Sony BDP-S190 User Manual

Page 1
4-410-136-41(1)
Blu-ray Disc™ / DVD Player
Operating Instructions
Getting Started
Playback
Settings and Adjustments
BDP-S190
Page 2

WARNING

Precautions

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
The AC power cord (mains lead) must be changed only at a qualified service shop.
Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION
The use of optical instruments with this product will increase eye hazard. As the laser beam used in this Blu-ray Disc/DVD player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.
This label is located on the laser protective housing inside the enclosure.
Precautions
• This unit operates on 110 V - 240 V AC, 50/60 Hz. Check that the unit’s operating voltage is identical with your local power supply.
• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
• Install this unit so that the AC power cord (mains lead) can be unplugged from the wall socket immediately in the event of trouble.
This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 metres.
On placement
• Place the player in a location with adequate ventilation to prevent heat build-up in the player.
• Do not place the player on a soft surface such as a rug that might block the ventilation holes.
• Do not install this player in a confined space, such as a bookshelf or similar unit.
• Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.
• Do not place the player outdoors, in vehicles, on ships, or on other vessels.
• If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.
• Do not install the player in an inclined position. It is designed to be operated in a horizontal position only.
• Do not place heavy or unstable objects on the player.
• Do not place any objects other than discs on the disc tray. Doing so may cause damage to the player or the object.
• Take out any discs from the tray when you move the player. If you don’t, the disc may be damaged.
• Disconnect the AC power cord (mains lead) and all other cables from the player when you move the player.
2
Page 3
On power sources
• The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off.
• Disconnect the player from the wall outlet if you are not going to use the player for a long time. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.
• Observe following points to prevent the AC power cord (mains lead) being damaged. Do not use the AC power cord (mains lead) if it is damaged, as doing so may result in an electric shock or fire. – Do not pinch the AC power cord (mains
lead) between the player and wall, shelf, etc.
– Do not put anything heavy on the AC
power cord (mains lead) or pull on the AC power cord (mains lead) itself.
On adjusting volume
Do not turn up the volume while listening to a section with very low level inputs or no audio signals. Your ears and the speakers may be damaged when the sound level reaches the peak.
On cleaning
Clean the cabinet, panel, and controls with a soft cloth. Do not use any type of abras ive pad, scouring powder or solvent such as alcohol or benzine.
On cleaning discs, disc/lens cleaners
Do not use cleaning discs or disc/lens cleaners (including wet or spray types). These may cause the apparatus to malfunction.
On replacement of parts
In the events that this player is repaired, repaired parts may be collected for reuse or recycling purposes.
On connecting to the HDMI OUT jack
Observe the following as improper handling may damage the HDMI OUT jack and the connector.
• Carefully align the HDMI OUT jack on the rear of the player and the HDMI connector
by checking their shapes. Make sure the connector is not upside down or tilted.
• Be sure to disconnect the HDMI cable when moving the player.
• Hold the HDMI connector straight when connecting or disconnecting the HDMI cable. Do not twist or force the HDMI connector into the HDMI OUT jack.
IMPORTANT NOTICE
Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panel televisions and projection televisions are susceptible to this.
If you have any questions or problems concerning your player, please consult your nearest Sony dealer.
Copy Protection
Please be advised of the advanced content protection systems used in both Blu-ray Disc™ and DVD media. These systems, called AACS (Advanced Access Content System) and CSS (Content Scra mble System), may contain some restrictions on playback, analogue output, and other similar features. The operation of this product and the restrictions placed may vary depending on the date of purchase, as the go verning board of the
3
Page 4
AACS may adopt or change its restriction rules after the time of purchase.
Cinavia Notice
This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted.
More information about Cinavia technology is provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.
Copyrights and Trademarks
• “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
• Java is a trademark of Oracle and/or its affiliates.
, “XMB,” and “xross media bar” are trademarks of Sony Corporation and Sony Computer Entertainment Inc.
• This product incorporates High-Definition Multimedia Interface (HDMI™) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
• Blu-ray Disc™, Blu-Ray™, BD-Live™, BONUSVIEW™, and the logos are trademarks of the Blu-ray Disc Association.
• “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD-R,” “DVD VIDEO,” and “CD” logos are trademarks.
• “x.v.Colour” and “x.v.Colour” logo are trademarks of Sony Corporation.
• “BRAVIA” is a trademark of Sony Corporation.
• “PhotoTV HD” and the “PhotoTV HD” logo are trademarks of Sony Corporation.
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.
• This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.
• Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropr iate license(s) from Microsoft. Content owners use Microsoft PlayReady™ content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReady-protected content and/or WMDRM-protected content. If the device fails to properly enforce restrictions on content usage, content owners may require Microsoft to revoke the device’s ability to consume PlayReady­protected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
,continued to page 6
4
Page 5
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Started
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 1: Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 2: Connecting the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 3: Preparing for Network Connection . . . . . . . . . . . . . . . . . . . 13
Step 4: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Playback
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Playing from a USB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Playing via a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Available Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Settings and Adjustments
Using the Settings Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
[Network Update] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
[Screen Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
[Audio Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
[BD/DVD Viewing Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
[Parental Control Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
[System Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
[Network Settings] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
[Easy Setup] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
[Resetting] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Additional Information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5
Page 6
•Opera® Browser from Opera Software ASA. Copyright 1995-2010 Opera Software ASA. All rights reserved.
• All other trademarks are trademarks of their respective owners.
• Other system and product names are generally trademarks or registered trademarks of the manufacturers. ™ and ® marks are not indicated in this document.
6
Page 7

Getting Started

Guide to Parts and Controls

Front panel
z
The N button has a tactile dot. Use the tactile dot as a reference when operating the player.
Getting Started
A Disc tray B Z (open/close) C N (play) D x (stop) E Power indicator F [/1 (on/standby)
Turns on the player, or sets to standby mode.
G (USB) jack
Connect a USB device to this jack.
H Remote sensor
To lock the disc tray (Child Lock)
You can lock the disc tray to avoid accidental opening of the tray. While the player is turned on, hold down the N button on the player for more than 10 seconds to lock or unlock the tray.
7
Page 8
Rear panel
VIDEO
R
AUDIO
LINE OUT
DIGITAL OUT
COAXIAL
L
PCM/DTS/ DOLBY DIGITAL
HDMI OUT
LAN(100)
A LINE OUT (VIDEO) jack B DIGITAL OUT (COAXIAL) jack C LAN (100) terminal
D HDMI OUT jack E LINE OUT (R-AUDIO-L) jacks
8
Page 9
Remote
The available functions of the remote are different depending on the disc or the situation.
AUDIO SUBTITLE
DISPLAY
z
Number 5, AUDIO, 2 +, and N buttons have a tactile dot. Use the tactile dot as a reference when operating the player.
SEN
A Z (open/close)
Opens or closes the disc tray.
-TV- t (TV input select)
Switches between TV and other input sources.
-TV- [/1 (TV on/standby)
Turns on the TV, or sets to standby mode.
[/1 (on/standby)
Turns on the player, or sets to standby mode.
B Number buttons (0 - 9)
Enters the title/chapter numbers, etc.
2 (volume) +/–
Adjusts the TV volume.
AUDIO (page 21)
Selects the language track when multi-lingual tracks are recorded on BD-ROMs/DVD VIDEOs. Selects the sound track on CDs.
SUBTITLE (page 21)
Selects the subtitle language when multi-lingual subtitles are recorded on BD-ROMs/DVD VIDEOs.
(muting)
Turns off the sound temporarily.
C Colour buttons (red/green/
yellow/blue)
Shortcut keys for interactive functions.
D TOP MENU
Opens or closes the BD’s or DVD’s Top Menu.
POP UP/MENU
Opens or closes the BD-ROM’s Pop-up Menu, or the DVD’s menu.
OPTIONS (page 17)
Displays the available options on the screen.
Getting Started
9
Page 10
HOME
Enters the player’s home menu. Displays the wall paper when pressed on the category icon of the home menu.
RETURN
Returns to the previous display.
</M/m/,
Moves the highlight to select a displayed item.
Centre button (ENTER)
Enters the selected item.
E ./> (previous/next)
Skips to the previous/next chapter, track, or file.
X (pause)
Pauses or re-starts playback.
m/M (fast reverse/fast forward)
• Fast reverse/fast forward the disc when you press the button during playback. The search speed changes each time you press the button during video playback.
• Plays in slow motion, when pressed for more than one second in pause mode.
• Plays one frame at a time, when you press for a short time in pause mode.
N (play)
Starts or re-starts playback.
DISPLAY (page 16)
Displays the playback information on the screen.
x (stop)
Stops playback and remembers the stop point (resume point). The resume point for a title/track is the last point you played or the last photo for a photo folder.
SEN (page 16)
Accesses the “Sony Entertainment Network™” online service.
Home menu display
The home menu appears when you press HOME. Select a category using </,. Select an item using M/m, and press ENTER.
Item
[Setup]: Adjusts the player settings. [Photo]: Displays photos. [Music]: Plays music. [Video]: Plays videos. [Network]: Displays network items.
Category

Step 1: Supplied Accessories

Check that you have the following items:
• High Speed HDMI Cable (1)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
10
Page 11

Step 2: Connecting the Player

Do not connect the AC power cord (mains lead) until you have made all the connections.
Connecting to your TV
Select one of the following connection methods according to the input jacks on your TV. Match the colour of the plug to that of the jack when connecting.
DIGITAL OUT
PCM/DTS/
COAXIAL
AUDIO
LINE OUT
L
DOLBY DIGITAL
HDMI OUT
LAN(100)
VIDEO
R
Getting Started
High Speed HDMI Cable
(supplied)
Audio/video cable
(not supplied)
High quality
Standard
quality
b
Do not connect the player through a VCR. Video signals from VCRs can be affected by copyright protection systems that cause the picture on the TV to be distorted.
11
Page 12
Connecting to your AV amplifier (receiver)
Select one of the following connection methods according to the input jacks on your AV amplifier (receiver). When you select A or B, make the appropriate settings in the [Audio Settings] setup (page 20).
DIGITAL OUT
PCM/DTS/
COAXIAL
AUDIO
LINE OUT
PCM/DTS/ DOLBY DIGITAL
L
DOLBY DIGITAL
HDMI OUT
LAN(100)
High Speed HDMI Cable (supplied)
Coaxial digital cable
(not supplied)
High Speed HDMI Cable (not supplied)
t Set [BD Audio MIX Setting] (page 20).
VIDEO
R
DIGITAL OUT
COAXIAL
12
t Set [Dolby Digital
Audio/video cable
(not supplied)
*1
/ DTS*2] (page 20).
Page 13
*1
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
*2
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS­HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

Step 3: Preparing for Network Connection

If you are not going to connect the player to a network, proceed to “Step 4: Easy Setup” (page 13).

Step 4: Easy Setup

When turned on for the first time
Wait for a short while before the player turns on and starts [Easy Initial Settings].
Getting Started
1 Insert two R6 (size AA) batteries
by matching the 3 and # ends on the batteries to the markings inside the battery compartment.
Wired Setup
Use a LAN cable to connect to the LAN (100) terminal on the player.
LAN cable (not supplied)
Internet
ADSL modem/ Cable modem
z
Using a shielded interface cable (LAN cable), straight or crossing, is recommended.
Broadband router
2 Plug the player into the mains.
DIGITAL OUT
PCM/DTS/
COAXIAL
DOLBY DIGITAL
VIDEO
R
AUDIO
L
HDMI OUT
LINE OUT
LAN(100)
to mains
3 Press [/1 to turn on the player.
13
Page 14
4 Turn on the TV and set the input
selector on your TV. This will show the signal from the player on your TV screen.
5 Perform [Easy Initial Settings].
Follow the on-screen instructions to make the basic settings using </M/m/, and ENTER on the remote.
</M/m/,
ENTER
b
When [Easy Initial Settings] is complete, select [Easy Network Settings] to use the network functions of the player.
14
Page 15

Playback

Enjoying BONUSVIEW/ BD-LIVE

Playing a Disc

For playable discs, see page 27.
1 Switch the input selector on your
TV so that the signal from the player appears on your TV screen.
2 Press Z, and place a disc on the
disc tray.
Playing side facing down
3 Press Z to close the disc tray.
Playback starts. If playback does not start automatically, select in the [Video], [Music], or [Photo] category, and press ENTER.
Some BD-ROMs with the “BD-LIVE” logo* have bonus contents and other data that can be downloaded for your enjoyment.
*
1 Connect a USB memory to the
USB jack on the player (page 7).
Use a 1 GB or larger USB memory as your local storage.
2 Prepare for BD-LIVE (BD-LIVE
only).
• Connect the player to a network (page 13).
• Set [BD Internet Connection] to [Allow] (page 21).
3 Insert a BD-ROM with
BONUSVIEW/BD-LIVE.
The operation method differs depending on the disc. Refer to the instruction manual supplied with the disc.
z
To delete data in the USB memory, select [Erase BD Data] in the [Video], and press ENTER. All data stored in the b uda folder will be erased.
Playback
15
Page 16
Displaying the play information
You can view the playback information, etc., by pressing DISPLAY. The displayed information differs depending on the disc type and player status.
Example: when playing a BD-ROM

Playing from a USB Device

For “Playable types of files”, see page 28.
1 Connect the USB device to the
USB jack on the player (page 7).
Refer to the instruction manual supplied with the USB device before connecting.
2 Select [Video], [Music],
or [Photo] on the home menu using </,.
3 Select [USB device] using
M/m, and press ENTER.
A Output resolution/Video frequency B Title number or name C The currently selected angle D The currently selected audio setting E Available functions ( angle,
audio, subtitle)
F Playback information
Displays the Play mode, Playing status bar, Disc type, Video codec, Bitrate, Repeat type, Elapsed time, and Total playing time.
G Chapter number
16

Playing via a Network

Enjoying Sony Entertainment Network
Sony Entertainment Network serves as a gateway, delivering the selected Internet content and a variety of on-demand entertainment straight to your player.
z
• Some Internet content requires registration via a PC before it can be played.
• Some Internet content may not be available in some regions/countries.
Page 17
1 Connect the player to a network
(page 13).
2 Press SEN button on the remote. 3 Select an Internet content and a
variety of on-demand entertainment using </M/m/,, and press ENTER.
Video streaming control panel
The control panel appears when the video file starts playing. The displayed items may differ depending on Internet content providers. To display again, press DISPLAY.
A Control display
Press </M/m/, or ENTER for playback operations.
B Playing status bar
Status bar, Cursor indicating the current position, Playing time, Duration of the video file
C Network condition
indicates the wired connection.
D Network transmission speed E The file name of the next video F The file name of the current video
selection

Available Options

Various settings and playback operations are available by pressing OPTIONS. The available items differ depending on the situation.
Common options
x [Repeat Setting]: Sets the repeat
mode.
x [Play]/[Stop]: Starts or stops the
playback.
x [Play from start]: Plays the item
from the beginning.
[Video] only
x [A/V SYNC]: Adjusts the gap between
picture and sound, by delaying the sound output in relation to the picture output (0 to 120 milliseconds).
x [Video Settings]:
– [Picture Quality Mode]: Selects the
picture settings for different lighting environments.
– [BNR]: Reduces the mosaic-like
block noise in the picture.
– [MNR]: Reduces minor noise
around the picture outlines (mosquito noise).
x [Pause]: Pauses the playback. x [Top Menu]: Displays the BD’s or
DVD’s Top Menu.
x [Menu]/[Popup Menu]: Displays the
BD-ROM’s Pop-up Menu or DVD’s menu.
x [Title Search]: Searches for a title on
BD-ROMs/DVD VIDEOs and starts playback from the beginning.
x [Chapter Search]: Searches for a
chapter and starts playback from the beginning.
Playback
17
Page 18
x [Audio]: Switches the language track
when multilingual tracks are recorded on BD-ROMs/DVD VIDEOs. Selects the sound track on CDs.
x [Subtitle]: Switches the subtitle
language when multilingual subtitles are recorded on BD-ROMs/DVD VIDEOs.
x [Angle]: Switches to other viewing
angles when multi-angles are recorded on BD-ROMs/DVD VIDEOs.
x [IP Content Noise Reduction]:
Adjusts the picture quality of Internet contents.
[Music] only
x [Add Slideshow BGM]: Registers
music files in the USB memory as slideshow background music (BGM).
[Photo] only
x [Slideshow Speed]: Changes the
slideshow speed.
x [Slideshow Effect]: Sets the effect
for slideshows.
x [Slideshow BGM]:
– [Off]: Turns off the function. – [My Music from USB]: Sets the
music files registered in [Add Slideshow BGM].
– [Play from Music CD]: Sets the
tracks in CD-DAs.
x [Change Display]: Switches
between [Grid View] and [List View].
x [Slideshow]: Plays a slideshow. x [Rotate Left]: Rotates the photo
counterclockwise by 90 degrees.
x [Rotate Right]: Rotates the photo
clockwise by 90 degrees.
18
Page 19

Settings and Adjustments

[4:3]: Select this when connecting to a 4:3 screen TV without a wide mode function.

Using the Settings Displays

Select [Setup] on the home menu when you need to change the settings of the player. The default settings are underlined.
1 Select [Setup] on the home
menu using </,.
2 Select the setup category icon
using M/m, and press ENTER.

[Network Update]

Select [OK] to update the player’s software via the network.
z
• We recommend performing the network update every 2 months or so.
• For information about update functions, consult your nearest Sony dealer or local authorised Sony Service facility. You can also visit the following website: http://www.sony-asia.com/support/

[Screen Settings]

x [TV Type]
[16:9]: Select this when connecting to a wide-screen TV or a TV with a wide mode function.
x [Screen Format]
[Full]: Select this when connecting to a TV with a wide mode function. Displays a 4:3 screen picture in 16:9 aspect ratio even on a wide-screen TV. [Normal]: Changes the picture size to fit the screen size with the original picture aspect ratio.
x [DVD Aspect Ratio]
[Letter Box]: Displays a wide picture with black bands on the top and bottom.
[Pan & Scan]: Displays a full-height picture on the entire screen, with trimmed sides.
x [Cinema Conversion Mode]
[Auto]: Normally select this. The player automatically detects whether the material is video-based or film-based, and switches to the appropriate conversion method. [Video]: The conversion method suited for video-based material will always be selected regardless of the material.
Settings and Adjustments
19
Page 20
x [Output Video Format]
[HDMI]: Normally select [Auto]. Select [Original Resolution] to output the resolution recorded on the disc. When the resolution is lower than the SD resolution, it is scaled up to the SD resolution. [Video]: Automatically sets the lowest resolution.
[Off]: Select this when the picture is unstable or colours appear unnatural.
x [Pause Mode]
[Auto]: Normally select this. Dynamic moving pictures appear without blurring. [Frame]: Displays static pictures at high resolution.
x [BD-ROM 24p Output]
[Auto]: Outputs 1920 × 1080p/24 Hz video signals only when connecting a 1080/24p-compatible TV using the HDMI OUT jack. [On]: Turns on the function. [Off]: Select this when your TV is not compatible with 1080/24p video signals.
x [DVD-ROM 24p Output]
[Auto]: Outputs 1920 × 1080p/24 Hz video signals only when connecting a 1080/24p-compatible TV using the HDMI OUT jack.
Off]: Select this when your TV is not
[ compatible with 1080/24p video signals.
x [YCbCr/RGB (HDMI)]
[Auto]: Automatically detects the connected TV type, and switches to the matching colour setting. [YCbCr (4:2:2)]: Outputs YCbCr 4:2:2 video signals. [YCbCr (4:4:4)]: Outputs YCbCr 4:4:4 video signals. [RGB]: Outputs RGB video signals.
x [HDMI Deep Colour Output]
[Auto]: Normally select this. [16bit]/[12bit]/[10bit]: Outputs 16bit/ 12bit/10bit video signals when the connected TV is compatible with Deep Colour.

[Audio Settings]

x [Audio (HDMI)]
[Auto]: Normally select this. Outputs audio signals according to the status of the connected HDMI device. [PCM]: Outputs PCM signals from the HDMI OUT jack.
x [BD Audio MIX Setting]
[On]: Outputs the audio obtained by mixing the interactive and secondary audio to the primary audio. [Off]: Outputs the primary audio only. Select this to output HD audio signals to an AV amplifier (receiver).
x [Dolby Digital / DTS]
[Downmix PCM]: Converts to output Linear PCM signals. Select this when connecting an audio device without a built-in Dolby Digital or DTS decoder. [Bitstream] an audio device with a built-in Dolby Digital or DTS decoder.
x [DTS Neo:6]
[Cinema]/[Music]: Outputs the simulated multi-channel sound from 2 channel sources via the HDMI OUT jack according to the capability of the
: Select this when connecting
20
Page 21
connected device using DTS Neo:6 Cinema or DTS Neo:6 Music mode. [Off]
: Outputs the sound with its original number of channels via the HDMI OUT jack.
x [Audio DRC]
[Auto]: Performs playback at the dynamic range specified by the disc (BD-ROM only). Other discs are played back at the [On] level. [On]: Performs playback at a standard compression level. [Off]: No compression works. A more dynamic sound is produced.
x [Downmix]
[Surround]: Outputs audio signals with surround effects. Select this when connecting an audio device that supports Dolby Surround (Pro Logic) or DTS Neo:6. [Stereo]
: Outputs audio signals without surround effects. Select this when connecting an audio device that does not support Dolby Surround (Pro Logic) or DTS Neo:6.
x [Audio Language]
Selects the default track language for BD-ROMs or DVD VIDEOs. When you select [Original], the language given priority in the disc is selected. Select [Select Language Code], and enter the code for your language, referring to “Language code list” (page 30).
x [Subtitle Language]
Selects the default subtitle language for BD-ROMs or DVD VIDEOs. Select [Select Language Code], and enter the code for your language, referring to “Language code list” (page 30).
x [BD Hybrid Disc Playback Layer]
[BD]: Plays BD layer. [DVD/CD]: Plays DVD or CD layer.
x [BD Internet Connection]
[Allow]: Normally select this. [Do not allow] connection.
: Prohibits Internet
Settings and Adjustments

[BD/DVD Viewing Settings]

x [BD/DVD Menu Language]
Selects the default menu language for BD-ROMs or DVD VIDEOs. Select [Select Language Code], and enter the code for your language, referring to “Language code list” (page 30).
[Parental Control
Settings]
x [Password]
Sets or changes the password for the Parental Control function. A password allows you to set a restriction on BD­ROM or DVD VIDEO, and Internet video playback. If necessary, you can differentiate the restriction levels for BD-ROMs, DVD VIDEOs, and Internet videos.
21
Page 22
x [Parental Control Area Code]
Playback of some BD-ROMs, DVD VIDEOs, or Internet videos can be limited according to the geographic area. Scenes may be blocked or replaced with different scenes. Follow the on-screen instructions and enter your four-digit password.
x [BD Parental Control] /
[DVD Parental Control] / [Internet Video Parental Control]
By setting Parental Control, scenes can be blocked or replaced with different scenes. Follow the on-screen instructions and enter your four-digit password.
x [Internet Video Unrated]
[Allow]: Allows the playback of unrated Internet videos. [Block]: Blocks the playback of unrated Internet videos.

[System Settings]

x [OSD Language]
Selects on-screen display language for your player.
x [Control for HDMI]
[On]: The following BRAVIA Sync features are available: – One-Touch Play – System Power-Off – Language Follow [Off]: Turns off the function.
z
For details, refer to the instruction manual supplied with the TV or components.
x [HDMI:Linked to TV-off]
[On]: Automatically turns off the player and HDMI-compatible components when the connected TV enters standby mode (BRAVIA Sync). [Off]: Turns off the function.
x [Quick Start Mode]
[On]: Shortens the startup time when turning on the player.
: Reduces standby power
[Off] consumption.
x [Auto Standby]
[On]: Automatically returns to standby mode if no button is pressed for more than 30 minutes. [Off]: Turns off the function.
x [Auto Display]
[On]: Automatically displays information on the screen when changing the viewing titles, picture modes, audio signals, etc. [Off]: Displays information only when you press DISPLAY.
x [Screen Saver]
[On]: Turns on the screen saver function. The screen saver image appears when you do not use the player for more than 10 minutes while an on-screen display is displayed. [Off]: Turns off the function.
x [Software Update Notification]
[On]: Sets the player to inform you of newer software version information (page 19). [Off]: Turns off the function.
22
Page 23
x [System Information]
Displays the player’s software version information and the MAC address.
x [Software License Information]
Displays information about the Software License.

[Resetting]

x [Reset to Factory Default Settings]
You can reset the player settings to the factory default by selecting the group of settings. All the settings within the group will be reset.

[Network Settings]

x [Internet Settings]
Connect the player to the network beforehand. For details, see “Step 3: Preparing for Network Connection” (page 13). [Wired Setup] connect to a broadband router using a LAN cable. [View Network Status]: Displays the current network status.
x [Network Connection
Diagnostics]
Checks for the proper network connection by running the network diagnostics.
: Select this when you

[Easy Setup]

x [Easy Initial Settings]
Select [Easy Initial Settings] to specify the basic settings. Follow the on-screen instructions.
x [Initialize Personal Information]
You can erase your personal information stored in the player.
Settings and Adjustments
x [Easy Network Settings]
Select [Easy Network Settings] to specify the network settings. Follow the on-screen instructions.
23
Page 24

Additional Information

Troubleshooting

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer.
Picture
, For BD-ROMs, check the [BD-ROM
24p Output] or [DVD-ROM 24p Output] setting in the [Screen Settings] setup (page 20).
The display language on the screen switches automatically when connected to the HDMI OUT jack.
, When [Control for HDMI] is set to
[On] (page 22), the display language on the screen automatically switches according to the language setting of the connected TV (if you change the setting on your TV, etc.).
There is no picture or the picture is not output correctly.
, Check that all the connecting cables
are securely connected (page 11).
, Switch the input selector on your TV
to display the signal from the player.
, Reset the video output resolution to the
lowest resolution by pressing x on the player for more than 10 seconds.
, For HDMI connections, try the
following: on again. equipment off and on again.
3Disconnect and then reconnect the
HDMI cable.
, The HDMI OUT jack is connected to a
DVI device that does not support copyright protection technology.
, For HDMI connections, check the
[Output Video Format] settings in the [Screen Settings] setup (page 20).
, When the analogue signals are also
output, set [BD-ROM 24p Output] or [DVD-ROM 24p Output] to [Off] in the [Screen Settings] setup (page 20).
1Turn the player off and
2Turn the connected
24
Sound
There is no sound or the sound is not output correctly.
, Check that all the connecting cables
are securely connected (page 11).
, Switch the input selector on your AV
amplifier (receiver) so that the audio signals of the player are output from your AV amplifier (receiver).
, If the audio signal does not come
through the DIGITAL OUT (COAXIAL)/HDMI OUT jack, check the audio settings (page 20).
, For HDMI connections, try the
following: on again. equipment off and on again.
3Disconnect and then reconnect the
HDMI cable.
, For HDMI connections, if the player is
connected to a TV through an AV amplifier (receiver), try connecting the HDMI cable directly to the TV. Refer also to the instruction manual supplied with the AV amplifier (receiver).
, The HDMI OUT jack is connected to a
DVI device (DVI jacks do not accept audio signals).
1Turn the player off and
2Turn the connected
Page 25
, The device connected to the HDMI
OUT jack does not support the audio format of the player. Check the audio settings (page 20).
, If the USB device is connected via a
USB hub, connect the USB device directly to the player.
The HD Audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio, and DTS-HD Master Audio) is not output by bitstream.
, Set [BD Audio MIX Setting] to [Off]
in the [Audio Settings] setup (page 20).
, Check that the connecte d AV amplifier
(receiver) is compatible with each HD Audio format.
The interactive audio is not output.
, Set [BD Audio MIX Setting] to [On] in
the [Audio Settings] setup (page 20).
Disc
The disc does not play.
, The disc is dirty or skewed. , The disc is upside down. Insert the disc
with the playback side facing down.
, The disc has a format that cannot be
played back by this player (page 28).
, The player cannot play a recorded disc
that is not correctly finalised.
, The region code on the BD or DVD
does not match the player.
USB device
The player does not detect a USB device connected to the player.
, Make sure that the USB device is
securely connected to the USB jack.
, Check if the USB device or a cable is
damaged.
, Check if the USB device is on.
Sony Entertainment Network
The picture/sound is poor/certain programmes display a loss of detail, especially during fast-motion or dark scenes.
, Picture/sound quality may be
improved by changing the connection speed. Recommended connection speed is of at least 2.5 Mbps for standard definition video (10 Mbps for high definition video).
The picture is small.
, Press M to zoom in.
Network connection
The player cannot connect to the network.
, Check the network connection
(page 13) and the network settings (page 23).
The message [A new software version is available. Please go to the “Setup” section of the menu and select “Network update” to perform the update.] appears on the screen when turning the player on.
, See [Network Update] (page 19) to
update the player to a newer software version.
Additional Information
25
Page 26
Control for HDMI (BRAVIA Sync)
The [Control for HDMI] function does not work (BRAVIA Sync).
, Check that [Control for HDMI] is set
to [On] (page 22).
, If you change the HDMI connection,
turn the player off and on again.
, If power failure occurs, set [Control
for HDMI] to [Off], then set [Control for HDMI] to [On] (page 22).
, Check the following and refer to the
instruction manual supplied with the component. – the connected component is
compatible with the [Control for HDMI] function.
– the connected component’s setting
for the [Control for HDMI] function is correct.
, When you connect the player to a TV
through an AV amplifier (receiver), – if the AV amplifier (receiver) is not
compatible with the [Control for HDMI] function, you may be unable to control the TV from the player.
– if you change the HDMI
connection, disconnect and reconnect the AC power cord (mains lead), or a power failure occurs, try the following: the input selector of the AV amplifier (receiver) so that the picture from the player appears on the TV screen. HDMI] to [Off], then set [Control for HDMI] to [On] (page 22). Refer to the instruction manual supplied with the AV amplifier (receiver).
2Set [Control for
1Switch
The System Power-Off function does not work (BRAVIA Sync).
, Check that [Control for HDMI] and
[HDMI:Linked to TV-off] are set to [On] (page 22).
Others
Playback does not start from the beginning of content.
, Press OPTIONS, and select [Play from
start].
Playback does not start from the resume point where you last stopped playing.
, The resume point may be cleared from
memory depending on the disc when – you open the disc tray. – you disconnect the USB device. – you play other content. – you turn off the player.
The disc tray does not open and you cannot remove the disc even after you press Z.
, Try the following: 1Turn the player
off, and disconnect the AC power cord (mains lead). power cord (mains lead) while pressing down Z on the player.
3Keep pressing down Z on the player
until the tray opens. disc. for more than 10 seconds until the player turns off.
2Reconnect the AC
4Remove the
5Hold down [/1 on the player
26
Page 27
The player does not respond to any button.
, Moisture has condensed inside the
player (page 2).
, Hold down [/1 on the player for more
than 10 seconds until the player turns off. If the player still does not respond to any button, disconnect then reconnect the AC power cord (mains lead).

Specifications

System
Laser: Semiconductor laser
Inputs and outputs
(Jack name:
Jack type/Output level/Load impedance)
LINE OUT R-AUDIO-L:
Phono jack/2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL):
Phono jack/0.5 Vp-p/75 ohms
HDMI OUT:
HDMI 19-pin standard connector
LINE OUT VIDEO:
Phono jack/1.0 Vp-p/75 ohms
LAN (100):
100BASE-TX Terminal
USB:
USB jack Type A, maximum current 500 mA (For connecting USB device)
General
Power requirements:
110 V - 240 V AC, 50/60 Hz
Power consumption: 10 W Dimensions (approx.):
290 mm × 196 mm × 43 mm (width/depth/height) incl. projecting parts
Mass (approx.): 1.1 kg Operating temperature:
5ºC to 35ºC
Operating humidity:
25 % to 80 %
Supplied accessories
See page 10.
Specifications and design are subject to change without notice.
Playable discs
Blu-ray
*1
Disc
*3
DVD
*3
CD
*1
Since the Blu-ray Disc specifications are new and evolving, some discs may not be playable depending on the disc type and the version. The audio output differs depending on the source, connected output jack, and selected audio settings.
*2
BD-RE: Ver.2.1 BD-R: Ver.1.1, 1.2, 1.3 including organic pigment type BD-R (LTH type) The BD-Rs recorded on a PC cannot be played if postscripts are recordable.
*3
A CD or DVD disc will not play if it has not been correctly finalised. For more information, refer to the instruction manual supplied with the recording device.
BD-ROM BD-R
*2
/BD-RE
*2
DVD-ROM DVD-R/DVD-RW DVD+R/DVD+RW
CD-DA (Music CD) CD-ROM CD-R/CD-RW
Additional Information
27
Page 28
Discs that cannot be played
• BDs with cartridge
• BDXLs
•DVD-RAMs
• HD DVDs
• DVD Audio discs
•PHOTO CDs
• Data part of CD-Extras
• Super VCDs
• Audio material side on DualDiscs
Note on Discs
This product is designed to playback discs that conform to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this product.
Note on playback operations of BDs/ DVDs
Some playback operations of BDs/ DVDs may be intentionally set by software producers. Since this player plays BDs/DVDs according to the disc contents the software producers designed, some playback features may not be available.
Note about double-layer BDs/DVDs
The playback pictures and sound may be momentarily interrupted when the layers switch.
Region code (BD-ROM/DVD VIDEO only)
Your player has a region code printed on the rear of the unit and will only play BD-ROMs/DVD VIDEOs labelled with identical region codes or .
ALL
Region code
28
Playable types of files
Video
File format Extensions
MPEG-1 Video/PS MPEG-2 Video/PS,
*1
TS
MPEG-4 AVC
*1
WMV9
*2 *3
AVCHD
Xvid “.avi”
Music
File format Extensions
MP3 (MPEG-1 Audio Layer III)
AAC/HE-AAC
WMA9 Standard
LPCM “.wav”
Photo
File format Extensions
JPEG “.jpg,” “.jpeg”
PNG “.png*5”
GIF “.gif*5”
*1
The player does not play coded file s such as DRM.
*2
This player can play AVCHD Ver.2.0 format.
*3
The player plays AVCHD format files that are recorded on a digital video camera, etc. The AVCHD format disc will not play if it has not been correctly finalised.
*4
The player does not play coded file s such as Lossless.
*5
The player does not play animated PNG or animated GIF files.
*1
*1
*1*4
*1*4
“.mpg,” “.mpeg,” “.m2ts,” “.mts”
“.mkv,” “.mp4,” “.m4v,” “.m2ts,” “.mts”
“.wmv,” “.asf”
“.mp3”
“.m4a”
“.wma”
Page 29
b
• Some files may not play depending on the
format, the encoding, or recording condition.
• Some files edited on a PC may not play.
• The player can recognise the following files
or folders in BDs, DVDs, CDs and USB devices: – up to folders in the 9th layer, including the
root folder
– up to 500 files/folders in a single layer
• Some USB devices may not work with this
player.
• The player can recognise Mass Storage
Class (MSC) devices, Still Image Capture Device (SICD) class devices and 101 keyboard.
• To avoid data corruption or damage to the
USB memory or devices, turn off the player when connecting or removing the USB memory or devices.
• The player may not play high bit rate video
files on DATA CDs smoothly. You are recommended to play such files using DATA DVDs or DATA BDs.
Notes About the Discs
• To keep the disc
clean, handle the disc by its edge. Do not touch the surface. Dust, fingerprints, or scratches on the disc may cause it to malfunction.
• Do not expose the disc to direct
sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a
cleaning cloth. Wipe the disc from the centre out.
• Do not use solvents such as benzine, thinner, commercially available disc/ lens cleaners, or anti-static spray intended for vinyl LPs.
• If you have printed the disc’s label, dry the label before playing.
• Do not use the following discs. – A lens cleaning disc. – A disc that has a non-standard shape
(e.g., card, heart). – A disc with a label or sticker on it. – A disc that has cellophane tape or
sticker adhesive on it.
• Do not resurface the playing side of a disc to remove surface scratches.
Additional Information
Code numbers of controllable TVs
While holding down -TV- [/1, enter the TV manufacturer’s code using the number buttons. If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
Manufacturer Code number
Sony 01 (default)
Hitachi 24
LG/Goldstar 76
Loewe 45
Panasonic 17, 49
Philips 06, 08, 72
Samsung 71
Sharp 29
Toshiba 38
29
Page 30
Language code list
For details, see [BD/DVD Viewing Settings] (page 21). The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
1027 Afar 1028 Abkhazian 1032 Afrikaans 1039 Amharic 1044 Arabic 1045 Assamese 1051 Aymara 1052 Azerbaijani 1053 Bashkir 1057 Byelorussian 1059 Bulgarian 1060 Bihari 1061 Bislama 1066 Bengali 1067 Tibetan 1070 Breton 1079 Catalan 1093 Corsican 1097 Czech 1103 Welsh 1105 Danish 1109 German 1130 Bhutani;
Dzongkha 1144 English 1145 Esperanto 1149 Spanish 1150 Estonian 1151 Basque 1157 Persian 1165 Finnish 1166 Fiji 1171 Faroese 1174 French 1181 Frisian 1183 Irish 1186 Scots Gaelic 1194 Galician 1196 Guarani 1203 Gujarati 1209 Hausa 1217 Hindi 1226 Croatian 1229 Hungarian 1233 Armenian 1235 Interlingua 1239 Interlingue 1245 Inupiak 1248 Indonesian 1253 Icelandic 1254 Italian 1257 Hebrew 1261 Japanese 1269 Yiddish 1283 Javanese 1287 Georgian 1297 Kazakh 1298 Greenlandic;
1299 Cambodian;
Khmer 1301 Korean 1305 Kashmiri 1307 Kurdish 1311 Kirghiz 1313 Latin 1326 Lingala 1327 Laothian; Lao 1332 Lithuanian 1334 Latvian 1345 Malagasy 1347 Maori 1349 Macedonian 1350 Malayalam 1352 Mongolian 1353 Moldavian 1356 Marathi
1142 Greek
Kalaallisut
1300 Kannada
30
Code Language
1357 Malay 1358 Malese;
1363 Burmese 1365 Nauru 1369 Nepali 1376 Dutch 1379 Norwegian 1393 Occitan 1403 Oromo 1408 Oriya 1417 Punjabi;
Panjabi
1435 Pashto;
Pushto
1463 Quechua 1481 Rhaeto-
1482 Kirundi; Rundi 1483 Romanian 1489 Russian 1491 Kinyarwanda 1495 Sanskrit 1498 Sindhi 1501 Sangho;
Sango
1503 Singhalese;
Sinhalese 1506 Slovenian 1507 Samoan 1508 Shona 1509 Somali 1511 Albanian 1512 Serbian 1513 Siswati; Swati 1514 Sesotho;
1515 Sundanese 1516 Swedish 1517 Swahili 1521 Tamil 1525 Telugu 1527 Tajik 1528 Thai 1529 Tigrinya 1531 Turkmen 1532 Tagalog 1534 Setswana;
Tswana 1538 Turkish 1539 Tsonga 1540 Tatar 1543 Twi 1557 Ukrainian 1564 Urdu 1572 Uzbek 1581 Vietnamese 1587 Volapük 1613 Wolof 1632 Xhosa 1665 Yoruba 1684 Chinese 1697 Zulu 1703 Not specified
Maltese
1428 Polish
1436 Portuguese
Romance
1502 Serbo-
Croatian
1505 Slovak
Sotho southern
1535 Tonga; Tonga
islands
Page 31
Parental control/area code
For details, see [Parental Control Area Code] (page 22).
Code Area
2044 Argentina 2047 Australia 2046 Austria 2057 Belgium 2070 Brazil 2090 Chile 2092 China 2093 Colombia 2115 Denmark 2165 Finland 2174 France 2109 Germany 2200 Greece 2219 Hong Kong 2248 India 2238 Indonesia 2239 Ireland 2254 Italy 2276 Japan 2304 Korea 2333 Luxembourg 2363 Malaysia 2362 Mexico 2376 Netherlands 2390 New Zealand 2379 Norway 2427 Pakistan 2424 Philippines 2428 Poland 2436 Portugal 2489 Russia 2501 Singapore 2149 Spain 2499 Sweden 2086 Switzerland 2543 Taiwan 2528 Thailand 2184 United
Kingdom
Additional Information
31
Page 32
The software of this player may be updated in the future. For information about any available updates and the latest Operating Instructions, please visit the following website:
http://www.sony-asia.com/support/
© 2012 Sony Corporation Printed in Malaysia
4-410-136-41(1)
Loading...