Sony CDX-4000-RV Service manual
CDX-4000RV
SERVICE MANUAL
Ver 1.2 2001. 05
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
Model Name Using Similar Mechanism CDX-3900R/4000R/4000RX
CD Drive Mechanism Type MG-383Z-121//Q
Optical Pick-up Name KSS-720A
AEP Model
UK Model
CD player section
Signal-to-noise ratio 90 dB
Frequency response 10 – 20,000 Hz
Wow and flutter Below measurable limit
Tuner section
FM
Tuning range 87.5 – 108.0 MHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 8 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation 35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
MW/LW
Tuning range MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW: 30 µV
LW : 40 µV
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 50 W × 4 (at 4 ohms)
General
Outputs Audio outputs
Power aerial relay control
lead
Power amplifier control
lead
Telephone ATT control
lead
Tone controls Bass ±9 dB at 100 Hz
Treble ±9 dB at 10 kHz
Power requirements 12 V DC car battery
(negative ground)
Dimensions Approx. 178 × 50 × 183 mm
(w/h/d)
Mounting dimension Approx. 182 × 53 × 162 mm
(w/h/d)
Mass Approx. 1.2 kg
Supplied accessories Parts for installation and
connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
9-870-125-12
2001E0400-1
© 2001. 5
FM/MW/LW COMPACT DISC PLAYER
Sony Corporation
e Vehicle Company
Shinagawa Tec Service Manual Production Group
1
Ver 1.1 2000. 08
SERVICE NOTES
This product is classified as a CLASS 1 LASER PRODUCT.
This label is located on the bottom of the
chassis.
This label is located on the drive unit's internal
chassis.
When replacing the chassis (T) of mechanism deck which have
the “CAUTION LABEL” attached, please be sure to put a new
CAUTION LABEL (3-223-913-11) to the chassis (T).
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
TABLE OF CONTENTS
1. GENERAL
Location of controls................................................................. 3
Getting Started......................................................................... 3
Setting the clock ...................................................................... 3
CD Player ................................................................................ 3
Radio ....................................................................................... 4
RDS ......................................................................................... 4
Other Functions ....................................................................... 6
Additional Information............................................................ 7
Connections ............................................................................. 8
2. DISASSEMBLY
2-1. Sub Panel Assy.................................................................. 10
2-2. CD Mechanism Block ....................................................... 10
2-3. Main Board ....................................................................... 11
2-4. Heat Sink ........................................................................... 11
2-5. Chassis (T) Assy................................................................12
2-6. Lever Assy......................................................................... 12
2-7. Servo Board....................................................................... 13
2-8. ARM Roller Assy .............................................................. 13
2-9. Chassis (OP) Assy............................................................. 14
2-10. Optical Pick-up Block ....................................................... 14
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 15
3-2. Block Diagram –CD Section–........................................... 21
3-3. Block Diagram –Tuner Section–....................................... 22
3-4. Block Diagram –Display Section–.................................... 23
3-5. Circuit Boards Location .................................................... 23
3-6. Printed Wiring Boards –CD Mechanism Section–............24
3-7. Schematic Diagram –CD Mechanism Section (1/2)– ....... 26
3-8. Schematic Diagram –CD Mechanism Section (2/2)– ....... 27
3-9. Printed Wiring Board –Main Section–.............................. 28
3-10. Schematic Diagram –Main Section (1/3)– ........................ 30
3-11. Schematic Diagram –Main Section (2/3)– ........................ 31
3-12. Schematic Diagram –Main Section (3/3)– ........................ 32
3-13. Schematic Diagram –Sub (CD) Section–.......................... 33
3-14. Printed Wiring Board –Sub (CD) Section–....................... 34
3-15. Printed Wiring Board –Key Section–................................ 35
3-16. Schematic Diagram –Key Section–................................... 36
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
4. EXPLODED VIEWS
4-1. Chassis Section ................................................................. 40
4-2. Front Panel Section ...........................................................41
4-3. CD Mechanism Section (1) ............................................... 42
4-4. CD Mechanism Section (2) ............................................... 43
4-5. CD Mechanism Section (3) ............................................... 44
5. ELECTRICAL PARTS LIST ........................................ 45
SECTION 1
GENERAL
This section is extracted
from instruction manual.
3
45678910
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY
4 two claws
6 sub panel assy
2 PTT 2.6x8
2-2. CD MECHANISM BLOCK
5 CD mechanism block
2 PTT 2.6x6
3 claw
5 CN500
1 PTT 2.6x8
7 bracket (CD)
6 PTT 2.6x5
3
1 PTT 2.6x5
4 CN301
8
8
2-3. MAIN BOARD
6 MAIN board
5 ground point screws
(PTT 2.6x6)
4 ground point screws
(PTT 2.6x6)
3 PTT 2.6x
2 PTT 2.6x8
1 PTT 2.6x8
2-4. HEAT SINK
5 heat sink
4 PTT 2.6x
3 PTT 2.6x12
1 PTT 2.6x8
2 PTT 2.6x8
11
2-5. CHASSIS (T) ASSY
2 P 2x3
3 P 2x3
2-6. LEVER ASSY
1 Unsolder the
lead wires.
4 chassis (T) assy
black
red
white
4 claws
5 guide (disc)
6 lever (R) assy
3 tension spring (LR)
7 lever (L) assy
1 PS 2x4
2 DISC IN SW board
12
2-7. SERVO BOARD
7 PS 2x4
8 PS 2x4
3 Removal the solders.
1 CN3
5 P 2x3
6 loading motor assy
2 CN2
9 SERVO board
4 Removal the solders.
2-8. ARM ROLLER ASSY
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
2 arm roller assy
3 PS 2x3
4 LOAD SW board
shaft retainer
washer (RA)
arm
washer
Fig. 1
washer
arm
shaft retainer
washer (RA)
1 tension spring (RA)
13
2-9. CHASSIS (OP) ASSY
8 compression spring (FL)
1 tension spring (KF1)
7 chassis (OP) assy
9 compression spring (FL)
2 tension spring (KR1)
5 Fit lever (D) in the
direction of the arrow.
6 Turn loading ring in the
direction of the arrow.
4 damper (T)
2-10. OPTICAL PICK-UP BLOCK
1 P 2x3
2 sled motor assy
3 damper (T)
3 optical pick-up block
14
SECTION 3
DIAGRAMS
3-1. IC PIN DESCRIPTIONS
• IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No. Pin Name I/O Pin Description
1 DVDD — Digital power supply pin
2 DVSS — Digital ground
3 SOUT O Servo brock serial data output (Not used.)
4 SOCK O Servo brock serial data read clock output (Not used.)
5 XOLT O Servo brock serial data latch output (Not used.)
6 SQSO O Sub Q 80 bit, PCM peak and level data output. CD TEXT data output
7 SQCK I Clock input from SQSO read output.
8 SCSY I Fixed at “L”.
9 SBSO O Serial output of sub-P to W. (Not used.)
10 EXCK I Clock input from SBSO read output. (Fixed at “L”)
11 XRST I System reset (“L”: Reset)
12 STSM I System mute input (Fixed at “L”)
13 DATA I Serial data input from CPU.
14 XLAT I Latch input from CPU. Latch serial data at the falling edge.
15 CLOK I Serial data transfer clock input from CPU.
16 SENS O SENS output for CPU.
17 SCLK I Clock input from SENS serial data read.
18 ATSK I/O Input/output for anti-shock.
19 WFCK O WFCK (Write Flame Clock) output (Not used.)
20 XUGF O XUGF output (Not used.)
21 XPCK O XPCK output (Not used.)
22 GFS O GFS output
23 C2PO O C2PO output (Not used.)
24 SCOR O “H” output at either detection, sub code sync S0 or S1.
25 C4M O 4.2336 MHz output (Not used.)
26 WDCK O Word clock input f=2Fs (Not used.)
27 COUT I/O Track number count signal input/output (Not used.)
28 MIRR I/O Mirror signal input/output (Not used.)
29 DVSS — Digital ground
30 DVDD — Digital power supply pin
31 DFCT I/O Diffect signal input/output (Not used.)
32 FOK I/O Focus OK signal output
33 PWM1 I External control input of spindle motor.
34 LOCK I/O Lock signal input/output
35 MDP O Servo control output of spindle motor.
36 SSTP I Disc most inner track detection signal input
37 FSTIO I/O 2/3 frequency division output of pins ih and ij. (Not used.)
38 SFDR O Sled drive output
39 SRDR O Sled drive output
40 TFDR O Tracking drive output
41 TRDR O Tracking drive output
42 FFDR O Focus drive output
43 FRDR O Focus drive output
44 DVDD — Digital power supply pin
45 DVSS — Digital ground
46 TEST I Test pin (Fixed at “L”)
47 TES1 I Test pin (Fixed at “L”)
48 XTSL I X’tal select input (“L”: 16.9344 MHz, “H”: 33.8688 MHz)
49 VC I Center voltage input
50 FE I Focus error signal input
51 SE I Sled error signal input
15
Pin No. Pin Name I/O Pin Description
52 TE I Tracking error signal input
53 CE I Center servo analog input
54 RFDC I RF signal input
55 ADIO O Test pin (Not used.)
56 AVSSO — Analog ground
57 IGEN I Constant current input from OP amplifier.
58 AVDDO — Analog ground
59 ASYO O EFM full-swing output (“L”: VSS, “H”: VDD)
60 ASYI I Asymmetry comparate voltage input
61 RFAC I EFM signal input
62 AVSS3 — Analog ground
63 CLTV I VCO control voltage input from master.
64 FILO O Filter output for master PLL (slave=digital PLL)
65 FILI I Filter input from master PLL.
66 PCO O Charge pump output for master PLL.
67 AVDD3 — Analog power supply pin
68 BIAS I Asymmetry circuit constant current input
69 VCTL I VCO2 control input from wideband EFM PLL. (Not used.)
70 V16M O VCO2 oscillator output for wideband EFM PLL. (Not used.)
71 VPCO O Charge pump output for wideband EFM PLL. (Not used.)
72 DVSS — Digital ground
73 MD2 I Digital out ON/OFF control input (“L”: OFF, “H”: ON)
74 DOUT O Digital out output
75 ASYE I Asymmetry circuit ON/OFF input (“L”: OFF, “H”: ON)
76 DVDD — Digital power supply pin
77 LRCK O D/A interface LR clock output (f=Fs)
78 LRCKI I D/A interface LR clock input
79 PCMD O D/A interface serial data output (2’s COMP, MSB fast)
80 PCMD I D/A interface serial data input (2’s COMP, MSB fast)
81 BCK O D/A interface bit clock output
82 BCKI I D/A interface bit clock input
83 EMPH O Emphasis ON/OFF signal output
84 EMPHI I Emphasis ON/OFF signal input (“H”: ON, “L”: OFF)
85 XVDD — Power supply for master clock.
86 XTAI I X’tal oscillator input from master clock (16.9344 MHz).
87 XTAO O X’tal oscillator output for master clock (16.9344 MHz).
88 XVSS — Ground pin for master clock.
89 AVDD1 — Analog power supply pin
90 AOUT1 O Lch analog output
91 AIN1 I Lch OPAMP input
92 LOUT1 O Lch LINE output
93 AVSS1 — Analog ground
94 AVSS2 — Analog ground
95 LOUT2 O Rch LINE output
96 AIN2 I Rch OPAMP input
97 AOUT2 O Rch analog output
98 AVDD2 — Analog power supply pin
99 RMUT O Rch “0” detect Flug (Not used.)
100 LMUT O Lch “0” detect Flug (Not used.)
16
• IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD)
Pin No. Pin Name I/O Pin Description
1 ITRPT — Not used in this set.
2, 3 ——Not used in this set.
4, 5 NCO — Not used in this set.
6 OPEN I Front panel open detection input
7 CLOSE O Front panel close control output
8 LINKOFF I Bus interface link input
9 NCO — Not used in this set.
10 D SW I Down switch input (SW4)
11 SSTP I Limit switch input (SW3)
12, 13 NCO — Not used in this set.
14, 15 ——Not used in this set.
16 EMPH O O De-emphasis ON/OFF control output
17 CDMON O CD mechanism deck power control output
18 CD ON O CD power control output
19 A MUT O System attenuate control output
20 LD ON O Laser power ON/OFF control output
21 CD RST O CD system reset output
22 HOLD O Hold switch output
23 AGC CONT O AGC control output
24 ——Not used in this set.
25 PH3 I Not used in this set.
26 TSTIN0 I Not used in this set.
27 TSTIN1 I Not used in this set.
28 TST.CLV I Not used in this set.
29 NCO — Not used in this set.
30 RESET I System reset input (“L”=Reset)
31 X IN I X’tal oscillator input from system clock. (10 MHz)
32 X OUT O X’tal oscillator output for system clock. (10 MHz)
33 GND — Analog ground
34 XT OUT O Not used in this set.
35 XT IN I Not used in this set.
36 AVSS — A/D converter ground
37 AVREF I A/D converter reference voltage input
38 TEP L I Not used in this set.
39 TEP H I Not used in this set.
40 SLED– I Sled drive input
41 PH2 I Not used in this set.
42 SEK/SMET I Fixed at “H” in this set.
43 GFS/MNT2 SEL I Fixed at “H” in this set.
44 SC-JIG ON/OFF I Fixed at “H” in this set.
45 SCLK O CD-TEXT data read clock output
46 LOCK I/O Lock signal input/output
47 ——Not used in this set.
48 SCK2 O Sub Q read clock output
49 SI2 I Sub Q 80 bit, PCM peak and level data 16 bit input.
50 ——Not used in this set.
51 BUS CLK I/O Bus system serial clock input/output
52 BUS SI I Bus system serial interface input
53 BUS SO O Bus system serial interface output
54 F OK I Focus OK signal input
55 GFS I GFS signal detection input
56 TEST MODE I Fixed at “H” in this set.
17
Pin No. Pin Name I/O Pin Description
57 SENS I SENS signal input
58 ——Not used in this set.
59 ——Not used in this set.
60 BU.IN I Back-up power detection input
61 BUSON I Bus on control input
62 IN SW I Disc in switch input (SW1)
63 SELF SW I Self switch input (SW2)
64 SCOR O Sub-code sync output
65 CD-CKO O CD signal process serial clock input
66 LM LOD O Loading motor control output
67 CD DATA O CD signal process serial data output
68 CD-XLAT O CD signal process serial data latch output
69 LM-EJ O Loading motor control output
70 DRV-OE O Focus/tracking coil/sled motor control output
71 MD2 O Digital out ON/OFF control output (“L”: OFF, “H”: ON)
72 VDD — Power supply pin
73 NIH I Fixed at “H” in this set.
74 V/Z I Fixed at “H” in this set.
75 PH1 I Not used in this set.
76 ——Not used in this set.
77 DOUT-SEL I Fixed at “H” in this set.
78 – 80 ——Not used in this set.
18
• IC501 MB90574BPMT-G-266-BND (SYSTEM CONTROL) (MAIN BOARD)
Pin No. Pin Name I/O Pin Description
1 TUNON O Tuner power control output (+5 V)
2 ——Not used. (Open)
3 BUSON O SONY-BUS ON control output
4 – 6 ——Not used. (Open)
7 ILLON O Illumination power control output
8 VCC — Power supply pin (+5 V)
9 E2P SIO I/O E2P SONY-BUS serial data input/output
10 E2P CKO I/O E2P SONY-BUS serial clock input/output
11 SYSRST O SONY-BUS system reset output
12 DOORSW (WRITE OUT) I DOOR OPEN/CLOSE detection input (“L”: CLOSE, “H”: OPEN)
13 LCDSO (WRITE IN) O LCD serial data output
14 LCDCKO O LCD serial clock output
15 LCDCE O LCD chip enable output
16 BEEP O BEEP output
17 UNISI I SONY-BUS serial data input
18 UNISO O SONY-BUS serial data output
19 UNICKO O SONY-BUS serial clock output
20 UNICKI I SONY-BUS serial clock input
21 CD MD I CD/MD select input (“L”: CD, “H”: MD) (Fixed at “L” in this set)
22 FLASHW I Flash memory write mode detection input
23 ——Not used. (Open)
24 SIRCS I Remote commander (infrared ray reception) input
25 – 28 ——Not used. (Open)
29 DOORIND O DOOR indicator output
30 IFWIDTH O Not used in this set.
31 ——Not used. (Open)
32 NS MASK O Noise mask output
33 VSS — Ground
34 C — Condenser connection pin of power stabilization.
35 AD ON O Power control output for A/D converter.
36, 37 REIN0, 1 I Rotary encoder 0, 1 input
38 DVCC — D/A converter Vref pin (+5 V)
39 DVSS — D/A converter ground pin
40, 41 ——Not used. (Open)
42 AVCC — Analog power supply pin (+5 V)
43 AVRH — A/D converter Vref+ pin (+5 V)
44 AVRL — A/D converter Vref– pin
45 AVSS — Analog ground
46, 47 KEYIN0, 1 I Key 0, 1 input
48 RCIN0 I Rotary commander key input
49 DSTSEL I Destination setting input (Fixed at “L” in this set)
50 QUALITY I Noise detection input
51 FMAGC I FM AGC detection input
52 MPTH I Multi path detection input
53 VSM I Signal meter detection input
54 VCC — Power supply pin (+5 V)
55 RAMBU I RAM reset detection input
56 TUNATT O TUNER mute control output
57 VOLATT O Electric volume mute output
58 ATT O LINE mute output
59 AMPON O Power amplifier standby control output
60 AMPATT O Power amplifier mute control output
19
Pin No. Pin Name I/O Pin Description
61 COLSW I
62 COLSEL I Illumination color select input (“L”: AMBER, “H”: GREEN) (Fixed at “L” in this set)
63 VSS — Ground
64 DAVN I Block synchronization detection input of RDS data.
65 FILE I Custom file setting input
66 TEXT I CD text setting input
67 NOSESW I Front panel attachment detection input
68, 69 ——Not used. (Open)
70 I2C SIO I/O I2C BUS serial data input/output
71 I2C CKO I/O I2C BUS serial clock input/output
72 ——Not used. (Open)
73 X1A — Low speed oscillation connecting pin (32.768 kHz)
74 X0A — Low speed oscillation connecting pin (32.768 kHz)
75 ——Not used. (Open)
76 KEYACK I Key acknowledge input
77 BUIN I Backup voltage detection input
78 ILLIN I Illumination (ILLIN) detection input (Fixed at “L” in this set)
79 TELATT I Telephone (TEL) detection input
80 ——Not used. (Open)
81 TEST IN I Test mode setting input
82 ACC IN I Accessory power supply (ACC) detection input
83 ——Not used. (Open)
84 LOCKIN I MD LOCK detection input
85 RCIN1 I Rotary commander SHIFT input
86 HSTX I Hardware standby setting input
87 MD2 I Connect to VSS in this set.
88, 89 MD1, 0 I Connect to VCC in this set.
90 RSTX I Reset input
91 VSS — Ground
92 X0 — High speed oscillation connecting pin (3.68 MHz)
93 X1 — High speed oscillation connecting pin (3.68 MHz)
94 VCC — Power supply pin (+5 V)
95 – 97 ——Not used. (Open)
98 DIM SEL I
99 TAP CD I TAPE/CD select input (“L”: CD, “H”: TAPE) (Fixed at “L” in this set)
100 – 118 ——Not used. (Open)
119 VSS — Ground
120 PW ON O System power control output
Illumination color switch input (“L”: 2 colors, “H”: 1 color)
(Fixed at “H” in CDX-4000RV)
Dimmer select input (“L”: With dimmer select, “H”: Without dimmer select)
(Fixed at “L” in this set)
20
3-2. BLOCK DIAGRAM — CD SECTION —
CDX-4000RV
OPTICAL PICKUP
KSS-720A
A
C
B
D
E
F
PD
LD
FOCUS
COIL
TRACKING
COIL
I-V
CONV.
M902
SLED
MOTOR
M901
SPINDLE
MOTOR
A
5
C
7
B
6
D
8
FOCUS
ERROR
E
11
TRACKING
F
ERROR
10
PD
4
LD
LD
DRIVE
Q101
TRACKING/FOCUS COIL DRIVE
SLED/SPINDLE/LOADING MOTOR DRIVE
10
11
12
13
AMP
LD
3
IC7
FOCUS
COIL
DRIVE
TRACKING
8
COIL
DRIVE
9
SLED
6
MOTOR
7
DRIVE
SPINDLE
MOTOR
DRIVE
RF AMP, LD APC,
ERROR AMP
IC1
22
21
25
24
31
32
18
RFO RFAC
RF
EQ
FE
TE
LD ON
HOLD SW
AGC CONT
16
14
13
22
21
20
DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC501
LOUT1
LOUT2
LOCK
SQSO
SQCK
SCOR
XRST
DATA
XLAT
SCLK
CLOK
SENS
XTALI
XTALO
MD2
GFS
FOK
92
95
34
6
7
24
73
11
13
14
17
15
16
22
32
86
87
SW4
(LIMIT)
SW1
(DISC IN)
SW3
(LOAD IN)
SW2
(SELF)
RFDC
FE
TE
SE
FFDR
FRDR
TFDR
TRDR
SFDR
SRDR
MDP
EFM
DEM
SERVO
CTL
61
54
50
52
51
42
43
40
41
38
39
35
D/A
I/F
DIGITAL
CLV
D/A
CONV.
SUB
CODE
PROCESS
X2
16MHz
CD L
R-CH
TUNER
A
SECTION
CD SYSTEM CONTROL
LOCK
46
SI2
49
SCK2
48
SCOR
64
MD2
71
CD RST
21
CD DATA
67
CD XLAT
68
SCLK
45
CD CKO
65
SENS
57
GFS
55
FOK
54
SSTP
11
D SW
10
IN SW
64
SELF SW
63
(Page 22)
IC5
A MUT
OPEN
BUS CLK
BUS SI
BUS SO
BUS ON
RESET
BU IN
X IN
X OUT
19
51
52
53
61
30
60
31
32
6
(KEY BOARD)
X1
10MHz
ATT
SW503
(RESET)
TUNER
B
SECTION
(Page 22)
SYSTEM CONTROL
IC501 (1/3)
ATT
58
DOOR SW
12
UNI CKI
20
UNI CKO
19
UNI SO
18
UNI SI
17
BUS ON
3
SYS RST
11
BU IN
77
RSTX
90
HSTX
86
IC652
1 3
RESET
BATT (H)
CHECK
Q701
BATT (L)
CHECK
Q702,703
BU 5V
BATT
BATT
M903
LOADING
MOTOR
04
LOADING
5
MOTOR
4
DRIVE
MUTE 1
MUTE 2
1
2
34
35
POWER
CONT
CD 5V
CD 6V
5V REG
Q364
Q365
6V REG
Q362
11V REG
Q361
POWER
CONT
Q363
BATT
69
66
40
70
20
22
23
18
17
LM EJ
LM LOD
SLED –
DRIVE ON
LD ON
HOLD
AGC CONT
CD ON
CDM ON
• Signal path
:CD
21 21
CDX-4000RV
3-3. BLOCK DIAGRAM — TUNER SECTION —
CNJ151
AUDIO OUT REAR
–1L–2
R
J1
(ANTENNA)
04
TUNER UNIT
TU1
ANTFM MPX
2 10
AM DET
ANTAM
1
IF AM
S-METER
I2C SDA
I2C SCL
RDS DET
FM AGC
E2PROM SDA
E2PROM SCL
ELECTRONIC VOLUME
IC151
Q171
MUTE
ATT
BATT
R-CH
B
CD
SECTION
(Page 21)
ACC
CHECK
Q661
POWER SUPPLY
7 6
VCC AMP +B
2
8.7V ON
3
5.6V ON
4
STB
IC671
COM 8V
TU 5.6V
TU 8.7V
A
CD
X51
CDL
Q121
MUTE
RDS DECODER
IC51
8
Q111
MUTE
IC90
NOISE
DET
NOISE ON
9
MULTI
PATH
RDS/RDBS
DEM/DEC
4 5
SECTION
Q90
10
DET
MUTE
CONT
Q131
4.332MHz
(Page 21)
8
19
BUFFER
Q1
5 1
14
12
13
SDA SCA
LV IN
20 2
9
4
17
18
MPX
16
OSCO OSCI
SEL
1
MPX
13
AM
11
AM IF
12
LEVEL
14
MPIN
15
SDA
20
SCL
21
SM
18
SYSTEM CONTROL
VOL ATT
57
TUN ATT
56
QUALITY
50
NS MASK
32
VSM
53
I2C SIO
70
I2C CKO
71
MPTH
52
DAVN
64
FM AGC
51
E2P SIO
9
E2P CKO
10
IC501 (2/3)
AMP MUTE
OUT LF
OUT LR
BEEP
AMP ON
TEL ATT
ACC IN
TEST IN
TU ON
PW ON
30
29
16
59
60
79
82
81
120
Q181
MUTE
MUTE
CONT
Q621, 622
1
POWER AMP
IC611
12
11
AUX IN
16
STAND BY
4
MUTE
22
TEL
ATT
Q571
8
ANT +B
5
BU +B BU 5V
9
10
11
COM 8V
TU 5.6V
TU 8.7V
5
3
9
8
R-CH
BATT
F901
• Signal path
:FM
:MW
:CD
CN601
1
FL+
9
FL–
2
RL+
10
RL–
4
FR+
12
FR–
3
RR+
11
RR–
16
BATT
13
ATT
7
ACC
15
TEST
5
AMP R
6
ANT R
2222
t
CDX-4000RV
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL
04
KEY MATRIX
LSW901-917
S901-904
LSW801
J501
(REMOTE IN)
ACTIVE
ACTIVE
ROTARY
ENCODER
RE901
SW504
(NOSE DET)
KEY
Q651
KEY
Q652
KEY ACT
X502
32.768kHz
KEY IN0 DATA
46 13
KEY IN1
KEY ACK
76
AD ON
35
RC IN1
85
RC IN0
48
RE IN0
36
RE IN1
37
NOSE SW
67
XOA
73
XIA
74
IC501 (3/3)
DOOR IND
LCD SO
LCD CKO
LCD CE
ILL ON
3-5. CIRCUIT BOARDS LOCATION
LCD DRIVE
IC901
64
14
1547
CL
63
CE
62
LCD901
DISC IN SW board
SUB (CD) board
DIMMER
3
LED DRIVE
DOOR IND
DRIVE
29
XO
92
XI
93
Q551
LED801-803 LED910-915 LSW901-907,909-917
POWER
CONT
7
Q633
X501
3.68MHz
+10V REG
Q631
BATT
Q903
LED901-904
ILL +B
LOAD SW board
KEY board
SUB board
LIMIT SW board
tuner uni
(TU1)
MAIN board
SERVO board
23 23
Loading...