Sony CDXR-3000, CDXRW-300 Service manual

Download

Page 1

CDX-R3000/RW300

SERVICE MANUAL

Ver. 1.2 2006.05

• The tuner and CD sections have no adjustments.

AUDIO POWER SPECIFICATIONS (US Model)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION

23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.

SPECIFICATIONS

CD player section

Signal-to-noise ratio 120 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit

Tuner section

Tuning range US, Canadian Model:

87.5 – 107.9 MHz E model: FM tuning interval: 50 kHz/200 kHz switchable

87.5 – 108 MHz (at 50 kHz step)

87.5 – 107.9 MHz (at 200 kHz step) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo),

69 dB (mono)

Harmonic distortion at 1 kHz

0.5% (stereo),

0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz

US Model

CDX-R3000/RW300

Canadian Model

E Model

CDX-R3000

Model Name Using Similar Mechanism NEW CD Drive Mechanism Type MG-611XA-186//K Optical Pick-up Name KSS1000E

Tuning range US, Canadian Model:

530 – 1,710 kHz E Model: AM tuning interval: 9 kHz/10 kHz switchable 531 – 1,602 kHz (at 9 kHz step)

530 – 1,710 kHz (at 10 kHz step) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV

Power amplifier section

Outputs Speaker outputs

(sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms)

General

Outputs Audio outputs terminal (rear/sub switchable)

Power antenna relay control terminal

Power amplifier control terminal Inputs Antenna input terminal

Remote controller input terminal (E Model) Tone controls Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD)

9-961-386-03

– Continued on next page –

FM/AM COMPACT DISC PLAYER

Sony Corporation

eVehicle Division Published by Sony Techno Create Corporation

Page 2

CDX-R3000/RW300

Power requirements 12 V DC car battery

(negative ground)

Dimensions Approx. 178 × 50 × 179 mm

(7 1/8 × 2 × 7 1/8 in.) (w/h/d)

Mounting dimensions Approx. 182 × 53 × 161 mm

(7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d)

Mass Approx. 1.2 kg

(2 lb. 10 oz.)

Supplied accessories Parts for installation and connections (1 set)

Front panel case (1)

Design and specifications are subject to change without notice.

SERVICE NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block.

optical pick-up

semi-fixed resistor

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

Notes on Chip Component Replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

TEST DISCS

This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability:

CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2)

• E model

This label is located on the bottom of the chassis.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

Page 3

CDX-R3000/RW300

Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)

This unit can play the following discs:

Type of discs Label on the disc

Audio CD

MP3 files

• Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit.

• You cannot play a CD-R/CD-RW that is not finalized∗.

• You can play MP3 files recorded on CD-ROMs, CD-Rs, and

CD-RWs.

• A CD-R/CD-RW to which a session can be added can be played.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

∗ A process necessary for a recorded CD-R/CD-RW disc to be

played on the audio CD player.

EXTENSION CABLE AND SERVICE POSITION

When repairing or servicing this set, connect the jig (extension cable) as shown below.

• Connect the MAIN board (CN751) and the SERVO board (CN1) with the extension cable (Part No. J-2502-076-1).

MAIN BOARD CN751

J-2502-076-1

SERVO BOAR CN1

Page 4

CDX-R3000/RW300

1. GENERAL

Location of Controls (US, Canadian Model) .......................... 5

Location of Controls (E Model) .............................................. 5

Connections (US, Canadian Model)........................................ 6

Connections (E Model) ........................................................... 7

2. DISASSEMBLY

2-1. Sub Panel (1) Assy .............................................................. 9

2-2. CD Mechanism Block ......................................................... 9

2-3. Main Board ....................................................................... 10

2-4. Chassis (T) Sub Assy ........................................................ 10

2-5. Roller Arm Assy................................................................11

2-6. Chassis (OP) Assy.............................................................11

2-7. Optical Pick-up ................................................................. 12

2-8. SL Motor Assy (M902) .....................................................12

2-9. LE Motor Assy (M903)..................................................... 13

2-10. Servo Board....................................................................... 13

3. DIAGRAMS

3-1. IC Pin Descriptions ........................................................... 14

3-2. Block Diagram –CD Section–........................................... 18

3-3. Block Diagram –Main Section–........................................19

3-4. Block Diagram –Display Section–....................................20

3-5. Circuit Boards Location .................................................... 20

3-6. Note for Printed Wiring Boards and

Schematic Diagrams ..........................................................21

3-7. Waveforms......................................................................... 21

3-8. Printed Wiring Boards –CD Mechanism Section–............ 22

3-9. Schematic Diagram –CD Mechanism Section– ................23

3-10. Schematic Diagram –Main Section (1/2)– ........................24

3-11. Schematic Diagram –Main Section (2/2)– ........................25

3-12. Printed Wiring Boards –Main Section– ............................ 26

3-13. Printed Wiring Board –Display Section– .......................... 27

3-14. Schematic Diagram –Display Section–............................. 28

3-15. IC Block Diagrams............................................................ 29

4. EXPLODED VIEWS

4-1. Main Section ..................................................................... 31

4-2. Front Panel Section ........................................................... 32

4-3. CD Mechanism Section (1) ...............................................33

4-4. CD Mechanism Section (2) ...............................................34

4-5. CD Mechanism Section (3) ...............................................35

4-6. CD Mechanism Section (4) ...............................................36

5. ELECTRICAL PARTS LIST ........................................ 37

Page 5

CDX-R3000/RW300

SECTION 1

GENERAL

(US, Canadian Model) (E Model)

This section is extracted from instruction manual.

Page 6

CDX-R3000/RW300

Connections (US, Canadian Model)

Page 7

Connections (E Model)

CDX-R3000/RW300

Page 8

CDX-R3000/RW300

SECTION 2

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

SET

2-1. SUB PANEL (1) ASSY

(Page 9)

2-2. CD MECHANISM BLOCK

(Page 9)

2-3. MAIN BOARD

(Page 10)

2-7. OPTICAL PICK-UP

(Page 12)

2-4. CHASSIS (T) SUB ASSY

(Page 10)

2-5. ROLLER ARM ASSY

(Page 11)

2-6. CHASSIS (OP) ASSY

(Page 11)

2-8. SL MOTOR ASSY (M902)

(Page 12)

2-10. SERVO BOARD

(Page 13)

2-9. LE MOTOR ASSY (M903)

(Page 13)

Page 9

Note : Follow the disassembly procedure in the numerical order given.

)

2-1. SUB PANEL (1) ASSY

two claws

CDX-R3000/RW300

two

screws

(+PTT 2.6

2-2. CD MECHANISM BLOCK

CD mechanism block

sub panel (1) assy

bracket (CD)

two

screws

(+PTT 2.6

two claw

screw

(+PTT 2.6

CN751

screw

(+PTT 2.6

Page 10

CDX-R3000/RW300

)

2-3. MAIN BOARD

three screws

(+BTT)

MAIN board

two

screws

(+PTT 2.6

2-4. CHASSIS (T) SUB ASSY

two

screws

(+P 1.7

SENSOR board

claw

2.2)

claw

two

screws

(+P 1.7

2.2)

chassis (T) sub assy

Page 11

2-5. ROLLER ARM ASSY

)

worm wheel (RA)

spring (RAL)

washer (1.0 – 2.5)

roller arm assy

spring (RAR)

CDX-R3000/RW300

2-6. CHASSIS (OP) ASSY

compression spring (damper)

washer

gear (LE1)

lever (D)

chassis (OP) assy

CN2

two compression springs (damper

slider (R)

Remove the six solderings.

tennsion coil spring (KF)

Page 12

CDX-R3000/RW300

2-7. OPTICAL PICK-UP

claw

chucking arm sub assy

tension coil spring (CHKG)

optical pick-up

2-8. SL MOTOR ASSY (M902)

main shaft

rack (SL)

screw

(+B 1.4

SL motor assy (M902)

screw

(+P 1.4

1.8)

Page 13

2-9. LE MOTOR ASSY (M903)

two toothed lock

(+M 1.4

bracket (LEM)

screw

(+M 1.7

)

screws

2.5)

screw

(+P 1.7

2.2)

screw

(+M 1.7

(M903)

woam (LEB) assy

2.5)

LE motor assy

leaf spring (LE)

screw

(+M 1.7

bearing (LEB)

washer

gear (LE1)

lever (D)

CDX-R3000/RW300

2.5)

slider (R)

2-10. SERVO BOARD

Remove the eight solderings.

Remove the soldering.

SERVO board

Remove the three solderings.

toothed lock

(M 1.7)

screw

claw

CN2

Page 14

CDX-R3000/RW300

SECTION 3

DIAGRAMS

3-1. IC PIN DESCRIPTIONS

• IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)

Pin No. Pin Name I/O Pin Description

1LDOLaser diode ON/OFF control signal output (L: laser OFF, H: laser ON) 2PDIDimmer monitor input from optical pick-up laser diode. 3PNINot used. (Fixed at L in this set) 4AVDD — Analog power supply pin (+3.3 V) 5 DGND — Ground 6 RFOK O RFOK signal output to system control IC. 7 INTQ O CD text pack synchronization signal output to system control IC. 8 RST I CD reset signal input from system control IC.

9A0I

10 STB I Data strobe signal input from system control IC. 11 SCK I Serial clock input from system control IC. 12 SO O Serial data output to system control IC. 13 SI I Serial data input from system control IC. 14 DVDD — Power supply pin (+3.3 V) 15 DAVDD — D/A converter power supply (+) pin (+3.3 V) 16 ROUT O Analog audio signal output (R-ch) 17 DAGND — Ground 18 REGC — Capacitor connection pin for SCF regulator. 19 DAGND — Ground 20 LOUT O Analog audio signal output (L-ch) 21 DAVDD — D/A converter power supply (+) pin (+3.3 V) 22 XVDD — Power supply pin (+3.3 V) 23 XTAL O Main system clock output (16.9344 MHz) 24 XTAL I Main system clock input (16.9344 MHz) 25 XGND — Ground 26 DVDD — Power supply pin (+3.3 V) 27 C1D1/FZD O Not used. (Open) 28 C1D2/TZD O Not used. (Open) 29 C2D1/RMUTE O CD R-ch data zero detection signal output 30 C2D2/LMUTE O CD L-ch data zero detection signal output 31 C2D3/SHOCK/SBSY O Not used. (Open) 32 LOCK/FR O Not used. (Open) 33 WFCK/MIRR O Not used. (Open) 34 RFCK/HOLD O Not used. (Open) 35 PLCK O Not used. (Open) 36 C16M O Not used. (Open) 37 DGND — Ground 38 TX O Not used. (Open) 39 EMPH/RAMOVER O Not used. (Open) 40 FLAG O Not used. (Open) 41 DVDD — Power supply pin (+3.3 V) 42 LIMIT I Not used. (Fixed at L in this set)

43 XTALEN I 44 DGND — Ground

45 DIN I Not used. (Connect to DOUT in this set) 46 DOUT O Not used. (Connect to DIN in this set) 47 SCKIN I Not used. (Connect to SCKO in this set) 48 SCKO O Not used. (Connect to SCKIN in this set) 49 LRCKIN I Not used. (Connect to LRCK in this set)

Command/parameter discrimination signal input from system control IC. (L: command transmission, H: parameter transmission)

Oscillation circuit ON/OFF control signal input (L: ON, H: OFF) (Fixed at L in this set)

Page 15

Pin No. Pin Name I/O Pin Description

50 LRCK O Not used. (Connect to LRCKIN in this set) 51 DVDD — Power supply pin (+3.3 V) 52 FD+ O Focus servo drive PWM signal output (+) 53 FD– O Focus servo drive PWM signal output (–) 54 TD+ O Tracking servo drive PWM signal output (+) 55 TD– O Tracking servo drive PWM signal output (–) 56 SD+ O Sled servo drive PWM signal output (+) 57 SD– O Sled servo drive PWM signal output (–) 58 MD+ O Spindle servo drive PWM signal output (+) 59 MD– O Spindle servo drive PWM signal output (–) 60 DGND — Ground 61 TESTEN I Test setting input (Fixed at L in this set)

62 to 66 TEST4 to TEST0 I Test setting input (Fixed at L in this set)

67 ADGND — A/D converter power supply (–) pin 68 EFM O EFM signal output 69 ASY I EFM comparator reference voltage input 70 ADVDD — A/D converter power supply pin (+3.3 V) 71 RFI I RF signal input for EFM data growing. 72 EQ2 — Not used. (Open) 73 EQ1 — RF amplifier equalizer parts connection pin 74 RF– I Not used. (Open) 75 RF2– I RF amplifier inversion input 76 AGCO O RF signal output after on AGC. 77 AGCI I RF AGC signal amplifier input 78 RFO O RF signal output before on AGC. 79 ATEST I Not used. (Open) 80 C3T — Capacitor connection pin for 3T detection. 81 AGND — Ground 82 A I Signal input (A) from optical pick-up detector. 83 C I Signal input (C) from optical pick-up detector. 84 B I Signal input (B) from optical pick-up detector. 85 D I Signal input (D) from optical pick-up detector. 86 F I Signal input (F) from optical pick-up detector. 87 E I Signal input (E) from optical pick-up detector. 88 VREFIN I Reference voltage (+1.65 V) input 89 AVDD — Analog po wer supply pin (+3.3 V) 90 REFOUT O Reference voltage (+1.65 V) output 91 REFC — Capacitor connection pin for reference voltage output. 92 FE– I Focus error signal amplifier inversion input 93 FEO O Focus error signal amplifier output 94 ADCIN I Not used. (Open) 95 TE- I Tracking error signal amplifier inversion input 96 TEO O Tracking error signal amplifier before output 97 TE2 O Tracking error signal amplifier after output 98 TEC I Tracking error signal comparator input 99 AGND — Ground

100 PWMSW I Not used. (Fixed at L in this set)

CDX-R3000/RW300

Page 16

CDX-R3000/RW300

• IC801 MB90473PF-G166-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (2/2))

Pin No. Pin Name I/O Pin Description

1ATT O Audio mute control signal output

2 to 4 NC — Not used in this set. (Open)

5 BEEP O Beep signal output to power amp IC 6VOL ATT O Electrical volume ATT control output

7 to 10 NC — Not used in this set. (Open)

11 VSS — Ground pin

12 to 14 NC — Not used in this set. (Open)

15 TU ATT O Tuner mute control output

16, 17 NC — Not used in this set. (Open)

18 CD SI I CD servo serial data signal input 19 CD SO O CD servo serial data signal output 20 CD SCK O CD servo serial clock signal output 21 RE 0 O Not used in this set. (Open) 22 RE 1 O Not used in this set. (Open) 23 VCC+3.3 — Power supply pin (+3.3 V) 24 EEP SIO I/O Serial data signal input/output for EEPROM comunication 25 EEP SCK O Serial clock signal output for EEPROM comunication

26 SHUT SW I

27 LCD CE O Chip enable signal output to LCD driver IC 28 LCD SO O Serial data signal output to LCD driver IC Flash: UART serial out 29 LCD SCK O Serial clock signal output to LCD driver IC 30 NC — Not used in this set. (Open) 31 STB O Standby signal output to power amp IC 32 AUX — Not used in this set. (Open) 33 IIC SCK O IIC bus serial clock signal output 34 IIC SIO I/O IIC bus serial data signal input/output 35 VCC+3.3 — Power supply pin (+3.3 V) (for A/D converter) 36 AVRH+3.3 — External reference power supply (+3.3 V) (for A/D converter) 37 AVSS — Ground pin (for A/D converter)

38, 39 KEY IN0, 1 I Key signal input

40 NC — Not used in this set. (Open) 41 RC IN0 I Rotary commander key signal input 42 VSS — Ground pin

43, 44 NC — Not used in this set. (Fixed at “L”.)

45 VSM I S meter voltage detect signal input 46 DST SEL I Destination select pin 47 KEY ACK I Key acknowledge detect signal input 48 NC — Not used in this set. (Open)

49, 50 MD0, 1 I Input for operation mode designation (Fixed at “H”.)

51 MD2 I Input for operation mode designation (Fixed at “L”.) 52 NC — Not used in this set. (Open) 53 BU IN I Back up power supply detect signal input 54 OP REQ/INTQ O OP REQ/INTQ select signal output 55 CD SELFSW I CD mechanism self load position detect switch signal input 56 DIAG I Condition input from power amp IC 57 TU ATT IN I Tuner ATT signal input Not used in this set. (Open) 58 UNI SI I Serial data signal input Not used in this set. (Open) 59 UNI SO O Serial data signal output Not used in this set. (Open) 60 UNI SCK O Serial clock signal output Not used in this set. (Open) 61 BUS ON O Bus on signal output 62 SYS RST O System reset signal output

Shutter switch open/close detect signal input “L”: Panel open, “H”: Panel close

Page 17

Pin No. Pin Name I/O Pin Description

63 TEL ATT O TEL ATT signal output Not used in this set. (Open) 64 ACC IN I Accessory power supply detect signal input 65 SIRCS I Remote control signal (infrared rays) input 66 RAM BU O Not used in this set. (Fixed at “L”.) 67 TEST IN I Test mode detect signal input

68 FLASH W I

69 NOSE SW O Not used in this set. (Fixed at “H”.)

70, 71 NC — Not used in this set. (Open)

72 DOOR SW I

73 DOOR IND O Not used in this set. (Open) 74 RC IN1 I Rotary commander shift key signal input 75 XKEY ON O Key power supply control signal output Pin rj (KEY ACK) active: “L” output 76 NC — Not used in this set. (Open) 77 RESET I Reset signal input 78 NC — Not used in this set. (Open) 79 X1A — Oscillator connect pin (32 kHz) 80 X0A — Oscillator connect pin (32 kHz) 81 VSS — Ground pin 82 X0 — Oscillator connect pin (3.68 MHz) 83 X1 — Oscillator connect pin (3.68 MHz) 84 VCC+3.3 — Power supply pin (+3.3 V)

85 to 88 NC — Not used in this set. (Open)

89 ZERO DET R I Mechanism deck mute zero closs detect signal input R 90 ZERO DET L I Mechanism deck mute zero closs detect signal input L 91 CD STB O CD servo data strob signal output Timing of data latch: “L” output 92 CD IN SW I CD mechanism IN-SW detect signal input 93 CD LOAD O CD mechanism loading motor control signal output 94 CD ON/EJECT O CD mechanism eject motor control signal output 95 CDM ON/D SW I CD mechanism DSW detect signal input 96 CD LIMIT I CD mechanism IN-LIMIT SW signal input 97 RFOK I CD servo RFOK signal input 98 CD XRST O CD servo reset signal output

99 CD A0 O

100 NC — Not used in this set. (Open)

Memory mode changeover signal input Normally “H” input (single chip mode) “L” after reset: Flash write mode

Front panel open/close detect signal input “L” input: Panel close, “H” input: Panel open

CD servo command/parameter identification signal output Command transmission: “L” output, parameter transmission: “H” output

CDX-R3000/RW300

17 17

Page 18

CDX-R3000/RW300

3-2. BLOCK DIAGRAM — CD SECTION —

DETECTOR

PD1

PD2

PD1

PD2

I-V AMP

RFO

• R-ch is omitted due to same as L-ch.

• Siganal Path

: CD PLAY

AGCO

AGCI

RF AMP,DIGITAL SERVO,

DIGITAL SIGNAL PROCESSOR

IC1

EFM

RFI

ASY

LOUT

ROUT

LMUTE

RMUTE

R-CH

ZERO DET L

ZERO DET R

CD-L

MAIN

SECTION

(Page 19)

LASER DIODE

PICK-UP BLOCK

(KSS-1000E)

2-AXIS DEVICE

(FOCUS)

(TRACKING)

PD LD

OPTICAL

FCS+

FCS–

TRK+

TRK–

AUTOMATIC

POWER

CONTROL

M902

(SLED)

FOCUS/TRACKING COIL DRIVE,

FEO

TEO

SLED/SPINDLE/LOADING

MOTOR DRIVE

IC2

VO2–

VO2+

VO1–

VO1+

VO4+

VO4–

OPIN2+

OPIN2–

OPIN1+

OPIN1–

OPIN4+

OPIN4–

FE–

TE2

TE–

TEC

SCK

RFOK

INTQ

STB

RST

FD+

FD–

TD+

TD–

SD+

SD–

XTAL

16.934MHz

SW1

(DOWN)

SW2

(SELF)

SW3

(DISC IN)

CD_SI

CD_SO

CD_SCK

RF_OK

OP INTQ

CD_STB

CD_A0

CD XRST

CD_DSW

CD_SELFSW

CD_INSW

SYSTEM CONTROL

IC801 (1/3)

M901

(SPINDLE)

M903

(LOADING)

OPIN3+

OPIN3–

FWD

REV

VO3+

VO3–

VOL+

VOL–

MD+

MD–

SW4

(LIMIT)

CD_LIMIT

CD LOAD

CD ON/EJECT

1818

Page 19

3-3. BLOCK DIAGRAM — MAIN SECTION —

ELECTRONIC VOLUME

IC401

CDX-R3000/RW300

PJ601

(ANTENNA)

SECTION

(Page 18)

TUX601

(TUNER UNIT)

ANT

VCC

TU VDD

E2P VDD

TU-SCL TU-SDA

S-METER TU MUTE

E2P SCL

E2P SDA

CD-L

L R

4 3

10 11 15

13 14

6 7

16 17

R-CH

AU+8V TU+5V

U COM+3.3V

SCL SDA

SYSTEM CONTROL

IC801 (2/3)

VSM

TU ATT

EEP SCK

EEP SIO

OUTS1 OUTS2

OUTF2

OUTR2

OUTF1

OUTR1

MUTE

SCL SDA

IIC SCK

IIC SIO

VOL ATT

ATT

BEEP

STB

DIAG

17 18

25 24

30 31

33 34

5 31 56

R-CH

R-CH (FRONT) R-CH (REAR)

SCL SDA

SCL

SDA

MUTE

Q407

MUTE CONTROL

Q400,401

R-CH

MUTE

Q405

D400

MUTE

Q404

BATT

SDA SCL

PJ401

REAR

AUDIO OUT

INRR(FL)

INRF(RL)

SDA

SCL

ACGND

STB

DIAG

POWER AMP

IC100

PR+

PR-

RF+

RF-

SW1 SW2

REG1 REG2 REG3 REG4 REG5

29 27

30 37 31 33 34

5 3

9 7

R-CH

BATT

AU+8V U-COM+3.3V SERVO+3.3V

MECHA+6V DISP+B

F900

CNP901

FL+

FL-

RL+ RL-

FR+ FR-

RR+ RR-

AMP-REM

ANT-REM

ACC IN

TEST IN

BU IN

: CD PLAY

: FM

: AM

D912

BATT

TU+5V

TU+5V REG

Q601

BATTERY CHECK

Q902,906,907

• R-CH is omitted due to same as L-CH.

• Signal Path

ACC CHECK

Q900

AU+8V

ACC

TEST

19 19

Page 20

CDX-R3000/RW300

)

3-4. BLOCK DIAGRAM — DISPLAY SECTION — 3-5. CIRCUIT BOARDS LOCATION

KEY MATRIX

S501-522

E model

CNP900

(REMOTE IN)

E model

S800

FREQUENCY

()

SELECT

U COM+3.3V

SYSTEM CONTROL

IC801 (3/3)

LCD DRIVER

IC501

SERVO board

SENSOR board

KEYIN0

+3.3V REG

IC906

V OUT

LCD501

LIQUID CRYSTAL DISPLAY

PANEL

DIMMER CONTROL Q501,502

DISP+B

VDD

LED501,502

LCD

BACK LIGHT

()

LED504,-518,

520-522, 524,525

DISP+B

DISPLAY board

LCD SO

SEG3

SEG50

COM4

COM1

DIMMER

LED503

(DISC IND)

D521

KEYIN1

D801

KEY

ACKNOWLEDGE

SWITCH

Q800

D810

10K

US,Canadian model

X801

32.768kHz

S802

RESET

IC802

OUT

74 41

KEY ACK

XKEY ON

RCIN1 RCIN0

DST SEL

RESET

X1A

X0A

LCD SCK

LCD CE

SHUT SW

SIRCS

29 27

CLK

DISP+B

D820

S823

(SHUTTER)

REMOTE CONTROL SIGNAL RECEIVER

IC502

VCC

OUT

X800

3.68MHz

SPEAKER board

tuner unit (TUX601

MAIN board

2020

Page 21

3-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 3-7. WAVEFORMS

CDX-R3000/RW300

Ver. 1.2

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)

For schematic diagrams.

Note:

• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/ specified.

•

• C : panel designation.

• A : B+ Line.

• B : B– Line.

• H : adjustment for repair.

•Voltages and waveforms are dc with respect to ground

• CD mechanism section

no mark : CD PLAY

• Main (1/2), (2/2) and Display sections

no mark : FM

: internal component.

Note:

The components identified by mark 0 or dotted line with mark 0 are criti- cal for safety. Replace only with part number specified.

under no-signal (detuned) conditions.

(): AM <>: CD PLAY

W or less unless otherwise

Note:

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

∗ : Impossible to measure

•Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.

•Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances.

• Circled numbers refer to waveforms.

• Signal path.

J : CD PLAY F : FM f : AM

• Abbreviation CND : Canadian model.

For printed wiring boards.

Note:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

•

• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated.

• Abbreviation

: Through hole.

These are omitted

CND : Canadian model.

— Servo Board —

(MODE: CD PLAY)

16.9344MHz

IC1 wd (XTAL)

(AGCI)

IC1

Approx. 620mVp-p

(FEO)

IC1

Approx. 200mVp-p

(TEO)

IC1

1.2Vp-p

0.85V to

1.45Vp-p

— Main Board —

32.768kHz

IC801 i; (X0A)

3.68MHz

IC801

1.7Vp-p

2.4Vp-p

(X0)

21 21

Page 22

CDX-R3000/RW300

3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 20 for Circuit Boards Location. : Uses unleaded solder.

234567891011 12 13 14

R42

FB1

R41

IC1

C19

R45

C18

R44

C21

C23

C32

C27

C25

C36

C26

C31

C30

R13

C28

C39

C29

C38

R15

R11

R14

C34

R12

C37

C35

CN2

CN1

(Page 26)

C20

JR91

JR90

JR40

C11

C13

JR41

C17

R74

R76

R72

R77

R70

R75

R71

R73

C73

C72

C75

C71

C70

IC2

C78

C77

C76

C79

R83

C74

R85

R84

R81

R79

R82

R80

R78

SW1

SW3

SW2

1-688-822-

2222

Page 23

• Refer to page 21 for Waveforms.

3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 29 for IC Block Diagram.

CDX-R3000/RW300

C20

SW3

SW2

CN2

TP27

TP28

TP29

TP31

TP30 TP29 TP14

TP28

TP27

TP26

TP19 C18

R13

C36

C37

R12

C35

C34

R11

SW4

M901

M902

TP81 TP80

SW1

TP85 TP83 TP84

TP82

TP87

TP88

TP89

TP90

TP91

R14 R15

C38

TP33TP32

TP20

C39

C28

TP22

C29

C26

TP21

C27

TP23

C30

TP24

TP25

C31

C32

C23

C25

C21

C19

IC1

C17

C13

TP13 TP12

TP11

TP10 TP9

TP8 TP7

TP6 TP5

TP4 TP3

TP2

TP1

C11

JR91

JR90

FB1

R41 JR41 JR40

R42

TP65 TP64

TP63 TP62

TP61 TP60

R45

TP59

R44

TP58 TP57

TP56 TP55

TP54 TP48

TP52 TP51 TP53

TP49 TP50

TP47 TP46

TP45 TP44

TP43 TP42 TP41

TP40

CN1

(Page 25)

M903

TP92 TP93

R70 R71

R72

R74 R75

R76

C70

C71

R73

C72

C73

R77

TP100

TP71 TP70

TP73 TP72

IC B/D

C74

IC2

C79

R85

R84

R82R83

C78

C77

R80R81

C76

R78R79

TP75

TP74

C75

23 23

Page 24

CDX-R3000/RW300

3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 30 for IC Block Diagram.

TUX601

PJ601

R401

R400

C400

C600

JR103

C414

C409

C408 C411

C410

Q601

IC B/D

IC401

L602

R606

R412 R411

R409

R407

R406 R405

R404

R435

R436

L400

C416

R604

JR10

R603

C417

R607

R608

C451 C450

C453

C428

C452

R441

R443

C424

C426

C425

R417

C435

C436

C303

D907

D908

D909

D917

C108

D916

CNP901

IC100

R416

R421

R420

R415

R414

R419

R418

JR6

R440

R442

Q407

Q405

Q404

Q403

Q402

Q406

C440

C444

C438

C437

R431

R432

R429

R427

C113

C106

C101

C107

D921

D922

D904

D903

D902

D905

D906

PJ401

C619C618

D600

R615

C620

Q400

Q401

C430

D400

R424

R902

Q900

R903

C908

R904

C111

C109

C922

R931

R932 R913

D914

F900

L900

D919

(Page 25)

2424

Page 25

3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 21 for Waveforms.

R813

CDX-R3000/RW300

(Page 24)

(Page 23)

CN751

C705

C701

C709

C707

R708

R709

R707

R703

JR11

L702

L701

L700

C704 R722

R843

R802

R851

CNP800

D820

S800

R865

R864

R815

R800

R808

C823

C824

R806

C807

R821

R823

R822

R832R834

R805

R809

R819

R818

C813

C821

R801

R804

R850 IC801

R826

R835

R849

JW138

D810

D801

R828

R830

R862

R861

R839

R840

R841

R852

R848

R844

R447

C446

C447

C441

R448

C816 C817

C812

R873

D702

R854

X801

C801

R925

R845

R860

C802

R901

R936

R853

R705

C822

X800

IC802

C820

R837

C810

C818

C825

C809

R838

R846

R847

R810

R811

JR5

(Page 28)

CNP900

R915

R914

D817

D815

D816

D814

D813

D812

D811

R833

R814

Q800

R927

25 25

C706

Q906

R825

C815

R824

Q907

D808

R437

C909

S802

D915

R917 R928

Q902

R912

D912

Page 26

CDX-R3000/RW300

3-12. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 20 for Circuit Boards Location. : Uses unleaded solder.

PJ601

C600

R606

R608

R607

TUX601

JW47

JW48

JW3

JW4

23456789101112131415

PJ401

CNP900

R838

R846

JW19

S802

R853

X800

JW91

C701

D903

JW100

C709

C818

C812

JW18

CNP901

D916

CN751

R708

C822

C817

C816

JW17

D917

R932

JW103

R936

C820

JW16

C815

JW102

FMB3

R873

R814

R931

JW15

C922

JW101

R860

JW14

R437

R847

C825

JW13

D808

JW99

JW78

R901

D914

L701

R811

JR5

R913

JW94

JW79

JW77

R848

R844

D919

L702

C705

R851

JW11

JW12

R845

JW88

R709

JR11

TP001

R852

JW139

JW98

C704

R703

R925

JW7

JW86

R810

R903

JW49

IC802

R912

JW85

JW84

R904

JW93

JW81

Q900

R928

R902

R917

JW97

JW96

JW95

C909

D915

JW92

Q907

Q906

JW80

C908

JW8

JW9

Q902

R825

JW87

R835

R914

R915

L900

D912

JW2

R824

JW1

(Page 22)

JW206

JW205

JW202

JW201

JW207

JW204

JW203

JW200

• Semiconductor Location

Ref. No. Location D400 D-4

D600 E-2 D801 J-5 D808 J-10 D810 J-6 D811 I-3 D812 I-3 D813 I-3 D814 I-2 D815 I-2 D816 I-2 D817 I-2 D820 H-5 D902 B-7 D903 B-8 D904 C-6 D905 C-6 D906 C-7 D907 C-7 D908 C-7 D909 C-7 D912 F-10 D914 C-9 D915 E-10 D916 C-8

Ref. No. Location D917 C-8

D919 D-9 D921 D-6 D922 D-6

IC100 B-6 IC401 F-4 IC801 H-7 IC802 H-10

Q400 D-4 Q401 D-4 Q402 C-4 Q403 D-3 Q404 C-3 Q405 C-3 Q406 C-3 Q407 C-3 Q601 E-2 Q800 I-6 Q900 H-10 Q902 E-10 Q906 F-10 Q907 F-10

R615

C108

JW60

JW59

JW58

R604

R603

L602

R815

C619

JR10

D817

C618

JW6

Q601

D815

C620 D600

C450

C451

JW50

D816

JW5

JW130

JW51

R865

D814

JW61

JW52

C303

R415

R864

D813

C444

JW54

R441

R409

JW53

D812

CNP800

Q407

Q404

Q403

R414

C426

C453

D811

C436

R443

R420

C408

JW55

JW128

R440

R436

JW46

C435

C452

R412

JW56

JW44

Q405

Q406

C425

R411

JW45

R416

R435

C409

JW57

R442

C440

R419

JW127

Q401

JW121

D400

R404

S800

JW43

JW132

C424

C416

R406

IC401

R421

C438

R417

R405

JW42

Q402

JR6

R407

JW137

R431

R429

R424

Q400

R808

R800

JW41

JW136

R833

R418

C428

L400

JW40

C437

R432

C430

C417

C411

FMB4

JW39

C106

C400

JR103

JW38

JW28

R447

JW122

JW120

JW66

C410

C414

JW37

JW123

C101

C446

JW36

JW32

C113

JW126

C447

R401

JW63

JW35

R809

JW125

C441

R400

JW62

R813

R834

JW31

JW124

R448

JW67

JW34

C107

R806

JW30

JW33

R821

D820

C824

D801

C111

R828

R819

R801

JW29

JW118

C801

JW64

R818

R823

R832

R805

C823

R862

JW26

R850

JW113

JW117

R927

R861

R830

R822

R837

C802

JW65

C813

C821

R804

JW111

IC100

D904

JW116

JW142

R839

R849

JW71

JW115

JW141

R840

JW112

C810

R841

C807

R826

Q800

D810

R427

D905

C809

JW135

JW138

D922

D921

JW140

JW68

D702

JW114

JW25

D907

JW69

C706

C109

JW24

D906

JW70

IC801

JW23

JW108

JW109

L700

JW76

JW74

JW73

JW143

JW72

R802

JW107

JW106

JW105

R843

JW22

D902

JW110

D908

D909

JW104

C707

JW10

R707

R722

R705

R854

X801

JW21

JW20

(Page 27)

2626

Page 27

3-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 20 for Circuit Boards Location. : Uses unleaded solder.

CDX-R3000/RW300

S509

234567891011 12 13 14

S507

LED507

LED521

LED520

S508

S523

S502

S504

S516

LED513

LED524

LED501

S505

LED525

S506

LED522

S511

LED505

LED504

S512

S521

LED511

LED503

S520

LED510

LCD501

S519

LED509

S518

LED508

LED506

S510

S522

LED518

LED514

LED502

S515

LED512

S517

S501

S513

LED517

LED516

S514

IC502

LED515

S503

R580

R507

R506

R505

R508

R503 R504

R578

R532

R513

R533

R531

R579

• Semiconductor Location

Ref. No. Location D502 F-13

D503 F-11 D504 F-13 D521 G-12 D551 G-10 D552 G-10

IC501 G-7 IC502 C-14 IC906 G-11

LED501 C-4 LED502 C-11

R509

R577

Ref. No. Location LED503 B-8

LED504 D-6 LED505 D-6 LED506 D-10 LED507 A-2 LED508 D-10 LED509 D-9 LED510 D-8 LED511 D-7 LED512 D-12 LED513 C-3 LED514 C-12 LED515 A-13

R510

R576

R537

FMB3

Ref. No. Location LED516 C-13

LED517 B-13 LED518 D-11 LED520 C-2 LED521 B-2 LED522 D-5 LED524 D-3 LED525 D-4

Q501 G-11 Q502 G-10

R536

IC501

R518

C552

R517

R556

R555

R575

R519

R554

R516

FMB4

R557

R553

R574

C960

R515

R514

C553

R561

D551

Q502

D552

R535

Q501

R558

R552

CN901

C959

D503

IC906

(Page 26)

R534

C958

R573

D521

D504

R560

R502

R511

R512

D502

R559

R501

C551

R572

R551

R571

27 27

Page 28

CDX-R3000/RW300

3-14. SCHEMATIC DIAGRAM — DISPLAY SECTION —

(Page 25)

CN901

R534

LED503

R533

R532

R531

D521

S523

D504

D503

D502

R511 R512 R513 R514 R515 R516 R517 R518 R519

S513 S514 S515 S516 S517 S518 S519

R535

R537

R536

Q502

Q501

LED501

LED502

R571

LED515

LED517

LED514

LED516

R572

S520 S521 S522

R573

LED512

LED518

LED506

LED508

R574 R576

R575 R577

LED509

LED510

LED511

LED504

LED505

LED522

LED525

LED524

R578

R579

LED513

LED521

LED507

LED520

R580

R551

IC502

C551

D551

R552

C960

R553

R554

R555

C958

R561

D552

C959

R556 C552

R558

R559

R560

IC906

C553

IC501

R557

R501 R502 R503 R504 R505

S501 S502 S503 S504 S505 S506 S507

LCD501

R506 R507 R508 R509 R510

S508 S509 S510 S511 S512

2828

Page 29

3-15. IC BLOCK DIAGRAMS

IC2 BA5966FP-FE2 (SERVO Board)

REV

OPIN4(+)

OPIN4(–)

2728 26 25

OPOUT4

CDX-R3000/RW300

OPIN3(+)

OPIN3(–)

24 23 22 21 20 19 18 17 16 15

OPOUT3

MUTE

BIAS

GND

VO3(–)

VO3(+)

VO4(–)

VO4(+)

LOADING DRIVER

REV

FWD

+–

OUT F

OUT R

+–+–

4 5 6 7 8 9 10 11 12 13 1421 3

OPIN1(–)

OPOUT1

OPIN1(+)

+–

–

OPIN2(+)

OPIN2(–)

OPOUT2

MUTE

+–

VOL(+)

–

LEVEL

SHIFT

LEVEL

SHIFT

–+

+–

VO2(–)

VO2(+)

–

VCC

VOL(–)

+–

–

LEVEL

SHIFT

LEVEL

SHIFT

–

+–

VO1(–)

+–

VO1(+)

Page 30

CDX-R3000/RW300

IC401 BD3808FS (MAIN Board)

DGND

SDA

32 31 30 29 28 27 26 25 24 23 22

SCL

MUTE

SEL

ADJ

VCC

OUTF1

OUTR1

OUTF2

OUTR2

DS12

DS22

21 20 19 18 17

DS32

OUTS1

OUTS2

C BUS

LOGIC

BASS fo:60,70,80,100,120,140,160,200Hz Q:0.5,0.75,1,1.25

MIDDLE fo:500Hz,1kHz Q:1

TABLE fo:5,7.5,10,12.5kHz

VCO

FADER (0~-58,

-∞dB)

EFFECT (0dB~

+20dB,2dB STEP)

TONE PASS

fc:40kHz fc:40kHz

(0~15dB,1dB STEP)

(4 STEREO INCLUDE 1 ISOLATION INPUT)

FADER (0~-58,

-∞dB)

BASS,TREBLE, MIDDLE

(-15dB~+15dB,1dB STEP)

VOLUME

(+23~-79dB,-∞dB

1dB STEP)

ANTI-ALIASING

FILTER

INPUT GAIN

MUTE

INPUT SELECTOR

TONE PASS

FADER (0~-58,

-∞dB)

EFFECT (0dB~

+20dB,2dB STEP)

BASS,TREBLE, MIDDLE

(-15dB~+15dB,1dB STEP)

VOLUME

(+23~-79dB,-∞dB

1dB STEP)

ANTI-ALIASING

FILTER

INPUT GAIN

(0~15dB,1dB STEP)

MUTE

FADER (0~-58,

-∞dB)

2ND ORDER LPF fc:OFF,80,120,160Hz Q: 0.707

MIX

GAIN+ATT

(+10~-29,

-∞dB)

2ND ORDER

LPF

AGND

VCC/2

6 7 8 9 10 113 4 521

AP1

FIL

AP2

12 14 1613 15

DS11

DS21

DS31

Page 31

NOTE:

• The mechanical parts with no reference number in the exploded views are not supplied.

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• -XX and -X mean standardized parts, so they may have some difference from the original one.

4-1. MAIN SECTION

SECTION 4

EXPLODED VIEWS

• Color Indication of Appearance Parts Example :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinet’s Color

• Accessories are given in the last of this parts list.

•Abbreviation CND : Canadian model

CDX-R3000/RW300

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

MG-611XA-186//K

not supplied

F901

TUX601

not supplied

Ref. No. Part No. Description Remark

1 X-3384-407-1 PANEL (1) ASSY, SUB 23-231-472-01 SCREW (+B 2X4) 3 X-3382-588-1 LOCK ASSY (S)

* 43-246-006-31 COVER

53-922-535-11 SCREW (+BTT)

61-776-206-21 CORD (WITH CONNECTOR) (POWER)

Ref. No. Part No. Description Remark

7 A-3283-418-A MAIN BOARD, COMPLETE (US,CND) 7 A-3283-489-A MAIN BOARD, COMPLETE (E) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A TUX601 A-3220-959-A TUNER UNIT (TUX-032) #1 7-685-792-09 SCREW +PTT 2.6X6 (S)

#2 7-685-793-09 SCREW +PTT 2.6X8 (S)

Page 32

CDX-R3000/RW300

4-2. FRONT PANEL SECTION

LCD901

not supplied

not supplied (DISPLAY board)

not supplied

51 X-3384-410-1 PANEL (BASE) ASSY, FRONT (R3000:US,CND) 51 X-3384-617-1 PANEL (BASE) ASSY, FRONT (RW300) 51 X-3384-687-1 PANEL (BASE) ASSY, FRONT (R3000:E) 52 3-258-879-01 FILTER (IR) 53 3-258-874-01 BUTTON (SEEK)

54 X-3384-070-1 RETRACTABLE ASSY 55 3-258-873-01 BUTTON (+,–) 56 3-246-211-01 SPRING (RELEASE) 57 3-258-884-01 SHEET (ILLUMINATOR) 58 3-258-880-01 PLATE (CD), LIGHT GUIDE

Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark

59 3-258-869-01 PANEL, FRONT BACK 60 X-3378-390-3 CASE ASSY (for FRONT PANEL) 61 A-3372-585-A PANEL OVERALL ASSY, FRONT (R3000:US,CND) 61 A-3372-726-A PANEL OVERALL ASSY, FRONT (RW300) 61 A-3372-777-A PANEL OVERALL ASSY, FRONT (R3000:E)

62 3-258-875-01 BUTTON (PRESET) 63 X-3384-457-1 BUTTON ASSY (S) 64 1-780-120-11 CONDUCTIVE BOARD, CONNECTION LCD901 1-805-450-11 DISPLAY PANEL, LIQUID CRYSTAL #3 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT

Page 33

4-3. CD MECHANISM SECTION (1)

(MG-611XA-186//K)

CDX-R3000/RW300

not supplied

102

not supplied (SENSOR board)

not supplied

101

103

104

106

105

108

107

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

101 A-3372-455-A CHASSIS (T) SUB ASSY 102 3-253-729-01 SPRING (LTR), TENSION COIL 103 3-253-746-01 SPRING (DAMPER), COMPRESSION 104 3-253-746-11 SPRING (DAMPER), COMPRESSION 105 3-253-695-01 SPRING (KF), TENSION COIL

106 3-253-748-01 DAMPER(S) 107 3-352-758-31 SCREW (M1.7), TOOTHED LOCK 108 A-3283-350-A SERVO BOARD, COMPLETE #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

Page 34

CDX-R3000/RW300

4-4. CD MECHANISM SECTION (2)

(MG-611XA-186//K)

154

(including M901)

155

156

157

SW4

151

not supplied

153

152

M902

not supplied

158

not supplied

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

not supplied

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

151 A-3337-637-A CHASSIS (OP) COMPLETE ASSY 152 4-912-432-01 SCREW (B1.4X5), TAPPING

0153 8-820-207-02 OPTICAL PICK-UP KSS1000E/K1RP

154 A-3337-640-A CHASSIS (OP) SUB ASSY (including M901) 155 A-3337-641-A ARM SUB ASSY, CHUCKING

156 A-3337-639-A LEVER (SL) SUB ASSY

157 X-3383-454-2 LEVER (SL) ASSY 158 3-261-959-01 SPRING (SL), TORSION M902 A-3337-638-A MOTOR ASSY, SL (SLED) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT) #5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8

Page 35

4-5. CD MECHANISM SECTION (3)

(MG-611XA-186//K)

CDX-R3000/RW300

209

207

208

201

202

207

M903

210

206

207

203

211

204

205

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

201 3-338-647-31 WASHER (1.0-2.5) 202 3-259-024-01 WHEEL (RA), WORM 203 A-3337-633-A ARM ASSY, ROLLER 204 3-259-455-01 SPRING (RAL) 205 3-253-713-01 SPRING (RAR)

206 3-259-469-01 SPRING (LE), LEAF 207 2-134-636-31 SCREW (M1.7X2.5)

208 3-259-467-01 BRACKET (LEM) 209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK 210 A-3372-456-A WORM (LEB) ASSY 211 3-259-468-01 BEARING (LEB) M903 A-3372-454-A MOTOR ASSY, LE (LOADING)

#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

Page 36

CDX-R3000/RW300

4-6. CD MECHANISM SECTION (4)

(MG-611XA-186//K)

252

254

252

255

256

251

253

257

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

251 3-259-429-01 WHEEL (LE), WORM 252 3-344-223-01 WASHER 253 3-259-470-01 GEAR (LE1) 254 3-253-755-01 LEVER (D)

255 3-899-829-01 WASHER (SLIT) 256 3-259-032-01 GEAR (LE2) 257 A-3372-453-A CHASSIS (M) BLOCK ASSY

Page 37

CDX-R3000/RW300

SECTION 5

ELECTRICAL PARTS LIST

NOTE:

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable

When indicating parts by reference number, please include the board.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

DISPLAY BOARD

**************

1-780-120-11 CONDUCTIVE BOARD, CONNECTION 3-258-884-01 SHEET (ILLUMINATOR)

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORS uF : µF

• COILS uH : µH

•Abbreviation CND : Canadian model

LED507 6-500-510-01 LED CL-195PG-CD-T (ATT) (RW300) LED507 8-719-053-09 LED SML-310VT-T86 (ATT) (R3000) LED508 6-500-510-01 LED CL-195PG-CD-T (6) (RW300) LED508 8-719-053-09 LED SML-310VT-T86 (6) (R3000) LED509 6-500-510-01 LED CL-195PG-CD-T (5) (RW300)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

DISPLAY

< CAPACITOR >

C551 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C552 1-162-963-11 CERAMIC CHIP 680PF 10% 50V C553 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C958 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C959 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V

C960 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CN901 1-794-312-21 PIN, CONNECTOR 12P

< DIODE >

D502 8-719-978-33 DIODE DTZ-TT11-6.8B D503 8-719-978-33 DIODE DTZ-TT11-6.8B D504 8-719-978-33 DIODE DTZ-TT11-6.8B D521 8-719-988-61 DIODE 1SS355TE-17 D551 8-719-069-54 DIODE UDZS-TE17-5.1B

D552 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC501 6-705-180-01 IC LC75827W IC502 6-600-321-01 IC KSM-401Y (IR) IC906 6-705-374-01 IC MM3033DULE

< LIQUID CRYSTAL DISPLAY >

LCD901 1-805-450-11 DISPLAY PANEL, LIQUID CRYSTAL

LED509 8-719-053-09 LED SML-310VT-T86 (5) (R3000) LED510 6-500-510-01 LED CL-195PG-CD-T (4) (RW300) LED510 8-719-053-09 LED SML-310VT-T86 (4) (R3000) LED511 6-500-510-01 LED CL-195PG-CD-T (3) (RW300) LED511 8-719-053-09 LED SML-310VT-T86 (3) (R3000)

LED512 6-500-510-01 LED CL-195PG-CD-T (SHUF) (RW300) LED512 8-719-053-09 LED SML-310VT-T86 (SHUF) (R3000) LED513 6-500-510-01 LED CL-195PG-CD-T (DSPL) (RW300) LED513 8-719-053-09 LED SML-310VT-T86 (DSPL) (R3000) LED514 6-500-510-01 LED CL-195PG-CD-T (EQ3) (RW300)

LED514 8-719-053-09 LED SML-310VT-T86 (EQ3) (R3000) LED515 6-500-510-01 LED CL-195PG-CD-T (OFF) (RW300) LED515 8-719-053-09 LED SML-310VT-T86 (OFF) (R3000) LED516 6-500-510-01 LED CL-195PG-CD-T (SEEK – m .)

(RW300)

LED516 8-719-053-09 LED SML-310VT-T86 (SEEK – m .)

(R3000)

LED517 6-500-510-01 LED CL-195PG-CD-T (SEEK + > M)

(RW300)

LED517 8-719-053-09 LED SML-310VT-T86 (SEEK + > M)

(R3000) LED518 6-500-510-01 LED CL-195PG-CD-T (REP) (RW300) LED518 8-719-053-09 LED SML-310VT-T86 (REP) (R3000) LED520 6-500-510-01 LED CL-195PG-CD-T (VOLUME –) (RW300)

LED520 8-719-053-09 LED SML-310VT-T86 (VOLUME –) (R3000) LED521 6-500-510-01 LED CL-195PG-CD-T (VOLUME +) (RW300) LED521 8-719-053-09 LED SML-310VT-T86 (VOLUME +) (R3000) LED522 6-500-510-01 LED CL-195PG-CD-T (SEL) (RW300) LED522 8-719-053-09 LED SML-310VT-T86 (SEL) (R3000)

< DIODE >

LED501 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) LED502 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) LED503 6-500-511-01 LED CL-270PG-C-TS (DISC IND) (RW300) LED503 8-719-082-38 LED CL-270SR-C-TS (DISC IND) (R3000) LED504 6-500-510-01 LED CL-195PG-CD-T (2) (RW300)

LED504 8-719-053-09 LED SML-310VT-T86 (2) (R3000) LED505 6-500-510-01 LED CL-195PG-CD-T (1) (RW300) LED505 8-719-053-09 LED SML-310VT-T86 (1) (R3000) LED506 6-500-510-01 LED CL-195PG-CD-T (SENS) (RW300) LED506 8-719-053-09 LED SML-310VT-T86 (SENS) (R3000)

LED524 6-500-510-01 LED CL-195PG-CD-T (SOURCE) (RW300) LED524 8-719-053-09 LED SML-310VT-T86 (SOURCE) (R3000) LED525 6-500-510-01 LED CL-195PG-CD-T (MODE) (RW300) LED525 8-719-053-09 LED SML-310VT-T86 (MODE) (R3000)

< TRANSISTOR >

Q501 8-729-900-53 TRANSISTOR DTC114EK Q502 8-729-900-53 TRANSISTOR DTC114EK

< RESISTOR >

R501 1-216-819-11 METAL CHIP 680 5% 1/10W

Page 38

CDX-R3000/RW300

DISPLAY MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R502 1-216-819-11 METAL CHIP 680 5% 1/10W R503 1-216-819-11 METAL CHIP 680 5% 1/10W R504 1-216-821-11 METAL CHIP 1K 5% 1/10W R505 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R506 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R507 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R508 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R509 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R510 1-218-867-11 METAL CHIP 6.8K 5% 1/10W R511 1-216-819-11 METAL CHIP 680 5% 1/10W

R512 1-216-819-11 METAL CHIP 680 5% 1/10W R513 1-216-819-11 METAL CHIP 680 5% 1/10W R514 1-216-821-11 METAL CHIP 1K 5% 1/10W R515 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R516 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R577 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R577 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R578 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R578 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R579 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R579 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R580 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R580 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R517 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R518 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R519 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R531 1-216-809-11 METAL CHIP 100 5% 1/10W R532 1-216-809-11 METAL CHIP 100 5% 1/10W

R533 1-216-809-11 METAL CHIP 100 5% 1/10W R534 1-216-826-11 METAL CHIP 2.7K 5% 1/10W R535 1-216-826-11 METAL CHIP 2.7K 5% 1/10W R536 1-216-813-11 METAL CHIP 220 5% 1/10W R537 1-216-813-11 METAL CHIP 220 5% 1/10W

R551 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R552 1-216-815-11 METAL CHIP 330 5% 1/10W R553 1-216-821-11 METAL CHIP 1K 5% 1/10W R554 1-216-821-11 METAL CHIP 1K 5% 1/10W R555 1-216-821-11 METAL CHIP 1K 5% 1/10W

R556 1-216-840-11 METAL CHIP 39K 5% 1/10W R557 1-216-821-11 METAL CHIP 1K 5% 1/10W R558 1-216-821-11 METAL CHIP 1K 5% 1/10W R559 1-216-821-11 METAL CHIP 1K 5% 1/10W R560 1-216-821-11 METAL CHIP 1K 5% 1/10W

R561 1-216-857-11 METAL CHIP 1M 5% 1/10W R571 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R571 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R572 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R572 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R573 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R573 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R574 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R574 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R575 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R575 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R576 1-216-808-11 METAL CHIP 82 5% 1/10W

(RW300)

R576 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

< SWITCH >

S501 1-786-653-11 SWITCH, TACTILE (OPEN/EJECT) S502 1-786-653-11 SWITCH, TACTILE (OPEN/EJECT) S503 1-771-884-31 SWITCH, TACTILE (OFF) S504 1-771-884-31 SWITCH, TACTILE (SOURCE) S505 1-771-884-31 SWITCH, TACTILE (MODE)

S506 1-771-884-31 SWITCH, TACTILE (SEL) S507 1-771-884-31 SWITCH, TACTILE (VOLUME +) S508 1-771-884-31 SWITCH, TACTILE (VOLUME –) S509 1-771-884-31 SWITCH, TACTILE (ATT) S510 1-771-884-31 SWITCH, TACTILE (BTM/SENS)

S511 1-771-884-31 SWITCH, TACTILE (1) S512 1-771-884-31 SWITCH, TACTILE (2) S513 1-771-884-31 SWITCH, TACTILE (SEEK + > M) S514 1-771-884-31 SWITCH, TACTILE (SEEK – m .) S515 1-771-884-31 SWITCH, TACTILE (EQ3)

S516 1-771-884-31 SWITCH, TACTILE (DSPL) S517 1-771-884-31 SWITCH, TACTILE (SHUF) S518 1-771-884-31 SWITCH, TACTILE (6) S519 1-771-884-31 SWITCH, TACTILE (5) S520 1-771-884-31 SWITCH, TACTILE (4)

S521 1-771-884-31 SWITCH, TACTILE (3) S522 1-771-884-31 SWITCH, TACTILE (REP) S523 1-529-566-61 SWITCH, PUSH (1 KEY) (OPEN/EJECT)

*************************************************************

A-3283-418-A MAIN BOARD, COMPLETE (including

SPEAKER BOARD) (US,CND)

A-3283-489-A MAIN BOARD, COMPLETE (including

SPEAKER BOARD) (E)

*********************

7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-793-09 SCREW +PTT 2.6X8 (S) 7-685-795-09 SCREW +PTT 2.6X12 (S)

< CAPACITOR >

C101 1-124-233-11 ELECT 10uF 20% 16V C106 1-124-234-00 ELECT 22uF 20% 16V C107 1-124-233-11 ELECT 10uF 20% 16V C108 1-216-864-11 METAL CHIP 0 5% 1/10W C109 1-124-233-11 ELECT 10uF 20% 16V

C111 1-124-233-11 ELECT 10uF 20% 16V C113 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V

Page 39

CDX-R3000/RW300

MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C303 1-216-864-11 METAL CHIP 0 5% 1/10W C400 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C406 1-136-154-00 FILM 0.012uF 5% 50V C407 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C408 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V

C409 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C410 1-104-942-11 ELECT 1uF 20% 50V C411 1-104-942-11 ELECT 1uF 20% 50V C414 1-128-428-11 ELECT 10uF 20% 35V C416 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C908 1-126-960-11 ELECT 1uF 20% 50V

C909 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C922 1-131-868-81 ELECT 3300uF 20% 16V

< CONNECTOR >

CN751 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P CNP800 1-794-311-21 PLUG, CONNECTOR 12P CNP900 1-764-270-21 JACK (REMOTE IN) (E) CNP901 1-774-701-21 PIN, CONNECTOR 16P

(E)

C417 1-124-589-11 ELECT 47uF 20% 16V C424 1-128-428-11 ELECT 10uF 20% 35V C425 1-128-428-11 ELECT 10uF 20% 35V C426 1-128-428-11 ELECT 10uF 20% 35V C428 1-128-428-11 ELECT 10uF 20% 35V

C430 1-126-947-11 ELECT 47uF 20% 16V C435 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C436 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C437 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C438 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V

C440 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C441 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C444 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C446 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C447 1-124-257-00 ELECT 2.2uF 20% 50V

C450 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C451 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C452 1-128-428-11 ELECT 10uF 20% 35V C453 1-128-428-11 ELECT 10uF 20% 35V C600 1-216-864-11 METAL CHIP 0 5% 1/10W

C618 1-126-786-11 ELECT 47uF 20% 16V C619 1-124-247-61 ELECT 10uF 20% 35V C620 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C701 1-124-584-00 ELECT 100uF 20% 10V C704 1-124-584-00 ELECT 100uF 20% 10V

C705 1-124-584-00 ELECT 100uF 20% 10V C706 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C707 1-124-584-00 ELECT 100uF 20% 10V C709 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C801 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C802 1-124-589-11 ELECT 47uF 20% 16V C807 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C809 1-124-584-00 ELECT 100uF 20% 10V C810 1-125-701-11 DOUBLE LAYERS 0.047F 5.5V C812 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C813 1-124-584-00 ELECT 100uF 20% 10V C815 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C816 1-164-160-11 CERAMIC CHIP 20PF 5% 50V C817 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C818 1-164-160-11 CERAMIC CHIP 20PF 5% 50V

C820 1-162-920-11 CERAMIC CHIP 27PF 5% 50V C821 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C822 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C823 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C824 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

< DIODE >

D400 8-719-988-61 DIODE 1SS355TE-17 D600 8-719-069-55 DIODE UDZS-TE17-5.6B D702 1-216-864-11 METAL CHIP 0 5% 1/10W D801 8-719-988-61 DIODE 1SS355TE-17 D808 8-719-977-12 DIODE DTZ6.8B

D810 8-719-988-61 DIODE 1SS355TE-17 (E) D811 8-719-109-97 DIODE RD6.8ES-B2 D812 8-719-109-97 DIODE RD6.8ES-B2 D813 8-719-109-97 DIODE RD6.8ES-B2 D814 8-719-109-97 DIODE RD6.8ES-B2

D815 8-719-109-97 DIODE RD6.8ES-B2 D816 8-719-109-97 DIODE RD6.8ES-B2 D817 8-719-109-97 DIODE RD6.8ES-B2 D820 8-719-991-33 DIODE 1SS133T-77 D902 8-719-053-18 DIODE 1SR154-400TE-25

D903 8-719-053-18 DIODE 1SR154-400TE-25 D904 8-719-200-82 DIODE 11ES2 D905 8-719-200-82 DIODE 11ES2 D906 8-719-200-82 DIODE 11ES2 D907 8-719-200-82 DIODE 11ES2

D908 8-719-200-82 DIODE 11ES2 D909 8-719-200-82 DIODE 11ES2 D912 8-719-083-66 DIODE UDZSTE-1718B D914 8-719-977-12 DIODE DTZ6.8B D915 8-719-056-84 DIODE UDZSTE-177.5B

D916 8-719-200-82 DIODE 11ES2 D917 8-719-200-82 DIODE 11ES2 D919 8-719-049-38 DIODE 1N5404TU D921 8-719-200-82 DIODE 11ES2 D922 8-719-200-82 DIODE 11ES2

< IC >

IC100 6-705-360-01 IC TDA8588BJ/N2 IC401 6-705-372-01 IC BD3808FS-FE2 IC801 6-803-820-01 IC MB90473PF-G166-BNDE1 IC802 8-759-659-13 IC PST3428UL

< JUMPER RESISTOR >

JR5 1-216-864-11 METAL CHIP 0 5% 1/10W JR6 1-216-864-11 METAL CHIP 0 5% 1/10W JR10 1-216-864-11 METAL CHIP 0 5% 1/10W JR11 1-216-864-11 METAL CHIP 0 5% 1/10W JR103 1-216-864-11 METAL CHIP 0 5% 1/10W

C825 1-124-584-00 ELECT 100uF 20% 10V C908 1-126-160-11 ELECT 1uF 20% 50V

(US,CND)

Page 40

CDX-R3000/RW300

MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

< COIL >

L400 1-414-398-11 INDUCTOR 10uH L602 1-414-394-41 INDUCTOR 2.2uH L700 1-410-501-11 INDUCTOR 2.2uH L701 1-410-501-11 INDUCTOR 2.2uH L702 1-410-509-11 INDUCTOR 10uH

L900 1-456-617-11 COIL, CHOKE 250uH

< JACK >

R448 1-216-841-11 METAL CHIP 47K 5% 1/10W R603 1-247-807-31 CARBON 100 5% 1/4W R604 1-247-807-31 CARBON 100 5% 1/4W R606 1-216-809-11 METAL CHIP 100 5% 1/10W R607 1-216-809-11 METAL CHIP 100 5% 1/10W

R608 1-216-809-11 METAL CHIP 100 5% 1/10W R615 1-216-821-11 METAL CHIP 1K 5% 1/10W R703 1-216-864-11 METAL CHIP 0 5% 1/10W R705 1-216-809-11 METAL CHIP 100 5% 1/10W R707 1-216-809-11 METAL CHIP 100 5% 1/10W

PJ401 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR) PJ601 1-793-598-11 JACK (ANTENNA)

< TRANSISTOR >

Q400 8-729-038-71 TRANSISTOR KRC107S Q401 8-729-038-55 TRANSISTOR KRA103S Q402 6-550-752-01 TRANSISTOR DTC614TKT146 Q403 6-550-752-01 TRANSISTOR DTC614TKT146 Q404 6-550-752-01 TRANSISTOR DTC614TKT146

Q405 6-550-752-01 TRANSISTOR DTC614TKT146 Q406 6-550-752-01 TRANSISTOR DTC614TKT146 Q407 6-550-752-01 TRANSISTOR DTC614TKT146 Q601 8-729-920-85 TRANSISTOR 2SD1664-QR Q800 8-729-038-55 TRANSISTOR KRA103S

Q900 8-729-034-51 TRANSISTOR KTC3875 Q902 8-729-038-67 TRANSISTOR KRC102S Q906 8-729-034-51 TRANSISTOR KTC3875 Q907 8-729-038-67 TRANSISTOR KRC102S

< RESISTOR >

R404 1-216-809-11 METAL CHIP 100 5% 1/10W R405 1-216-809-11 METAL CHIP 100 5% 1/10W R406 1-216-809-11 METAL CHIP 100 5% 1/10W R407 1-216-809-11 METAL CHIP 100 5% 1/10W R409 1-216-839-11 METAL CHIP 33K 5% 1/10W

R411 1-216-809-11 METAL CHIP 100 5% 1/10W R412 1-216-809-11 METAL CHIP 100 5% 1/10W R414 1-216-809-11 METAL CHIP 100 5% 1/10W R415 1-216-809-11 METAL CHIP 100 5% 1/10W R416 1-216-809-11 METAL CHIP 100 5% 1/10W

R417 1-216-809-11 METAL CHIP 100 5% 1/10W R418 1-216-841-11 METAL CHIP 47K 5% 1/10W R419 1-216-841-11 METAL CHIP 47K 5% 1/10W R420 1-216-841-11 METAL CHIP 47K 5% 1/10W R421 1-216-841-11 METAL CHIP 47K 5% 1/10W

R424 1-216-805-11 METAL CHIP 47 5% 1/10W R427 1-216-809-11 METAL CHIP 100 5% 1/10W R429 1-247-807-31 CARBON 100 5% 1/4W R431 1-247-807-31 CARBON 100 5% 1/4W R432 1-216-809-11 METAL CHIP 100 5% 1/10W

R435 1-216-809-11 METAL CHIP 100 5% 1/10W R436 1-216-809-11 METAL CHIP 100 5% 1/10W R437 1-216-821-11 METAL CHIP 1K 5% 1/10W R440 1-216-809-11 METAL CHIP 100 5% 1/10W R441 1-216-809-11 METAL CHIP 100 5% 1/10W

R442 1-216-841-11 METAL CHIP 47K 5% 1/10W R443 1-216-841-11 METAL CHIP 47K 5% 1/10W R447 1-216-809-11 METAL CHIP 100 5% 1/10W

R709 1-216-864-11 METAL CHIP 0 5% 1/10W R722 1-216-809-11 METAL CHIP 100 5% 1/10W R800 1-216-841-11 METAL CHIP 47K 5% 1/10W

(E) R801 1-216-809-11 METAL CHIP 100 5% 1/10W R802 1-216-864-11 METAL CHIP 0 5% 1/10W

R804 1-216-809-11 METAL CHIP 100 5% 1/10W R805 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R806 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R808 1-216-845-11 METAL CHIP 100K 5% 1/10W

(E) R808 1-216-864-11 METAL CHIP 0 5% 1/10W

(US,CND)

R809 1-216-845-11 METAL CHIP 100K 5% 1/10W

(E) R810 1-216-845-11 METAL CHIP 100K 5% 1/10W R811 1-216-845-11 METAL CHIP 100K 5% 1/10W R813 1-249-441-11 CARBON 100K 5% 1/4W R814 1-216-845-11 METAL CHIP 100K 5% 1/10W

R815 1-249-435-11 CARBON 33K 5% 1/4W R818 1-216-809-11 METAL CHIP 100 5% 1/10W R819 1-216-809-11 METAL CHIP 100 5% 1/10W R821 1-216-817-11 METAL CHIP 470 5% 1/10W R822 1-216-817-11 METAL CHIP 470 5% 1/10W

R823 1-216-817-11 METAL CHIP 470 5% 1/10W R824 1-216-849-11 METAL CHIP 220K 5% 1/10W R825 1-216-849-11 METAL CHIP 220K 5% 1/10W R826 1-216-843-11 METAL CHIP 68K 5% 1/10W R828 1-216-809-11 METAL CHIP 100 5% 1/10W

R830 1-216-809-11 METAL CHIP 100 5% 1/10W R832 1-216-867-11 METAL CHIP 6.8K 5% 1/10W R833 1-249-417-11 CARBON 1K 5% 1/4W R834 1-216-867-11 METAL CHIP 6.8K 5% 1/10W R835 1-216-845-11 METAL CHIP 100K 5% 1/10W

R837 1-216-864-11 METAL CHIP 0 5% 1/10W R838 1-216-845-11 METAL CHIP 100K 5% 1/10W R839 1-216-809-11 METAL CHIP 100 5% 1/10W R840 1-216-809-11 METAL CHIP 100 5% 1/10W R841 1-216-809-11 METAL CHIP 100 5% 1/10W

R843 1-216-809-11 METAL CHIP 100 5% 1/10W R844 1-216-845-11 METAL CHIP 100K 5% 1/10W R846 1-216-845-11 METAL CHIP 100K 5% 1/10W R847 1-216-845-11 METAL CHIP 100K 5% 1/10W R848 1-216-845-11 METAL CHIP 100K 5% 1/10W

R849 1-216-841-11 METAL CHIP 47K 5% 1/10W R850 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R851 1-216-809-11 METAL CHIP 100 5% 1/10W R852 1-216-864-11 METAL CHIP 0 5% 1/10W R853 1-216-864-11 METAL CHIP 0 5% 1/10W

Page 41

CDX-R3000/RW300

MAIN SENSOR SERVO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R854 1-216-864-11 METAL CHIP 0 5% 1/10W R860 1-216-845-11 METAL CHIP 100K 5% 1/10W R861 1-216-809-11 METAL CHIP 100 5% 1/10W

R862 1-216-809-11 METAL CHIP 100 5% 1/10W

R864 1-249-441-11 CARBON 100K 5% 1/4W

R865 1-249-441-11 CARBON 100K 5% 1/4W R873 1-216-845-11 METAL CHIP 100K 5% 1/10W R901 1-216-845-11 METAL CHIP 100K 5% 1/10W R902 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R903 1-216-841-11 METAL CHIP 47K 5% 1/10W

R904 1-216-841-11 METAL CHIP 47K 5% 1/10W R912 1-249-417-11 CARBON 1K 5% 1/4W R913 1-216-821-11 METAL CHIP 1K 5% 1/10W R914 1-469-144-21 FERRITE, EMI (SMD) (E) R915 1-469-144-21 FERRITE, EMI (SMD) (E)

R917 1-249-421-11 CARBON 2.2K 5% 1/4W R925 1-216-845-11 METAL CHIP 100K 5% 1/10W R927 1-216-833-11 METAL CHIP 10K 5% 1/10W R928 1-249-421-11 CARBON 2.2K 5% 1/4W R931 1-216-073-00 RES-CHIP 10K 5% 1/10W

R932 1-216-073-00 RES-CHIP 10K 5% 1/10W R936 1-216-864-11 METAL CHIP 0 5% 1/10W

< SWITCH >

S800 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (E) S802 1-762-638-21 SWITCH, TACTILE (RESET)

< TUNER >

TUX601 A-3220-959-A TUNER UNIT (TUX-032)

< VIBRATOR >

C18 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C19 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

(E)

C21 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C23 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

(E)

C25 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V C26 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C27 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C28 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C29 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C30 1-162-921-11 CERAMIC CHIP 33PF 5% 50V C31 1-162-925-11 CERAMIC CHIP 68PF 5% 50V C32 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C34 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C36 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C38 1-104-609-11 ELECT CHIP 100uF 20% 4V C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C70 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V

C71 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C72 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C73 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C74 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C75 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C76 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C77 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C78 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C79 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V

< CONNECTOR >

CN1 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P CN2 1-794-153-21 CONNECTOR, FPC (ZIF) 16P

X800 1-767-993-21 VIBRATOR, CRYSTAL (3.68MHz) X801 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

SENSOR BOARD

**************

< SWITCH >

SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF) SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)

*************************************************************

A-3283-350-A SERVO BOARD, COMPLETE

**********************

< CAPACITOR >

C1 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C2 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C3 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C5 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C6 1-100-381-11 ELECT CHIP 10uF 20% 16V

C7 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C8 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C13 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C17 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< FERRITE BEAD >

FB1 1-414-760-21 FERRITE, EMI (SMD)

< IC >

IC1 6-703-699-01 IC uPD63712GC-8EU-A IC2 6-705-002-01 IC BA5966FP-FE2

< FERRITE BEAD >

JR40 1-414-760-21 FERRITE, EMI (SMD) JR41 1-414-760-21 FERRITE, EMI (SMD) JR90 1-414-760-21 FERRITE, EMI (SMD) JR91 1-414-760-21 FERRITE, EMI (SMD)

< TRANSISTOR >

Q1 8-729-904-87 TRANSISTOR 2SB1197K-R

< RESISTOR >

R1 1-216-841-11 METAL CHIP 47K 5% 1/10W R6 1-216-833-11 METAL CHIP 10K 5% 1/10W R7 1-216-840-11 METAL CHIP 39K 5% 1/10W R9 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R11 1-216-833-11 METAL CHIP 10K 5% 1/10W

R12 1-216-809-11 METAL CHIP 100 5% 1/10W

Page 42

CDX-R3000/RW300

SERVO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R13 1-216-833-11 METAL CHIP 10K 5% 1/10W R14 1-216-797-11 METAL CHIP 10 5% 1/10W R15 1-216-797-11 METAL CHIP 10 5% 1/10W R41 1-216-821-11 METAL CHIP 1K 5% 1/10W R42 1-216-821-11 METAL CHIP 1K 5% 1/10W

R44 1-414-760-21 FERRITE, EMI (SMD) R45 1-414-760-21 FERRITE, EMI (SMD) R70 1-216-842-11 METAL CHIP 56K 5% 1/10W R71 1-216-833-11 METAL CHIP 10K 5% 1/10W R72 1-216-842-11 METAL CHIP 56K 5% 1/10W

R73 1-216-833-11 METAL CHIP 10K 5% 1/10W R74 1-216-837-11 METAL CHIP 22K 5% 1/10W R75 1-216-833-11 METAL CHIP 10K 5% 1/10W R76 1-216-837-11 METAL CHIP 22K 5% 1/10W R77 1-216-833-11 METAL CHIP 10K 5% 1/10W

R78 1-216-833-11 METAL CHIP 10K 5% 1/10W R79 1-216-833-11 METAL CHIP 10K 5% 1/10W R80 1-216-833-11 METAL CHIP 10K 5% 1/10W R81 1-216-833-11 METAL CHIP 10K 5% 1/10W R82 1-216-837-11 METAL CHIP 22K 5% 1/10W

R83 1-216-833-11 METAL CHIP 10K 5% 1/10W R84 1-216-837-11 METAL CHIP 22K 5% 1/10W R85 1-216-833-11 METAL CHIP 10K 5% 1/10W

< SWITCH >

SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)

< VIBRATOR >

3-261-844-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH)

3-261-844-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH,

3-261-844-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH)

3-261-846-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

3-261-846-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

3-261-846-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

X-3378-390-3 CASE ASSY (for FRONT PANEL)

*************************************************************

PARTS FOR INSTALLATION AND CONNECTIONS

***************************************

301 X-3382-647-1 FRAME ASSY, FITTING 302 X-3366-405-1 SCREW ASSY (EXP), FITTING (E) 303 3-934-325-01 SCREW (+K 5X8 TP) 304 3-260-282-01 COLLAR 305 3-246-471-01 KEY (FRAME)

306 1-776-206-21 CORD (WITH CONNECTOR) (POWER)

ACCESSORIES

************

(R3000:US,CND)

TRADITIONAL CHINESE) (R3000:E)

(RW300)

FRENCH) (R3000:US,CND)

SPANISH,TRADITIONAL CHINESE)

(R3000:E)

SPANISH) (RW300)

302301

X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz)

*************************************************************

MISCELLANEOUS

***************

6 1-776-206-21 CORD (WITH CONNECTOR) (POWER)

0153 8-820-207-02 OPTICAL PICK-UP KSS1000E/K1RP

154 A-3337-640-A CHASSIS (OP) SUB ASSY (including M901) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A M902 A-3337-638-A MOTOR ASSY, SL (SLED)

M903 A-3372-454-A MOTOR ASSY, LE (LOADING) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)

*************************************************************

305303 306304

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

Page 43

CDX-R3000/RW300

US Model

CDX-R3000/RW300

Canadian Model

SERVICE MANUAL

Ver. 1.1 2005.07

SUPPLEMENT-1

File this supplement with the service manual.

Subject : Change of display board.

When performing service and inspection, check the suffix of the part number of the display board.

DISCRIMINATION

– DISPLAY BOARD (SIDE B) –

E Model

CDX-R3000

9-961-386-81

DISPLAY BOARD Part No. Former : 1-861-024-11 New : 1-861-024-13

Page 44

CDX-R3000/RW300

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)

For schematic diagrams.

Note:

• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/ specified.

•

• C : panel designation.

Note:

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

• A : B+ Line.

• B : B– Line.

• H : adjustment for repair.

•Voltages and waveforms are dc with respect to ground

• CD mechanism section

no mark : CD PLAY

• Main (1/2), (2/2) and Display sections

no mark : FM

: internal component.

under no-signal (detuned) conditions.

(): AM <>: CD PLAY

W or less unless otherwise

Note:

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

∗ : Impossible to measure

•Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.

•Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances.

• Circled numbers refer to waveforms.

• Signal path.

J : CD PLAY F : FM f : AM

•Abbreviation CND : Canadian model.

For printed wiring boards.

Note:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

•

• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Par ts face side: Parts on the parts face side seen from the (Side A) parts face are indicated.

•Abbreviation

: Through hole.

These are omitted

CND : Canadian model.

Page 45

CDX-R3000/RW300

1. PRINTED WIRING BOARD — DISPLAY SECTION —

234567891011 12 13 14

LED507

S509

S507

LED521

S516

S522

LED513

LED501

LED520

S508

S502

S504

LED524

: Uses unleaded solder.

LED525

S505 S523S510S518S519S520S521S512S511S506

LED522

LED505 LED506LED508LED509LED510LED511LED504

LED503

LCD501

LED518

LED502

LED514

S517

S515

LED512

S501

S513

LED517

LED516

S514

S503

LED515

IC502

R580

R507

R506

R505

R508

R503

R578

R513

R533

R532

R504

R531

R579

• Semiconductor Location

Ref. No. Location D502 F-13

D503 F-11 D504 F-13 D551 G-10 D552 G-10

IC501 G-7 IC502 C-14 IC906 G-11

LED501 C-4 LED502 C-11

Ref. No. Location LED503 B-8

LED504 D-6 LED505 D-6 LED506 D-10 LED507 A-2 LED508 D-10 LED509 D-9 LED510 D-8 LED511 D-7 LED512 D-12 LED513 C-3 LED514 C-12

R510

R509

R577

FMB3

Ref. No. Location LED515 A-13

LED516 C-13 LED517 B-13 LED518 D-11 LED520 C-2 LED521 B-2 LED522 D-5 LED524 D-3 LED525 D-4

Q502 G-10

R576

R537

R536

R518

IC501

C552

R517

R519

R556

R555

R575

R516

R554

R557

R553

R574

R514

C553

C960

R515

R561

D551

D552

R535

Q502

R558

R552

CN901

IC906

D503

C958

R573

D504

R560

R502

R559

R512

R511

D502

R501

C551

R572

R551

R571

Page 46

CDX-R3000/RW300

2. SCHEMATIC DIAGRAM — DISPLAY SECTION —

CN901

LED503

R533

R532

R531

S522

D502

D503

D504

R511 R512 R513 R514 R515 R516 R517 R518 R519

R535

LED501

R537

R536

LED502

Q502

R571

LED515

LED517

LED514

LED516

R572

R573

LED512

LED518

LED506

LED508

R574 R576

R575 R577

LED509

LED510

LED511

LED504

LED505

LED522

LED525

LED524

R578

R579

LED513

LED521

LED507

LED520

R580

R551

IC502

C551

D551

R552

C960

R553

R554

R555

R561

D552

C958

R556

R558 R559 R560

IC906

IC501

C552

R557

C553

S513 S514 S515 S516 S517 S518 S519 S520 S521 S523

R501

R502 R503 R504 R505 R506 R507 R508 R509 R510

S501 S502 S503 S504 S505 S506 S507 S508 S509 S510 S511 S512

LCD501

Page 47

CDX-R3000/RW300

DISPLAY

3. ELECTRICAL PARTS LIST

NOTE:

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable

•Abbreviation CND : Canadian model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

DISPLAY BOARD

**************

1-780-120-11 CONDUCTIVE BOARD, CONNECTION 3-258-884-01 SHEET (ILLUMINATOR)

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORS uF : µF

• COILS uH : µH

LED508 8-719-053-09 LED SML-310VTT86 (8) (R3000) LED509 6-500-510-01 LED CL-195PG-CD-T (5) (RW300) LED509 8-719-053-09 LED SML-310VTT86 (5) (R3000) LED510 6-500-510-01 LED CL-195PG-CD-T (4) (RW300) LED510 8-719-053-09 LED SML-310VTT86 (4) (R3000)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

When indicating parts by reference number, please include the board.

< CAPACITOR >

< CONNECTOR >

CN901 1-794-312-21 PIN, CONNECTOR 12P

< DIODE >

D502 8-719-977-12 DIODE DTZ6.8B D503 8-719-977-12 DIODE DTZ6.8B D504 8-719-977-12 DIODE DTZ6.8B D551 8-719-080-28 DIODE KDZ5.1V D552 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC501 6-705-180-01 IC LC75827W IC502 6-600-384-01 IC KSM-401E (IR) IC906 6-705-374-01 IC MM3033DULE

< LIQUID CRYSTAL DISPLAY >

LCD501 1-805-450-11 DISPLAY PANEL, LIQUID CRYSTAL

< LED >

LED501 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) LED502 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) LED503 6-500-510-01 LED CL-195PG-CD-T (DISC IND) (RW300) LED503 8-719-053-09 LED SML-310VTT86 (DISC IND) (R3000) LED504 6-500-510-01 LED CL-195PG-CD-T (2) (RW300)

LED511 6-500-510-01 LED CL-195PG-CD-T (3) (RW300) LED511 8-719-053-09 LED SML-310VTT86 (3) (R3000) LED512 6-500-510-01 LED CL-195PG-CD-T (SHUF) (RW300) LED512 8-719-053-09 LED SML-310VTT86 (SHUF) (R3000) LED513 6-500-510-01 LED CL-195PG-CD-T (DSPL) (RW300)

LED513 8-719-053-09 LED SML-310VTT86 (DSPL) (R3000) LED514 6-500-510-01 LED CL-195PG-CD-T (EQ3) (RW300) LED514 8-719-053-09 LED SML-310VTT86 (EQ3) (R3000) LED515 6-500-510-01 LED CL-195PG-CD-T (OFF) (RW300) LED515 8-719-053-09 LED SML-310VTT86 (OFF) (R3000)

LED516 6-500-510-01 LED CL-195PG-CD-T (SEEK – m .)

(RW300)

LED516 8-719-053-09 LED SML-310VTT86 (SEEK – m .)

(R3000)

LED517 6-500-510-01 LED CL-195PG-CD-T (SEEK + > M)

(RW300)

LED517 8-719-053-09 LED SML-310VTT86 (SEEK + > M)

(R3000)

LED518 6-500-510-01 LED CL-195PG-CD-T (REP) (RW300)

LED518 8-719-053-09 LED SML-310VTT86 (REP) (R3000) LED520 6-500-510-01 LED CL-195PG-CD-T (VOLUME –) (RW300) LED520 8-719-053-09 LED SML-310VTT86 (VOLUME –) (R3000) LED521 6-500-510-01 LED CL-195PG-CD-T (VOLUME +) (RW300) LED521 8-719-053-09 LED SML-310VTT86 (VOLUME +) (R3000)

LED522 6-500-510-01 LED CL-195PG-CD-T (SEL) (RW300) LED522 8-719-053-09 LED SML-310VTT86 (SEL) (R3000) LED524 6-500-510-01 LED CL-195PG-CD-T (SOURCE) (RW300) LED524 8-719-053-09 LED SML-310VTT86 (SOURCE) (R3000) LED525 6-500-510-01 LED CL-195PG-CD-T (MODE) (RW300)

LED525 8-719-053-09 LED SML-310VTT86 (MODE) (R3000)

< TRANSISTOR >

LED504 8-719-053-09 LED SML-310VTT86 (2) (R3000) LED505 6-500-510-01 LED CL-195PG-CD-T (1) (RW300) LED505 8-719-053-09 LED SML-310VTT86 (1) (R3000) LED506 6-500-510-01 LED CL-195PG-CD-T (SENS) (RW300) LED506 8-719-053-09 LED SML-310VTT86 (SENS) (R3000)

LED507 6-500-510-01 LED CL-195PG-CD-T (ATT) (RW300) LED507 8-719-053-09 LED SML-310VTT86 (ATT) (R3000) LED508 6-500-510-01 LED CL-195PG-CD-T (8) (RW300)

Q502 8-729-038-67 TRANSISTOR KRC102S

< RESISTOR >

R501 1-216-819-11 METAL CHIP 680 5% 1/10W R502 1-216-819-11 METAL CHIP 680 5% 1/10W R503 1-216-819-11 METAL CHIP 680 5% 1/10W R504 1-216-821-11 METAL CHIP 1K 5% 1/10W R505 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

Page 48

CDX-R3000/RW300

DISPLAY

Ref. No. Part No. Description Remark

R506 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R507 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R508 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R509 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R510 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R511 1-216-819-11 METAL CHIP 680 5% 1/10W R512 1-216-819-11 METAL CHIP 680 5% 1/10W R513 1-216-819-11 METAL CHIP 680 5% 1/10W R514 1-216-821-11 METAL CHIP 1K 5% 1/10W R515 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R516 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R517 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R518 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R519 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R531 1-216-813-11 METAL CHIP 220 5% 1/10W

R532 1-216-813-11 METAL CHIP 220 5% 1/10W R533 1-216-813-11 METAL CHIP 220 5% 1/10W R535 1-216-815-11 METAL CHIP 330 5% 1/10W R536 1-216-809-11 METAL CHIP 100 5% 1/10W R537 1-216-809-11 METAL CHIP 100 5% 1/10W

R561 1-216-857-11 METAL CHIP 1M 5% 1/10W R571 1-216-805-11 METAL CHIP 47 5% 1/10W

(RW300)

R571 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R572 1-216-805-11 METAL CHIP 47 5% 1/10W

(RW300)

R572 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

Ref. No. Part No. Description Remark

R578 1-216-805-11 METAL CHIP 47 5% 1/10W

(RW300)

R578 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R579 1-216-805-11 METAL CHIP 47 5% 1/10W

(RW300)

R579 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

R580 1-216-805-11 METAL CHIP 47 5% 1/10W

(RW300)

R580 1-216-809-11 METAL CHIP 100 5% 1/10W

(R3000)

< SWITCH >

S501 1-786-763-11 SWITCH, TACTILE (OPEN/EJECT) S502 1-786-763-11 SWITCH, TACTILE (OPEN/EJECT) S503 1-786-763-11 SWITCH, TACTILE (OFF) S504 1-786-763-11 SWITCH, TACTILE (SOURCE) S505 1-786-763-11 SWITCH, TACTILE (MODE)

S506 1-786-763-11 SWITCH, TACTILE (SEL) S507 1-786-763-11 SWITCH, TACTILE (VOLUME +) S508 1-786-763-11 SWITCH, TACTILE (VOLUME –) S509 1-786-763-11 SWITCH, TACTILE (ATT) S510 1-786-763-11 SWITCH, TACTILE (BTM/SENS)

S511 1-786-763-11 SWITCH, TACTILE (1) S512 1-786-763-11 SWITCH, TACTILE (2) S513 1-786-763-11 SWITCH, TACTILE (SEEK + > M) S514 1-786-763-11 SWITCH, TACTILE (SEEK – m .) S515 1-786-763-11 SWITCH, TACTILE (EQ3)

S516 1-786-763-11 SWITCH, TACTILE (DSPL) S517 1-786-763-11 SWITCH, TACTILE (SHUF) S518 1-786-763-11 SWITCH, TACTILE (6) S519 1-786-763-11 SWITCH, TACTILE (5) S520 1-786-763-11 SWITCH, TACTILE (4)

S521 1-786-763-11 SWITCH, TACTILE (3) S522 1-529-566-61 SWITCH, PUSH (1 KEY) (SHUTTER) S523 1-786-763-11 SWITCH, TACTILE (REP)

R573 1-216-805-11 METAL CHIP 47 5% 1/10W

R573 1-216-809-11 METAL CHIP 100 5% 1/10W

R574 1-216-805-11 METAL CHIP 47 5% 1/10W

R574 1-216-809-11 METAL CHIP 100 5% 1/10W

R575 1-216-805-11 METAL CHIP 47 5% 1/10W

R575 1-216-809-11 METAL CHIP 100 5% 1/10W

R576 1-216-805-11 METAL CHIP 47 5% 1/10W

R576 1-216-809-11 METAL CHIP 100 5% 1/10W

R577 1-216-805-11 METAL CHIP 47 5% 1/10W

R577 1-216-809-11 METAL CHIP 100 5% 1/10W

(RW300)

(R3000)

(RW300)

(R3000)

(RW300)

(R3000)

(RW300)

(R3000)

(RW300)

(R3000)

Page 49

MEMO

CDX-R3000/RW300

Page 50

CDX-R3000/RW300

REVISION HISTOR Y

Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next re vised page.

Ver. Date Description of Revision

1.0 2003.11 New

1.1 2005.07 Change of display board. (Suffix -11 to -13) (SPM-05009)

1.2 2006.05 Correction of RF level. (SPM-06010)

Sony CDXR-3000, CDXRW-300 Service manual

TABLE OF CONTENTS

GENERAL

DISASSEMBLY

CD mechanism block

sub panel (1) assy

MAIN board

chassis (T) sub assy

roller arm assy

chassis (OP) assy

optical pick-up

SL motor assy (M902)

SERVO board

DIAGRAMS

EXPLODED VIEWS

ELECTRICAL PARTS LIST

DISPLAY

DISPLAY MAIN

MAIN SENSOR SERVO

SUPPLEMENT-1

DISCRIMINATION

DISPLAY

REVISION HISTOR Y