Sony HCD-XG100AV, HCD-XG900AV Service manual

HCD-XG100AV/XG900AV

SERVICE MANUAL

Ver 1.0 2001.04

HCD-XG100AV/XG900AV are the amplifier, CD player, tape deck and tuner section in LBT-XG100AV/XG900AV.

This stereo system is equipped with the Dolby B-type noise reduction system*. * Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

Photo: HCD-XG900AV

CD Section

TAPE Section

AEP Model

UK Model

HCD-XG900AV

E Model

Australian Model

HCD-XG100AV

Model Name Using Similar Mechanism HCD-XG80 CD Mechanism Type CDM37M-5BD32L Base Unit Name BU-5BD32L Optical Pick-up Name KSS-213DH Model Name Using Similar Mechanism HCD-XG80 Tape T r ansport Mechanism Type TCM-230PWR42

Amplifier section

HCD-XG900AV Front Speaker:

DIN power output (Rated)

Continuous RMS power output (Reference)

Music power output (Reference)

Center Speaker:

DIN power output (Rated)

Continuous RMS power output (Reference)

Music power output (Reference)

Rear Speaker:

DIN power output (Rated)

Continuous RMS power output (Reference)

Music power output (Reference)

90 + 90 watts (6 ohms at 1 kHz, DIN)

120 + 120 watts (6 ohms at 1 kHz, 10% THD)

200 + 200 watts (6 ohms at 1 kHz, 10% THD)

30 watts (8 ohms at 1 kHz, DIN)

40 watts (8 ohms at 1 kHz, 10% THD)

60 watts (8 ohms at 1 kHz, 10% THD)

30 + 30 watts (8 ohms at 1 kHz, DIN)

40 + 40 watts (8 ohms at 1 kHz, 10% THD)

60 + 60 watts (8 ohms at 1 kHz, 10% THD)

SPECIFICATIONS

HCD-XG100AV Front Speaker:

The following measured at AC 120/220/240 V, 50 Hz DIN power output (Rated)

Continuous RMS power output (Reference)

Center Speaker:

DIN power output (Rated)

Continuous RMS power output (Reference)

Rear Speaker:

DIN power output (Rated)

Continuous RMS power output (Reference)

Inputs DJ MIX IN*: (phono jacks) sensitivity 250 mV,

GUITAR IN: (phone jack) sensitivity 75 mV,

150 + 150 watts (6 ohms at 1 kHz, DIN)

200 + 200 watts (6 ohms at 1 kHz, 10% THD)

35 watts (8 ohms at 1 kHz, DIN)

50 watts (8 ohms at 1 kHz, 10% THD)

35 + 35 watts (8 ohms at 1 kHz, DIN)

50 + 50 watts (8 ohms at 1 kHz, 10% THD)

impedance 47 kilohms

impedance 470 kilohms

COMPACT DISC DECK RECEIVER

PHONO IN: (phono jacks) sensitivity 3 mV,

MIX MIC: (phone jack) sensitivity 1 mV,

VIDEO IN: (phono jack) sensitivity 250 mV,

GAME IN: (phono jack) sensitivity 250 mV,

MD IN: (phono jack) sensitivity 450 mV,

DVD INPUT FRONT, REAR, CENTER, WOOFER (phono jacks):

Outputs DJ MIX OUT*: (phono jacks) sensitivity 250 mV,

PHONES: (stereo phone jack) accepts headphones of 8

VIDEO OUT: (phono jack) voltage 250 mV

impedance 47 kilohms

impedance 10 kilohms

impedance 47 kilohms

sensitivity 450 mV, impedance 47 kilohms

impedance 1 kilohms

ohms or more

impedance 1 kilohm

– Continued on next page –

9-873-815-11 Sony Corporation

2001D0500-1 Home Audio Company C 2001.4 Shinagawa Tec Service Manual Production Group

HCD-XG100AV/XG900AV

MD OUT: (phono jacks) voltage 250 mV

WOOFER OUT (phono jack):

FRONT SPEAKER: accepts impedance of 6 to CENTER SPEAKER: accepts impedance of 8 to REAR SPEAKER: accepts impedance of 8 to

* AEP, UK and Mexican models only

Video section

Inputs VIDEO IN (phono jack): 1 V p-p, 75 ohms GAME IN (phono jack): 1 V p-p, 75 ohms

Output VIDEO OUT (phono jack):1 V p-p, 75 ohms

CD player section

System Compact disc and digital Laser Semiconductor laser

Wavelength 780 – 790 nm Frequency response 2 Hz – 20 kHz (±0.5 dB) Signal-to-noise ratio More than 90 dB Dynamic range More than 90 dB CD OPTICAL DIGITAL OUT (Square optical connector jack, rear panel) Wavelength: 660 nm Output level –18 dBm

Tape player section

Recording system 4-track 2-channel stereo Frequency response 40 – 13,000 Hz (±3 dB), (DOLBY NR OFF)

Tuner section

FM stereo, FM/AM superheterodyne tuner

FM tuner section

Tuning range 87.5 – 108.0 MHz Antenna FM lead antenna

Antenna terminals 75 ohm unbalanced Intermediate frequency 10.7 MHz

AM tuner section

Tuning range European, Middle Eastern, and Philippine models:

Other models: 531 – 1,602 kHz

Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency

General

Power requirements AEP, UK models: 230 V AC, 50/60 Hz Mexican model: 120 V AC, 50/60 Hz Australian model: 230 – 240 V AC, 50/60

Other models: 120 V, 220 V or 230 – 240

Power consumption HCD-XG900AV 200 watts

HCD-XG100AV 230 watts Dimensions (w/h/d) Approx. 355 × 425 × 450 Mass :

HCD-XG900AV Approx. 14.5 kg HCD-XG100AV Approx. 16.0 kg

Design and specifications are subject to change without notice.

impedance 1 kilohm voltage 1 V, impedance

1 kilohm 16 ohms 16 ohms 16 ohms

audio system (λ=780nm), Emission

duration: continuous

using Sony TYPE I cassette 40 – 14,000 Hz (±3 dB), using Sony TYPE II cassette

(50 kHz step)

531 – 1,602 kHz (with the interval set at 9 kHz)

(with the interval set at 9 kHz) 530 – 1,710 kHz (with the interval set at 10 kHz)

450 kHz

Hz V AC, 50/60 Hz

Adjustable with voltage selector

0.6 watts (at the power saving mode)

mm

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

The following caution label is located inside the unit.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

2

TABLE OF CONTENTS

HCD-XG100AV/XG900AV

1. SERVICING NOTES................................................ 4

2. GENERAL

Location of Controls ....................................................... 5

Setting the Time .............................................................. 6

3. DISASSEMBLY

3-1. Disassembly Flow ........................................................... 7

3-2. Case ................................................................................. 7

3-3. Front Panel Section ......................................................... 8

3-4. Cover (TC), Tape Mechanism Deck

(TCM-230PWR42) ......................................................... 8

3-5. MAIN Board, “Fan, D.C. (M901) (XG100AV)” ........... 9

3-6. MAIN Board (XG900AV) .............................................. 9

3-7. CD Mechanism Deck (CDM37M-5BD32L) .................. 10

3-8. Base Unit (BU-5BD32L) ................................................ 11

3-9. Disc Table........................................................................ 11

4. TEST MODE.............................................................. 12

5. MECHANICAL ADJUSTMENTS....................... 14

6. ELECTRICAL ADJUSTMENTS

Deck section .................................................................... 14

CD Section ...................................................................... 17

7. DIAGRAMS

7-1. Block Diagram – CD SERVO Section – ....................... 18

7-2. Block Diagram – TUNER/TAPE DECK Section – ...... 19

7-3. Block Diagram – MAIN Section (1/2) – ....................... 20

7-4. Block Diagram – MAIN Section (2/2) – ....................... 21

7-5. Block Diagram – DISPLAY/KEY CONTROL/

POWER SUPPLY Section – ........................................... 22

7-6. Note for Printed Wiring Boards and

Schematic Diagrams ....................................................... 23

7-7. Printed Wiring Board – BD Board – ............................. 24

7-8. Schematic Diagram – BD Board – ................................ 25

7-9. Printed Wiring Boards – CD MOTOR Section – .......... 26

7-10. Schematic Diagram – CD MOTOR Section – .............. 27

7-11. Printed Wiring Board – AUDIO Board – ...................... 28

7-12. Schematic Diagram – AUDIO Board – ......................... 29

7-13. Printed Wiring Board – LEAF SW Board –.................. 30

7-14. Schematic Diagram – LEAF SW Board –..................... 30

7-15. Schematic Diagram – MAIN Board (1/3) – .................. 31

7-16. Schematic Diagram – MAIN Board (2/3) – .................. 32

7-17. Schematic Diagram – MAIN Board (3/3) – .................. 33

7-18. Printed Wiring Board – MAIN Board – ........................ 34

7-19. Printed Wiring Board – PA Board – .............................. 36

7-20. Schematic Diagram – PA Board – ................................. 37

7-21. Printed Wiring Board – SURROUND Board –............. 38

7-22. Schematic Diagram – SURROUND Board –................ 39

7-23. Printed Wiring Boards – MIC/FRONT INPUT/

HEADPHONES Boards –............................................... 40

7-24. Schematic Diagram – MIC/FRONT INPUT/

HEADPHONES Boards – ............................................. 41

7-25. Printed Wiring Board – PANEL FL Board –................. 42

7-26. Schematic Diagram – PANEL FL Board – ................... 43

7-27. Printed Wiring Boards

– PANEL VR/ILLUMINATION Boards – ..................... 44

7-28. Schematic Diagram

– PANEL VR/ILLUMINATION Boards – ..................... 45

7-29. Printed Wiring Boards – TC-A/TC-B/CD-L/

CD-R (1)/CD-R (2) Boards – ......................................... 46

7-30. Schematic Diagram – TC-A/TC-B/CD-L/

CD-R (1)/CD-R (2) Boards – ......................................... 47

7-31. Printed Wiring Board – TRANSFORMER Section–.... 48

7-32. Schematic Diagram – TRANSFORMER Section– ....... 48

7-33. IC Pin Function Description ........................................... 54

8. EXPLODED VIEWS

8-1. Case, Back Panel Section................................................ 59

8-2. Front Panel Section-1...................................................... 60

8-3. Front Panel Section-2...................................................... 61

8-4. Chassis Section ............................................................... 62

8-5. CD Mechanism Deck Section (CDM37M-5BD32L) .... 63

8-6. Base Unit Section (BU-5BD32L) ................................... 64

8-7. Tape Mechanism Deck Section-1

(TCM-230PWR42) ......................................................... 65

8-8. Tape Mechanism Deck Section-2

(TCM230PWR42)........................................................... 66

9. ELECTRICAL PARTS LIST ............................... 67

3

HCD-XG100AV/XG900AV

PART No.

SECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objectiv e lens.

LASER DIODE AND FOCUS SEARCH OPERATION CHECK

Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times.

• MODEL IDENTIFICATION – Rear Panel –

MODEL PART No.

AEP and UK models 4-232-089-1 120 V AC area in E model 4-232-089-2 Singapore model 4-232-089-3 Mexican model 4-232-089-4 Australian model 4-232-089-5 Saudi Arabia model 4-232-089-6 Argentina model 4-232-089-7

[]

4

LOCATION OF CONTROLS – Front Panel –

SECTION 2

GENERAL

1

2

3456

789

HCD-XG100AV/XG900AV

This section is extracted from instruction manual.

q;

rd rs ra

r; el ek

ej eh

eg

ef ed es

ea

A EJECT Z/Z B EJECT wj (17) AUDIO L jack ws (26) AUDIO R jack wa (26) CD SYNC qj (18,19) DIRECT EQUALIZER 6 (21)

SALSA REGGAE SAMBA TANGO MOVIE GUITAR ROCK JAZZ

DANCE GAME DIRECTION ek (17~19,23) DISC SKIP w; (11,12,19) DISC 1~5 wl (11) DISPLA Y 4 (10,13,15) DOLBY NR ek (17,18) DSP rd (21) DVD 5.1 CH qf (28) EDIT ea (19) ENTER wk (14,16 ) ENTER/NEXT qg

(10,19,20,22,25,32) FLASH es (13) FLAT qg (21) FUNCTION qa

(8,11,12,18,19,23,26,27)

e;

GAME qs (24,26) GROOVE rs (21) GUITAR DISTORTION wk (24) GUITAR jack ef (24) GUITAR LEVEL ej (24) H SPEED DUB qj (18) IR receptor 2 Jog dial (AMS./>) ql

(11~13,19) LOOP ed (8,13) MIC LEVEL eh (23) MIX GUITAR/KARAOKE el (23,24) MIX MIC jack eg (23) NON STOP e; (12) P.FILE qg (21,22) PHONES jack qk PLAY MODE w; ( 11,12,19) POWER SAVE/DEMO

(STANDBY) 3 (10) PRO LOGIC qf ( 10,22) PTY wf (16) *AEP, UK model only PUSH OPEN wh (11) REPEAT w; (11) SLEEP 8 (24) SPECTRUM ANALYZER 5 (23)

wh

qa qs qd qf

qg

qh qj qk

ql w;

wawswdwfwgwjwkwl

STEREO/MONO wf (15) SUPER WOOFER ra ( 21,27) SUPER WOOFER MODE r; (21) TIMER SELECT 9 (20,25) TUNER/BAND wg(14,15,18) TUNER MEMORY wk (14) TUNING MODE wf (14,15) VIDEO jack wd (26) VOLUME control qd (15)

BUTTON DESCRIPTIONS

@/1 1

c/CLOCK SET 7

v/V/b/B q; z REC qh X qh m /M, AMS./>

(TAPE A/B)

h/H qhek x qhw;ek m /M HX w;

+/– wg

(CD)

qhek

w;

5

HCD-XG100AV/XG900AV

– Rear Panel –

1

2 3 4 5 6 7 8

9

0

Remote control

wl wk

wj wh wg wf wd

ws wa

w; ql

qk

qa

1

23

4

5 6 7 8

9 q; qa

qs qd

qf qg

qh

qj

qs

1 ANTENNA terminal 2 DJ MIX RETURN/SEND jack (AEP, UK Mexican models) 3 SUB WOOFER OUT jack 4 PHONO IN jack 5 MD IN/OUT jack 6 VIDEO/AUDIO IN jack 7 VIDEO OUT jack 8 DVD INPUT VIDEO/FRONT/REAR/CENTER/WOOFER jack 9 CD DIGITAL OUT OPTICAL terminal 0 FRONT SPEAKER terminal qa REAR/CENTER SURROUND SPEAKER terminal qs VOLTAGE SELECTOR switch

(120 V AC area in E, Saudi Arabia, Singapore, Argentina models)

Setting the time

1

Turn on the system.

2

Press c/CLOCK SET.

When you set the time for the first time, skip to step 5.

3

Press v/V repeatedly to select “SET CLOCK.”

4

Press ENTER/NEXT.

5

Press v/V repeatedly to set the hour.

6

Press ENTER/NEXT.

The minute indication flashes.

7

Press v/V repeatedly to set the minute.

8

Press ENTER/NEXT.

The clock starts working.

Tip

If you’ve made a mistake or want to change the time, start over from step 2.

Note

The clock settings are canceled when you disconnect the power cord or if a power failure occurs.

CD H wj (11) CENTER LEVEL +/– wa (10) CHECK w; (12) CLEAR ql (12) DECK A hH wg (17) DECK B hH wf (17) D.SKIP q; (11,12,19)

(21)

DSP qs FILE SELECT ON/OFF qj (21) FILE SELECT F/f qk (13) FLASH qg (13) FUNCTION wk

(8,11,12,18,19,23,26,27) LOOP qg (13) MD H wd MD X wd MD x wd PRO LOGIC qa (10,22)

6

REAR LEVEL +/– ws (10) SLEEP 1 (24) SUPER WOOFER qd (21,27) T.TONE qf (10) TUNER/BAND wh(14,15,18) TUNING +/– 5 (15) TV CH +/– 5 (28) TV/VIDEO 2 (28) TV VOL +/– wl (28) TV @/1 3 (28) VOL +/– qh (15)

BUTTON DESCRIPTIONS

@/1 4 X 6 x 7 ./> 8 m/M 9

• This set can be disassembled in the order shown below.

)

3-1. DISASSEMBLY FLOW

SET

3-2. CASE

(Page 7)

3-3. FRONT PANEL SECTION

(Page 8)

HCD-XG100AV/XG900AV

SECTION 3

DISASSEMBLY

3-4. COVER (TC),

TAPE MECHANISM DECK (TCM-230PWR42) (Page 8)

Note: Follow the disassembly procedure in the numerical order given.

3-5. MAIN BOARD,

“FAN, D.C. (M901) (XG100AV)” (Page 9)

3-2. CASE

6

case

3-6. MAIN BOARD

(XG900AV) (Page 9)

3-7. CD MECHANISM DECK

(CDM37M-5BD32L) (Page 10)

3-8. BASE UNIT

(BU-5BD32L) (Page 11)

3-9. DISC TABLE

2

five screws (BVTT3

(Page 11)

×

6)

1

three screws (CASE3 TP2)

5

4

5

4

1

three screws (CASE3 TP2)

3

two screws (BVTP3

×

8

7

HCD-XG100AV/XG900AV

)

3-3. FRONT PANEL SECTION

3

two screws (BVTP3

×

8)

4

lug

1

wire (flat type) (17 core) (CN304)

1

wire (flat type) (13 core) (CN431)

wire (flat type) (15 core) (CN303)

2

two connectors (CN452, 702)

3

4

screw (BVTP3

two lugs

×

8

6

7

front panel section

5

four screws (BVTP3

×

claw

8)

3-4. COVER (TC), TAPE MECHANISM DECK (TCM-230PWR42)

4

two screws (BVTP3

×

8)

2

5

screw (BVTP3

3

wire (flat type) (17 core) (CN1001)

×

8)

3

wire (flat type) (15 core (CN601)

connector (CN806)

4

two screws

1

five claws

2

cover (TC)

(BVTP3

5

tape mechanism deck (TCM-230PWR42)

×

8)

8

3-5. MAIN BOARD, “FAN, D.C. (M901) (XG100AV)”

1

wire (flat type) (13 core) (CN441)

8

back panel

7

9

wire (flat type) (19 core) (CN411)

fan, D.C. (M901)

4

3

seven screws (BVTP3

Mexican models

×

8)

HCD-XG100AV/XG900AV

2

jumper plug

3

screw (BVTP3

3

three screws (BVTP3

6

two screws (BVTP3

3

three screws (BVTP3

3

three screws (BVTP3

qa

connector (CN180)

×

8)

×

8)

×

8)

×

8)

×

8)

3-6. MAIN BOARD (XG900AV)

6

wire (flat type) (19 core) (CN411)

5

back panel

0

connector (CN412)

1

wire (flat type) (15 core) (CN441)

4

3

six screws (BVTP3

qd

×

8)

5

connector (CN903)

qf

MAIN board

qs

two screws (BVTP3

two connectors (CN901, 902)

2

jumper plug

3

×

8)

screw (BVTP3

three screws (BVTP3

×

8)

×

8)

×

8)

7

connector (CN412)

8

9

0

two connectors (CN901, 902)

connector (CN180)

MAIN board

qa

two screws (BVTP3

×

8)

9

HCD-XG100AV/XG900AV

3-7. CD MECHANISM DECK (CDM37M-5BD32L)

wire (flat type)

1

(19 core) (CN411)

4

three screws (BVTP3

×

8)

5

6

3

three screws

×

(BVTP3

7

8)

Open the cable clamp.

2

connector (CN412)

9

CD mechanism deck

(CDM37M-5BD32)

8

five screws (BVTP3 × 8)

5

4

two screws (BVTP3

×

8)

10

3-8. BASE UNIT (BU-5BD32L)

w

1 two screws

(BVTP3 × 8)

A

2 two brackets (BU)

3 step screw

4 disc table

A

HCD-XG100AV/XG900AV

3 base unit

(BU-5BD32L)

2 boss

3-9. DISC TABLE

Note: When the disc table is installed, adjust the positions of roller cam

and mark B as shown in the figure, then set to the groove of disc table.

1 BU fitting scre

11

HCD-XG100AV/XG900AV

SECTION 4

TEST MODE

[MC Cold Reset]

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning the set to the customer.

Procedure:

1. Turn the power ON or set to the DEMO mode.

2. Press three buttons of [ /CLOCK SET], [ENTER/NEXT], and

?/1 simultaneously.

3. The set is reset, and displays “COLD RESET”, then becomes

DEMO mode.

[MC Hot Reset]

• This mode resets the set with the preset data kept stored in the

memory. The hot reset mode functions same as if the power cord is plugged in and out.

Procedure:

1. Turn the power ON or set to the DEMO mode.

2. Press three buttons of [ /CLOCK SET], [ENTER/NEXT],

and [DISC 1] simultaneously.

3. The set is reset, and becomes standby state.

[Change-over the AM Tuning Interval] (EXCEPT AEP, UK, and Saudi Arabia models)

• The AM tuning interval can be changed over 9 kHz or 10 kHz.

Procedure:

1. Press the ?/1 button to turn the power ON.

2. Select the function “TUNER”, and press the [TUNER/BAND]

button to select the BAND “AM”.

3. Press the ?/1 button to turn the power OFF.

4. Press the [ENTER/NEXT] and ?/1 buttons simultaneously,

and the display on the fluorescent indicator tube changes to “AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning interval is changed over.

c

[CD Delivery Mode]

• This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.

Procedure:

1. Press the ?/1 button to turn the power ON.

2. Press the [LOOP] and ?/1 buttons simultaneously.

3. A message “LOCK” is displayed on the fluorescent indicator

tube, and the CD delivery mode is set.

[LED and Fluorescent Indicator Tube All Lit, Key Check Mode]

Procedure:

1. Press three buttons of [ /CLOCK SET], [ENTER/NEXT],

and [DISC 2] simultaneously.

2. LEDs and fluorescent indicator tube are all turned on.

Press the [DISC 2] button, and the key check mode is activated.

3. In the key check mode, the fluorescent indicator tube displays

“K 0 J0 V0”. Each time a button is pressed, “K” value increases. However , once a button is pressed, it is no longer tak en into account. “J” value increases like 1, 2, 3 ... if turn the JOG dial clockwise, or it decreases like 0, 9, 8 ... if turn the JOG dial counterclockwise. “V” value increases like 1, 2, 3 ... if turn the [VOLUME] dial clockwise, or it decreases like 0, 9, 8 ... if turn the JOG dial counterclockwise.

4. To release from this mode, press three buttons in the same

manner as step 1, or disconnect the power cord.

c

12

HCD-XG100AV/XG900AV

[Aging Mode]

This mode can be used for operation check of tape deck section. Tape deck section work in parallel.

• If an error occurred: The aging operation stops and display then status.

• If no error occurs: The aging operation continues repeatedly.

Procedure:

1. Load the tapes into the decks A and B respectively.

2. Press the [FUNCTION] button to select the function “CD”.

3. Press the [PLAY MODE] button to set the “ ALL DISCS” mode,

and press the [REPEAT] button to “REPEAT” off.

4. Press three buttons of [ /CLOCK SET], [ENTER/NEXT],

c

and [DISC 4] simultaneously.

5. The aging mode is activ a ted, if the indicator of disc tray num-

ber on the fluorescent indicator tube is blinking.

6. To release from the aging mode, press the ?/1 button to turn

the power OFF and operate the cold reset. (Refer to the “MC Cold Reset”)

1. Display at the Aging Mode

• Display operating state of tape deck section alternately.

• If an error occurred, stop display.

2. Tape Deck Section

• The sequence during the aging mode is following as below.

• If an error occurred, stop display that step.

Aging mode sequence (Tape deck section) :

Rewind the tape A and B

“TAPE A AG-1”

Shut off

FWD play the tape A

“TAPE A AG-2”

2 minutes

Fast forward the tape A

“TAPE A AG-3”

Shut off or 20 seconds

REV play the tape A

“TAPE A AG-4”

2 minutes

Rewind the tape A

“TAPE A AG-5”

Shut off

FWD play the tape B

“TAPE B AG-2”

2 minutes

Fast forward the tape B

“TAPE B AG-3”

Shut off or 20 seconds

REV play the tape B

“TAPE B AG-4”

2 minutes

Rewind the tape B

“TAPE B AG-5”

Shut off

Note: “TAPE * AG-*” is display of each step.

13

HCD-XG100AV/XG900AV

SECTION 5

MECHANICAL ADJUSTMENTS

SECTION 6

ELECTRICAL ADJUSTMENTS

Precaution

1. Clean the following parts with a denatured alcohol-moistened swab:

record/playback heads pinch rollers erase head rubber belts capstan idlers

2. Demagnetize the record/playback head with a head demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.

4. After the adjustments, apply suitable locking compound to the parts adjusted.

5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.

Torque Measurement

Mode Torque Meter Meter Reading

FWD CQ-102C (31 to 71 g•cm)

FWD back tension

REV CQ-102RC (31 to 71 g•cm)

REV back tension

FF/REW CQ-201B (71 to 143 g•cm)

FWD tension CQ-403A (100 g or more)

REV tension CQ-403A (100 g or more)

CQ-102C (2 to 6 g•cm)

CQ-102RC (2 to 6 g•cm)

3.1 to 6.96 mN•m

(0.43 – 0.98 oz•inch)

0.20 to 0.58 mN•m

(0.03 – 0.08 oz•inch)

3.1 to 6.96 mN•m

(0.43 – 0.98 oz • inch)

0.20 to 0.58 mN•m

(0.03 – 0.08 oz • inch)

6.97 to 14.02 mN•m

(0.99 – 1.99 oz • inch)

9.80 mN•m

(3.53 oz or more)

9.80 mN•m

(3.53 oz or more)

DECK SECTION

0 dB = 0.775 V

Precaution

1. Demagnetize the record/playback head with a head demagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.

3. After the adjustments, apply suitable locking compound to the parts adjust.

4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)

6. The adjustments should be performed for both L-CH and RCH.

7. Switches and controls should be set as follows unless otherwise specified.

8. Set to the DOLBY NR OFF.

9. Set to the test mode. (1) Press the ?/1 button to turn the power ON. (2) Select the function “TAPE A or B”. (3) Press the button of [ /CLOCK SET], [ENTER/NEXT],

c

and [DISC 3] simultaneously , to set the tape deck test mode and displays “TEST MODE” on the fluorescent indicator tube.

(4) To release from the test mode, press the ?/1 button.

• Test Tape

Tape Signal Used for

P-4-A100 10 kHz, – 10 dB Azimuth Adjustment

WS-48B 3 kHz, 0 dB Tape Speed Adjustment

P-4-L300 315 Hz, 0 dB Playback Level Adjustment

14

HCD-XG100AV/XG900AV

+

–

set

test tape WS-48B (3 kHz, 0 dB)

MAIN board MD OUT jack (J701) L-CH, R-CH

frequency counter

r

Record/Playback Head Azimuth Adjustment

DECK A DECK B

Note: Perform this adjustments for both decks

Procedure:

1. Mode: Playback (FWD)

2. T urn the adjustment screw and check output peaks. If the peaks

test tape P-4-A100 (10 kHz, – 10 dB)

MAIN board MD OUT jack (J701) L-CH, R-CH

set

level mete

+

–

do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.

Output level

within 1dB

L-CH peak

Adjustment Location:Playback Head (Deck A).

Record/Playback/Erase Head (Deck B).

forward

reverse

Tape Speed Adjustment DECK B

Mode: Playback

R-CH

Screw position

peak

L-CH peak

R-CH peak

Screw position

3. Mode: Playback

MAIN board test tape P-4-A100 (10 kHz, – 10 dB)

L-CH

set

R-CH

in phase 45° 90 ° 135° 180°

MD OUT jack (J701)

L-CH

R-CH

waveform of oscilloscope

good

oscilloscope

wrong

H

V

4. Repeat step 1 to 3 in playback (REV) mode.

5. After the adjustments, apply suitable locking compound to the pats adjusted.

1. Insert the WS-48B into the deck B.

2. Press the H button on the deck B.

3. Press the [H SPEED DUB] button in playback mode. Then at HIGH speed mode.

4. Adjust RV1001 on the LEAF SW board do that frequency counter reads 6,000 ± 180 Hz.

5. Press the [H SPEED DUB] button. Then back to NORMAL speed mode.

6. Adjust RV1002 on the LEAF SW board so that frequency counter reads 3,000 ± 90 Hz.

Adjustment Location: LEAF SW board Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)

(WS-48B)

Playback Level Adjustment DECK A DECK B

Procedure:

Mode: Playback

test tape P-4-L300 (315 Hz, 0 dB)

set

MAIN board MD OUT jack (J701) L-CH

level mete

+

–

Deck A is RV311 (L-CH), Deck B is RV301 (L-CH) so that adjustment within specification values as follows.

Specification Values:

J701 PB level: 301.5 to 338.3 mV (– 8.2 to – 7.2 dB) level difference between the channels: within ± 0.5 dB

Adjustment Location: AUDIO board

15

HCD-XG100AV/XG900AV

r

REC Bias Adjustment DECK B

Procedure:

1. Mode: Record FUNCTION: VIDEO

MAIN board VIDEO AUDIO IN jack (J701) L-CH, R-CH



50 mV (– 23.8 dB)

 

600 Ω

set

blank tape CN-123

AF OSC

1) 315 Hz

2) 10 kHz

attenuator

2. Mode: Playback

recorded portion

set

MAIN board MD OUT jack (J701) L-CH, R-CH

level mete

+

–

3. Confirm playback the signal recorded in step 1 become specification values as follows. If these values are out of specification v alues, adjust the R V341 (L-CH) and RV441 (R-CH) on the AUDIO board to repeat steps 1and 2.

Specification values: Playback output of 315 Hz to playback

output of 10 kHz: ± 0.5 dB

Adjustment Location: AUDIO board

Specification values:

J701 PB level: 47.2 to 53.0 mV (– 24.3 to – 23.3 dB)

Adjustment Location: MAIN board

– MAIN BOARD (Conductor Side) –

VIDEO

AUDIO IN

L/R

J701

REC LEVEL



IC301

RV351

R-CH

MD OUT

RV301

L-CH

L/R

        

– AUDIO BOARD (Component Side) –

RV441

RV301

PB LEVEL (L)

– DECK B –

IC602

RV341

RL



REC BIAS

CN601

RV311

PB LEVEL (L)

– DECK A –

REC Level Adjustment DECK B

Procedure:

1. Mode: Record FUNCTION: VIDEO

MAIN board VIDEO AUDIO IN jack (J701) L-CH, R-CH

AF OSC

315 Hz, 50 mV (– 23.8 dB)

600 Ω

attenuator

blank tape CS-123

set

2. Mode: Playback

recorded portion

set

MAIN board MD OUT jack (J701) L-CH, R-CH

level mete

+

–

3. Confirm playback the signal recorded in step 1 become specification values as follows. If these values are out of specification v alues, adjust the R V301 (L-CH) and R V351 (R-CH) on the MAIN board to repeat steps 1 and 2.

– LEAF SW BOARD (Component Side) –

TAPE SPEED



(NORMAL) (HIGH)

RV1002



RV1001

CN1001

16

HCD-XG100AV/XG900AV

e

)

CD SECTION

Note:

1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10 MΩ impedance.

4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.

S-Curve Check

oscilloscop

BD board

TP (FE) TP (VC)

Procedure:

1. Connect oscilloscope to TP (FE) and TP (VC).

2. Connect between TP (FE1) and TP (VC) by lead wire.

3. Connect between TP (A GCCON) and TP (GND) by lead wire.

4. Turn the power ON.

5. Load a disc (YEDS-18) and actuate the focus search. (In con-

sequence of open and close the disc tray, actuate the focus search)

6. Cofirm that the oscilloscope w aveform (S-curve) is symmetri-

cal between A and B. And confirm peak to peak level within 4 ± 1 Vp-p.

S-curve waveform

+ –

symmetry

E-F Balance (1 Track Jump) Check

oscilloscope

(DC range)

BD board

TP (TE) TP (VC)

+

–

Procedure :

1. Connect oscilloscpe to TP (TE) and TP (VC).

2. Turn the power ON.

3. Load a disc (YEDS-18) and playback the number five track.

4. Press the H X button. (Becomes the 1 track jump mode)

5. Confirm that the level B and A (DC voltage) on the oscilloscope waveform.

1 track jump waveform

B

0V

level = 1.3 ± 0.6 Vp-p symmetry

Specified level: × 100 = less than ± 22%

A B

center of waveform

A (DC voltage

6. After check, remove the lead wire connected in step 1.

A

within 4 ± 1 Vp-p

B

7. After check, remove the lead wire connected in step 2 and 3.

Note: • Try to measure several times to make sure than the ratio of A : B

or B : A is more than 10 : 7.

• Take sweep time as long as possible and light up the brightness to obtain best waveform.

RF Level Check

oscilloscop

(AC range)

BD board

TP (RF) TP (VC)

+

–

Procedure:

1. Connect oscilloscope to TP (RF) and TP (VC).

2. Connect between TP (A GCCON) and TP (GND) by lead wire.

3. Turn the power ON.

4. Load a disc (YEDS-18) and press the H X button to play.

5. Confirm that the oscilloscope w aveform is clear and chec k RF signal level is correct or not.

6. After check, remove the lead wire connected in step 2.

Note: Clear RF signal waveform means that the shape “◊” can be clearly

distinguished at the center of the waveform.

VOLT/DIV: 200 mV TIME/DIV: 500 ns (with the 10: 1 probe in use)

level:

1.45 ± 0.3 Vp-p

Checking Location:

– BD BOARD (Side B) –

TP (VC)

IC102

TP (RF)

IC103

TP (TE)

TP (AGCCON)

TP (FE)

TP (FE1)

TP (GND)

1717

HCD-XG100AV/XG900AV

SECTION 7

DIAGRAMS

7-1. BLOCK DIAGRAM – CD SERVO Section –

DETECTOR

A

B

C

D

I-V AMP

F

E

OPTICAL PICK-UP BLOCK

(KSS-213DH)

LASER DIODE

LD

PD

LOUT1

LOUT2

XTAI

XTAO

(AEP, UK, Mexican)

72

75

R-CH

66

67

16.9344MHz

J705

R-CH

(EXCEPT AEP, UK, Mexican)

X101

IC781

CD DIGITALOUT

OPTICAL

TRANSCEIVER

IC781

L

R

L

R

SEND

RETURN

CD-L

DJ MIX

A

(Page 20)

FILTER

RF AMP,

CD D+5V

7

4

2

1

5

10

6

10

11

AUTOMATIC

POWER

CONTROL

Q101

FOCUS/TRACKING ERROR AMP

A

5

B

6

C

7

D

8

F

F I-V AMP

E

E I-V AMP

3

IC103

RF

SUMMING

AMP

ERROR AMP

TRACKING

ERROR AMP

LD

APC LD

AMP

FOCUS

APC PD

AMP

RF EQ

AMP

HOLD SW

RFO

LDON

16

FE

14

TE

13

21

22

PD

4

RFAC

ASYI

ASYO

DIGITAL

CLV

MDP

26

ASYMMETRY CORRECTION

XRST

3

PROCESSOR

XLON

14 5 6

51

49

48

54 56

FILO

SUBCODE

DATA

53

PCO

CLTV

DIGITAL

PLL

CPU INTERFACE

XLAT

CLOK

7

SENS

8

DIGITAL SIGNAL PROCESSOR,

DIGITAL FILTER, D/A CONVERTER

55

FILI

SERVO AUTO

EFM

DEMODULATOR

SEQUENCER

SQSO

SQCK

SCOR

20

1 2

16K

RAM

IC101 (1/2)

CORRECTOR

SERVO

INTERFACE

SCLK

COUT

9 21

D/A

INTERFACE

INTERNAL BUS

ERROR

SSTP

EMPH

WFCK

GFS

64 15

27

ON :

18

S101

(LIMIT)

When the optical pick-up is inner position.

PCMD

BCK LRCK C2PO

SERIAL

IN

INTERFACE

DIGITAL

62 63 61 19

OUT

DOUT

60

DIGITAL

FILTER,

NOISE SHAPER

TO MIRR/DFCT/ FOK DETECTOR

PWM

&

INTEGRATOR

AOUT1

AOUT2

70

77

CLOCK

GENERATOR

AIN1

71

76

AIN2

BUFFER

TIMING

LOGIC

2-AXIS DEVICE

(TRACKING)

(FOCUS)

M101

(SPINDLE)

M102

(SLED)

FOCUS/TRACKING COIL DRIVE,

SPINDLE/SLED MOTOR DRIVE

IC102

CH4OUTF

15

M

16

17

18

12

11

14

13

CH4OUTR

CH3OUTF

CH3OUTR

CH2OUTF

CH2OUTR

CH1OUTF

CH1OUTR

MOTOR

DRIVE

MOTOR

DRIVE

COIL

DRIVE

COIL

DRIVE

CH4SIN

CH3FIN

CH3RIN

CH2FIN

CH2RIN

CH1FIN

CH1RIN

MUTE

25

43

39

40

41

FE

TE

SE

24

23

SFDR

28

SRDR

29

5

6

2

3

20

TFDR

30

TRDR

31

FFDR

32

33

FRDR

FOCUS/TRACKING/SLED

RFDC

A/D

CONVERTER

PWM GENERATOR

SERVO DSP

FOCUS/TRACKING/SLED

DIGITAL SERVO

PROCESSOR

IC101 (2/2)

MIRR/DFCT/

FOK

DETECTOR

TO SERVO INTERFACE

FOK

MIRR

DFCT

24 22 23

33

SQ-CLK

32

SQ-DATA

19

SCOR

56

SENS

37

CD-CLK

58

XLT CD-DATA

35

HOLD

57

SYSTEM CONTROLLER

(CD MECHANISM CONTROL)

IC501 (1/5)

59

XRST

T-SENS

ENC3/UP-SW

ENC2/DISC-LED

TBL-L

TBL-R

DISC TABLE

61

68

69

63

65

SENSOR

IC202

S201

(UP)

LED DRIVE

Q201

TABLE MOTOR DRIVER

IC201

IN1

9

MOTOR

IN2

1

DRIVE

D201

(DISC No.)

OUT1

OUT2

7

3

M201

M

(TABLE)

• R-ch is omitted due to same as L-ch.

• SIGNAL PATH

: CD PLAY (ANALOG OUT)

: CD PLAY (DIGITAL OUT)

1818

7-2. BLOCK DIAGRAM – TUNER/TAPE DECK Section –

RV311

HP101

(PLAYBACK)

L-CH

R-CH

HRPE101 (1/2)

(RECORD/PLAYBACK)

L-CH

R-CH

PB EQ AMP

(DECK A)

IC611 (2/2)

PB EQ AMP

(DECK A)

IC611 (1/2)

PB EQ AMP

(DECK B)

IC601 (2/2)

PB EQ AMP

(DECK B)

IC601 (1/2)

REC/PB SWITCHING

IC602

1

3

R-CH

PB LEVEL (L)

(DECK A)

RV301

PB LEVEL (L)

(DECK B)

4

DECK PROCESS,

DECK A/B SELECT, PB/REC EQ AMP,

DOLBY NR AMP, ALC, AMS

A IN (L)

48

B IN (L)

46

A IN (R)

51

B IN (R)

53

BIAS (N)

33

BIAS (C)

32

BIAS (M)

31

A 120/70

19

S1004

(DECK A 120/70)

S1008

(DECK B 120/70)

IC301

R-CH

BIAS

CONTROL

CIRCUIT

B NORM/CROM

ALC ON/OFF

NORM/HIGH

PB A/B

1516182022 23242517

70

120

R-CH

NR ON/OFF

BIAS ON/OFF

RM ON/OFF

L.P.F.

BUFFER

AMS

CIRCUIT

REC/PB/PASS

LM ON/OFF

+

28

27

26

MAOUT

MSIN

MSOUT

R IN (L)

43

ALC (L)

44

DOLBY PASS

ALC

R OUT (L)

35 34

DOLBY NR

AMP

CIRCUIT

ALC

IN (L)

REC OUT (L)

39

RV301

REC LEVEL (L)

(DECK B)

EQ IN (L)

38

REC

EQ AMP

PB OUT (L)

EQ OUT

HCD-XG100AV/XG900AV

• R-ch is omitted due to same as L-ch.

• SIGNAL PATH

: TUNER (FM/AM)

40

(L)

36

PB-L

REC-L

B

(Page 20)

C

(Page 20)

: PLAYBACK (DECK A) : PLAYBACK (DECK B) : RECORD

REC BIAS (R)

HRPE101 (2/2)

(ERASE)

(XG900AV)

(XG100AV)

FM

75Ω

AM

RV441

(DECK B)

COAXIAL

FM 75Ω

R-CH

ANTENNA

2

RV341

REC BIAS (L)

(DECK B)

BIAS OSC

T621

FM/AM TUNER UNIT

FM ANT

AM ANT

(XG900AV)

BIAS OSC

Q621, 622

ST-R

ST-MUTE

STEREO

TUNED

ST-DIN

ST-DOUT

ST-CLK

ST-CE

RDS-DATA

RDS-INT

REC BIAS

SWITCH

Q623

ST-L

C331, L331

BIAS

TRAP

R-CH

ST-MUTE STEREO TUNED

ST-DIN ST-DOUT ST-CLK ST-CE

RDS-DATA RDS-INT

A+7V

D+5V

(UNSW)

100

TC-RELAY

(DECK A PLAY)

8584838281 807978

ALC

PB-A/B

EQ-H/N

A-PLAY-SW

87

S1001

S1002

(DECK B PLAY)

BIAS

REC-MUTE

B-PLAY-SW

86

TC-MUTE

R/PB/PAS

NR-ON/OFF

(DECK A HALF)

S1003

77

AMS-IN

88

DETECT SENSOR

A-HALF

(DECK B HALF)

(DECK A REC)

(DECK B REC)

ROTATION

(DECK A)

IC1001

91

A-SHUT

S1006

S1005

S1009

ROTATION

DETECT SENSOR

(DECK B)

IC1002

90

B-SHUT

(CD MECHANISM CONTROL)

B-HALF

89

TRIGGER PLUNGER

PLUNGER DRIVE

SYSTEM CONTROLLER

IC501 (2/5)

DECK A

TRIGGER

(DECK A)

Q333, 334

73

A-TRG

TRIGGER PLUNGER

DECK B

TRIGGER

PLUNGER DRIVE

(DECK B)

Q331, 332

72

B-TRG

ST-CE

ST-CLK

ST-DOUT

ST-DIN

TUNED

STEREO

ST-MUTE

49 50 51 54 53 55 52 21 20

ST-CE

ST-CLK

ST-DOUT

ST-DIN

TUNED

STEREO

ST-MUTE

Q335

RDS-DATA

RDS-INT

RDS-DATA

76

CAP-M-H/L

(XG900AV)

RDS-INT

CT-L

RV1001

TAPE SPEED

(HIGH)

CAPM-CNT2

(Page 20)

D

CAPSTAN MOTOR

CONTROL SWITCH

Q1001

74

MOTOR DRIVE

RV1002

TAPE SPEED

(NORMAL)

CAPSTAN

Q336, 339

M

M1

(CAPSTAN)

1919

HCD-XG100AV/XG900AV

7-3. BLOCK DIAGRAM – MAIN Section (1/2) –

(Page 22)

(Page 18)

(Page 19)

MD IN

PHONO

IN

VIDEO

AUDIO IN

GAME INPUT AUDIO

DVD INPUT FRONT

VIDEO IN

VIDEO OUT

REAR

VIDEO

DVD INPUT VIDEO

GAME INPUT VIDEO

CENTER

WOOFER

E

A

B

D

J701 (1/2)

L

R

L

R

L

R

J804 (2/2)

L

R

J703 (1/2)

L

R

J702 (1/2)

J804 (1/2)

J702 (2/2)

J703 (2/2)

L

R

DISTORTION

J802

GUITAR

J801

MIX MIC

CD-L

PB-L

ST-L

VIDEO SELECT

SWITCH,

VIDEO AMP

IC191

DVD

INPUT

R-CH

DISTORTION

ON/OFF SWITCH

Q880 – 883

FUNCTION SELECT

12 14 15

IN1

1

IN2

4

IN3

6

REAR-L

CENTER

WOOFER

PHONO EQ AMP

IC601

SWITCH

IC181

X0

X

X1 X2

13

AB

10 9

LOGIC

CTLA

CTLB

CTLC

532

CBACBA

VOUT

GUITAR AMP

IC853

GUITAR AMP

IC852

RV601

GUITAR LEVEL

MIC AMP

IC850 (1/2)

INPUT SELECT SWITCH,

GRAPHIC EQUALIZER CONTROL,

ELECTRICAL VOLUME

IN D2

66

IN C2

67

IN B2

68

IN E2

65

IN A2

69

IN F2

64

X501

32.768kHz

X502

16MHz

10

11

10

13

15

46 45

28

RV602

MIC LEVEL

IC101

INPUT

SELECT

SWITCH

R-CH

493-DATA

XC-OUT

XC-IN

X-OUT

X-IN

SYSTEM CONTROLLER

(CD MECHANISM CONTROL)

FUNC SEL0 FUNC SEL1

V MUTE

493-CLK 493-LAT

DBFB-H/L

SW-MODE

IC501 (3/5)

PL-DATA

SOUND

CONTROL

CIRCUIT

PL-CLK

PL-LAT

MIC AMP

IC850 (2/2)

47 48 38

7

34

24 23 25

DATA

CLK LAT

KEY IN2

60 5

R-CH

KEY IN1

D501 D534

WOOFER

CENTER

REAR-L

2 58 57

MIC IN

+

L+R

+

VRSW IN

80

SWIN

99

LTIN

74

CIN

76

SLIN

77

KEY OUT 1 KEY OUT 2

R-CH

L+R

2

DOLBY SURROUD

PRO LOGIC

PROCESSOR

30

6

59

AUTO-BALANCE

L–R

IC201

REC A2

SW OUT

INPUT

GRAPHIC

EQUALIZER

CONTROL

CIRCUIT

R-CH

DSEL

OUT

+

REC B2

F OUT2

42 41

SWVOL

IN

SELECTOR

COMMAND

REQ

LAT

TRIMMER,

VOLUME

ADAPTIVE

MATRIX

S

DIN

R-CH

1615

NOISE

SEQUENCER

26 27

CPU

INTERFACE

DATA

SCK

22 23 24 8 7 6

DATA

CLK

VOL IN2

COMMAND

L

R

C

10KBIT S-RAM

LOGIC

CIRCUIT

PSEUDO STEREO

PS

RIN

VOLUME

CONTROL

CENTER

MODE

CONTROL

PS LIN

DELAY

VOLUME

R-CH

+

CPU

INTERFACE

DATA

CLOCK

R-CH

LATCH

34

DVOL

OUT

BASS BOOST

DBFB CONTROL

C

SL

CONTROL

CIRCUIT

BB B2,

BB A2

38, 39

SWITCH

Q111

SUPER

WOOFER

BUF IN2

373233

BASS WOOFER

CONTROL SWITCH

Q115

R-CH

MODIFIED

BNR

IN

4240

CVOL

IN

SLVOL

IN

TRIMMER,

VOLUME

TRIMMER,

VOLUME

45

1011

OUT2

R-CH

BUF

72

36

FEED BACK

SWITCH

Q112

R-CH

D803

+

R-CH

+

SWVOL OUT

R-CH

CVOL OUT

SLVOL OUT

LOUT

REC-L

SPEANA

R-CH

L IN

C

F

J701 (2/2)

G

(Page 19)

(Page 22)

L

MD OUT

R

(Page 21)

• R-ch is omitted due to same as L-ch.

• SIGNAL PATH

: TUNER (FM/AM)

: CD PLAY : TAPE PLAY : RECORD : MIC INPUT

FEED BACK

17

MUTING

Q731

SW-

1

3

9

MUTING

Q281

MUTING

Q271

MUTING

TAMUTING

(Page 21)

H

J704

SUB WOOFER

OUT

(Page 21)

J

C

(Page 21)

K

SL

(Page 21)

L

(Page 21)

M

2020

7-4. BLOCK DIAGRAM – MAIN Section (2/2) –

HCD-XG100AV/XG900AV

(Page 20)

H

M

J

G

FEED BACK

TA-MUTING

SW-MUTING

L IN

STK-POWER

HP MUTE

SYSTEM CONTROLLER

(CD MECHANISM CONTROL)

IC501 (4/5)

LINE-MUTE

AC-CUT

RESET

PROTECT

F-RELAY

HP-IN

REAR-RELAY

• R-ch is omitted due to same as L-ch.

• SIGNAL PATH

: AUDIO

R-CH

POWER AMP

STANDBY SWITCH

Q803, 804, 834

EVER +5V

IC801

R-CH

+

R-CH

TH831

+

TEMPERATURE

DETECT SWITCH

Q831, 832

OVER LOAD

DETECT

Q801, 851

DC DETECT

SWITCH

Q433, 434

D401

OVER LOAD

DETECT SWITCH

Q432

PROTECT SWITCH

Q439

MUTING CONTROL

OVER LOAD

DETECT SWITCH

Q437

FRONT SPEAKER PROTECT

RELAY DRIVE

Q401, 402

SWITCH

Q833

PROTECT SWITCH

Q431

HEADPHONE

MUTING

Q805, 855

RY401

R-CH

J803

PHONES

–1

+

L

+

–2

–

+

R

–

TM401

FRONT SPEAKER

IMPEDANCE

USE 6 – 16Ω

+

RESET

(XG100AV)

FAN MOTOR

N

DRIVE

Q961, 962

(Page 22)

M901 (FAN)

M

MUTING CONTROL

RESET

SWITCH

Q801

D807

SWITCH

Q802, 803

MUTING

Q113

R-CH

RESET SIGNAL

GENERATOR

PROTECT

SWITCH

Q804

1

93

6

22

12

27

3

36

4

(Page 20)

R-CH

SL

L

+ +

RY402

POWER AMP

IC101

C

K

OVER LOAD

DETECT

Q101, 181

OVER LOAD

DETECT

Q151

D410

REAR (L-CH) /CENTER

SPEAKER PROTECT

RELAY DRIVE

Q403, 407

REAR (L-CH)

SPEAKER PROTECT

RELAY DRIVE

Q404, 406

RY403

–1

+

L

+

–2

+

–

REAR

+

R

–

+

CENTER

–

TM402

SURROUND

SPEAKER

IMPEDANCE USE 8 – 16Ω

2121

HCD-XG100AV/XG900AV

7-5. BLOCK DIAGRAM – DISPLAY/KEY CONTROL/POWER SUPPLY Section –

(Page 21)(Page 20)

(Page 20)

F

N

E

GRID DRIVE

Q605, 606

FL601

FLUORESCENT INDICATOR TUBE

GRID DRIVE

Q607

S601 – 607, 611 – 619, 621 – 627,

S701 – 710, 712 – 734, 741, 743 – 757

(S632 : XG900AV)

S608

S609

POWER

SAVE/DEMO

(STANDBY)

REMOTE CONTROL

RECEIVER

IC702

S763

(JOG DIAL)

ROTARY

ENCODER

S763

FLUORESCENT INDICATOR TUBE DRIVER,

43

74

75

KEY CONTROL

44 – 46

SEG-1 – SEG-23

28 , 27

GR-15, GR-16

42, 40 – 29

GR-2 – GR-14

GR-1

11 – 15

KEY 0 – KEY 4

4

KEY POWER ON/OFF

KEY POWER

2

SAVE/DEMO

1

SIRCS

JOG A

JOG B

IC601

BPF 0 BPF 1

BPF 2 BPF 3 BPF 4

ALL BAND

GUITAR DISTORTION

RESET

LED SEL

LED DAT LED SCK

LED LATCH

LED STANDBY

I2C DATA

I2C CLK

RECT D832

RECT D831

SUB POWER

TRANSFORMER

T901

POWER

TRANSFORMER

T951

EXCEPT

AEP, UK, Mexican

VOLTAGE

SELECTOR

S901

RY901

POWER ON/OFF

RELAY DRIVE

Q901

AC IN

BAND-PASS FILTER

IC602

17 18 19 20 21

22

73

16

7

5 3 6

67

78 79

16 15 14 13 12

REC LEVEL

11

13 14 15

LED DRIVE

F02 F03 F04 F05 F06

LED DRIVER

IC701

DATA CLK STB

Q601

DET

P1 – P6, P7 – P11, P12 – P16

B.P.F.

17, 19 – 23, 1 – 5, 7 – 11

D601

LINE

REC IN

IN

SPEANA

4

6

B+ SWITCH

Q602, 603

D611 – 614, 621, 622, D700 – 719, 741, 791

30 29

RESET

+5V (LED)

Q604

SYSTEM CONTROLLER

CD MECHANISM

CONTROL

IC501 (5/5)

IIC-DATA

IIC-CLK

DISTORTION

CD-POWER

EVER +5V

SYSTEM CONTROLLER (IC501) ,

FL DRIVER (IC601) B+

TO FLUORESCENT

INDICATOR TUBE

(FL601)

POWER AMP (IC101, 801),

PROTECT CIRCUIT

–35V

CD A+5V (SW) ,

CD D+5V (SW)

CD MECHANISM

DECK SECTION

B+

Q914

+5V (LED)

(PANEL SECTION B+)

D+5V (UNSW)

(RDS SECTION B+)

AU D+5V

M62493FP (IC101),

M62464FP (IC201) B+

D+5V (SW)

(CD SENSOR SECTION B+)

TC, PANEL,

AUDIO

Q906

5

A+7V

A–7V

B+ SWITCH

Q913

FL DRIVER (IC601)

B–

B+ SWITCH

Q911, 912

B+ SWITCH

Q901, 902

B– SWITCH Q903 – 905

REGULATOR

–35V

REGULATOR

Q903, 908

+5V

REGULATOR

IC911

+7V

IC901

–7V

IC951

+5V

IC901

+VL

–VL

+VH

–VH

RECT

D902 – 905

VF

RECT

D841 – 844

RECT

D833 – 836

S736

VOLUME

ROTARY

ENCODER

S736

ST +10V

(FM/AM TUNER UNIT B+)

PL A+10V

M62464FP (IC201) B+

FAN MOTOR B+

TC M+12V

(TC MOTOR SECTION B+)

CD M+7V

(CD MOTOR SECTION B+)

TUNER

B+ SWITCH

Q931, 932

+7V

REGULATOR

IC933

+10V

REGULATOR

IC931

+12V

REGULATOR

IC932

D-SW

8

80

S742

LID (CD)

OPEN/CLOSE

18

WAKE UP

POWER

STBY RELAY

2

43

XOUT

72 70

X601

12.5MHz

WAKE UP

XIN

VOL A

9

10

VOL B

2222

HCD-XG100AV/XG900AV

d

7-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

• : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

Caution: Pattern face side: Parts on the pattern face side seen from (Side B) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Side A) the parts face are indicated.

• Indication of transistor.

C Q

B

E

B

These are omitted.

Q

CE

These are omitted.

Q

CE

These are omitted.

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/ specified.

• 2 : nonflammable resistor.

• 5 : fusible resistor.

• C : panel designation.

Note: The components identified by mark 0 or dotted line

with mark 0 are critical for safety. Replace only with part number specified.

• A : B+ Line.

• B : B– Line.

• H : adjustment for repair.

• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal production tolerances.

• Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F : TUNER (FM/AM) E : TAPE PLAY (DECK A) d : TAPE PLAY (DECK B) G : RECORD J : CD PLAY (ANALOG OUT) c : CD PLAY (DEGITAL OUT) N : MIC INPUT

• Abbreviation AR : Argentina model AUS : Australian model E2 : 120 V AC area in E model EA : Saudi Arabia model MX : Mexican model SP : Singapore model

4

W or less unless otherwise

• Circuit Boards Location

PANEL FL board

PANEL VR board

ILLUMINATION board

TC-A board

MIC board

CD-L board

TC-B board

TRANS board SUB TRANS board

TUNER PACK (FM/AM TUNER UNIT)

SURROUND boar

MAIN board

PA board

HEADPHONES board

CD-R (2) board

CD-R (1) board

FRONT INPUT board

LEAF SW board

TABLE SENSOR board

BD board

CD MOTOR board

AUDIO board

LED board

2323

HCD-XG100AV/XG900AV

7-7. PRINTED WIRING BOARD – BD Board – • See page 23 for Circuit Boards Location.

)(

TP(GND)

21

31

31,,

TP(VC)

TP(RF)

TP(TE)

TP

(AGCCON)

TP(FE)

TP(FE1)

)(

MAIN BOARD

CN411

(Page 34)

19

21

31

31,,

• Semiconductor Location

Ref. No. Location

Q101 C-3

KSS-213DH

• Semiconductor Location

Ref. No. Location

IC101 C-2 IC102 B-1 IC103 B-1

2424

7-8. SCHEMATIC DIAGRAM – BD Board – • See page 35 for Waveforms. • See page 49 for IC Block Diagrams.

HCD-XG100AV/XG900AV

2.2

OPTICAL PICK-UP

BLOCK

(KSS-213DH)

MAIN BOARD

(2/3)

CN411

(Page 32)

D+5V (SW)

L-CH

R-CH

A+5V (SW)

CD-DATA

CD-CLK

SQ-DATA

SQ-CLK

M+7V (UNSW)

• Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD STOP ( ) : CD PLAY

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

2525

HCD-XG100AV/XG900AV

7-9. PRINTED WIRING BOARDS – CD MOTOR Section –• See page 23 for Circuit Boards Location.

B

MAIN BOARD

CN412

(Page 34)

2626

7-10. SCHEMATIC DIAGRAM – CD MOTOR Section –• See page 49 for IC Block Diagram.

HCD-XG100AV/XG900AV

TABLE MOTOR DRIVER

LED DRIVE

4.8

TRAY

(Page 32)

B

MAIN BOARD

(2/3)

CN412

4.8

DISC TABLE SENSOR

2727

4.8

• Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD STOP