CDX-S1000/S2000/S2000C
SERVICE MANUAL
Ver 1.0 2003. 11
Photo: CDX-S2000
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AEP Model
UK Model
Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-611XA-186//Q
Optical Pick-up Name KSS1000E
CD player section
Signal-to-noise ratio 120 dB
Frequency response 10 – 20,000 Hz
Wow and flutter Below measurable limit
Tuner section
FM
Tuning range 87.5 – 108.0 MHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 9 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation 35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
AM (CDX-S1000)
Tuning range 531 – 1,602 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity AM: 30 µV
MW/LW (CDX-S2000/S2000C)
Tuning range MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW: 30 µV
LW: 40 µV
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 45 W × 4 (at 4 ohms) (CDX-S1000)
50 W × 4 (at 4 ohms) (CDX-S2000/S2000C)
General
Outputs Audio outputs (rear)
Power aerial relay control terminal
Power amplifier control terminal
Inputs Telephone ATT control terminal
Remote controller input terminal (CDX-S2000/S2000C)
Aerial input terminal
Tone controls Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
– Continued on next page –
FM/AM COMPACT DISC PLAYER
CDX-S1000
9-961-371-01
2003K04-1
© 2003. 11
FM/MW/LW COMPACT DISC PLAYER
CDX-S2000/S2000C
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
1
CDX-S1000/S2000/S2000C
Power requirements 12 V DC car battery
(negative ground)
Dimensions Approx. 178 × 50 × 176 mm
(w/h/d)
Mounting dimensions Approx. 182 × 53 × 161 mm
(w/h/d)
Mass Approx. 1.2 kg
Supplied accessories Parts for installation and connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
SERVICE NOTES
This label is located on the bottom of the chassis.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up
semi-fixed resistor
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY-RELATED COMPONENT WARNING!!
Notes on CD-R/CD-RW discs
•You can play CD-Rs (recordable CDs)/CD-RWs (re writable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
• Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
•You cannot play a CD-R/a CD-RW that is not finalized*.
*A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
z
D
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CDX-S1000/S2000/S2000C
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SER V O board (CN1)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301
J-2502-076-1
SERVO BOAR
CN1
3
CDX-S1000/S2000/S2000C
1. GENERAL
Location of controls................................................................. 5
Connections ............................................................................. 6
2. DISASSEMBLY
2-1. Sub Panel (1) Assy .............................................................. 7
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 8
2-4. Chassis (T) Sub Assy .......................................................... 9
2-5. Roller Arm Assy .................................................................. 9
2-6. Chassis (OP) Assy............................................................. 10
2-7. Optical Pick-up ................................................................. 10
2-8. SL Motor Assy (M902) .....................................................11
2-9. LE Motor Assy (M903)..................................................... 11
2-10. Servo Board....................................................................... 12
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 13
3-2. Block Diagram –CD Section–........................................... 17
3-3. Block Diagram –Tuner Section–....................................... 18
3-4. Block Diagram –Display Section–.................................... 19
3-5. Printed Wiring Boards –CD Mechanism Section–............ 21
3-6. Schematic Diagram –CD Mechanism Section– ................22
3-7. Printed Wiring Board –Main Section– .............................. 23
3-8. Schematic Diagram –Main Section (1/2)– ........................24
3-9. Schematic Diagram –Main Section (2/2)– ........................25
3-10. Printed Wiring Board –Key Section– ................................ 26
3-11. Schematic Diagram –Key Section–...................................27
3-12. IC Block Diagrams............................................................ 28
TABLE OF CONTENTS
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 30
4-2. Front Panel Section ........................................................... 31
4-3. CD Mechanism Section (1) ...............................................32
4-4. CD Mechanism Section (2) ...............................................33
4-5. CD Mechanism Section (3) ...............................................34
4-6. CD Mechanism Section (4) ...............................................35
5. ELECTRICAL PARTS LIST ........................................ 36
4
CDX-S1000/S2000/S2000C
SECTION 1
GENERAL
(CDX-S1000) (CDX-S2000/S2000C)
This section is extracted
from instruction manual.
5
CDX-S1000/S2000/S2000C
Connections
6
SECTION 2
s
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1. SUB PANEL (1) ASSY
(Page 7)
2-2. CD MECHANISM BLOCK
(Page 8)
CDX-S1000/S2000/S2000C
2-3. MAIN BOARD
(Page 8)
2-4. CHASSIS (T) SUB ASSY
(Page 9)
2-5. ROLLER ARM ASSY
(Page 9)
2-6. CHASSIS (OP) ASSY
(Page 10)
2-8. SL MOTOR ASSY (M902)
(Page 11)
2-7. OPTICAL PICK-UP
(Page 10)
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (1) ASSY
2-10. SERVO BOARD
(Page 12)
2-9. LE MOTOR ASSY (M903)
(Page 11)
1
two
screws
(+PTT 2.6
x
6)
3
two claws
4
sub panel (1) assy
2
two claw
7
CDX-S1000/S2000/S2000C
)
)
2-2. CD MECHANISM BLOCK
5
CD mechanism block
2
screw
(+PTT 2.6
x
6)
7
bracket (CD)
3
6
two
screws
(+PTT 2.6
x
4)
2-3. MAIN BOARD
1
three ground point screws
(+PTT 2.6
x
6)
4
CNP301
3
MAIN board
1
screw
(+PTT 2.6
2
two
screws
(+PTT 2.6
x
x
6
6
8
2-4. CHASSIS (T) SUB ASSY
2
two
screws
x
(+P 1.7
4
SENSOR board
2.2)
3
claw
CDX-S1000/S2000/S2000C
1
two
screws
(+P 1.7
x
2.2)
5
chassis (T) sub assy
2-5. ROLLER ARM ASSY
4
worm wheel (RA)
1
spring (RAL)
3
washer (1.0 – 2.5)
5
roller arm assy
2
spring (RAR)
9
CDX-S1000/S2000/S2000C
)
2-6. CHASSIS (OP) ASSY
0
compression spring (damper)
lever (D)
4
washer
5
gear (LE1)
6
8
qa
chassis (OP) assy
1
CN2
9
two compression springs (damper
7
2-7. OPTICAL PICK-UP
5
claw
2
Remove the six solderings.
slider (R)
3
torsion spring (SL)
2
chucking arm sub assy
1
tension coil spring (CHKG)
10
6
main shaft
7
optical pick-up
4
rack (SL)
3
screw
(+B 1.4
x
5)
2-8. SL MOTOR ASSY (M902)
CDX-S1000/S2000/S2000C
1
screw
(+P 1.4
x
1.8)
2-9. LE MOTOR ASSY (M903)
qf
two toothed lock
(+M 1.4
bracket (LEM)
qs
screw
(+M 1.7
x
)
screws
2.5)
qa
screw
(+M 1.7
qd
2
SL motor assy (M902)
0
woam (LEB) assy
x
2.5)
qg
LE motor assy
(M903)
8
screw
(+M 1.7
9
bearing (LEB)
2
washer
gear (LE1)
3
lever (D)
x
2.5)
4
5
6
screw
(+P 1.7
x
2.2)
7
leaf spring (LE)
1
Remove the soldering.
slider (R)
11
CDX-S1000/S2000/S2000C
2-10. SERVO BOARD
1
Remove the eight solderings.
6
SERVO board
2
Remove the three solderings.
4
toothed lock
(M 1.7)
5
claw
screw
3
CN2
12
CDX-S1000/S2000/S2000C
SECTION 3
DIAGRAMS
3-1. IC PIN DESCRIPTIONS
• IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No. Pin Name I/O Pin Description
1LDOLaser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
2PDIDimmer monitor input from optical pick-up laser diode.
3PNINot used. (Fixed at L in this set)
4AVDD — Analog power supply pin (+3.3 V)
5 DGND — Ground
6 RFOK O RFOK signal output to system control IC.
7 INTQ O CD text pack synchronization signal output to system control IC.
8 RST I CD reset signal input from system control IC.
9A0I
10 STB I Data strobe signal input from system control IC.
11 SCK I Serial clock input from system control IC.
12 SO O Serial data output to system control IC.
13 SI I Serial data input from system control IC.
14 DVDD — Power supply pin (+3.3 V)
15 DAVDD — D/A converter power supply (+) pin (+3.3 V)
16 ROUT O Analog audio signal output (R-ch)
17 DAGND — Ground
18 REGC — Capacitor connection pin for SCF regulator.
19 DAGND — Ground
20 LOUT O Analog audio signal output (L-ch)
21 DAVDD — D/A converter power supply (+) pin (+3.3 V)
22 XVDD — Power supply pin (+3.3 V)
23 XTAL O Main system clock output (16.9344 MHz)
24 XTAL I Main system clock input (16.9344 MHz)
25 XGND — Ground
26 DVDD — Power supply pin (+3.3 V)
27 C1D1/FZD O Not used. (Open)
28 C1D2/TZD O Not used. (Open)
29 C2D1/RMUTE O CD R-ch data zero detection signal output
30 C2D2/LMUTE O CD L-ch data zero detection signal output
31 C2D3/SHOCK/SBSY O Not used. (Open)
32 LOCK/FR O Not used. (Open)
33 WFCK/MIRR O Not used. (Open)
34 RFCK/HOLD O Not used. (Open)
35 PLCK O Not used. (Open)
36 C16M O Not used. (Open)
37 DGND — Ground
38 TX O Not used. (Open)
39 EMPH/RAMOVER O Not used. (Open)
40 FLAG O Not used. (Open)
41 DVDD — Power supply pin (+3.3 V)
42 LIMIT I Not used. (Fixed at L in this set)
43 XTALEN I
44 DGND — Ground
45 DIN I Not used. (Connect to DOUT in this set)
46 DOUT O Not used. (Connect to DIN in this set)
47 SCKIN I Not used. (Connect to SCKO in this set)
48 SCKO O Not used. (Connect to SCKIN in this set)
49 LRCKIN I Not used. (Connect to LRCK in this set)
Command/parameter discrimination signal input from system control IC.
(L: command transmission, H: parameter transmission)
Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
(Fixed at L in this set)
13
CDX-S1000/S2000/S2000C
Pin No. Pin Name I/O Pin Description
50 LRCK O Not used. (Connect to LRCKIN in this set)
51 DVDD — Power supply pin (+3.3 V)
52 FD+ O Focus servo drive PWM signal output (+)
53 FD– O Focus servo drive PWM signal output (–)
54 TD+ O Tracking servo drive PWM signal output (+)
55 TD– O Tracking servo drive PWM signal output (–)
56 SD+ O Sled servo drive PWM signal output (+)
57 SD– O Sled servo drive PWM signal output (–)
58 MD+ O Spindle servo drive PWM signal output (+)
59 MD– O Spindle servo drive PWM signal output (–)
60 DGND — Ground
61 TESTEN I Test setting input (Fixed at L in this set)
62 to 66 TEST4 to TEST0 I Test setting input (Fixed at L in this set)
67 ADGND — A/D converter power supply (–) pin
68 EFM O EFM signal output
69 ASY I EFM comparator reference voltage input
70 ADVDD — A/D converter power supply pin (+3.3 V)
71 RFI I RF signal input for EFM data growing.
72 EQ2 — Not used. (Open)
73 EQ1 — RF amplifier equalizer parts connection pin
74 RF– I Not used. (Open)
75 RF2– I RF amplifier inversion input
76 AGCO O RF signal output after on AGC.
77 AGCI I RF AGC signal amplifier input
78 RFO O RF signal output before on AGC.
79 ATEST I Not used. (Open)
80 C3T — Capacitor connection pin for 3T detection.
81 AGND — Ground
82 A I Signal input (A) from optical pick-up detector.
83 C I Signal input (C) from optical pick-up detector.
84 B I Signal input (B) from optical pick-up detector.
85 D I Signal input (D) from optical pick-up detector.
86 F I Signal input (F) from optical pick-up detector.
87 E I Signal input (E) from optical pick-up detector.
88 VREFIN I Reference voltage (+1.65 V) input
89 AVDD — Analog power supply pin (+3.3 V)
90 REFOUT O Reference voltage (+1.65 V) output
91 REFC — Capacitor connection pin for reference voltage output.
92 FE– I Focus error signal amplifier inversion input
93 FEO O Focus error signal amplifier output
94 ADCIN I Not used. (Open)
95 TE– I Tracking error signal amplifier inversion input
96 TEO O Tracking error signal amplifier before output
97 TE2 O Tracking error signal amplifier after output
98 TEC I Tracking error signal comparator input
99 AGND — Ground
100 PWMSW I Not used. (Fixed at L in this set)
14
CDX-S1000/S2000/S2000C
• IC501 MN101E01KDC (SYSTEM CONTROL) (MAIN BOARD (2/2))
Pin No. Pin Name I/O Pin Description
1DAVDD — D/A converter power supply (+) pin (+3.3 V)
2 NCO O Not used. (Open)
3DAVSS — D/A converter power supply (–) pin
4 UNISO O Not used. (Open)
5 UNISI I Not used. (Fixed at L in this set)
6 UNICKO O Not used. (Fixed at L in this set)
7 RETRA O Not used. (Open)
8, 9 NCO O Not used. (Open)
10 VDD1 — Power supply pin (+3.3 V)
11 MMOD I Not used. (Fixed at L in this set)
12 OSCOUT O Main clock output (27 MHz)
13 OSCIN I Main clock input (27 MHz)
14 VSS1 — Ground
15 XIN I Sub clock input (32.768 kHz)
16 XOUT O Sub clock output (32.768 kHz)
17 VDD2 — Power supply pin (+3.3 V)
18 MOD1 — Not used. (Fixed at H in this set)
19 RESET I Microcomputer reset input
20 RCIN1 I Rotary commander SHIFT key input
21 ACCIN I Accessory power supply detection input
22 TESTIN I Test mode detection input
23 TELATT I Telephone attenuator detection input
24 AT T O Audio mute control output
25 XKEYON O Key power supply control output
26 NCO O Not used. (Open)
27 KEYACK I Key ackno wledge detection input
28 TU_ATTIN I Mute zero cross detection input from tuner unit. (CDX-S2000/S2000C)
29, 30 NCO O Not used. (Open)
31 BUIN I Backup power supply detection input
32 CD_INTQ I CD text pack synchronization signal input from CD servo IC.
33 CD_SO O Serial data output to CD servo IC.
34 CD_SI I Serial data input from CD servo IC.
35 CD_SCK O Serial clock output to CD servo IC.
36 BUSON O Not used. (Fixed at H in this set)
37 SYSRST O Not used. (Fixed at H in this set)
38 CD_RFOK I RFOK signal input from CD servo IC.
39 CD_RST O Reset signal output to CD servo IC.
40 CD_A0 O Command/parameter discrimination signal output to CD servo IC.
41 CD_STB O Data strobe signal output to CD servo IC.
42 CD_MUTE-R I Mute zero cross detection input (R-ch) from CD mechanism deck.
43 CD_MUTE-L I Mute zero cross detection input (L-ch) from CD mechanism deck.
44 CD_INSW I Disc in switch detection input from CD mechanism deck.
45 CD_SELFSW I Self switch detection input from CD mechanism deck.
46 CD_LM_LO O Loading motor control output to CD mechanism deck. (Loading direction)
47 CD_LM_EJ O Loading motor control output to CD mechanism deck. (Eject direction)
48 CD_DSW I Down switch detection input from CD mechanism deck.
49 CD_LIMIT I Limit switch detection input from CD mechanism deck.
50 AMPATT O Not used. (Fixed at L in this set)
51 AREASEL2 O Not used. (Open)
52 AREASEL1 O Not used. (Open)
53 AREASEL0 I Destination area initial setting input (L: CDX-S1000, H: CDX-S2000/S2000C)
15
CDX-S1000/S2000/S2000C
Pin No. Pin Name I/O Pin Description
54 COL_SW I
55 to 57 NCO O Not used. (Open)
58 PANEL_SW I Front panel detach detection input (L: with front panel, H: without front panel)
59 DIAG I Mode input from power amp IC.
60 VOLATT O Attenuator control output to electronic volume IC.
61 NOSE-SW O Not used. (Open)
62 NCO O Not used. (Open)
63 VSS2 — Ground
64 TU-ATT O Tuner mute control output
65 NCO (TUNON) O Not used. (Open)
66 NS_MASK O Noise mask output (CDX-S2000/S2000C)
67 EEP_CKO O Serial clock output to EEPROM communication.
68 EEP_SIO I/O Serial data input/output with EEPROM communication.
69 DOOR-IND O Not used. (Open)
70 AMPSTB O Standby control output to power amp IC.
71 NCO O Not used. (Open)
72 LCDSO/FLS_SO O Serial data output to LCD driver IC.
73 LCDCE/FLS_SI O Chip enable output to LCD driver IC.
74 LCDCKO O Serial clock output to LCD driver IC.
75 to 78 NCO O Not used. (Open)
79 I2C_SIO I/O I2C bus serial data input/output
80 NCO O Not used. (Open)
81 I2C_CKO O I2C bus serial clock output
82 DAVN I RDS data block synchronization detection input (CDX-S2000/S2000C)
83 SIRCS I SIRCS signal input
84 NCO O Not used. (Open)
85 BEEP O Beep output to power amp IC.
86 to 88 NCO O Not used. (Open)
89 VDD3 — Power supply pin (+3.3 V)
90 NCO O Not used. (Open)
91 VSS3 — Ground
92 QUALITY I Noise detection input (CDX-S2000/S2000C)
93 VSM I S-meter voltage detection input
94, 95 KEYIN1, 0 I Key input 1, 0
96 RCIN0 I Rotary commander key input
97 to 99 NCO O Not used. (Open)
100 VREF+ — A/D converter power supply (+) pin (+3.3 V)
1 color/2 color select input (L (1 color): CDX-S1000/S2000,
H (2 color): CDX-S2000C)
16
3-2. BLOCK DIAGRAM — CD SECTION —
OPTICAL PICK-UP
(KSS1000E)
A
82
C
83
B
84
I-V
CONV.
PD
D
85
E
87
F
86
PD
2
TRACKING
ERROR
LD AMP
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
RF
EQ
FORCUS
ERROR
IC1
SERVO
CTL
EFM
DEMOD
D/A
CONV
I/F
(Page 18)
TUNER
LOUT
20
ROUT
16
INTQ
7 32
SI
13
SO
12
SCK
11
STB
10
A0
9
RST
8
RFOK
6
CDL
CDR
SECTION
CDX-S1000/S2000/S2000C
A
SYSTEM CONTROL
CD_INTQ
33
CD_SO
34
CD_SI
35
CD_SCK
41
CD_STB
40
CD_A0
39
CD_RST
38
CD_RFOK
IC501 (1/3)
LD
FOCUS
COIL
TRACKING
COIL
M902
(SLED)
M901
(SPINDLE)
M903
(LOADING)
LD
DRIVE
Q1
+-
M
+-
M
+-
M
LD
1
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
12
11
13
14
15
16
17
18
9
10
FSC
FSC
TRK
TRK
SL-
SL+
SP-
SP+
LD-
LD+
+
-
+
-
IC2
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
LOADING
MOTOR
DRIVE
FD+
TD+
TD-
SD+
SD-
MD+
MD-
LOAD
EJECT
FD-
27
26
24
23
28
OSC
FD+
FD-
TD+
TD-
SD+
SD-
MD+
MD-
52 53 54 55 56 57 58 59
5
6
2
3
1
A3.3V
AU3.3V
D3.3V
DR6V
SERVO 3.3V
MECH6V
23 24
X1
16.9344MHz
30 43
LMUTE
29 42
RMUTE
SW3
(DISC IN)
SW2
(SELF)
SW4
(LIMIT)
SW1
(DOWN)
CD_MUTE-L
CD_MUTE-R
44
CD_INSW
45
CD_SELFSW
CD_LIMIT
49
48
CD_DSW
CD_LM_LO
46
47
CD_LM_EJ
RESET
IC602
19
1
S702
(RESET)
RESET
3.3V
3
Signal path
: CD
17 17
CDX-S1000/S2000/S2000C
3-3. BLOCK DIAGRAM — TUNER SECTION —
TUNER UNIT
J1
(ANTENNA)
ANT
1
MUTE-CONDITION
TU-VDD (TU5V)
TU1
S-METER
TU-SDA
TU-SCL
QUALITY
E2P-SDA
E2P-SCL
TU-MUTE
VCC (8.3V)
L-CH
R-CH
RDS
SOUND CONTROL
ELECTRONIC VOLUME
IC401
BUS-LCH
5
NC
OUT
CHECK
Q581,582
OUT
-RL
-FL
23
MUTE
Q441
22
MUTE
Q461
MULTIPLE VOLTAGE
DIAG
25
OVER VOLTAGE
DET.
Q580,D580,581
BATT
CDL
9
CD-LCH
EFFECT
A
70
85
23
21
22
24
59
37
36
5
6
4
NC
31
INPUT SELECTOR
EVR
CONT.
BATT
3.3V
TONE
LINE MUTE
CONTROL
Q478,479
BACK-UP CHECK/
LOW VOLTAGE
CD
12
11
15
+5V REG.
Q1
CDR R-CH
3.3V
AUDIO 8.3V
TV-LCH
7
SDA
31
SCL
30
29
SYSTEM CONTROL
VOLATT
60
DAVN
82
VSM
93
I2C_SIO
79
81
I2C_CKO
QUALITY
92
NS-MASK
66
68
EEP_SIO
EEP_CKO
67
64
TU_ATT
28
TU_ATTIN
MUTE
IC501 (2/3)
I2C
BUS
AMPSTB
BEEP
TELATT
ACCIN
TESTIN
ATT
DIAG
SYSRST
BUSON
UNISI
UNICKO
UNISO
BUIN
(Page 17)
4
R-CH
3
S2000/S2000C
RDS DEMODULATOR
9
X51
8.664MHz
6
14
13
5
17
16
8
7
11
10
MPX
16
XTI
9
XTO
10
1 7
IC51
TU 5V REG
Q51,52
S2000/S2000C
NS MASK
SWITCH
S2000/S2000C
SECTION
SDA
SCL
INTN
Q22
12
11
STB
22
BEEP
16
SDA
2
SCL
4
ACC
CHECK
Q631
REGULATOR
IC750 (2/2)
AMP-REM
ANT-REM
PANEL+B
MECH 6V
SERVO 3.3V
AUDIO 8.3V
POWER AMP
IC750 (1/2)
MUTE
MUTE
CONT.
I2C
BUS
29
27
37
B.UP+B
34
33
31
30
35
VP
VP2
VP1
TEL
ATT
Q651
5
3
9
7
6
20
D759
D760
3.3V
PANEL+B
MECH 6V
SERVO 3.3V
AUDIO 8.3V
BATT
R-CH
R-CH
F901
10A
• Signal path
: FM
: CD
• R-ch is omitted due to same as L-ch.
CN601
19
17
18
-1
-2
1
9
2
10
4
12
3
11
13
7
15
5
6
8
16
L
R
FL+
FL-
RL+
RL-
FR+
FR-
RR+
RR-
ATT
ACC
TEST
ANP-R
ANT-R
GND
+B (BATT)
J330
AUDIO OUT REAR
1818
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
CDX-S1000/S2000/S2000C
KEY MATRIX
LSW900,903-905,
907-911,913-921
S901,902,906,912
S2000/S2000C
J561
(REMOTE IN)
PANEL +B
D502
D501
IC981
VLCD
CONTROL
KEY
ACTIVE
Q664
IC971
REMOTE
RECEIVER
2
X502
32.768kHz
SYSTEM CONTROL
IC501 (3/3)
KEYIN0
95
KEYIN1
94
KEYACK
27
XKEYON
25
RCIN1
20
RCIN0
96
1
SIRCS
83
XIN
15
XOUT
16
LCDSO
LCDCKO
LCDCE
OSCOUT
OSCIN
72
74
73
12
13
64
63
62
1
X501
27MHz
LCD DRIVER
DI
DATA
CL
CLK
CE
CE
ON/OFF
IC901
S1
|
S46
COM1
|
COM4
PANEL +B
PANEL +B
LED
CONTROL
Q901-903
S2000C
2
40
I
I
25
49
•
27
I
38
•
51
|
54
(LCD BACK LIGHT)
LSW900,903-905,
907-911,913-921
LED901,902,906,912,
951,952
()
LCD901
LED931,932
KEY
ILLUMINATION
S1000/S2000
LCD
19 19
CDX-S1000/S2000/S2000C
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
•%: indicates tolerance.
f
•
• C : panel designation.
Note: The components identified by mark 0 or dotted line
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
•Voltages are taken with a VOM (Input impedance 10 MΩ).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
for printed wiring boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
• : Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
: internal component.
with mark 0 are critical for safety.
Replace only with part number specified.
supply from ACC and BATT cords.
Voltage variations may be noted due to normal produc-
tion tolerances.
Voltage variations may be noted due to normal production tolerances.
F : FM
f : AM (CDX-S1000) or MW (CDX-S2000/S2000C)
J : CD
a
: Through hole.
(The other layer’s patterns are not indicated.)
4
W or less unless otherwise
• Waveforms
— Servo Board —
(MODE: CD PLAY)
1
16.9344MHz
wd
(XTAL)
IC1
2
uj
(AGCI)
IC1
3
Approx. 620mVp-p
od
(FEO)
IC1
4
Approx. 200mVp-p
oh
(TEO)
IC1
1.2Vp-p
1.6Vp-p
0V
0V
— Main Board —
1
8.664MHz
IC51 q; (XTO)
2
27MHz
IC501 qs (OSCOUT)
3
32.768kHz
IC501
(XOUT)
qh
2.1Vp-p
1.6Vp-p
2.2Vp-p
2020
3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 20 for Common Note for Printed Wiring Boards. : Uses unleaded solder.
CDX-S1000/S2000/S2000C
A
B
C
D
1
234567891011121314
C6
C5
JR91
JR90
JR40
C11
C13
JR41
R1
C8
X1
R42
C7
C17
R41
IC1
C3
R6
C19
R45
C2
R7
C18
C20
C21
R44
C1
C23
R9
C32
C27
C26
C25
C36
C31
C30
C28
R13
C39
C29
C38
Q1
R15
R11
R14
C34
R12
C37
C35
CN2
CN1
(Page 23)
E
F
G
H
R74
R72
R76
R77
R70
R73
R75
R71
C73
C71
C72
C75
C70
IC2
FB1
C78
C79
R83
C77
C76
C74
R85
R84
R81
R79
R82
R80
R78
SW1
M901
SW4
M902
M903
SW3
SW2
21 21
CDX-S1000/S2000/S2000C
3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 20 for Common Note on Schematic Diagram and Waveforms.
• Refer to page 28 for IC Block Diagrams.
C20
SW3
SW2
TP19
CN2
TP27
TP28
TP29
TP31
TP30
TP29
TP14
TP28
TP27
TP26
Q1
C36
R13
C37
R12
C35
C34
R11
SW4
M901
M902
SW1
TP81
TP80
TP85
TP83
TP84
TP82
TP87
TP88
TP89
TP90
TP91
TP33TP32
R15
R14
C38
C39
TP22
TP20
C26
TP21
C27
C28
TP23
C29
C1
TP25
C30
TP24
C31
C32
R9
C25
C23
C21
C2
C18
R7
R6
C19
IC1
C5
C3
C6
C7
C17
R1
C13
TP13
TP12
TP11
TP10
TP9
TP8
TP7
TP6
TP5
TP4
TP3
TP2
TP1
C11
JR90
JR91
X1
C8
FB1
R41
JR41
JR40
R42
TP65
TP64
TP63
TP62
TP61
TP60
TP59
R45
TP58
R44
TP57
TP56
TP55
TP54
TP48
TP52
TP51
TP53
TP49
TP50
TP47
TP46
TP45
TP44
TP43
TP42
TP41
TP40
CN1
(Page 25)
Note:
•Voltage is dc with respect to
ground under no-signal conditions.
no mark : CD PLAY
M903
TP92
TP93
C70
R71
R70
C71
R73
R72
R75
R74
R76
C72
C73
R77
TP100
C74
TP71
TP70
TP73
TP72
IC2
IC B/D
C79
R85
R84
R83
R82
C78
C77
R81
R80
C76
R79
R78
TP75
TP74
C75
2222
3-7. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder.
CDX-S1000/S2000/S2000C
A
B
C
D
E
F
G
H
1
JW101
JW100
R4
R5
R8
R9
C10
I
JW104
234567891011 12 13 14
J330
J561
CN601
JW12
JC501
D501
D758
C759
Q478
R479
IC750
JW11
R551
R550
R548
R549
C502
C513
JW10
JW24
R671
JW144
JW9
D757
D752
IC501
C518
R507
JW23
JW119
R565
JW82
R673
C764C765
JW6
D754
JW25
JW42
R528
R531
C770
R530
R547
R509
C504
C622
R527
JW8
D751
JW118
R571
C760
JC681
JW61
JW137
C509
R508
JW145
D753
JW55
R568
C515
JW146
JW134
JW26
JW98
R566
X501
C752
JW7
JW99
C508
R560
JW56
R543
JW5
D759
D760
C406
C407
R516
R506
JC503
C507
L304
R517
R572
JW45
X502
JW66
JW4
R652
L302
C302
R302
L307
R301
R672
C621
IC602
JW28
C308
C503
R651
R654
Q651
R559
R515
S702
JW29
JW27
JW141
R653
R525
JW49
F901
JW48
JW62
JW60
CNP301
JW65
R523
JW47
JW63
JW64
D651
D761
JW3
C617
C618
R526
JW51
R636
D762
R524
R563
C306
JW52
R584
C517
R674
R609
D609
C343
JW53
R564
JW30
C307
C305
R539
Q664
C301
L305
L306
C303
JW46
JW39
JW111
JW115
JW50
R541
JW44
JW31
JW32
L303
L301
R633
Q631
R634
R536
R535
JW41
JW109
R540
D601
JW117
R585
JW58
C601
C602
JW113
JW106
JW107
R631
JW1
JW2
C631
JW116
R632
L562
JW33
JW43
JW57
JW37
JW36
L601
R582
D580
R583
D581
Q580
Q582
Q581
JW136
L561
L563
(Page 21)
• Semiconductor Location
Ref. No. Location
D1 F-3
D479 E-6
D501 I-6
D502 I-5
D580 F-11
D581 F-11
D601 D-10
D609 D-9
D651 D-8
D710 I-3
D711 I-3
D712 I-2
D715 I-4
D716 I-3
D717 I-3
D718 I-3
D719 I-4
D720 I-3
D751 D-7
D752 D-6
D753 D-7
D754 D-6
D755 C-5
D756 C-5
D757 C-6
D758 C-6
D759 D-8
( ): CDX-S2000/S2000C only
J1
TU1
Q22
R29
C1
C2
C12
C13
R2
R3
C7
C51
R51
R52 R53
R54
JW105
C55
JW138
C56
C53
C57
C58
JC1
R11
JW94
D712
C11
JW102
R10
C3
C4
C5
R7
R6
C62
C54
JW143
IC51
JW78
JW77
D711
D710
JW110
R1
C6
Q1
R60 R61
Q51
JW139
JW142
D1
C60
R55
C59
D720
C332
C333
JC331
R433
R463
JW91
JW83
C442
R451
JW75
R706
R432R442
C461
C451
JC401
C413
R406
R408
R462
R405
JW73
JW127
D719
Q431
C753
JW70
R452
JW90
JW81
JW80
C432
JW71
R513
R514
Q461
Q451
JW132
C412
JW89
JW88
JW124
JW133
JW112
JW128
Q441
R443
R431
R453
JC461
JC451
R441
C401
C404C405
L1
JW79
JW54
Q52
R58
R56
D717D718
D716
X51
R59
R57
JW72
C441
C431
JW86
JW126
R705
R461
IC401
JW129
JW130
JW84
JW85
C756
R756
JW76
D715
C763
C758
JW131
JW123
JW74
JW14
JW15
JW16
JW17
R532
R534
JW122
R512
JW140
R502
R504
R505
C751 C771
JW18
C761
JW20
R407
R409
C755
C754
JW92
R522
R521
R570
JW121
R510
R511
R558
C511
JW68
R503
Q479
JW93
R518
JW22
C479
JW120
C501
C452
D755
JW59
R752
R501
C512
C514
D502
JC753
JW13
C462
D756
C769
C750
C623
D479
JW95
JW96
JW97
R557
R544
R567
C510
C516
JW125
Ref. No. Location
D760 D-8
D761 D-9
D762 D-9
(IC51) G-3
IC401 E-4
IC501 H-6
IC602 H-8
IC750 B-6
Q1 F-3
(Q22) D-2
(Q51) G-3
(Q52) G-3
Q431 B-4
Q441 B-3
Q451 D-4
Q461 C-4
Q478 E-6
Q479 E-5
Q580 G-11
Q581 G-11
Q582 G-11
Q631 H-10
Q651 D-8
Q664 H-9
J
CN701
(Page 26)
23 23
CDX-S1000/S2000/S2000C
3-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 20 for Common Note on Schematic Diagram and Waveforms.
• Refer to page 28 for IC Block Diagrams.
C413
C412
Q51
R60
R61
IC B/D
Q52
C10
C53
C55
C54
IC51
C62
R58
R431
C431
R432
R442
C441
R441 R443
R451
C451
R452
R462
C461
R461 R463
JC461
R52R51
C57
C56
R53
R57
R56
Q431
Q441
Q451
Q461
C51
C58
R54
C751
C752
C750
IC B/D
R55
X51
C59
C60
R433
C432
C442
R453
C452
JC451
JC331
C462
C753
JC753
R752
Q478
C765 C764
C754
C756
C755
R756
Q479
D479
C479
IC750
R479
C769
C759
C770
C760
C771
C761
C758
C763
D759
D761
D760 D762
D751
D752
R651
R652
D753
D754
D755
D756
D757
D758
R609
D609
C602
C601
C618C617
D601
CN601
F901
L601
TU1
J1
JC1
C3
R5
R4
C1
C2
R6
R7
R11
R10
C7
R3
R2
R59
C5
Q1
R1
C6 C12C13
D1
R8
Q22
R9
C4
R29
L1
IC B/D
JC401
C11
C401
C404
C405
C406
C407
IC401
R405
R406
R407
R408
R409
Note:
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(): AM or MW
<>: CD PLAY
(Page 25)
C332
C333
J330
2424
3-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 20 for Common Note on Schematic Diagram and Waveforms.
(Page 24)
(Page 22)
CNP301
C301
C343
L305
L306
L301
L303
C303
C305
C307
C306
C308
R302
R301
C302
L307
L304
L302
JC681
CDX-S1000/S2000/S2000C
R557
R532
R534
R507
C518
R550
R544
R548
R510
R549
R511
R551
R512
R559
R530
R528
R560
R571
R572
R527
R526
R523
R525
R524
IC501
R540
R541
R516
R515
R539
R568
R517
C509
R506
X502
R563
R566
R509
R564
C504
R565
C515
C508
C507
R547
R508
R543
R536
R535
C503
C517
R531
X501
Q664
R570
R705
R706
S702
R636
Q582
R584
Q631
R585
C621
IC602
Q651
R634
JC503
R633
C631
Q581
R654
C623
C622
R653
R632
Q580
D651
CN701
R631
D580 R582
D581
R583
(Page 27)
R558
C516
C510
C501
C511
R567
R501
R502
R503
R504
R505
C513
R518
R522
R514R513
C516
R521
C512
C502
D502
D501
C514
JC501
R672
R671
R673
D715
D719
D716
R674
D717
D718
D720
D710
D711
D712
L562
L563
L561
J561
Note:
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(): AM or MW
<>: CD PLAY
25 25
CDX-S1000/S2000/S2000C
3-10. PRINTED WIRING BOARD — KEY SECTION — • Refer to page 20 for Common Note on Printed Wiring Boards. : Uses unleaded solder.
A
B
C
D
1
LSW903
LSW904
LSW905
234567891011121314
R967
R904
LED952
R957
R958
R905
R959
LED902
R961
R963
R903
S902
R962
R906
LED906
S906
R902
R908
R907
LSW907
LSW908
LED932
R909
R955
LSW909
R956
R953
LSW921
R921
R954
LCD901
R920
LSW920
R951
R919
R952
LSW919
R918
R948
LSW918
R949
R917
LSW917
R916
LSW916
LED931
LSW915
R915
R914
LSW914
LSW913
LED951
R937
R938
R939
LED901
S901
LED912
S912
R932
R941
R943
R933
R942
R931
LSW900
LSW910
R901
LSW911
IC971
E
F
G
H
J
(Page 23)
C992
C993
Q902
R929
C973
C972
D903
Q903
R980
R924
R925R926
• Semiconductor Location
Ref. No. Location
D901 G-11
D902 G-11
(D903) G-4
D981 G-9
D991 H-13
IC901 G-7
IC971 D-13
IC981 G-10
LED901 C-12
( ): CDX-S2000C only
R928
R927
R976
R977
Ref. No. Location
LED902 D-2
LED906 C-3
LED912 C-13
LED931 C-11
LED932 C-4
LED951 A-12
LED952 A-2
(Q901) G-3
(Q902) G-5
(Q903) G-4
R966
R965
R964
Q901
R969
R968
R979
R970
R978
I
R984
R985
R986
R996
R995
IC901
R994
C991
C996
C995
R993
D981
R947
R992
C994
R997
R945R946
R991
R944
IC981
C982
R998
D902
C981
D901
CN901
R983
R982
R981
R971
R987
R988
R989
R936
R935
R934
R972
D991
C971
R913
R912
R911
2626
3-11. SCHEMATIC DIAGRAM — KEY SECTION — • Refer to page 20 for Common Note on Schematic Diagram.
R924
R925
R926
LSW900(2/2)
LED931
LSW910(2/2)
LSW911(2/2)
LED932
R931
R932
R933
R970
R934
R935
R936
LED951
LED912
LED901
R937
R938
R939
LSW913(2/2) LSW920(2/2)
R941
LSW914(2/2) LSW919(2/2)
R942
LSW915(2/2) LSW918(2/2) LSW909(2/2)
R943
LSW916(2/2)
R944
R945
R946
R947
R948 R953
R949 R954
LSW917(2/2) LSW921(2/2) LED902
LSW907(2/2)
R951
LSW908(2/2)
R952 R955
R956
LED952 LSW904(2/2)
R961
R957
R958
R959
LED906
R962
R963
R977
LSW903(2/2)
LSW905(2/2)
R976
R964
R965
R966
R967
R968
R969
R979
CDX-S1000/S2000/S2000C
R987
R988
R989
R998
R972
R993
C994
C991
R992
IC971
C992
C993
R984
R986
R985
R994
R995
R996
IC901
IC981
C982
C981 C971
R997
R980
D991
R991
D981
C996
C995
R927
R928
Q903
D903
C972
Q901Q902
R978
C973
R929
(Page 25)
CN901
D902
R971
R981
R982
R983
D901
LSW900(1/2)
S901
S902
LSW903(1/2)
LSW904(1/2)
LSW905(1/2)
S906
LSW907(1/2)
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
R901
R902
R903
R904 R914
R905
R906
R907
R908
R909
LSW911(1/2)
LSW913(1/2)
LSW914(1/2)
LSW915(1/2)
LSW916(1/2)
LSW917(1/2)
LSW918(1/2)
LSW919(1/2)
LSW920(1/2)
LSW921(1/2)
S912
R911
R912
R913
R915
R916
R917
R918
R919
R920
R921
LCD901
27 27
Note:
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
CDX-S1000/S2000/S2000C
3-12. IC BLOCK DIAGRAMS
IC2 BA5966FP-FE2
REV
OPIN4(+)
OPIN4(–)
2728 26 25
+–
LOADING DRIVER
REV
OUT F
FWD
OUT R
+–+–
FWD
OPIN1(+)
OPIN1(–)
OPOUT4
OPIN3(+)
OPIN3(–)
OPIN2(–)
OPOUT3
–
+
+
–
OPOUT2
24 23 22 21 20 19 18 17 16 15
+–
–
+
+
–
4 5 6 7 8 9 10 11 12 13 1421 3
OPOUT1
OPIN2(+)
MUTE
VCC
MUTE
VCC
BIAS
VOL(–)
GND
VOL(+)
VO3(–)
VO3(+)
+–
+–
+
–
LEVEL
SHIFT
LEVEL
SHIFT
–+
+–
+–
VO2(–)
VO2(+)
VO4(–)
+–
–
LEVEL
SHIFT
LEVEL
SHIFT
–
+–
VO1(–)
+
+
VO4(+)
+–
+–
VO1(+)
IC401 BD3808FS-FE2
DGND
SDA
SCL
MUTE
SEL
ADJ
VCC
OUTF1
32 31 30 29 28 27 26 25 24 23 22
VCC
2
I
C BUS
LOGIC
BASS
fo:60,70,80,100,120,140,160,200Hz
Q:0.5,0.75,1,1.25
MIDDLE
fo:500Hz,1kHz
Q:1
TABLE
fo:5,7.5,10,12.5kHz
VCO
FADER
(0~-58,
-∞dB)
EFFECT (0dB~
+20dB,2dB STEP)
TONE
PASS
(+23~-79dB,-∞dB
fc:40kHz fc:40kHz
FADER
(0~-58,
-∞dB)
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
VOLUME
1dB STEP)
ANTI-ALIASING
FILTER
OUTR1
+20dB,2dB STEP)
TONE
PASS
OUTF2
OUTR2
FADER
(0~-58,
-∞dB)
EFFECT (0dB~
FADER
(0~-58,
-∞dB)
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
VOLUME
(+23~-79dB,-∞dB
1dB STEP)
ANTI-ALIASING
FILTER
DS12
DS22
DS32
21 20 19 18 17
2ND ORDER LPF
fc:OFF,80,120,160Hz
Q: 0.707
MIX
OUTS1
GAIN+ATT
(+10~-29,
-∞dB)
2ND ORDER
OUTS2
LPF
IC51 TDA7333-013TR (CDX-S2000/S2000C)
RDSREG
BAND PASS
FILTER
RAM
BUFFER
&
CONTROL
LOGIC
VDDA
REF3
REF2
REF1
VSS
VDDD
RESETN
INTERPOLATOR
1
2
3
4
5
6
TM
7
8
INTN
MPX
RDS
DEMODULATOR &
SYNCHRONIZATION
INPUT GAIN
(0~15dB,1dB STEP)
MUTE
INPUT SELECTOR
(4 STEREO INCLUDE 1 ISOLATION INPUT)
AGND
VCC/2
6 7 8 9 10 113 4 521
B2
AP1
AN
FIL
AP2
B1
C1
3
SDAOUT
SDAIN
SCK
SPI
TESTREG
SIGMA DELTA
CONVERTER
TEST LOGIC
&
PIN MUX'S
OSCILLATOR
16
MPX
15
INTN
14
CSN
13
SA_DATAOUT
12
SDA_DATAIN
11
SCL_CLK
10
XTO
9
XTI
SINC4
FILTER
SINC4REG
I2C/SPI
INTERFACE
2
INPUT GAIN
(0~15dB,1dB STEP)
MUTE
C2
D1
D2
12 14 1613 15
DS11
DS21
DS31
NC
NC
2828
IC750 TDA8588BJ/N2 (CDX-S2000/S2000C)
IC750 TDA8589BJ/N2 (CDX-S1000)
TAB
1
OUT-FL-
3
PROTECTION/
DIAGNOSTIC
FL
RL
MUTE
MUTE
RR
OUT-FL+
OUT-RL-
OUT-RL+
IN-RL
S-GND
IN-RR
OUT-RR+
OUT-RR-
5
7
9
11
13
15
17
19
CDX-S1000/S2000/S2000C
2
SDA
I2C BUS
4
SCL
6
VP2
8
PGND3
10
SVR
IN-FL
12
14
IN-FR
16
VP
BEEP
18
PGND2
OUT-FR+
OUT-FR-
DIAG
ANT-REM
AMP-REM
SERVO5V
MECH6V
B.UP+B
VP
21
23
25
27
29
31
33
35
37
CHIP DETECT/
DIAGNOSTIC
SWITCH
SWITCH
REFERENCE
DETECTION
VOLTAGE
FR
BATTERY
STANDBY/
MUTE
TEMPERATURE
PROTECTION
LOADDUMP
PROTECTION
ENABLE
LOGIC
REGULATOR
BACK-UP
SWITCHREGULATOR
20
22
24
26
28
30
32
34
36
VP1
STB
PGND1
RST
CRES
AUDIO8.3V
GND
PANEL+B
CBU
29
CDX-S1000/S2000/S2000C
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
4-1. MAIN SECTION
SECTION 4
EXPLODED VIEWS
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
Parts Color Cabinet’s Color
• Accessories are given in the last of this parts list.
R
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
A
not supplied
#1
A
MG-611XA-186//Q
B
4
3
#1
#2
not supplied
7
F901
#1
6
5
TU1
not supplied
B
2
#1
Ref. No. Part No. Description Remark
1 X-3384-176-1 PANEL ASSY, SUB
2 3-042-244-11 SCREW (T)
3 X-3383-739-1 LOCK ASSY (S)
4 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT
5 A-3283-361-A MAIN BOARD, COMPLETE (S2000)
5 A-3283-365-A MAIN BOARD, COMPLETE (S1000)
5 A-3283-366-A MAIN BOARD, COMPLETE (S2000C)
30
#1
1
Ref. No. Part No. Description Remark
6 3-246-481-01 PLATE (TU), GROUND
7 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
TU1 A-3220-959-A TUNER UNIT (TUX-032//Q)
#1 7-685-792-09 SCREW +PTT 2.6X6 (S)
#2 7-685-790-01 SCREW +PTT 2.6X4 (S)
4-2. FRONT PANEL SECTION
58
LCD901
not supplied
CDX-S1000/S2000/S2000C
57
#3
#3
not
supplied
51
55
not
supplied
60
not
supplied
59
54
not
supplied
not supplied
54
56
not supplied
(KEY board)
52
not supplied
53
51 X-3384-177-1 PANEL SUB ASSY, FRONT (S2000)
51 X-3384-185-1 PANEL SUB ASSY, FRONT (S1000)
51 X-3384-187-1 PANEL SUB ASSY, FRONT (S2000C)
52 X-3383-959-1 BUTTON ASSY (S) (S1000)
52 X-3384-178-1 BUTTON ASSY (S) (S2000/S2000C)
53 3-246-463-01 FILTER (IR)
54 3-246-466-01 PLATE (CD), LIGHT GUIDE
55 3-246-479-01 SPRING (RELEASE)
56 3-246-454-03 PANEL (CD), FRONT BACK
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
57 X-3383-264-2 CASE ASSY (for FRONT PANEL)
58 A-3372-468-A PANEL OVERALL ASSY, FRONT (S2000)
58 A-3372-474-A PANEL OVERALL ASSY, FRONT (S1000)
58 A-3372-480-A PANEL OVERALL ASSY, FRONT (S2000C)
59 1-694-977-11 CONDUCTIVE BOARD, CONNECTION
60 3-251-320-01 EMBLEM (NO.2.5), SONY (S2000C)
LCD901 1-805-078-11 DISPLAY PANEL, LIQUID CRYSTAL
#3 7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
31
CDX-S1000/S2000/S2000C
4-3. CD MECHANISM SECTION (1)
(MG-611XA-186//Q)
109
not supplied
102
not supplied
(SENSOR board)
110
not supplied
103
101
#4
104
106
105
108
107
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 A-3372-444-A CHASSIS (T) SUB ASSY
102 3-253-729-11 SPRING (LTR), TENSION COIL
103 3-257-892-11 SPRING (DAMPER), COIL
104 3-257-892-01 SPRING (DAMPER), COIL
105 3-253-695-11 SPRING (KF), TENSION COIL
106 3-259-033-01 DAMPER (S)
107 3-352-758-31 SCREW (M1.7), TOOTHED LOCK
108 A-3283-339-A SERVO BOARD, COMPLETE
109 X-3384-088-1 LEVER (L) ASSY
110 X-3384-089-1 LEVER (R) ASSY
#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
32
4-4. CD MECHANISM SECTION (2)
(MG-611XA-186//Q)
154
(including M901)
CDX-S1000/S2000/S2000C
155
156
157
#5
SW4
151
not supplied
M902
not supplied
not supplied
not supplied
153
not supplied
152
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 A-3372-445-A CHASSIS (OP) COMPLETE ASSY
152 4-912-432-01 SCREW (B1.4X5), TAPPING
0 153 8-820-207-02 OPTICAL PICK-UP KSS1000E/K1RP
154 A-3372-448-A CHASSIS (OP) SUB ASSY (including M901)
155 A-3372-449-A ARM SUB ASSY, CHUCKING
156 A-3372-446-A LEVER (SL) SUB ASSY
157 X-3384-090-1 LEVER (SL) ASSY
M902 A-3372-447-A MOTOR ASSY, SL (SLED)
SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
#5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8
33
CDX-S1000/S2000/S2000C
4-5. CD MECHANISM SECTION (3)
(MG-611XA-186//Q)
209
207
208
201
202
207
#4
M903
210
206
207
203
211
204
205
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 3-338-647-31 WASHER (1.0-2.5)
202 3-259-024-01 WHEEL (RA), WORM
203 A-3372-441-A ARM ASSY, ROLLER
204 3-259-455-11 SPRING (RAL)
205 3-253-713-11 SPRING (RAR)
206 3-259-469-11 SPRING (LE), LEAF
207 2-134-636-21 SCREW (M1.7X2.5)
208 3-259-467-11 BRACKET (LEM)
209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK
210 A-3372-450-A WORM (LEB) ASSY
211 3-259-468-11 BEARING (LEB)
M903 A-3372-443-A MOTOR ASSY, LE (LOADING)
#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
34
4-6. CD MECHANISM SECTION (4)
(MG-611XA-186//Q)
252
CDX-S1000/S2000/S2000C
254
252
255
256
251
253
257
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 3-259-429-11 WHEEL (LE), WORM
252 3-344-223-01 WASHER
253 3-259-470-11 GEAR (LE1)
254 3-253-755-11 LEVER (D)
255 3-899-829-01 WASHER (SLIT)
256 3-259-032-01 GEAR (LE2)
257 A-3337-998-A CHASSIS (M) BLOCK ASSY
35
CDX-S1000/S2000/S2000C
SECTION 5
KEY
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
KEY BOARD
**********
1-694-977-11 CONDUCTIVE BOARD, CONNECTION
< CAPACITOR >
C971 1-135-834-11 CERAMIC CHIP 2.2uF 6.3V
C972 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C973 1-135-834-11 CERAMIC CHIP 2.2uF 6.3V
C981 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C982 1-135-834-11 CERAMIC CHIP 2.2uF 6.3V
ELECTRICAL PARTS LIST
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
LED906 6-500-509-01 LED CL-165D/PG-D-T (MODE) (S2000C)
LED912 6-500-450-01 LED CL-195SR-CD-T (EQ3) (S1000/S2000)
LED912 6-500-509-01 LED CL-165D/PG-D-T (EQ3) (S2000C)
LED931 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT R)
LED932 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT L)
LED951 6-500-450-01 LED CL-195SR-CD-T (DISC IND R)
(S2000C)
(S2000C)
LED951 6-500-509-01 LED CL-165D/PG-D-T (DISC IND R) (S2000C)
LED952 6-500-450-01 LED CL-195SR-CD-T (DISC IND L)
LED952 6-500-509-01 LED CL-165D/PG-D-T (DISC IND L) (S2000C)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
(S1000/S2000)
(S1000/S2000)
< SWITCH >
C991 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C992 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C993 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C994 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C995 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C996 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR >
CN901 1-794-312-11 PIN, CONNECTOR 12P
< DIODE >
D901 8-719-085-72 DIODE UMZ6.8ENTR
D902 8-719-083-66 DIODE UDZS-TE17-18B
D903 8-719-072-70 DIODE MA2ZD14001S0 (S2000C)
D981 8-719-404-50 DIODE MA111-TX
D991 8-719-069-54 DIODE UDZS-TE17-5.1B
< IC >
IC901 6-705-180-01 IC LC75827W
IC971 6-600-163-01 IC RS-770 (IR)
IC981 6-705-374-01 IC MM3033DULE
< LIQUID CRYSTAL DISPLAY >
LCD901 1-805-078-11 DISPLAY PANEL, LIQUID CRYSTAL
< DIODE >
LED901 6-500-450-01 LED CL-195SR-CD-T (OFF) (S1000/S2000)
LED901 6-500-509-01 LED CL-165D/PG-D-T (OFF) (S2000C)
LED902 6-500-450-01 LED CL-195SR-CD-T (SOURCE)
(S1000/S2000)
LED902 6-500-509-01 LED CL-165D/PG-D-T (SOURCE) (S2000C)
LED906 6-500-450-01 LED CL-195SR-CD-T (MODE) (S1000/S2000)
LSW900 1-771-883-31 SWITCH, TACTILE (WITH LED) (Z)
(S1000/S2000)
LSW900 1-786-673-31 SWITCH, TACTILE (WITH LED) (Z) (S2000C)
LSW903 1-771-883-31 SWITCH, TACTILE (WITH LED) (SEL)
(S1000/S2000)
LSW903 1-786-673-31 SWITCH, TACTILE (WITH LED) (SEL) (S2000C)
LSW904 1-771-883-31 SWITCH, TACTILE (WITH LED) (+ (VOLUME))
(S1000/S2000)
LSW904 1-786-673-31 SWITCH, TACTILE (WITH LED) (+ (VOLUME))
(S2000C)
LSW905 1-771-883-31 SWITCH, TACTILE (WITH LED) (– (VOLUME))
(S1000/S2000)
LSW905 1-786-673-31 SWITCH, TACTILE (WITH LED) (– (VOLUME))
(S2000C)
LSW907 1-771-883-31 SWITCH, TACTILE (WITH LED) (ATT) (S1000)
LSW907 1-771-883-31 SWITCH, TACTILE (WITH LED) (AF) (S2000)
LSW907 1-786-673-31 SWITCH, TACTILE (WITH LED) (AF) (S2000C)
LSW908 1-771-883-31 SWITCH, TACTILE (WITH LED) (BTM) (S1000)
LSW908 1-771-883-31 SWITCH, TACTILE (WITH LED) (ATT) (S2000)
LSW908 1-786-673-31 SWITCH, TACTILE (WITH LED) (ATT) (S2000C)
LSW909 1-771-883-31 SWITCH, TACTILE (WITH LED) (SENS) (S1000)
LSW909 1-771-883-31 SWITCH, TACTILE (WITH LED) (SENS/BTM)
(S2000)
LSW909 1-786-673-31 SWITCH, TACTILE (WITH LED) (SENS/BTM)
(S2000C)
LSW910 1-771-883-31 SWITCH, TACTILE (WITH LED) (SEEK +/
>/M) (S1000/S2000)
LSW910 1-786-673-31 SWITCH, TACTILE (WITH LED) (SEEK +/
>/M) (S2000C)
LSW911 1-771-883-31 SWITCH, TACTILE (WITH LED) (m/./
SEEK –) (S1000/S2000)
LSW911 1-786-673-31 SWITCH, TACTILE (WITH LED) (m/./
SEEK –) (S2000C)
LSW913 1-771-883-31 SWITCH, TACTILE (WITH LED) (REP) (S1000)
36
CDX-S1000/S2000/S2000C
KEY
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
LSW913 1-771-883-31 SWITCH, TACTILE (WITH LED) (TA) (S2000)
LSW913 1-786-673-31 SWITCH, TACTILE (WITH LED) (TA) (S2000C)
LSW914 1-771-883-31 SWITCH, TACTILE (WITH LED) (SHUF) (S1000)
LSW914 1-771-883-31 SWITCH, TACTILE (WITH LED) (DSPL) (S2000)
LSW914 1-786-673-31 SWITCH, TACTILE (WITH LED) (DSPL)
(S2000C)
LSW915 1-771-883-31 SWITCH, TACTILE (WITH LED) (DSPL) (S1000)
LSW915 1-771-883-31 SWITCH, TACTILE (WITH LED) (PTY) (S2000)
LSW915 1-786-673-31 SWITCH, TACTILE (WITH LED) (PTY) (S2000C)
LSW916 1-771-883-31 SWITCH, TACTILE (WITH LED) (6)
(S1000/S2000)
LSW916 1-786-673-31 SWITCH, TACTILE (WITH LED) (6) (S2000C)
LSW917 1-771-883-31 SWITCH, TACTILE (WITH LED) (5)
(S1000/S2000)
LSW917 1-786-673-31 SWITCH, TACTILE (WITH LED) (5) (S2000C)
LSW918 1-771-883-31 SWITCH, TACTILE (WITH LED) (4) (S1000)
LSW918 1-771-883-31 SWITCH, TACTILE (WITH LED) (4/SHUF)
(S2000)
LSW918 1-786-673-31 SWITCH, TACTILE (WITH LED) (4/SHUF)
(S2000C)
LSW919 1-771-883-31 SWITCH, TACTILE (WITH LED) (3) (S1000)
LSW919 1-771-883-31 SWITCH, TACTILE (WITH LED) (3/REP) (S2000)
LSW919 1-786-673-31 SWITCH, TACTILE (WITH LED) (3/REP)
(S2000C)
LSW920 1-771-883-31 SWITCH, TACTILE (WITH LED) (2)
(S1000/S2000)
LSW920 1-786-673-31 SWITCH, TACTILE (WITH LED) (2) (S2000C)
LSW921 1-771-883-31 SWITCH, TACTILE (WITH LED) (1)
(S1000/S2000)
LSW921 1-786-673-31 SWITCH, TACTILE (WITH LED) (1) (S2000C)
< TRANSISTOR >
Q901 8-729-901-87 TRANSISTOR 2SC2411K-CQ (S2000C)
Q902 8-729-901-87 TRANSISTOR 2SC2411K-CQ (S2000C)
Q903 8-729-923-22 TRANSISTOR 2SD2114K (S2000C)
R926 1-216-805-11 METAL CHIP 47 5% 1/10W
R927 1-216-847-11 METAL CHIP 150K 5% 1/10W
(S2000C)
R928 1-216-847-11 METAL CHIP 150K 5% 1/10W
(S2000C)
R929 1-216-849-11 METAL CHIP 220K 5% 1/10W
(S2000C)
R931 1-216-809-11 METAL CHIP 100 5% 1/10W
R932 1-216-809-11 METAL CHIP 100 5% 1/10W
R933 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
R933 1-216-809-11 METAL CHIP 100 5% 1/10W
(S1000/S2000)
R934 1-216-811-11 METAL CHIP 150 5% 1/10W
(S2000C)
R935 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
R936 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
R937 1-216-811-11 METAL CHIP 150 5% 1/10W
(S2000C)
R937 1-216-817-11 METAL CHIP 470 5% 1/10W
(S1000/S2000)
R938 1-216-809-11 METAL CHIP 100 5% 1/10W
(S1000/S2000)
R938 1-216-813-11 METAL CHIP 220 5% 1/10W
(S2000C)
R939 1-216-807-11 METAL CHIP 68 5% 1/10W
(S1000/S2000)
R939 1-216-813-11 METAL CHIP 220 5% 1/10W
(S2000C)
R941 1-216-811-11 METAL CHIP 150 5% 1/10W
(S2000C)
R942 1-216-805-11 METAL CHIP 47 5% 1/10W
(S2000C)
R943 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
< RESISTOR >
R901 1-216-819-11 METAL CHIP 680 5% 1/10W
R902 1-216-819-11 METAL CHIP 680 5% 1/10W
R903 1-216-819-11 METAL CHIP 680 5% 1/10W
R904 1-216-821-11 METAL CHIP 1K 5% 1/10W
R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R906 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R907 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R908 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R909 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R911 1-216-819-11 METAL CHIP 680 5% 1/10W
R912 1-216-819-11 METAL CHIP 680 5% 1/10W
R913 1-216-819-11 METAL CHIP 680 5% 1/10W
R914 1-216-821-11 METAL CHIP 1K 5% 1/10W
R915 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R916 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R917 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R918 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R919 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R920 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
R921 1-216-833-11 METAL CHIP 10K 5% 1/10W
R924 1-216-809-11 METAL CHIP 100 5% 1/10W
R925 1-216-807-11 METAL CHIP 68 5% 1/10W
R944 1-216-811-11 METAL CHIP 150 5% 1/10W
R945 1-216-803-11 METAL CHIP 33 5% 1/10W
(S1000/S2000)
R945 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
R946 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
R947 1-216-803-11 METAL CHIP 33 5% 1/10W
(S2000C)
R948 1-216-811-11 METAL CHIP 150 5% 1/10W
R949 1-216-803-11 METAL CHIP 33 5% 1/10W
(S1000/S2000)
R949 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
R951 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
R952 1-216-803-11 METAL CHIP 33 5% 1/10W
(S2000C)
R953 1-216-811-11 METAL CHIP 150 5% 1/10W
R954 1-216-803-11 METAL CHIP 33 5% 1/10W
(S1000/S2000)
R954 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
R955 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
37
CDX-S1000/S2000/S2000C
KEY
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R956 1-216-803-11 METAL CHIP 33 5% 1/10W
R957 1-216-811-11 METAL CHIP 150 5% 1/10W
R957 1-216-817-11 METAL CHIP 470 5% 1/10W
R958 1-216-809-11 METAL CHIP 100 5% 1/10W
R958 1-216-813-11 METAL CHIP 220 5% 1/10W
R959 1-216-807-11 METAL CHIP 68 5% 1/10W
R959 1-216-813-11 METAL CHIP 220 5% 1/10W
R961 1-216-811-11 METAL CHIP 150 5% 1/10W
R962 1-216-805-11 METAL CHIP 47 5% 1/10W
R963 1-216-864-11 METAL CHIP 0 5% 1/10W
R964 1-216-809-11 METAL CHIP 100 5% 1/10W
R965 1-216-809-11 METAL CHIP 100 5% 1/10W
R966 1-216-807-11 METAL CHIP 68 5% 1/10W
R966 1-216-809-11 METAL CHIP 100 5% 1/10W
R967 1-216-811-11 METAL CHIP 150 5% 1/10W
MAIN
(S2000C)
(S2000C)
(S1000/S2000)
(S1000/S2000)
(S2000C)
(S1000/S2000)
(S2000C)
(S2000C)
(S2000C)
(S2000C)
(S2000C)
(S1000/S2000)
(S2000C)
R997 1-216-803-11 METAL CHIP 33 5% 1/10W
R998 1-216-864-11 METAL CHIP 0 5% 1/10W
< SWITCH >
S901 1-771-884-31 SWITCH, TACTILE (OFF)
S902 1-771-884-31 SWITCH, TACTILE (SOURCE)
S906 1-771-884-31 SWITCH, TACTILE (MODE)
S912 1-771-884-31 SWITCH, TACTILE (EQ3)
*************************************************************
A-3283-361-A MAIN BOARD, COMPLETE (S2000)
A-3283-365-A MAIN BOARD, COMPLETE (S1000)
A-3283-366-A MAIN BOARD, COMPLETE (S2000C)
*********************
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
< CAPACITOR >
C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(S2000/S2000C)
C2 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(S2000/S2000C)
C3 1-126-963-11 ELECT 4.7uF 20% 50V
(S2000/S2000C)
C4 1-126-947-11 ELECT 47uF 20% 16V
C5 1-126-947-11 ELECT 47uF 20% 16V
R968 1-216-807-11 METAL CHIP 68 5% 1/10W
(S2000C)
R969 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000C)
R970 1-216-864-11 METAL CHIP 0 5% 1/10W
(S1000/S2000)
R971 1-216-821-11 METAL CHIP 1K 5% 1/10W
R972 1-216-809-11 METAL CHIP 100 5% 1/10W
R976 1-216-819-11 METAL CHIP 680 5% 1/10W
(S2000C)
R977 1-216-833-11 METAL CHIP 10K 5% 1/10W
(S2000C)
R978 1-216-819-11 METAL CHIP 680 5% 1/10W
(S2000C)
R979 1-216-833-11 METAL CHIP 10K 5% 1/10W
(S2000C)
R980 1-216-815-11 METAL CHIP 330 5% 1/10W
(S2000C)
R981 1-216-817-11 METAL CHIP 470 5% 1/10W
R982 1-216-817-11 METAL CHIP 470 5% 1/10W
R983 1-216-817-11 METAL CHIP 470 5% 1/10W
R984 1-216-817-11 METAL CHIP 470 5% 1/10W
R985 1-216-817-11 METAL CHIP 470 5% 1/10W
R986 1-216-817-11 METAL CHIP 470 5% 1/10W
R987 1-216-811-11 METAL CHIP 150 5% 1/10W
R988 1-216-811-11 METAL CHIP 150 5% 1/10W
R989 1-216-811-11 METAL CHIP 150 5% 1/10W
R991 1-216-864-11 METAL CHIP 0 5% 1/10W
R992 1-216-840-11 METAL CHIP 39K 5% 1/10W
R993 1-216-857-11 METAL CHIP 1M 5% 1/10W
R994 1-216-821-11 METAL CHIP 1K 5% 1/10W
R995 1-216-821-11 METAL CHIP 1K 5% 1/10W
R996 1-216-821-11 METAL CHIP 1K 5% 1/10W
C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C10 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C11 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C12 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C51 1-126-947-11 ELECT 47uF 20% 16V
(S2000/S2000C)
C53 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C54 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C55 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C56 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C57 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C58 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(S2000/S2000C)
C59 1-164-237-11 CERAMIC CHIP 16PF 5% 50V
(S2000/S2000C)
C60 1-164-237-11 CERAMIC CHIP 16PF 5% 50V
(S2000/S2000C)
C62 1-162-959-11 CERAMIC CHIP 330PF 5% 50V
(S2000/S2000C)
C301 1-128-551-11 ELECT 22uF 20% 25V
C302 1-128-551-11 ELECT 22uF 20% 25V
C303 1-128-551-11 ELECT 22uF 20% 25V
C305 1-104-665-11 ELECT 100uF 20% 10V
C306 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C307 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C308 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C332 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
38
CDX-S1000/S2000/S2000C
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C333 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C343 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C401 1-126-964-11 ELECT 10uF 20% 50V
C404 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C405 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C406 1-126-960-11 ELECT 1uF 20% 50V
C407 1-126-960-11 ELECT 1uF 20% 50V
C412 1-126-947-11 ELECT 47uF 20% 16V
C413 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C431 1-126-964-11 ELECT 10uF 20% 50V
C432 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C441 1-126-964-11 ELECT 10uF 20% 50V
C442 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C451 1-126-964-11 ELECT 10uF 20% 50V
C452 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C461 1-126-964-11 ELECT 10uF 20% 50V
C462 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C479 1-126-947-11 ELECT 47uF 20% 16V
C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C503 1-104-665-11 ELECT 100uF 20% 10V
C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C508 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C509 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C511 1-126-964-11 ELECT 10uF 20% 50V
C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C515 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C516 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(S2000/S2000C)
C516 1-216-864-11 METAL CHIP 0 5% 1/10W
(S1000)
C517 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C518 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C601 1-131-868-81 ELECT 3300uF 20% 16V
C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C621 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C622 1-125-710-11 DOUBLE LAYERS 0.1F 5.5V
C623 1-104-665-11 ELECT 100uF 20% 10V
C631 1-126-961-11 ELECT 2.2uF 20% 50V
C750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C751 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C752 1-126-947-11 ELECT 47uF 20% 16V
C753 1-128-551-11 ELECT 22uF 20% 25V
C754 1-126-961-11 ELECT 2.2uF 20% 50V
C755 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C756 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C758 1-126-964-11 ELECT 10uF 20% 50V
C759 1-126-964-11 ELECT 10uF 20% 50V
C760 1-104-665-11 ELECT 100uF 20% 10V
C761 1-126-964-11 ELECT 10uF 20% 50V
C763 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C764 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C769 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C770 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C771 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
< CONNECTOR >
CN601 1-774-701-21 PIN, CONNECTOR 16P
CN701 1-794-311-21 PLUG, CONNECTOR 12P
CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P
< DIODE >
D1 8-719-069-55 DIODE UDZS-TE17-5.6B
D479 8-719-404-50 DIODE MA111-TX
D501 8-719-404-50 DIODE MA111-TX
D502 8-719-404-50 DIODE MA111-TX
D580 8-719-056-84 DIODE UDZ-TE-17-7.5B
D581 8-719-083-66 DIODE UDZS-TE17-18B
D601 8-719-049-38 DIODE 1N5404TU
D609 8-719-420-90 DIODE MA8051-M
D651 8-719-083-66 DIODE UDZS-TE17-18B
D710 8-719-977-12 DIODE DTZ6.8B
D711 8-719-977-12 DIODE DTZ6.8B
D712 8-719-977-12 DIODE DTZ6.8B
D715 8-719-422-76 DIODE MA8075-M
D716 8-719-977-12 DIODE DTZ6.8B
D717 8-719-977-12 DIODE DTZ6.8B
D718 8-719-977-12 DIODE DTZ6.8B
D719 8-719-083-66 DIODE UDZS-TE17-18B
D720 8-719-977-12 DIODE DTZ6.8B
D751 8-719-200-82 DIODE 11ES2
D752 8-719-200-82 DIODE 11ES2
D753 8-719-200-82 DIODE 11ES2
D754 8-719-200-82 DIODE 11ES2
D755 8-719-200-82 DIODE 11ES2
D756 8-719-200-82 DIODE 11ES2
D757 8-719-200-82 DIODE 11ES2
D758 8-719-200-82 DIODE 11ES2
D759 8-719-200-82 DIODE 11ES2
D760 8-719-200-82 DIODE 11ES2
D761 8-719-200-82 DIODE 11ES2
D762 8-719-200-82 DIODE 11ES2
< IC >
IC51 6-803-747-01 IC TDA7333-013TR (S2000/S2000C)
IC401 6-705-372-01 IC BD3808FS-FE2
IC501 6-803-736-01 IC MN101E01KDC
IC602 8-759-659-13 IC PST3428UL
IC750 6-705-360-01 IC TDA8588BJ/N2 (S2000/S2000C)
IC750 6-705-363-01 IC TDA8589BJ/N2 (S1000)
< JACK >
J1 1-815-185-13 JACK (ANTENNA)
J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)
J561 1-566-822-41 JACK (REMOTE IN) (S2000/S2000C)
< JUMPER RESISTOR >
JC1 1-216-864-11 METAL CHIP 0 5% 1/10W
JC331 1-216-296-11 SHORT CHIP 0
39
CDX-S1000/S2000/S2000C
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
JC401 1-216-864-11 METAL CHIP 0 5% 1/10W
JC451 1-216-296-11 SHORT CHIP 0
JC461 1-216-296-11 SHORT CHIP 0
JC501 1-216-864-11 METAL CHIP 0 5% 1/10W
JC503 1-216-864-11 METAL CHIP 0 5% 1/10W
JC681 1-216-864-11 METAL CHIP 0 5% 1/10W
JC753 1-216-296-11 SHORT CHIP 0
R29 1-216-809-11 METAL CHIP 100 5% 1/10W
(S2000/S2000C)
R51 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
R52 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
R53 1-216-801-11 METAL CHIP 22 5% 1/10W
(S2000/S2000C)
R54 1-216-833-11 METAL CHIP 10K 5% 1/10W
(S2000/S2000C)
< COIL >
L1 1-469-844-11 INDUCTOR 2.2uH
L301 1-469-876-11 INDUCTOR, FERRITE BEAD
L302 1-469-876-11 INDUCTOR, FERRITE BEAD
L303 1-469-876-11 INDUCTOR, FERRITE BEAD
L304 1-500-245-11 INDUCTOR, FERRITE BEAD
L305 1-500-245-11 INDUCTOR, FERRITE BEAD
L306 1-500-245-11 INDUCTOR, FERRITE BEAD
L307 1-469-876-11 INDUCTOR, FERRITE BEAD
L561 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
L562 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
L563 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
L601 1-456-617-11 COIL, CHOKE 250uH
< TRANSISTOR >
Q1 8-729-106-68 TRANSISTOR 2SD1615A-GP
Q22 1-801-806-11 TRANSISTOR DTC144EKA (S2000/S2000C)
Q51 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
(S2000/S2000C)
Q52 8-729-027-43 TRANSISTOR DTC114EKA-T146
(S2000/S2000C)
Q431 6-550-752-01 TRANSISTOR DTC614TKT146
Q441 6-550-752-01 TRANSISTOR DTC614TKT146
Q451 6-550-752-01 TRANSISTOR DTC614TKT146
Q461 6-550-752-01 TRANSISTOR DTC614TKT146
Q478 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q479 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q581 1-801-806-11 TRANSISTOR DTC144EKA
Q582 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q631 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q651 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146
R55 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000/S2000C)
R56 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
R57 1-414-595-11 INDUCTOR, FERRITE BEAD (S2000/S2000C)
R58 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000/S2000C)
R59 1-216-833-11 METAL CHIP 10K 5% 1/10W
(S2000/S2000C)
R60 1-216-833-11 METAL CHIP 10K 5% 1/10W
(S2000/S2000C)
R61 1-216-821-11 METAL CHIP 1K 5% 1/10W
(S2000/S2000C)
R301 1-216-864-11 METAL CHIP 0 5% 1/10W
R302 1-216-864-11 METAL CHIP 0 5% 1/10W
R405 1-218-881-11 METAL CHIP 27K 0.5% 1/10W
R406 1-216-809-11 METAL CHIP 100 5% 1/10W
R407 1-216-809-11 METAL CHIP 100 5% 1/10W
R408 1-216-809-11 METAL CHIP 100 5% 1/10W
R409 1-216-809-11 METAL CHIP 100 5% 1/10W
R431 1-216-809-11 METAL CHIP 100 5% 1/10W
R432 1-216-841-11 METAL CHIP 47K 5% 1/10W
R433 1-216-864-11 METAL CHIP 0 5% 1/10W
R441 1-216-809-11 METAL CHIP 100 5% 1/10W
R442 1-216-841-11 METAL CHIP 47K 5% 1/10W
R443 1-216-864-11 METAL CHIP 0 5% 1/10W
R451 1-216-809-11 METAL CHIP 100 5% 1/10W
R452 1-216-841-11 METAL CHIP 47K 5% 1/10W
R453 1-216-864-11 METAL CHIP 0 5% 1/10W
R461 1-216-809-11 METAL CHIP 100 5% 1/10W
R462 1-216-841-11 METAL CHIP 47K 5% 1/10W
R463 1-216-864-11 METAL CHIP 0 5% 1/10W
R479 1-216-805-11 METAL CHIP 47 5% 1/10W
R501 1-216-864-11 METAL CHIP 0 5% 1/10W
R502 1-216-809-11 METAL CHIP 100 5% 1/10W
R503 1-216-809-11 METAL CHIP 100 5% 1/10W
< RESISTOR >
R1 1-216-821-11 METAL CHIP 1K 5% 1/10W
R2 1-216-809-11 METAL CHIP 100 5% 1/10W
R3 1-216-809-11 METAL CHIP 100 5% 1/10W
R4 1-216-839-11 METAL CHIP 33K 5% 1/10W
R5 1-216-843-11 METAL CHIP 68K 5% 1/10W
R6 1-216-839-11 METAL CHIP 33K 5% 1/10W
(S2000/S2000C)
R7 1-216-843-11 METAL CHIP 68K 5% 1/10W
(S2000/S2000C)
R8 1-216-839-11 METAL CHIP 33K 5% 1/10W
(S2000/S2000C)
R9 1-216-843-11 METAL CHIP 68K 5% 1/10W
(S2000/S2000C)
R10 1-216-864-11 METAL CHIP 0 5% 1/10W
R11 1-216-864-11 METAL CHIP 0 5% 1/10W
40
R504 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R505 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R506 1-216-845-11 METAL CHIP 100K 5% 1/10W
R507 1-216-845-11 METAL CHIP 100K 5% 1/10W
R508 1-216-864-11 METAL CHIP 0 5% 1/10W
R509 1-216-813-11 METAL CHIP 220 5% 1/10W
R510 1-216-809-11 METAL CHIP 100 5% 1/10W
R511 1-216-809-11 METAL CHIP 100 5% 1/10W
R512 1-216-809-11 METAL CHIP 100 5% 1/10W
R513 1-216-845-11 METAL CHIP 100K 5% 1/10W
R514 1-216-845-11 METAL CHIP 100K 5% 1/10W
R515 1-247-807-31 CARBON 100 5% 1/4W
R516 1-247-807-31 CARBON 100 5% 1/4W
R517 1-216-841-11 METAL CHIP 47K 5% 1/10W
R518 1-216-821-11 METAL CHIP 1K 5% 1/10W
R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
CDX-S1000/S2000/S2000C
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R523 1-216-809-11 METAL CHIP 100 5% 1/10W
R524 1-216-809-11 METAL CHIP 100 5% 1/10W
R525 1-216-809-11 METAL CHIP 100 5% 1/10W
R526 1-216-809-11 METAL CHIP 100 5% 1/10W
R527 1-216-809-11 METAL CHIP 100 5% 1/10W
R528 1-216-845-11 METAL CHIP 100K 5% 1/10W
R530 1-216-845-11 METAL CHIP 100K 5% 1/10W
R531 1-216-845-11 METAL CHIP 100K 5% 1/10W
R532 1-216-845-11 METAL CHIP 100K 5% 1/10W
R534 1-216-833-11 METAL CHIP 10K 5% 1/10W
R535 1-216-845-11 METAL CHIP 100K 5% 1/10W
R536 1-216-845-11 METAL CHIP 100K 5% 1/10W
R539 1-216-864-11 METAL CHIP 0 5% 1/10W
(S2000/S2000C)
R540 1-216-845-11 METAL CHIP 100K 5% 1/10W
R541 1-216-845-11 METAL CHIP 100K 5% 1/10W
R543 1-216-845-11 METAL CHIP 100K 5% 1/10W
R544 1-216-821-11 METAL CHIP 1K 5% 1/10W
R547 1-216-864-11 METAL CHIP 0 5% 1/10W
R548 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2000C)
R549 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2000/S2000C)
R550 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S1000/S2000)
R551 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S1000)
R557 1-216-809-11 METAL CHIP 100 5% 1/10W
R558 1-216-864-11 METAL CHIP 0 5% 1/10W
(S1000)
R673 1-216-833-11 METAL CHIP 10K 5% 1/10W
R673 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R674 1-216-845-11 METAL CHIP 100K 5% 1/10W
R705 1-216-864-11 METAL CHIP 0 5% 1/10W
R706 1-216-864-11 METAL CHIP 0 5% 1/10W
R752 1-216-809-11 METAL CHIP 100 5% 1/10W
R756 1-216-841-11 METAL CHIP 47K 5% 1/10W
S702 1-692-431-21 SWITCH, TACTILE (RESET)
TU1 A-3220-959-A TUNER UNIT (TUX-032//Q)
X51 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz)
X501 1-813-160-11 VIBRATOR, CERAMIC (27MHz)
X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
*************************************************************
SENSOR
< SWITCH >
< TUNER >
< VIBRATOR >
SENSOR BOARD
**************
< SWITCH >
SERVO
(S1000)
(S2000/S2000C)
(S2000/S2000C)
R559 1-216-845-11 METAL CHIP 100K 5% 1/10W
R560 1-216-845-11 METAL CHIP 100K 5% 1/10W
R563 1-216-845-11 METAL CHIP 100K 5% 1/10W
R564 1-216-845-11 METAL CHIP 100K 5% 1/10W
R565 1-216-864-11 METAL CHIP 0 5% 1/10W
R566 1-216-864-11 METAL CHIP 0 5% 1/10W
R567 1-216-864-11 METAL CHIP 0 5% 1/10W
R568 1-216-864-11 METAL CHIP 0 5% 1/10W
(S1000)
R570 1-249-413-11 CARBON 470 5% 1/4W
R571 1-216-845-11 METAL CHIP 100K 5% 1/10W
R572 1-216-809-11 METAL CHIP 100 5% 1/10W
R582 1-216-821-11 METAL CHIP 1K 5% 1/10W
R583 1-216-821-11 METAL CHIP 1K 5% 1/10W
R584 1-216-849-11 METAL CHIP 220K 5% 1/10W
R585 1-216-849-11 METAL CHIP 220K 5% 1/10W
R609 1-216-821-11 METAL CHIP 1K 5% 1/10W
R631 1-249-425-11 CARBON 4.7K 5% 1/4W
R632 1-216-841-11 METAL CHIP 47K 5% 1/10W
R633 1-216-841-11 METAL CHIP 47K 5% 1/10W
R634 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R636 1-216-845-11 METAL CHIP 100K 5% 1/10W
R651 1-216-821-11 METAL CHIP 1K 5% 1/10W
R652 1-249-437-11 CARBON 47K 5% 1/4W
R653 1-216-833-11 METAL CHIP 10K 5% 1/10W
R654 1-216-833-11 METAL CHIP 10K 5% 1/10W
R671 1-216-809-11 METAL CHIP 100 5% 1/10W
R672 1-216-809-11 METAL CHIP 100 5% 1/10W
A-3283-339-A SERVO BOARD, COMPLETE
**********************
< CAPACITOR >
C1 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C2 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C3 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C5 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C6 1-100-381-11 ELECT CHIP 10uF 20% 16V
C7 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C8 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C13 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C17 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C18 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C19 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C21 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C23 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C25 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C26 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C27 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C28 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C29 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C30 1-162-921-11 CERAMIC CHIP 33PF 5% 50V
C31 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
C32 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C34 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
41
CDX-S1000/S2000/S2000C
SERVO
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C36 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C38 1-104-609-11 ELECT CHIP 100uF 20% 4V
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R77 1-216-833-11 METAL CHIP 10K 5% 1/10W
R78 1-216-833-11 METAL CHIP 10K 5% 1/10W
R79 1-216-833-11 METAL CHIP 10K 5% 1/10W
R80 1-216-833-11 METAL CHIP 10K 5% 1/10W
R81 1-216-833-11 METAL CHIP 10K 5% 1/10W
C70 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V
C71 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V
C72 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C73 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C74 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C75 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C76 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C77 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C78 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C79 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
< CONNECTOR >
CN1 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P
CN2 1-794-153-21 CONNECTOR, FPC (ZIF) 16P
< FERRITE BEAD >
FB1 1-414-760-21 FERRITE, EMI (SMD)
< IC >
IC1 6-703-699-01 IC uPD63712GC-8EU-A
IC2 6-705-002-01 IC BA5966FP-FE2
< FERRITE BEAD >
JR40 1-414-760-21 FERRITE, EMI (SMD)
JR41 1-414-760-21 FERRITE, EMI (SMD)
JR90 1-414-760-21 FERRITE, EMI (SMD)
JR91 1-414-760-21 FERRITE, EMI (SMD)
< TRANSISTOR >
Q1 8-729-904-87 TRANSISTOR 2SB1197K-R
< RESISTOR >
R1 1-216-841-11 METAL CHIP 47K 5% 1/10W
R6 1-216-833-11 METAL CHIP 10K 5% 1/10W
R7 1-216-840-11 METAL CHIP 39K 5% 1/10W
R9 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R11 1-216-833-11 METAL CHIP 10K 5% 1/10W
R82 1-216-837-11 METAL CHIP 22K 5% 1/10W
R83 1-216-833-11 METAL CHIP 10K 5% 1/10W
R84 1-216-837-11 METAL CHIP 22K 5% 1/10W
R85 1-216-833-11 METAL CHIP 10K 5% 1/10W
< SWITCH >
SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< VIBRATOR >
X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz)
*************************************************************
MISCELLANEOUS
***************
7 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
0 153 8-820-207-02 OPTICAL PICK-UP KSS1000E/K1RP
154 A-3372-448-A CHASSIS (OP) SUB ASSY (including M901)
F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
M902 A-3372-447-A MOTOR ASSY, SL (SLED)
M903 A-3372-443-A MOTOR ASSY, LE (LOADING)
SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
*************************************************************
ACCESSORIES
************
3-259-960-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN,
FRENCH,ITALIAN,DUTCH)
(S2000/S2000C)
3-259-961-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN,FRENCH,ITALIAN,DUTCH)
(S2000/S2000C)
3-261-422-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN,
FRENCH,ITALIAN,DUTCH)
(S1000)
3-261-423-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN,FRENCH,ITALIAN,DUTCH)
(S1000)
X-3383-264-2 CASE ASSY (for FRONT PANEL)
*************************************************************
R12 1-216-809-11 METAL CHIP 100 5% 1/10W
R13 1-216-833-11 METAL CHIP 10K 5% 1/10W
R14 1-216-797-11 METAL CHIP 10 5% 1/10W
R15 1-216-797-11 METAL CHIP 10 5% 1/10W
R41 1-216-821-11 METAL CHIP 1K 5% 1/10W
R42 1-216-821-11 METAL CHIP 1K 5% 1/10W
R44 1-414-760-21 FERRITE, EMI (SMD)
R45 1-414-760-21 FERRITE, EMI (SMD)
R70 1-216-842-11 METAL CHIP 56K 5% 1/10W
R71 1-216-833-11 METAL CHIP 10K 5% 1/10W
R72 1-216-842-11 METAL CHIP 56K 5% 1/10W
R73 1-216-833-11 METAL CHIP 10K 5% 1/10W
R74 1-216-837-11 METAL CHIP 22K 5% 1/10W
R75 1-216-833-11 METAL CHIP 10K 5% 1/10W
R76 1-216-837-11 METAL CHIP 22K 5% 1/10W
42
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
301 X-3382-647-1 FRAME ASSY, FITTING
302 X-3382-926-1 SCREW ASSY (BS), FITTING
303 3-349-410-11 BUSHING
304 3-246-468-01 COLLAR
305 1-465-459-21 ADAPTOR, ANTENNA
306 3-246-471-01 KEY (FRAME)
307 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
302301
303
305304 306
CDX-S1000/S2000/S2000C
307
43
CDX-S1000/S2000/S2000C
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2003. 11 New
44
Loading...