Sony BVM-L231 Operation Manual

LCD VIDEO MONITOR

BVM-L231

OPERATION MANUAL [English] 1st Edition (Revised 1)

Before operating the unit, please read this manual thoroughly and retain it for future reference.

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

THIS APPARATUS MUST BE EARTHED.

This apparatus is provided with a main switch on the rear panel. Install this apparatus so that user can access the main switch easily.

CAUTION

The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION

The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

WARNING

Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies with the EMC Directive issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards:

• EN55103-1 : Electromagnetic Interference (Emission)

• EN55103-2 : Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio).

The manufacturer of this product is Sony Corporation, 17-1 Konan, Minato-ku, Tokyo, Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

This apparatus shall not be used in the residential area.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Attention-when the product is installed in Rack:

1.Prevention against overloading of branch circuit

When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2.Providing protective earth

When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.

3.Internal air ambient temperature of the rack

When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.

4.Prevention against achieving hazardous condition due to uneven mechanical loading

When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading.

5.Install the equipment while taking the operating temperature of the equipment into consideration

For the operating temperature of the equipment, refer to the specifications of the Operation Manual.

6.When performing the installation, keep the following space away from walls in order to obtain proper exhaust and radiation of heat.

Lower, Upper: 4.4 cm (1

For kundene i Norge

Dette utstyret kan kobles til et IT-strømfordelingssystem.

Apparatet må tilkoples jordet stikkontakt

Suomessa asuville asiakkaille

Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan

För kunderna i Sverige

Apparaten skall anslutas till jordat uttag

/4 inches) or more

Pour les clients en Europe

Ce produit portant la marque CE est conforme à la Directive sur la compatibilité électromagnétique (EMC) émise par la Commission de la Communauté européenne. La conformité à cette directive implique la conformité aux normes européennes suivantes:

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans l’environnement électromagnétique suivant: E4 (environnement EMC contrôlé, ex. studio de télévision).

Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japon. Le représentant autorisé pour EMC et la sécurité des produits est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Allemagne. Pour toute question concernant le service ou la garantie, veuillez consulter les adresses indiquées dans les documents de service ou de garantie séparés.

Ne pas utiliser cet appareil dans une zone résidentielle.

Pour les clients en Europe, Australie et NouvelleZélande

AVERTISSEMENT

Afin de réduire les risques d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.

Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.

CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE.

Cet appareil est doté d’un interrupteur principal sur son panneau arrière. Installez l’appareil de sorte que l’utilisateur puisse facilement accéder à l’interrupteur principal.

ATTENTION

Eviter d’exposer l’appareil à un égouttement ou à des éclaboussures. Ne placer aucun objet rempli de liquide, comme un vase, sur l’appareil.

ATTENTION

Cet appareil n’est pas déconnecté de la source d’alimentation secteur tant qu’il est raccordé à la prise murale, même si l’appareil lui-même a été mis hors tension.

Pour les clients au Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

AVERTISSEMENT

Il s’agit d’un produit de Classe A. Dans un environnement domestique, cet appareil peut provoquer des interférences radio, dans ce cas l’utilisateur peut être amené à prendre des mesures appropriées.

WARNUNG

Um die Gefahr von Bränden oder elektrischen Schlägen zu verringern, darf dieses Gerät nicht Regen oder Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal.

DIESES GERÄT MUSS GEERDET WERDEN.

Dieses Gerät verfügt über einen Hauptschalter an der Rückseite. Installieren Sie das Gerät so, dass der Benutzer leicht auf den Hauptschalter zugreifen kann.

VORSICHT

Das Gerät ist nicht tropf- und spritzwassergeschützt. Es dürfen keine mit Flüssigkeiten gefüllten Gegenstände, z. B. Vasen, darauf abgestellt werden.

VORSICHT

Solange das Netzkabel an eine Netzsteckdose angeschlossen ist, bleibt das Gerät auch im ausgeschalteten Zustand mit dem Strommetz verbunden.

Für Kunden in Europa

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie der EG-Kommission. Angewandte Normen:

• EN55103-1: Elektromagnetische Verträglichkeit (Störaussendung)

• EN55103-2: Elektromagnetische Verträglichkeit (Störfestigkeit)

Für die folgende elektromagnetische Umgebung: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio).

Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. Der autorisierte Repräsentant für EMV und Produktsicherheit ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in Bezug auf Kundendienst oder Garantie wenden Sie sich bitte an die in den separaten Kundendienst- oder Garantiedokumenten aufgeführten Anschriften.

Dieser Apparat darf nicht im Wohnbereich verwendet werden.

Für Kunden in Europa, Australien und Neuseeland

WARNUNG

Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.

Table of Contents

Chapter 1 Overview

Precautions ............................................................................8

On Safety ....................................................................................8

On Installation.............................................................................8

Handling the LCD Screen...........................................................8

On Cleaning ................................................................................8

On Repacking .............................................................................9

On Rack Mounting......................................................................9

Functions Supported in Software Version 1.1..................10

Features................................................................................11

Options .................................................................................13

Input/Output Connector and Adaptor .......................................14

Location and Function of Parts..........................................16

Front Panel................................................................................16

Rear Panel/Left Side Panel .......................................................18

Chapter 2 Preparations

Environments of the Installation Location ........................20

Installing an Input Adaptor .................................................21

Attaching the Cable Holder.................................................22

Changing the Aspect Ratio of the Screen.........................23

Attaching the Bracket..........................................................24

Connections.........................................................................25

Connecting the Controller (BKM-16R)....................................26

Connecting the Multiple Units with the LAN ..........................26

Turning on the Power..........................................................28

Connecting the AC Power Cord ...............................................28

Turning on the Monitor.............................................................28

Settings.................................................................................29

Selecting the Area.....................................................................29

Setting for the LAN to Connect the Multiple Units..................30

Selecting the Monitor (Designation of the Monitor or Group ID

Number).....................................................................31

Assigning the Input Signal to the Channel ...............................31

Setting the Display Mode of the Picture...................................32

Adjusting ..............................................................................32

Chroma/Phase Adjustment .......................................................32

Table of Contents

Chapter 3 Menu

Color Temperature (White Balance) Adjustment..................... 33

Brightness/Contrast Adjustment............................................... 33

Basic Menu Operations...................................................... 35

Menu Operation Buttons ..........................................................35

Displaying the Menu ................................................................36

Setting or Adjusting in the Menu Operation ............................36

Entering the Channel Number ..................................................38

Aborting Menu Operation ........................................................38

Menu Structure.................................................................... 39

Adjustment Menu................................................................ 46

Overview ..................................................................................46

Menu Function and Operation..................................................46

Input Configuration Menu .................................................. 53

Overview ..................................................................................53

Menu Function and Operation..................................................53

Display Setting Menu.......................................................... 61

Overview ..................................................................................61

Menu Function and Operation..................................................61

Display Function Menu....................................................... 64

Overview ..................................................................................64

Menu Function and Operation..................................................64

System Configuration Menu .............................................. 76

Overview ..................................................................................76

Menu Function and Operation..................................................76

File Management Menu ...................................................... 83

Overview ..................................................................................83

Menu Function and Operation..................................................83

Status Menu......................................................................... 85

Overview ..................................................................................85

Menu Function and Operation..................................................85

Controller Menu .................................................................. 87

Overview ..................................................................................87

Menu Function and Operation..................................................87

Key Protect Menu................................................................ 91

Overview ..................................................................................91

Menu Function and Operation..................................................91

Chapter 4 Operations

Table of Contents

Selecting Display Mode...................................................... 92

Setting the Display of Native Scan Mode ......................... 93

Selecting the Native Scan/Scan Mode...............................94

Displaying Two Signals on One Screen

(Picture&Picture).....................................................95

Magnifying the Picture (Pixel Zoom)..................................96

Displaying the Picture in Black Detail Mode.....................97

Capturing the Picture of the HD Signal

(HD Frame Capture)................................................98

Displaying the Area Marker or Aspect Marker ..................99

Displaying the Audio Level Meter ....................................100

Displaying the Time Code.................................................101

Switching the Display of the 3D Video Signal.................101

Copying the Setting or Adjustment Value to Another

Monitor...................................................................102

Assigning the Function on the Function Button ............103

Upgrading the Monitor and Controller.............................104

Saving the Upgrade Data in a “Memory Stick PRO”.............104

Upgrading the Monitor ...........................................................104

Upgrading the Controller........................................................105

Appendixes

Specifications ....................................................................107

Input Signals and Adjustable/Setting Items....................109

Available Signal Systems .................................................111

Available Signal Formats..................................................113

Aperture Modification Frequency ....................................119

Picture Display Size...........................................................120

Picture·Frame Display.......................................................123

Matrix/Gamma Setting Table ............................................126

Scan Mode Image ..............................................................134

Troubleshooting ................................................................137

Dimensions ........................................................................139

Connection Cable Specifications for Color Temperature

Probes....................................................................141

Inserting/Ejecting the “Memory Stick” ............................143

Notes on “Memory Stick”.......................................................143

Menu Index 145

Table of Contents

Chapter 1 Overview

Overview

Precautions

On Safety

• Operate the unit only with a power source as specified in the “Specifications” section.

• A nameplate indicating operating voltage, power consumption, etc., is located on the rear panel.

• Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

• Do not drop or place heavy objects on the power cord. If the power cord is damaged, turn off the power immediately. It is dangerous to use the unit with a damaged power cord.

• Unplug the unit from the wall outlet if it is not to be used for several days or more.

• Disconnect the power cord from the AC outlet by grasping the plug, not by pulling the cord.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

Chapter

of pixels may be “stuck”, either always off (black), always on (red, green, or blue), or flashing. In addition, over a long period of use, because of the physical characteristics of the liquid crystal display, such “stuck” pixels may appear spontaneously. These problems are not a malfunction.

• Do not leave the LCD screen facing the sun as it can damage the LCD screen. Take care when you place the unit by a window.

• Do not push or scratch the LCD monitor’s screen. Do not place a heavy object on the LCD monitor’s screen. This may cause the screen to lose uniformity.

• If the unit is used in a cold place, horizontal lines or a residual image may appear on the screen. This is not a malfunction. When the monitor becomes warm, the screen returns to normal.

• If a fixed picture such as a frame of a divided picture or time code, or a still picture is displayed for a long time, an image may remain on the screen and be superimposed as a ghosting image.

• The screen and the cabinet become warm during operation. This is not a malfunction.

On Cleaning

On Installation

• Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.

• Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

Handling the LCD Screen

• The LCD panel fitted to this unit is manufactured with high precision technology, giving a functioning pixel ratio of at least 99.99%. Thus a very small proportion

Precautions

Before cleaning

Be sure to disconnect the AC power cord from the AC outlet.

On cleaning the monitor screen

The monitor screen surface is especially treated to reduce reflection of light. As incorrect maintenance may impair the performance of the monitor, take care with respect to the following:

• Wipe the screen gently with a soft cloth such as a cleaning cloth or glass cleaning cloth. If you wipe the screen using too much force, the screen surface may lose uniformity or the LCD panel may malfunction. Never use tissue as it may scar the surface of the screen.

• Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.

• Never use solvent such as alcohol, benzene or thinner, or acid, alkaline or abrasive detergent, or chemical cleaning cloth, as they will damage the screen surface.

On cleaning the cabinet

• Clean the cabinet gently with a soft dry cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution, followed by wiping with a soft dry cloth.

• Use of alcohol, benzene, thinner or insecticide may damage the finish of the cabinet or remove the indications on the cabinet. Do not use these chemicals.

• If you rub on the cabinet with a stained cloth, the cabinet may be scratched.

• If the cabinet is in contact with a rubber or vinyl resin product for a long period of time, the finish of the cabinet may deteriorate or the coating may come off.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container which to transport the unit.

Chapter 1 Overview

On Rack Mounting

When the monitor is mounted on a rack, the temperature around the monitor may rise due to heat generated from other equipment and reduced air circulation, causing damage to the monitor. To prevent this, keep the space around the monitor (1U or more space above and below the monitor), and install a ventilation fan or take other effective countermeasures so that the temperature around the monitor is within the specified range: operating temperature range of 0 to 35 °C (32 to 95°F).

If you have any questions about this unit, please contact your Sony service representative.

Precautions

Functions Supported in Software Version 1.1

The following new functions are supported for Version 1.1 of the BVM-L231.

Chapter 1 Overview

Menu Supported function Reference page

• Checkerboard

• L/R Switch

(in the Function Switch menu of the Display Function menu) (in the Parallel Remote menu of the System Configuration menu) (in the Function Key menu of the Controller menu)

Simultaneous display or left/right switching display of the left and right 3D video signals is available by installing an optional BKM-250TG (with serial number 7100001 or higher).

74, 79, 90, 101

Functions Supported in Software Version 1.1

Features

The BVM-L231 is 23-inch LCD Video Monitor. This is suitable for television stations or video production houses, where precise image reproduction is required.

The BVM-L231 features flat panel and “TRIMASTER*”, which is a new technology developed for three elements, “accurate color reproduction”, “precision imaging” and “quality picture consistency,” that are in demand for professional use. “TRIMASTER” decreases the viewing difference that occurs due to the individuality of each panel. Also, the BVM-L231 realizes the high picture quality and high-trust required for the master monitor by the color management system with its wide color gamut device, high-resolution/precise gradation display, animation improvement technology and signal processing of high accuracy/calibration/feedback system.

* TRIMASTER is a trademark of Sony Corporation.

23-inch LCD panel developed for the BVM-L231

The 23-inch (22.5 inch) LCD panel was developed for the BVM-L231 and supports the full HD signal. It offers a 10-bit driver, high-speed response, high resolution and high color gradation.

Backlight system by LED with high-purity technology

High-purity LEDs enable the wider color space. The precision backlight system also incorporates a uniformity control function and a color feedback system.

12-bit precision display engine for professional use

The panel is equipped with a unique signal process engine developed for the professional use monitor. This engine incorporates 12-bit output accuracy at each process, and provides a high-quality I/P conversion algorithm, scaling processing, panel driving and a highly accurate color management system.

Multi color space

A backlight system with high-precision technology and color management system which uses the unique 3D LUT (Look Up Table) reproduces the color space that complies with the broadcast standard ITU-R BT.709, EBU and SMPTE-C accurately. A wider color space* allows digital cinema reproductions.

* The RGB chromaticity of SMPTE RP 431-2 is not

covered in full.

High-quality I/P conversion processing

A high-quality picture near the original one, in which jagged lines and conversion errors are decreased by detecting the feature of the picture inside the subdivided block and processing properly, is reproduced.

The signal delay is decreased by judging the animation or still picture from the past video signal. Film cadence processing, which converts the signal composed of 2-2·23·2-3-3-2 pull down to the I/P signal closely following the original, is also selectable.

Interlace display mode

The interlace signal is displayed as the interlace picture by inserting the black line without I/P conversion processing. A picture faithful to the original signal and with the same feel as a CRT is gained.

For setting the display, see “Selecting Display Mode” on page 92.

Black frame insertion display mode

Monitor blur caused by the holding-type display of the LCD is decreased by blinking the backlight in synchronization with the LCD display frame in double frame rate (100/120Hz) operation of the LCD panel.

For setting the display, see “Selecting Display Mode” on page 92.

Available to a multi signal format

The monitor supports various input signals such as 720 × 576/50i to 1920 × 1080/50P, 60P, digital cinema (D-Cine) 2048 × 1080/24P and variable computer signals up to WUXGA (1920 × 1200). A DVI-D (HDCP correspondence), HDMI* (HDCP correspondence) and four option slots are equipped as the interface and the monitor supports HD-SDI, Dual-link HD-SDI, 3G-SDI, SD-SDI, RGB, YPbPr, Y/C and composite signal input.

* HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI Licensing LLC.

HD frame capture function

The frame of the 3G/HD-SDI input signal is captured and saved as a picture file in the “Memory Stick”. This is used to confirm the color tone and picture angle of the current scene and recorded scene by using the multi display (Picture&Picture) function.

* As the frame of the input signal is captured, the data and

marker set by the monitor is not reflected.

For the operation, see “Capturing the Picture of the HD Signal (HD Frame Capture)” on page 98.

Multi display function

Two kinds of input signals are output on the monitor. You can select from side by side, wipe, butterfly and blending mode. This is useful for adjusting the color or comparing two pictures.

For the operation, see “Displaying Two Signals on One Screen (Picture&Picture)” on page 95.

Chapter 1 Overview

Features

Pixel zoom function

As part of the picture is magnified up to 8 times without scaling processing, this is convenient for confirming a minute part of the signal.

For the operation, see “Magnifying the Picture (Pixel

Chapter 1 Overview

Zoom)” on page 96.

Safe area marker and aspect marker functions

The monitor is equipped with two area markers and center marker as the safe area marker and aspect marker for confirming the picture angle.

For the operation, see “Displaying the Area Marker or Aspect Marker” on page 99.

Scan selection/Native scan display function

You can select from under scan (–3%), normal scan (0%) and over scan (mask of the 5% over scan portion in the normal scan) for the picture display. The monitor is equipped with a native scan display function which maps the pixel of the signal to the panel in one-to-one mode. You can select the mode from ×1, ×2 or Aspect Correction to display a signal in native mode. An SD signal of non-square pixels (the number of H pixels of the signal system is 720 or 1440) or a 640 × 480 SD signal of DVI video/HDMI video is displayed correctly by scaling processing of doubling for the V direction and correct aspect ratio for the H direction, and the picture is also optimized and displayed by modifying the aperture coefficient value, filter coefficient value, etc. in Aspect Correction mode.

* When the aspect ratio is set to 2.39:1, the resolution is

reduced.

Remote control function (Ethernet control)

The controller controls up to 32 monitors by the Ethernet (10BASE-T/100BASE-TX) connection. Up to four controllers are connected to one monitor in single mode. You can control individual monitors or monitor groups simply by entering the monitor ID number or group ID number. You can also execute the same operation on all connected monitors, or put all connected monitors into the same setup and adjustment state.

Closed caption display function

EIA/CEA-608 or EIA/CEA-708 standard closed caption signals superimposed on the SDI signals are displayed by installing the optional input adaptor (BKM-244CC).

Audio level meter/time code display function

Audio level of the embedded audio and time code signals superimposed on the SDI signals are displayed by installing the optional input adaptor (BKM-250TG).

3D signal analyzing function

Left (L) and right (R) 3D video signals can be displayed in a checkerboard pattern on the same screen, or they can be switched alternately by installing the optional input adaptor (BKM-250TG with serial number 7100001 or higher). For this function, two-dimensional (2D) view is used. The signals are not displayed in stereoscopic view.

For the operation, see “Switching the Display of the 3D Video Signal” on page 101.

For the operation, see “Selecting the Native Scan/Scan Mode” on page 94.

Gamut error function

The signal outside the specified range (gamut error) caused by the conversion of the format or during CG/CM production is displayed in a zebra pattern.

Black detail mode display function

You can reduce to dull black color by backlight leaking and precisely assess any parts with low color gradation. You can decrease the black level up to 40% of the normal display (100 cd/m color gradation (higher than 75 IRE) are clipped by the dynamic range of the circuit, but a zebra pattern (selectable) is displayed in the clipped portions.

For the operation, see “Displaying the Picture in Black Detail Mode” on page 97.

at 100% signal). The parts with high

Aspect selectable function

A squeezed and recorded signal is displayed with the correct angle. You can select from 4:3, 16:9, 1.896:1 and

2.39:1* aspect modes.

Variable picture adjustment functions

Auto chroma, phase and matrix adjustment function are equipped. The white balance is automatically adjusted by using a commercially available probe (Konica Minolta CA-210, DK-Technologies PM5639/06, X-Rite Eye-One Pro).

Other features

• The color temperature is selectable from D65, D93, D61, D56, D-Cine and User.

• Built-in test pattern for 100% white signal, 20% gray signal, 0% black signal, PLUGE (Picture Line Up Generation Equipment) signal, color-bar signal, 5 step gray scale signal and ramp signal.

• Chroma Up function that increases the chroma setting by 12 dB.

• Blue only function and RGB cut off function to monitor signal noise.

• A parallel remote of the contact point control connector is equipped.

Features

Options

For external control

BKM-16R Monitor Control Unit

The BKM-16R is a controller of the BVM-L231 and you can control multiple monitors from one controller.

In this manual, the BKM-16R is referred to as the controller.

For installation

BKM-37H Controller Attachment Stand

Used to join a BKM-16R and the BVM-L231. When the stand is attached to the BVM-L231, you can adjust the monitor angle up or down.

SMF-700 Monitor Interface Cable

Used to connect the BVM-L231 to the BKM-16R.

BKM-23M Monitor Protection Panel

The BKM-23M is a panel to protect the LCD panel of the BVM-L231.

Note

The signal from the MONITOR OUT connector of the BKM-220D does not satisfy the ON-LINE signal specifications.

BKM-227W NTSC/PAL Input Adaptor

Includes a decoder for NTSC/PAL/PAL-M/SECAM signals. Input/output connectors for each one composite signal channel and Y/C signal channel are equipped.

BKM-229X Analog Component Input Adaptor

Includes a decoder for analog component signals and analog RGB signals. Input connector for one channel is equipped.

BKM-243HS HD/D1-SDI Input Adaptor

Includes a decoder for serial digital component signals. Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

Note

The signal from the MONITOR OUT connector of the BKM-243HS does not satisfy the ON-LINE signal specifications.

Chapter 1 Overview

Input adaptors

The input connector panel is composed by installing the optional input adaptor into the input option slot on the side panel of the monitor. Up to four adaptors can be installed to the monitor. The input signal type for each connector of the adaptor is set with the Input Configuration menu, in accordance with the configuration of the connector panel.

Note

When installing the adaptor, be sure to perform the necessary input signal setup with the Input Configuration menu. If the setup is not performed, the adaptors may not function correctly.

For information about the Input Configuration menu, see page 53.

For details of each input adaptor, refer to the operating instructions of each model.

BKM-220D SDI 4:2:2 Input Adaptor

Includes a decoder for serial digital signals (525/625 component). Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

BKM-244CC HD/SD-SDI Closed Caption Adaptor

Includes a decoder for serial digital component signals. EIA/CEA-608 or EIA/CEA-708 standard closed caption signals superimposed on the SDI signals are decoded and displayed. Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

Note

The signal from the MONITOR OUT connector of the BKM-244CC does not satisfy the ON-LINE signal specifications.

BKM-250TG 3G/HD/SD-SDI Input Adaptor

Includes a decoder for serial digital component signals. Time code and audio level of the embedded audio signals superimposed on the SDI signals are displayed. Input/ output connectors for two serial digital channels and output connector for two monitor channels are equipped.

Note

The signal from the MONITOR OUT connector of the BKM-250TG does not satisfy the ON-LINE signal specifications.

Caution

When you install the following input adaptors to this equipment, use those with the serial numbers given below.

• BKM-220D with serial number 2100001 or higher

Options

• BKM-229X with serial number 2200001 or higher

• BKM-243HS with serial number 2108355 or higher

• BKM-250TG with serial number 7100001 or higher BKM-220D: This equipment may not meet the requirements of the electromagnetic interference standard if designated input adaptors are not installed.

Chapter 1 Overview

BKM-229X: This equipment may not work correctly or you may not be satisfied with the performance if designated input adaptors are not installed. BKM-243HS: This equipment may not meet the requirements of the electromagnetic interference standard or work correctly, or you may not be satisfied with the performance if designated input adaptors are not installed. BKM-250TG: The 3D signal analyzing function does not operate if designated input adaptors are not installed.

Input/Output Connector and Adaptor

By adding the optional input expansion adaptors, the input/ output connector panel can be assembled in a wide variety of configurations. The signals that each of the adaptors’ connectors supports are given in the following table. The type of signal to be applied to each input/output connector is set with the Input Configuration menu.

For information about the Input Configuration menu, see page 53.

Options

Input adaptor BKM-

Input signal

Component 525/ 625

Single-link HD-SDI aa

input

Dual-link HD-SDI a(2) a

Serial digital

Single-link 3G-SDI a Composite NTSC a Composite PAL a Composite PAL-M a

Composite SECAM

Y/C NTSC a Y/C PAL a Y/C PAL-M a Y/C SECAM a YPbPr 525i/625i a RGB 525i/625i a

YPbPr/RGB 1080/24PsF

YPbPr/RGB 1080/24P

YPbPr/RGB

Analog input

1080/50i (25PsF)

YPbPr/RGB 1080/25P

YPbPr/RGB 576/50P

YPbPr/RGB 480/60P

YPbPr/RGB 1080/60i (30PsF)

YPbPr/RGB 1080/30P

YPbPr/RGB 720/50P

YPbPr/RGB 720/60P

Number of digital inputs 2 – – 2 2

Number of analog inputs – 1 1 – –

220D

BKM227W

BKM229X

BKM243HS/ 244CC

BKM250TG

Chapter 1 Overview

a: Signal can be reproduced. a(2): Two adaptors are used.

For details, see “Available Signal Formats” on page 113.

Options

Location and Function of Parts

Front Panel

Chapter 1 Overview

6 OPTION B

connector

1 Tally lamp

2 OPERATE lamp

5 OPTION A

connector

a Tally lamp

With factory settings, the tally lamp lights when pins No. 8 and No. 9 of the PARALLEL REMOTE connector on the left side panel are shorted. By changing the setting in the Parallel Remote menu, different pins on the PARALLEL REMOTE connector can be used to control the tally lamp.

For information about the Parallel Remote menu, see “Parallel Remote” (page 77) of the System Configuration Menu.

b OPERATE lamp

Lights in red when the monitor is in standby mode. The monitor will be in standby mode under the following conditions:

• Standby Mode is set to On in the Power menu of the System Configuration menu and the MAIN POWER switch (on the rear panel) is turned on. (The OPERATE lamp will flash for initialization after the switch is turned on, then will light.)

• The monitor is changed from operation mode to standby mode by external control.

Lights in green when the monitor is put into operation mode from standby mode by pressing the MONITOR I/1 switch of the controller.

For information about the Power menu, see “Power” (page 79) of the System Configuration Menu.

3 STATUS lamp

4 OVER RANGE lamp

Notes

• When the lamp is flashing in red, the monitor cannot be put into operation mode. (Internal data initialization is taking place.) Wait until the lamp is steadily lit.

• The lamp may show the error, warning or operation mode.

For details, see “Error/warning/operation mode display by the lamp” on page 17.

c STATUS lamp

Lights in blue when the gamut error is detected. Set the method to clear the error display with Notification Reset (page 68) in the Gamut Error Display menu of the Display Function menu.

Note

The lamp may show the error, warning or operation mode.

For details, see “Error/warning/operation mode display by the lamp” on page 17.

d OVER RANGE lamp

Lights in orange when the picture is displayed in black detail mode or when the dynamic range of the following item is exceeded.

Location and Function of Parts

• Contrast (contrast) Flashes when the luminance is decreased to protect the monitor from a rise in temperature.

For details of the black detail mode display, see “Displaying the Picture in Black Detail Mode” on page

97.

OVER RANGE lamp

Goes out

STATUS lamp

Lights in blue

OPERATE lamp

Flashes in green

LED disconnection of the LED backlight part.

Warning/operation mode display

Symptoms

Chapter 1 Overview

Note

The lamp may show the error, warning or operation mode.

For details, see “Error/warning/operation mode display by the lamp” on page 17.

e OPTION A connector

Used to connect a probe for automatic adjustment.

f OPTION B connector

Used for future expansion. The cover is attached at the factory.

Error/warning/operation mode display by the lamp

The OVER RANGE lamp, STATUS lamp or OPERATE lamp on the front panel may show an error, warning or operation mode while the monitor is being operated.

Error display

If the error is shown, please contact your Sony representative.

OVER RANGE lamp

Flashes in orange

Lights in orange

–: Status except for error display.

STATUS lamp

OPERATE lamp

––

Symptoms

The luminance is reduced to protect the circuit from an increase of temperature in the LED backlight part. g Please contact your

Sony representative.

• The dynamic range of the LED backlight part is exceeded. g Please contact your

Sony representative.

• The dynamic range is exceeded when contrast is adjusted. g Reduce the contrast

setting.

• When the picture is displayed in black detail mode

OVER RANGE lamp

Lights in orange

Flashes in orange

Goes out

Lights in orange

Flashes in orange

STATUS lamp

Goes out

Lights in blue

Flashes in blue

Lights in blue

Goes out

OPERATE lamp

Flashes in red

Flashes in green

Flashes in red

Flashes in green

Symptoms

The power in the LED backlight part is overcurrent.

The power in the LED backlight part is overvoltage.

The LED temperature of the LED backlight part is unusual.

The LED driver temperature of the LED backlight part is unusual.

The temperature sensor is unusual.

The temperature of the LCD panel is unusual.

The RGB sensor of the LED backlight part is unusual.

Fan error.

Location and Function of Parts

Rear Panel/Left Side Panel

Chapter 1 Overview

1 MAIN POWER switch

2 AC IN connector

3 DC 5V OUT connector

4 LAN (10/100) connector

a MAIN POWER switch

When turned on (?), the monitor enters operation mode. By setting in Power menu of the System Configuration menu, the monitor can also be set to enter standby mode when the MAIN POWER switch is turned on.

For information about the Power menu, see “Power” (page 79) of the System Configuration Menu.

b AC IN connector (3-pin)

Connects the monitor to an AC power source, via the supplied AC power cord.

5 NETWORK switch

6 PARALLEL REMOTE connector

7 DVI-D input connector

8 HDMI input connector

9 Input option slots

Connect to the DC 5V/12V IN connector of the controller with the SMF-700 or the cable supplied with the BKM37H.

CAUTION

DC 5V OUT connector (female) is non LPS (Limited Power Source) circuit.

ATTENTION

Le connecteur DC 5V OUT (femelle) est un circuit non LPS (Limited Power Source, source d’alimentation limitée).

c DC 5V OUT connector (female)

Supplies the DC power to the controller.

Location and Function of Parts

d LAN (10/100) connector (10BASE-T/100BASE-TX)

Connect to the LAN (10/100) connector of the controller by using the SMF-700 or the cable supplied with the BKM37H. Or connect to the network or the LAN (10/100) connector of the controller by using a 10BASE-T/ 100BASE-TX LAN cable (shielded-type, optional).

CAUTION

• For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

• When you connect the LAN cable of the unit to peripheral device, use a shielded-type cable to prevent malfunction due to radiation noise.

• To connect the monitor to the LAN (10/100) connector of the controller in 1 to 1 connection (NETWORK switch is set to PEER TO PEER), use a straight (shielded-type) cable.

• The connection speed may be affected by the network system.

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour le câblage de périphériques pouvant avoir une tension excessive à ce port. Suivez les instructions pour ce port.

ACHTUNG

Aus Sicherheitsgründen nicht mit einem PeripheriegerätAnschluss verbinden, der zu starke Spannung für diese Buchse haben könnte. Folgen Sie den Anweisungen für diese Buchse.

e NETWORK switch LAN: To connect to the network. PEER TO PEER: To connect to the LAN (10/100)

connector of the controller in 1 to 1 connection.

f PARALLEL REMOTE connector (D-sub 9-pin,

female)

Forms a parallel switch and controls the monitor externally. The pin assignment and factory setting function assigned to each pin are given below.

Pin number Function

3 Selects sync signal (SYNC button

function).

4 Selects whether monochrome image is

5 Marker (set in the Marker Setting

6, 7 Not connected

8 Tally lamp On/Off

9Ground

displayed or the monitor switches the display mode automatically between color image and monochrome image depending on the input signal (MONO button function).

menu) On/Off (MARKER button function).

All pin function assignments can be changed with the Parallel Remote menu.

For information about the Parallel Remote menu, see “Parallel Remote” (page 77) of the System Configuration Menu.

To switch each function between On and Off or between enable and disable, change pin connections in the following way.

On or enabled: Short each pin and pin 9 together. Off or disabled: Leave each pin open.

g DVI-D (digital DVI) input connector

Inputs DVI Rev.1.0 applicable Single-link digital RGB signal. To monitor the DVI signal of SXGA or higher resolution, use the cable within 3 m (118

/8 inches) in length.

h HDMI input connector

Inputs the HDMI signal. HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection, allowing you to display high quality digital picture. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals.

Chapter 1 Overview

Pin number Function

1 Sets input signal channel 1 (numeric

keypad function).

2 Sets input signal channel 2 (numeric

keypad function).

Notes

• The HDMI audio signal is not available for this monitor.

• Use HDMI compliant cable (optional), Category 2 (High Speed HDMI cable), with HDMI logo.

i Input option slots

Used to install the optional input adaptors.

For installing the input adaptor, see page 21.

For the input signals, see “Input/Output Connector and Adaptor” on page 14.

Location and Function of Parts

Preparations

Chapter 2 Preparations

Chapter

Environments of the Installation Location

Illumination environments

The apparent color reproduction on the monitor is greatly affected by ambient light or glare. The LCD device controls the brightness by moving LCD molecules with the backlight always lit. For this reason, in a dark place, an LCD monitor screen shows very dim light leaks from the black image. We recommend that you adjust the ambient light and use in an environment that does not degrade the reproduction of black.

Viewing angle

The ideal viewing angle is within 5 degrees (up/down/left/ right) off the center of the monitor screen when the operator views the entire monitor screen. Keep the viewing angle within 15 degrees off the center of the monitor screen.

Environments of the Installation Location

Installing an Input Adaptor

Each input adaptor can be installed in any input option slot on the side panel.

Board

Caution

When you install the following input adaptors to this equipment, use those with the serial numbers given below.

• BKM-220D with serial number 2100001 or higher

• BKM-229X with serial number 2200001 or higher

• BKM-243HS with serial number 2108355 or higher BKM-220D: This equipment may not meet the requirements of the electromagnetic interference standard if designated input adaptors are not installed. BKM-229X: This equipment may not work correctly or you may not be satisfied with their performance if designated input adaptors are not installed. BKM-243HS: This equipment may not meet the requirements of the electromagnetic interference standard or work correctly, or you may not be satisfied with the performance if designated input adaptors are not installed.

Note

Turn off the MAIN POWER switch of the monitor and disconnect the AC power cord before installing or removing adaptors.

Loosen two screws and remove the cover of an input option slot on the side panel of the monitor.

Push the adaptor in until it is firmly fit into the connector inside the monitor, then tighten the two screws to secure the adaptor.

Chapter 2 Preparations

Make sure the MAIN POWER switch is turned off, and disconnect the AC power cord.

Insert the adaptor facing the board as shown below.

Cover of an input option slot

For Dual-link operation

Two BKM-243HS or BKM-244CC input adaptors or one BKM-250TG input adaptor is required. When the BKM243HS or BKM-244CC adaptors are used, install the input adaptors in OPTION 1 and 2 option slots, or OPTION 3 and 4 option slots. The BKM-243HS or BKM-244CC cannot be used with the BKM-250TG for Dual-link operation.

To connect the cable

When the BKM-243HS or BKM-244CC adaptors are used, install the Link A signal to OPTION 1 or 3, and the

Link B signal to OPTION 2 or 4.

Installing an Input Adaptor

Connect the cable to the same input number (both INPUT 1 or both INPUT 2) of the input adaptors installed in OPTION 1 and 2 option slots, or OPTION 3 and 4 option slots.

Example of Dual-link cable connection

Chapter 2 Preparations

OPTION 1 and 2

INPUT 1

INPUT 2

INPUT 1

INPUT 2

Attaching the Cable Holder

The cables connected to the input adaptors can be gathered together in the supplied cable holder.

Remove the screw.

OPTION 3 and 4

When the BKM-250TG is used, install the Link A signal to INPUT 1, and the Link B signal to INPUT 2.

INPUT 1

INPUT 2

Attach the cable holder to the monitor with the removed screw.

Cable holder (supplied)

For 3D signal analyzing function

Use a 3D-compatible BKM-250TG (with serial number 7100001 or higher) and input the left 3D signal to INPUT 1 and the right signal to INPUT 2.

Attaching the Cable Holder

Gather the cables together in the cable holder.

Changing the Aspect Ratio of the Screen

The 16:9 frame is installed at the factory. The aspect ratio can be switched from 16:9 to 16:10 by removing the 16:9 frame. To display the native scan picture (×2 mode) of the 576/50i signal, or whole picture of the UXGA or WUXGA signal, remove the 16:9 frame.

Remove the front frame.

Chapter 2 Preparations

Remove 10 screws and then remove the 16:9 frame.

Changing the Aspect Ratio of the Screen

Replace the front frame by pressing it until it clicks.

Chapter 2 Preparations

Attaching the 16:9 frame

Remove the front frame.

Replace the 16:9 frame and secure it with 10 screws.

Replace the front frame by pressing it until it clicks.

Attaching the Bracket

You can prevent falling of the monitor by using the supplied bracket.

Remove three screws from the bracket.

Bracket (supplied)

Attach the bracket on the rear panel of the monitor with the three removed screws.

Attaching the Bracket

Attach a piece of string, etc. to the bracket and secure it to the floor or wall.

Bracket

String, etc.

Connections

Note on connecting the cable to the DC 5V OUT connector

Be sure to plug the male connector of the cable into the DC 5V OUT connector of the monitor. Insert the connector so as to fit the shape of the DC 5V OUT connector.

Plug the male connector into the monitor.

Chapter 2 Preparations

Connections

Connecting the Controller (BKM16R)

Monitor

PEER TO PEER

Chapter 2 Preparations

NETWORK

LAN

Set to PEER TO PEER.

LAN (10/100) connector

SMF-700, etc.

Or connect the output cable of the AC adaptor supplied with the controller to the DC 5V/12V IN connector of the controller.

Connecting the Multiple Units with the LAN

DC 5V OUT connector

The controller controls up to 32 monitors. Up to four controllers are connected to one monitor in single mode.

Note

The controller cannot control monitors in another subnetwork.

DC 5V/12V IN

Controller (BKM-16R)

Turn off the MAIN POWER switch of the monitor

connector

NETWORK

LAN

Set to PEER TO PEER.

PEER TO PEER

LAN (10/100) connector

before connecting the units.

Set the NETWORK switches of the monitor and the controller to PEER TO PEER.

Connect the LAN (10/100) connector of the monitor and the LAN (10/100) connector of the controller by using the SMF-700 or the cable supplied with the BKM-37H, or a 10BASE-T/100BASE-TX straight LAN cable (shielded-type, optional).

Note

When an optional LAN cable is connected, use a shielded-type cable to prevent a malfunction due to noises.

Connect the DC 5V OUT connector of the monitor and the DC 5V/12V IN connector of the controller by using the SMF-700 or the cable supplied with the BKM-37H.

Connections

Monitor

LAN (10/100) connector

PEER TO PEER

NETWORK

LAN

Set to LAN.

AC adaptor (supplied with the BKM-16R)

Monitor

LAN (10/100) connector

of a straight/cross cable. When the switching hub without auto selection function is used, connect the monitor and switching hub with the straight cable, and the controller and switching hub with the cross cable.

Connect the output cable on the AC adaptor supplied with controller to the DC 5V/12V IN connector of the controller.

Note

When the multiple units are connected, set for the LAN before setting the NETWORK switch to LAN (page

30).

Set the NETWORK switches of each monitor and the controller to LAN.

Chapter 2 Preparations

Switching hub (recommended: with AUTO MDI/MDI-X function)

DC 5V/12V IN connector

Controller (BKM-16R)

NETWORK

LAN

Turn off the MAIN POWER switch of the monitor

PEER TO PEER

Set to LAN.

LAN (10/100) connector

before connecting the units.

Connect to the network by using a 10BASE-T/ 100BASE-TX cable (shielded-type, optional).

Notes

• When an optional LAN cable is connected, use a shielded-type cable to prevent a malfunction due to noises.

• We recommend to use an optional switching hub with auto selection function (AUTO MDI/MDI-X)

Connections

Turning on the Power

Connecting the AC Power Cord

Plug the AC power cord into the AC IN connector on the rear panel. Then, attach the AC plug holder

Chapter 2 Preparations

(supplied) to the AC power cord.

AC power cord (supplied)

AC plug holder (supplied)

Attach the AC plug holder to the AC power cord, and connect the cord to the AC IN connector so that the cord does not come loose.

The warm-up time is more than 30 minutes, approximately.

When the monitor is in standby mode

As the OPERATE lamp lights in red in standby mode, press the MONITOR I/1 switch of the controller. The OPERATE lamp lights in green and the monitor enters operation mode.

Slide the AC plug holder over the cord until it locks.

To disconnect the AC power cord

Pull out the AC plug holder while pressing the lock levers.

Turning on the Monitor

Press the MAIN POWER switch on the rear panel to turn on the power. When you turn on the monitor for the first time after purchasing it, the Select Area screen is displayed. Select the area where you intend to use this monitor.

For selecting the area, see page 29.

Turning on the Power

Settings

Selecting the Area

When you turn on the monitor for the first time after purchasing it, select the area where you intend to use this monitor from among the options. When the area is selected, the menu item settings suitable for the selected area are applied.

Default value for each area

1North America D65 7.5% Betacam

2Latin America

PAL& PAL-N Area

NTSC&PALM Area

3Africa

Australasia Europe Middle-East

4Asia Except

Japan

5Japan D93 0%

Argentina D65 0%

Paraguay D65 0%

Uruguay D65 0%

Other Area D65 7.5% Betacam

NTSC Area D65 7.5% Betacam

PAL Area D65 0%

Color Tem p

D65 0%

Setup Level

Component

Level

SMPTE/

EBU-N10

SMPTE/

EBU-N10

SMPTE/

EBU-N10

SMPTE/

EBU-N10

SMPTE/

EBU-N10

SMPTE/

EBU-N10

Color

Gamut

Emulation

BVM

SMPTE-C

BVM EBU

BVM

SMPTE-C

BVM EBU

BVM

SMPTE-C

BVM EBU

ENTER button

UP/DOWN buttons

Ent button

Turn on the monitor with the MAIN POWER switch.

The Select Area screen appears.

1 North America

Select Area

North America B

Latin America B Africa B Australasia B Europe B Middle-East B Asia Except Japan B Japan B

Press the UP or DOWN button of the controller to

2 Latin America 3 Africa

Australia/New Zealand

Europe/Russia

Middle East

4 Asia Except Japan 5 Japan

select the area where you intend to use the monitor and press the ENTER (Ent) button.

If you select either Latin America or Asia Except Japan, one of the following screens appears.

If 2 Latin America is selected:

Select Area

Latin America

PAL & PAL-N Area B

NTSC & PAL-M Area B

PAL&PAL-N area

NTSC&PAL-M area

Chapter 2 Preparations

Select PAL & PAL-N or NTSC & PAL-M and press the ENTER (Ent) button.

Settings

If 4 Asia Except Japan is selected:

After saving and reflecting the setting, you can change the setting with the menu.

• Color Temp (color temperature) (page 56)

Select Area

Asia Except Japan

NTSC Area B

PAL Area B

NTSC area

PAL area

• Setup Level (NTSC Setup Level: page 59, Betacam Setup Level: page 59)

• Component Level (page 59)

• Color Gamut Emulation (page 58)

Setting for the LAN to Connect the

Chapter 2 Preparations

Customers who will use this monitor in the shaded areas shown in the map below should select NTSC Area. Other customers should select PAL Area. Then press the ENTER (Ent) button.

Multiple Units

You can control the multiple monitors using the controller connected via each LAN (10/100) connector. You can also control a specific monitor or monitor group.

Set an IP address to the monitors and the controller and a monitor ID number and group ID number to each monitor.

Set the NETWORK switches of each monitor and the controller to PEER TO PEER.

Confirm the settings.

Select Area

XXXXXXXXXX Color Temp: xx Setup Level: xx Component Level: xx

Color Gamut Emulation:

Cancel Confirm

PEER TO PEER

NETWORK

LAN

NETWORK

LAN

Set the different IP address to each monitor and the

PEER TO PEER

controller.

Monitor: Set the IP address in the Network Setting menu of the System Configuration menu (page 76). Controller: Set the IP address in the Network Setting menu of the Controller menu (page 87).

Cancel: Select to cancel the setting and return to the

Select Area screen.

Confirm: Select to save the setting and end selecting

the area.

See “Default value for each area” on page 29 on the

setting value.

Settings

Set Monitor ID and Group ID in the Network menu of the System Configuration menu (page 76).

Set the different monitor ID number to each monitor and if necessary, group ID number. You can use the numbers 1 to 99 as a monitor ID number or group ID number.

+ 122 hidden pages