test (in which
data “FF” and “00” are written and read for comparison). But the data of the memory does not change.
The “E2” display blinks on the 7SEG LED and the
operation stops when an error occurs. Replace the
NV-RAM.
“E2”
)
2-2.Self Diagnostic Mode
This unit allows executing the nine self diagnostic tests
below. (Refer to Section 2-2-3, “Starting and Quitting of
the Self Diagnostic Mode”.)
1. ROM version display
Displays the current ROM version on the 7SEG LED.
2. ROM test
Performs a ROM checksum test to check the memory
operation.
3. RAM test
Performs a RAM read/write test to check the memory
operation.
4. NV-RAM test
Performs an NV-RAM read/write test to check the
memory operation.
5. LED test
Checks that all the LEDs light.
6. 7SEG LED test
Performs a 7SEG LED light test to check the decoding
operation for numeric display.
7. Switch test
Checks the operation of a pushbutton switch.
4. NV-RAM (IC201, 203 on the CP-364 board)
checksum test (Error : “E3”)
This performs an NV-RAM checksum test.
The “E3” display blinks on the 7SEG LED and the
operation stops when an error occurs. Replace the
NV-RAM.
5. Switch short test (Error : “EE”)
This test confirms that a switch is not short-circuited.
If the switch is short-circuited, the LED of the switch
blinks and the “EE” display blinks on the 7SEG LED
and the operation stops. Replace the short-circuited
switch.
HKDV-900
8. Rotary encoder test
Checks the operation of a rotary encoder.
9. RS-422A test
Performs an RS-422A loop-back test to check the
communication operation.
2-1 (E)
Page 14
2-2. Self Diagnostic Mode
2-2-1. Required Tool
1. Connector tool for RS-422A test
In 2-2-5. “ 9. RS-422A test” of a self diagnostic test, the four connector tools below are required.
n
If all the four connector tools are not used, the RS-422A test is possible.
D-sub 9-pin connector (male) whose pins 2 and 8, and pins 3 and 7 were connected (Other pins are
opened.)
Pin No.Signal name
1
2
3
4
5
6
7
8
9
GND
REM TY
REM RX
GND
_
GND
REM TX
REM RY
GND
[D-sub 9-pin . MALE]
1
5
96
_ EXT VIEW _
n
The HKDV-900 before modification uses the D-sub 15-pin connector.
D-sub 15-pin connector (male) whose pins 7 and 8, and pins 14 and 15 were connected (Other pins are
opened.)
Pin No.Signal name
1
2, 3
4
5, 6
7
8
9-13
14
15
FRAME G
_
REM G
_
REM TX
REM RX
_
REM TY
REM RY
[D-sub 15-pin . MALE]
1
8
159
_ EXT VIEW _
2-2-2. Location of Knobs and Buttons on the Front Panel
The knobs and buttons described in this section are located as shown below:
MASTERYPBPRSETUP SYNC PHASE FINE_
UNITYUNITYUNITYUNITYUNITYPRESET PRESET PRESET
SQUEEZE
LETTER
BOX
Rotary encoder
LED bulit-in pushbutton switch
Level LED
2-2 (E)
POWER
IMAGE ENHANCER
HD
D1 D2INPUT
CONTROL
SELECT
LED bulit-in
pushbutton
switch
7SEG LED
_
OUTPUT
Pushbutton
switches
+
CANCEL
STORE
LOAD
CROP
LED bulit-in
pushbutton
switch
HKDV-900
Page 15
2-2. Self Diagnostic Mode
2-2-3. Starting and Quitting of the Self
Diagnostic Mode
n
After replacing a NV-RAM, the self diagnostic mode
needs to be started up for writing the ID. For more details,
refer to Section 1-6, “Replacing the NV-RAMs”.
Start
1. Turn off the power switch.
2. Remove the top panel. (Refer to Section 1-2-1.)
3. Set the switch S100-8 (J-3) on the CP-364 board to
ON.
S100
4. Re-attach the top panel. (Refer to Section 1-2-1.)
5. Turn on the power switch.
6. Check to see that all LEDs light for only one second.
The test mode starts.
n
If there is an LED that does not light, see Section 2-31, “Troubleshooting for the Power-on Sequence Error”
to clarify the cause.
7. Check to see that the 7SEG LEDs light as “99”,“88”, “77”, “66”, “55”, “44”, “33”, “22”, “11”
and “00” at intervals of 500 msec.
n
If the 7SEG LED does not light as described above,
the subsequent test cannot be carried out.
See Setion 2-3-1, “Troubleshooting for the Power-on
Sequence Error” or Setion 2-3-7, “Troubleshotting for
LED Test Error” to clarify the cause.
ON
2345678
1
: Switch position
2-2-4. Selecting and Executing of the Test Item
. To select the test item, select it using the [+]/[_] button
when the test item number is displayed on the 7SEG
LED.
. To execute the test item, press the “STORE” button
when the test item number is displayed.
. To display the test item number, press the “CANCEL”
button while executing all test items.
. All test items are executed repeatedly. To quit repeating
the tests, press the “CANCEL” button.
n
If the [+], [_], “STORE” and “CANCEL” buttons do not
operate as described above, see Section 2-3-2, “Trouble-
shooting for Test Selection Error” to clarify the cause.
Test No.Test itemTroubleshooting
01ROM version displaySection 2-3-3
02ROM testSection 2-3-4
03RAM testSection 2-3-5
04NV-RAM testSection 2-3-6
05LED testSection 2-3-7
067SEG LED testSection 2-3-8
07Switch testSection 2-3-9
08Rotary encoder testSection 2-3-10
09RS-422A testSection 2-3-11
8. Check to see that the 7SEG LEDs display “01”.
(The numeric character indicates the test item number.)
Quit
1. Turn off the power switch.
2. Set the switch S100-8 (J-3) on the CP-364 board back
to OFF.
HKDV-900
2-3 (E)
Page 16
2-2. Self Diagnostic Mode
2-2-5. Test Procedure
The detailed operation of each test and its judgment
method are described below.
Each test can be separately and independently executed
without following the specified order.
Usually, follow the order of the test item number to
execute a one-time test.
1. ROM version display
Set the test item number to “01” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
The ROM version is displayed alternating the integral part
and decimal point part for 500 msec. each on the 7SEG
LEDs.
When indicating the integral part, a numeric character is
displayed on the left 7SEG LED. An under-bar on the
right 7SEG LED indicates that it is the integral part
display.
When indicating the decimal point part, two numeric
characters are displayed.
n
If the version is not displayed properly, see Section 2-3-3,
“Troubleshooting for ROM Version Display Error” to
clarify the cause.
2. ROM test
Set the test item number to “02” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
Calculates the checksum in an area of a ROM, and then
compares it with the checksum written in the ROM.
If the comparison result coincides, “PA” is displayed on
the 7SEG LED. If it does not coincide, “Er” indicating an
error is displayed.
n
. If “Er” is displayed, see Section 2-3-4, “Troubleshoot-
ing for ROM Test Error” to clarify the cause.
. If the comparison of the checksums which is more than
two bytes does not coincide, an error cannot be detected
because the checksum is caliculated by simple addition.
PAEr
(OK)(Error)
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
1
1
(Integral part)(Decimal point part)
(Example) : Version 1.02
To quite the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
02
3. RAM test
Set the test item number to “03” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
Writes “ffh” in the every area of the RAM to check that the
written data can be read properly. Next, writes the data of
“aah”, “55h”, and then “00h” to check the reading.
If the test result is properly, “PA” is displayed on the
7SEG LED. If it is not properly, “Er” indicating an error
is displayed on the 7SEG LED.
n
If “Er” is displayed, see Section 2-3-5, “Troubleshooting
for RAM Test Error” to clarify the cause.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
2-4 (E)
HKDV-900
Page 17
2-2. Self Diagnostic Mode
4. NV-RAM test
n
Do not turn off the power switch during an NV-RAM test
to avoid the risk of the NV-RAM data failure.
Before turning off the power switch, press the “CANCEL”
button to return the display to the test item number.
Set the test item number to “04” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
Writes “ffh” in the every area of the RAM to check that the
written data can be read properly. Next, writes the data of
“aah”, “55h”, and then “00h” to check the reading.
If the test result is properly, “PA” is displayed on the
7SEG LED. If it is not properly, “Er” indicating an error
is displayed on the 7SEG LED.
n
If “Er” is displayed, see Section 2-3-6, “Troubleshooting
for NV-RAM Test Error” to clarify the casue.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
5. LED test
Set the test item number to “05” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
(1) All LEDs test result display
When an LED test is activated, all LEDs (including
with the LEDs in a pushbutton switch) first light for
one second and, after that, go off for one second.
This operation is repeated three times, and then
completed. Next, the single test of LED in the pushbutton switch is executed.
(3) LEVEL LED test result display
The uppermost LEVEL LED in the five-LED row at
the left of a rotary encoder in the “MASTER” part
firstly lights for 300 msec.. And then, each LED
sequentially blinks in the down direction.
Blinking the LEDs is sequentially shifted to the right
row of LEVEL LEDs. When blinking the LEVEL
LEDs in “_” part, all these LED tests are completed.
This test operation returns to all LEDs test of (1) and
repeats the tests unless you quit it.
Check to see that all the LEDs are properly operated.
n
If the result is not displayed properly, see Section 2-37, “Troubleshooting for LED Test Error” to clarify the
cause.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
6. 7SEG LED test
Set the test item number to “06” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
The 7SEG LEDs count down from “99” to “00” at
intervals of 500 msec. as when activating the test mode.
The countdown is carried out repeatedly.
Check to see that the 7SEG LEDs are properly operated.
n
If the countdown display is not properly, see Section 2-3-8,
“Troubleshooting for 7SEG LED Test Error” to clarify the
cause.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
(2) Single test result display of LED in pushbutton switch
The “HD” button on the leftmost lights for only 300
msec. And then, each button sequentially lights in the
right direction at intervals of 300 msec..
Blinking the “PRESET” botton on the rightmost
means that this single LED tests are completed. Next,
LEVEL LED test is executed.
HKDV-900
2-5 (E)
Page 18
2-2. Self Diagnostic Mode
7. Switch test
Set the test item number to “07” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
(1) LED built-in pushbutton switch test
Press the LED built-in pushbotton switches on the
front panel to check to see that the LED of each button
lights.
Press the switches again and check to see that the
LEDs goes off.
(2) Pushbutton switch test
Press the pushbotton switches on the front panel (not
including with “CANCEL”) which no LED is built in.
Check to see that the numeric character corresponding
to the pressed switch is displayed on the left 7SEG
LED. (Refer to the following table.)
The pushbotton switches and 7SEG LED display:
SwitchDisplay on left digit
+0
_1
STORE2
LOAD3
(3) Slide switch test
Remove the top panel, and then set the switches S1017 and S101-8 (J-3) on the CP-364 board to ON.
Check to see that a numeric character corresponding to
the switch settings is displayed on the right 7SEG
LED. (Refer to the table below.)
S101
ON
2345678
1
: Switch position
Slide switch settings and 7SEG LED display:
S101-7S101-8Display on right digit
ONON3
OFFON2
ONOFF1
OFFOFF0
n
If the above tests are not operated properly, see Section 2-39, “Troubleshooting for Switch Test Error” to clarify the
cause.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
2-6 (E)
8. Rotary encoder test
Set the test item number to “08” using the [+]/[_] button,
and then press the “STORE” button to activate a test.
Check the following operations of each rotary encoder.
(1) LEVEL LED indication test
1. Check to see that the LEVEL LED (U) at the
center of the left side of the rotary encoder lights.
2. Slightly rotate the rotary encoder clockwise to
check that the light is shifted to the upper LEVEL
LED.
3. Rotate the rotary encoder clockwise by 180d or
more to check that the uppermost (maximum)
LEVEL LED lights.
4. Rotate the rotary encoder counterclockwise by
180d or more to check that the lowermost (minimum) LEVEL LED lights.
(2) 7SEG LEDs indication test
Rotate each rotary encoder to check to see that the
following values of the rotary encoder are displayed in
hexadecimal on the 7SEG LEDs.
n
The display of the 7SEG LEDs is automatically
switched to the corresponded value of rotating the
rotary encoder by rotating either its knob.
. 7SEG LEDs indication when rotating clockwise:
01 (when rotation starts) → FF (when the knob is
rotated by 180d) →00 (when the knob is rotated by
180d or more) →FF (immediately before the knob
is rotated by 360d)
. 7SEG LEDs indication when rotating counterclock-
wise:
FF (when rotation starts) → 00 (when the knob is
rotated by 180d) →FF (when the knob is rotated by
180d or more) →00 (immediately before the knob
is rotated by 360d)
Check all rotary encoders for the above operation.
n
If the above tests are not operated properly, see Section
2-3-10. “Troubleshooting for Rotary Encoder Test Error”
to clarify the cause.
To quit the test, press the “CANCEL” button. The 7SEG
LEDs display returns to the test item number.
HKDV-900
Page 19
2-2. Self Diagnostic Mode
9. RS-422A test
Connect the connector tool(s) to the RS-422A connectors at the rear. (Refer to Section 2-2-1.)
Set the test item number to “09” using the [+]/[_] button, and then press the “STORE” button to activate
a test.
Outputs data from “0h” to “ffh” to the RS-422A connector and test that the same data can be received.
n
The states of the test result display that is displayed on the 7SEG LEDs and the LED inside the CONTROL SELECT button will change depending on the number of connector tools to be connected.
The states of both LEDs are as follows:
When using the four tools:
Test result7SEG LED displayLED inside the CONTROL SELECT button
OK“PA”All light off.
NG“Er”LED of an abnormal port :Blinks.
LED of a normal port :Lights off.
When using the three tools or less:
Test result7SEG LED displayLED inside the CONTROL SELECT button
OK“Er”LED of a port to which the tool is connected :Lights off.
LED of a port to which the tool is not connected :Blinks.
NG“Er”LED of a port to which the tool is connected :Blinks.
LED of a port to which the tool is not connected :Blinks.
n
If “Er” is displayed, see Section 2-3-11, “Troubleshooting for RS-422A Test Error” to clarify the cause.
To quit the test, and press the “CANCEL” button. The 7SEG LEDs display returns to the test item
number.
n
To quit the self diagnostic mode, set the switch S100-8 (J-3) on the CP-364 board back to OFF.
HKDV-900
2-7 (E)
Page 20
2-3. Troubleshooting
2-3.Troubleshooting
The trouble that may occur during a self diagnostic test and its possible cause are described below.
2-3-1. Troubleshooting for the Power-on Sequence Error
All LEDs on the front panel does not light and stay the state
(1) Power supply input check
OK
Is the cable between the power connector
(CN600) on the CP-364 board and the
switching regulator properly connected?
NG
Connect the cable properly and test
again
(2) Switching regulator output check
To “(2) Switching regulator output check”
Does +5 V DC present to the pins 1 and
2 of connector CN600 on the CP-364
board?
NG
Disconnect the cable from the connector
CN600, and test the harness again
OK
Short between +5 V and GND on the
CP-364 board
(3) Switching regulator input check
Does the specified AC voltage present
to the AC input terminal of the switching
regulator?
OK
Check the fuse on the switching
regulator
OK
To “(4) CP-364 board power check”
NG
To “ (3) Switching regulator input check”
NG
Power supply line defect. Pull the cord out
and current conduction test
NG
Fuse defect
OK
Switching regulator defect
2-8 (E)
HKDV-900
Page 21
(4) CP-364 board power check
Is +5 V DC present to test point TP602
(J-1) on the CP-364 board?
OK
Is +3.3 V DC present to TP600 (G-1) ?
OK
Is +2.5 V DC present to TP601 (G-1) ?
OK
To “(5) Reset signal check”
(5) Reset signal check
Is TP501 (J-2) on the CP-364 board high
level?
NG
Are not reset signal line and GND
shorted?
OK
NG
Harness defect or soldering defect of
connector CN600
NG
+3.3 V power supply block defect
NG
+2.5 V power supply block defect
NG
Reset switch defect, soldering defect of
reset signal line or pattern-bridge of it
2-3. Troubleshooting
Are pin 1 and pin 2 of IC501
(J-2)
on the
CP-364 board high level?
NG
Did 10 seconds pass at least after the
power is turned on?
OK
IC defect of IC200
(G-1)
or IC202
(H-1)
on the CP-364 board
HKDV-900
2-9 (E)
Page 22
2-3. Troubleshooting
Several LEDs light and stay the state
(1) Debugging switch check
Is switch S100-1 (J-3) on the CP-364
board set to ON?
OK
Is pin 5 of IC100 (H-3) on the CP-364
board low level?
OK
Is reset signal (pin 88 : high level) of
CPU (IC100 on the CP-364 board) proper?
OK
Is clock signal (pin 79 : 24 MHz
rectangular wave) of CPU proper?
NG
NG
Set switch S100-1 to ON and test it again
NG
Switch S100 defect or soldering defect
NG
Switch S500 (J-1) defect or soldering defect
OK
Does address signal (pins 37 and 38) of
CPU present to TP521 (G-1) and
TP520 (G-1)?
OK
Is interrupt signal (pins 93, 92, 91, and 90
of IC100 : all high level) proper?
OK
Check data bus and address bus
(Is not pattern shorted?)
Is crystal oscillator output (pin 3 of X100
(H-2) :
12.288 MHz rectangular wave)
NG
X100 defect or soldering defect
proper?
OK
IC106 (H-2) defect on the CP-364 board
or soldering defect
LEDs light and go off, but several LEDs do not light
Refer to item 5 “LED Test” of
Section 2-2-4, “Test Procedure”.
2-10 (E)
HKDV-900
Page 23
The display state of LEDs is no change after repeating light on and off
or the 7SEG LEDs counter display is not proper
NG
Are harnesses connected to CN400 (D-3)
Connect harnesses properly and recheck them
and CN401 (A-3) on the CP-364 board
and
CN1 (C-1 : B side) and
CN2 (A-1 : B side)
on the CP-365 board
properly connected?
OK
NG
Are output of IC300 (F-3), IC302 (F-3),
IC305 (F-3), IC308 (F-2), and IC310 (F-2)
on
the CP-364 board proper?
IC300, IC302, IC305, IC308, IC310 defect
on the CP-364 board or soldering defect
OK
LED defect on the CP-365 board
or soldering defect
2-3. Troubleshooting
Countdown display of the 7SEG LED is too quick or too slow
Is oscillating clock (12.288 MHz) of
crystal oscillator proper?
The normal (main) program becomes active
Is switch S100-1 (J-3) on the CP-364
NG
Set switch S100-1 to ON and test it again
board set to ON?
OK
Is pin 5 of CPU (IC100 (H-3) on the
NG
Switch S100 defect or soldering defect
CPU-364 board) low level?
OK
Is switch S101 (J-3) on the CP-364 board
is set to the factory settings (all OFF)?
NG
Set the S101 to the factory settings (all OFF)
and turn on the main power
OK
Switch S101 defect, IC defect of
IC105 (J-2) and IC100 (H-3) on the
CP-364 board, or soldering defect
HKDV-900
2-11 (E)
Page 24
2-3. Troubleshooting
2-3-2. Troubleshooting for Test Selection Error
[+][+]
Cannot change the test item number even if
Is the harness between CN401 (A-3) on the
NG
CP-364 and CN2 (A-1 : B side) on the CP-365
boards properly connected?
OK
+5 V
Is input signal of IC311 (G-3)
(pin 35 : +, pin 33 : _)
on the CP-364 board proper?
GND
OK
IC311 defect on the CP-364 board or
soldering defect
Cannot execute the test item even if the “STORE” button is pressed
[_][_]
[+]/
[_] button is pressed
[+][+]
[_][_]
Connect harness connector properly and
recheck them
Contact defect of [+]/[_] botton switch
S114 or S117 (B-1/CP-365)
Short-circuit of [+]/[_] botton switch
S114 or S117 (B-1/CP-365)
NG
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the CP-365
Connect harness connectors properly and
recheck them
boards properly connected?
OK
+5 V
Is input signal at pin 38 of IC311 (G-3) on
Contact defect of “STORE” button switch
S102 (B-1/CP-365)
the CP-364 board proper?
GND
Short-circuit of “STORE” button switch
S102 (B-1/CP-365)
OK
IC311 defect on the CP-364 board or
soldering defect
Cannot quit the test mode even if the “CANCEL” button is pressed
NG
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the CP-365
Connect harness connectors properly and
recheck them
boards properly connected?
OK
Is input signal at pin 36 of IC311 (G-3) on
+5 V
Contact defect of “CNACEL” button switch
S110 (B-1/CP-365)
the CP-364 board proper?
GND
Short-circuit of “CANCEL” button switch
S110 (B-1/CP-365)
OK
IC311 defect on the CP-364 board or
soldering defect
2-12 (E)
HKDV-900
Page 25
The counter display changes without button operation
NG
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the CP-365
Connect harness connectors properly and
recheck them
boards properly connected?
2-3. Troubleshooting
OK
Is input signal of IC311 (G-3) (pin 35 : +,
pin 33 : _) on the CP-364 board proper?
+5 V and GND are repeated
[+]/[_] switch S114 or S117 (B-1/CP-365)
defect or harness disconnection
OK
IC311 defect on the CP-364 board or
soldering defect
2-3-3. Troubleshooting for ROM Version Display Error
The display of version is not correct
Replace ROM and recheck it
NG
Address bus short or data bus short
2-3-4. Troubleshooting for ROM Test Error
Error display
Replace ROM and reckeck it
NG
Address bus shot or data bus short
2-3-5. Troubleshooting for RAM Test Error
Error display
Replace RAM and recheck it
NG
Address bus short or data bus short
HKDV-900
2-13 (E)
Page 26
2-3. Troubleshooting
2-3-6. Troubleshooting for NV-RAM Test Error
An error is displayed
NG
Is the connection between pin 119 of
IC200 (G-1), pin 6 of IC201 (G-1) and pin 6
of IC203 (F-1) on the CP-364 board proper?
OK
Is the connection between pin 120 of IC200,
pin 5 of IC201 and pin 5 of IC203 proper?
OK
Are R220 (G-1: B side), pin 5 of IC201,
pin 5 of IC203 on the CP-364 board set to
+5 V? (Measure when an error indication
appears.)
OK
IC defect of either IC200, IC201 or IC203
Connection defect between IC200, IC201
and IC203
NG
Connection defect between IC200, IC201
and IC203
NG
Parts defect of R220 or soldering defect
2-3-7. Troubleshooting for LED Test Error
Only one LED does not light or it is dark
NG
Are output signals (ON : +3 V to +4 V/
OFF : GND) of control ICs (IC300 (F-3),
IC302 (F-3), IC305 (F-3), IC308 (F-2), and
IC310 (F-2) on the CP-364 board) proper?
OK
Is cathode to LED properly connected to
GND?
OK
Is control signal (anode ON : +2 V/OFF :
GND) to LED proper?
OK
LED that does not light is defective
IC defect or soldering defect
NG
Resistor defect or soldering defect
2-14 (E)
HKDV-900
Page 27
LEDs do not light in units of blocks or they are dark
(1) Black-colored LEDs in the following figure do not light properly.
2-3. Troubleshooting
POWER
IMAGE ENHANCER
HD
D1 D2INPUT
CONTROL
SELECT
OUTPUT
7SEG LED
_
+
CANCEL
CROP
STORE
LOAD
Is the harness between CN400 (D-3) on the
CP-364 and CN1 (C-1 : B side) on the CP-365
boards properly connected?
OK
Is WR signal of control IC (IC305 (F-3) on
the CP-364 board) proper?
OK
Is output signal (ON : +3 V to +4 V/OFF :
GND) of control ICs (IQI to 2Q8 on the
CP-364 board) proper?
OK
Is power supply (anode : +2 V) to LED
proper?
MASTER YPBPRSETUP SYNC PHASE FINE_
UNITYUNITYUNITY UNITY UNITY PRESET PRESET PRESET
SQUEEZE
LETTER
BOX
NG
Connect harness connectors properly and
recheck them
NG
Connection defect between IC200 (G-1) and
IC305 on the CP-364 board
NG
IC305 defect on the CP-364 board
NG
Defect of resistor block (on CP-365 board)
(2) Black-colored LEDs in the following figure do not light properly.
POWER
IMAGE ENHANCER
HD
D1 D2INPUT
CONTROL
SELECT
OUTPUT
7SEG LED
_
+
CANCEL
CROP
STORE
LOAD
Is the harness between CN400 (D-3) on the
CP-364 and CN1 (C-1 : B side) on the
MASTER YPBPRSETUP SYNC PHASE FINE_
UNITYUNITYUNITY UNITY UNITY PRESET PRESET PRESET
SQUEEZE
LETTER
BOX
NG
Connect harness connectors properly and
recheck them
CP-365 boards properly connected?
OK
NG
Is WR signal of control IC (IC302 (F-3) on
the CP-364 board) proper?
Connection defect between IC200 (G-1) and
IC302 on the CP-364 board
OK
NG
Is output signal (ON : +3 V to +4 V/OFF :
IC302 defect on the CP-364 board
GND) of control ICs (1Q1 to 2Q8 of IC302
on the CP-364 board) proper?
OK
NG
Is power supply (anode : +2 V) to LED
Defect of resistor block (on CP-365 board)
proper?
HKDV-900
2-15 (E)
Page 28
2-3. Troubleshooting
(3) Black-colored LEDs in the following figure do not light properly.
POWER
IMAGE ENHANCER
HD
D1 D2INPUT
CONTROL
SELECT
OUTPUT
7SEG LED
_
+
CANCEL
CROP
STORE
LOAD
Is the harness between CN400 (D-3) on the
CP-364 and CN1 (C-1 : B side) on the
CP-365 boards properly connected?
OK
Is WR signal of control IC (IC300 (F-3) on
the CP-364 board) proper?
OK
Is output signal (ON : +3 V to +4 V/OFF :
GND) of control ICs (1Q1 to 2Q8 of IC300
on the CP-364 board) proper?
OK
Is power supply (anode : +2 V) to LED
proper?
MASTER YPBPRSETUP SYNC PHASE FINE_
UNITYUNITYUNITY UNITY UNITY PRESET PRESET PRESET
SQUEEZE
LETTER
BOX
NG
Connect harness connectors properly and
recheck them
NG
Connection defect between IC200 (G-1) and
IC300 on the CP-364 board
NG
IC300 defect on the CP-364 board
NG
Defect of resistor block (on CP-365 board)
(4) Black-colored LEDs in the following figure do not light properly.
IMAGE ENHANCER
POWER
HD
D1 D2INPUT
1234
CONTROL
SELECT
OUTPUT
7SEG LED
_
+
CANCEL
AD
F
E
C
B
GG
B
C
E
F
DA
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the
CROP
STORE
LOAD
MASTER YPBPRSETUP SYNC PHASE FINE_
UNITYUNITYUNITY UNITY UNITY PRESET PRESET PRESET
SQUEEZE
LETTER
BOX
NG
Connect harness connectors properly and
recheck them
CP-365 boards properly connected?
OK
NG
Is WR signal of control IC (IC310 (F-2) on
the CP-364 board) proper?
Connection defect between IC200 (G-1) and
IC310 on the CP-364 board
OK
NG
Is output signal (ON : +3 V to +4 V/OFF :
IC310 defect on the CP-364 board
GND) of control ICs (1Q1 to 2Q8 of IC310
on the CP-364 board) proper?
OK
Is power supply (anode : +2 V) to LED proper?
2-16 (E)
NG
Defect of resistor block (on CP-365 board)
HKDV-900
Page 29
(5) Black-colored LEDs in the following figure do not light properly.
AD
F
E
C
B
GG
B
C
DA
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the
E
F
NG
Connect harness connectors properly and
recheck them
CP-365 boards properly connected?
OK
NG
Is WR signal of control IC (IC308 (F-2) on
the CP-364 board) proper?
Connection defect between IC200 (G-1) and
IC308 on the CP-364 board
OK
NG
Is output signal (ON : +3 V to +4 V/OFF :
IC308 defect on the CP-364 board
GND) of control ICs (1Q1 to 2Q3 of IC308
on the CP-364 board) proper?
OK
Is power supply (anode : +2 V) to LED proper?
NG
Defect of resistor block (on CP-365 board)
2-3. Troubleshooting
HKDV-900
2-17 (E)
Page 30
2-3. Troubleshooting
2-3-8. Troubleshooting for 7SEG LED Test Error
The display does not appear properly
NG
Is the harness between CN401 (A-3) on the
CP-364 and CN2 (A-1 : B side) on the
CP-365 boards properly connected?
OK
Is WR signal of control ICs (IC308 (F-2) and
IC310 (F-2) on the CP-364 board) proper?
OK
Is output signal (ON : +3 V to +4 V/OFF :
GND) of control ICs (1Q1 to 2Q3 of IC308,
and 2Q7 and 2Q8 of IC310 on the CP-364
board) proper?
OK
Is power supply (anode : +2 V) to LED
proper?
Connect harness connector properly and
recheck them
NG
Connection defect between IC200 (G-1),
IC308 and IC310 on the CP-364 board
NG
IC308 (F-2) and IC310 (F-2) defect on the
CP-364 board
NG
Defect of resistor block (on CP-365 board)
2-3-9. Troubleshooting for Switch Test Error
The LED does not light even if the button is pressed
Is input signal (ON : low/OFF : high) at
I0 to I7 of IC309 (G-3) and I0 to I15 of
IC311 (G-3) on the CP-364 board proper?
OK
Is LED test OK?
NG
LED defect in switch or soldering defect
NG
IC309 or IC311 defect on the CP-364 board
or soldering defect
2-18 (E)
HKDV-900
Page 31
The LED sometimes does not light when the button is pressed
2-3. Troubleshooting
Is input signal (ON : low/OFF : high) at
I0 to I7 of IC309 (G-3) and I0 to I15 of
IC311 (G-3) the CP-364 board stable?
OK
Connection defect of the harness between
CN400 (D-3), CN401 (A-3) on the CP-364
and CN1 (C-1 : B side), CN2 (A-1 : B side)
on the CP-365 boards
NG
IC309 or IC311 defect on the CP-364 board
or soldering short
The LED lights or blinks before the button is pressed
Is input signal (ON : low/OFF : high) at
I0 to I7 of IC309 (G-3) and I0 to I15 of
IC311 (G-3) on the CP-364 board kept low?
OK
Connection defect of the harness between
CN400 (D-3), CN401 (A-3) on the CP-364
and CN1 (C-1 : B side), CN2 (A-1 : B side)
on the CP-365 boards
NG
IC309 or IC311 defect on the CP-364 board
or soldering short
The 7SEG LED display does not change even if switch settings of S101-7 and S101-8 are
changed
Are CHROMA signal at pin 9 of IC105 (J-2)
on the CP-364 board and VIDEO signal
(_3 : low/_∞ : high) at pin 8 of IC105
proper?
NG
(The result display is fixed at +5 V)
Switch defect or short in line
(The result display is fixed at ground)
Switch defect, pull-up resistor defect,
or short in line
(The result display is fixed between +5 V and 0 V)
Line disconnection between switch and
IC105 on the CP-364 board
(The result display is unstable)
IC105 defect
HKDV-900
2-19 (E)
Page 32
2-3. Troubleshooting
2-3-10. Troubleshooting for Rotary Encoder Test Error
The display of LEDs does not change even if rotary encoder is rotated
Are harness connections among
CN402 (G-3) through CN409 (J-3) on
the CP-364 board proper?
OK
Are encoder signals present to the input
side of IC303 (H-3), IC304 (H-3),
IC306 (G-3) and IC307 (G-3) on the
CP-364 board?
OK
Is inverted signal of encoder present to
the output side of IC303, IC304, IC306
and IC307 on the CP-364 board?
OK
Is inverted signal of encoder present to
the
input side of IC200 (G-1) on the
CP-364 board?
OK
IC defect of IC200 or soldering defect
NG
Connect harness connectors properly
and re-test
NG
Connection defect of CN402 to CN409,
IC303, IC304, IC306 and IC307, or
encoder defect
NG
Parts defect of IC303, IC304, IC306 and
IC307, or soldering defect
NG
Disconnection of the line, or soldering
short
2-20 (E)
HKDV-900
Page 33
Cannot detect one rotating direction clockwise or counterclockwise
2-3. Troubleshooting
Are harness connections among
CN402 (G-3) through CN409 (J-3) on
the CP-364 board proper?
OK
Are signals A and B (pin 1 : +5 V, pin 2 :
signal A, pin 3 : signal B, pin 4 : GND) of
encoder present to the input side of
IC303 (H-3), IC304 (H-3), IC306 (G-3)
and IC307 (G-3) on the CP-364 board?
OK
Is inverted signal of encoder present to
the output side of IC303, IC304, IC306
and IC307 on the CP-364 board?
OK
Are signals A and B (pin 1 : +5 V, pin 2 :
signal A, pin 3 : signal B, pin 4 : GND) of
encoder present to the input side of
IC200 (G-1) on the CP-364 board?
NG
Connect harness connectors properly
and re-test
NG
Rotary encoder defect
NG
Parts defect of IC303, IC304, IC306 and
IC307, or soldering defect
NG
Disconnection on the line, or soldering
short
OK
IC defect of IC200 or soldering defect
The LEVEL LED of MAX or MIN is not indicated even if rotary encoder is turned 180
degrees
Are harness connections among
CN402 (G-3) through CN409 (J-3) on
NG
Connect harness connectors properly
and re-test
the CP-364 board proper?
OK
NG
Are signals A and B (pin 1 : +5 V,
Rotary encoder defect
pin 2 : signal A, pin 3 : signal B, pin 4 :
GND) of encoder present to the input side
of IC303 (H-3), IC304 (H-3), IC306 (G-3)
and IC307 (G-3) on the CP-364 board?
HKDV-900
2-21 (E)
Page 34
2-3. Troubleshooting
2-3-11. Troubleshooting for RS-422A Test Error
Error display
Are connector tools for test connected?
OK
NG
Are pin 12 of IC102 (J-1 : B Side) on the
CP-364 board and pin 12 of
IC101 (J-1 : B side) low?
OK
Are output signals of pin 48, pin 49, pin
50 and pin 51 of IC200 on the CP-365
board proper?
OK
Are output signals of pin 2, pin 6, pin
10 and pin 14 of IC102 on the CP-364
board proper?
Connection defect to IC200 (G-1) on the
CP-364 board
NG
IC200 defect on the CP-364 board or
soldering defect
Are output signals of pin 3, pin 13, pin 5 and
pin 11 of IC101 on the CP-364 board proper?
IC101 defect on the CP-364 board or
soldering defect
OK
NG
Are input signals of pin 53, pin 54, pin 55 and
pin 56 of IC200 on the CP-364 board proper?
Short or bridge on the line between IC101
and IC200. IC101 defect or soldering defect
OK
NG
Is output signal of pin 34 of IC200 on
the CP-364 board proper?
Short or bridge on the line between CPU
and IC200. IC200 defect or soldering defect
It takes much time (three seconds or more) to display the pass
Is clock frequency (pin 79 of IC100 (H-3)
on the CP-364 board : 6.144 MHz) proper?
2-22 (E)
HKDV-900
Page 35
Section 3
Spare Parts
3-1.Notes on Repair Parts
1. Safety Related Components Warning
w
Components marked ! are critical to safe operation.
Therefore, specified parts should be used in the case of
replacement.
2. Standardization of Parts
Some repair parts supplied by Sony differ from those
used for the unit. These are because of parts commonality and improvement.
Parts list has the present standardized repair parts.
3. Stock of Parts
Parts marked with “o” at SP (Supply Code) column of
the spare parts list may not be stocked. Therefore, the
delivery date will be delayed.
4. Harness
Harnesses with no part number are not registered as
spare parts.
In need of repair, get components shown in the list and
repair using them.
3-1.
HKDV-900
3-1
Page 36
Exploded View
3-2.Exploded View
22
a
PSW3 x 6
PSW4 x 10
1
PSW3 x 6
9
11
PSW4 x 8
13
cc
eeee
d
c
d
e
14
15
PSW4 x 8
PSW
3 x 6
PSW3 x 6
24
PSW3 x 6
7
PSW3 x 6
12
17
10
23
PSW3 x 6
PSW3 x 10
18
2
PSW3 x 6
PSW3 x 6
19
PSW3 x 6
20
5
16
b
PSW3 x 6
a
1
PSW4 x 10
8
b
3-2
21
PSW3 x 6
4
6
PSW3 x 6
3
19
HKDV-900
Page 37
No.Part No. SP Description
1A-6252-180-A o ANGLE ASSY,RACK
2A-8325-944-C o MOUNTED CIRCUIT BOARD, CP-364
3A-8325-945-C o MOUNTED CIRCUIT BOARD, CP-365
4A-8326-577-C o PANEL ASSY, FRONT
5X-2068-004-0 s TERMINAL ASSY
6X-3167-051-1 s KNOB ASSY,VOLUME
7! 1-413-917-12 s SWITCHING REG. (TDK.FAW05-10R)
81-466-955-11 s ENCODER, ROTARY
9! 1-762-954-11 s SWITCH, POWER
10! 1-794-177-11 s INLET, AC (WITH FILTER)
11! 1-960-729-11 o HARNESS, SUB (AC-SW)
12! 1-960-730-11 o HARNESS, SUB (AC-GND1)
13! 1-960-731-11 o HARNESS, SUB (AC-GND2)
14! 1-960-732-11 o HARNESS, SUB (DC-CP)
151-960-733-11 o HARNESS, SUB (CP-CP)
162-068-008-00 s WASHER
172-990-241-02 s HOLDER (A), PLUG
183-628-659-03 s PLATE,UPPER
193-628-669-01 o CAP (ALP)(TRANSLUCENT)
203-628-669-11 o CAP (ALP)
213-681-054-01 o POWER SW GUARD
223-688-814-11 s CAP,SWITCH
233-701-822-00 s HOLDER, WIRE
24! 1-576-133-11 s FUSE, GLASS 3.15A/250V (20MM)
Exploded View
Screws/Washers
7-682-947-01 s SCREW +PSW 3X6
7-682-949-09 s SCREW +PSW 3X10
7-682-961-01 s SCREW +PSW 4X8
7-682-962-01 s SCREW +PSW 4X10
------------------------ Ref. No.
or Q’ty Part No. SP Description
(CP-364 BOARD suffix 13-)
Ref. No.
or Q’ty Part No. SP Description
pcs A-8325-944-C s MOUNTED CIRCUIT BOARD, CP-364
1pc 8-759-684-98 o IC SST39VF040-70-4C-NH
1pc 8-759-589-41 s IC EPC2LC20
8pcs 7-682-547-04 s SCREW +B3X6
C638 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C639 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C640 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C641 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C642 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C100 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C101 1-163-005-11 s CAPACITOR CHIP CERAMIC 470PF
C102 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C103 1-163-005-11 s CAPACITOR CHIP CERAMIC 470PF
C106 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C643 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C644 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C645 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C646 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C647 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C400 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C401 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C402 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C403 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C404 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C648 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C649 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C650 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C651 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C652 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C405 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C406 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C407 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C500 1-100-672-11 s CAPACITOR, CHIP CERAMIC 10MF
C501 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C653 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C654 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C662 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C663 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C664 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C502 1-126-400-11 s CAPACITOR ELECT 22MF/35V(CHIP)
C503 1-126-405-11 s CAPACITOR,ELECT 10MF/50V(CHIP
C600 1-107-778-11 s CAPACITOR,ELECT 470MF/16V CHIP
C601 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C602 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C665 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C666 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C667 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C668 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C669 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C603 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C604 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C605 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C606 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C607 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C670 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C671 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C672 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C682 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C683 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C608 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C609 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C610 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C611 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C612 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C684 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C685 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C686 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C687 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C688 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C613 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C614 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C615 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C616 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C617 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C689 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C690 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C691 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C692 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C693 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C618 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C619 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C620 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C621 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C622 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C694 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C695 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C696 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C697 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C698 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C623 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C624 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C625 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C626 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C627 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C699 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C700 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C701 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C702 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C703 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C628 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C629 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C630 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C631 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C632 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C704 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C705 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C706 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C707 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C708 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C633 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C634 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C635 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C636 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C637 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C709 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C710 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C711 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
C712 1-163-038-91 s CAPACITOR,CHIP CERAMIC 0.1MF
3-4
HKDV-900
Page 39
(CP-364 BOARD suffix 13-)
(CP-364 BOARD suffix 13-)
Ref. No.
or Q’ty Part No. SP Description
C713 1-126-394-11 s CAPACITOR,ELECT 10MF/16V(CHIP)
C714 1-107-778-11 s CAPACITOR,ELECT 470MF/16V CHIP
C715 1-126-394-11 s CAPACITOR,ELECT 10MF/16V(CHIP)
C716 1-107-778-11 s CAPACITOR,ELECT 470MF/16V CHIP
Ref. No.
or Q’ty Part No. SP Description
IC306 8-759-389-28 s IC 74LCX14MTCX
IC307 8-759-389-28 s IC 74LCX14MTCX
IC308 8-759-527-58 s IC SN74ABT16374ADGGR
IC309 8-759-389-45 s IC 74LCX16244MTDX
IC310 8-759-527-58 s IC SN74ABT16374ADGGR
CN100 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
CN101 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
CN102 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
CN103 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
CN200 1-506-469-11 s PIN,CONNECTOR (4P)
IC311 8-759-389-45 s IC 74LCX16244MTDX
IC501 8-759-196-96 s IC TC7SH08FU (TE85R)
IC502 8-759-594-71 s IC TC7SH14FU-TE85R
IC503 8-759-196-96 s IC TC7SH08FU (TE85R)
IC504 8-759-669-69 s IC TLC7733IPWR-12
CN201 1-506-473-11 o PIN,CONNECTOR 8P
CN400 1-565-689-11 o HEADER,FLAT CABLE 60P
CN401 1-565-689-11 o HEADER,FLAT CABLE 60P
CN402 1-506-469-11 s PIN,CONNECTOR (4P)
CN403 1-506-469-11 s PIN,CONNECTOR (4P)
IC505 8-759-989-91 s IC TL7705ACPS
IC506 8-759-456-26 s IC 74LCX541MTCX
IC507 8-759-456-26 s IC 74LCX541MTCX
IC600 8-749-018-23 s IC LT1764EQ-E2
IC601 8-749-018-23 s IC LT1764EQ-E2
CN404 1-506-469-11 s PIN,CONNECTOR (4P)
CN405 1-506-469-11 s PIN,CONNECTOR (4P)
CN406 1-506-469-11 s PIN,CONNECTOR (4P)
IS103 1-540-151-11 s SOCKET, IC
IS202 1-251-093-11 s SOCKET,IC
CN407 1-506-469-11 s PIN,CONNECTOR (4P)
CN408 1-506-469-11 s PIN,CONNECTOR (4P)
R100 1-216-295-91 s CONDUCTOR, CHIP (2012)
R101 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
CN409 1-506-469-11 s PIN,CONNECTOR (4P)
CN600 1-564-918-11 o PIN,CONNECTOR 4P
R102 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R103 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R104 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
D100 8-719-016-74 s DIODE 1SS352
D101 8-719-016-74 s DIODE 1SS352
D102 8-719-016-74 s DIODE 1SS352
D103 8-719-016-74 s DIODE 1SS352
D104 8-719-016-74 s DIODE 1SS352
R105 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R106 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R200 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R201 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R202 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
D105 8-719-016-74 s DIODE 1SS352
D106 8-719-016-74 s DIODE 1SS352
D107 8-719-016-74 s DIODE 1SS352
D500 8-719-016-74 s DIODE 1SS352
D501 8-719-016-74 s DIODE 1SS352
R203 1-216-295-91 s CONDUCTOR, CHIP (2012)
R204 1-216-009-91 s C-RES,S 22-1/10W J
R205 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R206 1-216-295-91 s CONDUCTOR, CHIP (2012)
R207 1-216-295-91 s CONDUCTOR, CHIP (2012)
E600 1-535-877-22 s CHIP,CHECKER (TEST POINT)
E601 1-535-877-22 s CHIP,CHECKER (TEST POINT)
E602 1-535-877-22 s CHIP,CHECKER (TEST POINT)
E603 1-535-877-22 s CHIP,CHECKER (TEST POINT)
E604 1-535-877-22 s CHIP,CHECKER (TEST POINT)
R208 1-216-295-91 s CONDUCTOR, CHIP (2012)
R209 1-216-295-91 s CONDUCTOR, CHIP (2012)
R210 1-216-295-91 s CONDUCTOR, CHIP (2012)
R211 1-216-295-91 s CONDUCTOR, CHIP (2012)
R212 1-216-295-91 s CONDUCTOR, CHIP (2012)
E605 1-535-877-22 s CHIP,CHECKER (TEST POINT)
R213 1-216-295-91 s CONDUCTOR, CHIP (2012)
FB100 1-412-363-11 s FERRITE, EMI (SMD)
FB101 1-412-363-11 s FERRITE, EMI (SMD)
FB102 1-412-363-11 s FERRITE, EMI (SMD)
R214 1-216-295-91 s CONDUCTOR, CHIP (2012)
R215 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R216 1-216-295-91 s CONDUCTOR, CHIP (2012)
R217 1-216-295-91 s CONDUCTOR, CHIP (2012)
IC100 8-759-564-97 s IC HD6417708SF60
IC101 8-759-923-64 s IC AM26LS32ACNS
IC102 8-759-923-65 s IC AM26LS31CNS
IC103 6-800-756-02 s IC SST39VF040-HKDV900-V121
IC104 6-701-874-01 s IC IDT71V016SA15PH8(SCD2994)
R218 1-216-295-91 s CONDUCTOR, CHIP (2012)
R219 1-216-295-91 s CONDUCTOR, CHIP (2012)
R220 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R221 1-216-013-00 s RESISTOR,CHIP 33 1/10W(2012)
R222 1-216-295-91 s CONDUCTOR, CHIP (2012)
IC105 8-759-456-26 s IC 74LCX541MTCX
IC106 8-759-466-55 s IC 74LCX74MTCX
IC200 8-759-691-42 s IC EPF10K50EQC240-2N
IC201 8-759-693-82 s IC HN58X2464FPIZ
IC202 8-759-834-41 o IC EPC2LC20-HKDV900-V100
R223 1-216-295-91 s CONDUCTOR, CHIP (2012)
R224 1-216-295-91 s CONDUCTOR, CHIP (2012)
R225 1-216-295-91 s CONDUCTOR, CHIP (2012)
R226 1-216-295-91 s CONDUCTOR, CHIP (2012)
R227 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
IC203 8-759-693-82 s IC HN58X2464FPIZ
IC300 8-759-527-58 s IC SN74ABT16374ADGGR
IC301 8-759-389-45 s IC 74LCX16244MTDX
IC302 8-759-527-58 s IC SN74ABT16374ADGGR
IC303 8-759-389-28 s IC 74LCX14MTCX
R228 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R229 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R230 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R231 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R233 1-216-295-91 s CONDUCTOR, CHIP (2012)
IC304 8-759-389-28 s IC 74LCX14MTCX
IC305 8-759-527-58 s IC SN74ABT16374ADGGR
R300 1-216-295-91 s CONDUCTOR, CHIP (2012)
HKDV-900
3-5
Page 40
(CP-364 BOARD suffix 13-)
(CP-364 BOARD suffix 13-)
Ref. No.
or Q’ty Part No. SP Description
R301 1-216-295-91 s CONDUCTOR, CHIP (2012)
R302 1-216-295-91 s CONDUCTOR, CHIP (2012)
R303 1-216-295-91 s CONDUCTOR, CHIP (2012)
R304 1-216-295-91 s CONDUCTOR, CHIP (2012)
R305 1-216-295-91 s CONDUCTOR, CHIP (2012)
R306 1-216-295-91 s CONDUCTOR, CHIP (2012)
R307 1-216-295-91 s CONDUCTOR, CHIP (2012)
R308 1-216-295-91 s CONDUCTOR, CHIP (2012)
R309 1-216-295-91 s CONDUCTOR, CHIP (2012)
R310 1-216-295-91 s CONDUCTOR, CHIP (2012)
R311 1-216-295-91 s CONDUCTOR, CHIP (2012)
R312 1-216-295-91 s CONDUCTOR, CHIP (2012)
R313 1-216-295-91 s CONDUCTOR, CHIP (2012)
R314 1-216-295-91 s CONDUCTOR, CHIP (2012)
R315 1-216-295-91 s CONDUCTOR, CHIP (2012)
R316 1-216-295-91 s CONDUCTOR, CHIP (2012)
R317 1-216-295-91 s CONDUCTOR, CHIP (2012)
R318 1-218-367-11 s RESISTOR,METAL FILM CHIP 10K
R319 1-218-367-11 s RESISTOR,METAL FILM CHIP 10K
R500 1-216-093-91 s C-RES,S 68K-1/10W J
R501 1-216-295-91 s CONDUCTOR, CHIP (2012)
R502 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R503 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R504 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R505 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
Ref. No.
or Q’ty Part No. SP Description
R540 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012)
R541 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012)
R542 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R543 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R544 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R545 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R546 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R547 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R548 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R549 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R550 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R551 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R552 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R553 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R554 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R555 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R556 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R557 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R558 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R559 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R560 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R561 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R562 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R563 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R564 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R506 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R507 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R508 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R509 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R510 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R511 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R512 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R513 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R514 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R515 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R516 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R517 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R518 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R519 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R520 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R521 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R522 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R523 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R524 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R525 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R526 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R527 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R528 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R529 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R530 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R531 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R532 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R533 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R534 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R535 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R565 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R566 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R567 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R568 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R569 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R570 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R571 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R572 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R573 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R574 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R575 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R576 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R577 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R578 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R579 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R580 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R581 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R582 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R583 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R584 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R585 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R586 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R587 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R588 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R589 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R590 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R591 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R592 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R593 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R600 1-216-611-11 s RESISTOR,CHIP 22 1/10W (2012)
R536 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R537 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R538 1-216-295-91 s CONDUCTOR, CHIP (2012)
R539 1-216-295-91 s CONDUCTOR, CHIP (2012)
R601 1-216-664-11 s RESISTOR,CHIP 3.6K 1/10W(2125)
R602 1-216-663-11 s RESISTOR,CHIP 3.3K 1/10W(2012)
R603 1-216-675-11 s RESISTOR,CHIP 10K 1/10W(2012)
R604 1-216-669-11 s RESISTOR,CHIP 5.6K 1/10W(2012)
3-6
HKDV-900
Page 41
----------------------------
(CP-364 BOARD suffix 13-)
CP-364 BOARD (suffix 11, 12)
--------------------------- Ref. No.
or Q’ty Part No. SP Description
R605 1-216-663-11 s RESISTOR,CHIP 3.3K 1/10W(2012)
Ref. No.
RB101 1-236-908-11 s RESISTOR,NETWORK 10K (3216)
or Q’ty Part No. SP Description
RB102 1-236-908-11 s RESISTOR,NETWORK 10K (3216)
RB103 1-239-306-11 s RESISTOR ARRAY,CHIP 10K
1pc*2 A-8325-944-C o MOUNTED CIRCUIT BOARD, CP-364
1pc*1 A-8325-944-C o MOUNTED CIRCUIT BOARD, CP-364
S100 1-692-271-31 s SWITCH, SLIDE
S101 1-692-271-31 s SWITCH, SLIDE
1pc! 1-413-917-12 s SWITCHING REG.(TDK.FAW05-10R)
1pc! 1-532-827-11 s FUSE 3.15A/125V (20MM)
S500 1-571-381-21 s SWITCH,TACTIL (REFLOW TYPE)
C1001-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
TP100 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP500 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP501 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP502 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C1011-163-005-11 s CAPACITOR CHIP CERAMIC 470PF
C1021-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C1031-163-005-11 s CAPACITOR CHIP CERAMIC 470PF
C1061-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
TP503 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C4001-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
TP504 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP505 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP506 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP507 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C4011-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C4021-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C4031-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C4041-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
TP508 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C4051-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
TP509 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP510 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP511 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP512 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C4061-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C4071-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF
C5001-104-913-11 s CAPACITOR,TANTALUM 10MF/16V
C5011-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
TP513 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C5021-126-400-11 s CAPACITOR ELECT 22MF/35V(CHIP)
TP514 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP515 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP516 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP517 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP518 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C503 *2 1-126-405-11 s CAPACITOR, ELECT 10MF/50V(CHIP)
*1 1-126-964-11 s CAPACITOR, ELECT 10MF/50V
C6001-126-941-11 s CAPACITOR,ELECT 470MF/25V
C6011-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C6021-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
TP519 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP520 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP521 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP600 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP601 1-535-877-22 s CHIP,CHECKER (TEST POINT)
TP602 1-535-877-22 s CHIP,CHECKER (TEST POINT)
C6031-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C6041-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C6051-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6061-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6071-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6081-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6091-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
X100 1-781-655-11 s OSCILLATOR, CRYSTAL
C6101-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6111-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6121-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6131-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6141-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6151-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6161-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6171-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6181-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6191-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6201-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6211-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6221-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6231-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6241-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6251-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6261-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6271-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6281-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6291-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6301-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6311-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6321-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
HKDV-900
C6331-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
3-7
Page 42
(CP-364 BOARD suffix 11, 12)
(CP-364 BOARD suffix 11, 12)
Ref. No.
or Q’ty Part No. SP Description
C6341-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6351-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6361-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C6371-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C638 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C639 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C640 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C641 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C642 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C643 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C644 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C645 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C646 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C647 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C648 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C649 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C650 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C651 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C652 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C653 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C654 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C662 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C663 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C664 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
Ref. No.
or Q’ty Part No. SP Description
C709 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C710 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C711 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C712 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C718 1-163-009-11 s CAPACITOR,CERAMIC 1000PF/50V
C722 1-163-263-11 s CAPACITOR CERAMIC 330PF/50V
C723 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C724 1-115-340-11 s CAPACITOR CERAMIC 0.22MF/25V B
C725 1-107-686-11 s CAPACITOR,TANTALUM 4.7MF/16V
C726 1-127-530-11 s CAPACITOR,ELECT 22MF/20V
C727 1-127-518-11 s CAPACITOR,ELECT 100MF/16V
C728 1-127-530-11 s CAPACITOR,ELECT 22MF/20V
C729 1-127-518-11 s CAPACITOR,ELECT 100MF/16V
C730 1-127-518-11 s CAPACITOR,ELECT 100MF/16V
C731 1-164-161-11 s CAPACITOR, CERAMIC 2200PF/100V
C735 1-163-259-91 s CAPACITOR,CHIP CERAMIC 220PF
C736 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C737 1-115-340-11 s CAPACITOR CERAMIC 0.22MF/25V B
C738 1-107-686-11 s CAPACITOR,TANTALUM 4.7MF/16V
C739 1-127-512-00 s CAPACITOR,ELECT 10MF/25V
C740 1-127-512-00 s CAPACITOR,ELECT 10MF/25V
C741 1-127-517-11 s CAPACITOR,ELECT 150MF/16V
C742 1-127-512-00 s CAPACITOR,ELECT 10MF/25V
C743 1-127-517-11 s CAPACITOR,ELECT 150MF/16V
C665 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
CN100 *2 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
C666 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C667 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C668 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C669 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C670 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
*1 1-563-771-11 s SOCKET,D-SUB CONNECTOR 15P
CN101 *2 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
*1 1-563-771-11 s SOCKET,D-SUB CONNECTOR 15P
CN102 *2 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
*1 1-563-771-11 s SOCKET,D-SUB CONNECTOR 15P
C671 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C672 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C682 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C683 1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP)
C684 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
CN103 *2 1-563-770-11 s SOCKET,D-SUB CONNECTOR 9P
*1 1-563-771-11 s SOCKET,D-SUB CONNECTOR 15P
CN200 1-506-469-11 s PIN,CONNECTOR (4P)
CN201 1-506-473-11 o PIN,CONNECTOR 8P
CN400 1-565-689-11 o HEADER,FLAT CABLE 60P
CN401 1-565-689-11 o HEADER,FLAT CABLE 60P
C685 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C686 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C687 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C688 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C689 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
CN402 1-506-469-11 s PIN,CONNECTOR (4P)
CN403 1-506-469-11 s PIN,CONNECTOR (4P)
CN404 1-506-469-11 s PIN,CONNECTOR (4P)
CN405 1-506-469-11 s PIN,CONNECTOR (4P)
CN406 1-506-469-11 s PIN,CONNECTOR (4P)
C690 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C691 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C692 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C693 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C694 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C695 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C696 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C697 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C698 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C699 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C700 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C701 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C702 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C703 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C704 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C705 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C706 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C707 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
C708 1-163-038-00 s CAPACITOR, CERAMIC 0.1MF/25V
CN407 1-506-469-11 s PIN,CONNECTOR (4P)
CN408 1-506-469-11 s PIN,CONNECTOR (4P)
CN409 1-506-469-11 s PIN,CONNECTOR (4P)
CN600 1-564-918-11 o PIN,CONNECTOR 4P
D100 8-719-016-74 s DIODE 1SS352
D101 8-719-016-74 s DIODE 1SS352
D102 8-719-016-74 s DIODE 1SS352
D103 8-719-016-74 s DIODE 1SS352
D104 8-719-016-74 s DIODE 1SS352
D105 8-719-016-74 s DIODE 1SS352
D106 8-719-016-74 s DIODE 1SS352
D107 8-719-016-74 s DIODE 1SS352
D500 8-719-016-74 s DIODE 1SS352
D501 8-719-016-74 s DIODE 1SS352
D600 8-719-058-24 s DIODE RB501V-40TE17
D601 8-719-058-24 s DIODE RB501V-40TE17
D602 8-719-048-40 s DIODE MBRS140T3
D603 8-719-048-40 s DIODE MBRS140T3
3-8
HKDV-900
Page 43
(CP-364 BOARD suffix 11, 12)
(CP-364 BOARD suffix 11, 12)
Ref. No.
or Q’ty Part No. SP Description
FB100 1-412-363-11 s FERRITE, EMI (SMD)
FB101 1-412-363-11 s FERRITE, EMI (SMD)
FB102 1-412-363-11 s FERRITE, EMI (SMD)
Ref. No.
or Q’ty Part No. SP Description
R209 1-216-295-00 s CONDUCTOR, CHIP (2012)
R210 1-216-295-00 s CONDUCTOR, CHIP (2012)
R211 1-216-295-00 s CONDUCTOR, CHIP (2012)
R212 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC100 8-759-586-27 s IC HD6417708STF60
R213 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC101 8-759-923-64 s IC AM26LS32ACNS
IC102 8-759-923-65 s IC AM26LS31CNS
IC103 6-800-756-01 o IC SST39VF040-HKDV900-V110
IC104 8-759-645-48 s IC IDT71V016S15PH-TL
R214 1-216-295-00 s CONDUCTOR, CHIP (2012)
R215 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R216 1-216-295-00 s CONDUCTOR, CHIP (2012)
R217 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC105 8-759-456-26 s IC 74LCX541MTCX
R218 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC106 8-759-466-55 s IC 74LCX74MTCX
IC200 8-759-691-42 s IC EPFQC240AB
IC201 8-759-693-82 s IC HN58X2464FPIZ
IC202 8-759-834-41 o IC EPC2LC20-HKDV900-V100
R219 1-216-295-00 s CONDUCTOR, CHIP (2012)
R220 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R221 1-216-013-00 s RESISTOR,CHIP 33 1/10W(2012)
R222 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC203 8-759-693-82 s IC HN58X2464FPIZ
R223 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC300 8-759-527-58 s IC SN74ABT16374ADGGR
IC301 8-759-389-45 s IC 74LCX16244MTDX
IC302 8-759-527-58 s IC SN74ABT16374ADGGR
IC303 8-759-389-28 s IC 74LCX14MTCX
R224 1-216-295-00 s CONDUCTOR, CHIP (2012)
R225 1-216-295-00 s CONDUCTOR, CHIP (2012)
R226 1-216-295-00 s CONDUCTOR, CHIP (2012)
R227 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
IC304 8-759-389-28 s IC 74LCX14MTCX
R228 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
IC305 8-759-527-58 s IC SN74ABT16374ADGGR
IC306 8-759-389-28 s IC 74LCX14MTCX
IC307 8-759-389-28 s IC 74LCX14MTCX
IC308 8-759-527-58 s IC SN74ABT16374ADGGR
R229 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R230 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R231 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R233 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC309 8-759-389-45 s IC 74LCX16244MTDX
R300 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC310 8-759-527-58 s IC SN74ABT16374ADGGR
IC311 8-759-389-45 s IC 74LCX16244MTDX
IC501 8-759-196-96 s IC TC7SH08FU (TE85R)
IC502 8-759-594-71 s IC TC7SH14FU-TE85R
R301 1-216-295-00 s CONDUCTOR, CHIP (2012)
R302 1-216-295-00 s CONDUCTOR, CHIP (2012)
R303 1-216-295-00 s CONDUCTOR, CHIP (2012)
R304 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC503 8-759-196-96 s IC TC7SH08FU (TE85R)
R305 1-216-295-00 s CONDUCTOR, CHIP (2012)
IC504 *2 8-759-669-69 s IC TLC7733IPWR-12
*1 8-759-569-91 s IC TLC7733IPWR
IC505 8-759-989-91 s IC TL7705ACPS
IC506 8-759-456-26 s IC 74LCX541MTCX
IC507 8-759-456-26 s IC 74LCX541MTCX
R306 1-216-295-00 s CONDUCTOR, CHIP (2012)
R307 1-216-295-00 s CONDUCTOR, CHIP (2012)
R308 1-216-295-00 s CONDUCTOR, CHIP (2012)
R309 1-216-295-00 s CONDUCTOR, CHIP (2012)
R310 1-216-295-00 s CONDUCTOR, CHIP (2012)
IS103 *2 1-540-151-21 s SOCKET,IC
IS202 1-251-093-11 o SOCKET,IC
R311 1-216-295-00 s CONDUCTOR, CHIP (2012)
R312 1-216-295-00 s CONDUCTOR, CHIP (2012)
L600 1-469-060-11 s INDUCTOR
L601 1-469-060-11 s INDUCTOR
R313 1-216-295-00 s CONDUCTOR, CHIP (2012)
R314 1-216-295-00 s CONDUCTOR, CHIP (2012)
R315 1-216-295-00 s CONDUCTOR, CHIP (2012)
Q600 8-729-041-86 s TRANSISTOR SI4412DY-T1
Q601 8-729-041-86 s TRANSISTOR SI4412DY-T1
Q602 8-729-045-16 s TRANSISTOR SI4410DY-T1-REVA
Q603 8-729-045-16 s TRANSISTOR SI4410DY-T1-REVA
R316 1-216-295-00 s CONDUCTOR, CHIP (2012)
R317 1-216-295-00 s CONDUCTOR, CHIP (2012)
R500 1-216-093-00 s RESISTOR, CHIP 68K 1/10W(2012)
R501 1-216-295-00 s CONDUCTOR, CHIP (2012)
R100 1-216-295-00 s CONDUCTOR, CHIP (2012)
R502 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R101 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R102 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R103 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R104 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R503 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R504 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R505 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R506 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R105 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R507 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R106 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R200 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R201 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R202 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R508 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R509 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R510 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R511 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R203 1-216-295-00 s CONDUCTOR, CHIP (2012)
R512 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R204 1-216-009-00 s RESISTOR,CHIP 22 1/10W (2012)
R205 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R206 1-216-295-00 s CONDUCTOR, CHIP (2012)
R207 1-216-295-00 s CONDUCTOR, CHIP (2012)
R513 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R514 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R515 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R516 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R208 1-216-295-00 s CONDUCTOR, CHIP (2012)
HKDV-900
3-9
Page 44
(CP-364 BOARD suffix 11, 12)
(CP-364 BOARD suffix 11, 12)
Ref. No.
or Q’ty Part No. SP Description
R517 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R518 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R519 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R520 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R521 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R522 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R523 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R524 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R525 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R526 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R527 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R528 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R529 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R530 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R531 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R532 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R533 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R534 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R535 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R536 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R537 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R538 1-216-295-00 s CONDUCTOR, CHIP (2012)
R539 1-216-295-00 s CONDUCTOR, CHIP (2012)
R540 1-216-089-00 s RESISTOR CHIP 47K 1/10W(2012)
Ref. No.
or Q’ty Part No. SP Description
R576 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R577 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R578 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R579 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R580 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R581 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R582 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R583 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R584 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R585 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R586 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R587 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R588 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R589 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R590 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R591 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R592 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R593 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R600 1-216-675-11 s RESISTOR,CHIP 10K 1/10W(2012)
R601 1-216-675-11 s RESISTOR,CHIP 10K 1/10W(2012)
R602 1-218-232-91 s RESISTOR CHIP 4.7 1/2W (4532)
R603 1-218-232-91 s RESISTOR CHIP 4.7 1/2W (4532)
R604 1-208-807-11 s RESISTOR,CHIP 11K 1/10W (2125)
R605 1-208-806-11 s RESISTOR,CHIP 10K 1/10W (2012)
R541 1-216-089-00 s RESISTOR CHIP 47K 1/10W(2012)
RB101 1-236-908-11 s RESISTOR,NETWORK 10K (3216)
R542 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R543 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
RB102 1-236-908-11 s RESISTOR,NETWORK 10K (3216)
RB103 1-239-306-11 s RESISTOR ARRAY,CHIP 10K
R544 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R545 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R546 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
S100 1-692-271-31 s SWITCH, SLIDE
S101 1-692-271-31 s SWITCH, SLIDE
S500 1-571-381-21 s SWITCH,TACTIL (REFLOW TYPE)
R547 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R548 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
X100 1-781-655-11 s OSCILLATOR, CRYSTAL
R549 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R550 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R551 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R552 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R553 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R554 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R555 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R556 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R557 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R558 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R559 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R560 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R561 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R562 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R563 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R564 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R565 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R566 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R567 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R568 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R569 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R570 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R571 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R572 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R573 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R574 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R575 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
------------------------ Ref. No.
or Q’ty Part No. SP Description
(CP-365 BOARD suffix 13-)
Ref. No.
or Q’ty Part No. SP Description
pcs A-8325-945-C s MOUNTED CIRCUIT BOARD, CP-365
D250 8-719-938-67 s LED GL3EG8
D251 8-719-938-67 s LED GL3EG8
C301 1-100-620-91 s CAPACITOR, CHIP 47MF(3225)
C302 1-100-620-91 s CAPACITOR, CHIP 47MF(3225)
C303 1-100-620-91 s CAPACITOR, CHIP 47MF(3225)
D252 8-719-938-67 s LED GL3EG8
D253 8-719-938-67 s LED GL3EG8
D254 8-719-938-67 s LED GL3EG8
C304 1-100-620-91 s CAPACITOR, CHIP 47MF(3225)
D255 8-719-938-68 s LED GL3HY8
CN1 1-691-735-11 s HEADER, CONNECTOR PIN 60P
CN2 1-691-735-11 s HEADER, CONNECTOR PIN 60P
D256 8-719-938-67 s LED GL3EG8
D257 8-719-938-67 s LED GL3EG8
D258 8-719-938-67 s LED GL3EG8
D101 8-719-016-74 s DIODE 1SS352
D259 8-719-938-68 s LED GL3HY8
D102 8-719-016-74 s DIODE 1SS352
D103 8-719-016-74 s DIODE 1SS352
D104 8-719-016-74 s DIODE 1SS352
D105 8-719-016-74 s DIODE 1SS352
D260 8-719-938-68 s LED GL3HY8
D261 8-719-938-67 s LED GL3EG8
D262 8-719-938-67 s LED GL3EG8
D263 8-719-938-67 s LED GL3EG8
D106 8-719-016-74 s DIODE 1SS352
D264 8-719-938-68 s LED GL3HY8
D107 8-719-016-74 s DIODE 1SS352
D108 8-719-016-74 s DIODE 1SS352
D269 8-719-938-68 s LED GL3HY8
D109 8-719-016-74 s DIODE 1SS352
D110 8-719-016-74 s DIODE 1SS352
ND101 8-719-913-53 s LED ARRAY LA-301VL
ND102 8-719-913-53 s LED ARRAY LA-301VL
D111 8-719-016-74 s DIODE 1SS352
D112 8-719-016-74 s DIODE 1SS352
D113 8-719-016-74 s DIODE 1SS352
D114 8-719-016-74 s DIODE 1SS352
D115 8-719-016-74 s DIODE 1SS352
R101 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R102 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R103 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R104 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R105 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
D116 8-719-016-74 s DIODE 1SS352
D117 8-719-016-74 s DIODE 1SS352
D118 8-719-016-74 s DIODE 1SS352
D201 8-719-016-74 s DIODE 1SS352
D204 8-719-016-74 s DIODE 1SS352
R106 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R107 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R108 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R109 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R110 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
D207 8-719-016-74 s DIODE 1SS352
D210 8-719-016-74 s DIODE 1SS352
D213 8-719-016-74 s DIODE 1SS352
D216 8-719-016-74 s DIODE 1SS352
D219 8-719-016-74 s DIODE 1SS352
R111 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R112 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R113 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R114 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R115 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
D222 8-719-016-74 s DIODE 1SS352
D225 8-719-938-68 s LED GL3HY8
D226 8-719-938-67 s LED GL3EG8
D227 8-719-938-67 s LED GL3EG8
D228 8-719-938-67 s LED GL3EG8
R116 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R117 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R118 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R119 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R120 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
D230 8-719-938-68 s LED GL3HY8
D231 8-719-938-67 s LED GL3EG8
D232 8-719-938-67 s LED GL3EG8
D233 8-719-938-67 s LED GL3EG8
D234 8-719-938-68 s LED GL3HY8
R121 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R122 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R123 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R124 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R125 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
D235 8-719-938-68 s LED GL3HY8
D236 8-719-938-67 s LED GL3EG8
D237 8-719-938-67 s LED GL3EG8
D238 8-719-938-67 s LED GL3EG8
D239 8-719-938-68 s LED GL3HY8
R126 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R127 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R128 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R129 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R130 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
D240 8-719-938-68 s LED GL3HY8
D241 8-719-938-67 s LED GL3EG8
D242 8-719-938-67 s LED GL3EG8
D243 8-719-938-67 s LED GL3EG8
D244 8-719-938-68 s LED GL3HY8
R131 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R132 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R133 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R134 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R135 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
D245 8-719-938-68 s LED GL3HY8
D246 8-719-938-67 s LED GL3EG8
D247 8-719-938-67 s LED GL3EG8
D248 8-719-938-67 s LED GL3EG8
D249 8-719-938-68 s LED GL3HY8
R136 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R137 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R138 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R139 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R140 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
HKDV-900
3-11
Page 46
(CP-365 BOARD suffix 13-)
(CP-365 BOARD suffix 13-)
Ref. No.
or Q’ty Part No. SP Description
R141 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R142 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R143 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
Ref. No.
or Q’ty Part No. SP Description
R255 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R256 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R301 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R144 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R145 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
S101 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S102 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R201 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R202 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R203 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S103 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S104 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S105 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R204 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R205 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
S106 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S107 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R206 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R207 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R208 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S108 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S109 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S110 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R209 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R210 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S111 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S112 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R211 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R212 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R213 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
S113 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S114 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S115 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R214 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R215 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S116 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S117 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R216 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R217 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R218 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
S118 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S201 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S202 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R219 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R220 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S203 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S204 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R221 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R222 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R223 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
S205 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S206 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S207 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R224 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R225 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
S208 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R226 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R227 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R228 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R229 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R230 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R231 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R232 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R233 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R234 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R235 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R236 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R237 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R238 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R239 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R240 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R241 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R242 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R243 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R244 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R245 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R246 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R247 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R248 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R249 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R250 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R251 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R252 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R253 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R254 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
--------------------------- Ref. No.
or Q’ty Part No. SP Description
(CP-365 BOARD suffix 11, 12)
Ref. No.
or Q’ty Part No. SP Description
1pc A-8325-945-C o MOUNTED CIRCUIT BOARD, CP-365
D250 8-719-938-67 s LED GL3EG8
D251 8-719-938-67 s LED GL3EG8
C301 1-115-581-11 s CAPACITOR CHIP ELECT 100MF/16V
C302 1-115-581-11 s CAPACITOR CHIP ELECT 100MF/16V
C303 1-115-581-11 s CAPACITOR CHIP ELECT 100MF/16V
D252 8-719-938-67 s LED GL3EG8
D253 8-719-938-67 s LED GL3EG8
D254 8-719-938-67 s LED GL3EG8
C304 1-115-581-11 s CAPACITOR CHIP ELECT 100MF/16V
D255 8-719-938-68 s LED GL3HY8
CN1 1-691-735-11 s HEADER, CONNECTOR PIN 60P
CN2 1-691-735-11 s HEADER, CONNECTOR PIN 60P
D256 8-719-938-67 s LED GL3EG8
D257 8-719-938-67 s LED GL3EG8
D258 8-719-938-67 s LED GL3EG8
D101 8-719-016-74 s DIODE 1SS352
D259 8-719-938-68 s LED GL3HY8
D102 8-719-016-74 s DIODE 1SS352
D103 8-719-016-74 s DIODE 1SS352
D104 8-719-016-74 s DIODE 1SS352
D105 8-719-016-74 s DIODE 1SS352
D260 8-719-938-68 s LED GL3HY8
D261 8-719-938-67 s LED GL3EG8
D262 8-719-938-67 s LED GL3EG8
D263 8-719-938-67 s LED GL3EG8
D106 8-719-016-74 s DIODE 1SS352
D264 8-719-938-68 s LED GL3HY8
D107 8-719-016-74 s DIODE 1SS352
D108 8-719-016-74 s DIODE 1SS352
D269 8-719-938-68 s LED GL3HY8
D109 8-719-016-74 s DIODE 1SS352
D110 8-719-016-74 s DIODE 1SS352
D111 8-719-016-74 s DIODE 1SS352
D112 8-719-016-74 s DIODE 1SS352
D113 8-719-016-74 s DIODE 1SS352
D114 8-719-016-74 s DIODE 1SS352
D115 8-719-016-74 s DIODE 1SS352
D116 8-719-016-74 s DIODE 1SS352
D117 8-719-016-74 s DIODE 1SS352
D118 8-719-016-74 s DIODE 1SS352
D201 8-719-016-74 s DIODE 1SS352
D204 8-719-016-74 s DIODE 1SS352
ND101 8-719-962-02 s LED GL-6P202
R101 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R102 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R103 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R104 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R105 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R106 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R107 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R108 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R109 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R110 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
D207 8-719-016-74 s DIODE 1SS352
D210 8-719-016-74 s DIODE 1SS352
D213 8-719-016-74 s DIODE 1SS352
D216 8-719-016-74 s DIODE 1SS352
D219 8-719-016-74 s DIODE 1SS352
D222 8-719-016-74 s DIODE 1SS352
D225 8-719-938-68 s LED GL3HY8
D226 8-719-938-67 s LED GL3EG8
D227 8-719-938-67 s LED GL3EG8
D228 8-719-938-67 s LED GL3EG8
D230 8-719-938-68 s LED GL3HY8
D231 8-719-938-67 s LED GL3EG8
D232 8-719-938-67 s LED GL3EG8
D233 8-719-938-67 s LED GL3EG8
D234 8-719-938-68 s LED GL3HY8
D235 8-719-938-68 s LED GL3HY8
D236 8-719-938-67 s LED GL3EG8
D237 8-719-938-67 s LED GL3EG8
D238 8-719-938-67 s LED GL3EG8
D239 8-719-938-68 s LED GL3HY8
D240 8-719-938-68 s LED GL3HY8
D241 8-719-938-67 s LED GL3EG8
D242 8-719-938-67 s LED GL3EG8
D243 8-719-938-67 s LED GL3EG8
D244 8-719-938-68 s LED GL3HY8
D245 8-719-938-68 s LED GL3HY8
D246 8-719-938-67 s LED GL3EG8
D247 8-719-938-67 s LED GL3EG8
D248 8-719-938-67 s LED GL3EG8
D249 8-719-938-68 s LED GL3HY8
R111 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R112 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R113 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R114 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R115 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R116 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R117 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R118 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R119 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R120 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R121 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R122 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R123 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R124 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R125 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R126 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R127 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R128 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R129 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R130 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R131 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R132 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R133 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R134 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R135 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R136 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R137 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R138 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R139 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
R140 1-216-037-00 s RESISTOR,CHIP 330 1/10W(2012)
HKDV-900
3-13
Page 48
(CP-365 BOARD suffix 11, 12)
(CP-365 BOARD suffix 11, 12)
Ref. No.
or Q’ty Part No. SP Description
R141 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R142 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R143 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
Ref. No.
or Q’ty Part No. SP Description
R255 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R256 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R301 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R144 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R145 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
S101 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S102 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R201 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R202 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R203 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S103 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S104 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S105 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R204 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R205 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
S106 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S107 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R206 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R207 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R208 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S108 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S109 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S110 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R209 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R210 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S111 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S112 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R211 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R212 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R213 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
S113 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S114 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S115 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R214 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R215 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S116 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S117 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R216 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R217 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R218 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
S118 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S201 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S202 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R219 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R220 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
S203 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S204 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R221 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R222 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R223 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
S205 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S206 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
S207 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R224 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R225 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
S208 1-692-537-11 s SWITCH, TACTILE (WITH LIGHT)
R226 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R227 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R228 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R229 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R230 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R231 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R232 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R233 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R234 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R235 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R236 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R237 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R238 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R239 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R240 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R241 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R242 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R243 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012)
R244 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R245 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R246 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R247 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R248 1-216-027-00 s RESISTOR,CHIP 120 1/10W(2012)
R249 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R250 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R251 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012)
R252 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R253 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
R254 1-216-051-00 s RESISTOR,CHIP 1.2K 1/10W(2012)
3-14
HKDV-900
Page 49
----FRAME
---- Ref. No.
or Q’ty Part No. SP Description
1pc! 1-794-177-11 s INLET, AC (WITH FILTER)
8pcs1-466-955-11 s ENCODER, ROTARY
HN1011-960-733-11 o HARNESS, SUB (CP-CP)
(CN400/CP-364 board to CN1/CP-365 board)
HN1021-960-733-11 o HARNESS, SUB (CP-CP)
(CN401/CP-364 board to CN2/CP-365 board)
HN103 ! 1-960-732-11 o HARNESS, SUB (DC-CP)
(CN600/CP-364 board to SWITCHING REGULATOR)
HN104 ! 1-960-729-11 o HARNESS, SUB (AC-SW)
(SWITCHING REGULATOR to AC INLET)
HN105 ! 1-960-730-11 o HARNESS, SUB (AC-GND1)
(AC INLET to GND)
HN106 ! 1-960-731-11 o HARNESS, SUB (AC-GND2)
(SWITHING REGULATOR to GND)
S1! 1-762-954-11 s SWITCH, POWER
3-4.Packing Materials & Supplied
Accessories
Ref. No.
or Q’ty Part No. SP Description
4pcs 7-682-578-09 s SCREW +B5X16
4pcs 7-688-005-02 s WASHER (5)
3-5.Power Cords
Part No. SP Description
<For the customers in Japan>
1pc—————— DK-2401
1pc! 1-793-461-11 o PLUG, CONVERSION (3P-2P)
1pc3-613-640-01 o HOLDER (C), PLUG
<For the customers in the U.S.A. and Canada>
1pc! 1-557-377-11 s CORD, POWER
1pc3-613-640-01 o HOLDER (C), PLUG
<For the customers in the United Kingdom>
1pc! 1-782-929-11 o CORD, POWER (BS 3P)
1pc3-613-640-01 o HOLDER (C), PLUG
HKDV-900
3-15
Page 50
Page 51
Section 4
Semiconductor Pin Assignments
The following describes the semiconductor types used in
this unit.
For semiconductors marked with page numbers in the
index, refer to the corresponding pages in this section.
However, in some cases incompatible types are also listed,
therefore, when a part is to be replaced, also refer to the
Spare Parts section.
In addition, for semiconductors with ID Nos., refer to the
separate CD-ROM titled “Semiconductor Pin Assignments”
(Sony Part No. 9-968-546-xx) that allows searching for
parts by semiconductor type or ID No.
The semiconductors in the manual or on the CD-ROM are
listed by equivalent types. Thus the external view or the
index mark indication may differ from the actual type.
Pin assignments and block diagrams are based on the IC
manufacturer’s data book.
AS
AS2H
AS2L
ASHH
ASHL
ASLH
ASLL
E
E1A,CE1B,CE2A,CE2B
CKE
S0
-
CS6
DQMLL
DQMLU
DQMUL
DQMUU
CIORD
CIOWR
RQOUT
E
AS
AS2
D
RD/
WR
SCK
STATUS0, STATUS1
TXD
E0
-
WE3
XTAL
XTAL2
INPUTS/OUTPUTS
CKIO
D0 - D31
PORT0 - PORT7
TCLK
OTHERS
GND (PLL)
GND (RTC)
NC
V
CC
(PLL)
V
CC
(RTC)
FUNCTION OVERVIEWS
.CPU
.CACHE MEMORY
.MEMORY MANAGEMENT UNIT
.32-BIT TIMER UNIT (3-CHANNEL)
.WATCHDOG TIMER
.SERIAL COMMUNICATION INTERFACE
.REFRESH CONTROLLER
.RTC (REALTIME CLOCK)
: BUS REQUEST
: CHIP ACTIVE
: EXTERNAL CLOCK/CRYSTAL RESONATOR
: CRYSTAL RESONATOR (FOR ON-CHIP RTC)
: IO 16-BIT INSTRUCTION
: EXTERNAL INTERRUPT SOURCE
: OPERATING MODE
: NONMASKABLE INTERRUPT REQUEST
: RESET
: SERIAL DATA
: HARDWARE WAIT REQUEST
: ADDRESS BUS
: BUS ACKNOWLEDGE
: BUS CYCLE START
: EXTERNAL CAPACITANCE (FOR PLL1)
: COLUMN ADDRESS STROBE (FOR SDRAM)
: D8 - D15 SELECT SIGNAL (FOR AREA2 DRAM)
: D0 - D7 SELECT SIGNAL (FOR AREA2 DRAM)
: D24 - D31 SELECT SIGNAL (FOR DRAM)
: D16 - D23 SELECT SIGNAL (FOR DRAM)
: D8 - D15 SELECT SIGNAL (FOR DRAM)
: D0 -D7 SELECT (FOR DRAM)
: CHIP ENABLE (FOR PSEUDO-SRAM)
: CHIP ENABLE (FOR PCMCIA)
: CLOCK ENABLE CONTROL (FOR SDRAM)
: CHIP SELECT
: D0 -D7 SELECT SIGNAL (FOR SDRAM)
: D8 - D15 SELECT SIGNAL (FOR SDRAM)
: D16 - D23 SELECT SIGNAL (FOR SDRAM)
: D24 - D31 SELECT SIGNAL (FOR SDRAM)
: IO READ (FOR PCMCIA, PCMCIB)
: IO WRITE (FOR PCMCIA, PCMCIB)
: INTERRUPT REQUEST NOTIFICATION
: OUTPUT ENABLE (FOR PSEUDO-SRAM)
: ROW ADDRESS STROBE (FOR DRAM, SDRAM)
: ROW ADDRESS STROBE (FOR AREA DRAM)
: READ PULSE (FOR PCMCIA, NORMAL MEMORY)
: READ/WRITE (FOR DRAM, SDRAM, PCMCIA)
: SERIAL CLOCK
: PROCESSOR STATUS
: SERIAL DATA
: WRITE ENABLE (FOR NORMAL MEMORY, PSEUDO-SRAM)
: CRYSTAL RESONATOR
: CRYSTAL RESONATOR (FOR ON-CHIP RTC)
: SYSTEM CLOCK
: DATA BUS
: IO PORT
: TIMER EXTERNAL CLOCK INPUT/RTC CLOCK OUTPUT
: PLL GROUND
: RTC OSCILLARTOR GROUND
: NO CONNECTION
: PLL POWER SUPPLY (3.3V)
: RTC OSCILLATOR POWER SUPPLY (3.3V)
4-2
HKDV-900
Page 53
HN58X2464FPSRZ (HITACHI)
64K-BIT SERIAL INTERFACE EEPROM
TOP VIEW
A0 IN
A1 IN
A2 IN
GND
1
2
3
4
8
7
6
5
V
CC
WP IN
SCL IN
SDA I/O
LTC1625CGN-E2 (LINEAR TECH)
SWTCHING REGULATOR
—TOP VIEW—
1
EXTV
SYNC
RUN/SS
S.GND
OSENSE
V
V
PROG
FCB
CC
2
3
4
TH
I
5
6
7
8
16
15
14
13
12
11
10
9
V
IN
TK
SW
TG
BOOST
INTV
BG
P.GND
CC
INPUTS
A0 - A2
: ADDRESS
SCL
: SERIAL CLOCK
WP
: WRITE PROTECT
INPUT/OUTPUT
SDA
: SERIAL DATA
INPUTS
: TOPSIDE FLOATING DRIVER SUPPLY
BOOST
: INTV
CC
CC
EXTV
FCB
TH
I
RUN/SS
SW
SYNC
TK
IN
V
V
OSENSE
V
PROG
OUTPUTS
BG
CC
INTV
TG
SWITCH
: FORCED CONTINUOUS
: ERROR AMPLIFIER COMPENSATION POINT
: RUN CONTROL/SOFT START
: SWITCH NODE
: SYNC
: TOP MOSFET KELVIN SENSE
: MAIN POWER SUPPLY
: OUTPUT VOLTAGE SENSE
: OUTPUT VOLTAGE PROGRAMMING
: BOTTOM GATE DRIVE
: INTERNAL 5.2 V REGULATOR
: TOP GATE DRIVE
C720 *F1
C721 *F1
C722 *F1
C723 F1
C724 F1
C725 F1
C726 F1
C727 F1
C728 F1
C729 F1
C730 F1
C731 *F2
C732 *F2
C733 *F2
C734 *F2
C735 *F2
C736 F2
C737 F2
C738 F2
C739 F1
C740 F1
C741 F2
C742 F1
C743 F1
C721 *F1
C722 *F1
C723 F1
C724 F1
C725 F1
C726 F1
C727 F1
C728 F1
C729 F1
C730 F1
C731 *F2
C732 *F2
C733 *F2
C734 *F2
C735 *F2
C736 F2
C737 F2
C738 F2
C739 F1
C740 F1
C741 F2
C742 F1
C743 F1
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
SAFETY CHECK-OUT
After correcting the original service problem,
perform the following safety checks before
releasing the set to the customer :
Check the metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC
leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to
earth ground and from all exposed metal parts to
any exposed metal part having a return to
chassis, must not exceed 3.5 mA. Leakage
current can be measured by any one of three
methods.
1. A commercial leakage tester, such as the
Simpson 229 or RCA WT-540A. Follow the
manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The
Data Precision 245 digital multimeter is
suitable for this job.
3. Measuring the voltage drop across a resistor
by means of a VOM or battery-operated AC
voltmeter. The “limit” indication is 5.25 V, so
analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa
SH-63Trd are examples of a passive VOM
that is suitable. Nearly all battery operated
digital multimeters that have a 20 V AC range
are suitable. (See Fig. A)