• HCD-XGV6/XGV8/XGV10AV are the
Amplifier, CD player, tape deck and
tuner section in LBT-XGV6/XGV8/
XGV10AV.
Photo : HCD-XGV10AV
Model Name Using Similar MechanismNEW
CDCD Mechanism TypeCDM37B-30BD62
SectionBase Unit NameBU-30BD62
Optical Pick-up NameA-MAX.3
TAPE
Section
Model Name Using Similar MechanismHCD-XGR90AV
E Model
Amplifier section
LBT-XGV10AV
Front Speaker:
The following measured at AC 120/220/240 V, 50 Hz
DIN power output (Rated)150 + 150 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
200 + 200 watts
(6 ohms at 1 kHz, 10% THD)
Center Speaker:
DIN power output (Rated)35 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
50 watts
(8 ohms at 1 kHz, 10% THD)
Rear Speaker:
DIN power output (Rated)35 + 35 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
50 + 50 watts
(8 ohms at 1 kHz, 10% THD)
LBT-XGV8
The following measured at AC 120/220/240V, 50 Hz
DIN power output (rated)125W x 2 + 125W x 2
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
170 W x 2 + 170 W x 2
(6 ohms at 1 kHz, 10% THD)
SPECIFICATIONS
LBT-XGV6
The following measured at AC 120/220/240V, 50 Hz
DIN power output (rated)150 + 150 watts (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
Outputs
PHONES:
(stereo phone jack)accepts headphones of 8 ohms or more
MD (VIDEO) OUT:
(phono jacks)voltage 250 mV
impedance 1 kilohms
LBT-XGV10AV
WOOFER OUT (phono jack):voltage 1 V, impedance 1 kilohm
FRONT SPEAKER:accepts impedance of 6 to 16 ohms
CENTER SPEAKER:accepts impedance of 8 to 16 ohms
REAR SPEAKER:accepts impedance of 8 to 16 ohms
LBT-XGV8
FRONT SPEAKER:accepts impedance of 6 to 16 ohms
(SUPER WOOFER)
accepts impedance of 6 to 16 ohms
(TWEETER & WOOFER)
LBT-XGV6
FRONT SPEAKER:accepts impedance of 6 to 16 ohms
Video section
Inputs
GAME INPUT (phono jack):1 V p-p, 75 ohms
Outputs
VIDEO OUT (phono jack):1 V p-p, 75 ohms
VIDEO CD/CD player section
SystemCompact disc and digital audio system
LaserSemiconductor laser
(λ=795nm), Emission
duration: continuous
Frequency response2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratioMore than 90 dB
Dynamic rangeMore than 90 dB
Video color system formatNTSC, PAL
(with the interval set at 9 kHz)
Other models:531 – 1,602 kHz
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
AntennaAM loop antenna
Antenna terminalsExternal antenna terminal
Intermediate frequency450 kHz
General
Power requirements
Saudi Arabian model:120 – 127 V, 220 V or 230 – 240 V AC,
50/60 Hz
Adjustable with voltage selector
2
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
Page 3
HCD-XGV6/XGV8/XGV10AV
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY .
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
• MODEL IDENTIFICATION
– Rear Panel –
PART No.
MODEL
XGV10AV : SP model
XGV10AV : TH model
XGV8 : SP model
XGV6 : TH model
XGV6 : SP model
XGV10AV : EA model
• Abbreviation
SP : Singapore model
TH: Thai model
EA: Saudi Arabia model
8-1. Case,Back Panel Section ··················································· 66
8-2. Front Panel Section-1 ························································ 67
8-3. Front Panel Section-2 ························································ 68
8-4. Chassis Section ·································································· 69
8-5. CD Mechanism Deck Section
(CDM37B-30BD62)··························································· 70
8-6. Base Unit Section (BU-30BD62) ······································71
9. ELECTRICAL PARTS LIST ······································· 72
3
Page 4
HCD-XGV6/XGV8/XGV10AV
SECTION 1
SERVICING NOTE
JIG FOR CHECKING PROLOGIC BOARD (XGV10AV ONLY)
The special jig (J-2501-216-A) is useful for checking the PROLOGIC board.
CN201
PROLOGIC board
MAIN board
Jig (J-2501-216-A)
CN202
CN152
CN151
4
Page 5
Main unit
ALPHABETICAL ORDER
SECTION 2
GENERAL
HCD-XGV6/XGV8/XGV10AV
This section is extracted from
instruction manual.
A — D
A EJECTZ/ Z B EJECT wl
ALBUM +/— ed
CD SYNC ql
Direct equalizer qh r;
POP/ROCK/JAZZ/DANCE/
GAME
SALSA/REGGAE/TANGO/
SAMBA/MOVIE
DIRECTION ek
DISC SKIP eg
DISC 1 to 5 es
DISPLAY 2
DSP ra (XGV10AV)
DVD 5.1CH wg (XGV10AV)
E — K
ECHO LEVEL ej
EDIT ef
EFFECT 5
ENTER 5
FM MODE 8
FUNCTION qd
GAME qf
GAME INPUT AUDIO L/R jacks
wf
GAME INPUT VIDEO jack wf
GAME MIXING qg
GROOVE ra
H SPEED DUB ql
KARAOKE PON/MPX ea
KEY CONTROL #/ 2 ea
234 576890 qa qs
1
M — R
MIC LEVEL ej
MIC 1/2 jacks eh
NEXT wd
P FILE 5
PHONES jack w;
PICTURE EFFECT wd
PLAY MODE eg
POWER SAVE/DEMO
(STANDBY) 3
Power stream indicator 6
PREV wd
PRO LOGIC wg (XGV10AV)
PUSH OPEN wk
REPEAT eg
RETURN Owd
qd
ra
r;
el
ek
ej
eh
eg
ef
wk
qf
qg
qh
qj
qk
ql
w;
wa
ws
wd
wfwgwhwjwle;eaesed
5
Page 6
HCD-XGV6/XGV8/XGV10AV
This section is extracted from
instruction manual.
S — X
SELECT wd
SLEEP 0
SPECTRUM ANALYZER 4
SUPER WOOFER ra
SUPER WOOFER MODE ra
SURROUND (XGV6, XGV8) ra
TIMER SELECT qa
TUNER/BAND 9
TUNER ENTER wh
TUNER MEMORY wh
TUNING MODE 8
TUNING —/+ 9
VOLUME control 7
X-GROOVE wj
BUTTON DESCRIPTIONS
@/1 1
c/CLOCK SET qs
h/H qj el
x qjel
.m /M> qjel
X qk
z REC qk
.AMS> wa
HX ws
x ws
m /M ws
R/r/T/t (cursor) e;
Remote control
ALPHABETICAL ORDER
A—E
ALBUM +/— eg
CD N wl
CENTER LEVEL +/— w;
CLEAR 6
CLOCK/TIMER SELECT r;
CLOCK/TIMER SET 1
DISC SKIP ef
DISPLAY eh
DSP wh
DVD 5.1CH wg
EFFECT q;
ENTER ws
F—R
FILE SELECT +/— qf
FUNCTION +/— ea
KEY CONTROL #/ 2 ql
NEXT wj
Numeric buttons ej
ON SCREEN ek
PICTURE EFFECT 9
PLAY MODE ed
PRESET —/+ wj
PREV wj
PRO LOGIC wf
REAR LEVEL +/— qh
REPEAT es
RETURN O qa
(For XGV10AV)
S—V
SELECT wl
SLEEP el
SPECIAL MENU 8
TAPE A nN e;
TAPE B nN qg
TEST TONE wd
TUNER/BAND wk
TUNING —/+ qj
TV CH +/— 5
TV/VIDEO 7
TV VOL +/— 4
TV @/1 2
VOL +/— qk
BUTTON DESCRIPTIONS
@/1 3
X qs
x qd
m /M qj
R/r/T/t (cursor) wa
./> wj
r;
el
ek
ej
1
2
3
4
eh
eg
ef
ed
es
ea
e;
wl
wk
wj
wh
wg
wf
wd
ws
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
wa
ql
w;
6
Page 7
HCD-XGV6/XGV8/XGV10AV
This section is extracted from
instruction manual.
Remote control
ALPHABETICAL ORDER
A—F
ALBUM +/— es
CD Nwh
CLEAR 6
CLOCK/TIMER SELECT ej
CLOCK/TIMER SET 1
DISC SKIP ea
DISPLAY ed
EFFECT qf
ENTER wa
FILE SELECT +/— 9
FUNCTION +/— wk
G—R
GROOVE ws
KEY CONTROL #/ 2 ql
NEXT wd
Numeric buttons ef
ON SCREEN eg
PICTURE EFFECT wf
PLAY MODE e;
PRESET —/+ wd
PREV wd
REPEAT wl
RETURN Oq;
(F or XGV6,XGV 8 )
S—V
SELECT wh
SLEEP eh
SPECIAL MENU 8
SUPER WOOFER qj
SURROUND qg
TAPE A nN wj
TAPE B nN qd
TUNER/BAND wg
TUNING —/+ qh
TV CH +/— 5
TV/VIDEO 7
TV VOL +/— 4
TV @/12
VOL +/— qk
BUTTON DESCRIPTIONS
@/1 3
X qa
x qs
m /M qh
R/r/T/t (cursor) w;
./> wd
ej
eh
1
2
eg
ef
ed
es
ea
e;
wl
wk
wj
wh
wg
wf
wd
ws
wa
w;
3
4
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
ql
7
Page 8
HCD-XGV6/XGV8/XGV10AV
)
SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.
SetCaseFront panel sectionTape mechanism deck
Back panel, DC fan, MAIN board, PROLOGIC board (XGV10), VIDEO board
CD mechanism deck (CDM37B-30BD62)
PANEL FL board, TC-A board, TC-B board
PANEL VR board
MIC/GUITAR board, HEADPHONE board
FRONT INPUT board
D-SW board, CD-L board, Lid (CD) assy, CD-R board
Base unit-1 (BU-30BD62)
Disc table
Note : Follow the disassembly procedure in the numerical order given.
3-1. CASE
8
Case
7
1
Three screws
(CASE3 TP2)
5
Base unit-2 (BU-30BD62)BD board
3
Five screws (BVTT 3
×
6)
4
Two screws (BVTP 3
×
8
6
6
5
2
Three screws (CASE3 TP2)
8
Page 9
HCD-XGV6/XGV8/XGV10AV
)
k
3-2. FRONT PANEL SECTION
2
Flat type wire (CN431)
3
Connector (CN311)
7
Screw (BVTP 3 X 8)
8
Lug
4
Connector (CN903)
5
Connector (CN722)
1
(CN371)
9
0
6
Connector (CN806)
qa
Connector (B deck)
Flat type wire
Screw (BVTP 3 X 8
Lug
qg
Front panel section
3-3. TAPE MECHANISM DECK
qd
Four screws (BVTP 3 X 8)
qs
Screw (BVTP 3 X 8)
qf
Claw
1
Flat type wire (15 core)
4
2
Two screws
(BVTP 2.6 X 8)
3
Two screws
(BVTP 2.6 X 8)
Front panel
5
Tape mechanism dec
9
Page 10
HCD-XGV6/XGV8/XGV10AV
y
3-4. PANEL FL BOARD, TC-A BOARD, TC-B BOARD
w;
TC-A board
1
Screw (BVTP 2.6 X 8)
2
3
Bracket (TA)
Lug
qh
Three claws
qa
Five screws (BVTP 2.6 X 8)
qs
Three screws
(BVTP 2.6 X 8)
qk
PANEL FL board
ql
Two claws
0
Two knobs (MIC)
3-5. PANEL VR BOARD
qj
6
Connector
(CN812)
wa
Two claws
Front panel
qf
Four screws
(BVTP 2.6 X 8)
7
Connector
(CN704)
4
Screw
(BVTP 2.6 X 8)
5
Bracket (TA)
qd
Eight screws
(BVTP 2.6 X 8)
9
Flat type wire
(CN601)
qg
(BVTP 2.6 X 8)
ws
TC-B board
8
Connector (CN703)
Four screws
3
Bracket (TA)
4
Knob (VOLUME)
2
Lug
1
Screws
(BVTP 2.6 X 8)
7
0
Eight screws
(BVTP 2.6 X 8)
6
5
Flat type wire
(CN701)
8
(BVTP 2.6 X 8)
9
Lever (EJECT) ass
qa
Nine screws
(BVTP 2.6 X 8)
qs
PANEL VR board
Preess the two buttons (EJECT)
Two screws
10
Front panel
Page 11
3-6. MIC/GUITAR BOARD, HEADPHONE BOARD
t
)
1
Connector
(CN812)
HCD-XGV6/XGV8/XGV10AV
2
Two screws
(BVTP 2.6 X 8)
3
MIC bracket
4
MIC/GUITAR board
5
Two screws
(BVTP 2.6 X 8)
6
HEADPHONE bracke
3-7. FRONT INPUT BOARD
Front panel
FRONT INPUT board
J804
Front panel
7
HEADPHONE board
2
Bumper (Panel)
1
Four screws
(BVTP 2.6 X 8
Front panel
4
3
FRONT INPUT board
11
Page 12
HCD-XGV6/XGV8/XGV10AV
d
)
3-8. D-SW BOARD, CD-L BOARD, LID (CD) ASSY, CD-R BOARD
5
0
Spring (CD)
qa
Lid (CD) assy
9
Sub panel (CD-L) assy
8
CD-L board
7
Four screws
(BVTP 2.6 X 8)
3
Connector
(CN704)
Two screws
(BVTP 2.6 X 8)
6
4
(BVTP 2.6 X 8)
ql
Sub panel
(CD-R) assy
qd
Knob
(CD)
Two screws
qh
qk
CD-R board
qg
Two screws
(BVTP 2.6 X 8)
qs
Connector (CN703)
1
Screw (BVTP 2.6 X8)
2
D-SW boar
qf
Two screws
(BVTP 2.6 X 8)
qj
Four screws
(BVTP 2.6 X 8)
3-9. BACK PANEL, DC FAN, MAIN BOARD, PROLOGIC BOARD (XGV10), VIDEO BOARD
1
Flat type wire (CN441)
7
qd
qa
Flat type wire
(CN401)
Connector (CN102)
XGV8/XGV10
Back panel
q;
DC FAN
(M901)
6
wa
qs
Connector (CN441)
wh
VIDEO board
wf
Connector (CN301)
Flat type wire (CN101)
ws
2
Eight screws
(BVTP 3 X 8)
qk
qg
(CN901, 902)
3
Four screws
(BVTP 3 X 8)
9
Two screws
(BVTP 3 X 8)
5
Four screws
(BVTP 3 X 8)
4
Three screws
(BVTP 3 X 8)
ql
PROLOGIC board
qj
Two connectors
(CN151, 152)
8
Connector (CN961
qh
MAIN board
qf
Two screws
(BVTP 3 X 8)
Two connectors
XGV10
12
w;
Two screws
(BVTP 3 X 8)
wd
Flat type wire
(CN201)
wg
Two screws
(BVTP 3 X 8)
Page 13
3-10. CD MECHANISM DECK (CDM37B-30BD62)
1
Flat type wire
(CN401)
4
Three screws
(BVTP 3 X 8)
7
2
Connector
(CN411)
6
Two screws (BVTP 3 X 8)
8
7
HCD-XGV6/XGV8/XGV10AV
3
Four screws (BVTP 3 X 8)
Wire holder
5
Two screws
(BVTP 3 X 8)
qa
CD mechanism deck
(CDM37B-30BD62)
0
Five screws
(BVTP3 × 8)
9
Remove two cables from
wire holder.
13
Page 14
HCD-XGV6/XGV8/XGV10AV
w
)
3-11. BASE UNIT-1 (BU-30BD62)
2
Boss
3
Base unit
(BU-30BD62)
1
BU fitting scre
3-12. BASE UNIT-2 (BU-30BD62)
1
Two floating screws (DIA.12)
4
Two coil springs
(insulator)
6
Base unit (BU-30BD62)
2
Two screws
(BVTP 2.6 X 8)
3
Two stoppers
(BU)
14
5
Two coil
springs
(insulator
Holder (BU30) assy
Page 15
3-13. BD BOARD
e
4
BD board
HCD-XGV6/XGV8/XGV10AV
BU-30BD62
3
Flat type wire (CN102)
1
Remove the two solders.
3-14. DISC TABLE
Note: When the disc table is installed, adjust the positions of roller cam
and mark B as shown in the figure, then set to the groove of disc
table.
A
1
Screw (BVTP 3
2
Remove the two solders.
×
8)
2
Bracket (BU)
3
Step screw
4
Disc tabl
A
15
Page 16
HCD-XGV6/XGV8/XGV10AV
B
SECTION 4
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1.Turn the power ON or set to the DEMO mode.
2.Press three buttons of c/CLOCK SET , TUNER ENTER , and
\/1 simultaneously.
3. The set is reset, and displays “COLD RESET”, then becomes
DEMO mode.
[Change-over the AM Tuning Interval]
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1.Press the \/1 button to turn the power ON.
2.Select the function “TUNER”, and press the TUNER/BAND
button to select the BAND “AM”.
3. Press the \/1 button to turn the power OFF.
4. Press the ENTER/NEXT and \/1 buttons simultaneously,
and the display on the fluorescent indicator tube changes to
“AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning
interval is changed over.
[CD Ship Mode] (No memory clear)
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1.Press the \/1 button to turn the power ON.
2. Press the EDIT and
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Procedure:
1. Press three buttons of c/CLOCK SET , ENTER/NEXT ,
and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3.Press the DISC 1 button, the MODE and DESTINATION are
displayed fluorescent indicator tube.
4.Each time the DISC 1 button is pressed, the MC/GC category
version is displayed in the following order.
5.Press the DISC 2 button, and the key check mode is acti-vated.
NRMCGCCDCDDMCDMA
6. In the key check mode, the fluorescent indicator tube displays
“K 0 J0 V0”. Each time a button is pressed, “K” value in-creases
to “K69”call the button is pressed.However, once a button is
pressed, it is no longer taken into account.
“J” value increases like 1, 2, 3 ... if turn the . AMS > JOG
dial clock-wise,or it decreases like 0, 9, 8 ... if turn the
. AMS > JOG dial counter-clockwise.
“V” value increases like 1, 2, 3 ... if turn the VOLUME dial
clockwise (“+” direction), or it decreases like 0, 9, 8 ... if turn the
VOLUME dial counterclockwise (“–” direction).
7. To release from this mode, press three buttons in the same
manner as step 1, or disconnect the power cord.
buttons simultaneously.
\/1
BDABDBSTTATMTC
CDM
[Sled Servo Mode] (CD service mode)
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons c/CLOCK SET , TUNER ENTER , and
DISC 5 simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press M button in CD section to
move the pick-up to outside track, or m button to inside track.
5. T o exit from this mode, press
Note:
• Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[Change-over of FUNCTION Name]
• The FUNCTION name of external input terminal can be changed
over to VIDEO or MD. W ith the FUNCTION selected to “MD”,
about 5dB mute is applied to the input gain.
Procedure:
1. Press \/1 button to turn the power OFF.
2. Press
several seconds, and the power is turned on, the display of
fluorescent indicator tube changes to “MD” or “VIDEO”
instantaneously, and thus the FUNCTION is changed over.
[Aging Mode]
This mode can be used for operation check of tape deck section.
Tape deck section work in parallel.
• If an error occurred:
The aging operation stops and display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1.Load the tapes into the decks A and B respectively.
2.Press the FUNCTION button to select the function “CD”.
3.Press the PLAY MODE button to set the “ALL DISCS” mode,
and press the REPEAT button to “REPEAT” off.
4. Press three buttons of c/CLOCK SET , TUNER ENTER ,
and DISC 4 simultaneously.
5. The aging mode is activated, if the indicator of disc tray number on the fluorescent indicator tube is blinking.
6. To release from the aging mode, press the \/1 button to turn
the power OFF and operate the cold reset. (Refer to the “MC
Cold Reset”)
1. Display at the Aging Mode
• Display operating state of tape deck section alternately.
• If an error occurred, stop display.
button together with FUNCTION button for
\/1
button turn to the power OFF .
\/1
16
Page 17
HCD-XGV6/XGV8/XGV10AV
2. Tape Deck Section
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
Aging mode sequence (Tape deck section):
Rewind the tape A
“T APE A AG-1”
Shut off
FWD the tape A
“T APE A AG-2”
2 minutes
Fast forward the tape A
“T APE A AG-3”
Shut off or 20 seconds
RVS the tape A
“T APE A AG-4”
2 minutes
Rewind the tape A
“T APE A AG-5”
Shut off
3. CD Section
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
Aging mode sequence (CD section):
Tray Turn
DISC 1
chucking
TOC Read
Track 1 Play
2 seconds
Last Track Play
2 seconds
FWD the tape B
“TAPE B AG-2”
2 minutes
Fast forward the tape B
“TAPE B AG-3”
Shut off or 20 seconds
RVS the tape B
“TAPE B AG-4”
2 minutes
Rewind the tape B
“TAPE B AG-5”
Shut off
Note:“TAPE * AG- * ” is display of each step.
Tray T un
DISC 4
Chucking
TOC Read
Track 1 Play
2 seconds
Last Track play
[VACS ON/OFF]
• The volume control by VACS is turned ON/OFF.
Procedure:
1.Press the \/1 button to turn the power ON.
2.Press the PLAY MODE and \/1 buttons simultaneously.
3.The reaction display appears when switcing ON/OFF.
17
Page 18
HCD-XGV6/XGV8/XGV10AV
SECTION 5
MECHANICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
Torque Measurement
ModeTorque MeterMeter Reading
2.9~6.9 mN•m
FWD(30 to 70 g•cm)
CQ-102C
FWD
back tension (2 to 6 g•cm)
FF/REW CQ-201B (80 to 170 g•cm)
(0.42 – 0.97 oz•inch)
0.19~0.59 mN•m
(0.03 – 0.08 oz•inch)
7.8~16.7 mN•m
(1.11 – 2.36 oz • inch)
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION 0 DB = 0.775 V
Precaution
1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless other-wise
specified.
8. Set to the DOLBY NR OFF.
9. Set to the test mode.
(1) Press the \/1 button to turn the power ON.
(2) Select the function “TAPE A or B”.
(3) Press the button of c/CLOCK SET , TUNER ENTER ,
and DISC 3 simultaneously, to set the tape deck test mode
and displays “TEST MODE” on the fluorescent indicator
tube.
(4) To release from the test mode, press the \/1 button.
• T est Tape
TapeSignalUsed for
P-4-A10010 kHz, – 10 dBAzimuth Adjustment
WS-48B3 kHz, 0 dBTape Speed Adjustment
18
Page 19
HCD-XGV6/XGV8/XGV10AV
)
Record/Playback Head Azimuth Adjustment
DECK A DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback (FWD)
test tape
P-4-A100
(10 kHz, – 10 dB)
MAIN board
MD (VIDEO) OUT jack (J701
L-CH, R-CH
level meter
set
+
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
Output
level
within
1dB
L-CH
peak
R-CH
peak
within
1dB
Screw
position
L-CH
peak
Screw
position
R-CH
peak
3. Mode: Playback
MAIN board
test tape
P-4-A100
(10 kHz, – 10 dB)
L-CH
set
R-CH
MD (VIDEO) OUT jack (J701)
L-CH
R-CH
oscilloscope
H
V
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck
B).
forward
reverse
Tape Speed Adjustment DECK B
Mode: Playback
test tape
WS-48B
(3 kHz, 0 dB)
set
MAIN board
MD (VIDEO) OUT jack (J701)
L-CH, R-CH
frequency counter
+
–
1. Insert the WS-48B into the deck B.
2. Press the H button on the deck B.
3. Press the H SPEED DUB button in playback mode.
Then at HIGH speed mode.
4. Adjust RV392 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
5. Press the H SPEED DUB button.
Then back to NORMAL speed mode.
6. Adjust RV391 on the LEAF SW board so that frequency
counter reads 3,000 ± 90 Hz.
Adjustment Location: MAIN board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
waveform of oscilloscope
in phase 45°90°135°180
good
wrong
°
4. Repeat step 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
19
Page 20
HCD-XGV6/XGV8/XGV10AV
e
r
r
REC Bias Adjustment DECK B
Procedure:
1. Mode: Record
FUNCTION: VIDEO
MAIN board
MD(VIDEO) IN jack (J701)
L-CH, R-CH
50 mV (– 23.8 dB)
600
Ω
blank tap
CS-123
AF OSC
1) 315 Hz
2) 10 kHz
attenuator
set
2. Mode: Playback
recorded
portion
set
MAIN board
CN301 pin
pin
level mete
1
(L-CH)
3
(R-CH)
+
–
3. Confirm playback the signal recorded in step 1 become specification values as follows.
If these values are out of specification values, adjust the RV321
(L-CH) and RV322 (R-CH) on the MAIN board to repeat
steps 1and 2.
Adjustment level: The playback output of 10kHz level difference
against 315 Hz reference should ±0.5 dB.
Adjustment Location: MAIN board
– MAIN BOARD (Component Side) –
REC Level Adjustment DECK B
Procedure:
1. Mode: Record
FUNCTION: VIDEO
MAIN board
MD (VIDEO) IN jack (J701)
L-CH, R-CH
AF OSC
315 Hz, 50 mV (– 23.8 dB)
600
Ω
blank tape
CS-123
attenuator
set
2. Mode: Playback
recorded
portion
set
MAIN board
CN301 pin
pin
level mete
1
(L-CH)
3
(R-CH)
+
–
3. Confirm playback the signal recorded in step 1 become specification values as follows.
If these values are out of specification values, adjust the RV351
(L-CH) and RV301 (R-CH) on the MAIN board to repeat steps
1 and 2.
Specification values:
CN301 playback level: 47.2 to 53.0 mV (– 24.3 to – 23.3 dB)
RV392
TAPE SPEED
(HIGH)
RV301
REC LEVEL
(R-CH)
RV351
REC LEVEL
(L-CH)
RV321
REC BIAS
(L-CH)
CN371
19
1
CN431
RV391
15
TAPE SPEED
1
(NORMAL)
IC501
IC301
3
1
CN301
RV322
REC BIAS
(R-CH)
IN
OUT
MD (VIDEO)
20
Page 21
HCD-XGV6/XGV8/XGV10AV
e
B=1.3 ± 0.6Vp-p
symmetry
A (DC voltage)
center of
waveform
B
0V
Specified level:× 100=less than – 22%
B
A
DVC
RFDC
RFAC
TE
FE
SE
DVC
CD SECTION
Note :
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use LUV-P01 (4-999-032-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the
following checks.
S-Curve Check
Oscilloscope
BD board
TP(FE)
TP(DVC)
Procedure :
1. Connect oscilloscope to TP (FE).
2. Connect between TP (FE) and TP (DVC ( 1.65 V)) by lead wire.
3. Press the \/1 button to turn the power ON.
4. Load a disc (LUV-P01) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus search)
5. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2
±0.5 Vp-p.
Note: Clear RF signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
VOLT/DIV : 200mV
TIME/DIV : 500ns
±
level : 1.45
0.3Vp-p
E-F Balance (1 Track jump) Check
oscilloscop
BD board
TP(TE)
TP(DVC)
Procedure:
1. Connect oscilloscope to TP (TE) and TP (DVC) board.
2. Press the \/1 button to turn the power ON.
3. Load a disc (LUV-P01) and playback the number nine track.
4. Press the bB button. (Becomes the 1track jump mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope
waveform.
S-curve waveform
symmetry
A
within 4
B
6. After check, remove the lead wire connected in step 2.
Note :• Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
RF Level Check
oscilloscope
BD board
TP(RFDC)
TP(RFAC)
Procedure :
1. Connect oscilloscope to TP (RFDC) and TP (RFAC).
2. Press the \/1 button to turn the power ON.
3. Load a disc (LUV-P01) and playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
±
1Vp-p
Checking Location:
[BD BOARD]
21
Page 22
HCD-XGV6/XGV8/XGV10AV
e
VIDEO SECTION
Note :
1. VIDEO board is basically designed to operate without adjustment. Therefore, check each item in order given.
2. Use HLX-504 (J-6090-088-A) or HLX-505 (J-6090-089-A)
unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the
following checks.
Video Level Adjustment (VIDEO BOARD)
Purpose
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.
Oscilloscop
75
Ω
set
J721
VIDEO OUTPUT
Procedure:
1. Connect oscilloscope to VIDEO output.
2. Load a disc (HLX-504 or HLX-505) playback.
3. Adjust the RV501 to attain 1.0±0.1Vp-p.
VIDEO BOARD (SIDE A)
CN101
CN301
IC508
IC505
RV501
VIDEO LEVEL
(WHITE 100%)
1.0 ± 0.1 Vp-p
22
Page 23
7-1. CIRCUIT BOARD LOCATION
HCD-XGV6/XGV8/XGV10AV
SECTION 7
DIAGRAMS
PANEL VR board
TC-A board
MIC/GUITAR board
CD-L board
PANEL FL board
CD-R board
TRANS board
SUB TRANS board
TUNER PACK
(FM/AM TUNER UNIT)
HEADPHONE board
FRONT INPUT board
TC-B board
MAIN board
SUB AMP board
(XGV8/XGV10)
PROLOGIC board
(XGV10)
PA board
VIDEO board
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
2
•
• 5 : fusible resistor.
• C : panel designation.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
• Voltages are taken with a VOM (Input impedance 10 MΩ).
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
• Abbreviation
: nonflammable resistor.
Note:
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
under no-signal conditions.
BD board section
no mark: CD PLAY
Other board section
no mark: TUNER (FM/AM)
( ): TAPE PLAY
< >: TAPE REC
[ ]: CD PLAY
Voltage variations may be noted due to normal production tolerances.
Voltage variations may be noted due to normal production tolerances.
F: TUNER (FM/AM)
E: TAPE PALY (DECK A)
d: TAPE PALY (DECK B)
G : RECORD
J: CD PALY (ANALOG OUT)
N: MIC INPUT
g : VIDEO
SP: Singapore model
TH: Thai model
EA: Saudi Arabia model
4
W or less unless otherwise
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
•: Pattern from the side which enables seeing.
(The other layers´ Patterns are not indicated.)
• Indication of transistor.
C
Q
B
E
Q
B
CE
B
• Abbreviation
SP: Singapore model
TH: Thai model
EA: Saudi Arabia model
These are omitted.
These are omitted.
Q
CE
These are omitted.
SENSOR board
D-SW board
MOTOR board
BD board
LED board
2323
Page 24
HCD-XGV6/XGV8/XGV10AV
7-2. BLOCK DIAGRAMS
– CD SERVO SECTION –
A
B
C
D
I-V AMP
F
E
OPTICAL PICK-UP BLOCK
(A-MAX.3)
LASER DIODE
LD
PD
TRACKING
COIL
FOCUS
COIL
S101
ON: when the optical pick-up
(
(LIMIT)
is inner position.
I5-10
PD1
PD2
I1-6
RF AMP,
FOCUS/TRACKING ERROR AMP
CD D+5V
A
6
B
7
C
8
D
9
F
11
F I-V AMP
E
10
E I-V AMP
LD
PD
LD
DRIVE
Q101
IC103
RF
SUMMING
AMP
∑
A-D
FOCUS
ERROR AMP
TRACKING
ERROR AMP
LD
APC LD
1
AMP
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
APC PD
AMP
43
EQ_IN
VDC
BUFFER
DC
AMP
26
RFC
RF EQ
AMP
RFACAC_SUM
RFDCO
RFDCI
VDC
IC102
VO4+
M101
SPINDLE
MOTOR
M102
SLED
MOTOR
T+
T-
F+
F-
5
M
10
1
M
2
56
55
52
47
VO4
VO3+
VO3
VO2
VO2+
VO1
VO1+
MOTOR
DRIVE
MOTOR
-
DRIVE
-
COIL
DRIVE
-
COIL
DRIVE
(
IN4
VREF
IN3+
IN3
IN2+
IN2
IN1+
IN1
STBY
23
22
27
26
32
31
35
34
8
DATA DECODERR,
D/A CONVERTOR
IC506
RST
Q102
RFAC
CLK
173
160
164
162
163
206
207
149
150
24
189
133
161
165
137
138
140
141
142
143
135
30
29
28
RFDC
FE
TE
SE
CLKA
CLKB
XTAI
XTAO
GPIO9
XTSL
MDP
CE
VC
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
SSTP
GPIO14
GPIO13
GPIO12
CD-DSP,
DIGITAL SERVO,
MPEG DECODER, DAC
IC505
GPIO0
GPIO1
GPIO2
GPIO3
13 14 15 16 18 19
SI
GPIO4
SO
SCK
SOK
SRQ
AUDDTO0
AUDLRCK
AUDBCK
GPIO11
AUDLRCK
DRDQM1
DRDQM0
DRWEL
DRDAT0
DRDAT15
DRADR0
DRADR10
SYS RST
GPIO5
SCS
DRRAS
DRCAS
15
28
29
FE
16
FEI
17
TE
18
14
SW
12
PD
2
TE
LD-ONFERFDC
5 93
AO4
RST
4 13 2
RST
AO6
AO3
AO2
AO1
HUE
SHARPNESS
6
DI
AO5
CLK
LD
12
11
10
X502
27MHz
X501
33.8688MHz
DATA
VRF
CPSIG
CSIA
NVOEL
DRCK
DRBS
I
I
81
RST
VIDEO LEVEL
+2.5V
3
201
204
203
26
205
6
7
74
78
77
70
76
72
68
73
49-56,
59-66
34-37,
39-45
RV501
Y
C
DATA
CLK
LAT
MCLK
A+5V
(5W)
16
65
VCC
DATA
2
I/F
LRCK
3
BLK
1
13
14
15
16
BAFFER
Q301
SYNC
DETECT
IC301
VIN
1
HUE CONTROL
17 18 20 38 15 39
WE
BA0
CAS
RAS
+3.3V
REG
Q581
CONTROL
DAC
DAC
D/A
CONVERTOR
IC504
VDD
LOUTCD-L
7
ROUT
8
IC102
5
3
SHARPNESS
CONTROL
LPF
IC304
V_INTHRU
10
DIFF
CONTROL
AMP
VIDEO
IN
63110
BURST
COLOR
SYNC
SEPA
BGP
VOUT
TINT
SYNC
OUT
5
6
8
V_OUT
1
PC
CONT
5
DELAY
IC302
IC303
ROM
DE
IC508
A0-A16 DQ0-DQ7
2-12,23,
13-15,
25-31
7-21
0-7
8-15
0-15
2,4,5,7,8,10,11,13,
42,44,45,47,48,50,51,53
DQ0-DQ15
SDRAM
IC507
CLK
LDQM
UDQM
34-37,
29-34
A0-A9
24
• R-ch is omitted due to same as L-ch.
• Signal Path
: CD PLAY (ANALOG)
: VIDEO
7
1
R-CM
BUFFER
Q302
(Page 26)
A
VIDEO AMP
IC307
Y/C MIX
(CD MECHANISM CONTROL)
BUF
IN
8
+
2
STB
+4.5V
(IC103)
Q370
+2.5V
+3.3V
V-MUTE
33
SQ-CLK
BU UP/DW SW
SYSTEM CONTROLLER
IC501 (1/4)
SQ-DATA
CD-DATA
XLT
CD-CLK
SCOR
HOLD
SCK
SOK
SCS
4036 37193243
SRQ
35
SI
SO
TBL-SENS
LED-DISK
MTR-CTRL1
MTR-CTR2
XRST
RST
31
RIPPLE FILTER
+2.5V REG
3
IC201
+3.3V REG
IC202
49
48
47
44
45
OUT
Q201
6
5
1
DISC TABLE
SENSOR
IC202
S201
(UP SWITCH)
LED DRIVE
Q201
Q412
Q411
VCD-VIDEO
G
D+5V
(SW)
(DISC No.)
TABLE MOTOR DRIVER
IC201
IN2
1
MOTOR
DRIVE
IN1
9
(Page 26)
D201
OUT2
OUT1
3
7
M201
M
(TABLE)
2424
Page 25
–TUNER/TAPE DECK SECTION –
DECK-A
R-CH
HCD-XGV6/XGV8/XGV10AV
IC341
+
HPF
MUTE
Q344,345
AMS DETECT
Q341-343
PB
HEAD
REC/PB
HEAD
ERASE
HEAD
FM
75Ω
AM
DECK-B
TC BLOCK
REC(REW)
REC(FWD)
B-PHOTO
A-PHOTO
B-MODE
A-MODE
B-HALF
A-HALF
A-SOL
B-SOL
CAP M+
MOTOR-L
MOTOR-H
CN371
ANTENNA
R-CH
R-CH
R-CH
C322,L321
RV321
REC
BIAS(L)
T331
FM/AM TUNER UNIT
ST-LOUT
FM ANT
FM ANT
AM ANT
AM ANT
ST-ROUT
ST-MUTE
STEREO
TUNED
OUT(ST-DIN)
IN(ST-DOUT)
ST-CLK
BIAS
TRAP
ST-CE
1
2
3
BIAS OSC
Q331,332
RIPPLE
FILTER
Q333
R-CH
ST-MUTE
STEREO
TUNED
ST-DIN
ST-DOUT
ST-CLK
ST-CE
REC/PB SWITCH
IC321
R-CH
TC A+10
ST-L
D
4
Q334,335
(Page 26)
SWITCH
Q321,322
Q383,384
A TRIG
DRIVE
Q381,382
B TRIG
DRIVE
Q385,386
CAP MOTOR
DRIVE
Q387,388
CAP MOTOR
SPEED CONT
RV391
RV392
32
34
21
RV931
TAPE SPEED
LOW
RV932
TAPE SPEED
HIGH
A
B
REC-OUT
70
120
DECK A/B SELECT
PB/REC EQUALIZER AMP
IC301
282726
A/B
NORM/HIGH
1312111514
ALC ON/OFF
PB-OUT1
ALC1
REC MUTE ON/OFF
MUTE ON/OFF
PB-L
RV351
REC(L)
LEVEL
23
(CD MECHANISM CONTROL)
REC-L
SYSTEM CONTROL
B
C
(Page 26)
(Page 26)
IC501(2/4)
53
AMS-IN
58
TC-MUTE
61
REC-MUTE
68
ALC
66
EQ-H/N
67
PB-A/B
BIAS
65
REC-B
50
REC-A
46
90
B-SHUT
A-SHUT
89
57
B-PLAY SW
56
A-PLAY SW
B-HALF
91
A-HALF
70
69
TC-RELAY
51
A-TRIG
52
B-TRIG
CAPM-CTRL
55
CAPM-H/L
54
ST-MUTE
21
STEREO
2
TUNED
3
ST-DIN
25
ST-DOUT
23
27
ST-CLK
ST-CE
22
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: TUNER (FM/AM)
: PLAYBACK (DECK A)
: PLAYBACK (DECK B)
: RECORD
1VBONot used (Connected to ground with capacitor)
2IREFOReference current output of DAC
3VRFIReference voltage input of DAC
4VGONot used (Connected to VDD with capacitor)
5XCPSIGONot used (Connected to ground)
6CPSIGOVideo composite/component (Y) signal output
7CSIGOVideo chroma (C) signal output
8V_AVDS2—Power supply (+2.5V)
9V_AVS—Ground
10IVD1—Power supply (+3.3V)
11I2C_CLKI/ONot used (open)
12I2C_DATAI/ONot used (open)
13GPIO0ISerial data input from M30620
14GPIO1OSerial data output to M30620
15GPIO2ISerial clock input from M30620
16GPIO3IData request signal input
17LVD1—Power supply (+2.5V)
18GPIO4OOk signal output
19GPIO5IChip select signal input from M30620
20GPIO6INot used (open)
21GPIO7ONot used (open)
22LVS1—Ground
23GPIO8ONot used (open)
24GPIO9OClock select signal output
25GPIO10ONot used (open)
26GPIO11OLatch signal output to PCM1748
27LVD2—Power supply (+2.5V)
28GPIO12OData load signal output to BU2507FV
29GPIO13OSerial data output
30GPIO14OSerial data clock output
31IVS1—Ground
32LVS2—Ground
33IVD2—Power supply (+3.3V)
59 to 66GRDAT8 to 15I/OData and address input/output to memory
67IVS4—Ground
68DRCASOCAS signal output to memory
69LVD4—Power supply (+2.5V)
70DRCKOClock output to memory
71IVD5—Power supply (+3.3V)
72DRRASORAS signal output
73DRWELOWrite enable signal output to memory
56
Page 57
HCD-XGV6/XGV8/XGV10AV
Pin No.
74NVOELOOut enable signal output to memory
75LVS4—Ground
76DRBSOBank select address output to memory
77DRDQM0OLower byte mask of memory
78DRDQM1OUpper byte mask of memory
79IVS5—Ground
80NC—Not used (open)
81SYSRSTISystem reset signal input
82IRDININot used (Connected to ground)
83NC—Not used (open)
84VDD1—Power supply (+2.5V)
85V16MI/ONot used (open)
86DOUTODigital audio data output (Not used)
87L_CDLRCKID/A interface, L/R clock input
88LRCKOD/A interface, L/R clock output
89VSS1—Ground
90L_CDDAT AISerial data input from D/A interface
91PCMDOSerial data output to D/A interface
92L_CDBCKIBit clock input (2’s COMP) from D/A interface
93BCKOBit clock output (2’s COMP) to D/A interface
94EMPHONot used (open)
95L_SQSOISubQ 80bit and PCM peak level data input
96SQSOOSubQ 80bit and PCM peak level data output
97VDD2—Power supply (+2.5V)
98L_SQCKOSQSO read out clock output
99SQCKISQSO read out clock input
100SBSOONot used (open)
101EXCKINot used (Connected to ground)
102DATAISerial data input from CPU
103L_DATAOSerial data output to CPU
104VSS2—Ground
105L_CDXRSTISystem reset signal input (L:reset)
106XRSTOSystem reset signal output (L:reset)
107MUTEINot used (Connected to ground)
108L_XLATOLatch signal output to CPU
109XLATILatch signal input from CPU
110L_DCLKOSerial data clock output
111CLOKISerial data clock input
112L_SENSISENS signal input
113SENSOSENS signal output
114L_SCLKOSENS serial data read clock output
115SCLKISENS serial data read clock input
116VDD3—Power supply (+2.5V)
117ATSKI/ONot used (Connected to ground)
118XUGFONot used (open)
119XPCKONot used (open)
120L_GFSIGPS signal input
121GFSOGPS signal output
122VSS3—Ground
I/O
DescriptionPin Name
57
Page 58
HCD-XGV6/XGV8/XGV10AV
Pin NamePin No.I/O
123L_CDC2POIC2PO signal input
124C2POOC2PO signal output
125L_SCORISub code sink (S0 or S1) detect signal input
126SCOROSub code sink (S0 or S1) detect signal output
127COUTI/ONot used (open)
128VDD4—Power supply (+2.5V)
129MIRRI/ONot used (open)
130DFCTI/ONot used (open)
131L_FOKI/OFocus OK signal input/output
132FOKI/OFocus OK signal input/output
133MDPOServo control signal output of spindle motor
134VSS4—Ground
135SSTOPIInner position of optical pick-up signal input
136FSTOONot used (open)
137SFDROSled motor control signal output
138SRDROSled motor control signal output
139VDD5—Power supply (+2.5V)
140TFDROTracking coil control signal output
141TRDROTracking coil control signal output
142FFDROFocus coil control signal output
143FRDROFocus coil control signal output
144VSS5—Ground
145WFCKONot used (open)
146WDCKONot used (open)
147ASYEINot used (Connected to VCC)
148VDD6—Power supply (+2.5V)
149XTAIICrystal oscillator input (33.8688MHz)
150XTAOOCrystal oscillator output (33.8688MHz)
151VSS6—Ground
152TES1INot used (Connected to ground)
153TESTINot used (Connected to ground)
154NC—Not used (open)
155NC—Not used (Connected to VDD with resistor))
156AVD0—Power supply (+2.5V)
157IGENIOP AMP current constant input
158AVS0—Ground
159ADIOONot used (open)
160RFDCIRF signal input
161CEIcenter servo analog signal input
162TEITracking error signal input
163SEISled error signal input
164FEIFocus error sigunal input
165VCICenter voltage signal input
166VPCOOEFM PLL charge pump output
167VCTLIEFM PLL charge pump input
168FILOOMaster PLL filter output
169FILIIMaster PLL filter input
170PCOOMaster PLL change pump output
171CLTVIVCO1 control signal input
Description
58
Page 59
HCD-XGV6/XGV8/XGV10AV
Pin No.
172AVS1—Ground
173RFACIEFM (RF) signal input
174BIASICurrent source input
175ASYIIComparator voltage input
176ASYOOEFM full swing signal output (L:VSS, H:VDD)
177AVD1—Power supply (+2.5V)
178VDD7—Power supply (+2.5V)
179SOUTONot used (open)
180SOCKONot used (open)
181XOLTONot used (open)
182C4MONot used (open)
183LOCKI/ONot used (open)
184VSS7—Ground
185MD2IDigital out control (L:OFF, H:ON)
186SCSYINot used (Connected to ground)
187PWMIINot used (Connected to ground)
188VDD8—Power supply (+2.5V)
189XTSLIX’tal frequency select input (L:16.9344MHz, H:33.8688MHz)
190VSS8—Ground
191PVS2—Ground
192LPFIIPLL2 filter terminal
193LPFOIPLL2 filter terminal
194PVD2—Power supply (+2.5V)
195NC—Not used (open)
196NC—Not used (open)
197PVD1—Power supply (+2.5V)
198PVS1—Ground
199TRODE0INot used (Connected to ground)
200AUDDTIINot used (Connected to ground)
201AUDDTO0OAudio serial data output to PCM1748
202AUDDTO1ODigital audio data output (Not used)
203AUDBCKOAudio serial data bit clock output to PCM1748
204AUDLRCKOAudio serial data L/R clock output to PCM1748
205AUDXCLKOOAudio serial clock output to PCM1748
206CLKAICrystal oscillator input (27MHz)
207CLKBOCrystal oscillator output (27MHz)
208VDD9—Power supply (+2.5V)
209THRCLKINot used (open)
210TESTENINot used (Connected to ground)
211TCLKINot used (Connected to ground)
212TMODE1INot used (Connected to ground)
213TRSTINot used (open)
214VSS9—Ground
215V_AVS1—Ground
216V_AVD1—Power supply (+2.5V)
Pin Name
I/O
Discription
59
Page 60
HCD-XGV6/XGV8/XGV10AV
• IC501 M30620MCN-A06FP SYSTEM CONTOL (MAIN Board)
Pin NamePin No.I/O
1AUDIO-OUTOMD output mute signal output
2STEREOIStereo signal input
3TUNEDITuned signal input
4SIRCSISIRCS input
5CD-MUTEOCD mute signal output
6–—Not used (open)
7–—Not used (open)
8BYTEINot used (connected to ground)
9CNVSS—Not used (Connected to ground with resistor)
10XC-INISub clock input
11XC-OUTOSub clock output
12RESETISystem reset input
13X-OUTOMain system clock output (16MHz)
14VSS—Ground
15X-INIMain system clock input (16MHz)
16VCC—Power supply (+5V)
17NMIINot used (Pull up with resistor)
18RDS-INTINot used (Connected to ground with resistor)
19SCOROChip select signal output to CXD1887R
20AC-CUTIAC cut check signal input
21ST-MUTEOTuner mute signal output
22ST-CEOTuner chip enable signal output
23ST-DOUTOTuner data output
24BU-PWM3OBU PWM 3 (for CD-RW) signal output (Not used)
25ST-DINITuner data input
26BU-PWM2OBU PWM 2 (for CD-RW) signal output (Not used)
27ST-CLKOTuner clock signal output
28BU-PWM1OBU PWM 1 (for CD-RW) signal output (Not used)
29IIC-CLKIIIC serial data clock input
30IIC-DATAIIIC serial data input
31–—Not used (open)
32SQ-DATAIOK signal input from CXD1887R
33SQ-CLKOVideo mute signal output to BD7600FV
34SENSINot used (open)
35CD-DATAOSerial data output to CXD1887R
36XLTISerial data input from CXD1887R
37CD-CLKOSerial clock output to CXD1887R
38CD-POWEROCD power on/off signal output
39CLK-OUTONot used (open)
40HOLDOLaser diode control signal output
41OTM-RESETOOther micom reset
42–—Not used (open)
43XRSTOReset signal output to AN41020A
44MTR-CTRL1OCD motor control 1 output
45MTR-CTRL2OCD motor control 2 output
46REC-AIRecord tab switch for SIDE-A signal input
47LED-DISCODISC LED on/off signal output
48BU UP/DW SWIBU up switch signal input
49TBL-SENSITable sensor signal input
50REC-BIRecord tab switch for SIDE-B signal input
Description
60
Page 61
HCD-XGV6/XGV8/XGV10AV
Pin No.
51A-TRGOTCM-A trigger output
52B-TRGOTCM-B Trigger output
53AMS-INIAMS signal input
54CAPM-H/LOCapstan motor high/low signal output
55CAPM-CTRLOCapstan motor REV/FWD/STOP control signal output
56A-PLAYITCM-A play switch input
57B-PLAYITCM-B play switch input
58TC-MUTEOTC line mute signal output
59REC/PB/PASSOVideo input select signal output (A)
60NR ON/OFFOVideo input select signal output (B)
61REC-MUTEOREC mute signal output
62VCC—Power supply (+3.3V)
63SOFT-TESTONot used (open)
64VSS—Ground
65BIASOBias on/off signal output
66EQ-H/NOEQ high/Normal signal output
67PB-A/BOTC A/B select signal output
68ALCOALC signal output
69TC-RELAYOTC relay control signal output
70A-HALFIA deck half detection signal input
71FUNC-SEL0OFunction select A signal output
72FUNC-SEL1OFunction select B signal output
73KEY-ECOIECO key signal input
74KEY-POWERIPower key signal input
75LED-STBYOStandby LED driver signal output
76VIDEO-MUTEOVideo mute signal output
77PL-LATOPrologic sound control LAT signal
78PL-DATOPrologic sound control data
79PL-CLKOPrologic sound control clock
80EQIC-DATOSerial data output to Audio EQIC
81EQIC-CLKOSerial data clock output to Audio EQIC
82LINE-MUTEOTA LINE mute signal output
83STK-MUTEOMute signal output to power IC
84STBY-RELAYOStandby relay driver signal output
85REAR-RELAYORear speaker relay driver signal output
86HP-MUTEOHeadphone mute signal output
87FRONT-RELAYOFront speaker relay driver signal output and woofer mute signal
88PROTECTISpeaker protection signal input
89A-SHUTITCM-A reel pulse input
90B-SHUTITCM-B reel pulse input
91B-HALFIB deck half detection input
92MODEL-INIModel input
93DEST-INIDestination input
94DBFB-H/LODBFB high/low signal output
95HP-INIHeadphone detect input
96AVSS—Ground
97SW-MODEOSuper woofer mode signal output
98VREFIReference voltage input
99AVCC—Power supply (+3.3V)
100RDS-DATAINot used (Connected to ground)
Pin Name
I/O
Discription
61
Page 62
HCD-XGV6/XGV8/XGV10AV
• IC601 MB90M407APF-G-120-BND DISPLAY CONTROL (PANEL FL Board)
Pin NamePin No.I/O
1 to 10GR-16 to GR-7OFLD grid output
11VSS-IO—Ground
12 to 17GR-6 to GR-1OFLD grid output
18 to 22SEG-1 to SEG-5OFLD segment output
23VDD-FIP—Power supply (+3.3V)
24 to 41SEG-6 to SEG-23OFLD segment output
42VSS-IO—Ground
43,44SEG-24, SEG-25OFLD segment output
45 to 47NO USEDONot used (open)
48VKK—Power supply (-35V)
49MD0INot used (pull up with resistor)
50MD1/VDD-VFTINot used (pull up with resistor)
51MD2INot used (pull down with resistor)
52D-SWICD lid open/close detect signal input
53DISTOGuitar distortion ON/OFF signal output
54SOFT TESTONot used (open)
55LED SELBOLED group B select signal output
56VOL AIVolume encoder signal A input
57VOL BIVolume encoder signal B input
58JOG AIAMS jog dial encoder signal A input
59JOG BIAMS jog dial encoder signal B input
60I2C-DATAOIIC serial data output
61I2C-CLOCKOIIC clock signal output
62AVCC—Power supply (+3.3V)
63AVSS—Ground
64 to 69KEY0 to KEY5IKey input (A/D port)
70BPF1-F02ISpectrum analyzer BPF signal input
71BPF2-F03ISpectrum analyzer BPF signal input
72BPF3-F04ISpectrum analyzer BPF signal input
73BPF4-F05ISpectrum analyzer BPF signal input
74BPF5-F06ISpectrum analyzer BPF signal input
75ALL BANDIL+R signal input
76LED-SCKOSerial clock output to LED driver
77RESETIReset input
78LED-DATOSerial data output to LED driver
79LED-LATCHOLatch signal output to LED driver
80LED-SELAOLED group A select signal output
81VSS-CPU—Ground
82XOUTOCrystal oscillator output (4MHz)
83XINICrystal oscillator input (4MHz)
84VCC-CPU—Power supply (+3.3V)
85 to 100 NO USEDONot used (open)
Description
62
Page 63
7-34. IC BLOCK DIAGRAMS
IC103 CXA2581N-T4 (BD BOARD)
AC
SUM
APC
EQ_IN
AC_SUM
GND
1LD
2
PD
3
4
5
6
A
7
B
8
C
9
D
RW/ROM
VOFST
VC
RW/ROM
VOFST
B
C
A
D
HCD-XGV6/XGV8/XGV10AV
30
DC_OFST
RW/ROM
RFDCI
DVCC
VC
RW/ROM
VC
VCC
EQ
ON/OFF
VC
DVC
VCC
EQ
AC
VCA
VCC
29
RFDCO
28
VC
27
VC
26
RFC
25
VFC
24
BST
23
RFG
VCC
22
21
CEI
CE
20
TE_BAL
19
DVCC
DVC
RFAC
SW
RW/ROM
DVC
DVCC
DVCC
TE
18
FEI
17
FE
16
10
F
11
E
12
13
14
15
gm
gm
APC-OFF(Hi-Z)
RW/ROM
(H/L)
DVC
AVC
DVC
RW/ROM
VOFST
VC
DVC
63
Page 64
HCD-XGV6/XGV8/XGV10AV
IC102 AN41020A (BD BOARD)
VO3+
VO3-
PGND2
PGND2
VO4+
STBY
VO4-
PVCC2
PVCC2
NC(BC4)
NC(BC3)
NC(VPUMP2)
NC(CT)
NC(SW)
NC(FB)
VREF
IN4
IN4R
OPO3(NC)
IN3-
IN3+
SVCC
PVCC/2
NC
NC
NC
NC
NC
NC
RESET CIRCUIT
DIRECTION DET
DIRECTION DET
DIRECTION DET
DIRECTION DET
PVCC/2
VO2-
VO2+
PGND1
PGND1
VO1-
NC
NC
PVCC/2(NC)
NC
VO1+
NC
PVCC1
PVCC1
NC(BC2)
NC
NC(BC1)
NC(VPUMP1)
NC(VDD)
OP+
OP-
OP.O
IN1+
IN1-
OPO1(NC)
IN2+
IN2-
OPO2(NC)
SGND
64
Page 65
HCD-XGV6/XGV8/XGV10AV
IC321 µPC1330HA (MAIN BOARD (3/3))
INVERTER
COMPARATER
2
1
SW R1 GNDSW P1
3
56789
4
CONT GNDVCCSW P2 GND
IC201 TA8409S (MOTOR BOARD)
STANDBY
BLOCK
SW R2
IC191 BA7615N (MAIN BOARD (1/3))
VREF
BLOCK
MUTE
1
2
4
3
B
A
IN1
IN2
6db
LOGIC
6
8
7
5
C
IN3
VCC
IN4
75Ω
10
9
GND
VOUT
HEAT
CUT OFF
BLOCK
23
1
VCCOUT2NCGND
IN2
IC602 BA3830F (PANEL FL BOARD)
REFERENCE
1
R02
R01
LINE NF
LINE IN
REC NF
REC IN
RST.C
BIAS
GND
2
3
4
5
6
7
8
9
CURRENT
REFERENCE
CURRENT
–
+
–
+
BAND
PASS
FILTER
DET
RESET
56
4
7
VS
OUT1VREFIN1
8
9
IC851 M65850P (MIC/GUITAR BOARD)
RST
18
17
16
15
14
13
12
11
10
F01
F02
F03
F04
F05
F06
REC LEVEL
VCC
1
LPF1IN
VCC
1/2 VCC
AUTO
RESET
LPF1
CLOCK
REF
OSCILLATOR
CLOCK
MAIN
RESET
CONTROL
D1
DO0
A/D
234567
OP1IN
OP1OUT
LPF1OUT
DO1
CC1
OP2IN
D/A
MO
MI
OP2OUT
LPF2IN
20KBIT
CC2
LPF2OUT
89101413 1211
LPF2
SRAM
GND
65
Page 66
HCD-XGV6/XGV8/XGV10AV
IC301 BA7046F-F2 (VIDEO BOARD)
ROSC
HD OUT
SYNC OUT
VD OUT
1
H.OSC
2
3
4
V.SEPA
PHASE
COMP
SYNC
SEPA
IC304 NJM2209M (TE2) (VIDEO BOARD)
N.C
14
13
GND
8
7
6
5
P.CP
VCC
VIDEO IN
GND
PHASE
12
DELAY
IC303 NJM2255M (TE2) (VIDEO BOARD)
TINT
8
HUE ADJUST
123
V IN
N.C
11
VIDEO
10
INPUT
N.C
FREQUENCY
CHARACTERISTIC
COMPENSATION
9
8
GND
7
SATURATION
+Ø
(COLOR BURST)
SATURATION
–X
(COLOR BURST)
COLOR OFFSET
ADJUST
ADJUST
V OUT
6
COLOR
BGP
5
4
V+
LOWER
LIMITER
123
VIDEO
N.C
OUTPUT
LPF
(2)
DIFFERENTIATION
INPUT
SECONDARY
DIFFERENTIATION
SWITCH
CONTROL
4
V+
IC504 PCM1748E/2K (VIDEO BOARD)
BCK
1
Serial
Input
2
DATA
LRCK
DGND
VDD
VCC
3
4
5
6
I/F
Power
Supply
8x Oversampling Digital Filter
with Function Controller
Enhanced Multi-Level
Deita-Sigma Modurator
GAIN ADJ
5
CONTROL
System Clock
DACDAC
LOWER
LIMITER
(1)
6
N.C
CLAMP
SYNC
CHIP
7
OUTPUT
DIFFERENTIATION
System Clock
Manager
Function
Control
I/F
Zero Detect
16
MCLK
LAT
15
14
CLK
13
DATA
DZFL
12
11
DZFR
66
LOUT
ROUT
7
8
Output Amp and
Low-Pass Filter
Output Amp and
Low-Pass Filter
VCOM
10
AGND
9
Page 67
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
• The mechanical parts with no reference number
in the exploded views are not supplied.
8-1. CASE, BACK PANEL SECTION
SECTION 8
EXPLODED VIEWS
• Hardware (# mark) list and accessories are
given in the last of this parts list.
• Abbreviation
SP: Singapore model
TH: Thai model
EA: Saudi Arabia model
HCD-XGV6/XGV8/XGV10AV
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
(Please bend like original parts)
1524-235-701-01 DUST COVER
153A-4727-618-A PA BOARD, COMPLETE (XGV6)
153A-4727-660-A PA BOARD, COMPLETE (XGV8)
153A-4728-672-A PA BOARD, COMPLETE (XGV10AV)
0 T9511-433-606-11 TRANSFORMER, POWER (XGV6)
0 T9511-435-249-11 TRANSFORMER, POWER (XGV10AV:SP,TH)
0 T9511-437-593-11 TRANSFORMER, POWER (XGV8)
0 T9511-437-829-11 TRANSFORMER, POWER (XGV10AV:EA)
#1
#1
163A-4728-373-A VIDEO BOARD, COMPLETE
1641-773-137-11 WIRE (FLAT TYPE) (19 CORE)
#17-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#27-685-872-09 SCREW +BVTT 3X8 (S)
#47-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#57-685-881-09 SCREW +BVTT 4X8 (S)
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
• Abbreviation
SP: Singapore model
TH: Thai model
EA: Saudi Arabia model
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board
name.
R1041-216-835-11 METAL CHIP15K5%1/16W
R1051-216-821-11 METAL CHIP1K5%1/16W
R1091-216-846-11 METAL CHIP120K5%1/16W
R1111-216-846-11 METAL CHIP120K5%1/16W
R1121-216-864-11 METAL CHIP05%1/16W
R1131-216-826-11 METAL CHIP2.7K5%1/16W
R1141-216-841-11 METAL CHIP47K5%1/16W
R1171-216-841-11 METAL CHIP47K5%1/16W
R1181-216-864-11 METAL CHIP05%1/16W
R1201-216-846-11 METAL CHIP120K5%1/16W
R1221-216-845-11 METAL CHIP100K5%1/16W
R1231-216-797-11 METAL CHIP105%1/16W
R1241-216-797-11 METAL CHIP105%1/16W
R1251-216-839-11 METAL CHIP33K5%1/16W
R1261-216-839-11 METAL CHIP33K5%1/16W
R1511-216-845-11 METAL CHIP100K5%1/16W
R1521-216-829-11 METAL CHIP4.7K5%1/16W
R1761-216-864-11 METAL CHIP05%1/16W
R1791-216-833-11 METAL CHIP10K5%1/16W
R2261-216-821-11 METAL CHIP1K5%1/16W
R2271-216-845-11 METAL CHIP100K5%1/16W
R2281-216-853-11 METAL CHIP470K5%1/16W
R2291-216-825-11 METAL CHIP2.2K5%1/16W
R2311-216-821-11 METAL CHIP1K5%1/16W
R2341-216-864-11 METAL CHIP05%1/16W
R2351-216-821-11 METAL CHIP1K5%1/16W
R2361-216-821-11 METAL CHIP1K5%1/16W
R7711-249-419-11 CARBON1.5K5%1/4W F
R7721-249-419-11 CARBON1.5K5%1/4W F
R7731-249-421-11 CARBON2.2K5%1/4W F
R7741-247-843-11 CARBON3.3K5%1/4W
R7751-249-425-11 CARBON4.7K5%1/4W F
A-4728-595-A MAIN BOARD, COMPLETE (XGV8)
A-4729-487-A MAIN BOARD, COMPLETE (XGV6)
A-4676-308-A MAIN BOARD, COMPLETE (XGV10AV:SP,TH)
A-4729-341-A MAIN BOARD, COMPLETE (XGV10AV:EA)
JR414 1-216-295-91 SHORT CHIP0
JR723 1-216-295-91 SHORT CHIP0
< COIL >
< IC >
IC111 6-702-422-11 IC M61519FPD61G
IC181 8-759-009-06 IC MC14052BFEL
IC191 8-759-571-53 IC BA7615N
IC301 6-702-130-01 IC HA12237F
IC321 8-759-143-54 IC uPC1330HA
IC341 8-759-100-96 IC NJM4558M-TE2
IC501 6-801-543-01 IC M30620MCN-A06FP
IC601 8-759-100-96 IC NJM4558M-TE2
IC801 8-759-532-64 IC M62703SL-TP
IC911 8-759-701-59 IC TA7809S
IC921 8-759-039-69 IC uPC7805AHF
IC922 6-701-760-01 IC uPC3504AHF
IC931 8-759-604-32 IC M5F7810L
IC961 8-759-088-08 IC uPC7812AHF (XGV10AV,XGV6)
JR71-216-295-91 SHORT CHIP0
JR121-216-295-91 SHORT CHIP0
JR131-216-296-11 SHORT CHIP0
JR141-216-296-11 SHORT CHIP0
JR151-216-295-91 SHORT CHIP0
JR161-216-295-91 SHORT CHIP0
JR171-216-295-91 SHORT CHIP0
JR201-216-295-91 SHORT CHIP0
JR211-216-295-91 SHORT CHIP0
JR221-216-295-91 SHORT CHIP0
JR231-216-295-91 SHORT CHIP0
JR241-216-295-91 SHORT CHIP0
JR251-216-295-91 SHORT CHIP0
JR261-216-295-91 SHORT CHIP0
JR271-216-295-91 SHORT CHIP0
JR291-216-295-91 SHORT CHIP0
JR301-216-296-11 SHORT CHIP0
JR311-216-295-91 SHORT CHIP0
JR321-216-295-91 SHORT CHIP0
JR181 1-216-295-91 SHORT CHIP0 (XGV6,XGV8)
JR182 1-216-295-91 SHORT CHIP0 (XGV6,XGV8)
JR192 1-216-295-91 SHORT CHIP0 (XGV6,XGV8)
JR301 1-216-295-91 SHORT CHIP0
JR303 1-216-295-91 SHORT CHIP0
JR351 1-216-295-91 SHORT CHIP0
JR353 1-216-295-91 SHORT CHIP0
JR402 1-216-295-91 SHORT CHIP0
R1111-216-825-11 METAL CHIP2.2K5%1/16W
R1121-216-833-11 METAL CHIP10K5%1/16W
R1131-216-857-11 METAL CHIP1M5%1/16W
R1151-216-841-11 METAL CHIP47K5%1/16W
R1161-216-841-11 METAL CHIP47K5%1/16W
R1171-216-849-11 METAL CHIP220K5%1/16W
R1181-216-849-11 METAL CHIP220K5%1/16W
R1191-216-819-11 METAL CHIP6805%1/16W
R1211-216-855-11 METAL CHIP680K5%1/16W
R1221-216-825-11 METAL CHIP2.2K5%1/16W
R1241-216-833-11 METAL CHIP10K5%1/16W
R1251-216-833-11 METAL CHIP10K5%1/16W
R1261-216-833-11 METAL CHIP10K5%1/16W
R1271-216-849-11 METAL CHIP220K5%1/16W
R1281-216-849-11 METAL CHIP220K5%1/16W
R1291-216-857-11 METAL CHIP1M5%1/16W
R1301-216-857-11 METAL CHIP1M5%1/16W
R1321-216-839-11 METAL CHIP33K5%1/16W
R1331-216-829-11 METAL CHIP4.7K5%1/16W
R1341-216-857-11 METAL CHIP1M5%1/16W
R1351-216-295-91 SHORT CHIP0
R1361-216-295-91 SHORT CHIP0
R1611-216-825-11 METAL CHIP2.2K5%1/16W
R1621-216-833-11 METAL CHIP10K5%1/16W
R1631-216-857-11 METAL CHIP1M5%1/16W
R1651-216-841-11 METAL CHIP47K5%1/16W
R1661-216-841-11 METAL CHIP47K5%1/16W
R1671-216-849-11 METAL CHIP220K5%1/16W
R1681-216-849-11 METAL CHIP220K5%1/16W
R1691-216-819-11 METAL CHIP6805%1/16W
R1711-216-855-11 METAL CHIP680K5%1/16W
R1721-216-825-11 METAL CHIP2.2K5%1/16W
R1741-216-833-11 METAL CHIP10K5%1/16W
R1761-216-837-11 METAL CHIP22K5%1/16W
R1791-216-833-11 METAL CHIP10K5%1/16W
R1801-216-833-11 METAL CHIP10K5%1/16W
R1811-216-833-11 METAL CHIP10K5%1/16W
R1821-216-833-11 METAL CHIP10K5%1/16W
R3011-216-827-11 METAL CHIP3.3K5%1/16W
R3021-216-829-11 METAL CHIP4.7K5%1/16W
R3041-216-825-11 METAL CHIP2.2K5%1/16W
R3051-216-841-11 METAL CHIP47K5%1/16W
R3081-216-837-11 METAL CHIP22K5%1/16W
R3091-216-857-11 METAL CHIP1M5%1/16W
R3101-216-833-11 METAL CHIP10K5%1/16W
R3111-216-829-11 METAL CHIP4.7K5%1/16W
R3181-216-833-11 METAL CHIP10K5%1/16W
R3191-216-845-11 METAL CHIP100K5%1/16W
R3201-216-825-11 METAL CHIP2.2K5%1/16W
R3211-216-829-11 METAL CHIP4.7K5%1/16W
R3241-216-825-11 METAL CHIP2.2K5%1/16W
R3251-216-825-11 METAL CHIP2.2K5%1/16W
R3261-216-833-11 METAL CHIP10K5%1/16W
R3271-216-833-11 METAL CHIP10K5%1/16W
R3281-216-834-11 METAL CHIP12K5%1/16W
R3291-216-834-11 METAL CHIP12K5%1/16W
R3301-216-837-11 METAL CHIP22K5%1/16W
R3341-216-836-11 METAL CHIP18K5%1/16W
R3351-216-837-11 METAL CHIP22K5%1/16W
R3361-216-821-11 METAL CHIP1K5%1/16W
R3371-216-837-11 METAL CHIP22K5%1/16W
R3381-216-837-11 METAL CHIP22K5%1/16W
R3391-216-833-11 METAL CHIP10K5%1/16W
R3401-216-833-11 METAL CHIP10K5%1/16W
R3411-216-821-11 METAL CHIP1K5%1/16W
R3421-216-821-11 METAL CHIP1K5%1/16W
R3431-216-861-11 METAL CHIP2.2M5%1/16W
R3441-216-833-11 METAL CHIP10K5%1/16W
R3451-216-833-11 METAL CHIP10K5%1/16W
R3461-216-833-11 METAL CHIP10K5%1/16W
R3471-216-833-11 METAL CHIP10K5%1/16W
R3481-216-833-11 METAL CHIP10K5%1/16W
R3491-216-829-11 METAL CHIP4.7K5%1/16W
R3501-216-833-11 METAL CHIP10K5%1/16W
R3511-216-827-11 METAL CHIP3.3K5%1/16W
R3521-216-829-11 METAL CHIP4.7K5%1/16W
R3541-216-825-11 METAL CHIP2.2K5%1/16W
R3551-216-841-11 METAL CHIP47K5%1/16W
R3581-216-833-11 METAL CHIP10K5%1/16W
R3711-216-833-11 METAL CHIP10K5%1/16W
R3721-216-833-11 METAL CHIP10K5%1/16W
R3741-216-833-11 METAL CHIP10K5%1/16W
R3751-216-833-11 METAL CHIP10K5%1/16W
R3771-216-833-11 METAL CHIP10K5%1/16W
R3781-216-833-11 METAL CHIP10K5%1/16W
R3811-216-819-11 METAL CHIP6805%1/16W
R3821-216-825-11 METAL CHIP2.2K5%1/16W
R3831-216-825-11 METAL CHIP2.2K5%1/16W
R3841-216-819-11 METAL CHIP6805%1/16W
R3851-216-825-11 METAL CHIP2.2K5%1/16W
R3861-216-825-11 METAL CHIP2.2K5%1/16W
R3871-216-841-11 METAL CHIP47K5%1/16W
R3881-216-827-11 METAL CHIP3.3K5%1/16W
R3891-216-827-11 METAL CHIP3.3K5%1/16W
R3901-216-827-11 METAL CHIP3.3K5%1/16W
R3911-216-827-11 METAL CHIP3.3K5%1/16W
R3921-216-827-11 METAL CHIP3.3K5%1/16W
R3931-216-833-11 METAL CHIP10K5%1/16W
R3941-216-849-11 METAL CHIP220K5%1/16W
R4011-216-829-11 METAL CHIP4.7K5%1/16W
R4021-216-833-11 METAL CHIP10K5%1/16W
R4031-216-829-11 METAL CHIP4.7K5%1/16W
R4041-216-833-11 METAL CHIP10K5%1/16W
R4051-216-833-11 METAL CHIP10K5%1/16W
R4061-216-833-11 METAL CHIP10K5%1/16W
R4071-216-295-91 SHORT CHIP0
R4081-216-295-91 SHORT CHIP0
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
R4101-216-295-91 SHORT CHIP0
R4121-216-835-11 METAL CHIP15K5%1/16W
R4131-216-833-11 METAL CHIP10K5%1/16W
R4141-216-833-11 METAL CHIP10K5%1/16W
R4311-216-845-11 METAL CHIP100K5%1/16W
R5921-216-815-11 METAL CHIP3305%1/16W
(XGV10AV)
R5931-216-829-11 METAL CHIP4.7K5%1/16W
R5941-216-829-11 METAL CHIP4.7K5%1/16W
R5951-216-809-11 METAL CHIP1005%1/16W
R5011-216-833-11 METAL CHIP10K5%1/16W
R5021-216-809-11 METAL CHIP1005%1/16W
R5031-216-809-11 METAL CHIP1005%1/16W
R5041-216-809-11 METAL CHIP1005%1/16W
R5051-216-833-11 METAL CHIP10K5%1/16W
R5091-216-833-11 METAL CHIP10K5%1/16W
R5111-216-851-11 METAL CHIP330K5%1/16W
R5131-216-295-91 SHORT CHIP0
R5161-216-833-11 METAL CHIP10K5%1/16W
R5171-216-833-11 METAL CHIP10K5%1/16W
R5191-216-809-11 METAL CHIP1005%1/16W
R5211-216-809-11 METAL CHIP1005%1/16W
R5221-216-809-11 METAL CHIP1005%1/16W
R5231-216-809-11 METAL CHIP1005%1/16W
R5251-216-809-11 METAL CHIP1005%1/16W
R5271-216-809-11 METAL CHIP1005%1/16W
R5291-216-809-11 METAL CHIP1005%1/16W
R5301-216-809-11 METAL CHIP1005%1/16W
R5311-216-833-11 METAL CHIP10K5%1/16W
R5321-216-809-11 METAL CHIP1005%1/16W
R5331-216-809-11 METAL CHIP1005%1/16W
R5341-216-809-11 METAL CHIP1005%1/16W
R5351-216-809-11 METAL CHIP1005%1/16W
R5361-216-809-11 METAL CHIP1005%1/16W
R5371-216-809-11 METAL CHIP1005%1/16W
R5401-216-841-11 METAL CHIP47K5%1/16W
R5411-216-809-11 METAL CHIP1005%1/16W
R5431-216-809-11 METAL CHIP1005%1/16W
R5471-216-809-11 METAL CHIP1005%1/16W
R5481-216-809-11 METAL CHIP1005%1/16W
R5491-216-833-11 METAL CHIP10K5%1/16W
R5561-216-809-11 METAL CHIP1005%1/16W
R5571-216-809-11 METAL CHIP1005%1/16W
R5701-216-809-11 METAL CHIP1005%1/16W
R5711-216-835-11 METAL CHIP15K5%1/16W
R5721-216-835-11 METAL CHIP15K5%1/16W
R5731-216-809-11 METAL CHIP1005%1/16W
R5741-216-809-11 METAL CHIP1005%1/16W
R5751-216-809-11 METAL CHIP1005%1/16W
R5771-216-809-11 METAL CHIP1005%1/16W
R5781-216-809-11 METAL CHIP1005%1/16W
R5791-216-809-11 METAL CHIP1005%1/16W
R5801-216-809-11 METAL CHIP1005%1/16W
R5811-216-809-11 METAL CHIP1005%1/16W
R5821-216-833-11 METAL CHIP10K5%1/16W
R5831-216-809-11 METAL CHIP1005%1/16W
R5841-216-809-11 METAL CHIP1005%1/16W
R5851-216-809-11 METAL CHIP1005%1/16W
R5861-216-809-11 METAL CHIP1005%1/16W
R5871-216-809-11 METAL CHIP1005%1/16W
R5881-216-809-11 METAL CHIP1005%1/16W
R5891-216-809-11 METAL CHIP1005%1/16W
R5901-216-809-11 METAL CHIP1005%1/16W
R5911-216-809-11 METAL CHIP1005%1/16W
R5921-216-295-91 SHORT CHIP0 (XGV6)
R5921-216-811-11 METAL CHIP1505%1/16W
(XGV8)
R5961-216-295-91 SHORT CHIP0 (EXCEPT XGV10AV:EA)
R5961-216-821-11 METAL CHIP1K5%1/16W
(XGV10AV:EA)
R5971-216-841-11 METAL CHIP47K5%1/16W
R5981-216-841-11 METAL CHIP47K5%1/16W
R5991-216-833-11 METAL CHIP10K5%1/16W
R6011-216-821-11 METAL CHIP1K5%1/16W
R6021-216-821-11 METAL CHIP1K5%1/16W
R6031-216-841-11 METAL CHIP47K5%1/16W
R6041-216-821-11 METAL CHIP1K5%1/16W
R6051-216-854-11 METAL CHIP560K5%1/16W
R6061-216-841-11 METAL CHIP47K5%1/16W
R6071-216-821-11 METAL CHIP1K5%1/16W
R6081-216-845-11 METAL CHIP100K5%1/16W
R6091-216-033-00 METAL CHIP2205%1/10W
R6111-216-821-11 METAL CHIP1K5%1/16W
R6121-216-821-11 METAL CHIP1K5%1/16W
R6131-216-815-11 METAL CHIP3305%1/16W
R6141-216-821-11 METAL CHIP1K5%1/16W
R6511-216-821-11 METAL CHIP1K5%1/16W
R6521-216-821-11 METAL CHIP1K5%1/16W
R6531-216-841-11 METAL CHIP47K5%1/16W
R6541-216-821-11 METAL CHIP1K5%1/16W
R6551-216-854-11 METAL CHIP560K5%1/16W
R6561-216-841-11 METAL CHIP47K5%1/16W
R6571-216-821-11 METAL CHIP1K5%1/16W
R6581-216-845-11 METAL CHIP100K5%1/16W
R7011-216-821-11 METAL CHIP1K5%1/16W
R7021-216-845-11 METAL CHIP100K5%1/16W
R7031-216-821-11 METAL CHIP1K5%1/16W
R7041-216-845-11 METAL CHIP100K5%1/16W
R7051-216-833-11 METAL CHIP10K5%1/16W
R7061-216-825-11 METAL CHIP2.2K5%1/16W
R7071-216-857-11 METAL CHIP1M5%1/16W
R7111-216-832-11 METAL CHIP8.2K5%1/16W
(XGV10AV)
R7121-216-833-11 METAL CHIP10K5%1/16W
(XGV10AV)
R7131-218-866-11 METAL CHIP6.2K0.5%1/10W
(XGV10AV)
R7141-216-833-11 METAL CHIP10K5%1/16W
(XGV10AV)
R7151-218-866-11 METAL CHIP6.2K0.5%1/10W
(XGV10AV)
R7161-216-833-11 METAL CHIP10K5%1/16W
(XGV10AV)
R7211-218-285-11 RES-CHIP755%1/10W
R7221-216-804-11 METAL CHIP395%1/16W
R7231-211-990-11 METAL CHIP750.5%1/10W
(XGV10AV)
R7241-216-833-11 METAL CHIP10K5%1/16W
R7311-216-833-11 METAL CHIP10K5%1/16W
R7511-216-821-11 METAL CHIP1K5%1/16W
R7521-216-845-11 METAL CHIP100K5%1/16W
R7531-216-821-11 METAL CHIP1K5%1/16W
R7541-216-845-11 METAL CHIP100K5%1/16W
R7551-216-833-11 METAL CHIP10K5%1/16W
R7561-216-825-11 METAL CHIP2.2K5%1/16W
R7571-216-857-11 METAL CHIP1M5%1/16W
R7611-216-832-11 METAL CHIP8.2K5%1/16W
R8011-216-033-00 METAL CHIP2205%1/10W
R8021-216-829-11 METAL CHIP4.7K5%1/16W
R8031-216-829-11 METAL CHIP4.7K5%1/16W
R8041-216-841-11 METAL CHIP47K5%1/16W
R8051-216-841-11 METAL CHIP47K5%1/16W
R8061-216-833-11 METAL CHIP10K5%1/16W
R8071-216-821-11 METAL CHIP1K5%1/16W
R8081-216-845-11 METAL CHIP100K5%1/16W
R8091-216-845-11 METAL CHIP100K5%1/16W
(XGV10AV)
R8101-216-845-11 METAL CHIP100K5%1/16W
R8111-216-833-11 METAL CHIP10K5%1/16W
(XGV10AV)
R8121-216-827-11 METAL CHIP3.3K5%1/16W
R8131-216-833-11 METAL CHIP10K5%1/16W
R8141-216-837-11 METAL CHIP22K5%1/16W
R8151-216-837-11 METAL CHIP22K5%1/16W
R8161-216-845-11 METAL CHIP100K5%1/16W
R9211-216-825-11 METAL CHIP2.2K5%1/16W
R9221-216-815-11 METAL CHIP3305%1/16W
R9231-216-815-11 METAL CHIP3305%1/16W
R9241-216-815-11 METAL CHIP3305%1/16W
0 R9251-215-886-11 METAL OXIDE1005%2W
R9611-216-829-11 METAL CHIP4.7K5%1/16W
R9621-216-836-11 METAL CHIP18K5%1/16W
R9631-216-825-11 METAL CHIP2.2K5%1/16W
R6211-249-413-11 CARBON4705%1/4W F
R6221-249-415-11 CARBON6805%1/4W F
R6231-249-421-11 CARBON2.2K5%1/4W F
R6241-249-419-11 CARBON1.5K5%1/4W F
R6251-249-419-11 CARBON1.5K5%1/4W F
R6261-249-417-11 CARBON1K5%1/4W F
R6271-249-415-11 CARBON6805%1/4W F
R6281-249-413-11 CARBON4705%1/4W F
R6291-249-413-11 CARBON4705%1/4W F
R6301-249-415-11 CARBON6805%1/4W F
R6311-249-417-11 CARBON1K5%1/4W F
R6321-249-419-11 CARBON1.5K5%1/4W F
R6331-249-419-11 CARBON1.5K5%1/4W F
R6341-249-421-11 CARBON2.2K5%1/4W F
R6351-249-413-11 CARBON4705%1/4W F
R6361-249-415-11 CARBON6805%1/4W F
R6371-249-413-11 CARBON4705%1/4W F
R6381-249-415-11 CARBON6805%1/4W F
R6391-249-417-11 CARBON1K5%1/4W F
R6401-249-419-11 CARBON1.5K5%1/4W F
R6411-249-419-11 CARBON1.5K5%1/4W F
R6421-249-421-11 CARBON2.2K5%1/4W F
R6431-249-401-11 CARBON475%1/4W F
R6441-247-891-00 CARBON330K5%1/4W
R6451-247-891-00 CARBON330K5%1/4W
R6851-249-417-11 CARBON1K5%1/4W F
R6861-249-437-11 CARBON47K5%1/4W
R6881-249-437-11 CARBON47K5%1/4W
R6891-249-417-11 CARBON1K5%1/4W F
R6901-249-417-11 CARBON1K5%1/4W F
R6911-249-413-11 CARBON4705%1/4W F
R6921-249-413-11 CARBON4705%1/4W F
R6931-249-429-11 CARBON10K5%1/4W
R6941-249-429-11 CARBON10K5%1/4W
R6951-247-807-31 CARBON1005%1/4W
R6961-247-807-31 CARBON1005%1/4W
R6971-247-807-31 CARBON1005%1/4W
R6981-249-415-11 CARBON6805%1/4W F
R6991-249-411-11 CARBON3305%1/4W
R7001-249-413-11 CARBON4705%1/4W F
D7238-719-058-04 DIODE SEL5223S-TP15 (KEY CONTROL #)
< IC >
R7211-249-419-11 CARBON1.5K5%1/4W F
R7221-249-421-11 CARBON2.2K5%1/4W F
R7231-247-843-11 CARBON3.3K5%1/4W
R7241-249-425-11 CARBON4.7K5%1/4W F
R7251-249-427-11 CARBON6.8K5%1/4W F
R7061-249-417-11 CARBON1K5%1/4W F
R7071-249-417-11 CARBON1K5%1/4W F
R7081-249-419-11 CARBON1.5K5%1/4W F
R7091-249-419-11 CARBON1.5K5%1/4W F
R7101-249-421-11 CARBON2.2K5%1/4W F
R7111-247-843-11 CARBON3.3K5%1/4W
R7121-249-425-11 CARBON4.7K5%1/4W F
R7131-249-427-11 CARBON6.8K5%1/4W F
R7141-249-429-11 CARBON10K5%1/4W
R7151-249-431-11 CARBON15K5%1/4W
R2011-216-809-11 METAL CHIP1005%1/16W
R2021-216-809-11 METAL CHIP1005%1/16W
R2031-216-817-11 METAL CHIP4705%1/16W
R2041-216-851-11 METAL CHIP330K5%1/16W
R2051-216-841-11 METAL CHIP47K5%1/16W
R2061-216-847-11 METAL CHIP150K5%1/16W
R2071-218-892-11 METAL CHIP75K0.5%1/10W
R2081-216-841-11 METAL CHIP47K5%1/16W
R2091-216-847-11 METAL CHIP150K5%1/16W
R2101-218-892-11 METAL CHIP75K0.5%1/10W
R2111-216-845-11 METAL CHIP100K5%1/16W
R2121-216-845-11 METAL CHIP100K5%1/16W
R2161-216-833-11 METAL CHIP10K5%1/16W
R2171-216-833-11 METAL CHIP10K5%1/16W
R2711-216-825-11 METAL CHIP2.2K5%1/16W
R2721-216-845-11 METAL CHIP100K5%1/16W
R2731-216-833-11 METAL CHIP10K5%1/16W
R2811-216-825-11 METAL CHIP2.2K5%1/16W
R2821-216-845-11 METAL CHIP100K5%1/16W
R2831-216-833-11 METAL CHIP10K5%1/16W
R2911-216-825-11 METAL CHIP2.2K5%1/16W
R2921-216-845-11 METAL CHIP100K5%1/16W
R2931-216-833-11 METAL CHIP10K5%1/16W
R2941-216-821-11 METAL CHIP1K5%1/16W
IC102 8-759-701-40 IC NJM2100M(TE2)
IC201 6-700-399-01 IC uPC2925T-E1
IC202 8-759-460-72 IC BA033FP-E2
IC301 8-759-514-57 IC BA7046F-E2
IC302 8-759-530-30 IC TC74VHCU04FT(EL)
IC303 8-759-662-94 IC NJM2255M(TE2)
IC304 8-759-711-47 IC NJM2209M(TE2)
IC307 6-702-001-01 IC BD7600FV-E2
IC504 8-759-825-13 IC PCM1748E/2K
IC505 8-752-417-93 IC CXD1887R
IC506 6-702-000-01 IC BU2507FV-E2
IC507 6-702-572-01 IC M2V28S40ATP-6
IC508 6-802-318-01 IC MR27V401E-080MAZ060
< WIRE JUMPER >
JW203 1-216-864-11 METAL CHIP05%1/16W
JW301 1-216-864-11 METAL CHIP05%1/16W
JW523 1-216-864-11 METAL CHIP05%1/16W
JW524 1-216-864-11 METAL CHIP05%1/16W
R1021-216-809-11 METAL CHIP1005%1/16W
R1071-216-833-11 METAL CHIP10K5%1/16W
R1081-216-823-11 METAL CHIP1.5K5%1/16W
R1091-216-823-11 METAL CHIP1.5K5%1/16W
R1141-216-825-11 METAL CHIP2.2K5%1/16W
R1151-216-825-11 METAL CHIP2.2K5%1/16W
R1521-216-809-11 METAL CHIP1005%1/16W
R1571-216-833-11 METAL CHIP10K5%1/16W
R1581-216-823-11 METAL CHIP1.5K5%1/16W
R1591-216-823-11 METAL CHIP1.5K5%1/16W
R2021-216-809-11 METAL CHIP1005%1/16W
R3011-216-849-11 METAL CHIP220K5%1/16W
R3021-216-817-11 METAL CHIP4705%1/16W
R3031-216-846-11 METAL CHIP120K5%1/16W
R3051-216-833-11 METAL CHIP10K5%1/16W
R3061-216-821-11 METAL CHIP1K5%1/16W
R3071-216-833-11 METAL CHIP10K5%1/16W
R3081-216-833-11 METAL CHIP10K5%1/16W
R3091-216-833-11 METAL CHIP10K5%1/16W
R3101-216-821-11 METAL CHIP1K5%1/16W
R3111-216-813-11 METAL CHIP2205%1/16W
R3121-216-864-11 METAL CHIP05%1/16W
R3141-216-833-11 METAL CHIP10K5%1/16W
R3151-216-833-11 METAL CHIP10K5%1/16W
R3161-216-833-11 METAL CHIP10K5%1/16W
R3171-216-833-11 METAL CHIP10K5%1/16W
R3181-216-809-11 METAL CHIP1005%1/16W
R3211-216-813-11 METAL CHIP2205%1/16W
R3221-216-864-11 METAL CHIP05%1/16W
R5551-216-797-11 METAL CHIP105%1/16W
R5561-216-797-11 METAL CHIP105%1/16W
R5571-216-797-11 METAL CHIP105%1/16W
R5581-216-857-11 METAL CHIP1M5%1/16W
R5591-216-817-11 METAL CHIP4705%1/16W
R5611-216-821-11 METAL CHIP1K5%1/16W
R5811-216-809-11 METAL CHIP1005%1/16W
R5821-216-817-11 METAL CHIP4705%1/16W
R3231-216-817-11 METAL CHIP4705%1/16W
R3241-216-811-11 METAL CHIP1505%1/16W
R3251-216-826-11 METAL CHIP2.7K5%1/16W
R3261-216-825-11 METAL CHIP2.2K5%1/16W
R3271-216-809-11 METAL CHIP1005%1/16W
R3721-216-825-11 METAL CHIP2.2K5%1/16W
R3731-216-825-11 METAL CHIP2.2K5%1/16W
R3741-218-707-11 RES-CHIP4.3K5%1/10W
R3751-211-990-11 METAL CHIP750.5%1/10W
R3761-216-833-11 METAL CHIP10K5%1/16W
R5011-216-841-11 METAL CHIP47K5%1/16W
R5021-216-827-11 METAL CHIP3.3K5%1/16W
R5031-216-797-11 METAL CHIP105%1/16W
R5041-216-797-11 METAL CHIP105%1/16W
R5051-216-797-11 METAL CHIP105%1/16W
R5061-216-797-11 METAL CHIP105%1/16W
R5071-216-797-11 METAL CHIP105%1/16W
R5081-216-797-11 METAL CHIP105%1/16W
R5091-216-797-11 METAL CHIP105%1/16W
R5101-216-797-11 METAL CHIP105%1/16W
R5111-216-797-11 METAL CHIP105%1/16W
R5121-216-797-11 METAL CHIP105%1/16W
R5131-216-833-11 METAL CHIP10K5%1/16W
R5221-216-833-11 METAL CHIP10K5%1/16W
R5311-216-845-11 METAL CHIP100K5%1/16W
R5321-216-829-11 METAL CHIP4.7K5%1/16W
R5331-216-839-11 METAL CHIP33K5%1/16W
R5341-216-864-11 METAL CHIP05%1/16W
R5381-216-833-11 METAL CHIP10K5%1/16W
R5411-216-864-11 METAL CHIP05%1/16W
R5421-216-864-11 METAL CHIP05%1/16W
R5431-216-853-11 METAL CHIP470K5%1/16W
R5441-216-857-11 METAL CHIP1M5%1/16W
R5451-216-821-11 METAL CHIP1K5%1/16W
R5461-216-848-11 METAL CHIP180K5%1/16W
(T8.0AL 250V)(XGV8)
M201A-4660-977-A MOTOR ASSY
M9011-763-072-11 FAN, DC
0 T9511-433-606-11 TRANSFORMER, POWER (XGV6)
0 T9511-435-249-11 TRANSFORMER, POWER (XGV10AV:SP,TH)
0 T9511-437-593-11 TRANSFORMER, POWER (XGV8)
0 T9511-437-829-11 TRANSFORMER, POWER (XGV10AV:EA)
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
R5471-216-833-11 METAL CHIP10K5%1/16W
R5481-216-855-11 METAL CHIP680K5%1/16W
R5491-216-845-11 METAL CHIP100K5%1/16W
R5501-216-833-11 METAL CHIP10K5%1/16W
R5511-218-852-11 RES-CHIP1.6K5%1/10W
R5521-216-820-11 METAL CHIP8205%1/16W
R5541-216-797-11 METAL CHIP105%1/16W
92
Page 93
MEMO
HCD-XGV6/XGV8/XGV10AV
93
Page 94
HCD-XGV6/XGV8/XGV10AV
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.DateDescription of Revision
1.02002.07New
1.12002.12Change of the supply classification of the OP ASSY (Ref. No. 551).
(SPM-02117)
1.22004.09Correction of part No. (Ref. No. 151 and 164).(SPM-04094)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.