Sony HCD-GNZ55D Service Manual

HCD-GNZ55D
SERVICE MANUAL
Ver. 1.1 2006. 10
• HCD-GNZ55D is the tuner, deck, DVD and amplifier section in MHC-GNZ55D.
DVD Section
Tape Deck Section
Model Name Using Similar Mechanism HCD-GNZ7D/GNZ8D/GNZ9D DVD Mechanism Type CDM74HF-DVBU101//C Optical Pick-up Name KHM-310CAB/C2NP
E Model
Amplifier section
The following measured at AC 120, 127, 220, 240 V, 50/60 Hz DIN power output (rated)
40 W + 40 W (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
60 W + 60 W (4 ohms at 1 kHz, 10% THD)
Inputs MIC (phone jack): Sensitivity 1 mV,
impedance 10 kilohms Outputs VIDEO OUT (phono jack):
max. output level
1 Vp-p, unbalanced, Sync
negative load impedance
75 ohms PHONES (stereo mini jack):
Accepts headphones of
8 ohms or more FRONT SPEAKER: Use only the supplied speakers
SPECIFICATIONS
Disc player section
System Compact disc and digital
audio and video system
Laser Semiconductor laser
(DVD: λ=650 nm, CD: λ=790 nm) Emission duration: continuous
Frequency response DVD (PCM 48 kHz):
2 Hz – 22 kHz (±1 dB) CD: 2 Hz – 20 kHz (±0.5 dB)
Video color system format
Latin American model: NTSC Other models: NTSC, PAL
– Continued on next page –
9-887-296-02
2006J04-1 © 2006. 10
DVD DECK RECEIVER
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
1
HCD-GNZ55D
Tape deck section
Recording system 4-track 2-channel stereo Frequency response 50 – 13,000 Hz (±3 dB),
using Sony TYPE I tape
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
(50-kHz step) Antenna FM lead antenna Antenna terminals 75 ohm unbalanced Intermediate frequency 10.7 MHz
AM tuner section
Tuning range Saudi Arabian model: 531 – 1,602 kHz (with the
interval set at 9 kHz) Other models: 531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,710 kHz (with the
interval set at 10 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz
General
Power requirements Saudi Arabian model: 120 – 127 V or 220 – 240 V AC,
50/60 Hz Adjustable with voltage
selector Thai model: 220 V AC, 50/60 Hz Other models: 120 V or 220 – 240 V AC,
50/60 Hz
Adjustable with voltage
selector
Power consumption 45 watts
Dimensions (w/h/d) (Approx.)
280 × 326 × 385.5 mm
Mass (Approx.) 6.4 kg
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-GNZ55D
Ver. 1.1
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of soldering iron around 270°C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky , less prone to flo w) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is claassified as a CLASS 1 LASER product. This label is located on the rear exterior.
NOTE ON REPLACEMENT OF DMB15 BOARD
New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board (A-1167-778-A, etc.) is replaced, exchange new EEPR OM (IC103) with that used before the replacement.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
3
HCD-GNZ55D
MODEL IDENTIFICATION
– BACK PANEL –
PARTS No.
MODEL PARTS No.
E3, E15 models 2-663-832-0s EA model 2-663-832-1s MY, SP models 2-663-832-2s E12, E13 models 2-663-832-3s PH model 2-663-832-5s TH model 2-663-832-6s
• Abbreviation E3 : 240 V AC area in E model E12 : 220-240 V AC area in E model E13 : 220-230 V AC area in E model E15 : Iran model EA : Saudi arabia model PH : Philippine model SP : Singapore model TH : Thai model MY : Malaysia model
4

TABLE OF CONTENTS

HCD-GNZ55D
1. GENERAL
Main Unit ................................................................................ 6
Remote Control ....................................................................... 8
2. DISASSEMBLY
2-1. Cabinet Steel Case............................................................. 10
2-2. Loading Panel.................................................................... 10
2-3. Front Panel Section ........................................................... 11
2-4. DVD Block Section........................................................... 11
2-5. Back Panel Section............................................................ 12
2-6. Main Board, ADC Board .................................................. 12
2-7. Speaker Board, S-Master Board........................................ 13
2-8. Power Unit ........................................................................ 13
2-9. Tape Mechanism Deck ...................................................... 14
2-10. Holder TC-R Assy, Holder TC-L Assy ............................. 14
2-11. Mic Board ......................................................................... 15
2-12. Video Board....................................................................... 15
2-13. DMB15 Board ...................................................................16
2-14. Sensor Board ..................................................................... 16
2-15. Motor (TB) Board ............................................................. 17
2-16. Motor (LD) Board ............................................................. 17
2-17. Pick-Up Unit ..................................................................... 18
2-18. SW Board, Driver Board...................................................18
3. TEST MODE ..................................................................... 19
4. MECHANICAL ADJUSTMENTS............................... 23
5. ELECTRICAL ADJUSTMENTS................................. 24
6. DIAGRAMS
6-1. Block Diagram — RF/Servo Section — ...........................27
6-2. Block Diagram — Video Section — .................................28
6-3. Block Diagram — Main Section —..................................29
6-4. Block Diagram — Audio Section — ................................ 30
6-5. Block Diagram — Function/Power Section —................. 31
6-6. Circuit Boards Location .................................................... 32
6-7. Printed Wiring Boards — Driver Section —..................... 34
6-8. Schematic Diagram — Driver Section —......................... 35
6-9. Printed Wiring Board — DMB15 Section — ................... 36
6-10. Schematic Diagram — DMB15 Section (1/5) — ............. 38
6-11. Schematic Diagram — DMB15 Section (2/5) — ............. 39
6-12. Schematic Diagram — DMB15 Section (3/5) — ............. 40
6-13. Schematic Diagram — DMB15 Section (4/5) — ............. 41
6-14. Schematic Diagram — DMB15 Section (5/5) — ............. 42
6-15. Printed Wiring Board — Main Section — ........................ 43
6-16. Schematic Diagram — Main Section (1/4) — ..................44
6-17. Schematic Diagram — Main Section (2/4) — ..................45
6-18. Schematic Diagram — Main Section (3/4) — ..................46
6-19. Schematic Diagram — Main Section (4/4) — ..................47
6-20. Printed Wiring Board — S-Master Section —.................. 48
6-21. Schematic Diagram — S-Master Section (1/2) —............ 50
6-22. Schematic Diagram — S-Master Section (2/2) —............ 51
6-23. Printed Wiring Board — ADC Section — ........................ 52
6-24. Schematic Diagram — ADC Section —........................... 53
6-25. Printed Wiring Boards — Panel Section — ...................... 54
6-26. Printed Wiring Board — Volume Section — .................... 55
6-27. Schematic Diagram — Panel Section — .......................... 56
6-28. Printed Wiring Board — Mic Section — .......................... 57
6-29. Schematic Diagram — Mic Section —............................. 58
6-30. Printed Wiring Board — Video Section — ....................... 59
6-31. Schematic Diagram — Video Section —..........................60
6-32. Printed Wiring Board — Speaker Section — ................... 61
6-33. Schematic Diagram — Speaker Section — ...................... 62
7. EXPLODED VIEWS
7-1. Main Section ..................................................................... 75
7-2. Front Panel Section (1)...................................................... 76
7-3. Front Panel Section (2)...................................................... 77
7-4. Front Panel Section (3)...................................................... 78
7-5. Chassis Section ................................................................. 79
7-6. DVD Block Section........................................................... 80
7-7. DVD Mechanism Deck Section (1) .................................. 81
7-8. DVD Mechanism Deck Section (2) .................................. 82
8. ELECTRICAL PARTS LIST ........................................ 83
5
HCD-GNZ55D
Illustrati
SECTION 1

GENERAL

List of button locations and reference pages
This section is extracted from instruction manual.
How to use page 104 to 106
Use this page to find the location of buttons and other parts of the unit and remote that are mentioned in the text.
Unit
ALPHABETICAL ORDER
A — D
CD SYNC 8 (61) Deck A wk (60) Deck B qj (60–62, 75) DIRECTION ea (60–62, 73, 75) DISC 1 ~ 3 q; (25, 28, 29) DISC SKIP/EX-CHANGE qa
(18, 23, 25)
Disc tray 7 (18, 19, 23, 26–29,
33–36, 38, 69–71, 86, 87, 91) DISPLAY r; (21, 76, 77) Display 4 (77) DVD eh (18, 19, 21, 24, 25, 61,
62, 67, 72, 76, 88)
E — O
ECHO LEVEL EQ BAND/MEMORY 3 (64) GROOVE qk (63) ILLUMINATION el (58, 77, 90) IR Receptor 2 (17, 85) MASTER VOLUME ql (24, 56,
74, 77, 85) MIC2) (jack) wh (67, 72, 85, 94) MIC 1 MIC 2 MIC LEVEL2) wf (67, 72, 85) MIC 1 LEVEL MIC 2 LEVEL
1)
ws (67)
1)
(jack) wh (67, 72, 85, 94)
1)
(jack) wg (67, 72, 85, 94)
1)
wf (67, 72, 85)
1)
wd (67, 72, 85)
P — Z
PHONES (jack) w; (85, 94) Power illuminator wj (77) PRESET EQ wl (63, 64) REC PAUSE/START 6 (61, 62,
72) SOUND FIELD 5 (65, 83) SUB WOOFER ON/OFF
(67) TAPE A/B ef Tape lid qj wk (60) TUNER/BAND eg (57–59, 76) TUNING +/– qh (57–59) TV/SAT1) ed (62, 76, 84, 86) VIDEO VIDEO INPUT
94)
(60–62, 72, 75, 76)
1)
es (62, 76, 84)
1)
TAPE A/B ef (60–62, 72, 75, 76)
Name of button/part Reference page
3)
ej
(jacks) wa (83,
on number
r
RR
SYMBOLS
?/1 (on/standby) ek (16, 18, 58,
84, 90)
Z OPEN/CLOSE 9 (18, 19, 23,
25, 86)
nN (play) qs (24–27, 31, 33,
35, 36, 38, 48, 51, 60–62, 73, 75, 85, 87)
. OPERATION DIAL >
(go backward/forward) 1 (24, 32, 34, 39, 59, 62, 64, 65)
mM (rewind/fast forward)
qh (24, 60, 88)
qh (25)
X (pause) qd (16) x (stop) qf (61–62, 73, 86, 87,
90)
Z PUSH (Eject A) e; (60) Z PUSH (Eject B) qg (60)
1)
Except for MHC-GNZ55D.
2)
MHC-GNZ55D only.
3)
MHC-GN999D/ MHC-GN999DS only.
6
104
GB
Top view
Front view
34 5 6
2
HCD-GNZ55D
1
r; el ek
ej eh eg
ef ed es
ea e;
wl wk
wj
wh
wg
wf
wd
ws
wa
7 8 9
q; qa qs
qd qf
qg qh
qj qk
ql w;
Additional Information
continued
105
GB
7
HCD-GNZ55D
Remote control
ALPHABETICAL ORDER
A — L
ADVANCE wf (25) ALBUM +/– qa (20, 24) ANGLE q; (44) AUDIO 8 (34, 43, 67, 70, 83) CLEAR wk (20, 27–30, 35, 41, 53) DISC SKIP 3 (25, 28, 29) DISPLAY ed (21, 76, 77) ENTER wh(18–20, 27–31, 34, 36–39, 40, 42, 45–50,
53, 56–59, 68–71, 74–76, 90) FM MODE 7 (59, 89) FUNCTION +/– 4 (19, 24, 57–60, 67, 75, 84, 88) KARAOKE MODE ea (68, 88) KARAOKE PON e; (68) KEY CONTROL #/2 es (69)
M — S
MENU qs (30, 32, 34–36, 39, 57, 58) Numeric Buttons
1)2)
wl (17, 20, 21, 24, 30, 31, 41,
46–50, 59) PICTURE NAVI 6 (35, 36, 41) PRESET + qh (57–59) PRESET – wd (57–59) REPEAT 7 (30) REPLAY wf (25)
3)
5 (72)
SCORE SLEEP eg (20, 74) SLOW qj (25) SLOW ws (25) SOUND FIELD 5
4)
qd3) (65, 83) STEP C wf (25) SUBTITLE 9 (44)
T — Z
THEATRE SYNC 1 (21) TIMER MENU eh (18, 74–76) TIME/TEXT ef (77–79) TOP MENU wj (30) TUNING + qj (57–59) TUNING – ws (57–59)
2)
TV
w; (17)
2)
TV CH + TV CH – TV/VIDEO TV VOL +/– TV &/1 VOLUME +/–
qh (17)
2)
wd (17)
2)
eg (17)
1)2)
qf (17)
(on/standby)2) 2 (17)
1)
qf (24, 56, 74, 77, 85)
NUMBERS AND SYMBOLS
?/1 (on/standby) 2 (16, 18, 74, 75, 85) x (stop) qk (24, 26, 32, 34–36, 39, 45, 58, 60, 75, 86,
87)
X (pause) ql (24, 60)
1)
(play) wa(24–27, 31, 33, 35, 36, 38, 48, 51,
H
60, 75, 85, 87)
> (go forward) qh(21, 24, 32, 34, 39) . (go backward) wd(24, 32, 34, 39) M (fast forward) qj (24, 60, 88) m (rewind) ws (24, 60, 88)
V/v/B/b
10/0
-/--
wh (18, 19, 27–31, 33–42, 45–50, 56, 65,
68–72, 74–76, 90)
2)
wl
2)
wk (17)
O RETURN wg (31, 34, 39, 42)
DISPLAY qg (9, 20, 26–31, 36, 37, 40–42, 45, 47,
49, 56, 68–72, 80, 90)
c STEP wf (25)
1)
The numeric button 5, TV VOL +, VOLUME + and H buttons have a tactile do t. Use th e tactile dot as a reference when operating the system.
2)
This button is used to operate a Sony TV. For details, see “Operating a Sony TV with the remote” on page 17.
3)
MHC-GN999D/MHC-GN999DS/ MHC-GNZ88D/MHC-GNZ77D only.
4)
MHC-GNZ55D only.
eh
eg
ef
ed
es
ea
e;
wl
wk
wj
wh
wg
wf
wd
ws
wa
w;
1
2
3
4
5
6
7
8
9
q;
qa
qs
qd
qf
qg
qh
qj
qk
ql
GB
106
8
Note : Disassemble the unit in the order as shown below.
SET
2-1. CABINET STEEL CASE
(Page 10)
HCD-GNZ55D
SECTION 2

DISASSEMBLY

2-2. LOADING PANEL
(Page 10)
2-3. FRONT PANEL SECTION
(Page 11)
2-4. DVD BLOCK SECTION
(Page 11)
2-5. BACK PANEL SECTION
(Page 12)
2-6. MAIN BOARD, ADC BOARD
(Page 12)
2-7. SPEAKER BOARD,
S-MASTER BOARD (Page 13)
2-9. TAPE MECHANISM DECK
(Page 14)
2-10. HOLDER TC-R ASSY ,
HOLDER TC-L ASSY (Page 14)
2-11. MIC BOARD
(Page 15)
2-12. VIDEO BOARD,
(Page 15)
2-13. DMB15 BOARD
(Page 16)
2-17. PICK-UP UNIT
(Page 18)
2-18. SW BOARD,
DRIVER BOARD (Page 18)
2-8. POWER UNIT
(Page 13)
2-14. SENSOR BOARD
(Page 16)
2-15. MOTOR (TB) BOARD
(Page 17)
2-16. MOTOR (LD) BOARD
(Page 17)
9
HCD-GNZ55D
)
Note : Follow the disassembly procedure in the numerical order given.
2-1. CABINET STEEL CASE
0

cabinet steel case

4
screw (case 3 TP2)
3
screw (case 3 TP2)
8
9
8
6
two screws (+BVTP 3
×
5
three screws (+BVTP 3
7
two screws (+BVTP 3
2
screw (case 3 TP2)
8)
×
8)
×
8
2-2. LOADING PANEL
CD mechanism deck (CDM74)
1
Turn the pulley to the direction of the arrow.
pulley
Front panel side
1
screw (case 3 TP2)
3

loading panel

10
2
Pull-out the disc tray.
2-3. FRONT PANEL SECTION
7
screw (tapping screw)
6
CN503 (3P)
0
5
CN205 (6P)
HCD-GNZ55D
qa

front panel section

four screws (+BVTP 3
9
2-4. DVD BLOCK SECTION
9

DVD block section

4
CN121 (3P)
8
screw
3
CN131 (8P)
1
wire (flat type) (11 core) (CN101)
2
×
8)
wire (flat type) (25 core) (CN201)
5
8
wire (flat type) (13 core) (CN301)
(tapping screw)
2
three
(+BVTP 3
3
screws
×
8)
screw (+BVTP 3
×
8)
6
wire (flat type) (13 core) (CN405)
1
CN1880 (6P)
4
screw (+BVTP 3
7
×
8)
wire (flat type) (17 core) (CN521)
11
HCD-GNZ55D
)
2-5. BACK PANEL SECTION
2
two
(+BVTP 3
1
connector (9 core)
screws
×
8)
7
8

back panel section

3
screw (+BVTP 3
4
two
screws
(+BVTP 3
5
screw (+BVTP 3
6
three
(+BVTP 3
×
8)
×
screws
×
×
8)
8
8)
2-6. MAIN BOARD, ADC BOARD
1
CN501 (8P)
2
wire (flat type) (15 core) (CN500)
3
two
(+BVTT 3
screws
×
6 (sumitite))
8
ADC board
5
6
CN590 (7P)
4
two
(+BVTP 3
7
MAIN board
screws
×
8)
12
2-7. SPEAKER BOARD, S-MASTER BOARD
d
7
two
screws
4
5
two
screws
(+BVTT 3
9
S-MASTER board
CN502 (6P)
×
6 (sumitite))
(+BVTT 3
×
6 (sumitite))
8
heat sink assy
6
two
screws
(+BVTT 3
×
6 (sumitite))
1
CN1501 (4P)
2
two
(+BVTP 3
3
HCD-GNZ55D
screws
×
8)
SPEAKER boar
2-8. POWER UNIT
4
screw (tapping screw)
bracket assy
2
three
(+BVTT 3
3
screws
×
6 (sumitite))
9
bracket (SMPS-B5)
5
three
(+BVTP 3
6
0

power unit

1
screw (tapping screw)
screws
×
8)
7
screw (tapping screw)
8
screw (+BVTP 3
CN1 (2P)
×
8)
13
HCD-GNZ55D
k
r
2-9. TAPE MECHANISM DECK
1
wire (flat type) (11 core)
2
two
screws
(+BVTP 2.6 (3CR))
3
two
(+BVTP 2.6 (3CR))
4
5
tape mechanism dec
screws
two
screws
(+BVTP 2.6 (3CR))
2-10. HOLDER TC-R ASSY, HOLDER TC-L ASSY
6
spring (L)
5
holder TC-L assy
2
damper
1
dampe
14
3
holder TC-R assy
4
spring (R)
2-11. MIC BOARD
4
bracket (TC)
1
four
(+BVTP 2.6 (3CR))
2
bracket (pivot)
5

MIC board

HCD-GNZ55D
screws
2-12. VIDEO BOARD
3
three
(+BVTP 3
screws
×
8)
1
wire (flat type) (5 core) (CN1966)
4
CN401 (5P)
2
two screws (+BVTP 3
×
5

VIDEO board

3
screw (+BVTP 3
8)
×
8)
15
HCD-GNZ55D
)
2-13. DMB15 BOARD
qs
screw (+BVTP 3
9
×
8)
0
screw (+BVTP 3
bracket mediatek
8
screw (+BVTP 3
×
×
qd
cover (CDM)
qa
two
8)
8)
screws
×
(+BVTP 3
2
wire (flat type) (24 core (CN101)
1
CN201 (6P)
8)
2-14. SENSOR BOARD
2
tray
6
two
(+BVTP 3
screws
×
8)
1
floating
(+PTPWH M2.6)
6
floating
(+PTPWH M2.6)
7
gear (geneva)
4
heat sink (MTK IC)
screw
8
screw (+BTTP (M2.6))
screw
9

SENSOR board

0
CN731 (3P)
5
3
two
(+BVTP 3
7

DMB15 board

two
screws
(+BVTP 3
screws
×
3
belt (table)
4
5
×
8)
8)
floating
screw
(+PTPWH M2.6)
pulley (table)
16
2-15. MOTOR (TB) BOARD
table assy
2
stopper
1
2
stopper
6
table motor assy (M741)
HCD-GNZ55D
2-16. MOTOR (LD) BOARD
4
Remove the two solders of motor.
5
loading motor assy (M751)
4
5
3
two
screws
(+BTTP (M2.6))
2
two
(+BTTP (M2.6))

MOTOR (TB) board

Remove the two solders of motor.
screws
3

MOTOR (LD) board

1
belt (loading)
17
HCD-GNZ55D
)
2-17. PICK-UP UNIT
3
two insulator screws
6

pick-up unit

5
two insulators
2
two insulator screws
4
two insulators
2-18. SW BOARD, DRIVER BOARD
7
holder (310)
7
CN702 (5 core)
1
floating
(+PTPWH M2.6
screw
18
2
SW board
1
screw (+BTTP (M2.6))
3
CN704 (2P)
4
CN703 (4P)
5
two
screws
(+BTTP (M2.6))
6
DRIVER board
SECTION 3

TEST MODE

HCD-GNZ55D
[PANEL TEST MODE]
•This mode is used to check the fluorescent indicator tube, LEDs, keys, VOLUME jog, model, destination, software version and VACS level.
Procedure:
1. Press x button, [ILLUMINATION] button and [DISC 2] button
simultaneously.
2. All LEDs and segments in fluorescent indicator tube are lighted
up.
3. When you want to enter to the software version dispaly mode,
press [DISC 1] button. The model information appears on the fluorescent indicator tube. Press [DISC 1] button again to view the destination information.
4. Each time [DISC 1] button is pressed, the display changes from
MC version, SYS version, UI version, DVD version, CDMA version, CDMB version, ST version, TA version, TM version, TC version in this order, and returns to the model ver sion display .
5. When [DISC 3] button is pressed while the version numbers are
being displayed except model and destination, the date of the software creation appears. When [DISC 3] button is pressed again, the display returns to the software version display . When [DISC 1] button is pressed while the date of the software creation is being displayed, the date of the software creation is displayed in the same order of software version display.
6. Press [DISC 2] button, the key check mode is activated.
7. In the key check mode, the fluorescent indicator tube displays
“K 0 V0”. Turn the [OPERATIONAL DIAL] clockwise; “K” value increases by one. Turn the [OPERATIONAL DIAL] counterclockwise; “K” value increases by one. Each time a button is pressed, “K” v alue increases. Press other keys on main unit to check whether the key is detected. However, once a button has been pressed, it is no longer taken into account. “V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if [VOLUME] knob is turned counterclockwise.
8. When [DISC 3] button is pressed after all LEDs and segments in
fluorescent indicator tube light up, the fluorescent indicator tube displays “V A CS A”. A is VACS lev el which is triggered by signal level.
9. When [DISC SKIP/EX-CHANGE] button is pressed after all LEDs
and segments in fluorescent indicator tube light up, alternate segments in fluorescent indicator tube would light up. If you press [DISC SKIP/EX-CHANGE] button again, another half of alternate segments in fluorescent indicator tube would light up. When [DISC SKIP/EX-CHANGE] button is pressed again, all segments lights off. Press [DISC SKIP/EX-CHANGE] button again would cause all segments lights up.
10. To release from this mode, press three buttons in the same
manner as step 1, or disconnect the power cord.
[COMMON TEST MODE]
•This mode is used to check operations of the respective sections of Amplifier and Tape.
Procedure:
•To enter Common Test Mode
1. Press x button, [ILLUMINATION] button and [DISC 3] button
simultaneously.
2. The D VD ring indicators and the line below D VD ring indicator
flash synchronously on the fluorescent indicator tube.
• Check of Amplifier
1. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ MAX” appears on the fluorescent indicator tube. GEQ increases to its maximum.
2. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ MIN” appears on the fluorescent indicator tube. GEQ decreases to its minimum.
3. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ FLAT” appears on the fluorescent indicator tube. GEQ is set to flat.
4. When the [VOLUME] knob is turned clockwise even slightly, the sound volume increases to its maximum and a message “VOLUME MAX” appears on the fluorescent indicator tube.
5. When the [VOLUME] knob is turned counterclockwise even slightly, the sound volume decreases to its minimum and a message “VOLUME MIN” appears on the fluorescent indicator tube.
•Tape function
1. When a tape is inserted in Deck B and recording is started, the function is change to DVD automatically when a tape is inserted in Deck B and recording is started. When [CD SYNC] button is pressed during recording in function, ALC (Automatic Logic Control) is turned on.
2. During recording, press m button will stop the recording and the function is changed to TAPE B and rewind the tape in Deck B until the recording start position and playback of the tape in Deck B is started. If the [REC PAUSE/START] button is pressed for a pause and pressed again to resume recording during recording time, when the tape is rewind, the tape will be rewind until the position where the pause is applied.
•To release from Common Test mode
1. To release from this mode, press
2. The cold reset is enforced at the same time.
[COLD RESET]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the set to the customer.
Procedure:
1. Press ?/1 button to turn on the system.
2. Press x button, [ILLUMINATION] button, and ?/1 button simultaneously.
3. The message “COLD RESET” appears on the fluorescent indicator tube. Then, the fluorescent indicator tube becomes blank for a while, and the system is reset.
[VACS ON/OFF]
•This mode is used to switch on and off the VACS (Variable
Attenuation Control System).
Procedure:
1. Press ?/1 button to turn on the system.
2. Press x button, [DIRECTION] button and [DISC 1] simultaneously. The message “VACS OFF” or “VACS ON” appears on the fluorescent indicator tube.
[TUNER STEP CHANGE]
•The step interval of AM c hannels can be toggled between 9 kHz
and 10 kHz. This mode is not available for Saudi Arabia and Russia models.
?/1 button.
19
HCD-GNZ55D
Procedure:
1. Press ?/1 button to turn on the system.
2. Press [TUNER/BAND] button repeatedly to select the “AM”.
3. Press
4. Press [ILLUMINATION] button and
[DVD SHIP MODE (WITH MEMORY CLEAR)]
•This mode moves the optical pick-up to the position durable to
Procedure:
1. Press ?/1 button to turn on the system.
2. Select DVD function.
3. Press x button, [DIRECTION] button and ?/1 button
4. After the “STANDBY” blinking display finishes, a message
[DVD SHIP MODE (WITHOUT MEMORY CLEAR)]
•This mode moves the optical pick-up to the position durable to
?/1 button to turn off the system.
?/1 button simultaneously.
The system will turn on automatically. The message “AM 9K STEP” or “AM 10K STEP” appears on the fluorescent indicator tube and thus the channel step is changed.
vibration and clears all data including preset data stored in the RAM to initial conditions. Use this mode when returning the set to the customer after repair.
simultaneously during “DVD NO DISC” condition. The system will turn off automatically.
“MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set.
vibration. Use this mode when returning the set to the customer after repair.
[DVD COLOR SYSTEM]
• This mode let you change the color system of the video output from P AL to NTSC or vice-versa. This mode is not av ailable for Latin American and Russian models.
Procedure:
1. Press
2. Select DVD function.
3. Press ?/1 button again to turn off the system.
4. Press X button and ?/1 button simultaneously. The system
[REMOTE DISABLE MODE]
• This mode let you disable the remote commander reception.
Procedure:
1. Press ?/1 button to turn on the system.
2. Press x button, [DIRECTION] button and [DISC 3] button
?/1 button to turn on the system.
will turn on automatically. The message “COLOR PAL” or “COLOR NTSC” appears on the fluorescent indicator tube.
When this mode is activated, the system will not response if the button on the remote commander is pressed. The message “RM DISABLE” appears on the fluorescent indicator tube. This mode is essential for conducting test and repairing when no interruption from the other remote commander is expected. This mode is cancelled automatically when the system is turned off.
simultaneously until “SIRCS ON” or “SIRCS OFF” appears on the fluorescent indicator tube.
Procedure:
1. Press ?/1 button to turn on the system.
2. Select DVD function.
3. Press [DVD] button and NO DISC” condition. The system will turn off automatically.
4. After the “STANDBY” blinking display finishes, a message “MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set.
[DVD TRAY LOCK MODE]
•This mode let you lock the disc tray. When this mode is
activated, the disc tray will not open when [OPEN/CLOSE] button or [DISC SKIP/EX-CHANGE] button is pressed. The message “LOCKED” will appears on the fluorescent indicator tube.
Procedure:
1. Press ?/1 button to turn on the system.
2. Select DVD function.
3. Press x button and [OPEN/CLOSE] button simultaneously and hold down until “LOCKED” or “UNLOCKED” appears on the fluorescent indicator tube (around 5 seconds).
[TCM OFFLINE MODE]
•This mode prevents the system from turning off automatically
when TCM is not connected. Therefore, measurements can be done even when TCM is not connected during production.
?/1 button simultaneously during “DVD
[MTK FIRMWARE DISPLAY]
•This mode is used to display the MTK firmware version.
Procedure:
1. Press
2. Press [DVD] button to switch to DVD function.
3. Press ?/1 button again to turn off the system.
4. Press x button and ?/1 button. The system turns on
5. The version of MTK firmware appears on the TV screen.
[DVD SERVICE MODE]
•This mode let you make diagnosis and adjustment easily by
?/1 button to turn on the system.
automatically.
using the remote commander and the TV. The instructions, diagnostic results, etc. are given on the on-screen display.
Procedure:
1. When the system is turned off, press [EQ BAND/MEMORY] button, [TAPE A/B] button and ?/1 button simultaneously. The system will turn on automatically.
2. The message “TCM OFFLINE” will appears on the fluorescent indicator tube.
•To release from TCM Offline Mode
To release from this mode, perform “COLD RESET” or turn off the power supply.
20
HCD-GNZ55D
• TEST DISC LIST
Be sure to use the DVD disc that matches the signal standards of your region.
• CD YEDS-18 (Part No.: 3-702-101-01) PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer)
NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL:HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Dual Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL:HLX-507 (Part No.: J-6090-078-A)
• Procedure to enter to DVD Service Mode:
1. Press ?/1 button to turn on the system.
2. Select DVD function.
3. Press x button and [OPEN/CLOSE] button simultaneously and
then turn the [VOLUME] knob clockwise.
4. The message “SERVICE IN” appears on the fluorescent
indicator tube and the Top Menu of Remocon Diagnosis Menu appears on the on-screen display on the TV. The model name and revision number is displayed at the bottom of the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name : GML6DS_ME IF-con : V Syscon : Ver.
er. 01.00 (0000)
0.302
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press ?/1 button to turn off the
system.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
O o Change Value RETURN Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote commander .
4. Wait until a hexadecimal number appears in the on-screen display as below:
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
O o Change Value RETURN Return to previous menu
5. Con vert data from hexadecimal to decimal by using con version table.
6. Press [RETURN] button on the remote commander to return to previous menu.
7. Press [0] button on the remote commander to return to the Top Menu of Remocon Diagnosis Menu.
8. Press ?/1 button to turn off the system.
• Execute IOP Measurement
In order to execute mirror time adjustment, the following standard procedures must be followed.
1. From the Top Menu of Remocon Diagnosis Menu, select “2. Drive Manual Operation” by pressing the [2] button on the remote commander. The following screen appears on the on­screen display.
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test Mode
5. MIRR time Adjust
0. Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display.
• Check Emergency History
To check the emergency history, please follow the following procedure.
1. From the Top Menu of Remocon Diagnosis Menu, select “3. Emergency History” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display.
Emg.History Check
Laser Hours CD 999h 59min
1. 01 05 04 04 00 00 00 00 00 00 23 45
2. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45
Next Next Page Prev Prev Page
O Return to Top Menu
DVD 999h 59min
00 92 46 00
21
HCD-GNZ55D
2. You can check the total time when the laser is turned on during playback of DVD and CD from the above menu. The maximum time, which can be displayed are 999h 59min.
3. You can check the error code of latest 10 emergency history from the above menu. To view the previous or next page of emergency history, press . or > on the remote commander. The error code consists of
• Error Code
Example of Error code
1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45
The meaning of error code is as below:
01: Communication error (No reply from syscon) 02: Syscon hung up 03: Power OFF request when syscon hung up 19: Thermal shutdown 24: MoveSledHome error 25: Mechanical move error (5 Changer) 26: Mechanical move stack error 30: DC motor adjustment error 31: DPD offset adjustment error 32: TE balance adjustment error 33: TE sensor adjustment error 34: TE loop gain adjustment error 35: FE loop gain adjustment error 36: Bad jitter after adjustment 40: Focus NG 42: Focus layer jump NG 52: Open kick spindle error 51: Spindle stop error 60: Focus on error 61: Seek fail error 62: Read Q data/ID error 70: Lead in data read fail 71: TOC read time out (CD) 80: Can’t buffering 81: Unknown media type
• Parameter of error code
This is the detail of error code.
To clear the Laser Hour
Press [DISPLAY] button and then press [CLEAR] button. The data for both CD and DVD data are reset.
Emg.History Check
Laser Hours CD 0h 0min
1. 01 05 04 04 00 00 00 00 00 00 23 45
2. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45
Next Next Page Prev Prev Page
O Return to Top Menu
DVD 0h 0min
00 92 46 00
To clear the Emergency History
Press [MENU] button and then press [CLEAR] button. T he error code for all emergency history would be reset.
Emg.History Check
Laser Hours CD 999h 59min
1. 00 00 00 00 00 00 00 00 00 00 00 00
2. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Next Next Page Prev Prev Page
O Return to Top Menu
DVD 999h 59min
00 00 00 00
To return to the Top Menu of Remocon Diagnosis Menu
Press [0] button on the remote commander.
• Check Version Information
To check the version information, please follow the following procedure.
1. From the Top Menu of Remocon Diagnosis Menu, select “4. Version Information” by pressing the [4] button on the remote commander. The following screen appears on the on-screen display.
Example of Error code
1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45
•Time of error code
This is the laser time when an error occurred.
Example of Error code
1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45
22
Version information
Firm (Main) : Ver. xxxxx Firm (Sub) : xxxxx RISC : xxxxx 8032 : xxxxx Audio DSP : xxxxx Servo DSP : xxxxx
O Return to Top Menu
To return to the Top Menu of Remocon Diagnosis Menu, press [0] on the remote commander.
SECTION 4

MECHANICAL ADJUSTMENTS

Precaution
1. Clean the following parts with a denatured alcohol-moistened swab:
record/playback heads pinch rollers erase head rubber belts capstan idlers
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
Torque Measurement
Mode
FWD
FWD back tension
REV
REV back tension
FF/REW
FWD tension
REV tension
Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
3.06 N • m to 6.96 N • m 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m 71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m
100 g or more
(3.53 oz or more)
9.80 N • m
100 g or more
(3.53 oz or more)
HCD-GNZ55D
23
HCD-GNZ55D
)
SECTION 5

ELECTRICAL ADJUSTMENTS

DVD SECTION
When the base unit is replaced, perform the adjustment and the measurement as shown below in this order.
1) MIRROR TIME ADJUSTMENT (See page 22)
2) EXECUTING IOP MEASUREMENT (See page 24)
[TEST DISC LIST]
Be sure to use the DVD disc that matches the signal standards of your region.
• CD YEDS-18 (Part No.: 3-702-101-01) PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer)
NTSC :HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL : HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Dual Layer)
NTSC :HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL : HLX-507 (Part No.: J-6090-078-A)
[RFMON Level Check]
Connection:
oscilloscope
DMB15 board
CN105 pin 6 (RFMON)
CN105 pin
3
(GND)
+ –
Checking Location: DMB15 board (Side A)
IC101
IC102
(SIDE A)
IC104
CN105
IC201
6
1
CN105 pin 3 (GND
DMB15 BOARD
CN106
CN105 pin 6 (RFMON)
VIDEO SECTION
Video Level Check (VIDEO BOARD)
Purpose
This adjustment is made to satisfy the NTSC standard, and if not adjusted correctly, the brightness will be too large or small.
Procedure:
1. Connect an oscilloscope to CN105 pin 6 (RFMON) and CN105 pin 3 (GND) on the DMB15 board.
2. Turn the power on.
3. Set the test disc (refer to the TEST DISC LIST) on the tray and press H button to playback.
4. Confirm that oscilloscope waveform is clear and check RFMON signal level is correct or not.
Note: A clear RFMON signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
RFMON signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level: 0.58 ± 1.23 Vp-p (DVD)
0.57 ± 1.1 Vp-p (CD)
oscilloscope
75
set
J1902 VIDEO OUTPUT
Procedure:
1. Connect oscilloscope to VIDEO output.
2. Load a DVD reference disc playback.
3. Check the video signal level is 1.00±0.07Vp-p.
(WHITE 100%)
1.00 ± 0.07 Vp-p
24
HCD-GNZ55D
r
e
DECK SECTION
0 dB=0.775 V
1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the parts adjust.
4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
5. The adjustments should be performed in the order giv en in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)
6. The adjustments should be performed for both L-CH and R­CH.
7. Switches and controls should be set as follows unless otherwise specified.
•Test Tape
Tape Signal Used for
P-4-A063 6.3 kHz, –10 dB Azimuth Adjustment
Record/Playback Head Azimuth Adjustment
DECK A DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback
3. Mode: Playback
test tape P-4-A063 (6.3 kHz, –10 dB)
L-CH
MAIN board IC101
R-CH
waveform of oscilloscope
in phase 45°90°135°180
pin 28
pin 36
L R
pin 37
good
oscilloscop
V
wrong
H
°
4. After the adjustments, apply suitable locking compound to the pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
test tape P-4-A063 (6.3 kHz, –10 dB)
MAIN board IC101 Pin 28 (L-CH) Pin 37 (R-CH)
set
MAIN board IC101 Pin 36 (GND)
level mete
+
2. T urn the adjustment screw and chec k output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
output level
within 1dB
L-CH peak
R-CH peak
within 1dB
screw position
L-CH peak
screw position
R-CH peak
forward
reverse
25
HCD-GNZ55D
MEMO
26
SECTION 6 DIAGRAMS
6-1. BLOCK DIAGRAM — RF/SERVO SECTION —
HCD-GNZ55D
DETECTOR
OPTICAL PICK-UP
BLOCK
LIMIT
LASER
CD LD
DIODE
(FOR CD)
LASER
DVD LD
DIODE
(FOR DVD)
VR650
VR780
RF
A B C D
F
E
D
CBA
DVDRFIP
6
2
DVDA
3
DVDB
4
DVDC
5
DVDD
19
TPI
18
TNI
A
8
NA
B
9
NB
C
10
MC
D
11
MD
OSP
252 253
OSN
CD/DVD RF AMP,
FOCUS/TRACKING ERROR AMP
DVD SYSTEM PROCESSOR
DIGITAL SERVO PROCESSOR
IC102(1/2)
• Signal Path
: CD PLAY
176
LI M SW
AUTOMATIC POWER CONTROL (FOR CD)
Q102 (1/2)
PD
AUTOMATIC POWER
CONTROL (FOR DVD)
Q102 (2/2)
VOLUME CONTROL
Q101, Q103
23
LD01
110
20
MD12 MD11
21
LD02
22
MSW
50
PRST
IFCK
IFSDO
IFSDI
XIFCS
99
98 101 100
26
33
32 31 27
: DVD PLAY
: SACD PLAY
MTK_RESET
MTK_CLK
MTK_SOD
MTK_SIO MTK_XIFCK
2AXIS DEVICE FOCUS/
TRACKING
COIL
SLED
SPINDLE
MSW
FCS+ FCS–
TRK+ TRK–
VCC
SL– SL+
MM
SP+ SP–
MM
FOCUS/TRACKING COIL DRIVER, SPINDLE, SLED MOTOR DRIVER
42 41
36 48 37 1
35 3 34 4
32
30 29
27 28
46 47
IC201
BUFFER
FOCUS COIL
DRIVE
TRACKING COIL
DRIVE
SLED MOTOR
DRIVE
SPINDLE MOTOR
DRIVE
BUFFER
105
IFBSY
43
10 13
40
45
19 20 22 21
V1P4
FOO
TRO
FMO
DMO
V1P4
FMO FOO
DMO TRO
38 42
37 41
30
40
47
211 210 170
FMO FOO
DMO TRO
V REFO
IOPMON
SPFG
MUTE123 MUTE TSDM
KRMOD/HSYNC
MIC/VSYNC
207
205
28
MTK BUSY
24
KRMOD
25
MIC STATUS
SYSTEM
CONTROL
IC401(1/4)
HCD-GNZ55D
27 27
HCD-GNZ55D
6-2. BLOCK DIAGRAM — VIDEO SECTION —
YUV3
ASDAT0 ASDAT1 ASDAT2 ASDAT4
XRST ACLK ABCK
ALRCK
198
V
MAIN
A
SECTION
(Page 29)
D/A CONVERTER
IC301
217 218 219 222
220 215 214 213
14
SDTI1
15
SDTI2
16
SDTI3
13
SDTI4
8
PDN
10
MCLK
9
BICK
17
LRCK
(DMIXL)
(FL)
LOUT4+ LOUT4–
LOUT1+ LOUT1–
38 37
2 1
IC3771
IC3711
DOWNMIX L
FRONT L
B
(Page 29)
MAIN
SECTION
• Signal Path
19
SCL
20
SDA
: AUDIO
: VIDEO
: DIGITAL
X101
27MHz
DIGITAL
225
SDPIF
229
XTALI
XTALO
228
SCL
SDA
102
103
6 5
SCL
SDA
EEPROM
IC103
OPTICAL
TRANSMITTER
IC508
DVD SYSTEM PROCESSOR
IC102(2/2)
HD0 – HD7 A0 – A21
HD0 – HD7
29,31,33,35,38,40,42,44 25-16, 10 -1, 48
DQ0 – DQ7
DVD
DIGITAL
OUT
AD0 – AD7
81-84,86-88,91
DATA & ADDRESS BUS
DATA & ADDRESS BUS
HIGHA0-7 IOA0-7, IOA18-IOA21 A16, A17
53-61, 67-72, 74-76,
78, 89, 92, 93
A0
A0 – A19DQ15/A-1
FLASH ROM
IC101
A1-A21
IOCS
IOWA
IOUE
77
79
66
CEWEOE
2,4,5,7,8,10,11,13,42,44,45,47,48,50,51,53
CE
OE
WE
2645
28OE11
CE
WE
RD0 – RD15
125-123, 121, 120, 118,
117, 115, 135, 133-128, 126
RD0 – RD15
RA0 – RA11
146, 147, 149-151,
158-160, 162, 164-166
22-26,
29-35
RA0 – RA11
SDRAM
IC104
RCLK
RCS
RWE
RAS
BA0
BA1
143
20
142
145 156 113 137 157
38
19
21
BS0
BS1
DRCLK
138
RCS
CAS
140
139
16
18
17
CAS
RAS
RWE
15
DQM0
39
DQM0
DQM1
37
DQM1
CKE
DRCKE
HCD-GNZ55D
2828
6-3. BLOCK DIAGRAM — MAIN SECTION —
HCD-GNZ55D
ANTENNA
J1400
MIC
HRPE901
FM 75
COAXIAL
AM
(DECK A)
HP901
PB
HEAD
(DECK B)
REC/PB
HEAD
ERASE
HEAD
TAPE
MECHANISM
DECK
BLOCK
B SHUT A SHUT
A HALF B HALF
REC(REV)
REC(FWD)
CAP M+
B TRGM+
A TRGM+
TU901
R-CH
R-CH
Q154,
155
R-CH
VIDEO
B
SECTION
(Page 28)
5LCH 3RCH
R–CH
4+9V
ST A+9V
DIN
8DO
DOUT
6DI
CLK
7CL
CE
9CE
TUNED
1TUNED
MIC AMP
IC1401 (1/2)
RV1400
MIC
LEVLE
T101
MUTE CONTROL
Q107–109
FRONT L
DOWNMIX L
Q113,114
BIAS OSC
Q112
CAP CONTROL
Q120,121
B TRG CONTROL
Q118,119
A TRG CONTROL
Q122,123
MIC AMP
IC1401 (2/2)
BIAS+9V
MUTE
Q166
MUTE CONTROL
Q110,111
AUDIO
SECTION
(Page 30)
MUTE
MUTE
Q238
MUTE CONTROL
Q301,302
C
Q237
MUTE
Q175
NSP MUTE
SOFT MUTE
DVD/CD MUTE
INIT
CONTROL Q307,308
REC/PB AMP,
SOUND CONTROL
IC101
57 FRONT
4
DVD/CD
TU–LCH
3
59
MIC
75
PB A
76
PB B
17
REC
34
CLK
35
DATA
37
DIN
39
DOUT
38
CLK 36 40
34
83 84
23
90 89 63 91
20 21 18 19 17
12
10
ST CE TUNED
DVD A MUTE
DATA CLK
MIC DETECT
B SHUT A SHUT A HALF B HALF
SIGNAL IN/OUT CONTROL
7
REC MUTE REC BIAS TC REALY CAMP CNT B TRIG A TRIG
SM INIT
9
SM NSP MUTING
SM SOFT MUTING
SYSTEM
CONTROL
IC401 (3/4)
IC403
28FRONT L 37FRONT R
R–CH
26F/B
53L+R LIGHTING
DBFB
FEED BACK
Q101
88VACS IN
66IO EXP DATA OUT 68IO EXP RST 69IO EXP CLK 70IO EXP LAT
DATA
RST CLK LAT
VIDEO
SECTION
A
V
(Page 28)
21VIDEO MUTE
22ADC RESET
RST
2RESET
CLK
3CLK
LAT
4LATCH
DATA
26D1
FRONT L
ADC RESET
DBFB FEED BACK
VIDEO SIGNAL SELECT
IC1800
OUT
IN
4
SAG
PC
1
J506
D–LIGHT
SYNC OUT
2 3
AUDIO
D
SECTION
(Page 30)
• Signal Path
: AUDIO
: TUNER
: PB (DECK A)
: PB (DECK B)
: REC (DECK B)
: VIDEO
• R-CH is omitted due to same as L-CH.
J1900 VIDEO
OUT
HCD-GNZ55D
29 29
HCD-GNZ55D
6-4. BLOCK DIAGRAM — AUDIO SECTION —
MAIN
SECTION
(Page 29)
MAIN
SECTION
(Page 29)
D
C
DBFB FEED BACK
FRONT L
ADC RESET
X1
12.288MHz
NSP MUTE
SOFT MUTE
INIT
• Signal path : AUDIO : DIGITAL
M751
(LOADING)
M741
(TABLE)
OPEN/CLOSE
RE701 DISC TRAY ADDRESS
DETECT
ADDRESS
SENSOR
SERIAL CLOCK
S751
DETECT
IC731
TABLE
M
M
R-CH
BUFFER
IC3
CLOSE OPEN
LOADING
4
MOTOR
2
4
MOTOR
2
Q731
IC701
DRIVE
IC712
TABLE
DRIVE
A/D CONVERTER
L IN
1 2
R IN
7
PDWN
15
SCKI
7 9
7 9
IC11
41
43 44 45
42
48 49
46 47
D OUT
12
10
LRCK
BCK
11
SYSTEM CONTROL
IC401(2/4)
OPEN SWITCH
E–3 E–2 E–1
TABLE SENSE
LM–F LM–R
TM–F TM–R
SM LATCH1
SM CLK
SM DATA
SM RESET
SM SD
HP MUTE
HP DET
D/A CONVERTER
IC600
31
DATA
HP AMP
4 6
PWM A PWM B
X801
49MHz
IC880
AMP
IC630
OUT A
OUT B
OUT C
OUT D
RESET AB
RESET CD
/SD
MUTE
Q1400,1401
MUTE CONTROL
Q486
33
30
25 22
3 5
15
R-CH R-CH
DC DETECT
Q840
DC DETECT
Q860,861
29
LRCK
30
BCK
36
XFSIIN
18
NSPMUTE
19
SOFTMUTE
27
INIT
23
SCLATCH
22
SCSHIFT
21
SCDT
76 77 78 65 72
86 85
HPOUTL1
HPOUTL2
HPOUTR1 HPOUTR2
OUTL1 OUTL2
XFSOOUT
45 43
R-CH
41
R-CH
39
11
9
SERIAL CLOCK
48
BUFFER
IC802
D486
R-CH
UNREG+8V
R-CH R-CH
TM1500
J1401
PHONES
L
R
FRONT
SPEAKER
HCD-GNZ55D
3030
Loading...
+ 70 hidden pages