Sony HCDDH7BT User Manual

3-097-195-11(1)

Micro HI-FI

Component System

Operating Instructions

Owner’s Record

The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. ______________ Serial No. ______________

CMT-DH7BT

© 2007 Sony Corporation

CMT-DH7BT.GB.3-097-195-11(1)

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

CAUTION

The use of optical instruments with this product will increase eye hazard.

Notice for the customers in the U.S.A.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2GB

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUT

You ar modifi this m operat

This eq operat antenn

This eq radiati uncon FCC r Guidel This eq level th FCC r Guidel withou evalua it shou least 2 and pe hands,

U.S.A mode

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

des in und

point

plies l S.A. with

ound B the to

t

s,

re

l

ct e

e

tlet hich

ed

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

This equipment must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has a very low RF energy level that is deemed to comply with FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 without maximum permissive exposure evaluation (MPE). But it is desirable that

it should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and legs).

U.S.A., Canadian and Australian models only

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® partner, Sony Corporation

has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

About this manual

Icons, such as , listed at the top of each explanation indicate what kind of media can be used with the function being explained.

The English on-screen display is used for illustration purposes only.

The Control Menu items may be different depending on the disc.

The Setup Menu items may be different depending on the area.

3GB

CMT-DH7BT.GB.3-097-195-11(1)

Table of Contents

 

About this manual...............................

3

Playable discs ........................................

5

Guide to parts and controls .............

8

Getting Started

 

Hooking up the system....................

14

Hooking up the TV.............................

17

Setting the clock ................................

19

Performing QUICK SETUP ...............

20

Using the THEATRE SYNC

 

function .................................................

21

Disc

 

Playing a disc.......................................

23

Normal Play

 

Using play mode ................................

27

Searching/selecting a disc..............

31

Playing MP3/JPEG discs...................

34

Adjusting the delay between the

 

picture and sound .............................

39

A/V SYNC

 

Restricting playback of the disc....

39

CUSTOM PARENTAL CONTROL,

 

PARENTAL CONTROL

 

Using the DVD setup menu............

43

Tuner

 

Listening to the radio .......................

48

Bluetooth

 

Using the Bluetooth function........

52

Sound Adjustment

 

Adjusting the sound .........................

58

Other operations

 

Using the timer ...................................

59

Changing the display .......................

60

Viewing information about the

 

disc .........................................................

61

Hooking up optional

 

components.........................................

64

Additional Information

 

Troubleshooting.................................

66

Precautions...........................................

75

Specifications ......................................

76

Guide to the Control Menu

 

display....................................................

79

Language code list ............................

82

Bluetooth wireless technology .....

84

Playable Bluetooth devices ............

85

Glossary .................................................

86

Index...............................................................

89

4GB

Play

Type

DVD V

VR mo

VIDEO

CD

DATA

DATA

This sy

1)MP3

data.

2)JPEG File S Techn

3)A log Stand

“DVD tradem

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

....52

....58

....59

....60

....61

....64

....66

....75

....76

....79

....82

....84

....85

....86

.....89

Playable discs

Type

Characteristics

Icon used in

Logo

this manual

 

 

 

DVD VIDEO

DVD VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD-R*/-RW*/+R/+RW

 

 

 

 

 

 

 

in DVD VIDEO format

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* also in video mode

 

 

 

 

 

 

VR mode

DVD-R/-RW

 

 

 

 

 

 

 

 

 

 

 

 

 

in VR (Video Recording) mode

 

 

 

 

 

 

VIDEO CD

VIDEO CD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Super VCD*

CD-ROM*/-R*/-RW*

* in VIDEO CD or Super VCD format

CD

AUDIO CD*

 

 

 

 

 

 

 

 

CD-R*/-RW*

 

 

 

 

 

 

 

 

* in AUDIO CD format

DATA CD

CD-ROM/-R/-RW

 

 

 

 

 

 

 

 

 

in DATA CD format, containing

 

 

 

 

 

 

 

 

MP3 audio tracks1) and/or JPEG

 

image files2), and conforming to

 

ISO 96603) Level 1 or Level 2, or

 

Joliet (expansion format).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DATA DVD

DVD-ROM/-R/-RW/+R/+RW

 

 

 

 

in DATA DVD format containing

 

 

 

MP3 audio tracks1) and/or JPEG

 

image files2), and conforming to

 

UDF (Universal Disk Format).

This system can also play back discs with the following disc logos:

1)MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data. MP3 audio tracks must be in MPEG 1 Audio Layer 3 format.

2)JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File System”: Image standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association (JEITA)).

3)A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for Standardization).

“DVD+RW”, “DVD-RW”, “DVD+R”, “DVD VIDEO”, and the “CD” logos are trademarks.

Continued 5GB

CMT-DH7BT.GB.3-097-195-11(1)

Discs that cannot be played

Note on DualDiscs

CD-ROMs recorded in PHOTO CD format

DATA CDs recorded in MP3 PRO format

Data part of CD-Extras1)

Data part of Mixed CDs2)

Super Audio CDs

DVD Audio discs

DVD-RAMs

A DVD VIDEO with a different region code.

A disc that has a non-standard shape (e.g., heart, square, star).

A disc that has the adhesive cellophane tape or a sticker still left on it.

1)CD-Extra: This format records audio (AUDIO CD data) on the tracks in session 1 and data on the tracks in session 2.

2)Mixed CD: This format records data on the first track and audio (AUDIO CD data) on the second and subsequent tracks of a session.

Region code of DVD VIDEOs you

can play back on this system

Your system has a region code printed on the back of the unit and will only play back DVD VIDEOs labeled with identical region code.

DVD VIDEOs labeled ALL will also be played back on this system.

If you try to play back any other region code DVD VIDEO, the message “Playback prohibited by area limitations.” will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be labeled even though playing the DVD VIDEO is prohibited by area restrictions.

6GB

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to Compact Disc (CD) standard, playback on this product is not guaranteed.

Notes on CD-R/-RW and

DVD-R/-RW/+R/+RW

In some cases, CD-Rs/-RWs and DVD-Rs/-RWs/+Rs/+RWs cannot be played back on this system due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not be played back if it has not been correctly finalized. For more information, see the operation instructions for the recording device.

Note that some playback functions may not work with some DVD+RWs/ +Rs, even if they have been correctly finalized. In this case, view the disc by normal playback.

A disc created in Packet Write format cannot be played back.

Note on playback operations of

DVD VIDEOs and VIDEO CDs

Some playback operations of DVD VIDEOs and VIDEO CDs may be intentionally set by software producers.

Since t VIDEO the dis design not be instru VIDEO

Mus

copy

This p discs t (CD) s discs e techno record among do not may n

Note

This Sess (or a the fi audi reco play

If th AUD only back

The Sess is a form syste the fi CD

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

uct al ial e

m to ack

t be the dition of

g ed

ee

s Ws/ ctly sc by

mat

s of

ers.

Since this system play back DVD VIDEOs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVD VIDEOs or VIDEO CDs.

Music discs encoded with

copyright protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Notes on Multi Session disc

This system can play back Multi Session discs when an MP3 audio track (or a JPEG image file) is contained in the first session. Any subsequent MP3 audio tracks (or JPEG image files) recorded in later sessions can also be played back.

If the first session is recorded in AUDIO CD or VIDEO CD format, only the first session will be played back.

The system will recognize a Multi Session disc as an AUDIO CD if there is a session recorded in AUDIO CD format on the disc. However, the system will only play back the disc if the first session is recorded in AUDIO CD format.

Copyrights

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

This system incorporates Dolby* Digital and the DTS** Digital Surround System.

*Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

**Manufactured under license from Digital Theater Systems, Inc.

“DTS” and “ DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

The XM name and related logos are registered trademarks of XM Satellite Radio Inc.

(c) 2006 SIRIUS Satellite Radio Inc. “SIRIUS” and the SIRIUS dog logo are registered trademarks of SIRIUS Satellite Radio Inc.

7GB

CMT-DH7BT.GB.3-097-195-11(1)

Guide to parts and controls

This manual mainly explains operations using the remote, but the same operations can also be performed using the buttons on the unit having the same or similar names.

Unit (HCD-DH7BT/Compact Disc Receiver)

Front panel

Top panel

8GB

Remo

Unit:

79) Rem (11)

Press t Press t

STAN

Lights

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

Remote control (RM-SCD30)

can

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unit: (on/standby) (11, 69, 79)

Remote: TV 2) (on/standby) (11)

Press to turn on the system. Press to turn on the TV.

STANDBY indicator (71)

Lights up when the system is turned off.

BLUETOOTH indicator (60, 80)

Lights up when the Bluetooth function is active.

BLUETOOTH OPR (57)

Press to make a connection, disconnection, or pairing with a Bluetooth device.

(eject) (59, 72)

Press to eject the disc.

Disc slot (73)

+/ (15, 19)

Press to select an album.

PRESET +/ (XX)

Press to return the settings to the default setting.

/ (go backward/ forward) (19, 54)

Press to select a track or file.

Remote: TV CH +/ 2) (11)

Press to change the TV channels.

Remote: SLOW / (34)

Press to watch the slow-motion play.

Remote: TUNING +/ (51)

Press to tune in the desired station.

/ (rewind/fast forward) (34, 54)

Press to find a point in a track or file.

Continued

controls and parts to Guide

9GB

CMT-DH7BT.GB.3-097-195-11(1)

AUDIO IN jack (55, 56, 68)

Connect to an optional audio component.

PHONES jack (55)

Connect the headphones.

DISPLAY (19)

Press to display the disc information or clock in the front panel display.

PROGRESSIVE (XX, XX)

Press to change the output video format (INTERLACE or PROGRESSIVE format).

DSGX (XX)

Press to select the sound effect.

IR Receptor (52)

Unit: DVD (play) (XX, XX)

Press to select the DVD function. Press to start playback of a disc.

Unit: BLUETOOTH (XX, XX)

Press to select the Bluetooth function. Press to start playback of the music on the Bluetooth device (Bluetooth mobile phone, etc.).

Unit: TUNER/BAND (XX, XX)

Press to select the TUNER function. Press to switch among FM, AM, XM and SIRIUS band.

10GB

Unit: AUDIO IN (XX, XX)

Press to select the AUDIO IN function.

FUNCTION +/ (14, 51, 54, 63, 70, 78)

Press to select the function.

Unit: REPEAT/FM MODE (XX, XX) Remote: FM MODE (53) Remote: REPEAT (25)

Press to select FM reception mode (monaural or stereo).

Press to listen to a disc, a single track or file repeatedly.

(stop) (19, 39, 52, 54, 70, 81)(pause) (19, 54)

Press to stop or pause playback.

Remote: 1) (play) (19, 42, 54, 56, 68, 70)

Press to start playback.

Remote: TV VOL +/ 1)2) (11)

Press to adjust the TV volume.

VOLUME +/ 1) (51, 69, 73, 79)

Press to adjust the volume.

DIMMER (20)

Press to adjust the brightness of the display.

PICTURE NAVI (29)

Press to select the VIEWER format for searching the chapters, titles and tracks. Press to display the thumbnail pictures.

AUDI

Press on the

SUBT

Press subtitl

ANG

Press with

DVD

Press TV sc Press

EQ (5

Press

DI 92)

Press TV sc

TV2) (

Press

ADV

Press playba

REPL

Press playba

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

ion.

3,

XX)

k or

1)

4,

)

for cks. res.

AUDIO (29, 37, 63, 78)

Press to display the current audio signal on the TV screen.

SUBTITLE (38)

Press to switch the language of the subtitle (DVD VIDEO).

ANGLE (38)

Press to change the angle (DVD VIDEO with multi-angles only).

DVD/TUNER MENU (25, 51)

Press to display the MENU items on the TV screen.

Press to preset the radio station.

EQ (57, 78)

Press to adjust the sound level.

DISPLAY (15, 21, 23, 39, 63, 75, 92)

Press to display the Control Menu on the TV screen.

TV2) (11)

Press to operate the TV functions.

ADVANCE(20)

Press to advance the current scene during playback.

REPLAY(20)

Press to replay the previous scene during playback.

STEP/ STEP (20)

Press to play one frame at a time when playback is paused.

RETURN (26)

Press to return to the previous menu on the TV screen.

/ / / (14, 22, 39, 50, 58, 69, 84)

Press to select the MENU items.

ENTER (14, 19, 39, 50, 63, 69)

Press to enter the settings.

DVD TOP MENU (25)

Press to display the DVD title on the TV screen.

CLEAR (15, 48)

Press to delete a pre-programmed track or file.

Press to delete a SIRIUS Parental Lock password entry.

Press to erase the pairing registration information of the Bluetooth device.

-/--2) (11)

Press to change the entering mode for a single digit and double digit number.

Numeric buttons1) (11, 19, 40, 53)

Press to select a track, file or satellite channel.

Press to enter a SIRIUS Parental Lock password.

Press to enter a Bluetooth passcode.

10/02)

Press to enter a double digit number.

Continued

controls and parts to Guide

11GB

CMT-DH7BT.GB.3-097-195-11(1)

XM (XX, XX)

Press to select XM band.

SIRIUS (XX, XX)

Press to select SIRIUS band.

CATEGORY +/ (XX, XX)

Press to select a satellite radio category.

CATEGORY MODE (XX, XX)

Press to select the tuning mode for XM or SIRIUS band.

TIME/TEXT (73)

Press to change the information in the front panel display.

TV/VIDEO2) (11)

Press to switch the input sources.

SLEEP (53, 69)

Press to set the Sleep Timer.

TIMER MENU (14, 69)

Press to set the clock and the timers.

THEATRE SYNC (XX, XX)

Press to register the input sources and functions.

Press to activate the THEATRE SYNC function.

1)The numeric button 5, TV VOL +, VOLUME + and buttons have a tactile dot. Use the tactile dot as a reference when operating the system.

2)This button is used to operate a Sony TV. For details, see “Operating a Sony TV” on page 11.

12GB

Displa

In

In

Li

Li (x

Li (6

In

Li

Li sel

Li is

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

Sony HCDDH7BT User Manual

Display

controls and parts to Guide

Indicates the selected function. (21)

Lights up when “P AUTO” or

Indicates the selected play mode. (16)

“P VIDEO” is selected. (xx)

Lights up when timer is set. (56)

Lights up when playing VIDEO CD

Lights up when a station is tuned in.

with PBC. (xx)

(xx)

Lights up when an MP3 disc is

Lights up when DSGX is turned on.

loaded. (xx)

(62)Indicates the track/file information.

Indicates the Playback status. (xx)Lights up when DTS is selected. (63)

Lights up when Dolby Digital is selected. (xx)

Lights up when CATEGORY MODE is selected. (xx)

(xx)

Lights up when chapter or title number is displayed. (xx)

Indicates the type of disc being played back. (xx)

Displays the text information. (xx)

13GB

CMT-DH7BT.GB.3-097-195-11(1)

Getting Started

Hooking up the system

Wall socket

Right speaker Left speaker

SiriusConnect Home tuner (not supplied)

Home indoor/outdoor antenna (not supplied)*AC power adaptor (not supplied)*

DIN cable (not supplied)*

XM Mini-Tuner and Home Dock (not supplied)FM lead antenna (Extend it horizontally.)Connect white side.

AM loop antenna

* Supplied with SiriusConnect Home tuner

Wall socket

FM/AM antennas

Find a location and an orientation that provide good reception, and then set up the antenna.

Keep the antennas away from the speaker cords and the power cord to avoid picking up noise.

14GB

SI

Conne When tuner the AC tuner t Keep t antenn from t cord to

XM

Conne

Dock.

Satellit

Sp

Po

Conne If the s not fit the plu an ada

Inse

batt

Note

If you d of time damage

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

hat t up

eaker

SIRIUS antenna

Connect the SiriusConnect Home tuner. When you use the SiriusConnect Home tuner with this system, be sure to connect the AC power adaptor supplied with the tuner to a wall socket.

Keep the SiriusConnect Home tuner, antenna, and AC power adaptor away from the speaker cords and the power cord to avoid picking up noise.

XM antenna

Connect the XM Mini-Tuner and Home Dock. For details, see “To receive the XM Satellite Radio” (page xx)

Speakers

Power

Connect the power cord to a wall socket. If the supplied adaptor on the plug does not fit your wall socket, detach it from the plug (only for models equipped with an adaptor).

Tip

With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.

Attaching the speaker pads

Attach the supplied speaker pads at each corner on the bottom of the speakers

to stabilize the speakers and to prevent them from slipping.

Front speaker of SS-CDH3

Started Getting

Inserting two R6 (size AA)

batteries into the remote

Note

If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

When carrying this system

Perform the following procedure to protect the DVD mechanism.

Use buttons on the unit for the operation.

1Press / to turn on the system, then press DVD .

2Make sure that no disc is loaded in the system and check that “No Disc” appears.

3Press / to turn off the system and check that “STANDBY” disappears.

4 Unplug the power cord.

Continued 15GB

CMT-DH7BT.GB.3-097-195-11(1)

Receiving the XM Satellite

Radio

ABOUT XM SATELLITE RADIO

XM offers over 170 digital radio channels: the most commercial-free music channels, premier news, sports, talk, and traffic and weather in 21 metro markets. XM’s on-air hosts broadcast live from studios in Washington, D.C., New York City and Nashville.

For more information or to subscribe in the US, visit xmradio.com or call Listener Care at 1-800-XMRADIO (1-800-967-2346).

XM READY® LEGAL

XM monthly service subscription sold separately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM service. Installation costs and other fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channel

blocking is available for XM radio receivers by calling 1-800-XMRADIO (1-800-967-2346). For a full listing of the XM commercial-free channels and advertising supported channels, visit lineup.xmradio.com. Subscriptions subject to Customer Agreement available at xmradio.com. XM service only available in the 48 contiguous United States. XM Satellite Radio and XM Ready are trademarks of XM Satellite Radio Inc. (C)2006 XM Satellite Radio Inc. All rights reserved.

XM READY® SUBSCRIPTIONS

Once you have installed the XM Mini-Tuner Dock, inserted the XM Mini-Tuner, connected the XM Dock to your XM Ready® home audio system, and installed the antenna, you are ready to subscribe and begin receiving XM programming.

There are three places to find your eight character XM Radio ID: on the

XM Mini-Tuner, on the XM Mini-Tuner package, and on XM Channel 0. Record the Radio ID in the following eight squares for

reference.

Note: The XM Radio ID does not use the letters “I”, “O”, “S” or “F”. Activate your XM Satellite Radio service in the U.S. online

at http://activate.xmradio.com or call 1-800-XM-RADIO (1-800-967-2346). You will need a major credit card. XM will send a signal from the satellites to activate the full channel lineup. Activation normally takes 10 to 15 minutes, but during peak busy periods you may need to keep your XM Ready home audio system on for up to an hour. When you

can access the full channel lineup on your XM Ready home audio system you are done.

16GB

Rec

Rad

SIRIU On Ra

With e music t talk an always

The o musi musi heard

Live bigge week and o a wee over exclu

Enter be fo of Ho Jeff F Maxi

Espe her t Cosm Radi

Worl Fox, weat

Fami with Laug

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

he or

M

u nd full s 10 ods ome you

r XM

Receiving the SIRIUS Satellite

Radio

SIRIUS Satellite Radio: The Best Radio On Radio

With everything from 100% commercial-free music to in-depth sports coverage, plus news, talk and the hottest entertainment you can always hear exactly what you want.

The only home of 100% commercial-free music. Whether you’re discovering new

music, or rediscovering songs you haven’t heard in years you’ll hear it all on SIRIUS.

Live play-by-play and expert talk from the biggest leagues. NFL, every game, every week, everywhere. Plus NFL Radio 24/7 news and opinions from top NFL pros, 40 games

a week from NBA and College Sports from over 150 schools. Plus NASCAR moving exclusively to SIRIUS in January 2007.

Entertainment, Comedy and Talk that can’t be found anywhere else. From 2 channels of Howard Stern, Blue Collar Comedy with Jeff Foxworthy and Larry the Cable Guy to Maxim and Playboy Radio.

Especially for Women. Martha Stewart and her team will inspire you 24/7 along with Cosmo Radio, Deepak Chopra Wellness Radio and other exclusive talk show hosts.

World Class News, traffic and weather. Fox, CNN, NPR and BBC. Local traffic and weather for the top 20 cities.

Family & Kids: G-rated fun for everyone with Radio Disney, Discovery Kids Channel, Laugh Comedy and more.

Hooking up the TV

Connect the video input jack of your

TV to the VIDEO OUT jack with the

supplied video cord. Getting Started

When connecting a video deck

Connect the video deck to the TV using a video cord (not supplied). However, do not connect this unit to the TV through the video deck. Otherwise, you may experience video leakage when watching video images from this system. Connect this unit directly to the TV as shown below.

TV

Video deck

 

Unit

 

Do not connect directly

Continued 17GB

CMT-DH7BT.GB.3-097-195-11(1)

Tip

For higher quality video images:

Use the optional component video cords to connect the COMPONENT VIDEO input jacks on your TV to the COMPONENT VIDEO OUT jacks of this unit. If your TV is compatible with progressive format file signals, use this connection and press

PROGRESSIVE on the unit repeatedly until “P AUTO” or “P VIDEO” appears in the display (page 16).

You can use an optional S Video cord to connect the S VIDEO input jack on your TV to the S VIDEO OUT jack of this unit.

Changing the format of the video signal output from COMPONENT VIDEO OUT jacks

Progressive is a method for displaying TV images that reduces flickering and sharpens the image. To use this method, you need to connect to a TV that can accept progressive signals.

You can output video signals from COMPONENT VIDEO OUT jacks in INTERLACE or PROGRESSIVE format.

1Press FUNCTION +/

repeatedly to select “DVD” (or press DVD on the unit).

2Press PROGRESSIVE on the unit repeatedly.

Select “P AUTO” or “P VIDEO” if your TV accepts progressive signals and the TV is connected to the COMPONENT VIDEO OUT jacks. Otherwise, select “INTERLACE”.

P AUTO (PROGRESSIVE AUTO):

The system automatically detects the software type and selects the appropriate conversion method.

18GB

P VIDEO (PROGRESSIVE VIDEO):

The system fixes the conversion method to PROGRESSIVE VIDEO for video-based software.

Select this if the image is not clear when you select “P AUTO”.

About DVD VIDEO software types and the conversion method

The DVD VIDEO software can be divided into 2 types:

Film-based software

Film-based software is derived from film and displays the images at 24 frames per second.

Video-based software

Video-based software is derived from TV, such as dramas and sitcoms and displays images at 30 frames or 60 fields per second.

Some DVD VIDEO contains both types of software. In order for these images to appear in your TV naturally when the video output is in progressive format, the progressive signals need to be converted to match your DVD VIDEO software.

Note

There would be no image on your TV or the image is not clear if your setting does not match your TV or connection.

Whe

Turn o input s from t

Opera

You ca operat been m

To

Turn t or off

Switch input s betwee and ot source

Select chann

Adjust volum speake

*For d and p (For press

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

O):

EO

ar

and

m

rom nd

ypes s to he

t, the rted re.

the

When using a TV

Turn on the TV and select the video input so that you can view the pictures from this system.

Operating a Sony TV

You can use the following buttons to operate a Sony TV. These buttons have been marked in orange.

To

Hold down TV

 

and press

Turn the TV on

TV /

or off

 

Switch the TV’s

TV/VIDEO

input source

 

between the TV

 

and other input

 

sources

 

Select the TV

TV CH +/

channels

or numeric

 

buttons *

Adjust the

TV VOL +/

volume of the TV

 

speaker(s)

 

*For double digit number, hold down TV and press -/-- , then press the number. (For example, hold down TV ,

press -/-- , then 2 and 5 for entering 25.)

Setting the clock

Use buttons on the remote to set the clock.

1Press / to turn on the system.

2Press TIMER MENU .

The hour indication flashes in the display.

If “PLAY SET?” flashes in the display, press or repeatedly

to select “CLOCK SET?”, then press ENTER .

3Press or repeatedly to set the hour.

4Press ENTER .

The minute indication flashes in the display.

5Press or repeatedly to set the minute.

6Press ENTER .

The clock starts functioning.

Note

The clock settings are canceled when you disconnect the power cord or if a power failure occurs.

To display the clock when the system is off

Press DISPLAY .

The clock is displayed for about 8 seconds.

Continued

Started Getting

19GB

CMT-DH7BT.GB.3-097-195-11(1)

Performing QUICK

SETUP

Before using the system, you can make the minimum basic adjustments in QUICK SETUP. If you do not want

to perform QUICK SETUP, press CLEAR in step 3. The guide message will disappear from the TV screen.

1Turn on your TV and select the video input.

2Press / to turn on the system.

Note

Make sure there is no disc in the unit. Otherwise, the guide message does not

appear. To perform QUICK SETUP, presson the unit to remove the disc.

3Press FUNCTION +/

repeatedly to select “DVD” (or press DVD on the unit).

The guide message appears at the bottom of the TV screen.

4Press ENTER without inserting a disc.

The “LANGUAGE SETUP” display appears on the TV screen.

20GB

5Press or repeatedly to

select a language, then press ENTER .

Tips

The selected language is for “OSD”, “MENU” and “SUBTITLE ”.

The selectable language is different depending on the area.

The setting is selected and the “SCREEN SETUP” display appears on the TV screen.

6Press or repeatedly to select the setting that matches your TV type.

If you have a 4:3 standard TV:

Select 4:3 LETTER BOX or 4:3 PAN SCAN (page 45)

If you have a wide-screen TV or a 4:3 standard TV with wide-screen mode:

Select 16:9 (page 45)

7Press ENTER .

The setting is selected and the “QUICK SETUP is complete.” display appears on the TV screen.

The system is ready for playback. If you want to change each setting individually, see “Using the DVD setup menu” on page 43.

To quit QUICK SETUP

PressDISPLAY .

To rec

1Pre is st The scre

2Pre sele ENT

3Pre “QU

Note

The gu the TV for the (see pa

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

o ss

,

t

ars on

o hes

:

AN

or a reen

splay

.

ng D

To recall of QUICK SETUP settings

1PressDISPLAY when playback is stopped.

The Control Menu appears on the TV screen.

2Press or repeatedly to

select (SETUP), then press ENTER .

3Press or repeatedly to select “QUICK”, then press ENTER .

Note

The guide message appears at the bottom of the TV screen when you turn on the system for the first time or after performing “RESET” (see page 84).

Using the THEATRE SYNC function

THEATRE SYNC allows you to turn on your Sony TV and this system, changes the system’s function to “DVD” and then switches the TV’s input source you have set with just one button.

Preparing to use the THEATRE

SYNC function

Register the TV’s input source connected to this system.

Hold down

To select the

SLEEP and

following TV’s input

press

source

0No input source (Default)

1 to 8

VIDEO 1 to VIDEO 8

9COMPONENT 1

CLEAR

COMPONENT 2

 

COMPONENT 3

+

COMPONENT 4

The selected TV’s input source is memorized into the remote.

Started Getting

Continued 21GB

CMT-DH7BT.GB.3-097-195-11(1)

Operating the THEATRE SYNC

function

Keep the remote pointed in the direction of the TV until the TV is turned on and the input source is changed correctly, then press THEATRE SYNC .

If this function does not work, change the transmission time. The transmission time varies depending on the TV.

To change the transmission time

Hold down

To select the

and

following

press

transmission time

1

0.5 (Default)

2

1

3

1.5

4

2

5

2.5

6

3

7

3.5

8

4

22GB

CMT-DH7BT.GB.3-097-195-11(1)

Disc

Playing a disc

Normal Play

Depending on the DVD VIDEO or VIDEO CD, some operations may be different or restricted. Refer to the

operating instructions supplied with the disc.

Example: When playing a DVD VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Title number

 

Elapsed playing time

 

1Press FUNCTION +/

repeatedly to select “DVD” (or press DVD on the unit).

2Insert a disc with the label side facing up.

3 Press .

4Press VOLUME +/ to adjust the volume.

Notes

Depending on the system status, the volume

 

level may not appear on the TV screen.

 

When you turn on the system, the disc is

 

not pulled into the disc slot until “No Disc”

 

appears in the display. Do not attempt to

 

push in the disc until “No Disc” appears.

 

Do not load an 8 cm disc with an adaptor.

 

Doing so may cause the system to

Disc

malfunction.

 

 

 

 

 

When you remove a disc, handle the disc by

 

its edge and pull it straight out of the disc

 

slot. Do not touch the surface.

 

Other operations

 

 

 

 

 

To

Press

 

Stop playback

.

 

 

Pause playback

. Press again

 

 

 

or to resume

 

 

playback.

 

Select a track1),

or

 

 

chapter or

repeatedly during

 

video file

playback.

 

 

Or, press the numeric

 

 

buttons when

 

 

the Control Menu is

 

 

turned off, then press

 

 

ENTER 2).

 

 

Select an

+/ repeatedly

 

album3)

during playback or

 

 

when playback is

 

 

paused.

 

Locate a point

or

 

 

quickly in fast

during playback.

 

forward or fast

Each time you press

 

reverse (Lock

or , the

 

Search)4)5)

playback speed changes

 

 

cyclically.

 

To return to normal playback, press .

Continued 23GB

CMT-DH7BT.GB.3-097-195-11(1)

To

Press

 

Watch frame by SLOW or SLOW

frame (Slow-

when playback

motion Play)6)

is paused. Each time

 

you press SLOW

 

or SLOW

,

 

the playback speed

 

changes.

 

 

To return to normal

 

playback, press .

Play one

STEP to go to

frame at a

the next frame when

time (Freeze

playback is paused.

Frame)6)

Press STEP 7)

 

to go to the preceding

 

frame when playback is

 

paused.

 

 

To return to normal

 

playback, press .

Replay the

REPLAY

during

previous scene

playback. (Instant

 

Replay)7)

 

Briefly fast

ADVANCE

 

forward the

during playback.

current scene

(Instant Advance)7)

Switch to DVD

FUNCTION +/

function from

repeatedly (or press

another source

DVD on the

 

unit) (Automatic

 

Source Selection).

Remove the

on the unit.

disc

 

 

1)You cannot select an audio track during Lock Search operation of MP3 audio tracks.

2)DVD VIDEO, DVD-R/-RW in VR mode, VIDEO CD and AUDIO CD only.

3)MP3 audio tracks and JPEG image files only.

4)Except for JPEG image files.

5)Depending on the disc, the actual speed may differ.

6)DVD VIDEO, DVD-R/-RW in VR mode, and VIDEO CD only.

7)DVD VIDEO and DVD-R/-RW in VR mode only.

24GB

Notes

You cannot search for a still picture on a DVD-R/-RW in VR mode.

You may not be able to use the Instant Replay or Instant Advance function in Repeat Play mode or with some scenes.

Displaying multi-angles and

subtitles

Changing the angles

(DVD VIDEO only)

You can change the viewing angle while playing a DVD VIDEO on which various angles (multi-angles) for a scene are recorded.

Press ANGLE repeatedly during playback. Each time you press ANGLE , the angle changes.

Note

Depending on the DVD VIDEO, you may not be able to change the angle, even if multi-angles are recorded on the DVD VIDEO.

Displaying the subtitles

(DVD VIDEO and DVD-R/-RW in VR mode only)

You can turn the subtitles on or off while playing a DVD VIDEO or DVD-R/- RW in VR mode on which subtitles

are recorded. You can also change the language of the subtitles with DVD VIDEO, DVD-R/-RW in VR mode on which multilingual subtitles are recorded.

Press durin SUBT chang

Note

Depen not be multili VIDEO subtitle

Oth

Chan

When in mu the au VIDE tracks

When CD or the so and li chann speak track and th you ca speak

Press playba want. The d

When

Depen option varies When digits “Lang the sa more in mu

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

a

Replay

Play

d

hile arious

y not -angles

VR

while

-

he

on orded.

Press SUBTITLE repeatedly during playback. Each time you press SUBTITLE , the subtitle language changes or turns off.

Note

Depending on the DVD VIDEO, you may not be able to change the subtitles even if

multilingual subtitles are recorded on the DVD VIDEO. You also may not be able to turn the subtitles off.

Other useful functions

Changing the sound

When playing a DVD VIDEO recorded in multiple audio formats, you can select the audio format you want. If the DVD VIDEO is recorded with multilingual tracks, you can also change the language.

When playing a VIDEO CD, AUDIO CD or MP3 audio tracks, you can select the sound from the right or left channel and listen to the sound of the selected channel through both the right and left speakers. For example, when playing a track with the vocals on the right channel and the instruments on the left channel, you can hear the instruments from both speakers by selecting the left channel.

Press AUDIO repeatedly during playback to select the audio signal you want.

The default settings are underlined.

When playing a DVD VIDEO:

Depending on the DVD VIDEO, the option of language and audio format varies.

When a 4-digit number is displayed, the digits represent a language code (see “Language code list” on page 97). When the same language is displayed two or more times, the DVD VIDEO is recorded in multiple audio formats. Note that the

sound changes automatically depending on the disc.

When playing a DVD-R/-RW in VR

 

mode:

 

The number of audio tracks recorded on

 

a disc are displayed.

 

Example:

 

1: MAIN: the main sound of the audio

Disc

track 1.

 

1: SUB: the sub sound of the audio

 

track 1.

 

1: MAIN+SUB: the main and sub

 

sound of the audio track 1.

 

2: MAIN*: the main sound of the audio

 

track 2.

 

2: SUB*: the sub sound of the audio

 

track 2.

 

2: MAIN+SUB*: the main and sub

 

sound of the audio track 2.

 

*These items do not appear if only one audio stream is recorded on the disc being played back.

When playing a VIDEO CD, AUDIO CD, or MP3 audio track:

STEREO: the standard stereo sound.

1/L: the sound of the left channel (monaural).

2/R: the sound of the right channel (monaural).

When playing a Super VCD:

1: STEREO: the stereo sound of the audio track 1.

1: 1/L: the sound of the left channel of the audio track 1 (monaural).

1: 2/R: the sound of the right channel of the audio track 1 (monaural).

2: STEREO: the stereo sound of the audio track 2.

2: 1/L: the sound of the left channel of the audio track 2 (monaural).

2: 2/R: the sound of the right channel of the audio track 2 (monaural).

Continued 25GB

CMT-DH7BT.GB.3-097-195-11(1)

Playing VIDEO CDs with PBC functions (Version 2.0) PBC Playback

(VIDEO CD only)

You can use the PBC (Playback Control) menus on your TV screen to enjoy

the disc’s interactive software. The menu format and structure may differ depending on each disc.

1Press to start playing a VIDEO CD with PBC functions (Version 2.0).

The PBC menu appears on the TV screen. Depending on the VIDEO CD, the menu may not appear.

2Press the numeric buttons to select the item number you want.

3Press ENTER .

Depending on the VIDEO CD, “Press ENTER” may appear as “Press

SELECT” in the operating instructions

supplied with the disc. In this case, press .

4Continue playback according to the instructions on the menus.

Refer to the operating instructions supplied with the VIDEO CD, as the operating procedure may differ depending on the VIDEO CD.

To return to the previous menu

Press RETURN .

Note

PBC playback is canceled when Shuffle Play, Program Play or Repeat Play is activated.

To cancel playback with PBC functions

1Press or repeatedly or press the numeric buttons to select a track when playback is stopped.

2 Press or ENTER .

Playback starts from the selected track. Still images, such as the menu screens, will not be shown.

To return to PBC playback, press twice, then press .

Resuming playback from the point you stopped the disc Resume Play

This system memorizes the point where you stopped the disc so you can resume playback from that point. Resume Play is not canceled when you turn off the system except for MP3 audio tracks and JPEG image files.

1While playing a disc, press to stop playback.

“Resume” appears in the display.

2Press .

The system starts playback from the point you stopped the disc in step 1.

Notes

You cannot perform Resume Play during Shuffle Play or Program Play.

This function may not work properly with some discs.

Resume Play is canceled when

you press when playback is stopped.

you eject the disc.

you change the function.

you change the settings in the Setup Menu.

26GB

Depe the s the e

If “M Resu VID disc

Tip

To play press

Resu stopp

(DVD This s you st for up when you st 41st d the fir To act DISC to “O

Note

If “MU system such as point f

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

y

is

track.

reens,

t you

here ume lay e and

to

the p 1.

ng

ith

opped.

Depending on where you stopped the disc, the system may not resume playback from the exact same point.

If “MULTI-DISC RESUME” is set to “ON”, Resume Play is not canceled for DVD VIDEO and VIDEO CD when you eject the disc or change the function.

Tip

To play back from the beginning of the disc, press twice, then press .

Resuming playback of a disc that was stopped Multi-disc Resume

(DVD VIDEO and VIDEO CD only) This system can store the point where you stopped the playback of the disc for up to 40 discs and resumes playback when you insert the same disc again. If

you store a playback resume point for the 41st disc, the playback resume point for the first disc will be deleted.

To activate this function, set “MULTIDISC RESUME” in “CUSTOM SETUP” to “ON” (page 47).

Note

If “MULTI-DISC RESUME” is set to “ON”, the system may play back the next recorded disc such as a DVD-RW from the playback resume point for the current recorded disc.

Using play mode

Creating your own program

Program Play

You can make a program of up to 99 steps in the order you want them to be played back.

You can only program the tracks from the current disc.

1 Press DISPLAY .

The Control Menu appears on the TV screen.

2Press or repeatedly to

select (PROGRAM), then press ENTER .

The options for “PROGRAM” appear on the TV screen.

3Press or repeatedly to select “SET ”, then press ENTER .

Tracks number

Disc

Continued 27GB

CMT-DH7BT.GB.3-097-195-11(1)

4Press .

The cursor moves to the track row “T” (in this case, “01”).

To change a programmed step:

Press or repeatedly to select the programmed step number you want to change. Then, press .

To delete a programmed step:

Press or repeatedly to select the programmed step number

you want to change. Then, press CLEAR .

To delete all of the programmed steps in the program list:

Press to select “ALL CLEAR”. Then, press ENTER .

5Select the track you want to program.

For example, select track “02”. Press or repeatedly to

select “02” under “T”, then press ENTER .

Selected track

Total time of the programmed tracks

6To program other tracks, repeat steps 4 to 5.

7Press .

Program Play starts.

When the Program Play ends, you

can restart the same program by pressing .

To cancel Program Play

Press CLEAR or select “OFF” in step 3. To play back the same program again, select “ON” in step 3 and press ENTER or .

To turn off the Control Menu

Press DISPLAY repeatedly until the Control Menu disappears from the TV screen.

Notes

When Program Play is activated, the “REPEAT” setting is automatically changed to “ON” if the current setting is “DISC” or “TRACK”.

You cannot perform Program Play with VIDEO CDs during PBC playback.

Tip

The Program Play is canceled and the program list is cleared when

you eject the disc.

you turn off the system.

you change the function.

28GB

Play

Sh

You ca curren you p order Shuffl tracks

1Pr pl

Th scr

2Pr se pr

Th on

3Pr se

W AU

W

W

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

Loading...
+ 64 hidden pages