Sony BVM-X300 Operating Instructions 1.1 r2

Professional

4-566-075-14(2)

Video Monitor

Operating Instructions

Before operating the unit, please read this manual thoroughly
and retain it for future reference.

BVM-X300

Software Version 1.1

© 2015 Sony Corporation

Owner’s Record

The model and serial numbers are located at the rear.
Record these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your
Sony dealer regarding this product.

Model No.
Serial No.

Important Safety Instructions

 Read these instructions.
 Keep these instructions.
 Heed all warnings.
 Follow all instructions.
 Do not use this apparatus near water.
 Clean only with dry cloth.
 Do not block any ventilation openings.

Install in accordance with the manufacturer’s
instructions.

 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.

 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.

 Only use attachments/accessories specified by the

manufacturer.

 Use only with the cart, stand, tripod,

bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

 Unplug this apparatus during lightning storms or

when unused for long periods of time.

 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.

WARNING

To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.

THIS APPARATUS MUST BE EARTHED.

WAR NIN G

When installing the unit, incorporate a readily accessible
disconnect device in the fixed wiring, or connect the
power plug to an easily accessible socket-outlet near the
unit. If a fault should occur during operation of the unit,
operate the disconnect device to switch the power supply
off, or disconnect the power plug.

This symbol is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.

This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the
appliance.

CAUTION

The apparatus shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases,
shall be placed on the apparatus.

CAUTION

The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even
if the unit itself has been turned off.

WAR NIN G

Excessive sound pressure from earphones and
headphones can cause hearing loss.
In order to use this product safely, avoid prolonged
listening at excessive sound pressure levels.

When installing the installation space must be secured
in consideration of the ventilation and service operation.

 Do not block the ventilation slots, and vents of the

fans.

 Leave a space around the unit for ventilation.
 Leave more than 40 cm of space in the rear of the unit

to secure the operation area.

2

When the unit is installed on the desk or the like, leave at
least 10 cm of space in the top side. Leaving 40 cm or
more of space in the rear of the unit is recommended for
service operation.

WARNING: THIS WARNING IS APPLICABLE FOR
USA ONLY.
If use d in USA, us e th e UL LIS TED power c ord sp ecified
below.
DO NOT USE ANY OTHER POWER CORD.

All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of part 15 of FCC Rules.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.

Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SJT or SVT, three 16 or 18 AWG wires
Length Minimum 1.5 m (4 ft 11 in), Less than 2.5 m
(8 ft 3 in)
Rating Minimum 10A, 125V

Using this unit at a voltage other than 120V may require
the use of a different line cord or attachment plug, or
both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.

WARNING: THIS WARNING IS APPLICABLE FOR
OTHER COUNTRIES.

1. Use the approved Power Cord (3-core mains lead) /
Appliance Connector / Plug with earthing-contacts
that conforms to the safety regulations of each
country if applicable.

2. Use the Power Cord (3-core mains lead) / Appliance
Connector / Plug conforming to the proper ratings
(Voltage, Ampere).

If you have questions on the use of the above Power Cord
/ Appliance Connector / Plug, please consult a qualified
service personnel.

For the customers in the U.S.A.

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

For the customers in Canada

CAN ICES-3 (A)/NMB-3(A)

For the customers in Europe

This product with the CE marking complies with the
EMC Directive issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:

 EN55103-1 : Electromagnetic Interference(Emission)
 EN55103-2 : Electromagnetic

Susceptibility(Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).

For the customers in Europe

This product has been manufactured by or on behalf of
Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108­0075 Japan. Inquiries related to product compliance
based on European Union legislation shall be addressed
to the authorized representative, Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters, please
refer to the addresses provided in the separate service or
guarantee documents.

This apparatus shall not be used in the residential area.

For the customers in Europe, Australia and New
Zealand
WAR NIN G

This is a Class A product. In a domestic environment,
this product may cause radio interference in which case
the user may be required to take adequate measures.

Disposal of Old Electrical & Electronic Equipment
(Applicable in Republic of India)

You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.

This symbol indicates that this product shall not be
treated as household waste and may not be dropped in

3

garbage bins. Product owners are advised to deposit
their product at the nearest collection point for the
recycling of electrical and electronic equipment.
Your co-operation shall facilitate proper disposal & help
prevent potential negative consequences/hazards to the
environment and human health, which could otherwise
be caused by inappropriate waste disposal including

improper handling, accidental breakage, damage and/
or improper recycling of e-waste. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of this
product, please contact your local civic office, your
household waste disposal service provider or the store
where you made the purchase. You may contact our
company’s toll free number in India for assistance.

This product complies with the “India E-waste Rule
2011”. The E-waste Rules, 2011 is an Indian directive
aimed at reducing the harmful environmental impact of
waste electrical equipment by restricting the use of
known hazardous substances. As of 1st May 2012, new
electrical and electronic equipment introduced into the
market may no longer contain the following chemicals
or its specified maximum concentration levels:
Lead, Mercury, Hexavalent Chromium, Polybrominated
Biphenyls (PBB) or Polybrominated Diphenylethers
(PBDE) - in concentrations exceeding 0.1 weight % and
Cadmium - 0.01 weight %, except of exemptions set in
Schedule 2 of the aforesaid Rule.

For the customers in the U.S.A.
SONY LIMITED WARRANTY

- Please visit http://
www.sony.com/psa/warranty for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.

For the customers in Canada
SONY LIMITED WARRANTY

- Please visit http://
www.sonybiz.ca/pro/lang/en/ca/article/resources­warranty-product-registration for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.

For the customers in Europe

Sony Professional Solutions Europe - Standard
Warranty and Exceptions on Standard Warranty.
Please visit http://www.pro.sony.eu/warranty

for
important information and complete terms and
conditions.

For the customers in Korea
SONY LIMITED WARRANTY

- Please visit http://
bpeng.sony.co.kr/handler/BPAS-Start for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.

Consignes de sécurité importantes

 Lisez ces instructions.
 Conservez ces instructions.
 Tenez compte de tous les avertissements.
 Suivez toutes les instructions.
 N’utilisez pas cet appareil à proximité d’eau.
 Nettoyez cet appareil uniquement avec un chiffon sec.
 Ne bloquez aucun orifice de ventilation.

Installez cet appareil conformément aux instructions
du fabricant.

 Ne l’installez pas à proximité de sources de chaleur

comme des radiateurs, des registres de chaleur, des
poêles ou d’autres appareils (y compris des
amplificateurs) produisant de la chaleur.

 Ne désactivez pas le dispositif de sécurité de la fiche

polarisée ou avec mise à la terre. Une fiche polarisée
possède deux lames dont l’une est plus large que
l’autre. Une fiche avec mise à la terre possède deux
lames et une troisième broche de mise à la terre. La
lame la plus large et la troisième broche sont fournies
pour votre sécurité. Si la fiche fournie ne rentre pas
dans votre prise de courant, consultez un électricien
afin qu’il remplace la prise obsolète.

 Protégez le cordon d’alimentation afin que personne

ne marche dessus et qu’il ne se coince pas, en
particulier au niveau de la fiche, de la prise de courant
et à l’endroit où il sort de l’appareil.

 N’utilisez que les fixations et accessoires indiqués par

le fabricant.

 Utilisez l’appareil uniquement avec le

chariot, le support, le trépied ou la table
indiqué par le fabricant ou vendu avec
l’appareil. Lorsque vous utilisez un chariot,
faites attention lorsque vous déplacez le chariot et
l’appareil ensemble afin d’éviter de vous blesser en cas
de chute.

 Débranchez cet appareil en cas d’orage ou lorsqu’il

n’est pas utilisé pendant de longues périodes.

 Faites appel à un technicien qualifié pour toute

réparation/entretien. L’entretien/réparation est
nécessaire lorsque l’appareil a été endommagé de
quelque façon que ce soit, par exemple si le cordon ou
la fiche d’alimentation a été endommagé, si du liquide
a été renversé ou si des objets sont tombés dans
l’appareil, si l’appareil a été exposé à la pluie ou à
l’humidité, s’il ne fonctionne pas normalement ou s’il
a subi une chute.

AVERTISSEMENT

Afin de réduire les risques d’incendie ou
d’électrocution, ne pas exposer cet appareil à la
pluie ou à l’humidité.

4

Afin d’écarter tout risque d’électrocution, garder le
coffret fermé. Ne confier l’entretien de l’appareil
qu’à un personnel qualifié.

CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE.

AVERTISSEMENT

Lors de l’installation de l’appareil, incorporer un
dispositif de coupure dans le câblage fixe ou brancher la
fiche d’alimentation dans une prise murale facilement
accessible proche de l’appareil. En cas de problème lors
du fonctionnement de l’appareil, enclencher le dispositif
de coupure d’alimentation ou débrancher la fiche
d’alimentation.

Ce symbole est destiné à avertir
l’utilisateur de la présence d’une « tension
dangereuse » non isolée dans l’enveloppe
du produit, qui pourrait être
suffisamment importante pour
représenter un risque d’électrocution pour
les personnes.

Ce symbole est destiné à avertir
l’utilisateur de la présence d’instructions
d’utilisation et de maintenance (entretien/
réparation) importantes dans la
documentation accompagnant l’appareil.

En cas d’utilisation aux États-Unis, utilisez le cordon
d’alimentation RÉPERTORIÉ UL indiqué ci-dessous.
N’UTILISEZ AUCUN AUTRE CORDON
D’ALIMENTATION.

Bouchon de fiche Lame parallèle avec broche de terre
(configuration NEMA 5-15P)
Cordon Type SJT ou SVT, trois fils 16 ou 18
AWG
Longueur Minimum 1,5 m (4 pieds 11 pouces),
moins de 2,5 m (8 pieds 3 pouces)
Caractéristiques nominales Minimum 10 A, 125 V

L’utilisation de cet appareil à une tension autre que 120 V
peut nécessiter l’utilisation d’un type différent de cordon
ou de fiche de fixation, ou les deux. Afin de réduire les
risques d’incendie ou d’électrocution, faites appel à un
technicien qualifié pour toute réparation/entretien.

AVERTISSEMENT : CET AVERTISSEMENT
S’APPLIQUE AUX AUTRES PAYS.

1. Utilisez un cordon d’alimentation (câble secteur à 3
fils)/fiche femelle/fiche mâle avec des contacts de
mise à la terre conformes à la réglementation de
sécurité locale applicable.

2. Utilisez un cordon d’alimentation (câble secteur à 3
fils)/fiche femelle/fiche mâle avec des
caractéristiques nominales (tension, ampérage)
appropriées.

Pour toute question sur l’utilisation du cordon
d’alimentation/fiche femelle/fiche mâle ci-dessus,
consultez un technicien du service après-vente qualifié.

Pour les clients au Canada

CAN ICES-3 (A)/NMB-3(A)

AT T EN T IO N

Eviter d’exposer l’appareil à un égouttement ou à des
éclaboussures. Ne placer aucun objet rempli de liquide,
comme un vase, sur l’appareil.

AT T EN T IO N

Cet appareil n’est pas déconnecté de la source
d’alimentation secteur tant qu’il est raccordé à la prise
murale, même si l’appareil lui-même a été mis hors
tension.

AVERTISSEMENT

Une pression acoustique excessive en provenance des
écouteurs ou du casque peut provoquer une baisse de
l’acuité auditive.
Pour utiliser ce produit en toute sécurité, évitez l’écoute
prolongée à des pressions sonores excessives.

AVERTISSEMENT :CET AVERTISSEMENT
S’APPLIQUE AUX ÉTATS-UNIS UNIQUEMENT.

Pour les clients en Europe

Ce produit portant la marque CE est conforme à la
Directive sur la compatibilité électromagnétique (EMC)
émise par la Commission de la Communauté
européenne.
La conformité à cette directive implique la conformité
aux normes européennes suivantes:

 EN55103-1: Interférences électromagnétiques

(émission)

 EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans
l’environnement électromagnétique suivant: E4
(environnement EMC contrôlé, ex. studio de télévision).

Pour les clients en Europe

Ce produit a été fabriqué par ou pour le compte de Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075
Japon. Toutes les questions relatives à la conformité des
produits basées sur la législation européenne doivent
être adressées à son représentant, Sony Deutschland

5

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Allemagne.
Pour toute question relative au Service Après-Vente ou à
la Garantie, merci de bien vouloir vous référer aux
coordonnées qui vous sont communiquées dans les
documents « Service (SAV) » ou Garantie.

Ne pas utiliser cet appareil dans une zone résidentielle.

Pour les clients en Europe, Australie et Nouvelle­Zélande
AVERTISSEMENT

Il s’agit d’un produit de Classe A. Dans un
environnement domestique, cet appareil peut provoquer
des interférences radio, dans ce cas l’utilisateur peut être
amené à prendre des mesures appropriées.

Pour les clients au Canada
GARANTIE LIMITÉE DE SONY

- Rendez-vous sur
http://www.sonybiz.ca/pro/lang/en/ca/article/
resources-warranty-product-registration pour
obtenir les informations importantes et l’ensemble des
termes et conditions de la garantie limitée de Sony
applicable à ce produit.

WARNUN G

Um die Gefahr von Bränden oder elektrischen
Schlägen zu verringern, darf dieses Gerät nicht
Regen oder Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schlag zu vermeiden, darf
das Gehäuse nicht geöffnet werden. Überlassen
Sie Wartungsarbeiten stets nur qualifiziertem
Fachpersonal.

DIESES GERÄT MUSS GEERDET WERDEN.

WAR NUN G

Beim Einbau des Geräts ist daher im Festkabel ein leicht
zugänglicher Unterbrecher einzufügen, oder der
Netzstecker muss mit einer in der Nähe des Geräts
befindlichen, leicht zugänglichen Wandsteckdose
verbunden werden. Wenn während des Betriebs eine
Funktionsstörung auftritt, ist der Unterbrecher zu
betätigen bzw. der Netzstecker abzuziehen, damit die
Stromversorgung zum Gerät unterbrochen wird.

VORSICHT

Das Gerät ist nicht tropf- und spritzwassergeschützt. Es
dürfen keine mit Flüssigkeiten gefüllten Gegenstände,
z. B. Vasen, darauf abgestellt werden.

VORSICHT

Solange das Netzkabel an eine Netzsteckdose
angeschlossen ist, bleibt das Gerät auch im
ausgeschalteten Zustand mit dem Stromnetz verbunden.

WAR NUNG

Zu hoher Schalldruck von Ohrhörern und Kopfhörern
kann Gehörschäden verursachen.
Um dieses Produkt sicher zu verwenden, vermeiden Sie
längeres Hören bei sehr hohen Schalldruckpegeln.

WAR NUNG

1. Verwenden Sie ein geprüftes Netzkabel (3-adriges
Stromkabel)/einen geprüften Geräteanschluss/einen
geprüften Stecker mit Schutzkontakten entsprechend
den Sicherheitsvorschriften, die im betreffenden
Land gelten.

2. Verwenden Sie ein Netzkabel (3-adriges
Stromkabel)/einen Geräteanschluss/einen Stecker
mit den geeigneten Anschlusswerten (Volt, Ampere).

Wenn Sie Fragen zur Verwendung von Netzkabel/
Geräteanschluss/Stecker haben, wenden Sie sich bitte an
qualifiziertes Kundendienstpersonal.

Für Kunden in Europa

Dieses Produkt besitzt die CE-Kennzeichnung und
erfüllt die EMV-Richtlinie der EG-Kommission.
Angewandte Normen:

 EN55103-1: Elektromagnetische Verträglichkeit

(Störaussendung)

 EN55103-2: Elektromagnetische Verträglichkeit

(Störfestigkeit)
Für die folgende elektromagnetische Umgebung: E4
(kontrollierter EMV-Bereich, z.B. Fernsehstudio).

Für Kunden in Europa

Dieses Produkt wurde von oder für Sony Corporation,
1-7-1 Konan Minato-ku Tokio, 108-0075 Japan
hergestellt.
Bei Fragen zur Produktkonformität auf Grundlage der
Gesetzgebung der Europäischen Union kontaktieren Sie
bitte den Bevollmächtigten Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland.
Für Kundendienst oder Garantieangelegenheiten
wenden Sie sich bitte an die in den Kundendienst- oder
Garantiedokumenten genannten Adressen.

Dieser Apparat darf nicht im Wohnbereich verwendet
werden.

Für Kunden in Europa, Australien und Neuseeland
WAR NUNG

Dies ist eine Einrichtung, welche die Funk-Entstörung
nach Klasse A besitzt. Diese Einrichtung kann im
Wohnbereich Funkstörungen verursachen; in diesem
Fall kann vom Betreiber verlangt werden, angemessene
Maßnahmen durchzuführen und dafür aufzukommen.

6

For kundene i Norge

Dette utstyret kan kobles til et IT­strømfordelingssystem.

Apparatet må tilkoples jordet stikkontakt

Suomessa asuville asiakkaille

Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan

För kunderna i Sverige

Apparaten skall anslutas till jordat uttag

Інформація для споживачів в Україні.

Обладнання відповідає вимогам:
– Технічного регламенту обмеження використання
деяких небезпечних речовин в електричному та
електронному обладнанні (постанова КМУ від 03/

12/2008 № 1057).

Türkiye’deki müşteriler için
AEEE Yönetmeliğine Uygundur

7

Table of Contents

Precaution ....................................................... 9

On Safety .................................................................. 9

On Installation ......................................................... 9

Connecting to Other Devices ................................ 9

Handling the Screen ............................................... 9

On Burn-in .............................................................. 9

On a Long Period of Use ......................................10

On High Brightness Display ................................ 10

On the Surface of the Unit ................................... 10

On Long Periods of Continuous Use .................. 10

Handling and Maintenance of the Screen .......... 10

On Dew Condensation ......................................... 10

On Repacking ........................................................ 10

Disposal of the Unit .............................................. 11

On Fan Error .......................................................... 11

Location and Function of Parts and

Controls ........................................................ 12

Front Panel............................................................. 12

Input Signals and Adjustable/Setting Items....... 15

Rear Panel .............................................................. 16

Connecting the AC Power Cord ................... 17

Using the Menu .............................................17

Protection of the Setting Values ...................18

Protecting the setting values using the KEY

INHIBIT button .................................................. 18

Protecting the setting values using [Password

Lock] ..................................................................... 18

Adjustment Using the Menus ....................... 19

Items ........................................................................ 19

Adjusting and Changing the Settings ................. 19

[Status] menu ................................................... 19

[User Preset Setting] menu ............................ 20

[Color Temp.] menu ....................................... 21

[User Configuration] menu ...........................21

[Serial Remote] menu ..................................... 27

[Security] menu ............................................... 28

Connecting the SDI Signals .......................... 28

Troubleshooting ...........................................29

Specifications ................................................ 29

Available Signal Formats...................................... 30

Dimensions ................................................... 36

8

Table of Contents

Precaution

On Safety

 Operate the unit only with a power source as specified

in the “Specifications” section.

 A nameplate indicating operating voltage, etc., is

located on the rear panel.

 Should any solid object or liquid fall into the cabinet,

unplug the unit and have it checked by qualified
personnel before operating it any further.

 Do not drop or place heavy objects on the power cord.

If the power cord is damaged, turn off the power
immediately. It is dangerous to use the unit with a
damaged power cord.

 Unplug the unit from the wall outlet if it is not to be

used for several days or more.

 Disconnect the power cord from the AC outlet by

grasping the plug, not by pulling the cord.

 The socket-outlet shall be installed near the

equipment and shall be easily accessible.

On Installation

Handling the Screen

 The OLED panel fitted to this unit is manufactured

with high precision technology, giving a functioning
pixel ratio of at least 99.99%. Thus a very small
proportion of pixels may be “stuck”, either always off
(black), always on (red, green, or blue), or flashing. In
addition, over a long period of use, because of the
physical characteristics of the organic light-emitting
diode, such “stuck” pixels may appear spontaneously.
These problems are not a malfunction.

 Do not leave the screen facing the sun as it can damage

the screen. Take care when you place the unit by a
window.

 Do not push or scratch the monitor’s screen. Do not

place a heavy object on the monitor’s screen. This may
cause the screen to lose uniformity.

 The screen and the cabinet become warm during

operation. This is not a malfunction.

On Burn-in

Due to the characteristics of the material used in the
OLED panel, permanent burn-in or reduction in
brightness may occur.
These problems are not a malfunction.

 Allow adequate air circulation to prevent internal heat

build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.

 Do not install the unit in a location near heat sources

such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration or
shock.

When installing the installation space must be secured
in consideration of the ventilation and service operation.

 Do not block the ventilation slots, and vents of the

fans.

 Leave a space around the unit for ventilation.
 Leave more than 40 cm of space in the rear of the unit

to secure the operation area.
When the unit is installed on the desk or the like, leave at
least 10 cm of space in the top side. Leaving 40 cm or
more of space in the rear of the unit is recommended for
service operation.

Connecting to Other Devices

When connecting this unit to other devices, turn off this
unit and the other devices beforehand. Connecting
while turned on may cause a malfunction to this unit
and the other devices.

Images that may cause burn-in

 Still images in the HDR display
 Masked images with aspect ratios other than 17:9
 Color bars or images that remain static for a long time
 Character or message displays that indicate settings or

the operating state

 On-screen displays such as center markers or area

markers

For details on the HDR (High Dynamic Range) display, see
page 23.

To reduce the risk of burn-in

 Turn off the character and marker displays

Press the MENU button to turn off the character
displays. To turn off the character or marker displays
of the connected equipment, operate the connected
equipment accordingly. For details, refer to the
operation manual of the connected equipment.

 Do not display static images that contain high

brightness display, time codes, markers, or logos for
extended periods. Consider applying a display method
with low level signals of 100% or less.

 Turn off the power when not in use

Turn off the power if the monitor is not to be used for
a prolonged period of time.

Screen saver

This product has a built-in screen saver function to
reduce burn-in. When an almost still image is displayed

Precaution

9

for more than 10 minutes, the screen saver starts
automatically and the brightness of the screen decreases.

On a Long Period of Use

Due to an OLED’s panel structure and characteristics of
materials in its design, displaying static images for
extended periods, or using the unit repeatedly in a high
temperature/high humidity environments may cause
image smearing, burn-in, areas of which brightness is
permanently changed, lines, or a decrease in overall
brightness.

On Long Periods of Continuous Use

Using this unit for extended periods may cause eyestrain
or reduction of eyesight.
As soon as you feel physical discomfort or pain, stop
using this unit immediately and take a break.
If the physical discomfort or pain remains even after
taking a break, consult a physician.

Handling and Maintenance of the Screen

In particular, continued display of an image smaller than
the monitor screen, such as in a different aspect ratio,
may shorten the life of the unit.
Avoid displaying a still image for an extended period, or
using the unit repeatedly in a high temperature/high
humidity environment such an airtight room, or around
the outlet of an air conditioner.

To prevent any of the above issues, we recommend
reducing brightness slightly, and to turn off the power
whenever the unit is not in use.

On High Brightness Display

 Using the unit with the high brightness display for

extended periods may cause eyestrain or reduction of
eyesight. Be sure to take an occasional break when
using.

 Follow RECOMMENDATION ITU-R BT.1702

“Guidance for the reduction of photosensitive
epileptic seizures caused by television” or other
guidelines when using.

 In the HDR display, the display surface may emit heat

when high brightness images are output. Do not touch
the surface.

 When [2.4(HDR)], [S-Log3(HDR)], [S-Log2(HDR)],

or [SMPTE ST.2084(HDR)] is selected for [EOTF] in
the [Input Setting] menu, images are displayed in
HDR (High Dynamic Range).
In this manual, this status is described as “HDR
display.”

For details on the HDR (High Dynamic Range) display, see
page 23.

The surface of the screen is specially coated to reduce
image reflection. Make sure to observe the following
points as improper maintenance procedures may impair
the screen’s performance. In addition, the screen is
vulnerable to damage. Do not scratch or knock against it
using a hard object.

 Be sure to disconnect the AC power cord from the AC

outlet before performing maintenance.

 The surface of the screen is specially coated. Do not

attach adhesive objects, such as stickers, on it.

 The surface of the screen is specially coated. Do not

touch the screen directly.

 Wipe the screen surface gently with the supplied

cleaning cloth or a soft dry cloth to remove dirt.

 Stubborn stains may be removed with the supplied

cl eaning cloth, or a sof t cloth slightly d ampened wi th a
mild detergent solution.

 The screen may become scratched if the cleaning cloth

is dusty.

 Never use strong solvents such as alcohol, benzene,

thinner, acidic or alkaline detergent, detergent with
abrasives, or chemical wipe as these may damage the
screen.

 Use a blower to remove dust from the screen surface.

On Dew Condensation

If the unit is suddenly taken from a cold to a warm
location, or if ambient temperature suddenly rises,
moisture may form on the outer surface of the unit and/
or inside of the unit. This is known as condensation. If
condensation occurs, turn off the unit and wait until the
condensation clears before operating the unit. Operating
the unit while condensation is present may damage the
unit.

On the Surface of the Unit

The surface of the unit becomes extremely hot. Do not
touch the surface with your hand or body during power
distribution. It may cause a burn.

10

Precaution

On Repacking

Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit.

Disposal of the Unit

 Do not dispose of the unit with general waste.

Do not include the monitor with household waste.

 When you dispose of the monitor, you must obey the

law in the relative area or country.

On Fan Error

The unit has a built in fan for cooling. When the fan
stops and the  (Power) switch indicator blinks in red,
turn off the power and contact an authorized Sony
dealer.

Precaution

11

Location and Function of Parts and Controls

Front Panel

 (headphones) jack

The audio signal which is selected by the input select
button is output in stereo sound.
The output audio can be changed in [Audio Setting]
(page 26) of the [User Configuration] menu.

 KEY INHIBIT button

You can turn the setting value protection on or off.
When the setting value is protected with key inhibit, the
value cannot be changed. To change the setting value,
turn protection off by pressing the button for more than
two seconds.

For details, see “Protection of the Setting Values”
(page 18).

 Input select buttons

Press to monitor the signal input to each connector.

SDI 4K button: To monitor the 4K signal through the
SDI IN connector. If you press the button that is
already used to monitor, the input setting is changed.
SDI 2K button: To monitor the 2K signal through the
SDI IN connector. If you press the button that is
already used to monitor, the input setting is changed.
OPTION1/OPTION2 button: For future function
expansion.

 Function buttons

You can turn the assigned function on or off.
The factory setting is as follows;

F1 button: [Mono]
F2 button: [Flicker Free]
F3 button: [Blue Only]
F4 button: [Internal Signal]
F5 button: [User Preset1]
F6 button: [User Preset2]
F7 button: [User Preset3]

You can assign various functions in [Function Button
Setting] (page 26) of the [User Configuration] menu.
The [Function Button Setting] menu can also be
displayed by pressing and holding the function button.

 Rotary encoder

APERTURE knob: Adjusts the picture sharpness.

Turn the knob to the right to make picture sharper and
turn it to the left to make the picture softer. This
adjustment is available while the indicator of the
MANUAL button below the knob is lit.
CHROMA knob: Adjusts the color intensity. Turn the
knob to the right to increase the intensity and turn to
the left to decrease it. This adjustment is available
while the adjustment menu is displayed or the
indicator of the MANUAL button below the knob is lit.

12

Location and Function of Parts and Controls