Sony HCD-BX3, HCD-DX3 Service manual

HCD-BX3/DX3
Ver 1.0 2000.1
• HCD-BX3/DX3 is the tuner, deck, CD and amplifier section in MHC­BX3/DX3.
Photo: HCD-BX3
CD CD Mechanism Type CDM58-K2BD38 Section Base Unit Name BU-K2BD38
Tape deck Model Name Using Similar Mechanism NEW Section T ape Transport Mechanism T ype TCM-230MWR11
US Model
Canadian Model
AEP Model
UK Model
HCD-BX3
E Model
Australian Model
HCD-DX3
Model Name Using Similar Mechanism NEW
Optical Pick-up Name KSM-213DAP
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS: (HCD-BX3 US model only)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 6 ohm loads both channels driven, from 120-10,000 Hz; rates 75 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output.
Amplifier section US, Canadian model: HCD-BX3:
Continuous RMS power output (reference)
60 + 60 watts (6 ohms at 1 kHz, 10% THD)
Total harmonic distortion less than 0.07%
(6 ohms at 1 kHz, 35 W)
AEP, UK model: HCD-BX3:
DIN power output (rated) 45 + 45 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
60 + 60 watts (6 ohms at 1 kHz, 10% THD)
Music power output (reference)
150 + 150 watts (6 ohms at 1 kHz, 10% THD)
Other model: HCD-DX3:
The following measured at AC 120, 220, 240 V 50/60 Hz
DIN power output (rated) 75 + 75 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
100 + 100 watts
(6 ohms at 1 kHz, 10% THD) Inputs MD/VIDEO IN: voltage 450/250 mV, (phono jacks) impedance 47 kilohms MIC: sensitivity 1 mV, (mini jack) impedance 10 kilohms
Outputs PHONES: accepts headphones of (stereo mini jack) 8 ohms or more SPEAKER: accepts impedance of 6 to 16 ohms
CD player section
System Compact disc and digital audio system Laser Semiconductor laser (λ=780 nm)
Emission duration: continuous Laser output Max. 44.6 µW*
*This output is the value measured at a
distance of 200 mm from the objective
lens surface on the Optical Pick-up Block
with 7 mm aperture.
— Continued on next page —
COMPACT DISC DECK RECEIVER
MICROFILM
Wavelength 780 – 790 nm Frequency response 2 Hz – 20 kHz (±0.5 dB) Signal-to-noise ratio More than 90 dB Dynamic range More than 90 dB CD OPTICAL DIGITAL OUT (Square optical connector jack, rear panel) Wavelength 660 nm Output Level –18 dBm
Tape player section
Recording system 4-track 2-channel stereo Frequency response 40 – 13,000 Hz (±3 dB), using Sony TYPE I
cassette
Mass US model: HCD-BX3: Approx. 7.8 kg Canadian model: HCD-BX3: Approx. 7.8 kg AEP model: HCD-BX3: Approx. 7.9 kg Other models: HCD-DX3: Approx. 8.9 kg
Design and specifications are subject to change without notice.
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz Antenna FM lead antenna Antenna terminals 75 ohm unbalanced Intermediate frequency 10.7 MHz
AM tuner section
Tuning range US, Canadian, Mexican, Argentina models:
530 – 1,710 kHz (with the interval set at 10 kHz) 531 – 1,710 kHz (with the interval set at 9 kHz)
AEP, Saudi Arabia models:
531 – 1,602 kHz (with the interval set at 9 kHz)
Other models: 531 – 1,602 kHz
(with the interval set at 9 kHz) 530 – 1,710 kHz
(with the interval set at 10 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz
General
Power requirements US, Canadian models: 120 V AC, 60 Hz AEP model: 230 V AC, 50/60 Hz Australian model: 230-240 V AC, 50/60 Hz Mexican model: 120 V AC, 50/60 Hz Other models: 120 V, 220 V or 230 - 240 V AC, 50/60 Hz
Adjustable with voltage selector
Power consumption US model: HCD-BX3: 140 watts Canadian model: HCD-BX3: 130 watts AEP model: HCD-BX3: 130 watts Other models: HCD-DX3: 170 watts
SAFETY CHECK-OUT
(US model only)
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for A C leakage. Check leakage as described below.
LEAKAGE
The A C leakag e from any exposed metal part to earth g round and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT -540A. Follo w the manufacturers’ instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated A C voltmeter . The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are e xamples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
AC
0.15µF
1.5k
voltmeter (0.75V)
Dimensions (w/h/d) HCD-BX3/DX3: Approx. 280 x 325 x 403 mm
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage .
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

TABLE OF CONTENTS

1. SERVICE NOTE······························································· 4
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Notes on chip component replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
2. GENERAL ·········································································· 5
3. DISASSEMBY ·································································· 7
4. TEST MODE ···································································· 12
5. MECHANICAL ADJUSTMENTS ····························· 16
6. ELECTRICAL ADJUSTMENTS ······························· 16
7. DIAGRAMS
7-1. Circuit Board Location ················································· 21 7-2. Block Diagrams ···························································· 22 7-3. Printed Wiring Board BD Section ···························· 24 7-4. Schematic Diagram BD Section ······························· 25 7-5. Printed Wiring Board Main Section ························· 26 7-6. Schematic Diagram Main Section (1/3) ··················· 27 7-7. Schematic Diagram Main Section (2/3) ··················· 28 7-8. Schematic Diagram Main Section (3/3) ··················· 29 7-9. Printed Wiring Board AMP Section ························· 30 7-10. Schematic Diagram AMP Section ·························· 31 7-11. Printed Wiring Board Panel Section ······················· 32 7-12. Schematic Diagram Panel Section ·························· 33 7-13. Printed Wiring Board Leaf SW Section·················· 34 7-14. Schematic Diagram Leaf SW Section ···················· 35 7-15. Printed Wiring Board Driver Section······················ 36 7-16. Schematic Diagram Driver Section ························ 37 7-17. Printed Wiring Board Trans Section ······················· 38 7-18. Schematic Diagram Trans Section··························39 7-19. IC Pin Function Description ······································· 40 7-20. IC Block Diagrams ····················································· 42
8. EXPLODED VIEWS
8-1. Main Section ································································· 45 8-2. Panel Section ································································ 46 8-3. Main Board Section ······················································ 47 8-4. Tape Mechanism Section·············································· 48 8-5. CD Mechanism Section ················································ 49
9. ELECTRICAL PARTS LIST ······································· 50
MODEL IDENTIFICATION
BACK PANEL —
PARTS No.
Flexible Circuit Board Repairing
Keep the temperature of soldering iron around 270˚C during repairing.
Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering or unsoldering.
MODEL
BX3: AEP, UK, G, AED models DX3: AR, E, EA, SP, TW, MY models BX3: US, CND models DX3: AUS, KR, MX, TH models BX3: CIS model
Abbreviation CND : Canadian model AUS : Australian model G : German model AED : North European model EA : Saudi Arabia model MY : Malaysia model
PARTS No.
4-224-547-0s 4-224-547-1s 4-224-547-2s 4-224-547-4s 4-226-245-0s
SP : Singapore model TH : Thai model TW : Taiwan model KR : Korea model MX : Mexican model AR : Argentina model
3
SECTION 1
SERVICE NOTE
2
Panel board
Note for installing the panel board
1
Cut the fourteen melted-connection points with a cutting plier.
Screw hole
Attach the panel board with fourteen screws ( after the board is removed once. Do not tighten the screws excessively.
+BVTP 2.6 × 8
)
Hot melt
4
123 45
SECTION 2
GENERAL
wa
w;
ql
qk
qj
qsqdqfqgqh
1 – . button 2 x button 3 gG button 4 S button 5 > + button 6 PLAY MODE button 7 REPLAY button 8 EDIT button 9 VOLUME knob q; PHONE jack qa OPEN/CLOSE button qs DISC 3 button qd DISC 2 button qf DISC 1 button qg DISC SKIP EX-CHANGE button qh CURSOL button qj MIC jack qk MIC LEVEL knob ql SPECTRUM button w; DISPLAY button wa @/1 button
qa
6
7
wd
8
ws
9
q;
Photo: HCD-BX3
ws MD/VIDEO button and indicator wd TAPE A/B button and indicator wf CD button and indicator wg TUNER/BAND button and indicator wh CROOVE button and indicator wj SURROUND button and indicator wk CD SYNC HI-DUB button wl REC PAUSE/START button and indicator e; KARAOKE PON b utton ea ENTER button es EQ EDIT button
es
wf
wg
wh
wj
wk
e;ea
wl
5
6
1
3,5
2,4
To attach the front speaker pads
Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the
speakers and prevent them from slipping.
Inserting two size AA (R6)
batteries into the remote
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates
the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of
time, remove the batteries to prevent possible
damage from battery leakage.
When carrying this system
Make sure that all discs are removed from the
unit. To protect the CD mechanism, hold
down CD and press ?/1 while the power is
on. “LOCK” appears in the display and the
power is turned off.
E
e
e
E
1
Press CLOCK/TIMER SET.
The hour indication flashes.
Step 1: Hooking up the system
(continued)
l
hH
Ss
jJ
L
HS s
Step 2: Setting the
time
You must set the time before using the timer
functions.
The clock uses a 24-hour system on the
European model, and a 12-hour system on
other models.
The 24-hour system is used for illustration
purposes.
7
23
41
?/1
(Power)
continued
Shuttle
Step 3: Presetting
radio stations
You can preset a total of 30 preset stations (20
for FM and 10 for AM).
2
Press . or > repeatedly to set
the hour.
3
Press ENTER.
The minute indication flashes.
4
Press . or > repeatedly to set
the minute.
5
Press ENTER.
The clock starts working.
Tip
If you make a mistake, start over from step 1.
To change the time
The previous explanation shows how to set
the time while the power is off. To change the
time while the power is on, do the following:
1 Press CLOCK/TIMER SET.
2 Press . or > repeatedly to select SET
CLOCK.
3 Press ENTER.
4 Perform steps 2 through 5 above.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
This section is extracted from instruction manual.
6
SECTION 3
s
DISASSEMBY
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER CASE (TOP)
5
Two screws (Case)
Case (L)
6
Screw (Case)
Upper case (Top)
7
Two screws
(+BVTP 3
×
8
10)
q;
9
Two screws (+BVTP 3
4
×
10)
Case (R)
3-2. LOADING PANEL ASSY
CD mechanism deck (CDM58) 1
Turn the pulley to the direction of arrow.
pulley
Front panel side
2
Pull-out the disc tray.
Loading panel assy
3
1
2
Screw (Case)
3
Two screw
Two screws (Case)
7
3-3. FRONT PANEL SECTION
CD mechanism deck (CDM58)
4
Screw (+BVTP 3
2
3
Connector (CN303)
×
10)
Connector (CN302)
7
8
1
Flat type wire (CN304)
6
Three screws (+BVTT 3
3-4. TAPE MECHANISM DECK
5
Front panel section
×
6)
4
Bracket (Heart cam L)
Screw (+BVTP 3
3
Screw (+BVTP 2.6
5
Five screws (+BVTP 2.6
×
10)
×
8)
×
8)
1
Screw (+BVTP 2.6
×
8)
2
Bracket (Heart cam R)
6
Tape mechanism deck
8
)
3-5. PANEL BOARD
4
Ring (Vol)
1
Knob (Volume)
3
2
Hexagon nut
Bracket (Volume)
7
Six claws
5
8
Panel board
6
Cut the fourteen melted-connection points with a cutting plier.
3-6. SUB-TRANS BOARD AND TRANS BOARD
1
Connector (CN975)
8
(+BVTT 4
9
Two screws (+BVTT 4
qa
Trans board
×
6)
q;
Trans
Two screws
×
Note: When attching the panel board, refer to "Service Note" on page 4.
2
Connector (CN974)
7
Panel, back
6
Five screws
(+BVTP 3
6)
4
Sub-trans
board
3
Two screws
(+BVTP 3
×
10)
×
10)
5
Five screws
(+BVTP 3
×
10
9
)
3-7. MAIN BOARD AND AMP BOARD
4
Three screws (+BVTP 3
5
AMP board
3
Two screws (+BVTP 3
×
10)
×
10)
7
Heat sink
6
Two screws (+BVTP 3
2
Main board
×
10)
3-8. LEAF SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD
2
Remove the two solderings.
5 Leaf
4
Five claws
3
1
Two screws (+BVTP 3
SW board
1
Remove the two solderings.
Remove the four solderings.
×
8
10
7
Head (A) board
6
Screw (+PS 2.6
×
9
5)
8
Head (B) board
Screw (+PS 2.6
×
5)
)
3-9. BASE UNIT
5
Two insulators
Base unit
3
4
Two insulators
1
Flat type wire (CN101
2
Four screws (+PTPWH 2.6)
3-10. DRIVER BOARD, MOTOR BOARD AND ADDRESS SENSOR BOARD
q;
qa
Tray
3
Connector (CN701)
1
Screw (+BVTP 2.6
Screw (+PTPWH 2.6
qs
Screw (+BVTP 2.6
qd
Address sensor board
2
Driver board
×
8)
7
×
Motor board
×
8)
8)
5
Three screws (+BVTP 2.6
4
Flat type wire (CN721)
6
Remove the two solderings of motor.
8
Connector (CN722)
×
8)
9
Pull-out the disc tray.
11
SECTION 4
TEST MODE
[MC Cold Reset]
The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer.
Procedure:
1. Press three buttons x , ENTER , and ?/1 simulta-neously.
2. The fluorescent indicator tube displays COLD RESET and
the set is reset.
[CD Ship Mode]
This mode moves the pickup to the position durable to vibra­tion. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press CD button and 1/u button simultaneously.
3. After the "STANDBY" display blinks six times, a message
LOCK is displayed on the fluorescent indicator tube, and the CD ship mode is set.
[MC Hot Reset]
This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged in and out.
Procedure:
1. Press three buttons x , ENTER , and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[CD Service Mode]
This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pickup.
Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function “CD”.
3. Press three buttons x , ENTER , and OPEN/CLOSE simul-
taneously.
4. The CD service mode is selected.
5. With the CD in stop status, turn the shuttle knob clockwise to
move the pickup to outside track, or turn the shuttle knob counter-clockwise to inside track.
6. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2.
Note: Always move the pickup to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
Do not run the sled motor excessively, otherwise the gear can be chipped.
[Change-over of MW Tuner Step between 9 kHz and 10 kHz]
A step of MW channels can be changed over between 9 kHz and 10 kHz.
Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function TUNER, and press TUNER/BAND
button to select the BAND “MW”.
3. Press ?/1 button to turn the set OFF.
4. Press ENTER and ?/1 buttons simultaneously , and the display
of fluorescent indicator tube changes to MW 9 k STEP or MW 10 k STEP, and thus the channel step is changed over.
[GC Test Mode]
This mode is used to check the software version, FL tube, LED, keyboard and VACS.
Procedure:
1. Press three buttons x , ENTER , and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3. When you want to enter the software version display mode,
press DISC 1 . The model number and destination are displayed.
4. Each time DISC 1 is pressed, the display changes starting
from MC version, GC version, VC version, CD version, CM version, ST version, TC version, TA version, TM version and BR version in this order, and returns to the model number and destination display .
5. When DISC 3 is pressed while the version numbers are being
displayed except model number and destination, year, month and day of the software creation appear. When DISC 3 is pressed again, the display returns to the software version display . When DISC 1 is pressed while year, month and day of the software creation are being displayed, the year, month and day of creation of the software versions are displayed in the same order of version display.
6. Press DISC 2 button, and the key check mode is activated.
7. In the key check mode, the fluorescent indicator tube displays
KEY0 VOL0. Each time a button is pressed, KEY value increases. However, once a button is pressed, it is no longer taken into account. VOL value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–” direction.
8. Also when DISC 3 is pressed after lighting of all LEDs and FL
tubes, value of VACS appears.
9. T o e xit from this mode, press three b uttons in the same manner
as step 1, or disconnect the power cord.
[VACS ON/OFF Mode]
This mode is used to switch ON and OFF the VACS (Variable Attenuation Control System).
Procedure:
Press the ENTER and SPECTRUM buttons simultaneously. The message “VACS OFF or VACS ON appears.
12
[MC Test Mode]
This mode is used to check operations of the respective sections of Amplifier, Tuner, CD and Tape.
Procedure:
1. Press the ?/1 button to turn on the set.
2. Press the three buttons of x , ENTER and DISC 3 simultaneously.
3. A message TEST MODE appears on the FL display tube.
4 When f (CURSOR UP) button is pressed, GEQ increases to
its maximum and a message GEQ ALL MA appears.
5. When F (CURSOR DOWN) button is pressed, GEQ decreases to its minimum and a message GEQ ALL M1 appears.
6. When g (CURSOR LEFT) or G (CURSOR RIGHT) button is pressed, GEQ is set to flat and a message “GEQ FLAT appears.
7. When the VOLUME control knob is turned clockwise even slightly, the sound volume increases to its maximum and a message “V OLUME MAX” appears for two seconds, then the display returns to the original display.
8. When the V OLUME control knob is turned counter-clockwise even slightly, the sound volume decreases to its minimum and a message “VOLUME MIN” appears for two seconds, then the display returns to the original display.
9. In the test mode, the default-preset channel is called even when the TUNER is selected and an attempt is made to call the preset channel that has been stored in memory, by oper ating the Shuttle knob. (It means that the memory is cleared.)
10. When CD is selected and the EDIT button is pressed, the disc that is being chucked at this moment becomes the default setting. It means that the default disc only is accessed when any other discs are selected even though the display indication changes accordingly. At the same time, the DISK SKIP EX­CHANGE and OPEN/CLOSE cannot be accepted. (It means that the tray motor and the turntable motor are disabled of their operation.)
11. When a tape is inserted in Deck B and recording is started, the input source function selects VIDEO automatically.
12. When x button is pressed to stop recording, the Tape (Deck) B is selected and tape is rewound using the Shuttle knob, tape is rewound, tape is stops at around the record-starting position and playback of the recorded portion of the tape is started. If P A USE is inserted even once during recording, ta pe is rewound to the position around the P AUSE position and is played back.
13. When the CD SYNC HI-DUB Button is press during playback of Deck B, either normal speed or high speed can be selected by this button.
14. Select the desired loop by pressing the PLAY MODE b utton. Insert a test tape AMS-110A or AMS-RO to Deck A.
15. Press the SPECTRUM button to enter the AMS test mode.
16. After a tape is rewound first, the FF AMS is checked, and the mechanism is shut off after detecting the AMS signal twice.
17. Then the REW AMS is checked and the mechanism is shut off after detecting the AMS signal twice.
18. When the check is complete, a message of either OK or NG appears.
19. When you want to exit this mode, press the ?/1 button twice. The cold reset is enforced at the same time.
13
[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
If an error occurred: The aging operation stops and display status.
If no error occurs: The aging operation continues repeatedly.
1. Operating method of Aging Mode
Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray. Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x , ENTER , and
DISC SKIP/EX-CHANGE simultaneously.
4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [MC Cold Reset].
3. Aging Mode in CD section
1) Display state
No error occurs
Display
AGING[*][*][*][*]
Note:
[*][*][*][*]
Error display
E ** s ## $$ %%
12 34 5
1 **
2 s 3 ##
4 $$
5 %%
: Number of aging operations
The error No. 00 indicates the newest error. As the error No. increases, it means the older error. When you want to retrieve the error history, press the PLAY MODE button in the case of mechanism error. Or press the REPEAT button in the case of NO DISC error.
M: Mechanism error Dont care
High order digits only D: Stopped during closing due to problems other than mechanism. E: Stopped during opening due to problems other than mechanism. C: Stopped during chucking due to problems other than mechanism. F: Stopped during EX-opening due to problems other than mechanism.
Emergency related errors (High order digits only) 1: Stopped during chuck-up 2: Stopped during chuck-down 3: Time out by EX-OPEN 5: Time out by EX-CLOSE
D: No disc error 01: FOCUS ERROR
02: GFS ERROR 03: SETUP ERROR
01: NO DISC judgment without chucking retry 02: NO DISC judgment after chucking retry
Status at the time of NO DISC judgment (High order digits only) 1: STOP 2: SETUP 3: TOC READ 4: ACCESS 5: PLAY BACK 6: PAUSE 7: MANUAL SEARCH (PLAY) 8: MANUAL SEARCH (PAUSE)
When the buttons x , ENTER and DISC 1 are pressed simultaneously, number of time of the mechanism error and the NO DISC error can be checked. Display: EMC**EDC** **: Number of times of error (Maximum three times)
EMC: Mechanism error EDC: NO DISC error
When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.
14
2) Operation during aging mode In the aging mode, the program is executed in the following sequence. (1) The disc tray opens and closes. (2) The mechanism accesses DISC 2 and makes an attempt to
read TOC. However, since there are no discs, a message CD2 NO DISC appears.
(3) The mechanism accesses DISC 3 and a message CD3 NO
DISC appears. (4) The disc tray turns to select a disc1. (5) A disc is chucked. (6) TOC of disc is read. (7) The pickup accesses to the track 1, and playing 2 seconds. (8) The pickup accesses to the last track, and playing 2 seconds. (9) Every time when an aging operation of step 1 to step 8 is
complete, the display “AGING[*][*][*][*] value increases
as the number of aging operations is counted up. (10) Returns to step 1.
3. Aging Mode in Tape Deck section
1) Display state
No error occurs
Display action now
Error occurred
Display action last time
NO. Display action Action contents Final timing
1 TAPE A AG-1 Rewind the TAPE A, B The top of tape 2 TAPE A AG-2 FWD play the TAPE A 2 minutes playing 3 TAPE A AG-3 F.F. the TAPE A 20 second FF or the end
4 TAPE A AG-4 REV play the TAPE A 2 minutes playing 5 TAPE A AG-5 Rewind the TAPE A The top of tape 6 TAPE B AG-2 FWD play the TAPE B 2 minutes playing 7 TAPE B AG-3 F.F . the TAPE B 20 second FF or the end
8 TAPE B AG-4 REV play the TAPE B 2 minutes playing 9 TAPE B AG-5 Rewind the TAPE B The top of tape
of tape
of tape
2) Operation during aging mode In the aging mode, the program is executed in the following sequence. (1) Rewind is executed up to the top of tape A and B. (2) A tape on FWD side is played for 2 minutes. (3) FF is executed up to either made for 20 second or the end of
tape.
(4) A tape is reversed, and the tape on REV side is played for 2
minutes. (5) Rewind is executed up to the top of tape. (6) Returns to step 2, and repeat steps from 2 to 5.
[Function Change Mode]
* elect either VIDEO or MD of the external FUNCTION input.
Procedure:
1. Turn on the power.
2. Press the two buttons ENTER and ?/1 at the same time.
The main power is turned on and the other function of the previous function is selected and displayed. MD or VIDEO.
15
SECTION 5
r
MECHANICAL ADJUSTMENTS
SECTION 6
ELECTRICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened swab:
record/playback heads pinch rollers erase head rubber belts capstan idlers
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
Torque Measurement
Mode Torque meter
FWD
FWD back tension
REV REV
back tension FF/REW
FWD tension
REV tension
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
31 to 71 g cm
(0.43 – 0.98 oz inch)
2 to 6 g cm
(0.02 – 0.08 oz inch)
31 to 71 g cm
(0.43 – 0.98 oz inch)
2 to 6 g cm
(0.02 – 0.08 oz inch)
71 to 143 g cm
(0.98 – 1.99 oz inch)
100 g or more
(3.53 oz or more)
100 g or more
(3.53 oz or more)
DECK SECTION
1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the parts adjust.
4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)
6. The adjustments should be performed for both L-CH and R­CH.
7. Switches and controls should be set as follows unless otherwise specified.
Test Tape
Tape Signal Used for
P-4-A100 10 kHz, –10 dB Azimuth Adjustment
WS-48B 3 kHz, 0 dB Tape Speed Adjustment
P-4-L300 315 Hz, 0 dB Level Adjustment
Record/Playback Head Azimuth Adjustment
0 dB=0.775 V
DECK A DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback
test tape P-4-A100 (10 kHz, –10 dB)
set
main board CN301 Pin 3 (L-CH) Pin 1 (R-CH)
main board CN301 Pin 2 (GND)
level mete
+ –
16
2. Turn the adjustment scre w and check output peaks. If the peaks
e
r
+
set
test tape P-4-L300 (315 Hz, 0 dB)
main board CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
level meter
do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
Output level
within 1dB
L-CH peak
R-CH peak
within 1dB
Screw position
L-CH peak
Screw position
R-CH peak
Tape Speed Adjustment
Note: Start the Tape Speed adjustment as below after setting to the test
mode. In the test mode, the tape speed is high during pressing the
DECK B
SD SYNC HI-DUB button.
Procedure:
1. Turn the power switch on.
2. Press the x button, ENTER button and DISC 3 button simultaneously. (The TEST MODE on the fluorescent indicator tube display while in the test mode.) To exit from the test mode, press the ?/1 button.
Mode: Playback
test tape WS-48B (3 kHz, 0 dB)
frequency counte
3. Mode: Playback
test tape P-4-A100 (10 kHz, –10 dB)
L-CH
MAIN board CN301 set
R-CH
waveform of oscilloscope
in phase 45° 90° 135° 180°
pin 3
pin 2
L R
pin 1
good
oscilloscop
V
wrong
H
4. After the adjustments, apply suitable locking compound to the pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
set
main board CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
+
1. Insert the WS-48B into the deck B.
2. Press the gG button on the deck B.
3. Press the SD SYNC HI-DUB button in playback mode. Then at HIGH speed mode.
4. Adjust RV1001 on the LEAF SW board do that frequency counter reads 6,000 ± 30 Hz.
5. Press the SD SYNC HI-DUB button. Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency counter reads 3,000 ± 15 Hz.
Adjustment Location: LEAF SW board
Playback level Adjustment
DECK A DECK B
Procedure:
Mode: Playback
forward
reverse
Deck A is RV302 (L-CH) and RV352 (R-CH), Deck B is RV303 (L-CH) and RV353 (R-CH) so that adjustment within adjustment level as follows.
Adjustment Level:
CN301 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level difference between the channels: within ±0.5 dB
Adjustment Location: MAIN board
Sample Volue of Wow and Flutter: 0.3% or less W. RMS
(WS-48B)
17
REC Bias Adjustment DECK B
e
r
r
Procedure:
INTRODUCTION When set to the test mode performed in Tape Speed Adjustment, when the tape is rewound after recording, the REC memory mode which rewinds only the recorded portion and playback is set. This REC memory mode is convenient for performing this adjustment. During recording, the input signal FUNCTION will automatically switch to VIDEO. (If do not operation of stopped from recording complete, and rotette of shuttle knob then rewind to recording start position.)
4. Mode: Record
MD/VIDEO (AUDIO) IN
AF OSC
315 Hz, 50 mV (–23.8 dB)
attenuator
5. Mode: Playback
600
blank tape CS-123
set
1. Press MD/VIDEO button to select VIDEO. (This step is not necessary if the above test mode has already been set.)
2. Insert a tape into deck B.
3. After press REC PAUSE/ST ART button, press REC P AUSE/ START button, then recording start.
4. Mode: Record
MD/VIDEO (AUDIO) IN
1) 315 Hz
2) 10 kHz
AF OSC
attenuator
50 mV (–23.8 dB)
 
600
blank tap CN-123
set
5. Mode: Playback
recorded portion
set
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
level mete
+
recorded portion
set
level mete
+
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
6. Confirm playback the signal recorded in step 3 become adjustable level as follows. If these levels do not adjustable level, adjustment the RV301 (L-CH) and R V351 (R-CH) on the MAIN board to repeat steps 4 and 5.
Adjustable level:
CN301 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB) Adjustment Location: MAIN board
[MAIN BOARD] (Component Side)
T601
RV611
REC LEVEL (L)
(B)
PB LEVEL (L)
(A)
6. Confirm playback the signal recorded in step 3 become adjustable level as follows. If these levels do not adjustable level, adjustment the RV304 (L-CH) and RV354 (R-CH) on the A UDIO board to repeat steps 4 and 5.
Adjustable level: Playback output of 315 Hz to playback output
of 10 kHz: ±1.0 dB
Adjustment Location: MAIN board
REC Level Adjustment
DECK B
Procedure:
INTRODUCTION When set to the test mode performed in Tape Speed Adjustment, when the tape is rewound after recording, the REC memory mode which rewinds only the recorded portion and playback is set. This REC memory mode is convenient for performing this adjustment. During recording, the input signal FUNCTION will automatically switch to VIDEO. (If do not operation of stopped from recording complete, and rotate of shuttle knob then rewind to recording start position.)
1. Press MD/VIDEO button to select VIDEO. (This step is not necessary if the above test mode has already been set.)
2. Insert a tape into deck B.
3. After press REC PAUSE/ST ART button, press REC P AUSE/ START button, then recording start.
PB LEVEL (R)
(A)
PB LEVEL (R)
(B)
REC LEVEL (R)
(B)
REC LEVEL (L)
(A)
CN301
RV351
REC LEVEL (R)
[LEAF SW BOARD] (Component Side)
TAPE SPEED

(NORMAL) (HIGH)
RV1002
RV1001
13
RV301
RV302
RV352
RV353
RV303
PB LEVEL (L)
(B)
(A)
CN1001
CN304
CN302
CN303
RV304
RV354
18
FM Tuned Level Adjustment
FM RF SSG
75 coaxial
Carrier frequency : 98 MHz Modulation : AUDIO 1 kHz, 75 kHz deviation (100%) Output level : 28 dB (at 75 W open)
set
FM ANTENNA terminal (TM601)
CD SECTION
Note :
1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
S-Curve Check
Procedure:
1. Supply a 28 dB 98 MHz signal from the ANTENN A terminal.
2. Tune the set to 98 MHz.
3. Adjust RV611 to the point (moment) when the TUNED indicator will change from going off to going on.
Adjustment Location: MAIN board
Null Adjustment
FM RF SSG
75 coaxial
set
Carrier frequency : 98 MHz Modulation : AUDIO 1 kHz, 75 kHz deviation (100%) Output level : 60 dB (at 75 W open)
FM ANTENNA terminal (TM601)
Procedure:
1. Supply a 60 dB 98 MHz signal from the ANTENN A terminal.
2. Tune the set to 98 MHz.
3. Measure voltage between pin 21 of IC 601. Adjust T601 ubtil the voltage becomes 0 V.
Oscilloscope
BD board
TP(FEO) TP(VC)
Procedure :
1. Connect oscilloscope to TP (FEO).
2. Connect between TP (FEI) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
4. Turn Power switch on.
5. Load a disc (YEDS-18) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus search)
6. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 4 ±1 Vp-p.
S-curve waveform
symmetry
A
within 4 ±1Vp-p
B
Adjustment Location: MAIN board
Adjustment Location
[MAIN BOARD] Component side
NULL
T601
RV611
FM TUNED LEVEL
CN301
RV351
7. After check, remove the lead wire connected in step 2 and 3.
Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
oscilloscope
BD board
TP(RF) TP(VC)
Procedure :
CN304
13
RV301
RV303
RV302
RV352
RV353
CN302
CN303
RV304
RV354
1. Connect oscilloscope to TP (RF).
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3. Turned Power switch on.
4. Load a disc (YEDS-18) and playback.
5. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
6. After check, remove the lead wire connected in step 2.
19
Note : Clear RF signal waveform means that the shape can be clearly
e
)
r
distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200mV TIME/DIV : 500ns
level : 1.45 ± 0.3Vp-p
E-F Balance (1 Track jump) Check
oscilloscop
BD board
TP(TEO) TP(VC)
Procedure :
1. Connect oscilloscope to TP (TEO) and TP (VC).
2. Turned Power switch on.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the gG button. (Becomes the 1 track jump mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope waveform.
1 track jump waveform
center of waveform
Adjustment Location:
[BD BOARD] (Conductor Side)
TP
TP
(AGCCON)
IC103
TP
(RF)
24
TP
(FEI)
1
40
41
12
TP
(TEO)
(FEO)
TP
(VC)
TP
(XPCK)
2021
IC101
61
60
TP
(DGND)
1 80
B
0V
level=1.3±0.6Vp-p
Specified level: –– × 100=less than ±22%
A B
symmetry
A (DC voltage
6. After check, remove the lead wire connected in step 1.
RF PLL Free-run Frequency Check
Procedure :
1. Connect frequency counter to test point (XPCK) with lead wire.
BD board
TP (XPCK)
frequency counte
2. Turned Power switch on.
3. Put the disc (YEDS-18) in to play the number five track. Confirm that reading on frequency counter is 4.3218MHz.
20
Loading...
+ 46 hidden pages